Use & Care
sGM Cooktops
For Use With:
SGM304, version
SGM364, version
SGM365, version
SGM464, version
SGM464GG, version
SGM466, version
t a b l e o f C o n t e n t s
Important Safety InStructIonS................................................1-2
cooktop featureS ..................................................................3-4
cooktop operatIonS ...............................................................4-5
care and cleanIng..................................................................6-7
Before you call for ServIce....................................................8
product Warranty....................................................................9
Part No. 65140 Rev. E
Download from Www.Somanuals.com. All Manuals Search And Download.
IMportant safety InstrUCtIons
Installer: Please leave this guide with this appliance.
Consumer: Please read and keep this Use & Care Manual for
DANGER
future reference. This guide provides proper use and maintenance
information. Keep this guide and the sales receipt and/or
cancelled check in a safe place for future reference. Proof of
original purchase date is needed for warranty service.
WARNING – NEVER use this appliance as a space heater
to heat or warm the room. Doing so may result in carbon
monoxide poisoning and overheating of the oven.
This appliance is equipped with a three-prong grounding plug
for your protection against possible electrical shock hazards. It
must be plugged into a grounding receptacle. Where a standard
two-prong wall receptacle is encountered, it is the personal
responsibility and obligation of the customer to have it replaced
with a properly grounded three-prong wall receptacle. Do not
under any circumstances, cut or remove the third (ground)
prong from the power cord. Do not use an adapter plug. Do
not use an extension cord. Do not use a Ground Fault Circuit
Interrupter.
If you have any questions, call:
Dacor® Customer Service
1-800-793-0093 (U.S.A. and Canada)
Monday — Friday 7:30 am to 4:00 pm Pacific Time
Have complete model and serial number identification of your
cooktop ready. These numbers are found on a serial plate,
located_________________. Record these numbers below for
easy access.
Power supply cord with
three-prong grounding plug
Model Number ________________________________________
Serial Number ________________________________________
Date of Purchase______________________________________
For service and warranty information, see page 9.
In our continuing effort to improve the quality and performance
of our appliances, it may be necessary to make changes to the
appliance without revising this guide.
Grounded type wall
receptacle (ground fault
circuit not allowed)
What You Need to Know About Safety
Instructions
Warning and Important Safety Instructions appearing in this guide
are not meant to cover all possible conditions and situations that
may occur. Common sense, caution and care must be exercised
when installing, maintaining or operating an appliance.
Always contact the manufacturer about problems or conditions
you do not understand.
Safety Symbols, Words, Labels
DANGER
DANGER – Immediate hazards which WILL result in severe
personal injury or death.
WARNING
WARNING – Hazards or unsafe practices which COULD result
in severe personal injury or death.
CAUTION
CAUTION – Hazards or unsafe practices which COULD result
in minor personal injury or property damage.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMportant safety InstrUCtIons
WARNING
To reduce risk of fire, electric shock, serious injury or death when using your cooktop, follow these basic precautions,
including the following:
What to Do:
13. Always light each burner prior to placing a utensil on the
1. Begin by ensuring proper installation and grounding of
burner grate. Also, turn the control knob to the “off” position
the appliance by a qualified technician according to the
before removing a utensil from the burner grate.
accompanying Installation Instructions. Have the installer
14. Always clean the cooktop cautiously. If using a damp sponge
show you where the fuse or junction box is located so that
or cloth, wait until the cooktop has cooled sufficiently to
you know how and where to turn off power. Also, have the
prevent steam burns. Also, some cleaners can produce
installer show you the location of the gas supply. If you
harmful or unpleasant fumes if applied to hot surfaces.
smell gas, do not use the cooktop. Immediately turn off the
15. Keep any ventilation filters clean to avoid grease fires.
gas supply at the shut off valve, disconnect electrical power
16. Always set utensils gently onto the grates and center them
to the unit at the fuse or junction box and contact the gas
so that they are well-balanced.
supplier or qualified appliance technician.
ꢀ. Ensure that the cooktop is used only by those individuals
17. Always keep the cooktop surface clean and dry.
who are able to operate it properly.
What Not to Do:
3. Use the cooktop only for cooking tasks expected of a home
1. Do not leave children alone or unattended in the area where
appliance as outlined in this manual.
the cooktop is in use. Never allow children to sit or stand
4. Properly clean and maintain as recommended in this
on any part of the cooktop. Do not let children play with the
manual, cleaning only the parts listed.
cooktop.
5. Use only dry potholders to avoid steam burns when
ꢀ. Do not store items of interest to children above the cooktop.
removing hot cookware.
Children could be burned or injured while climbing on the
6. In the event that a burner flame goes out and gas escapes,
appliance.
open a window or door. Wait at least 5 minutes before
3. Do not wear loose or hanging apparel while using the
attempting to use the cooktop.
cooktop.
7. Select utensils of the proper size, material and construction
4. Do not repair or replace any part of the cooktop unless
for the particular type of cooking being done. Select utensils
specifically recommended in literature accompanying this
that are large enough to contain food without boil-overs or
appliance. All other service should be referred to a qualified
spill-overs. Choose pans with easily grasped handles that
technician.
will stay cool while cooking. Do not use utensils with loose
5. Do not use water on grease fires. A violent steam explosion
handles. Avoid using pans that are too heavy to lift safely.
may result. Smother any flames with a lid, cookie sheet or
Use cookware only for its intended purpose. Certain types of
flat tray. Flaming grease can be extinguished with baking
glass, ceramic, and earthenware utensils are suitable for use
soda or a multi-purpose chemical or foam extinguisher.
only in an oven and not in cooktop applications.
6. Do not allow potholders to touch gas burners. Do not use a
8. When cooking, set the burner controls so that the flame
towel or bulky cloth as a potholder.
heats only the bottom of the utensil and does not lick at the
7. Do not block or obstruct the holes beneath the control
sides of the utensil.
knobs. Blocking these holes may affect burner operation and
9. When deep fat frying, be certain that the pan is large enough
may result in a hazard.
to contain the desired volume of food without overflow
8. When using the cooktop, do not touch the grates, burner
caused by bubbling of the fat. Never leave a deep fat fryer
caps, burner bases, or any other parts in proximity to the
unattended. Avoid deep fat frying of moist or frost-covered
flame. These components may be hot enough to cause
foods. Foods with high water content may cause spattering
burns.
or spilling of the hot fat. Heat fat slowly and stir together any
9. If the cooktop is near a window, do not use long curtains as
combinations of oils and fats prior to applying heat. Utilize
a window treatment. They can blow over the cooktop and
a deep fat frying thermometer to avoid heating the fat to
create a fire hazard.
temperatures above the flash point.
10. Do not cover the burners and grates with anything except
10. Always turn pan handles to the side or back of the cooktop.
properly selected utensils. Decorative covers should not be
Do not turn handles towards the room where they are easily
used.
hit. Handles should not extend over adjacent burners.
11. Do not heat unopened food containers such as baby food
11. Always check the positions of the control knobs to make
jars and cans. Pressure build-up may cause the container to
sure the cooktop is off when you are finished cooking.
burst and cause injury.
1ꢀ. Before performing any service, turn off the gas supply by
1ꢀ. Do not use abrasive or caustic cleaners or detergents on
closing the gas shut-off valve and turning off the electrical
this appliance, as these may cause permanent damage. Do
power supply.
not use aerosol cleaners, as these may be flammable or
cause corrosion of metal parts.
13. Do not use or attempt to use this appliance in the event of a
power failure.
SAvE ThESE INSTRUCTIONS
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooktop featUres
12,500 BTU
8,500 BTU
sealed bUrners
On SGM304 and SGM364 Cooktops, there are a total of four
burners, including one burner rated at a maximum output of
14,000 BTU/HR, one burner rated at a maximum of 1ꢀ,500 BTU/
HR and two burners rated at a maximum output of 8,500 BTU/HR.
The knobs are grouped in twos. The front two knobs operate the
front two burners, and the rear two knobs control the two rear
burners.
Gas
Grill
Knob
8,500 BTU
12,500 BTU
8,500 BTU
14,000 BTU
SGM464GG
Top View
brass bUrner rInGs
All burners are attached to the cooktop by retaining nuts. Gaskets
around the undersides of the burner bases ensure that the
burners are sealed, thereby preventing any liquid spills from
entering the cooktop chassis. All spills remain on the surface of
the cooktop.
14,000 BTU
8,500 BTU
SGM304
Top View
On the SGM365 Cooktop, there are a total of five burners,
including one burner rated at a maximum output of 14,000 BTU/
HR, two burners rated at a maximum of 1ꢀ,500 BTU/HR and two
burners rated at a maximum output of 8,500 BTU/HR. The knobs
are positioned to correspond with the burner layout.
8,500 BTU
12,500 BTU
12,500 BTU
SGM Burner Assembly
sMart-flaMe
Each burner ring features Smart-Flame. When oriented properly
by the burner ring positioning tabs, Smart-Flame prevents direct
flame impingement on the fingers of the porcelain grate. This
reduces temperatures on the grate and improves flame and
performance characteristics, as well as increasing longevity of the
porcelain enamel coating on the grate.
14,000 BTU
8,500 BTU
SGM365
Top View
On the SGM466 Cooktop, there are a total of six burners,
including two burners rated at a maximum output of 14,000 BTU/
HR, one burner rated at a maximum of 1ꢀ,500 BTU/HR and three
burners rated at a maximum output of 8,500 BTU/HR. The knobs
are grouped in threes. The front three knobs operate the front
three burners, and the rear three knobs control the three rear
burners.
bUrner IGnItors & perMa flaMe
A burner igniter is located on each gas burner base. When a
control knob is rotated more than 90˚ counterclockwise, on the
SGM models, all ignitors will spark simultaneously, but only the selected
burner will ignite. Additionally, due to the Perma-Flame reignition
feature, the ignitors will spark automatically if a flame should blow
out or be severely distorted by a draft or by a cooktop ventilation
system. Burner ignitors must always be kept clean and dry to
function properly. Dirty or wet ignitors will result in constant
sparking, even if there is a flame present.
8,500 BTU
12,500 BTU
8,500 BTU
14,000 BTU
8,500 BTU
14,000 BTU
SGM466
Top View
On the SGM464GG Cooktop, there are a total of five burners,
including one burner rated at a maximum output of 14,000 BTU/
HR, one burner rated at a maximum of 1ꢀ,500 BTU/HR, two
burners rated at a maximum output of 8,500 BTU/HR and one
burner rated at a maximum of 9,300 BTU/HR (gas grill burner).
The front two knobs operate the front two burners, and the center
knob controls the gas grill.
Smart-Flame Burner Ring Notches
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooktop featUres
knobs and spIll proteCtor rInGs
The control knobs provided with this cooktop are designed for
ease of use and longevity. The “D” shaped design of the knob
shaft ensures proper orientation when re-installing the knob.
The SGM knobs have a clearly defined chamfer to make setting
the desired heat an easy task. Beneath each knob, a spill
protector ring is inserted into the opening in the cooktop. These
rings prevent liquid spills from entering the chassis beneath the
cooktop and show heat control information. The control knobs and
spill protectors are made of a composite plastic material that is
resistant to staining.
See “Operating the Control Valves” for further information.
sGM464GG Gas GrIll (barbeCUe)
The all gas grill location on the SGM464GG has a 9,300 BTU
burner that is set into the grease control box just above the
removable drip tray. Just above the u-burner is a heat control
channel insert and on top of that sits a porcelain coated grill. The
center control knob operates an automatic perma-flame ignition
system for the single U-shaped burner.
Gas Grill Assembly
Cooktop operatIon
Utensils will affect the overall safety and performance of cooktop
cooking, so it is important to select them carefully. An improperly
selected utensil will not cook efficiently or evenly. For best results,
follow these guidelines:
Logo on Front
Knob Only
seleCtInG the proper Cookware
Low
Position
Off Position
1. Use medium to heavy gauge metal cookware with flat and smooth
bottoms for greatest efficiency.
ꢀ. Use utensils with tight fitting lids to retain heat, odors, and steam.
Area of
Operation
Knob Position
Indicator
(Polished Surface)
before CookInG
Ensure that the cooktop has been installed by a qualified
individual who has tested the operation of the cooktop in
accordance with the Installation Instructions. The brass burner
rings, burner caps, grates, knobs, and spill protectors must be in
place for the cooktop to operate properly. All cooktop components
must be clean. Be certain that the gas and electrical power
supplies to the cooktop are operational. Read this Use and Care
Manual in its entirety prior to operating the cooktop.
Burner
Designation
Light & High
Position
SGM Burner Control Valve
WARNING
Do not touch any burner cap, burner base, or ignitor while the
ignitors are sparking, as an electrical shock could result.
operatInG the Control ValVes
Indicating marks have been placed on the SGM spill ring below
each control knob to clearly identify the burner controlled by each
knob. The burner being controlled is indicated by a flame icon,
while adjacent burners are illustrated by gray ovals.
IMPORTANT:
1. If the gas does not ignite within four seconds, turn off the valve.
Allow at least two minutes for any gas to dissipate, then repeat
the lighting procedure.
2. Burner ignitors must always be kept clean and dry to function
properly. Due to the Perma-Flame™ reignition feature, dirty or
wet ignitors will result in constant sparking, even if there is a
flame present. Additionally, ignitors will spark automatically
if the flame is distorted by a draft or by a cooktop ventilation
system. Eliminate the draft or reduce the ventilation blower
speed in this case.
To light a particular burner, press down on the corresponding
control knob, then immediately rotate the knob counterclockwise
from the “OFF” (Ø) position to the “HIGH” position (the thickest
part of the flame indicator line). All ignitors will spark
continuously until the gas ignites on the selected burner.
4. When the cooktop is cool and/or more than two burners are in
use, the ignitors may continue to spark if the control knob is set
to the “LOW” position. This is normal until the burner warms up.
The tendency to spark under these conditions can be reduced
by operating the burner at a higher flame setting for a short
Once the burner is lit, reduce the flame height if desired by
rotating the control knob further counterclockwise, then place
the utensil on the grate. The flame indicator lines indicate
progressively lower flame height as the lines get thinner.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooktop operatIon
be reduced by operating the burner at a higher flame setting for
a short period of time (normally 60 seconds or less), then
adjusting the control knob down to the “LOW” setting. The
burner will also warm up faster if a utensil is placed on the
grate.
Your Simmer Plate has a non-stick coating for easy cleaning. Take
care in using abrasives on the non-stick coating, as it will scratch.
Some wearing may occur on top of the Simmer Plate offset
fingers, this is normal with use.
5. The flame should be steady and blue in color. Foreign material
in the gas line, especially in new construction, may cause an
NOTE:
Simmer
Plate
Non-stick coatings
orange flame during initial operation. This will disappear with
further use.
if used at high
temperatures can be
harmful to birds. Avoid
keeping pets (birds)
in your kitchen during
cooking.
Grate
Stabilizer Feet
6. The flame should burn evenly around the perimeter of the
burner, except underneath each grate support finger where
the flame height is reduced by the Smart-Flame feature. If the
flame is uneven, ensure that the brass burner ring and porcelain
burner cap are properly positioned, then check for any foreign
material in the burner ring or on the burner cap. Remove any
foreign material with a straightened paper clip, wire, or needle.
Do not use a toothpick to remove clogs, as it could break off.
Do not damage the brass or distort the shape of the burner ring
ports.
Simmer Plate
7. Never light the burners with a match or other open flame. If a
burner does not ignite, refer to the Troubleshooting Guide.
enerGy saVInG tIps
•
Always use utensils with flat, smooth bottoms and tight-fitting
lids to retain heat and moisture.
settInG the bUrner flaMe
Setting the proper burner flame height for the desired cooking
process and selected utensil will result in superior cooking
performance, while also saving time and energy. Follow these
•
•
Minimize the amount of liquid or fat to reduce cooking times.
Select cookware of the proper size, material and construction
for the cooking process being performed.
Adjust the flame height to fit the utensil size.
After liquid reaches a boil, reduce the heat to maintain a
simmer rather than a rolling boil.
Use a timer rather than repeatedly removing the lid to check
food.
Thaw foods prior to cooking to reduce cooking time.
•
•
recommendations for best results:
1. Use low or medium flame heights when cooking in utensils that
are poor conductors of heat, such as glass, ceramic, and cast
iron cooking vessels. Reduce the flame height until it covers
approximately 1/3 of the utensil diameter. This will ensure even heating
within the utensil and reduce the likelihood of burning or scorching of
food.
•
•
ꢀ. Reduce the flame if it is extending beyond the bottom of the utensil. A
flame that licks along the sides of the utensil is potentially dangerous,
heats the utensil handle and kitchen instead of the food, and wastes
energy.
3. Reduce the flame height to the minimum level necessary to
perform the desired cooking process. Remember that food cooks
just as quickly at a gentle boil as it does at a vigorous, rolling boil.
Maintaining a higher boil than is necessary wastes energy, cooks
away moisture, and causes a loss in food flavor and nutrient level.
aCCessorIes (order separately)
•
•
Wok Ring (AWR) - the wok ring is a safe, convenient way to
stir fry. Just place it on top of the grate, aligning the wok ring
feet with the grate fingers. It will hold most standard sized
wok.
Griddle (AG11 or AG13) - The AG11 and AG13 easy clean
griddles are coated with a non-stick finish. Wonderful for
pancakes, eggs and various other foods. It is designed
to sit on top of your cooktop burner grates. A maximum
setting of medium is recommended to avoid damage to the
cooktop. See instructions included in griddle carton for further
information.
UsInG the sIMMer plate
The Simmer Plate has been specifically designed for simmering
and holding food at the lowest safe temperature. The Simmer
Plate is to be used by setting the burner to its lowest
setting. The Simmer Plate has been specifically designed for
simmering only. The Simmer Plate must be removed when
cooking.
WARNING
To avoid electrical shock or burns, turn off all controls and ensure
the cooktop is cool before cleaning.
To install your Simmer Plate locate the five feet on the bottom,
align with the five longest fingers on the cooktop grate then set
the plate on top of the grate. When correctly installed, the Simmer
Plate will rest about 1/ꢀ inch above the top surface of the grate
and will be locked in place to prevent turning.
IMPORTANT:
Do not use harsh or abrasive cleaning agents, waxes, polishes, or
commercial cooktop cleaners to clean the cooktop.
Read and follow the CARE AND CLEANING INSTRUCTIONS
to ensure that proper cooktop operation and appearance will
be maintained throughout the lifetime of the product. Several
materials and finishes are used in the cooktop. Each material
and finish must be properly cleaned according to the following
recommendations. Failure to follow these recommendations may
result in permanent damage to the cooktop.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and CleanInG
CleanInG tIps
Daily cleaning of the grates and burner caps is best accomplished
with a soft cloth or sponge dampened in a solution of warm water
and hand dishwashing liquid. Grates and burner caps should not
be cleaned in the dishwasher.
WARNING
1. Before cleaning the cooktop, ensure that all burners are turned
off and that all components are cool enough to safely touch.
2. After cleaning, reassemble all components before attempting to
operate the cooktop.
Stubborn stains may be removed by applying full-strength sprays
such as Simple Green, Ajax All-Purpose Cleaner, Formula 409,
or Scotch Guard. Metal polishing compounds such as Luneta or
Flitz may also be used. (If you are unable to locate these cleaning
compounds, please phone the DACOR Customer Service
Department for a referral.)
Mildly abrasive cleaners or applicators, such as S.O.S. Pads,
soap-filled steel wool pads, Soft Scrub, or Bon-Ami may be used
with extreme care on occasion to remove the most serious stains.
Exercise caution – extensive use of abrasives will eventually
damage the porcelain enamel surface.
Proper cleaning is necessary to maintain cooktop performance
and appearance, while also ensuring safe operation. The cleaning
effort necessary to maintain the cooktop varies according to the
type and amount of cooking. For example, more frequent cleaning
is required if the cooktop is used often for frying or other high
temperature operations.
Clean the cooktop thoroughly prior to operating it the first time.
For initial and everyday cleaning, use a soft cloth or sponge lightly
dampened with a solution of warm water and hand dishwashing
liquid to clean all components.
staInless steel sUrfaCes
Clean these surfaces with the provided Elco Stainless Steel
Cleaner. Rinse and dry with a soft lint-free cloth.
IMPORTANT:
1. To keep the cooktop looking its best, clean it after every use as
soon as all components are cool enough to safely touch. Also,
quickly wipe up spills that occur while cooking, being careful
not to touch any hot areas. Spills that remain on hot burner
components will be very difficult to clean, especially if allowed
to burn on. Spills of certain foods, such as tomatoes, citrus
juices, vinegar, alcohol, and milk, are very harmful if allowed
to stand for any length of time. Therefore, save time while also
maintaining a new appearance by cleaning regularly and shortly
after spills occur.
2. Use the mildest cleaner or procedure available to perform the
cleaning operation.
3. Use only a sponge, soft cloth, fibrous or plastic brush, and
nylon pad for cleaning. Avoid the use of abrasive cleaners such
as steel wool.
4. Always dry components completely before using the cooktop.
5. The use of brand names is intended only to indicate a type of
cleaning agent or cleaning implement. All products listed by
name must be used in accordance with the manufacturer’s
recommendations. Use of a brand name does not constitute an
endorsement, nor does omission of a particular brand imply that
a product is inferior.
IMPORTANT:
If commercially available stainless steel cleaners are used, it is
important to read the labels for chlorine compounds. Chlorine
is a corrosive substance. If these compounds are present, rinse
thoroughly and dry with a soft lint-free cloth.
Always wipe stainless steel surfaces with the grain.
porCelaIn sUrfaCes
The black and white models are finished in porcelain enamel.
Clean this surface with a solution of mild detergent and hot water.
Rinse with a soft cloth. Do not use abrasives or commercial oven
cleaners.
Stubborn stains may be removed by applying full-strength sprays
such as Simple Green, Ajax All-Purpose Cleaner, Formula 409, or
Scotch Guard.
IMPORTANT:
Recommendations for cleaning specific cooktop components are
summarized below:
1. Never use the cooktop surface as a cutting board.
2. Do not use abrasive cleaners or applicators on the cooktop.
3. Do not try to remove heavy spills with a sharp object such as a
knife or metal spatula. Sharp objects may scratch the cooktop.
4. A small amount of baby oil may be applied to stainless steel
tops to restore the lustre.
IMPORTANT:
The grates, burner caps, and spill-over areas on the cooktop, unlike
other porcelain enamel appliances in your home, are exposed to
extremely high temperatures in a matter of seconds. In addition to
this extreme thermal shock, the grates are subjected to mechanical
shock when utensils are placed on or slid across them. Finally,
spillovers introduce foods with high acidity to all of the porcelain
components. Due to these severe operating conditions, all porcelain
enamel components on the cooktop will undergo an inevitable
change in appearance with use. Meticulous care and cleaning will
slow but not eliminate this natural and expected aging process.
knobs and knob bezels
The control knobs provided with this cooktop are designed for
ease of use and longevity. The “D” shaped design of the knob
shaft ensures proper orientation when re-installing the knob.
IMPORTANT:
Never block the holes in the control panel beneath the knobs,
because this will impair the flow of combustion air and adversely
affect burner operation, possibly creating a hazardous condition.
Treating the porcelain components with care will slow the natural
deterioration that takes place with cooktop use. Please follow
these guidelines to keep the porcelain parts looking their best:
The knobs are made of a composite plastic. These components
should be washed regularly in warm, soapy water. Hand
dishwashing liquid is excellent for this task. Knobs should be
removed by gently pulling them straight out and off of the valve
shafts. The spill protectors should be cleaned in place. Use
caution to avoid introduction of moisture into the control panel
behind the bezels. To replace knobs, align the “D-shaped”
opening at the bottom of the knob with the “D-shaped” valve shaft,
then carefully press the knob onto the valve.
1. Do not use utensils having rough bottoms, as this can result in
permanent damage to the top surfaces of the porcelainized grates.
ꢀ. Do not drop utensils onto the grates or drag heavy pots across the
tops of the grates.
3. Set the grates into the locating dimples gently. Do not drop the grates
into place.
4. Use caution when cooking to avoid spills as much as possible.
Porcelain is acid-resistant but not acid-proof, so some foods can
cause permanent damage if allowed to remain on porcelain surfaces.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and CleanInG
IMPORTANT:
bUrner IGnItors
1. Turn the knobs to the “OFF” position prior to removing them
from the valve stems.
2. The cooktop should never be operated without the knobs in
place.
3. Do not soak the knobs in water or place them in the dishwasher.
4. Do not expose the knobs to direct flame, hot utensils, or other
sources of heat.
5. Do not use abrasive or corrosive cleaners or applicators, as
these could cause permanent damage.
Under certain cooking or cleaning conditions, your cooktop
ignitors may become coated with or corroded by food deposits,
splattered grease or cleaning agents. This condition can cause
erratic or continuous sparking. Keeping the ignitors clean and dry
will help to reduce this problem. To avoid unnecessary and costly
service calls, the homeowner should perform periodic cleaning of
the ignitors. An Ignitor Cleaning Brush is enclosed for your use in
cleaning the cooktop ignitors.
To clean the ignitors:
1. Be sure burners are cool to the touch. Remove the grate,
burner cap and burner rings.
ꢀ. Brush completely around the ignitor, including over and under
the edge of the metal cap and base. Use care while cleaning
here. The ignitor is porcelain and can be fragile.
3. DO NOT USE WATER when cleaning the ignitors. If a liquid
must be used to clean the ignitor effectively, use only a small
amount of rubbing alcohol.
bUrner bases
The burner base, which is permanently attached to the cooktop,
is made of aluminum. The base should be wiped clean using a
soft cloth or sponge that has been lightly dampened with warm
water and hand dishwashing liquid. Thoroughly clean and dry
the ignitors to prevent constant sparking of the reignition system.
Refer to the Burner Ignitors for cleaning tips.
4. After cleaning, reinstall the burner ring, burner cap and grate.
Make sure the brass burner ring is properly seated into the
burner base.
5. Test the burners. If erratic clicking is still present, make sure
the ignitor is completely dry. If the unit still exhibits problems
after drying, call your local DACOR Authorized Servicer.
bUrner rInGs
The brass burner rings spread the flame evenly around the burner
perimeters. The burner rings must seat properly in the burner
bases to enable proper cooktop operation. To ensure proper
seating, positioning tabs have been placed on the bottom of each
burner ring to slide into corresponding notches in the fixed burner
base.
U-bUrner Gas GrIllM(sGM464GG)
1. Your gas grill will develop greasy areas as a normal result of
use. Clean all greasy surfaces with mild soap and a cloth, this
includes heat control channel.
ꢀ. Do not wash the U-shaped burner in a dishwasher.
3. Clean the surface of the U-shaped burner with soapy water
and a brush. Do not submerge the burner in water. Rinse
under water and dry thoroughly.
4. During cleaning some material may get clogged in the holes
of the gas tubing. Use a paper clip or needle to free all
plugged hole of lose material. Dump all cleaning materials out
from inside the U-burner before reassembling the appliance.
To remove the burner ring, first remove the grate, then lift off the
porcelain burner cap. The burner ring may then be removed from
the burner base. Soak the burner ring in a warm solution of hand
dishwashing liquid and water, then rinse well with clean water. Dry
the burner thoroughly before placing it back on the burner base.
Stubborn stains may be removed by applying a metal polishing
compound such as Luneta or Flitz. (If you are unable to locate this
type of polishing compound, please phone the DACOR Customer
Service Department for a referral.)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
before yoU Call for serVICe
troUbleshootInG
Unnecessary service calls may be expensive, frustrating and time consuming. Before you call for service, please review the potential
problems, possible causes and remedies shown in the table below.
Problem
Possible Cause
Remedy
1. Nothing works
Cooktop is not connected to electrical power.
Have cooktop connected to a properly sized
electrical power supply by a qualified electrician.
Have an electrician check power supply,
including the house circuit breaker, wiring and
fuses.
ꢀ. Ignitors do not spark.
Power supply is not energized.
Circuit breaker is tripped.
House fuse is blown.
Reset circuit breaker.
Replace house fuse.
Power outage in local area.
Gas shut-off valve is on “off” position.
Gas supply is interrupted.
Contact power company.
Turn shut-off valve to “on” position.
Contact gas company.
3. Sparking, but no flame ignition,
4. Burners ignite, but flame is extremely large,
distorted or yellow.
Burner ring ports are clogged.
Clean burner ring ports with straightened paper
clip, needle or wire.
Burner ports or burner caps are not positioned
properly.
Remove and carefully re-install burner rings and
caps.
Cookop is being operated on the wrong type of
gas.
Ensure that the type of cooktop matches the gas
supply (natural gas of L.P. gas).
Regulator is not installed, is faulty, or is set for
the wrong type of gas.
Check installation, replace regulator, or set
regulator for proper gas type.
Contact gas company.
Remove obstruction.
5. Burner flame goes out at low setting.
Low gas supply pressure.
Air intake holes around knobs are obstructed.
Power supply is not grounded.
Power supply polarity is reversed.
Ignitors are wet or dirty.
Have power supply properly grounded
Have polarity corrected.
6. Ignitors spark continuously after flame
ignition.
Dry or clean ignitors.
Troubleshooting Guide
prodUCt MaIntenanCe
No maintenance, other than the CARE AND CLEANING
INSTRUCTIONS identified in this Use & Care Manual, should be
attempted by the owner/operator. All other maintenance and service
must be performed by a qualified appliance technician.
telephone number of the nearest service company.
DACOR works diligently to ensure your satisfaction when service
is necessary. However, if you are not completely satisfied with the
service provided, contact the company that performed the service
and express why you are not pleased. Normally, they will be willing
and able to resolve the problem.
If yoU need serVICe
First, review the recommended checks listed in the preceding
Troubleshooting Guide. Then, be certain that the appliance has
been installed properly and is being operated correctly. Familiarize
yourself with the warranty terms and conditions listed in the
PRODUCT WARRANTY section.
If the service agency is not able to respond effectively, call or
write the DACOR Customer Service Department. The phone
number and address of this department are listed on the inside
front cover of this manual. Please include your telephone number
if you choose to write. We will then do our utmost to assure your
happiness and satisfaction.
If the above checks have been completed and the problem has
not yet been remedied, call your local authorized DACOR service
representative. Your dealer can normally provide the name and
8
Download from Www.Somanuals.com. All Manuals Search And Download.
prodUCt warranty
what Is CoVered
what Is not CoVered
•
Service calls to educate the customer in the proper use and care of
the product.
CERTIFICATE OF WARRANTIES
DACOR COOKTOPS
•
•
•
•
Failure of the product when used for commercial, business, rental
or any application other than for residential consumer use.
Replacement of house fuses or fuse boxes, or resetting of circuit
breakers.
Damage to the product caused by accident, fire, flood or other acts
of God.
Breakage, discoloration or damage to glass, metal surfaces,
plastic components, trim, paint, or other cosmetic finish, caused by
improper usage or care, abuse, or neglect.
WIThIN ThE FIFTY STATES OF ThE U.S.A., ThE DISTRICT OF
COLUMBIA AND CANADA*:
FULL ONE-YEAR WARRANTY
If your DACOR product fails to function within one year of
the original date of purchase, due to a defect in material or
workmanship, DACOR will remedy the defect without charge
to you or subsequent users. The owner must provide proof of
purchase, upon request, and have the appliance accessible for
service.
THE REMEDIES PROVIDED FOR IN THE ABOVE EXPRESS
WARRANTIES ARE THE SOLE AND EXCLUSIVE REMEDIES.
THEREFORE, NO OTHER EXPRESS WARRANTIES ARE
MADE, AND OUTSIDE THE FIFTY STATES OF THE UNITED
STATES, THE DISTRICT OF COLUMBIA AND CANADA, ALL
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED
TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR USE OR PURPOSE, ARE
LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF
ORIGINAL PURCHASE. IN NO EVENT SHALL DACOR BE
LIABLE FOR INCIDENTAL EXPENSE OR CONSEQUENTIAL
DAMAGES. NO WARRANTIES, EXPRESS OR IMPLIED, ARE
MADE TO ANY BUYER FOR RESALE.
* Warranty is null and void if non-CSA approved product is
transported from the U.S.
OUTSIDE ThE FIFTY STATES OF ThE U.S.A., ThE DISTRICT
OF COLUMBIA AND CANADA:
LIMITED FIRST YEAR WARRANTY
If your DACOR product fails to function within one year of
the original date of purchase, due to a defect in material or
workmanship, DACOR will furnish a new part, F.O.B. factory,
to replace the defective part. All delivery, installation and labor
costs are the responsibility of the purchaser. The owner must
provide proof of purchase, upon request, and have the appliance
accessible for service.
Some states do not allow limitations on how long an implied
warranty lasts, or do not allow the exclusion or limitation of
inconsequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights that vary from state
to state.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
10
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
11
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
fold here
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL
POSTAGE WILL BE PAID BY ADDRESSEE
FIRST-CLASS MAIL
PERMIT NO. 4507
DIAMOND BAR CA
DACOR®, INC.
ATTN: WARRANTY PROCESSING DEPT
1440 BRIDGE GATE DR STE 200
PO BOX 6532
DIAMOND BAR CA 91765-9861
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
IMPORTANT:
Your warranty for this product CANNOT BE ACTIVATED until this form has been returned to Dacor. If you have
purchased more than one Dacor product, please return all forms in one envelope.
Please rest assured that under no conditions will Dacor sell your name or any of the information on this form for mailing list purposes. We
are very grateful that you have chosen Dacor products for your home and do not consider the sale of such information to be a proper way
of expressing our gratitude!
Owner’s Name:
Last (Please Print or Type)
First
Middle
Street:
City:
State:
Telephone:
Zip:
Zip:
Purchase Date:
Dealer:
City:
Email:
State:
Your willingness to take a few seconds to fill in the section below will be sincerely appreciated. Thank you.
1. How were you first exposed to Dacor products? (Please check one only.)
A. T.V. Cooking Show
B. Magazine
C. Appliance Dealer Showroom
D. Kitchen Dealer Showroom
E. Home Show
F
Builder
G. Architect/Designer
H. Another Dacor Owner
I. Model Home
J. Other
2. Where did you buy your Dacor appliances?
A. Appliance Dealer
B. Kitchen Dealer
C. Builder Supplier
D. Builder
E. Other
3. For what purpose was the product purchased?
A. Replacement only
B. Part of a Remodel
C. New Home
D. Other
4. What is your household income?
A. Under $75,000
B. $75,000 – $100,000
C. $100,000 – $150,000
D. $150,000 – $200,000
E. $200,000 – $250,000
F. Over $250,000
5. What other brands of appliances do you have in your kitchen?
A. Cooktop
B. Oven
C. Dishwasher
D. Refrigerator
6. Would you buy or recommend another Dacor product?
Yes
No
Comments:
Thank you very much for your assistance. The information you have
provided will be extremely valuable in helping us plan for the future
and giving you the support you deserve.
Place Serial Number Label Here
Web Site:
Corporate Phone:
(800) 793-0093
Download from Www.Somanuals.com. All Manuals Search And Download.
|