I
I
I
I
USB Mass Storage Driver
Exif Viewer
DP Editor
Exif Launcher
Quick Start Guide
Thank you for purchasing these FUJIFILM products.
This Quick Start Guide provides you with a simple summary of how connect your PC
and camera via the USB ports and how to install the software provided in this package
on your personal computer (PC). Read this guide carefully to ensure that you use the
software correctly.
For detailed information on how to use the Exif Viewer and DP Editor software, refer to
the User’s Guide on the enclosed CD-ROM.
E
BB10768-301(1)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. DISCLAIMER OF WARRANTY.
EXCEPT AS PROVIDED IN SECTION 5 HEREIN, FUJI PROVIDES PRODUCT “AS IS” AND
WITHOUT WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED. FUJI SHALL MAKE NO
WARRANTY, EXPRESS, IMPLIED OR STATUTORY, AS TO ANY OTHER MATTERS, INCLUDING,
BUT NOT LIMITED TO NON-INFRINGEMENT OF ANY COPYRIGHT, PATENT, TRADE SECRET, OR
ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY, MARCHANTABILITY, OR FITNESS
FOR ANY PARTICULAR PURPOSE.
IMPORTANT
Be sure to read this page before using the Software.
7. LIMITATION OF LIABILITY.
IN NO EVENT SHALL FUJI HAVE ANY LIABILITY FOR ANY GENERAL, SPECIAL, DIRECT,
INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR OTHER DAMAGES (INCLUDING DAMAGES FOR
LOSS OF PROFITS OR LOST SAVINGS) INCURRED FROM THE USE OF OR INABILITY TO USE
PRODUCT EVEN IF FUJI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
NOTICE
BEFORE OPENING THE PACKAGE OF CD-ROM PROVIDED BY FUJI PHOTO FILM CO., LTD.,
PLEASE READ THIS END USER LICENSE AGREEMENT CAREFULLY. ONLY IF YOU DO
AGREE TO THIS AGREEMENT, YOU WILL BE ABLE TO USE THE SOFTWARE RECORDED
ON THE CD-ROM. BY OPENING THE PACKAGE, YOU ACCEPT AND AGREE TO BE BOUND
BY THIS AGREEMENT.
8. No export.
You acknowledge that neither Software nor any part thereof, will be transferred, or exported to any
country or used in any manner in violation of any export control laws and regulations to which Software is
subject.
9. Termination.
In case you breach any of the terms and conditions hereof, Fuji may immediately terminate this
Agreement without any notice.
End User License Agreement
10.Term.
This Agreement is effective until the date when you cease to use Software, unless earlier terminated in
accordance with Section 9 hereof.
This End User License Agreement (“Agreement”) is an agreement between Fuji Photo Film Co., Ltd.
(“Fuji”) and you, which sets forth the terms and conditions of the license granted for you to use the
software provided by Fuji.
11.Obligation upon termination.
Upon termination or expiration of this Agreement, you shall, at your own responsibility and expense,
delete or destroy immediately all Software (including its copies), Media and Documentation.
The CD-ROM contains third party software. In case a separate agreement is provided by a third
party supplier for its software, the provisions of such separate agreement shall apply to the use of
such third party software, prevailing over those of this Agreement.
12.Governing Law.
This Agreement shall be governed by and construed in accordance with laws of Japan.
1. Definitions.
(a) “Media” means the CD-ROM titled “Utilities for Fujifilm Digital Camera” which is provided to you
together with this Agreement.
(b) “Software” means the software which is recorded on Media.
(c) “Documentation” means the operation manuals of Software and other related written materials which
are provided to you together with Media.
(d) “Product” means Media (including Software) and Documentation collectively.
2. Use of Software.
Fuji grants to you a nontransferable, nonexclusive license:
(a) to install one copy of Software onto one computer in binary machine executable form;
(b) to use Software on the computer onto which Software is installed; and
(c) to make one backup copy of Software.
Do not attempt to play the CD-ROM enclosed with this product on
an audio CD player.
Doing so could damage your hearing or could damage your
a
3. Restrictions.
speakers or headphones.
3.1 You shall not distribute, rent, lease or otherwise transfer all or any part of Software, Media or
Documentation to any third party without Fuji’s prior written consent. You also shall not sublicense,
assign or otherwise transfer all or any part of the rights granted to you by Fuji under this Agreement
without Fuji’s prior written consent.
3.2 Except as expressly granted by Fuji hereunder, you shall not copy or reproduce all or any part of
Software or Documentation.
3.3 You shall not modify, adapt or translate Software or Documentation. You also shall not alter or
remove copyright and other proprietary notices that appear on or in Software or Documentation.
3.4 You shall not, or shall not have any third party, reverse-engineer, decompile, or disassemble
Software.
Please note that this Guide is written on the assumption that you already have a basic
understanding of how to use your PC (personal computer), Windows and Macintosh.
For basic information on using your PC, Windows and Macintosh, refer to the respective
manuals supplied with your PC.
• Microsoft and Windows are trademarks of the Microsoft Corporation of the U.S. registered in
the U.S. and other countries.
Windows is an abbreviated term referring to the Microsoft Windows Operating System.
• Macintosh, iMac, Mac OS and QuickTime™ are registered trademarks of Apple Computer,
Inc.
4. Ownership.
All copyrights and other proprietary rights to Software and Documentation are owned and retained by
Fuji or the third party suppliers as indicated on or in Software or Documentation. Nothing contained
herein shall be construed, expressly or implicitly, as transferring or granting any right, license, or title to
you other than those explicitly granted under this Agreement.
• Adobe Acrobat and PhotoDeluxe are trademarks of Adobe Systems Incorporated of the
U.S.
• SmartMedia™ is a trademark of Toshiba Corporation.
• All other company or product names are trademarks or registered trademarks of the
respective companies.
5. Limited Warranty.
Fuji warrants to you that Media is free from any defect in material and workmanship under normal use for
ninety (90) days from the date of your receipt of Media. Should Media not meet the foregoing warranty,
Fuji shall replace such defective Media with other Media bearing no defect. Fuji’s entire liability and your
sole and exclusive remedy with regard to any defect in Media shall be expressly limited to such Fuji’s
replacement of Media as provided herein.
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows
Introduction
Contents
Software Overview
This section briefly describes the software programs provided on the enclosed
CD-ROM.
IMPORTANT ....................................................................................... 2
Contents ............................................................................................. 4
Introduction........................................................................................ 5
USB Mass Storage Driver
Software Overview ...................................................................................... 5
The USB Mass Storage Driver (USB Driver)
software makes it possible for a digital
camera to operate as a USB-connected
card reader. Installing the driver allows you
to view and copy digital camera image files
on your personal computer (PC).
Installation on a Windows PC........................................................... 6
Pre-installation Checklist ............................................................................. 6
Installing the Software ................................................................................. 7
Installing the USB Driver.......................................................................... 7
Windows 98 ............................................................................................. 8
Windows Millennium Edition.................................................................. 10
Windows 2000 Professional .................................................................. 11
Installing the Enclosed Applications ...................................................... 13
NOTE
The USB Driver does not provide remote
photography functions.
Using the User’s Guide ................................................................... 16
Installation of Acrobat Reader ............................................................... 16
Using the User’s Guide.......................................................................... 16
Exif Viewer
Allows you to list the images on a digital camera or PC, print indexes of the images,
view and print the images, and perform simple image processing operations.
Using the Software on Windows.................................................... 17
Connecting the Camera and PC and Viewing Images .............................. 17
DP Editor
Updating the USB Driver on a Windows PC.................................. 20
Updating the USB Driver for Windows 98 and Windows Me................. 20
Updating the Windows 2000 Professional USB Driver.......................... 20
Allows you to create print ordering information that can be used to obtain prints on
printers that support DPOF (Digital Print Order Format).
QuickTime
Uninstalling the Software on a Windows PC................................. 22
Software used to play back video images shot using a digital camera.
Uninstalling Exif Viewer, DP Editor and Exif Launcher.......................... 22
Exif Launcher (Windows only)
The Exif Launcher software starts up Exif Viewer and displays lists of images when a
digital camera equipped with a USB interface is connected to your PC.
Installation on a Macintosh............................................................. 23
Pre-installation Checklist ........................................................................... 23
Installing the Software ............................................................................... 24
Installing the USB Driver........................................................................ 24
Installing the Enclosed Applications ...................................................... 27
Acrobat Reader
Software used to read the User’s Guide provided on the enclosed CD-ROM.
Using the User’s Guide ................................................................... 28
Installation of Acrobat Reader ............................................................... 28
Using the User’s Guide.......................................................................... 28
Using the Software on a Macintosh............................................... 29
Connecting the Camera and Macintosh and Viewing Images................... 29
Uninstalling the Software on a Macintosh .................................... 31
Uninstalling the USB Driver ................................................................... 31
Uninstalling Exif Viewer and DP Editor.................................................. 31
Troubleshooting .............................................................................. 32
Windows-specific Problems................................................................... 34
Macintosh-specific Problems................................................................. 37
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows
Installing the Software
Installation on a Windows PC
Pre-installation Checklist
Installing the USB Driver
This section describes the setup procedure for using the USB Driver on Windows.
Hardware and software requirements
1. Switch on your PC and start up Windows.
(If you are using Windows 2000 Professional, log
on as an Administrator group.)
To run this software, you must have the hardware and software described below. Check
your system before you begin the installation.
Compatible PCs
: IBM PC/AT or compatible
(models with USB support as standard)
: Windows 98 (including the second edition)
Windows Millennium Edition (Windows Me)
Windows 2000 Professional
2. Double-click “My Computer”.
Operating System
✽
When installation is completed, a new removable disk is added.
(Log on as an Administrator group.)
: 200 MHz Pentium or better
: 32 MB minimum
3. Insert the enclosed CD-ROM into the CD-ROM
drive.
CPU
RAM
Hard disk space
: Amount required for installation: 60 MB minimum
Amount required for operation: 110 MB minimum
: Fujifilm digital cameras equipped with a USB interface
4. Load a card containing photographed images into
the camera, switch the camera on and set it to
Playback mode.
Supported cameras
NOTE
• Connect the PC and digital camera directly using the USB cable. Connecting
via USB hub is not guaranteed.
• USB interface board is not guaranteed.
• Windows 95 cannot be used.
5. Use the USB cable to connect the camera to the
USB port on the PC.
NOTE
• Self-made PC is not guaranteed.
• Connect the cable to the USB port
on the PC. If the cable is connected
via a USB hub, the software may not
operate correctly. If the PC has 2 or
more USB ports, any USB port can
be used.
• Do not use USB drivers other than the USB Driver provided on the camera
software CD-ROM. You must update your software to the USB Driver provided
on the CD-ROM.
Attach the noise suppression core
If a noise suppression core is enclosed,
fit the core to the communications cable
• Push the USB connector in fully to
ensure that the connection is
secure. If the cable is not securely
connected, the software will not
operate correctly. Refer to the
Owner’s Manual supplied with the
camera for details.
Noise
to reduce emissions of unwanted
suppression core
electrical noise. If the cable is already
fitted with a noise suppression core, use
the cable as is.
• To avoid communication errors, use
the USB cable provided in this
package and do not use an
extension cable.
Press until it clicks shut.
✽
See P.10, if you are using Windows Millennium Edition.
See P.11, if you are using Windows 2000 Professional.
✽
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows
9. Select the
\USBDRV\WIN98 folder
Windows 98
6. The “Add New Hardware Wizard” dialog appears.
Click [Next>].
on the CD-ROM drive,
click the [OK] button,
and then click [Next>].
in the “Add New
Hardware Wizard”
dialog box.
NOTE
If this Wizard doesn’t appear, update the
USB driver (See P.20).
TIP
When there is a plus mark “ ” to the left of the Utilities folder, clicking the “
to the left of the folder name opens the folder and shows the folders inside.
”
+
+
10. Check that
USBS04CB.INF has
been detected and then
click [Next>].
7. Select “Search for the best driver for your device
(Recommended)” and click [Next>].
11. When driver installation
is completed, the
dialog shown at right is
appears. Click the
[Finish] button.
8. In the next window, tick “Specify a location” and
click the [Browse…] button.
✽
The dialog shown may differ slightly
on some types of PC.
12. Setup is completed when a new removable drive
icon (the connected camera) appears in the “My
Computer” window.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows
Windows Millennium Edition
Windows 2000 Professional
6. The “Add New
Hardware Wizard”
window opens. Click
the [Next>] button.
6. The “Found New
Hardware Wizard”
window opens. Click
the [Next>] button.
NOTE
NOTE
If this Wizard doesn’t appear, update the
USB driver (See P.20).
If this Wizard doesn’t appear, update the
USB driver (See P.20).
7. When the “Select Other
Driver” window opens,
select USB Mass
7. Select “Search for a
suitable driver for my
device (recommended)”
and then click [Next>].
Storage in the \USBDRV
\WIN98\USBS04CB.INF
line on the CD-ROM
drive and then click the
[OK] button.
8. When driver installation
is completed, the
8. In “Optional search
locations”, tick
screen shown at right
appears. Click the
[Finish] button.
“Specify a location”
and then click [Next >].
9. Setup is completed when a new removable drive
icon (the connected camera) appears in the “My
Computer” window.
✽
The screen shown may differ slightly depending on the type of computer.
9. The dialog box for
specifying the location
appears. Click the
[Browse…] button.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows
10. Select
\USBDRV\WIN2KPRO
Installing the Enclosed Applications
1. Quit any other applications that are running.
Quit all other active applications until no
applications are shown in the taskbar.
on the CD-ROM drive
and click the [Open]
button.
TIP
<To quit an application>
Click the right mouse button on the
application icon in the taskbar. Click “Close”
in the menu that appears to quit the
application. Refer to the instructions
Click one of the icons on the left to
simplify location selection.
Applications that cannot be
closed from the taskbar.
11. Click the [OK] button in
the location
provided with your PC for details.
specification dialog
box.
2. Load the enclosed CD-ROM into the CD-ROM
drive.
Double-click “Utilities (D:)” in the “My
Computer” window.
✽
12. Check that
(Here, “D:” is the designation for the
CD-ROM drive.)
UW2K04CB.INF has
been detected and then
click [Next>].
NOTE
If a “----.dll file not found.” message
appears during the installation, there is
an application (screen saver, etc.)
running in the background that was not
shut down in step 1. Forcibly quit the
application. Refer to your Windows
User’s Guide for information on how to
forcibly quit an application.
13. When driver
installation is
completed, the screen
shown at right
appears. Click the
[Finish] button.
14. Setup is completed when a new removable drive
icon (the connected camera) appears in the “My
Computer” window.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows
Exif Viewer, DP Editor, QuickTime and Exif Launcher are installed sequentially.
To stop the installation process, click the [Cancel] button. The current setup
program stops and installation skips to the next application program.
6. When the DP Editor setup ends, the QuickTime
Setup program starts up.
Proceed with the installation as
directed by the on-screen instructions.
3. Double-click “Viewer” in the CD-ROM window.
When the “Viewer” window appears,
double-click “SETUP.EXE”.
✽
In the “Enter Registration” window,
the software will still be installed if
you enter no information.
7. When the QuickTime setup ends, the Exif
Launcher Setup program starts up.
Click the [Next >] button.
4. The Exif Viewer Setup program starts up.
When the window for selecting the
installation destination appears, check
the destination and then click the
[Next >] button.
Click the [Next >] button. When the
window for selecting the installation
destination appears, check the
destination and then click the [Next >]
button.
Proceed with the installation as
directed by the on-screen
instructions. When Exif Viewer
installation ends, the next setup
program starts up.
8. When the Exif Launcher setup ends, installation is
completed.
5. When Exif Viewer setup ends, the DP Editor Setup
program starts up.
Click the [OK] button. This completes
the installation of all the applications.
Click the [Next >] button. When the
window for selecting the installation
destination appears, check the
destination and then click the [Next >]
button.
✽
DP Editor is a software utility for creating new DPOF files and is based on DPOF
version 1.00. When you are using this software to edit DPOF files that were set
up on a digital camera, some functions may not be available depending on the
software version supported.
✽
Particularly with media containing DPOF settings specified on other brands of
digital camera, you should reset the DPOF settings using the selected digital
camera before using the DP Editor.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows
Using the User’s Guide
To read the User’s Guide supplied on the CD-ROM, you must have Adobe
Systems’ Acrobat Reader installed.
Using the Software on Windows
Connecting the Camera and PC and Viewing Images
✽
Refer to the Owner’s Manual for your camera for information on using the camera.
Installation of Acrobat Reader
1. Start up your PC and double-click the “My
Computer” icon.
1. Switch on your PC and start up Windows.
2. Load the CD-ROM into the CD-ROM drive on your PC.
3. Quit any other applications that are running. See P.13 for information on how to
quit other applications.
NOTE
If another application is running, the “----.dll not found” message may appear and
the software may not be correctly installed.
4. Double-click the “ar40eng.exe” setup program in the “\ACROREAD\ENGLISH”
folder on the CD-ROM.
2. Load a media containing photographed images
into your camera, switch the camera on and set the
Mode dial to “Playback” mode.
5. Proceed with the installation as directed by the on-screen instructions.
Using the User’s Guide
NOTE
1. Load the CD-ROM into the CD-ROM drive on your PC.
The media used should contain images shot using a FUJIFILM camera.
2. When you open the Manual folder in the Viewer folder on the CD-ROM, it
contains the following file. Use Acrobat Reader to view the file.
3. Connect the camera and PC using the USB cable.
When the “Removable Drive” icon appears in the
“My Computer” window, the camera and PC are
correctly connected.
English.pdf: User’s Guide
✽
For easier viewing, copy the English.pdf file onto the hard disk in your PC.
For information on how to use Acrobat Reader, refer to the online guide
✽
provided in the Acrobat Reader Help menu.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows
If Exif Viewer and Exif Launcher are
installed, Exif Viewer starts up and the
window shown here appears.
6. To exit Exif Viewer, select “Exit” from the “File”
menu or click the [Close] button in the main
window.
TIP
✽
For more information on using Exif Viewer or DP Editor, refer to the User’s Guide
• When you install Exif Launcher, it is
registered in the startup menu and is
launched automatically when
Windows starts up.
(PDF document) on the CD-ROM.
7. Check that the camera display indicates that data
access is no longer in progress.
To quit Exif Launcher, click the right
mouse button on the [
] icon in the
On Windows 2000 Professional, click the eject icon
taskbar and select “Exit” from the
menu that appears. The icon will
disappear from the taskbar.
• If Exif Launcher does not run, the Exif Viewer will not start up. Launch Exif
Viewer from the Windows “Start” menu.
Thumbnail display area
[
] on the taskbar when the camera display
indicates that data access is no longer in progress
and remove “USB Mass Storage”.
8. Disconnect the USB cable and remove the
SmartMedia.
If the icon in the figure is shown in the
taskbar, Exif Launcher is running.
NOTE
• Always check that all camera files are closed and that the camera display
indicates that data access is no longer in progress.
Do not disconnect the USB cable or remove the SmartMedia immediately after
the “Copying” message has gone off.
If a large amount of data is being copied, camera access continues for a short
time after the message displayed on the PC has gone off.
4. Thumbnail images for the image data recorded on
the SmartMedia are displayed in the thumbnail
display area.
5. If you double-click a thumbnail image, the image is
displayed in an Image window.
• Refer to the camera Owner’s Manual for more information on the access
display on the camera.
• In Windows 2000 Professional, disconnecting the USB cable without
performing the “Unplug or Eject hardware” procedure can cause the computer
to hang.
To close the image window, use the [Close] button
in the top right corner of the window.
You can also copy the image to your PC desktop
by dragging the thumbnail from the thumbnail
display area and dropping it onto the desktop.
NOTE
Do not perform the operations listed below when a camera file is open and the
camera display indicates that data access is in progress. Performing any of these
operations could corrupt the data on the media or damage the media itself.
Switch the camera off/Touch any of the camera control buttons/
Disconnect the USB cable/Remove the media/Open the media cover/
Remove the camera batteries
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows
Updating the USB Driver on a Windows PC
Update the USB Driver in the following situations:
NOTE
If you cannot find USB Mass Storage in the “USB Controller” list, look under
“Other devices”.
(1) When you want to upgrade the driver version
(2) When you have installed the driver but the software does not run
8. Select the “Driver” tab and click the [Update
driver…] button. This launches the Upgrade Device
Driver Wizard.
Updating the USB Driver for Windows 98 and Windows Me
1. Switch on your PC and launch Windows 98 or
Windows Me.
9. Select “Display a list of the known drivers for this
device so that I can choose a specific driver” as
the search method and click the [Next>] button.
2. Insert the CD-ROM provided into the CD-ROM drive.
3. Open the “My Computer” window, double-click
“UNIN_FUM.EXE” in the “\USBDRV\WIN98\UNINST”
folder on the CD-ROM and remove the installed
driver.
NOTE
When the dialog box opens, “Search for a suitable driver for my device
(recommended)” is selected. Change this selection to “Display a list of the known
drivers for this device so that I can choose a specific driver.
NOTE
Close all files when removing drivers.
10. In the device driver selection window, select USB
Mass Storage in the “Models:” field and click the
[Have Disk…] button.
4. Install the new driver (See P.7).
Updating the Windows 2000 Professional USB Driver
11. The installation specification dialog box (Install
from floppy disk) dialog box appears. Select
\USBDRV\WIN2KPRO on the CD-ROM drive and
click [OK].
1. Switch on your PC and launch Windows 2000
Professional.
2. Insert the CD-ROM provided into the CD-ROM drive.
TIP
3. Load a media containing photographed images
into the camera and switch the camera on.
Click the [Browse…] button to simplify the selection.
4. Use a USB cable to connect the camera to the USB
port on the PC.
12. When the device driver selection window reappears,
click the [Next>] button.
5. Open the Control Panel, click “System” and open
the System Properties dialog box.
13. When the Upgrade Device Driver Wizard reappears,
click the [Next>] button.
6. Select the “Hardware” tab and click the [Device
Manager] button.
14. The Upgrade Device Driver Wizard completion
screen appears. Click the [Finish] button to
complete the driver upgrade.
7. Click “Universal Serial Bus Controller” in the
Device Manager window, then click the right
mouse button on “USB Mass Storage” and select
“Properties” in “Action” menu.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Macintosh
Uninstalling the Software on a Windows PC
Installation on a Macintosh
Pre-installation Checklist
Uninstalling Exif Viewer, DP Editor and Exif Launcher
You can automatically uninstall these application programs using “Add/Remove
Programs” in the Control Panel.
Hardware and software requirements
To run this software, you must have the hardware and software described below. Check
your system before you begin the installation.
NOTE
• Use this procedure only when the installed software is no longer required or
when software installation fails.
• Always quit Exif Viewer, DP Editor and Exif Launcher before beginning
uninstallation.
✽
✽
Compatible Macs
: Power Macintosh G3 , PowerBook G3 , Power Macintosh G4,
iMac or iBook
✽
( Models with a USB port as a standard feature)
• Uninstall Exif Launcher before uninstalling Exif Viewer.
Connecting the camera to your PC with only Exif Launcher left installed could
cause problems.
Operating System
RAM
Hard disk space
: Mac OS 8.5.1 to 9.0
: 32 MB minimum (64 MB recommended)
: Amount required for installation: 60 MB minimum
Amount required for operation: 110 MB minimum
: Fujifilm digital cameras equipped with a USB interface
1. Switch on your PC and start up Windows.
Supported cameras
NOTE
2. Open the “My Computer” window and double-click
“Add/Remove Programs” in the Control Panel.
• Connect the Macintosh and digital camera directly using the USB cable.
Connecting via USB hub is not guaranteed.
• USB interface board is not guaranteed.
3. Select the application to be uninstalled.
The “Add/Remove Programs Properties” window appears. Select the program to
be deleted (Exif Viewer, Exif Launcher or DP Editor) and click the [Add/Remove]
button.
Attach the noise suppression core
If a noise suppression core is enclosed,
fit the core to the communications cable
4. Confirm the deletion.
Noise
to reduce emissions of unwanted
suppression core
A confirmation dialog box appears. Uninstallation cannot be cancelled once it has
been confirmed in this dialog box. Check the details carefully.
electrical noise. If the cable is already
fitted with a noise suppression core, use
the cable as is.
5. UninstallShield starts up.
When uninstallation ends, click the [OK] button.
Press until it clicks shut.
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Macintosh
Installing the Software
3. Check whether File Exchange is active.
Installing the USB Driver
To use a media that is supported by the camera, the File Exchange utility supplied
with Mac OS must be running. Select the Extensions Manager in the Control
Panels and check that the File Exchange check box is ticked. If not, click in the
box so that an [X] appears and then restart your Macintosh.
1. Switch on your Macintosh and start up Mac OS.
2. Version verification and updating for iMac.
If you are using an iMac, an update may be necessary to ensure that USB
operates stably. Updating is not required on other models. Use the procedure
below to check whether updating is required.
1 Select “Apple System Profiler” from the Apple menu.
2 Select the “Devices and Volumes” tab.
3 The circled part shows the USB Manager version.
4. Copy the driver to the Extensions folder.
1 When you load the enclosed CD-
ROM into the CD-ROM drive, the
CD-ROM icon appears on the
desktop.
If you are using USB Manager 1.0.1, your iMac must be updated. If the version is
1.1, no update is needed.
2 Double-click the CD-ROM icon,
open the “USB Mass Storage
Driver” folder and then the
“English” folder. The English folder
contains 2 files:
G Updating iMacs
Update your iMac using the “iMac Firmware Update” or “iMac Update” iMac
updater files, which can be downloaded from the Apple Computer internet web
with Macintosh computer magazines. Refer to the explanatory text files provided
with updater for instructions on how to update your iMac.
“USB04CB_StorageShim” and
“USB04CB_StorageDriver”. Copy
these 2 files to the Extensions
folder inside the System folder on
the startup disk.
3 Select “Restart” from the “Special”
menu to restart your Macintosh.
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Macintosh
5. Connect the camera to your Macintosh.
Installing the Enclosed Applications
1 Load the media into the camera, switch the camera on and set the Mode dial to
1. When you load the enclosed CD-ROM into the
CD-ROM drive and double-click the CD-ROM icon,
the “Exif Viewer” folder appears.
“Playback” mode.
NOTE
Some cameras support storage media other than SmartMedia.
2. Copy the “Exif Viewer”
folder to your hard
disk.
2 Use the USB cable to connect the camera to the USB port on your Macintosh.
NOTE
• Connect the cable to the USB port
on your Macintosh. If the cable is
connected via a USB hub, the
✽
The “Exif Viewer” folder contains
“Exif Viewer” and “DP Editor”.
software may not operate correctly.
If the PC has 2 or more USB ports,
any USB port can be used.
• Push the USB connector in fully to
ensure that the connection is
secure. If the cable is not securely
connected, the software will not
operate correctly. Refer to the
Owner’s Manual supplied with the
camera for details.
• To avoid communication errors, use
the USB cable provided in this
package and do not use an
extension cable.
3. Open the English folder
in the QuickTime 4 folder
and double-click the
“QuickTime Installer”
icon. Installation begins.
✽
In the “Registration” window, the
software will still be installed if you
enter no information.
4. When installation is completed, restart your
Macintosh.
This completes the installation.
3 Setup is complete when a new removable disk icon
✽
DP Editor is a software utility for creating new DPOF files and is based on DPOF
(the connected camera) appears on the desktop.
version 1.00. When you are using this software to edit DPOF files that were set
up on a digital camera, some functions may not be available depending on the
software version supported.
✽
Particularly with media containing DPOF settings specified on other brands of
digital camera, you should reset the DPOF settings using the selected digital
camera before using the DP Editor.
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Macintosh
Using the User’s Guide
To read the User’s Guide supplied on the CD-ROM, you must have Adobe
Systems’ Acrobat Reader installed.
Using the Software on a Macintosh
Connecting the Camera and Macintosh and Viewing Images
✽
Refer to the Owner’s Manual for your camera for information on using the camera.
Installation of Acrobat Reader
1. Start up your Macintosh.
1. Switch on your Macintosh.
2. Load the CD-ROM into the CD-ROM drive on your Macintosh.
2. Load a media containing photographed images
into your camera, switch the camera on and set the
Mode dial to “Playback” mode.
3. Quit any other applications that are running. In the Applications menu, click on
any program other than the Finder and select “Quit” from the File menu.
NOTE
4. Double-click the “English Reader Installer” setup program in the “English”
folder in the “Acrobat Reader 4” folder on the CD-ROM.
Some cameras support storage media other than SmartMedia.
5. Proceed with the installation as directed by the on-screen instructions.
3. Use the USB cable to connect the
camera to your Macintosh. If a
removable disk icon appears on the
desktop, the camera and Macintosh
are correctly connected.
Using the User’s Guide
1. Load the CD-ROM into the CD-ROM drive on your Macintosh.
2. When you open the MANUAL folder in the Exif Viewer folder on the CD-ROM,
it contains the following file. Use Acrobat Reader to view the file.
4. Double-click the Exif Viewer icon to
start up the software. The main
window shown below appears.
English.pdf: User’s Guide
✽
For easier viewing, copy the English.pdf file onto the hard disk in your
Macintosh.
✽
For information on how to use Acrobat Reader, refer to the online guide
<Main window>
provided in the Acrobat Reader Help menu.
5. When you select (click)
“Untitled” disk →
“DCIM” → “100_FUJI”
from the list displayed
on the left side of the
main window,
thumbnails of the
images recorded on the
media are displayed in
the thumbnail display
area on the right side of the main window.
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Macintosh
Uninstalling the Software on a Macintosh
NOTE
6. When you double-click a thumbnail image directly,
the image is displayed in an Image window.
The Image window closes when the Close box in
the main window is clicked.
Use this procedure only when the installed software is no longer required or
when software installation fails.
Uninstalling the USB Driver
You can also copy an image to the hard disk by
selecting the thumbnail image dragging it onto the
desktop.
First, check that the digital
camera is no longer
connected. Then open the
Extensions folder in the
System folder on the hard
disk and move the
“USB04CB_StorageShim”
and
“USB04CB_StorageDriver”
files to the Trash.
NOTE
Do not use the camera while it is being accessed by the PC.
Do not perform any of the following operations during camera access as this
could result in damage to the data on the media or damage to the media itself:
- Switch the camera off
- Touch any of the camera operation buttons
- Disconnect the USB cable
- Remove the media
- Open the media cover
- Remove the camera batteries
Then, restart your Macintosh and select “Empty
Trash” from the Special menu.
7. Select “Quit” from the File menu or click the Close
box to exit Exif Viewer.
✽
For more information on using Exif Viewer or DP Editor, refer to the User’s Guide
Uninstalling Exif Viewer and DP Editor
(PDF document) on the CD-ROM.
Quit Exif Viewer and DP Editor and move the Exif
Viewer and DP Editor files to the Trash. Then select
“Empty Trash” from the Special menu.
8. Drag the removable disk icon on the desktop to the
Trash or select the icon and then select “Eject”
from the Special menu in the menu bar at the top
of the window.
9. When the remove allowance displayed, disconnect
the USB cable and remove the media.
NOTE
• Removing the media or switching off the camera without “ejecting” the
removable disk icon could damage the media or cause your Macintosh to hang.
• If you are using a media that was formatted on the camera and you replace a
folder on the media with a folder with the same name on your hard disk, the
files may be corrupted. Delete the folder on the media or change the folder
name before copying the data.
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If problems arise and the USB Driver is not running correctly, check the items
listed below.
I (Mac) Is the USB Driver active?
Solution: Select “USB04CB_StorageShim” and “USB04CB_StorageDriver” in the
Extensions Manager and restart your Macintosh.
The camera and PC are connected but no removable disk icon is
displayed.
The PC hangs when I access the media.
I Is the camera switched on?
Solution: Switch the camera on. Refer to the Owner’s Manual supplied with the
I (Win) When opening the Device Manager, there is a yellow “!” mark next to the
driver in “Universal Serial Bus controllers”.
Solution: You are using a driver or camera that prevents the driver for the Universal
camera for details.
Serial Bus controllers from operating. Check your PC setup.
I Is the media loaded in the camera?
Solution: Load a media into the camera. Refer to the Owner’s Manual supplied with
the camera for details.
I Is the camera set to USB connection mode?
Solution: Some cameras have to be set to a particular mode (eg. Playback mode) for
USB connection. Refer to the Owner’s Manual supplied with the camera for
details.
I Is the USB connector cable connected to the camera and the PC?
Solution: Check that one end of the cable is plugged into the camera and the other
end into the PC.
I (Win) When opening the Device Manager, there is a yellow “!” mark next to USB
Driver.
Solution: You are using a driver or camera that prevents the USB Driver from
I (Win) Are you using a compatible operating system?
Solution: Only use the USB Driver provided on the camera software CD-ROM with
compatible operating systems.
operating. Check your PC setup.
I (Win) Is the USB Driver running?
I (Mac) If you are using an iMac, have you updated the iMac?
Solution: It may be necessary to update your iMac. (See P.24.)
Solution: Click “System” in the Control Panel, select the Device Manager tab and
check the USB Driver. If the driver is marked with a yellow “!” or a red “x”,
upgrade the USB Driver.
I (Mac) Is the USB Driver software installed?
Solution: Install the USB Driver software on your PC. For instructions on installing
the USB Driver, see P.24.
My camera will no longer play back image files.
I Did you rename any files or folders inside the DCIM folder?
Solution: Change the file or folder names in the DCIM folder back to the original
names.
I Did you replace an image file inside the DCIM folder?
Solution: Do not replace image files in the DCIM folder.
I (Win) If you are using Windows 2000 Professional, are you logged on as an
Administrator group?
Solution: Log on as an Administrator group.
I (Mac) Are you using Mac OS 8.5.1 or later?
Solution: Upgrade your system software to Mac OS 8.5.1 or later.
I (Mac) If you are using an iMac, have you updated the iMac?
Solution: It may be necessary to update your iMac. (See P.24.)
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
When I install the driver, the “Could not find a driver for this
device” message appears.
Windows-specific Problems
The camera is connected to my PC but the driver installation will
not start.
I The installer cannot read the device driver due to a problem with your PC
setup.
Solution: Select “\USBDRV\WIN98” on the CD-ROM drive.
I Is the camera switched on?
Solution: Switch the camera on. Refer to the Owner’s Manual supplied with the
When I install the driver, the “Could not find UMAS04CB.INF”
message appears.
camera for details.
I Is the camera set to USB connection mode?
I Did you specify the driver folder correctly?
Solution: For Windows 98 or Windows Me, specify \USBDRV\WIN98\USBS04CB.INF.
Solution: Some cameras have to be set to a proper mode (eg. Playback mode) for
USB connection. Refer to the Owner’s Manual supplied with the camera for
details.
For Windows 2000 Professional, specify \USBDRV\WIN2KPRO\UW2K04CB.
INF.
I Is the USB cable connected to the camera and the PC?
Solution: Check that one end of the USB cable is connected to the camera and the
When I connect the camera to my PC, the “Add New Hardware
Wizard” appears.
other end to the PC.
I Are you using a compatible operating system?
I Is the USB Driver installed?
Solution: Install the USB Driver software as directed by the on-screen instructions.
Solution: The USB Driver is not supported by Windows 3.1 or earlier, Windows CE,
Windows 95 or Windows NT 4.0 or earlier. Use a compatible operating
system.
When I double-click the removable disk icon, “The device is not
ready” error message appears.
I If you are using Windows 2000 Professional, are you logged on as an
Administrator group?
Solution: Log on as an Administrator group.
I Is the media loaded in the camera?
Solution: Load a media into the camera. Refer to the Owner’s Manual supplied with
I Are the USB functions active?
the camera for details.
Check
: Click “System” in the Control Panel, select “Device Manager” and check
“Universal Serial Bus controllers”.
A warning message appeared when I removed the media from the
camera.
Solution 1: If “Universal Serial Bus controllers” is not displayed, the USB functions is
disabled. Refer to the User’s Manuals supplied with your PC for details of
how to enable the USB functions.
Solution 2: If the driver is marked with a yellow “!” or a red “x”, USB Driver is not
running. Upgrade the USB Driver.
Solution: This procedure may corrupt the data on the media or damage the media
itself. Close all the camera files and wait until the camera display indicates
that data access is no longer in progress before removing the media.
When I disconnect the cable connecting the PC to the camera
and double-click the removable disk icon, a message appears
and the window does not open or the images on the media are
not displayed correctly.
I Is another USB removable drive connected?
Solution: Some USB removable drives do not operate correctly if other USB
removable drives are being used at the same time. Disconnect all the
connected USB removable drives and then connect the camera.
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
My PC does not shut down correctly.
Macintosh-specific Problems
I Some PCs will not shut down correctly while the FUJIFILM Digital Cameras is
This message appeared when I connected the camera to my
Macintosh.
still connected to the USB interface.
Solution: In future, use the correct procedure to disconnect the USB cable
✽
connecting the FUJIFILM Digital Cameras to your computer before quitting
Windows.
See page 19 if you are using Windows 2000 Professional.
I Is the USB Driver installed?
Solution: Install the driver on your
✽
Macintosh.
I want to stop the Exif Viewer from launching automatically.
When I connected the USB cable, Mac OS displayed the “Initialize
disk?” message.
I If you use the procedure below to remove Exif Launcher, Exif Viewer will no
longer launch automatically.
Solution: Restart your PC and hold down the [Shift] key as soon as the wallpaper
appears.
I Is the media formatted?
Solution: Disconnect the USB cable from the camera, insert the media into the
camera and format the media. Refer to the Owner’s Manual supplied with
the camera for details.
Do not release the [Shift] key until the wallpaper and all your icons have
appeared to show that startup has finished.
Click the [Start] button and select [Programs]-[Startup]-[Exif Launcher] from
the “Start” menu. Click the right mouse button on [Exif Launcher] and
select “Remove” from the pop-up menu.
I The Macintosh cannot recognize the media because File Exchange is disabled.
Solution: Enable File Exchange. See P.25 for details.
As of the next time you start up your PC, Exif Launcher will no longer
launch automatically.
I The media size is not supported by File Exchange and cannot be used on the
Mac OS.
Solution: Use a different media.
A warning message appeared when I removed the media from the
camera.
Solution: This action can damage the data on the media or damage the media itself.
Before removing the media, select the disk and then select “Eject” from the
Special menu. Alternatively, drag the disk icon to the trash.
A warning message appeared when I disconnected the USB
cable from the camera.
Solution: This action can damage the data on the media or damage the media itself.
Before disconnecting the USB cable from the camera, select the disk and
then select “Eject” from the Special menu. Alternatively, drag the disk icon
to the trash.
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
|