50W
BRE
UNLIMITED REBATE PLANER
WITH 3 BLADES & REMOVABLE DRUM
3BVSIPCF INSTRUCTION MANUAL
Code: 3BVSIPCF
Date: 080605
Black
Cyan
Magenta
Yellow
Edition: 07
Op: DJ
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Description of symbols
Your new GMC power tool will more than satisfy
your expectations. It has been manufactured under
stringent GMC Quality Standards to meet superior
performance criteria.
The rating plate on your tool may show symbols.
These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years
of dependable service.
Double insulated for additional protection.
CAUTION. Carefully read through this entire Instruction
Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
Conforms to relevant standards
for electromagnetic compatibility.
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance, and
dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
Specifications
Voltage:
230-240V~50Hz
750W
5000 – 15,500min-1
Power Input:
Variable Speed:
Blades:
Environmental protection
3 Reversible slither blades
65Mn standard
Recycle unwanted materials instead
of disposing of them as waste. All tools,
hoses and packaging should be sorted,
taken to the local recycling centre and
disposed of in an environmentally safe way.
Planing Width:
82mm (3 1/4")
0 – 3mm (0 – 1/8")
Yes
Depth of Cut Range:
Left or Right Chip Exit:
Bevelling V Grooves:
Gear Casing:
1
Magnesium
Automatic
3.9 kg
Parking Stand:
Net Weight:
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Personal safety
General safety rules
a. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
WARNING. Read all instructions. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. The term “power tool” in all of
the warnings listed below refers to your mains operated
(corded) power tool or battery operated (cordless)
power tool.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
Save these instructions
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
c. Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools with
your finger on the switch or plugging in power tools that
have the switch on invites accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adaptor plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Ensure your mains supply voltage is the same as your
tool rating plate voltage.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
• After long working periods, external metal parts and
accessories could be hot.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
• If possible, always use clamps or a vice to hold your work.
• Always switch off before you put the planer down.
• Do not force the planer: let the tool do the work at
a reasonable speed. Overloading will occur if too
much pressure is applied and the motor slows resulting
in inefficient planing and possible damage to the
planer motor.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
• Always use a dust extraction system where possible.
• Rags, cloths, cord, string and the like should never be
left around the work area.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
• Remove all nails, screws and other objects from the
workpiece. You can damage the blade and the tool by
cutting into a nail or other foreign object. It can also
present a safety hazard.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result in
a hazardous situation.
• Handle the blades very carefully.
• Be sure that the blade installation bolts are securely
tightened before operation.
• Always wear eye and ear protection and use a
dust mask.
5. Service
• Hold the tool firmly with both hands.
• Keep hands away from rotating parts.
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
• Before using the tool on an actual workpiece, switch
on and let it run for a while. Watch for vibration or
wobbling that could indicate poor installation or a
poorly balanced blade.
Additional safety rules for electric planers
• Wait for the cutter to stop before setting the tool down.
An exposed cutter may engage the surface leading to
possible loss of control and serious injury.
• Make sure that a blade is not in contact with the
workpiece when you switch the machine on.
• Fully unwind cable drum extensions to avoid
potential overheating.
• Wait until the blades attain full speed before cutting.
• Operate the tool at least 200mm away from your face
and body.
• When an extension cable is required, you must ensure
that it has the right ampere rating for your power tool and
is in safe electrical condition.
• Always switch off and wait until the blades have come to
a complete standstill before attempting any adjustments.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• Never stick your finger into the chip chute. Shavings may
jam in the chute when cutting damp wood. Clean out the
chips with a stick but only when the tool has been turned
off and unplugged from the power point.
The manufacturer shall not be liable for any changes made
to the tool nor for any damage resulting from such changes.
Even when the tool is used as prescribed it is not possible
to eliminate all residual risk factors. The following hazards
may arise in connection with the tool’s construction
and design:
• Do not leave the machine running unattended. Operate
the tool only when controlled by both hands.
• When leaving the planer, switch off and set it with the
front base up on a wooden block so that the blades are
not in contact with anything.
• Damage to hearing if effective hearing protection is
not worn.
• Always remove the plug from the mains socket before
making any adjustments or maintenance, including
changing the blades and adjusting the depth of cut.
• Always change the three blades at the same time,
otherwise the resulting imbalance will cause vibration
and shorten the blade and tool life.
• Contact with the blades.
WARNING. Before connecting a tool to a power source
(mains socket power point receptacle, outlet, etc.) be sure
that the voltage supply is the same as that specified on the
nameplate of the tool. A power source with a voltage greater
than that specified for the tool can result in serious injury to
the user, as well as damage to the tool.
• Reaching under the base whilst the tool is running and
making contact with the blade.
• Kickback of workpiece and parts of workpiece.
• Blade fracture.
• Catapulting of faulty pieces from the blade.
If in doubt, do not plug in the tool. Using a power source
with a voltage less than the nameplate rating is harmful to
the motor.
Contents of carton
The GMC 3BVSIPCF Planer is supplied with the following
accessories as standard:
The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual will
be considered a case of misuse. The user and not the
manufacturer shall be liable for any damage or injury
resulting from such cases of misuse.
• 2 Sets of blades (1 fitted and 1 additional)
• Parallel fence
• Blade wrench
• Barrel allen key
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this Manual. All persons who use
and service the machine have to be acquainted with this
Manual and must be informed about its potential hazards.
Children and frail people must not use this tool. Children
should be supervised at all times if they are in the area in
which the tool is being used. It is also imperative that you
observe the accident prevention regulations in force in your
area. The same applies for general rules of occupational
health and safety.
• Spare drive belt
• Dust extraction adaptor
• Dust bag
Unpacking
Due to modern mass production techniques, it is unlikely
that your GMC Power Tool is faulty or that a part is missing.
If you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Know your product
1. On/Off trigger switch
2. Lock off button
3. Depth adjustment dial
4. Main handle
5. Fixed bail handle
6. Dust/Chip extraction port
7. Parallel fence attachmen
8. Dust diverter guide switc
9. Fitted reversible blades
10. Blade barrel
9
11 10 22
25
17
16
18
20
1
2
27
23
11. Clamping screws
12. Front shoe extension
13. Fixed rear base
14. Parallel fence guide
15. Shavings adapter tube
16. Shavings collection bag
17. Spanner
18. Rear parking foot
19. Variable speed setting
20. Power ON indicator neon
21. Drum spindle lock
22. Drum guard
4
24
8
5
3
6
13
23. Drum guard release lever
24. Power cord
25. Allen key
26. Sanding barrel
15
27. Spare drive belt
7
12
26
19
21
14
Additional sanding drum sold separately
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Loosen and unscrew the hex head screw
by rotating the allen key anti-clockwise.
Replacing/removing
and installing planer blades
CAUTION. Always ensure that the tool is switched off
and unplugged from the power supply before installing or
removing planer drum.
Your planer is fitted with a removable drum feature for a
quick drum change, allowing you to safely install a set of
blades that may be suitable for you application. The planer
comes with an additional set of sharp blades.
Note: Always completely remove the planer drum prior to
installing new planer blades. For you own safety, it is not
recommended to remove the planer blades while the drum
is still installed in the planer.
5. When the hex head screw has been removed continue to
remove the two flat washers. Now that the barrel is free
proceed to extract it out of the planer body by pulling it
towards you. Then follow on and remove the blades.
CAUTION: Always ensure that the tool is switched off
and unplugged from the power supply before installing or
removing blades. Your planer is fitted with reversible blades.
Blades can be reversed when blunt. After both sides of the
blade have been used, they should be discarded.
Removing the planer barrel
1. Place the planer on its side so that the motor is facing down.
2. Raise the drum guard (22) (by
pressing on the lever) so that
the hex head screw located on
the blade barrel is exposed.
Insert the short end of the
supplied Allen key into the
head screw.
Removing planer blades
1. Secure the blade drum by
placing the drum into a vice
and have one blade (9)
accessible facing up in the vice.
Note: It is recommended that
you place padding around the
drum – like a cloth when putting
it in the vice.
3. Press the drum spindle lock
button (21), and rotate the
barrel until it is locked into place. Hold in the lock off
button until the barrel has been completely removed.
2. Using the supplied spanner
(17), loosen the three clamping
screws. Slide the planer blade
from the slot in the blade barrel
in which it is retained.
CAUTION. The blades are very sharp. Take care when
handling them.
Note: The blade barrel has two lock out positions.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Now that the blade slot in the blade barrel (10) is empty
you can proceed to either turning over the existing planer
blade or install a new planning blade by following the
instructions.
4. Loosen the vice and rotate the planer barrel and
move onto the next planer blade, repeating the above
blade removal and installation process for the remaining
two blades.
Installing planer blades
5. Once the new blades have been installed remove
blade barrel from vice and continue onto reinstalling
the planer drum.
1. The blades are reversible as
they have a cutting edge on
both sides. If a blade is worn
or damaged, the blade can
be removed and put the other
way around. Either turn the
existing planer blade (9) over
or replace it if required.
CAUTION. When installing blades, first clean out all chips
or foreign matter adhering to the blade barrel (10) and the
blades themselves. Use blades of the same dimensions
and weight, or the barrel will oscillate and vibrate causing
poor planing action and possibly a machine breakdown.
Tighten the clamping screws (11) carefully when attaching
the blades to the planer. A loose clamping screw could
be extremely dangerous. Regularly check to see they are
tightened securely.
2. Slide the good blade face up onto the blade support
block of the blade barrel.
Note. If a blade is damaged, it can be replaced without the
need to replace the other two blades. When blades are
worn, they must be replaced as a set of three to prevent
unbalanced operation with consequential dangerous
vibration and possible damage to the tool.
It is essential that the blades sit square in the slot and that
they are fully inserted prior to tightening the clamping screws.
If the blades protrude or are not square, they could hit the
casing with serious risk to the operator and others in the vicinity.
Correct setting
• Correct setting
Note. Ensure that the blades are positioned such so that
they are flush with the rebate side of the base to enable
correct rebating.
CAUTION. The blades must
not protrude out from the base
rebate side. This may cause an
injury and break the guard. There
has to be enough clearance so
that the blades do not touch the
drum guard in use.
1
3
2
(a)
(b)
• Clean smooth cut.
Note: The ridge along the blade
should be on the blade face on the opposite side of the
clamping screws.
• Nicks in surface – as caused by the edge of one or all
blades not being parallel to the rear base line.
3. Tighten the clamping screws, ensuring that they are
tightened evenly in the following manner.
(a)
(b)
Tighten the two outside clamping screws snug tight,
then the middle screw.
Working in the same order, fully tighten all three screws.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Hand screw the hex head screw clockwise to close the
gap between the washers and hex head screw.
• Gouging at start – as caused by the edge of one or all
blades not protruding enough in relation to the rear
base line.
7. Once the screw has been hand tightened, use the Allen
key (25) to further tighten until the barrel is secured.
8. Release the spindle lock and close the drum guard.
Your power tool is now ready to recommence planing again.
(a)
(b)
Note: Blades must be set correctly or the workpiece will end
up rough and uneven. The blades must be mounted so that
the cutting edge is absolutely level. i.e. Parallel to the surface
of the rear base. Refer to the Correct blade setting section
in this instruction manual prior to planing when installing new
planer blades or a new planing barrel configuration.
• Gouging at end – as caused by the edge of one or all
blades protruding too far in relation to the rear base line.
(A) front base (moveable shoe)
(B) rear base (stationary shoe)
Reinstalling the planer barrel
1. Place the planer on its side.
2. Raise the drum guard.
Removing the planer barrel
and installing a sanding barrel
Note. Sanding drum sold separately.
Your planer has been fitted with a removable drum feature
for an additional sanding drum, this allows you to convert
your planer into a drum sander with ease, by following the
below instructions:
3. Slide the planer barrel into the
housing, lining up the blade
barrel with the spindle.
Note: Dependent on what sanding grit barrel has been
selected, the powertool can be used when sanding wood,
metal, plastic and similar materials. It is used mainly for
quickly removing a large amount of material. Do not use
this sander for sanding steel or magnesium.
4. Press in the drum spindle
lock button (21) and rotate the
barrel (10) until the barrel is
locked into place. Continue to
hold the in the lock in button
until the new barrel has been
tightly secured.
CAUTION. Always ensure that the tool is switched off
and unplugged from the power supply before installing or
removing the drum.
Note: the blade barrel
has two lock out positions.
Removing the planer barrel
Note: Refer back to earlier in the Instruction Manual for
detailed information (page 8).
5. Re-insert the large washer,
adjusting its position so that
the spindle end passes through
the centre. Now insert the
smaller washer followed by the
hex head screw.
1. Place the planer barrel on its side.
2. Raise the drum guard so that the Hex Head screw
located on the blade barrel is exposed.
WARNING. If the larger washer is
not correctly orientated the drum
cannot be firmly secured.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press in the drum spindle lock
button and rotate the barrel
(10) until the barrel is locked
into place. Hold in the lock in
button until the new barrel has
been completely removed.
Parallel fence guide
CAUTION. Always ensure that the tool is switched off
and unplugged from the power supply before making
adjustments or installing or removing blades.
1. Fit the fence guide (14) to the
base by screwing the knobs
(7) into the fixing points.
Note: The blade barrel has two
lock out positions.
2. When set at right angles to
the planer base, the fence
provides a guide to help
control the planing action.
Installing a sanding barrel
Note. Sanding drum not supplied.
1. Place the planer on its side.
2. Raise the drum guard.
Note. The fence can be fitted to
either side of the base.
3. Slide a sanding barrel back
into the housing; lining up the
sanding barrel with the spindle.
Note. The angle graduations marked on the fence are for
indicative purposes only.
4. Press on the drum spindle lock
(21) and rotate the barrel (10)
until the barrel is locked into
place. Continue to hold in the
lock in button until the new
Adjusting the depth of cut
CAUTION. Always ensure that the tool is switched off
and unplugged from the power supply before making
adjustments or installing or removing blades.
1. Rotate the depth adjustment knob (3) clockwise for a
deeper cut and anti-clockwise for a shallower cut.
barrel has been tightly secured.
Note: The drum spindle lock
2. The numbers on the ring
under the depth adjustment
knob indicate the depth of cut.
Example, when “1” is next
to the pointer on the front of
the planer, the depth of cut is
approximately 1mm.
has two lock out positions.
5. Re-insert the large washer,
adjusting its position so that the
spindle end passes through the
centre. Now insert the smaller
washer followed by the hex
head screw.
3. If it is necessary to accurately
determine the depth of cut,
plane a scrap piece of wood,
measure the difference in
thickness and adjust the
setting if necessary.
WARNING. If the larger washer
is not correctly orientated the
drum cannot be firmly secured.
6. Hand screw the hex head
screw clockwise to close the
gap between the washers and
hex head screw.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching on and off
Planing
CAUTION. Before plugging the machine into the power
socket always check that the on/off trigger switch (1) and
lock-off button (2) work properly.
1. Extract the front shoe extension by placing your thumb in
the groove on top of the front shoe extension while at the
same time gripping the shoe and pulling it forward.
1. Plug in the machine and grip
the tool with your index finger
on the on/off trigger switch
(1) and thumb on the lock-off
button (2).
2. Push lock-off button (2) in with
thumb and press in the on/off
trigger switch (1) with the rest
of your hand gripping the tool.
You can release the finger hold
on the lock off button (2) once the planer has started.
2. Place the front shoe extension
(12) flat on the workpiece
surface without the blades
making any contact with the
workpiece.
3. To stop the tool, release the thumb hold on the on/off
button (1).
4. In order to restart the machine,
it is necessary to operate both
the lock-off button (2) and the
on/off switch (1).
3. Switch on the tool and wait for
the blades to reach full speed.
4. Move the tool gently forward,
applying pressure on the front
of the tool, using your hand
on the secondary handle (5)
at the start of planing and
pressure at the rear of the tool,
using your hand on the main
handle (4) towards the end of
the planing stroke.
CAUTION. Please note that the
planer blades continue to turn
for some time after switching off
the planer. Wait until the motor
has completely stopped before
setting down the tool to prevent damage
to the planer blades or the surface.
If you wish to rest the planer on its side, do not rest it on the
side with the vents to prevent dust or chips from getting into
the motor.
Note. Do not apply excess
pressure on unit when front extension shoe extends, this
could possibly damage the shoe.
5. When the planer is not to be used for a short period, set
the depth control knob to the “P” position and rest the
front of the planer on a block of wood to keep the base
clear of the surface. Ensure that the rear parking foot is
down to protect blades.
Note: As a feature this planer has been fitted with a larger
front handle than traditional electric planers. The front bail
handle provides for good ergonomics when planing, allows
the operator to balance and control the unit with ease and
makes vertical planing a dream.
5. Push the planer beyond the edge of the workpiece
without tilting it downwards.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Note. Planing is easier if you incline the workpiece slightly
away from you so that you plane “downhill”.
Note. For planing it is recommended to have the planer
running at full speed to obtain the cleanest possible planing
result. When sanding the speeds should be set from 1-6.
On maximum speed the unit will vibrate and be hard to hold.
6. The rate of planing and the depth of cut determine the
quality of the finish. For rough cutting, you can increase
the depth of cut, however to achieve a good finish you
will need to reduce the depth of cut and advance the tool
more slowly.
Chamfering
1. To make a chamfered cut as shown in fig.1, First align the
“v” groove (fig.2) in the front base (12) of the planer with
the corner edge of the workpiece.
CAUTION. Moving the machine too fast may cause a poor
quality of cut and can damage the blades or the motor.
Moving the machine too slowly may burn or mar the cut.
The proper feed rate will depend on the type of material
being cut and the depth of the cut. Practice first on a scrap
piece of material to gauge the correct feed rate and the
cut dimensions.
1
2
CAUTION. Always use two hands to hold the planer.
CAUTION. Where possible, clamp the workpiece to
the bench.
7. In between operations, you can rest the planer on a flat
surface with the blade protection foot (18) hinged down
to support the planer so that the blades are kept clear of
the surface.
2. Run the planer along the corner edge.
Fig. 1. Chamfered edge.
Fig. 2. Aligning the “v” groove
Full/Unlimited rebating
Note. When planing the dust might settle in the front
extension shoe and block its movement. To clean out the
dust loosen the two clamping blocks and use a brush or
compressed air blower.
The GMC planer comes with an unlimited rebating
capability. When operating the planer to achieve a full
rebate the following instructions must be adhered for the
safety of the tool operator.
CAUTION. Wear eye protection if using a compressed air
blower.
When you want to achieve a full rebate follow the steps 1
to 3.
Adjusting the speed
The speed of the drum can be
adjusted to suit the material
being planned or sanded.
To adjust the speed, move the
variable speed control (19) until
you are satisfied that the speed
is what you need for the job in
hand. On the speed control dial (19); 1 is the lowest speed
and ‘max’ is the highest speed.
1. Using you thumb from the hand located on the front bail
handle (5) select the drum
guard release lever (23) and
push it forward. By pushing
forward on the drum guard
release lever (23) the blade
guard (22) will raise and
expose barrel/drum (10),
enabling full unlimited rebating.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Run the planer along the
workpiece.
WARNING. Variable speed should be 1-6 when sanding.
Never on ‘Max this will cause it to vibrate and possibly
cause an injury.
3. Once you have finished
planing the section take the
pressure off the drum guard
release lever (23) and make
sure that the drum guard (22)
is full covering the barrel/drum.
CAUTION: Do not raise the drum guard if it is not
performing a full/unlimited rebate application.
WARNING: If the drum guard does not completely close
immediately stop using the power tool and have the unit
serviced by a qualified service agent. If you use the product
with a defective blade drum guard the manufacturer will not
be held liable for any damage or personal injury caused.
2. Check to make sure that the planning depth adjustment
dial (3) is set to the ‘O’ height setting.
3. Bring the sander onto the work
piece and apply light pressure.
4. Pull up the trigger switch (1)
and set the variable speed at
1-6 before moving it across
the work.
5. Sand with the grain, in parallel
overlapping strokes.
6. Adjust the variable speed dial as required.
7. To remove paint or smooth very rough wood, sand across
the grain in 45º in two directions, and then finish the
parallel with the grain.
Note: The workpiece will automatically raise the blade drum
guard automatically when rebating up to 45mm (the height
of the pivot point of the drum guard) timbers.
Note. Do not apply too much force on the lever, excess
pressure may cause blade guard to break.
8. Lift the sander off the work before switching it off.
9. Remember to keep your hands away from the moving
sanding barrel, as it will continue to move for a short
time after the machine is switched off.
Sanding
Note. Sanding drum not supplied.
Dependent on what sanding grit barrel has been selected,
the powertool can be used when sanding wood, metal,
plastic and similar materials. It is used mainly for quickly
removing a large amount of material. Do not use this sander
for sanding magnesium or steel.
10. Wear safety goggles, a dust mask and earmuffs.
11. Use coarse grade to remove rough finishes, Medium
grade to smooth the work and Fine grade to finish it off.
It is best to make a trial run on a scrap piece of material
to determine the optimum grades of belt for a particular
job. In order to take full advantage of sanding function,
always purchase good quality sanding barrels.
Note: When sanding ensure that the depth adjustment dial
is set on the ‘O’ setting.
To achieve the best sanding result with this power tool the
following instructions and tips should be adhered to.
1. Prior to commencing the sanding application,
ensure that the sanding barrel
Selecting the right grade of sanding barrel
Different grades of sanding barrels can be purchased from
your local hardware store. Typical grades are Coarse (40
grit), Medium (80 and 100 grit) and Fine (120 Grit).
is in good condition and fixed tightly.
Note: After sanding with a barrel sander, an orbital sander
should be used to give a better surface
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Shavings extraction
Maintenance
1. Connect the shavings adaptor
tube (15) to the dust/chip
extraction port (6).
WARNING. Always ensure that the tool is switched off and
the plug is removed from the power point before making any
adjustments or maintenance procedures.
2. The adaptor tube (15) can be
installed to allow shavings to
flow either to the left or to the
right of the workpiece.
Regularly check that all the fixing screws are tight. They
may vibrate loose over time.
Cleaning
1. Keep the tool’s air vents unclogged and clean at all times.
3. A workshop dust extraction
2. Remove dust and dirt regularly. Cleaning is best done
with compressed air or a dry, soft to medium brush like a
paint brush.
system or a household vacuum cleaner can be connected
to the adaptor tube (15) for the efficient removal of dust
and shavings permitting a safer and cleaner working
environment, need to add dust extraction tube.
CAUTION. Wear protective goggles when cleaning the tool.
3. Re-lubricate all moving parts at regular intervals.
4. Never use caustic agents to clean plastic parts.
Drive belt replacement
CAUTION. Always ensure that the tool is switched off
and unplugged from the power supply before making
adjustments or installing or removing blades. Also ensure
planer is in park and during blade replacement keep hands
well away from the blade barrel area. It is also suggested
that you wear leather gloves to change the belt in case you
make contact with the blades.
CAUTION. Do not use cleaning agents to clean the plastic
parts of the tool. A mild detergent on a damp cloth is
recommended. Water must never come into contact with
the tool.
Ensure the tool is thoroughly dry before using it.
Power cord maintenance
If the supply cord needs replacing, the task must be carried
out by the manufacturer, the manufacturer’s agent, or a
power tool repair centre in order to avoid a safety hazard.
1. To replace the drive belt first take out the five cross-head
screws that secure the drive belt cover on the left-hand
side of the planer as viewed from the rear.
2. Remove the damaged belt and use a soft brush to clean
the pulleys and the surrounding area.
Note. Wear eye protection when cleaning out the pulley area.
3. With the four continuous “v” profiles on the inside, place
the new belt over the bottom pulley.
Half fit the other end of the belt on the top pulley then roll
the belt in place whilst turning the pulley.
4. Check that the belt runs evenly by manually turning the belt.
5. Replace the cover and the five fixing screws.
6. Replace the electrical plug and run the planer for a
minute or two to make sure that the motor and belt are
operating correctly.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GMC customer assist
If your product needs repairing or you simply need help
or advice, please contact us on our Customer Assist Line
1300 880 001 (Australia) or 0800 445 721 (New Zealand).
For prompt service we suggest you log your service request
access to the Internet, please contact our service department
on 1300 880 001 (Australia) or 0800 445 721 (New Zealand).
7am –7pm, 7days a week (AEST).
Please note that if repair is required, you must
provide a valid original purchase receipt.
You will need the following details at hand to log your service request;
Personal details: First & Last name, address, pick up address,
contact phone numbers, email address
Product details: Product number, date of purchase, retailer bought from,
State & postcode, receipt number, reason for the request,
copy of official purchase receipt
Attach your purchase receipt and save with this Manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
|