FEATURES
ꢀ
High Efficiency: 84% @ 1.5V/60A
ꢀ
Size: 57.9 x 61.0 x 12.7mm
(2.28” x 2.40” x 0.50”)
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Standard footprint
Industry standard pin out
Fixed frequency operation
Metal baseplate
Input UVLO, Output OCP, OVP, OTP
Basic insulation
No minimum load required
2:1 Input voltage range
ISO 9001, TL 9000, ISO 14001, QS9000,
OHSAS18001 certified manufacturing
facility
ꢀ
ꢀ
UL/cUL 60950 (US & Canada)
Recognized, and TUV (EN60950)
Certified
CE mark meets 73/23/EEC and
93/68/EEC directives
Delphi Series H48SL, 200W Half Brick Family
DC/DC Power Modules: 48V in, 1.5V/60A out
The Delphi Series H48SL Half Brick, 48V input, single output, isolated
DC/DC converters are the latest offering from a world leader in power
systems technology and manufacturing ― Delta Electronics, Inc. This
product family provides up to 200 watts of power (3.3V and above) or
60A of output current in an industry standard footprint. With creative
design technology and optimization of component placement, these
converters possess outstanding electrical and thermal performance, as
well as extremely high reliability under highly stressful operating
conditions. All models are fully protected from abnormal input/output
voltage, current, and temperature conditions. The Delphi Series
converters meet all safety requirements with basic insulation.
OPTIONS
ꢀ
ꢀ
ꢀ
Positive Remote On/Off logic
Negative trim
Short pin lengths
APPLICATIONS
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Telecom/Datacom
Wireless Networks
Optical Network Equipment
Server and Data Storage
Industrial/Test Equipment
DATASHEET
DS_H48SL1R560_10302006
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CHARACTERISTICS CURVES
90
20.0
16.0
12.0
8.0
36Vin
48Vin
75Vin
85
80
75
70
4.0
36Vin
48Vin
40
75Vin
0.0
65
10
20
30
40
50
60
10
20
30
50
60
OUTPUT CURRENT(A)
OUTPUT CURRENT (A)
Figure 1: Efficiency vs. load current for minimum, nominal, and
Figure 2: Power dissipation vs. load current for minimum,
maximum input voltage at 25°C.
nominal, and maximum input voltage at 25°C.
3.5
Io=60A
Io=36A
Io=6A
3.0
2.5
2.0
1.5
1.0
0.5
0.0
30
35
40
45
50
55
60
65
70
75
INPUT VOLTAGE (V)
Figure 3: Typical input characteristics at room temperature
DS_H48SL1R560_10302006
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CHARACTERISTICS CURVES
For Negative Remote On/Off Logic
Figure 4: Turn-on transient at full rated load current (resistive
load) (2 ms/div). Top Trace: Vout; 500mV/div; Bottom Trace:
ON/OFF input: 10V/div
Figure 5: Turn-on transient at zero load current (2 ms/div). Top
Trace: Vout: 500mV/div; Bottom Trace: ON/OFF input: 10V/div
For Positive Remote On/Off Logic
Figure 6: Turn-on transient at full rated load current (resistive
load) (2 ms/div). Top Trace: Vout; 500mV/div; Bottom Trace:
ON/OFF input: 2V/div
Figure 7: Turn-on transient at zero load current (2 ms/div). Top
Trace: Vout: 500mV/div; Bottom Trace: ON/OFF input: 2V/div
DS_H48SL1R560_10302006
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CHARACTERISTICS CURVES
Figure 8: Output voltage response to step-change in load
current (75%-50%-75% of Io, max; di/dt = 0.1A/µs). Load cap:
10µF, tantalum capacitor and 1µF ceramic capacitor. Top Trace:
Vout (100mV/div), Bottom Trace: Iout (10A/div). Scope
measurement should be made using a BNC cable (length
shorter than 20 inches). Position the load between 51 mm to
76 mm (2 inches to 3 inches) from the module.
Figure 9: Output voltage response to step-change in load
current (75%-50%-75% of Io, max; di/dt = 2.5A/µs). Load cap:
470µF, 35mΩ ESR solid electrolytic capacitor and 1µF ceramic
capacitor. Top Trace: Vout (100mV/div), Bottom Trace: Iout
(10A/div). Scope measurement should be made using a BNC
cable (length shorter than 20 inches). Position the load
between 51 mm to 76 mm (2 inches to 3 inches) from the
module.
Figure 10: Test set-up diagram showing measurement points
for Input Terminal Ripple Current and Input Reflected Ripple
Current.
Note: Measured input reflected-ripple current with a simulated
source Inductance (LTEST) of 12 µH. Capacitor Cs offset
possible battery impedance. Measure current as shown above.
DS_H48SL1R560_10302006
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CHARACTERISTICS CURVES
Figure 11: Input Terminal Ripple Current, ic, at full rated output
current and nominal input voltage with 12µH source impedance
and 33µF electrolytic capacitor (1A/div).
Figure 12: Input reflected ripple current, is, through a 12µH
source inductor at nominal input voltage and rated load current
(20 mA/div).
Copper Strip
Vo(+)
SCOPE
RESISTIVE
LOAD
10u
1u
Vo(-)
Figure 13: Output voltage noise and ripple measurement test
setup
DS_H48SL1R560_10302006
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CHARACTERISTICS CURVES
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
48Vin
0
10
20
30
40
50
60
70
80
90
100
LOAD CURRENT (A)
Figure 14: Output voltage ripple at nominal input voltage and
rated load current (20 mV/div). Load capacitance: 1µF ceramic
capacitor and 10µF tantalum capacitor. Bandwidth: 20 MHz.
Scope measurement should be made using a BNC cable
(length shorter than 20 inches). Position the load between 51
mm to 76 mm (2 inches to 3 inches) from the module.
Figure 15: Output voltage vs. load current showing typical
current limit curves and converter shutdown points.
DS_H48SL1R560_10302006
7
Download from Www.Somanuals.com. All Manuals Search And Download.
THERMAL CURVES: NO HEATSINK, EITHER ORIENTATION
26 mm
( 1. 02")
H48SL1R560(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A)
@ Vin < 60V (Either Orientation, no Heat sink)
64
56
48
40
32
24
16
8
600LFM
500LFM
out
400LFM
Natural
Convection
Sense
On/Off
Case
Trim
100LFM
Sense(-)
out
200LFM
300LFM
0
0
10
20
30
40
50
60
70
80
90
100
Ambient Temperature (℃)
Figure 16: Case temperature measurement location.
Figure 17: Output current vs. ambient temperature and air
Pin locations are for reference only.
velocity (Vin<60V)
H48SL1R560(Standard) Output Current vs. Ambient Temperature and Air Velocity
H48SL1R560(Standard) Power Dissipation vs. Ambient Temperature and Air Velocity
@ Vin = 75V (Either Orientation, no Heat sink)
(Either Orientation, no Heat sink)
Power Dissipation (Watts)
Output Current(A)
21
18
15
12
9
64
600LFM
600LFM
56
500LFM
48
500LFM
40
32
24
16
8
Natural
Convection
400LFM
400LFM
Natural
Convection
100LFM
100LFM
200LFM
6
200LFM
300LFM
300LFM
3
0
0
0
10
20
30
40
50
60
70
80
90
100
0
10
20
30
40
50
60
70
80
90
100
Ambient Temperature (℃)
Ambient Temperature (℃)
Figure 18: Output current vs. ambient temperature and air velocity
Figure 19: Power dissipation vs. ambient temperature and air
(Vin=75V)
velocity
DS_H48SL1R560_10302006
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DESIGN CONSIDERATIONS
Input Source Impedance
ꢀ
ꢀ
ꢀ
The input source must be insulated from the ac
mains by reinforced or double insulation.
The impedance of the input source connecting to the
DC/DC power modules will interact with the modules
and affect the stability. A low ac-impedance input source
is recommended. If the source inductance is more than
a few µH, we advise adding a 10 to 100 µF electrolytic
capacitor (ESR < 0.7 Ω at 100 kHz) mounted close to
the input of the module to improve the stability.
The input terminals of the module are not operator
accessible.
If the metal baseplate is grounded, one Vi pin and
one Vo pin shall also be grounded.
Layout and EMC Considerations
ꢀ
A SELV reliability test is conducted on the system
where the module is used, in combination with the
module, to ensure that under a single fault,
hazardous voltage does not appear at the module’s
output.
Delta’s DC/DC power modules are designed to operate
in a wide variety of systems and applications. For design
assistance with EMC compliance and related PWB
layout issues, please contact Delta’s technical support
team. An external input filter module is available for
easier EMC compliance design. Application notes to
assist designers in addressing these issues are pending
release.
When installed into a Class II equipment (without
grounding), spacing consideration should be given to
the end-use installation, as the spacing between the
module and mounting surface have not been evaluated.
Safety Considerations
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
The power module must be installed in compliance with
the spacing and separation requirements of the
end-user’s safety agency standard, i.e., UL60950,
CAN/CSA-C22.2 No. 60950-00 and EN60950:2000 and
IEC60950-1999, if the system in which the power
module is to be used must meet safety agency
requirements.
This power module is not internally fused. To achieve
optimum safety and system protection, an input line fuse
is highly recommended. The safety agencies require a
normal-blow fuse with 20A maximum rating to be
installed in the ungrounded lead. A lower rated fuse can
be used based on the maximum inrush transient energy
and maximum input current.
Basic insulation based on 75 Vdc input is provided
between the input and output of the module for the
purpose of applying insulation requirements when the
input to this DC-to-DC converter is identified as TNV-2
or SELV. An additional evaluation is needed if the
source is other than TNV-2 or SELV.
Soldering and Cleaning Considerations
Post solder cleaning is usually the final board assembly
process before the board or system undergoes electrical
testing. Inadequate cleaning and/or drying may lower the
reliability of a power module and severely affect the
finished circuit board assembly test. Adequate cleaning
and/or drying is especially important for un-encapsulated
and/or open frame type power modules. For assistance
on appropriate soldering and cleaning procedures,
please contact Delta’s technical support team.
When the input source is 60 Vdc or below, the power
module meets SELV (safety extra-low voltage)
requirements. If the input source is a hazardous voltage
which is greater than 60 Vdc and less than or equal to 75
Vdc, for the module’s output to meet SELV requirements,
all of the following must be met:
DS_H48SL1R560_10302006
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES DESCRIPTIONS
Vi(+)
Vo(+)
Over-Current Protection
Sense(+)
The modules include an internal output over-current
protection circuit, which will endure current limiting for
an unlimited duration during output overload. If the
output current exceeds the OCP set point, the modules
will automatically shut down (hiccup mode).
ON/OFF
Sense(-)
Vi(-)
Vo(-)
The modules will try to restart after shutdown. If the
overload condition still exists, the module will shut down
again. This restart trial will continue until the overload
condition is corrected.
Figure 20: Remote on/off implementation
Remote Sense
Over-Voltage Protection
Remote sense compensates for voltage drops on the
output by sensing the actual output voltage at the point
of load. The voltage between the remote sense pins
and the output terminals must not exceed the output
voltage sense range given here:
The modules include an internal output over-voltage
protection circuit, which monitors the voltage on the
output terminals. If this voltage exceeds the over-voltage
set point, the module will shut down and latch off. The
over-voltage latch is reset by either cycling the input
power or by toggling the on/off signal for one second.
[Vo(+) – Vo(–)] – [SENSE(+) – SENSE(–)] ≤ 10% × Vout
This limit includes any increase in voltage due to
remote sense compensation and output voltage set
point adjustment (trim).
Over-Temperature Protection
The over-temperature protection consists of circuitry
that provides protection from thermal damage. If the
temperature exceeds the over-temperature threshold
the module will shut down.
Vi(+) Vo(+)
Sense(+)
The module will try to restart after shutdown. If the
over-temperature condition still exists during restart, the
module will shut down again. This restart trial will
continue until the temperature is within specification.
Sense(-)
Vi(-) Vo(-)
Contact
Resistance
Contact and Distribution
Losses
Remote On/Off
Figure 21: Effective circuit configuration for remote sense
operation
The remote on/off feature on the module can be either
negative or positive logic. Negative logic turns the
module on during a logic low and off during a logic high.
Positive logic turns the modules on during a logic high
and off during a logic low.
If the remote sense feature is not used to regulate the
output at the point of load, please connect SENSE(+) to
Vo(+) and SENSE(–) to Vo(–) at the module.
Remote on/off can be controlled by an external switch
between the on/off terminal and the Vi(-) terminal. The
switch may be an open collector or open drain.
The output voltage may be increased by both the
remote sense and the trim; however, the maximum
increase is the larger of either the remote sense or the
trim, not the sum of both.
For negative logic if the remote on/off feature is not
used, please short the on/off pin to Vi(-). For positive
logic if the remote on/off feature is not used, please
leave the on/off pin floating.
When using remote sense and trim, the output voltage
of the module is usually increased, which increases the
power output of the module with the same output
current.
Care should be taken to ensure that the maximum
output power does not exceed the maximum rated
power.
DS_H48SL1R560_10302006
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES DESCRIPTIONS (CON.)
Output Voltage Adjustment (TRIM)
To increase or decrease the output voltage set point,
connect an external resistor between the TRIM pin and
either the SENSE(+) or SENSE(-). The TRIM pin
should be left open if this feature is not used.
Figure 23: Circuit configuration for trim-up (increase output
voltage)
If the external resistor is connected between the TRIM
and SENSE (+) the output voltage set point increases
(Fig. 23). The external resistor value required to obtain
a percentage output voltage change △% is defined
as:
Figure 22: Circuit configuration for trim-down (decrease
output voltage)
If the external resistor is connected between the TRIM
and SENSE (-) pins, the output voltage set point
decreases.(Fig. 22) The external resistor value
required to obtain a percentage of output voltage
change △% is defined as:
)
Vo⋅ 100 + ∆%
100 + 2∆%
∆%
⎡
⎣
⎤
⎦
Rtrim up=
−
ΚΩ
1.225⋅∆%
Ex. When Trim-up +10%(1.5V×1.1=1.65V)
100
⎛
⎝
⎞
⎠
Rtrim down=
Vo := 1.5V ∆ := 10
− 2 ΚΩ
∆%
(
)
Vo⋅ 100 + ∆
100 + 2⋅∆
Ex. When Trim-down -20%(1.5V×0.8=1.2V)
−
= 1.469 KΩ
1.225⋅∆
∆
Vo := 1.5 V
∆ := 20
100
The output voltage can be increased by both the remote
sense and the trim, however the maximum increase is
the larger of either the remote sense or the trim, not the
sum of both.
− 2 = 3 K Ω
∆
When using remote sense and trim, the output voltage
of the module is usually increased, which increases the
power output of the module with the same output
current.
Care should be taken to ensure that the maximum
output power of the module remains at or below the
maximum rated power.
DS_H48SL1R560_10302006
11
Download from Www.Somanuals.com. All Manuals Search And Download.
THERMAL CONSIDERATIONS
Thermal management is an important part of the system
design. To ensure proper, reliable operation, sufficient
cooling of the power module is needed over the entire
temperature range of the module. Convection cooling is
usually the dominant mode of heat transfer.
Thermal Derating
Heat may be removed by increasing airflow over the
module. The module’s maximum case temperature is
+100°C. To enhance system reliability, the power
module should always be operated below the maximum
operating temperature. If the temperature exceeds the
maximum module temperature, reliability of the unit may
be affected.
Hence, the choice of equipment to characterize the
thermal performance of the power module is a wind
tunnel.
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in
heated vertical wind tunnels that simulate the thermal
environments encountered in most electronics
equipment. This type of equipment commonly uses
vertically mounted circuit cards in cabinet racks in which
the power modules are mounted.
The following figure shows the wind tunnel
characterization setup. The power module is mounted
on a test PWB and is vertically positioned within the
wind tunnel. The space between the neighboring PWB
and the top of the power module is constantly kept at
6.35mm (0.25’’).
PWB
MODULE
FACING PWB
AIR VELOCITY
AND AMBIENT
TEMPERATURE
MEASURED BELOW
THE MODULE
50.8 (2.0”)
AIR FLOW
12.7 (0.5”)
Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)
Figure 24: Wind tunnel test setup
DS_H48SL1R560_10302006
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICAL DRAWING
Pin No.
Name
Function
1
2
3
4
5
6
7
8
9
-Vin
Case
Negative input voltage
Case ground
Remote ON/OFF
Positive input voltage
Positive output voltage
Positive remote sense
Output voltage trim
Negative remote sense
Negative output voltage
ON/OFF
+Vin
+Vout
+SENSE
TRIM
-SENSE
-Vout
Pin Specification:
Pins 1-4, 6-8
Pins 5 & 9
1.00mm (0.040”) diameter
2.00mm (0.079”) diameter
All pins are copper with Tin plating.
DS_H48SL1R560_10302006
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NUMBERING SYSTEM
H
48
S
L
1R5
60
N
R
F
A
Form Factor
Input Number of
Voltage Outputs
Product
Series
Output
Voltage Current
Output
ON/OFF
Logic
Pin Length
Option Code
H – Half-Brick
48V
S - Single
L - IMS,
positive trim
1R5 - 1.5V 60 - 60A
N - Negative
P - Positive
R - 0.170”
N - 0.145”
K - 0.110”
A - Standard
Functions
F- RoHS 6/6
Lead Free)
MODEL LIST
MODEL NAME
INPUT
OUTPUT
EFF @ 100% LOAD
H48SL1R560NRFA
H48SL1R860NRFA
H48SL2R560NRFA
H48SL3R360NRFA
H48SL05040NRFA
H48SL12020NRFA
36V~75V
36V~75V
36V~75V
36V~75V
36V~75V
36V~75V
3.6A
4.3A
5.7A
7.4A
7.4A
8.7A
1.5V
60A
60A
60A
60A
40A
20A
84%
1.8V
2.5V
3.3V
5V
85%
88%
89%
90.5%
91%
12V
Default remote on/off logic is negative and pin length is 0.170”
For different remote on/off logic and pin length, please refer to part numbering system above or contact your local sales office.
USA:
Telephone:
East Coast: (888) 335 8201
West Coast: (888) 335 8208
Fax: (978) 656 3964
Email: [email protected]
Europe:
Asia & the rest of world:
Telephone: +886 3 4526107 x6220
Fax: +886 3 4513485
Telephone: +41 31 998 53 11
Fax: +41 31 998 53 53
Email: [email protected]
Email: [email protected]
WARRANTY
Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon
request from Delta.
Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta for its
use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these specifications
at any time, without notice.
DS_H48SL1R560_10302006
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|