GBC 1264WF/1244WF
Operation Manual
GB
I
Operating Instructions
Istruzioni per l'Uso
D
Bedienungsanleitungen
Gebruiksaanwijzing
Mode d'Emploi
NL
F
Part Number:
1264 WF 3600242
1244 WF 3600238
E
Instrucciones de Operación
© 2006 General Binding Corporation
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
TABLE OF CONTENTS
Operation Manual
Page
No.
1
2
3
Page
No.
Description
Description
Top/Bottom Temperature Control
Stop
Reverse
Auto-Off
Ready
Wait
Cover
18
18
18
19
19
19
Legal Disclaimer
Table of Contents
Important Safety Instructions
Important Safeguards
General ,Electric & Service
Warranty
Specifications
Pre- Installation
Installation
4
4
5
5
6
6
Section 8-Safety:
Emergency Stops
Safety Shield
20
20
21
Feed Table
Section 1-Detailed Specifications:
Description
7
7
7
Section 9-How To Guide:
Loading Film
Features
Applications
22
24
25
25
Select and Change Nip Settings
In-Line Slitters
Rear Cut-Off Blade
Section 2-Consumables:
Film Types
8
8
8
8
8
Film Dimensions
Core Size
Film Widths
Section 10-Applicatations:
Film Loading and Threading
Load a Roll of Film
26
27
28
Paper Widths
Webbing Thermal Film using
Threading Card
Webbing PSA Film / Mount Adhesive
Using Threading Card
Start Laminating
Method for Tacking new Film to
Existing Film
Section 3-Function:
Speed
9
9
9
9
9
Motor
Heating Capabilities
Controls
29
30
Roll Design
To Unweb The Laminator
Clearing a Film Jam (Wrap– Up)
31
31
Section 4-Electrical:
Requirements
9
Applications
BTU Output
Heater Wattage
Amperage Draw
D/C Voltage Used
A/C Voltage Used
Plug Configuration and Type
Tips for Pre-Coating Boards
Tips for Mounting Pre-Coated Boards
Tips for Single Sided Lamination
Tips for Creating a Decal
Tips for Mounting a Decal
Thermal Encapsulation
AccuShield
9
32
32
32
33
33
33
34
10
10
10
10
11
Section 5-Dimensions:
Weight
12
12
12
33
Speed/Temperature Control
Dimensions
Nip Height
The Art of Lamination
Basic Rules
Film Tension
Heat
35
35
35
36
Section 6-know your Laminator:
Parts reference Guide
Front View
13
14
14
15
15
16
Output
Rear View
Left Side View
Right Side View
Definition of Parts
37
38
Maintenance
Trouble Shooting Guide
Service Agreement
Section 7-Display Control Panel:
38
Stand-By Mode
Jobs
Measure
Cooling
Run
17
17
17
17
17
© 2006 General Binding Corporation
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFEGUARDS
YOUR SAFETY AS WELL AS THE SAFETY OF
OTHERS IS IMPORTANT TO GBC. IN THIS
INSTRUCTION MANUAL AND ON THE PRODUCT,
YOU WILL FIND IMPORTANT SAFETY MESSAGES
REGARDING THE PRODUCT. READ THESE
MESSAGES CAREFULLY. READ ALL OF THE
WARNING: TO GUARD AGAINST INJURY
THE FOLLOWING SAFETY
PRECAUTIONS MUST BE OBSERVED IN
INSTALLATION AND USE OF THE
LAMINATOR.
General:
INSTRUCTIONS
AND
SAVE
THESE
Keep hands, long hair, loose clothing, and articles such as
necklaces or ties away from the front of the heat and pull
rollers to avoid entanglement and entrapment.
INSTRUCTIONS FOR LATER USE.
THE SAFETY ALERT SYMBOL PRECEDES
EACH SAFETY MESSAGE IN THIS
INSTRUCTION MANUAL. THE SYMBOL
The heat rollers can reach temperatures over 300˚F (150°C).
Avoid contact with the heat rollers during operation or shortly
after power has been removed from the laminator.
INDICATES
A
POTENTIAL PERSONAL
SAFETY HAZARD TO YOU OR OTHERS.
THE FOLLOWING WARNINGS ARE
FOUND UPON THIS PRODUCT.
Keep hands and fingers away from the path of the sharp film
cutter blades.
Do not use the laminator for other than its intended purpose.
ADVERTENCIA
Attention
Avertissement
Avoid moving the Laminator on uneven floor surfaces. Never
tilt the laminator.
Riesgo de choque
eléctrico
No abra:
Adentro no hay
piezas reparables
por el usuario.
Mantenimiento
solamente por
personal calificado
Risque de
Electrical shock
hazard.
Secousseélectrique.
Ne pas ouvrir.
Pas de pièces
réparables par
l'utilisateur.
Entretien
seulement par
personnel qualifié.
Do not open.
No user serviceable
parts inside.
Refer servicing to
qualified service
personnel.
Do not defeat or remove electrical and mechanical safety
equipment such as interlocks, shields and guards.
Do not insert objects unsuitable for laminating or expose the
equipment to liquids.
THIS SAFETY MESSAGE MEANS THAT YOU
COULD BE SERIOUSLY HURT OR KILLED IF YOU
OPEN THE PRODUCT AND EXPOSE YOURSELF
TO HAZARDOUS VOLTAGE.
Electrical:
The Laminator should be connected only to a source of power
as indicated in these instructions and on the serial plate located
on the rear of the laminator. Contact an electrician should the
attachment plug provided with the Laminator not match the
receptacles at your location.
ADVERTENCIA
Attention
Avertissement
RODILLOS
CALIENTES.
PUNTO DE
ROULEAUX
CHAUDS.
POINT DE
HOT ROLLS.
PINCH POINT.
PINCHAMIENTO. PINCEMENT.
Mantener manos y Tenir mains et
Keep hands and
clothing away.
ropa a distancia.
vêtements à
l'écart.
WARNING: THE RECEPTACLE MUST BE
LOCATED NEAR THE EQUIPMENT AND
EASILY ACCESSIBLE.
THIS SAFETY MESSAGE MEANS THAT YOU
COULD BE BURNED AND YOUR FINGERS COULD
BE TRAPPED AND CRUSHED IN THE HOT
ROLLERS. CLOTHING, JEWELRY AND LONG
HAIR COULD BE CAUGHT IN THE ROLLERS AND
PULL YOU INTO THEM.
Do not operate the Laminator with a damaged power supply
cord or attachment plug, upon occurrence of a malfunction, or
after the laminator has been damaged. Contact GBC’s
Technical Service Department or your dealer/distributor for
assistance.
ADVERTENCIA
Attention
Avertissement
NAVAJA FILOSA.
LAME
SHARP BLADE.
COUPANTE.
Mantener manos y
dedos a distancia.
Keep hands and
clothing away.
Tenir mains et
doigts à l'écart.
Service:
THIS SAFETY MESSAGE MEANS THAT YOU
COULD CUT YOURSELF IF YOU ARE NOT
CAREFUL.
Perform only the routine maintenance procedures referred to in
these instructions
WARNING:
SYMBOL PRECEDES EACH SAFETY
MESSAGE IN THIS INSTRUCTION
THIS
SAFETY
ALERT
WARNING: DO NOT ATTEMPT TO SERVICE
OR REPAIR THE LAMINATOR
MANUAL. THE SYMBOL INDICATES A
POTENTAL PERSONAL SAFETY HAZARD
TO YOU OR OTHERS.
Disconnect the plug from the receptacle and contact GBC’s
Technical Department or your dealer/distributor when one or
more of the following has occurred.
WARNING: DO NOT ATTEMPT TO
SERVICE OR REPAIR THE 1264/1244 WF
LAMINATOR.
•
•
•
•
The power supply cord or attachment plug is damaged.
Liquid has been spilled into the laminator.
The laminator is malfunctioning after being mishandled.
The laminator does not operate as described in these
instructions.
WARNING: DO NOT CONNECT THE
LAMINATOR
TO
AN
ELECTRICAL
SUPPLY OR ATTEMPT TO OPERATE THE
LAMINATOR
COMPLETELY
INSTRUCTIONS.
UNTIL
READ
MAINTAIN
YOU
HAVE
THESE
THESE
INSTRUCTIONS IN
A
CONVENIENT
LOCATION FOR FUTURE REFERENCE.
© 2006 General Binding Corporation
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
This limited warranty shall be void if the laminator has been
misused; mishandled; damaged by negligence, by accident,
during shipment, or due to exposure to extreme conditions;
repaired, altered, moved, or installed by anyone other than GBC
or its authorized agents; or if incompatible film was used.
GBC’s obligation under this limited warranty does not include
routine maintenance, cleaning, adjustment, normal cosmetic or
mechanical wear, or freight charges.
WARRANTY
Limited 90- Day Warranty
GBC warrants to the original purchaser for a period of ninety
days on labor and one year on parts after installation that this
laminator is free from defects in workmanship and material
under normal use and service. GBC’s obligation under this
limited warranty is limited to replacement or repair, at GBC’s
option, of any part found defective by GBC without charge for
material or labor.
Without limiting the generality of the previous paragraph,
GBC’s obligation under this limited warranty does not include:
1. Damage caused to the rollers by knives, razors, or other
sharp tools: by any foreign objects falling into the working
area of the laminator; or by cleaning the laminator with
solutions or materials that harm its surfaces;
THIS LIMITED WARRANTY IS IN LIEU OF ALL
OTHER WARRANTIES EXPRESSED OR IMPLIED.
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ARE EXPRESSLY
EXCLUDED. ANY REPRESENTATIONS OR PROMISES
INCONSISTENT WITH, OR IN ADDITION TO, THIS
LIMITED WARRANTY ARE UNAUTHORIZED AND
SHALL NOT BE BINDING UPON GBC. IN NO EVENT
SHALL GBC BE LIABLE FOR ANY SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
WHETHER OR NOT FORESEEABLE.
2. Damage caused by adhesives; nor
3. Damage caused by lifting, tilting or attempting to position
the laminator other than rolling it on its castors across even
surfaces.
FOR EUROPEAN UNION RESIDENTS ONLY: This
guarantee does not affect the legal rights which consumers have
under applicable national legislation governing the sale of
consumer goods.
SPECIFICATIONS
Operating Speed
0 to 10 fpm (3.0m/min) MAX
320°F (160°C)
Maximum Temperature
Maximum Mounting
Thickness
Main Roller-5/8th in. (15 mm) Max.
Pull Roller-5/8th in. (15mm)
Maximum Film Width
1264WF
61 in. (155. cm.), 62 in. Pressure Sensitive Films
1244WF
42 in. Max paper width. (107 cm.), 42 In. Pressure Sensitive Films.
Dimensions (W x D x H) Unit alone: (Uncrated)
80 in. x 28in. x 51in. (203 cm. x71 cm x 129 cm.)
60 in. x 28in. x 51in. (152 cm. x71 cm x 129 cm.)
1246WF
1244WF
Weight
Unit alone:
1244 WF
275 lbs (125 kg)
600 lbs (272 kg)
1264 WF
Electrical Requirements
Refer to the serial plate located on the rear of the laminator for the specific electrical rating
applicable to the unit. Unit is rated for 220VAC-240AC. Do not exceed 240VAC. For best results it
is recommended that 230VAC be used.
US Models-
CE Models-
230V, 30Amps, 60 HZ. Single Phase. 7000Watts 80.in x 28in. x 51in. (203 cm. x71 cm x 129 cm.)
230V, 15Amps, 50 HZ .Single Phase, 7000 Watts 80.in x 28in. x 51in. (203 cm. x71 cm x 129 cm.)
FCC Class A Notice - Notification pour les Etats-Unis
FCC NOTE
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiated radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at their own expense.
Canada Class A Notice - Avis Canada, Class A
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Modifications
Any modifications made to this device that are not approved by General Binding Corporation may
void the authority granted to the user by the FCC and/or by Industry Canada to operate this
equipment.
Toutes modifications apportées à ce dispositif et non approuvées par General Binding Corporation
annuleront le droit accordé à l'utilisateur par le FCC et/ou par Industrie Canada de faire fonctionner
cet équipement.
© 2006 General Binding Corporation
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
PRE-INSTALLATION
Before a 1264WF/1244WF Laminator can be installed,
ensure the following requirements are met:
1. Are doorways and hallways wide enough for the
laminator to be moved to the installation site?
2. Is there ample room for the laminator?
•
A work area must be established that allows for
operation in both the front and rear of the
laminator and provides space for efficient
material flow.
3. Is the environment appropriate for the laminator?
•
The laminator requires a clean, dust and vapor
free environment to operate properly.
•
Avoid locating the laminator near sources of heat
or cold. Avoid locating the laminator in the
direct path of forced, heated or cooled air.
CAUTION: Air flow can cause uneven
heating / cooling of the rollers and result in
poor output quality.
4. Have you contacted a certified electrician to wire
the receptacle and ensure that adequate power is
being supplied, having the appropriate capacity,
over current protection and safety lockouts
available?
GBC 1264 WF/1244 WF Requires:
•
•
•
230V at 60Hz with 30 amps single phase.
1264WF: Nema 6-30P 30A 230V Receptacle.
1244WF: Nema 6-20P 20A 230V Receptacle.
The machines are supplied with Male Plugs.
INSTALLATION
1. Shipping damage should be brought to the immediate attention of the delivering carrier.
2. With assistance, carefully roll the laminator into position over flat and even surfaces.
3. The laminator should be positioned to allow exiting film to flow freely to the floor or a work table. Accumulation of
laminate immediately behind the laminator as it exits the equipment may cause the film to wrap around the pull rollers,
resulting in a “jammed” condition.
4. Avoid locating the laminator near sources of heat or cold. Avoid locating the laminator in the direct path of forced,
heated or cooled air.
5. Once the laminator has been properly positioned, lock the castors in place. Locking the castors prevent the machine
from rolling during set up, operation or servicing.
6. Connect the attachment plug provided with the laminator to a suitably grounded outlet. Avoid connecting other
equipment to the same branch circuit to which the laminator is connected, as this may result in nuisance tripping of
circuit breakers or blowing fuses.
Note:
Machine must be leveled to ensure best performance. Level the machine by lowering both the main and pull rolls.
Lay a level on top of the main and pull rolls. Then, check level from main roll to pull roll on right and left side of the
roll. Finally, check by placing the level diagonally across lower main to lower pull rolls.
© 2006 General Binding Corporation
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Section 1: Detailed Specifications
Specifications provide all of the technical data for
the Titan 1244WF &1264WF
Description:
•
A high speed laminator for the graphic arts
professional as well as for the manufacturer
who produces promotional pieces in-house. A
new elegant design, low power consumption
and first class safety and quality assurances.
Features:
•
•
•
•
•
•
•
•
•
•
•
•
Roller heating technology
Independent control of each heater
Thermal and cold lamination capabilities
Unique vented cooling system
Mounting capabilities to5/8th in.-15mm.
Easy to use control panel
9 Programmable job settings
LCD temperature displays for each heat roller
Rear out put slitter.
Swing out shafts for ease of loading film.
In-Line slitters.
Accushield capable.
•
Encapsulation-Promotional-materials, posters,
counter cards, POP displays, calendars,
instructional displays, phone & debit cards,
blueprints, menus, maps, flipcharts, etc.
Applications:
© 2006 General Binding Corporation
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Section 2: Consumables
•
•
•
Poly-in films, thermal and PSA films
Poly-out films, thermal and PSA
Accushield
Film Types:
Film Diameters:
•
•
Up to a 7 in. outside roll diameter. (18 cm.)
3 in. core standard. (76 cm.)
Core Size:
Film widths:
1264WF
•
•
61 in. Thermal films (155 cm.)
62 in. PSA (157 cm.)
12444WF
•
•
42 in. maximum paper width (107 cm.)
42 in. PSA films (107 cm.)
Paper widths:
1264WF
•
62 in. Maximum paper width (157 cm.)
42 in. maximum paper width (107 cm.)
12444WF
•
© 2006 General Binding Corporation
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Section 3: Function
•
•
•
•
0-10 fpm (0-6.1mpm)
Speed:
DC Geared Motor
Motor:
Up to 320* F. (160*C)
Operations control panel
Heating Capabilities:
Controls:
Roll Design:
•
•
High release silicone main rollers
High release pull roll
Section 4: Electrical
Requirements:
•
•
230 VAC, 60Hz, Single phase, 30Amps.
230 VAC, 50Hz. Single phase, 20Amps.
•
•
1264 WF:
1264WF CE:
•
•
230 VAC, 60Hz. Single phase, 20 Amps.
230 VAC, 50Hz. Single phase, 20 Amps.
•
•
1244 WF:
1244WF CE:
B.T.U output:
•
•
30708 B.T.U./hour
22519 B.T.U./hour
•
•
1264 WF:
1264WF CE:
•
20472 B.T.U./hour
•
•
1244 WF:
1244WF CE:
© 2006 General Binding Corporation
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Heater Wattage:
•
•
1264 WF:
1264WF CE:
•
•
4500W / Heater
3300W / Heater
•
•
1244 WF:
1244WF CE:
•
3000 W / Heater
Amperage draw:
•
•
•
Drive Motor=3.3 Amps.
Fan Motor=0.5 Amps.
Motors and Heater=25 Amps.
•
1264 WF:
•
1264WF CE:
•
•
•
Drive Motor=3.3 Amps.
Fan Motor=0.5 Amps.
Motors and Heater=13 Amps.
•
•
1244 WF:
1244WF CE:
•
•
•
Drive Motor=3.3 Amps
Fan Motor=0.5 Amps
Motors and Heater=12Amps
D/C Voltage used:
A/C Voltage Used:
•
•
36 VDC Motor Voltage
24 VDC Fan Motor
•
230 VAC Recommended…(Not to exceed
240VAC)
© 2006 General Binding Corporation
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Connectors for 1264 WF
Connectors for 1244 WF
NEMA 6-20 P
NEMA 6-30 P
NEMA 6-20 R
NEMA 6-30 R
© 2006 General Binding Corporation
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Section 5: Dimensions
Weight:
•
•
1264 WF:
1264WF CE:
•
•
Crated: 750 lbs. (340 kg.)
Uncrated: 600 lbs. (272 kg.)
•
•
1244 WF:
1244WF CE:
•
•
Crated: 350 lbs (159 kg.)
Uncrated: 275 lbs (125 kg.)
Dimensions:
•
•
1264 WF:
1264WF CE:
•
•
Crated: 58 in.(H) x 87 in. (W) x 40 in. (D)
147 cm. (H) x 221 cm. (W) x 102 cm. (D)
Uncrated: 49in(H) x 77.25 in.(W) x 25.5 in. (D)
124 cm. (H) x196 cm. (W) x65cm. (D)
•
•
1244 WF:
1244WF CE:
•
•
Crated: 57 in.(H) x 68 in. (W) x 38 in. (D)
145 cm. (H) x 173 cm. (W) x 97 cm. (D)
Uncrated: 49in(H) x 77.25 in.(W) x 25.5 in. (D)
124 cm. (H) x145 cm. (W) x65cm. (D)
Nip Height:
•
35.63 in (91cm.)
© 2006 General Binding Corporation
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Section 6: Know your Laminator
This section is intended to aide the user in becoming more familiar with the 1244 WF & 1264
WF laminators. Refer back to this section if you have questions regarding references to certain
parts of the laminator in this laminator.
1.) Safety Shield
9.) Rewind Clutch Adjustment Knob
10.) Rewind Shaft & Rewind Tube
11.) Rear Slitter
2.) Control Panel
3.) Feed Table
4.) Lower Film Shaft/Unwind Shaft
5.) Upper Film Shaft/Unwind Shaft
6.) Unwind Brake
12.) Power Switch
13.) Foot Pedal
14.) Power Cord
7.) Pressure Plate
15.) Web Clutch
8.) Emergency Stop/E-Stop
16.) Roller Lift Handle/Gap Adjustment Handle
© 2006 General Binding Corporation
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
© 2006 General Binding Corporation
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
© 2006 General Binding Corporation
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Know your Laminator Continued-
1.) Safety Shield:
Operation Manual
8.) Emergency Stop/E-Stop:
•
The Emergency/E-Stops are a safety
feature that allows the operator to stop
the rollers from rotating by depressing
them as needed.
•
The Safety Shield aids in preventing the
operators fingers from becoming
pinched or burned in the heat rollers of
the laminator. With the Safety Shield
raised or removed, the machine goes
into the safety mode that prevents the
run button on the control panel from
starting the rollers to turn. The foot
pedal must be used when the Safety
Shield is raised or removed.
9.) Rewind Clutch Knob:
The rewinder is clutch driven. As you
•
increase the tension on the Rewind
Clutch Knob, the amount of force is
increased and increases the rate/strength
of the rewinder.
10.) Rewind Shaft:
The Rewind Shaft is driven by a clutch
•
2.) Control Panel:
The Control Panel enables the operator
system. The greater you increase the
clutch; the amount of force is increased
and increases the rate/strength of the
rewinder.
•
to control motor run/stop, motor
direction, motor speed, cooling fans, top
temperature, bottom temperature, job
number selection, job programming and
temperature reading.
11.) Rear Slitter:
The Rear slitter is intended to cut the
•
web output from the laminator and
should not be used for any other
purpose.
3.) Feed Table:
The Feed Table supports the product
•
that is to be laminated. It also prevents
full access to the roller nip (where the
upper and lower roller meet) of the
laminator. Because of this, the
laminator has been designed not to
operate when the Feed Table is
removed. Re-install the Feed Table
before attempting to operate the
laminator.
12.) Power Switch:
The Main Power Switch turns the
•
laminator on and off. It supplies power
to the laminator.
13.) Foot Pedal:
The Foot Pedal allows the operator to
•
start and stop the machine without using
the Main Control Panel.
4.) Lower Film Shaft/Unwind Shaft:
•
The Lower Film Shaft/Unwind Shaft
holds the lower film and allows the end
user to apply tension to the web.
14.) Power Cord:
The Power cord comes with the machine
•
and requires certain plug configurations.
Please see the Specs to determine
correct outlet configuration.
5.) Upper Film Shaft/Unwind Shaft:
•
The Upper Film Shaft/Unwind Shaft
holds the Upper film and allows the end
user to apply tension to the web.
15.) Web Clutch:
Use the Web clutch to control tension
•
between the main rolls and the pull
rollers. This will assist the end user in
ensuring good output.
6.) Unwind Brake:
The Unwind Brakes are used to apply
tension to the web.
•
16.) Roll Lift Handle/Gap Adjust. Handle:
7.) Pressure Plate:
The Pressure Plate assists in keeping the
•
Use this Handle to select the proper
settings depending on what application
is to be used.
•
leading edge and the trailing edge of the
print flat when fed into the laminator.
© 2006 General Binding Corporation
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Section 7: Display Control Panel
Stand-by
Pressing STAND-BY will cause the
laminator to go into the AUTO-OFF mode.
The laminator will automatically go into this
mode after sitting idle for an extended
amount of time. When in AUTO-OFF mode
the laminator will no longer continue to heat
the main rollers to save power.
Stand-by
Pressing MEMORY will cause the current
speed and heat settings to be recorded in the
JOB memory location shown on the display.
Jobs
Pressing the up or down arrows will cause
the unit to cycle through stored jobs. Up to
9 separate jobs can be stored. To save a job,
select one of the nine jobs to overwrite.
Then change the heat and speed settings as
required for your application. Once
selected, press the memory button once.
Measure
Press and hold the MEASURE key to
display the current roller temperature.
Cooling
When the COOLING button is pressed the
cooling fans will turn on or off. The
COOLING button will illuminate green
when the fans are on. The fans blow fresh
air on the film web in between the heat and
pull rollers.
Run
When the RUN is pressed the rollers will
begin turning. However, pressing run will
not cause the rollers to turn when any of the
following are true: the Emergency Stop is
engaged, Safety Shield is raised or removed
and/or the feed table is removed.
© 2006 General Binding Corporation
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Display Control Panel-Continued
Top and Bottom Temperature
Use the up or down arrow keys to increase
or decrease the set temperature of the heat
rollers. The temperature shown on the
display is the temperature at which the unit
is attempting to attain. For example if the
unit is set to 200*F even though the actual
roller temperature may be higher or lower.
To view the actual temperature press
MEASURE.
Stop
The STOP button ceases the forward
rotation of the rollers.
Reverse
Pressing the REVERSE button causes the
rollers to turn in the reverse direction. The
rollers will only turn in reverse as long as
the REVERSE button is depressed.
© 2006 General Binding Corporation
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Display Control Panel-Continued
Fig. A
The Temperature displayed in the area
referred to as TOP TEMPERATURE and
BOTTOM TEMPERATURE is the value
that the laminator is attempting to attain.
Pressing the MEASURE button will
momentarily display the actual roller
temperature.
The current speed and job settings are given
on the right side of the display.
The current state of the heat rollers is given
on the lower portion of the display. The unit
will always be in one of three states:
AUTO-OFF, READY, or WAIT.
Fig. B
Auto-Off
In the AUTO-OFF state (also referred to as
Standby) the unit will no longer continue to
heat the main rollers. The unit will go into
this state after a period of inactivity or by
pressing the STAND-BY key. Press the
STAND-BY key to bring the unit out of
AUTO-OFF mode. See Fig. A
Ready
The READY icon will flash when the actual
roller temperature is nearing but not quite
met the target temperature.
Fig. C
The READY icon will be displayed
continually when the actual roller
temperature is within +/- 15* F of the target
temperature entered by the operator. See
Fig. B
Wait
The WAIT icon is displayed when the
actual roller temperature is much higher or
lower than the target temperature entered by
the user. See Fig. C
© 2006 General Binding Corporation
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Section 8: Safety
The 1244Wf & 1264 WF have numerous safety features that will help keep the operator safe
from harm. But for these features to work correctly, the user must become familiar with each of
the safety mechanisms as well as never override a safety feature.
Emergency Stop/E-Stop
Two Emergency Stops (Sometimes referred
to as E-Stops) are located on the 1244 WF &
1264 WF laminators. See the “Know your
Laminator” section for the locations.
Pressing any one of the two Emergency
Stops will immediately stop all roller
motion.
To reset the Emergency Stop, simply rotate
the red top clockwise; this will cause the red
top to pop upward and allow the rollers to
turn again.
Safety Shield
The Safety Shield aids in preventing the
operators fingers from becoming pinched or
burned in the heat rollers of the laminator.
With the Safety Shield raised or removed,
the machine goes into the safety mode that
prevents the RUN button on the control
panel from starting the rollers to turn. The
foot pedal must be used when the Safety
Shield is raised or removed. Use caution
when operating the unit with the shield
removed.
© 2006 General Binding Corporation
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Safety Shield-Continued
To remove the Safety Shield, first raise the
shield and locate the spring hinge pin on the
right side of the shield. Pull the pin to
release the shield from the laminator as
illustrated in the photo.
Feed Table
The Feed Table supports the product to be
laminated. It also prevents full access to the
roller nip (where the upper and lower roller
meet) of the laminator. Because of this the
laminator has been designed not to operate
when the Feed Table is removed. Re-install
the Feed Table before attempting to operate
the laminator.
© 2006 General Binding Corporation
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Section 9: How to Guide
This section discusses how to load film on the unwinds, how to center film, how to select and
change the nip, how to center film, how to select and change the nip, how to use the inline slitters
and rear slitter.
Loading Film
Begin by removing the hinge pin that
prevents the film shaft from swinging
outward.
Swing the film shaft outward as is illustrated
in the photo.
© 2006 General Binding Corporation
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Loading Film Continued
The core chucks need to be adjusted to
match the width of the film that is going to
be loaded on the laminator. To do this, be
gin by removing the rubber o-rings.
Then use the included hex tool to loosen the
setscrews in the core chucks. Note: Do not
remove the setscrews; they only need to
be loosened.
Make the necessary adjustments to the upper
roll of laminate to center it to the Main
Rollers.
Slide the Core Chucks into place and gently
tighten the setscrews to secure the Core
Chuck. The rubber O-Rings can be replaced
to keep the film from moving off center.
Make the necessary adjustments to the lower
roll of laminate to match up with the upper.
Lock the Core Chucks into position and
replace the O-Rings.
© 2006 General Binding Corporation
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Select and Change the Nip
The Roller Handle raises and lowers the
Main Rollers and Pull Rollers
simultaneously. The Roller Handle Guide is
notched with preset nip heights. The Roller
Handle is located on the right side of the
laminator.
Keep hands and fingers clear of the
laminator roller nip when changing the gap.
You can be crushed or burned.
Never leave the rollers in the down position
without rotating. Prolonged contact in one
area can form flat spots on the rollers.
To change the nip opening, pull the handle
away from the notch and move to the
desired setting and secure the handle in the
appropriate notch.
Lift the handle to the top position to open
the rollers.
© 2006 General Binding Corporation
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
In-Line Slitters
The In-Line Slitters allows the operator to
slit the images as they pass through the Main
Rollers and into the Pull Rollers. The
trimmed waste can then be attached to the
Rewinder Tubes and disposed of later.
To engage the In-Line Slitters, simply press
the lever down to expose the blade. Keep
hands and fingers away from the path of the
In-Line Slitters. The blade is extremely
sharp and can cut you.
To disengage the In-Line Slitter blade,
simply push the blade lever up to return the
blade to its original state.
Rear Cut-Off Blade
The Rear Cut-Off Blade is intended to cut
the web output from the laminator and
should not be used for any other purposes.
Stop the laminator before using the Rear
Cut-Off Blade. Moving material can
damage the Rear Cut-Off Blade.
Keep hands and fingers away from the path
of the Rear Cut-Off Blade. The blade is
very sharp and can cut you.
Slide the rear Cut-Off Blade about six inches
into the web. Press and hold down the blade
engage lever. Slide the Rear Cut-Off Blade
from one side to the opposite side then
release.
© 2006 General Binding Corporation
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Section 10: Applications
The 1244 WF & 1264 WF can accommodate Poly-in or Poly-out films. Poly-out means the
adhesive is on the outside of the roll. Each film requires a slightly different loading procedure.
Refer to the Webbing diagrams at the end of this section.
The shiny side of clear film must contact the heating components with the dull sides (adhesive
side) facing out. Use caution when loading Matte or Delustered film since both sides appear
dull.
The top and bottom rolls of laminating film must be of the same width and be present
simultaneously.
Fig. 1A & B
Film Loading & Threading
The top and bottom rolls of laminating film must be of the
same width and be present simultaneously. A Small amount
of adhesive will “squeeze out” during Lamination.
Hardened adhesive deposits can damage the heat rollers.
CAUTION:
Adhesive will deposit on the rollers if:
•
•
•
•
Only one roll is used.
Different widths of rolls are loaded together.
Either roll is loaded adhesive side against a heat roller.
One or both rolls of film are allowed to run completely
off its core.
The adhesive side of the film is on the inner side of the web
(Fig. 1A & B). The shiny side of clear film must contact the
heat rollers. The dull side of the film contains the adhesive.
Use extreme caution when loading delustered (matte) film
as both sides appear dull.
Always change the top and bottom supply rolls at the same
time. Near the end of each roll of GBC laminating film is a
label stating “Warning-End of Roll”. The appearance of
this label on either the top or bottom roll requires that new
rolls of film be installed as soon as the item presently being
laminated completely exits the rear of the laminator.
Fig. 2
1
Do not introduce any additional items into the laminator
when the warning label is visible.
4
To load a roll of film: (Fig.2)
1. Pull the swing out shaft clevis pin up.
2. Swing shaft outward.
5
2
3. Slide the roll of film onto the film shaft ensuring
Adhesive side is out.
6
=
3
4. Push the film shaft back into the film shaft Support
saddle.
5. Push the clevis pin down.
6. Center the roll of film.
© 2006 General Binding Corporation
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Webbing Thermal Film Using Threading Card
Fig.3
CAUTION: The laminator rollers will be hot and
can burn you. For pressure sensitive film (PSA),
refer to the section titled
THERMAL
LAMINATE
WEBBING: USING FILM THREADING CARD FOR
PSA FILM.
1. Turn the Main Power ON
/OFF
to On.
2. Set top and bottom temperature with regards to the
film type used.
3. Ensure no brake tension is applied to the film shafts.
4. Pull the top roll film down under the upper idler bar
and allow to drape over the top heat roller (Fig. 3)
5. Pull the lower film behind the lower idler bar, Lower
the table Pull Film up towards the film draped over the
top heat roller and adhere the Lower Film to the upper
Film (Fig. 4).
Fig. 4
6. Pivot the table back to its feeding position while
ensuring the threading card is on top of the feed table
(Fig. 5).
THERMAL
LAMINATE
7. Use a threading card to push the two materials into the
heat roller nip.
8. Lower the main roller to initial contact with the
threading card.
9. Ensure forward is selected for Motor direction and
Press the Foot Switch
10.From the rear of the machine, guide the web over the
chill idler, if installed, and through the pull rollers.
11.Once the web has entered the pull roller nip, lower the
pull roller nip. Adjust unwind film tension; use as little
tension as possible to get smooth output.
THERMAL
LAMINATE
12.Once the threading card has completely exited the pull
rollers, press the stop button.
13.Now refer to the section entitled START
LAMINATING.
Fig. 5
THERMAL
LAMINATE
THERMAL
LAMINATE
© 2006 General Binding Corporation
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Webbing PSA Film/Mount Adhesive Using Threading
Card
The laminator should be cool to the touch before
Proceeding.
1. Turn the Power ON
/OFF
to On
2. Load the rolls of film as illustrated in (Fig. 6). Ensure
no brake tension is applied to the film shafts.
3. Pull the top roll of film down under the idler bar and
up to the upper front rewind tube.
4. Place one piece of masking tape in the center of the
film and secure to the rewind tube.
5. Make two full wraps around the rewind tube, and then
score the laminate without cutting the release liner.
Pull the laminate down allowing it to drape over the
upper roller (Fig. 6).
Fig. 6
6. Pull the mount adhesive up towards the film draped
over the upper heat roller (Fig.7).
REWIND TUBE
7. Stick the mount adhesive to the exposed adhesive of
the upper role.
PSA
Film
8. Insert the table back to its feeding position while
ensuring the threading card is on top of the feed table
(Fig. 8).
9. Use a threading card to push the two materials through
the heat roller nip
Mount
Adhesive
10.Lower the main heated roller to bring the main roller
into initial contact with the threading card. Ensure
front is selected and press the foot switch.
11.From the rear of the machine, guide the web over the
chill idler, if installed, and through the pull rollers.
Once the web has entered the pull roller nip, close the
pull roller nip –
Fig. 7
12.Press the stop button when the threading card has
completely exited the pull rollers and adjusts the film
web tension using as little tension as possible.
PSA
Film
13.Now refer to the section titled START
LAMINATING.
CHILLED ROLLER
HEAT ROLLER
Mount
Adhesive
Fig.8
© 2006 General Binding Corporation
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Start Laminating
1. At this point you should have your laminator Webbed
with the appropriate material for your application.
2. The feed table should be in the normal operating
position.
3. Close the main and Pull roll nips. Rollers should be
closed.
4. Speed is set to 3 or less and front motor direction is
selected.
5. Press the start button.
6. Set main roller pressure at desired setting for
laminating by turning the roll lift handle.
CAUTION: If using PSA film, an air pocket may result
between the main rollers and pull rollers. Raise the pull
rollers to allow the air Pocket to pass.
Fig. 9
7. Make any necessary film brake tension adjustments,
pull/main roller pressure, and clutch and/ or rewind
brake tension adjustments.
8. Position the item to be laminated on the feed table.
9. Align the leading edge of the item parallel to the heat
roller nip (Fig. 9).
10.With both hands and an outward force push the image
slower than the speed of the rollers into the nip of the
heat rollers (Fig. 10).
CAUTION: Avoid forcing the image into the main
roller nip as this action will cause the corners of the
leading edge to buckle and create a wave.
Fig. 10
© 2006 General Binding Corporation
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Method for Tacking New Film to Existing Film
The following describes a method for loading film whereby
the existing film present on the heat rollers may be used in
place of the threading card to draw the new film through
the laminator. The adhesive of the existing film must be
tacky or liquefied. Leading edges of the new film will be
overlapped onto the tacky adhesive of the old film. The
existing film and the new film will be pulled through the
laminator together.
(1)
(2)
(2)
CAUTION: Do not cut yourself
CAUTION: Be careful not to cut any of the rollers!
.......a PSA film or mount adhesive
1. Cut (1) remaining top film web between the idler bar
and heat roller. Cut (2) the film web between the lower
film supply and the idler bar (Figure 11).
Fig. 11
CAUTION: Be careful not to cut any of the rollers!
2. Remove the feed table down.
3. Do not allow the adhesive side of the film to contact
the heat or pull rollers. Liquefied or tacky adhesive
deposited on heat rollers will require the rollers to be
cleaned per the section tilted.
4. Replace both the top and bottom rolls of film with new
rolls. Ensure the adhesive side is facing out.
5. Pull the film around the idler bars, with the exception
of PSA mounting adhesives without a release liner.
.......a PSA film or mount adhesive
6. Tack the new film to the existing film on the heat
rollers. For PSA film, attach the release liner to the
rewind tube
Fig.12
7. Use the footswitch to advance the film into the heat
roller nip.
8. Observe the film being pulled through the laminator to
assure that the remaining existing film and the new
films are advancing concurrently. Any separation
between the films will require stopping the motor
immediately and the situation corrected.
9. Press STOP once the newly threaded film has
completely exited the pull rollers.
© 2006 General Binding Corporation
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
To Unweb the laminator
Unweb the laminator if you are changing film widths,
cleaning the rollers or have finished using the machine for
the day.
(2)
(1)
CAUTION: Do not cut yourself
1. Using a slitter, cut (1) the output from the web (Fig.
13).
(3)
(2)
2. Cut (2) remaining top film web between the idler bar
and heat roller. PSA film cut the release liner too.
3. Cut (3) the film web between the lower film supply
and the idler bar (Fig. 13).
.......a PSA film or mount adhesive
Fig. 13
CAUTION: Be careful not to cut any of the rollers!
4. Remove the feed table.
5. Gap the main rollers and pull rollers.
6. Carefully grab hold of the web (top and bottom film),
from the back operating position and pull towards you
(Fig. 14).
7. Do not allow the adhesive side of the film to contact
the heat or pull rollers.
PULL WEB
Clearing a Film Jam (Wrap-up)
Film jams (wrap-ups) may occur if the film is loaded
backwards or if the area at which film exits the equipment
is blocked. The film, when jammed, wraps around the heat
rollers or pulls rollers during webbing if webbing, if a
Thread Card is not used.
To clear a jam:
Fig.14
1. Immediately stop the laminator by pressing STOP.
2. Set motor direction to rear.
3. Use the footswitch to reverse the web until the wrap up
is clear.
4. Raise the main roller and pull rollers.
5. Manually guide the web from the main rollers and pull
rollers.
6. Once the film jam has been cleared, lower the main
roller and pull rollers.
7. Refer to the section titled START LAMINATING.
© 2006 General Binding Corporation
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Tips for Pre Coating Boards
MOUNT
ADHESIVE
1. Load the laminator as illustrated in (Fig. 15). Remove
chill idler.
LEADER BOARD
TRAILOR BOARD
2. The width of the roll should not exceed the width of
the board by more than 1/2 in. (1.3 cm).
3. Use a leader board to set the main roller and pull roller
pressure prior to webbing.
BOARDS
4. Use a leader board to start the run and a trailer board to
finish the run.
5. Using the pull rollers will allow you to leave gaps
between boards.
6. If not using the pull rollers, have the boards nearby to
butt end to end during feeding.
Fig. 15
Tips for Mounting Pre Coated Boards
1. Use a leader board to set the main roller pressure prior
to mounting the image.
IMAGE
RELEASE LINER
2. Ensure the chill idler is removed and the rear slitter is
to one side.
3. Do not stop once you have started the mounting
process through the machine. (Fig. 16)
PRE-COATED BOARD
Note: This application can also be performed from the
rear operating position.
Fig.16
Tips for Single Sided lamination
1. Load the laminator as illustrated in Fig. 17.
MOUNT
ADHESIVE
2. Use Kraft paper for one-sided lamination When ever
the items to be laminated are narrower than the film
you are using.
RELEASE LINER FROM PSA FILM
OUTPUT
IMAGE
3. If not using Kraft paper, use a scrap piece to finish the
run or you will have adhesive on your rollers.
4. For high volume runs, use Kraft paper and the lower
rear rewind for roll to roll operation.
KRAFT
PAPER
OPTION
5. Running the web over the chill idler may improve the
Flatness of the output.
6. A little heat, 125 degree F (52 degree C), may help
eliminate silvering effects associated with PSA films.
Fig. 17
© 2006 General Binding Corporation
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Tips for Creating a Decal
1. Load the laminator as illustrated in Fig. 18.
2. The over laminate may be PSA or thermal type.
THERMAL
OR PSA
FILM
3. If using thermal type, pay attention to the Poly-
in/Poly-out rule.
RELEASE LINER FROM PSA FILM
4. Run a test material prior to running the actual image to
ensure flat output.
OUTPUT
IMAGE
5. Use minimal brake tension to achieve quality output.
6. Do not web the PSA mount adhesive around the lower
web idler.
MOUNT
ADHESIVE
Tips for mounting a Decal
1. Use a leader board to set the pull roller pressure prior
to mounting the image.
Fig. 18
2. The image should not exceed the width of the board by
more than 1 in. (2.54 cm) per side.
3. Tack about 1 in. (2.54 cm) of the leading edge of the
decal to the leading edge of the board.
4. When tacking the leading edge, start in the center and
work to the sides.
DECAL
RELEASE LINER
BOARD
5. Use a board that exceeds the size of the decal if
inexperienced in the mounting application.
Note: This application can also be performed from the
front operating position.
Tips for Thermal Encapsulation
1. Load the laminator as illustrated in Fig. 20 Poly-in
film is used for illustration purpose.
Fig.19
2. Refer to section entitled FILM LOADING
THREADING for Poly-out film.
&
3. Always use two rolls of film the same width.
4. Use minimal brake tension to achieve flat output.
THERMAL
FILM
5. Increase speed gradually to maintain the activating
temperature required for the laminate you are using.
IMAGE
OUTPUT
6. Length and width of image, ink coverage and paper
type may affect the temperature and speed
recommended in the SPEED/ TEMPERATURE
GUIDE.
THERMAL
FILM
Fig. 20
© 2006 General Binding Corporation
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Tips for ACCUSHIELD
THERMAL
FILM
1. Load the laminator as illustrated in Fig.21.
IMAGE
2. You must have the Separator bar option to accurately
run this material. See your Sales Rep for ordering the
Separator Bar.
OPTIONAL
SEPERATOR BAR
OUTPUT
3. Set Top Temp to 265 o F* (129* C) and a speed
setting no greater than 4.
4. Liner rewind tension will be greater than normal
operating standard
5. To prevent some adhesive adhering to the rollers, you
may choose to use a roll of craft paper for a Carrier.
KRAFT
PAPER
OPTION
Use the blank space below and blank diagrams to
Fig. 21
Note your tips and web paths for your Special
applications.
TIPS FOR CUSTOM APPLICATION #1 (Fig. 22)
1.
2.
3.
4.
CUSTOM WEB PATH #1
TIPS FOR CUSTOM APPLICATION #2 (Fig. 23)
Fig. 22
1.
2.
3.
4.
5.
CUSTOM WEB PATH #2
Fig. 23
© 2006 General Binding Corporation
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
SPEED / TEMPERATURE CONTROL
This is only a general reference guide. Different settings may be suitable as the warm up time, lamination time and materials
change.
Factors that may affect the speed and temperature parameters;
1. Image length
2. Image width and ink coverage.
3. Ink coverage
4. Paper type
5. Laminate thickness
6. Operating environment
7. Condition of the rollers
8. Line voltage (effects heaters)
9. Using cooling features.
You may have to adjust temperature or speed depending on stock finish, thickness *Turn heat off when not in use.
THE ART OF LAMINATION
BASIC RULES
•
•
Do not attempt to laminate abrasive or metal Objects such as staples, paper clips and glitter, as they may damage the
heat or pull rollers.
Do not force items into the nip area of the heat rollers. An item that is not easily drawn into the laminator by the heat
rollers is probably too thick to laminate.
•
•
Wrinkles may result if an attempt is made to reposition an item once it has been grasped by the heat rollers.
Do not stop the laminator before an item has completely exited the pull rollers. Even a momentary stop will cause a
mark (heat line) on the laminated item.
Good, consistent lamination is a result of combining proper heat, tension and dwell time. Dwell time is controlled by the speed of
the motor and is defined as the amount of time the material to be laminated is compressed between the heat rollers.
As a general rule, thicker items and film need to run at slower speeds because they extract more heat from the rollers at a quicker
rate. Setting the speed control at slower settings gives the laminator longer dwell time thus allowing proper lamination of thick
items. Thinner items, such as standard copier paper (20 lb. bond) and tissue paper, extract less heat from the rollers and can be
run at faster speeds.
FILM TENSION
Proper film tension, known as brake tension, is the minimum amount required to eliminate wrinkles in the finished item. The film
should be taut. A properly adjusted roll of film should not require excessive force to turn by hand.
Film tension should be enough to introduce a minor amount of drag as the film unrolls. Insufficient tension causes wrinkles,
while too much tension causes stretching (necking). Uneven tensions between the top and bottom rolls create curl. Too much
upper tension creates upward curl while too much bottom tension causes downward curl.
Adjustment of the pull roller clutch may be necessary if after adjusting unwind and rewind brake tensions do not improve your
output quality.
© 2006 General Binding Corporation
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
Heat
The “READY” indicator may extinguish if the speed is set
too fast for the material being laminated. Either lower the
speed setting or press STOP and wait until the “READY”
indicator illuminates. Operation of the laminator for more
than thirty minutes at a time may necessitate a lower speed
setting. It is recommended that, during periods of long runs,
the items being laminated are alternated between thick and
thin. Do not combine thick and thin items at the same time,
as this will result in a poor edge seal around the thinner
material. If you are unsure that the laminator is set at the
proper speed for the item to be laminated, run a test piece
(scrap) of the same or similar material through the
Laminator. This procedure is recommended because
rotating the heat roller prior to lamination will more evenly
distribute the heat.
- A -
- B -
Fig. 24
Make speed adjustments if necessary.
Output
1. “D” waves in the image (Fig. 24 A&B).
•
•
Check paper tension.
Paper may be damp or not dry.
2. “D” waves in the laminate (Fig. 24 A&B).
•
•
Check main roller pressure.
Check pull roller pressure.
- A -
- B -
3. Straight waves in output (Fig. 25 A).
•
Check operational settings for materials being
used.
Fig. 25
•
Check clutch tension.
4. Indent waves in output after pull rollers. (Fig. 25 B)
•
•
•
•
Insufficient cooling time.
Output was handled prior to cooling.
Use cooling feature if not on.
Machine was stopped on print.
5. Angled waves in the output. (Fig. 26 A&B)
•
•
•
•
•
Main air Supply setting
Check main Roller Pressure.
Check main roller pressure.
Check pull roller pressure.
Check for Paper Tension.
- A -
- B -
Fig. 26
© 2006 General Binding Corporation
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
MAINTENANCE
Caring For the GBC 2064WF Laminator
GBC offers Cleaning kits as well as Extended Maintenance Agreements.
Contact your local GBC Service Representative or your dealer/distributor for additional information. The only maintenance required by the
operator is to periodically clean the heat rollers and schedule semi annual maintenance checks. The following procedure will help keep the heat
rollers free of adhesive that has been deposited along the edge of the laminating film. Proper alignment of the rolls of film reduces the amount of
“squeeze out”.
WARNING: Do not attempt to laminate adhesives marked “Flammable”.
Do not laminate glitter and/ or metallic items. Damage to the rollers may result.
WARNING: Do not apply any cleaning fluids or solvents to the rollers. Some solvents and fluids could ignite on heated
rollers.
Never clean rollers with sharp or pointed objects.
Hardened adhesive deposits on the rollers can cause damage to the rollers. Rotate the rollers at the lowest speed
setting on the control panel.
CAUTION: THE FOLLOWING PROCEDURE IS PERFORMED WHILE THE LAMINATOR IS HOT. USE EXTREME
CAUTION.
1. Remove the film from the laminator following the Procedure outlined in steps 1 through 6 of the section entitled TO UNWEB THE
LAMINATOR.
2. Preheat the laminator until the “READY” indicator illuminates.
3. Tilt the feed table.
4. Rub the top and bottom heat rollers with a 3M™ Scotch-Brite™ pad. DO NOT USE METAL SCOURING PADS!
5. Use the footswitch to rotate the lower heat/ pull roller to an unclean portion. The upper heat/ pull rollers are free spinning. Continue
this process until the complete surfaces of both rollers are clean.
6. Refer to the beginning of the section entitled OPERATING INSTRUCTIONS to web your laminator.
NOTE: Do not use metal scouring pads to clean the rollers.
© 2006 General Binding Corporation
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
TROUBLE SHOOTING GUIDE
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
The control panel display does not
illuminate when POWER ON/OFF
is in the ON, marked “I”, position
Laminator not connected to
electrical supply
Insert attachment plug into
receptacle
Blown out fuse.
Check fuses.
Heat rollers do not turn when I
Feed table not properly installed.
Tilt feed table and properly replace
it.
Press the RUN button.
Heat rollers only turn if I use the
“Footswitch”.
Pull E-Stop button
Photo eye is blocked.
Pull out on the E-STOP push button.
Disengage the footswitch mode.
Clear nip area.
Laminated items exhibit curling.
Tension between the top and bottom Adjust tension per section FILM
film. Roll is unequal. TENSION.
Tension on top or bottom roll of film Adjust tension per section FILM
is too film is too loose.
Bottom film roll may be improperly
loaded.
TENSION.
Make sure bottom roll of film is
around idler bar and that is the
normal operation position.
Release heat and pull roller pressure,
align the rolls of film.
Adhesive deposited on heat rollers.
Top and bottom film webs not
aligned
Laminate improperly loaded.
Adhesive (matte) side of laminate
film may be against the heat rollers.
Unweb and reload the film properly.
Lower speed setting.
Unsatisfactory adhesion of laminate. Speed setting too fast for type of
material being laminated
Insufficient heat
Wait for “READY” indicator to
appear in the control panel display.
Adhesive side of film must be facing
away from the heat rollers.
Bottom roll of film not threaded
behind the idle bar.
Laminate improperly loaded
Heat rollers require cleaning.
Laminated item unsuitable for
adhesion.
Clean heat rollers per procedure in
section CARING FOR THE GBC
3064 WF LAMINATOR. Item may
be dirty or may have non porous
surface that is extremely difficult to
laminate.
SERVICE AGREEMENT
GBC’s Equipment Maintenance Agreement will insure the quality performance and long life built into your laminator.
A service charge for travel time, labor and parts may be incurred for each out of warranty service call. GBC’s Equipment Maintenance Agreement
Decreases these expenses and protects your valuable investment. GBC offers several types of agreements to suit your needs and budget. To
contact
GBC write to:
GBC NATIONAL SERVICE
ONE GBC PLAZA
IN CANADA:
GBC NATIONAL SERVICE
49 RAILSIDE ROAD
DON MILLS, ONTARIO
M3A 1B3
NORTHBROOK, IL 60062 U.S.A.
General Binding Corporation
One GBC Plaza
Northbrook, IL 60062-4195
®
© 2006 General Binding Corporation
Page 38
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 1264WF/1244WF
Operation Manual
© 2006 General Binding Corporation
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Electro Voice Speaker EVH 1152S 43 User Manual
EXFO Photonic Solutions Div Power Supply IQS 1500 User Manual
Extron electronic Stereo System RGB 109XI User Manual
Fisher Price Baby Toy x3189 User Manual
Freescale Semiconductor Computer Accessories Block Manual User Manual
GE Dehumidifier ADER65LQ User Manual
GE Microwave Oven JES1290SK User Manual
Gemini Musical Instrument PMX 04 User Manual
Gemini Music Mixer BPM1000 User Manual
GE Monogram Washer Dryer WBSR3140 User Manual