MR850EVO/MR650EVO
Rolling Garage Door Opener
Installation and Operating Instructions
Owners Copy: Please keep these instructions for future reference
This manual contains IMPORTANT SAFETY information
DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2 TOOLS REQUIRED
CARTON INVENTORY
1. Instruction manual (this document)
2. Stop collar
3. Clamp bracket
1. Ladder
2. Adjustable wrench for U-bolts already installed
on the door
4. Release handle, cord and risk of entrapment card
5. Transmitters (2)
3. 8 mm socket, 10 mm socket and 13 mm extended
socket and socket wrench
6. Wireless wall button
7. Hardware bag
4. 300 mm socket extension (for minimum side-room
installations)
8. Weight bar
9. Clamp plate
10. Warning label and risk of entrapment label
5. Drill and 5.5 mm drill bit
6. Philips-head screwdriver
7. Marker pen
8. Door stand or similar device to safely support door
(not shown)
11. Opener
13 mm, 10 mm, 8 mm
11
5.5 mm
3
DOOR REQUIREMENTS
The maximum allowable door height is 4.5 m with a maximum curtain area of 16.5 m²* (MR650EVO) -18 m²*
(MR850EVO) (door height in metres multiplied by the width in metres). The door must be spring balanced.
*The Protector System™ (IR Beams) must be installed if the force at the edge of the closing door exceeds
400 N (40 kgf). Door axle diameter must not exceed 35 mm.
Minimum distance from
edge of curtain to edge of
door bracket 45 mm
95 mm
Independent
clamping method
Direct clamping
method
95 mm
Ensure that there is at least 45 mm from the edge of the curtain to the edge of the bracket. If the roller door
drum is on the edge of the curtain or is a smaller diameter, additional clearance may be required.
If the drum is more than 60 mm from the curtain edge or of a smaller diameter, an extension pole kit
may be required.
Different drum and bracket types may result in the minimum side room clearance not being possible and
extension poles being required. Ensure there is a power point near the opener.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
4 TESTING THE DOOR
Complete the following test to ensure your door is well
balanced, and not sticking or binding:
• Disable all locks and remove any ropes connected to the
garage door.
• Lift the door to about halfway and then release it. The
door should remain spring balanced.
• Raise and lower the door to determine if there are any
sticking or binding points (20 kgf is the absolute maximum
allowable to raise or lower the door in any position).
• If your door does not hold in place or the door binds or
sticks, call a qualified door technician before installing the
opener.
5
INSTALLING THE STOP COLLAR
• Install the stop collar on the opposite end to where
the opener is to be installed.
Non opener side
Opener side
• Fit the stop collar hard against the boss of the door
drum. Ensure the U-bolt holding the door shaft to the door
bracket is tightly secured.
SAFETY CHECK!
Is the stop collar
installed?
YES: proceed to the next
step
NO: install the stop collar
before proceeding
INSTALLING THE WEIGHT BAR (PROVIDED)
6
• Place the weight in the centre of the door (as shown).
• Use a pencil to mark the two hole positions.
• If the door curtain does not have a handle you will need
to drill two 5.5 mm holes through the two marked
positions, then place the weight bar on the inside of the
door.
• Use the bolts, washers and nuts (provided) to
fasten the weight bar in place.
NOTE: If the door has a lifting handle, remove the
handle, nuts & bolts. Place weight bar over the
handle holes, insert extended bolts through the
weight bar & fasten handle back in place.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
THE RELEASE HANDLE & CORD
7
• Thread one end of the rope through the hole in the top
of the red release handle so that “NOTICE” reads
right side up as shown.
• Secure with an overhand knot at least 25 mm from the
end of the rope to prevent slipping.
• Thread the other end of the rope through the loop of
the manual release cable.
Learn Limits
button
UP Arrow
button
• Adjust rope length so the handle (when installed) will
be no higher than 1.8 m above the floor. Secure with
an overhand knot. If the door is greater than 2.5 m in
height the release cord extension kit accessory is
required.
DOWN Arrow
button
Learn
button
Release cable
Rope
NOTE: Final adjustment of handle height should be
completed after the opener is installed. If it is
necessary to cut the rope, heat seal the cut end to
prevent unravelling (refer section 16).
Manual release
warning label
Overhand knot
Release handle
8
OPERATING THE MANUAL RELEASE
To disengage the opener
Pull the release cord down firmly,
(opener will make a clicking noise).
To re-engage the opener
Pull the release cord down firmly,
(opener will make a clicking noise).
Pull down
FIRMLY
Disable all locks and remove any ropes connected to the garage door.
Take care when operating the manual release as an open door may fall rapidly due to weak or
broken springs, or being out of balance.
9
PINNING THE DOOR
Note: A ballooning door may delay the safety reversal
response and can compromise garage door security.
Free curtain
Ballooning Add fasteners here
• To remedy any ballooning place self tapping metal screws
or rivets where the curtain leaves the roll. Secure these
through the curtain into the drum wheel at each end of the
roll.
• After determining the correct fastener location as shown, lift
the door approximately half a turn from the closed position
to allow access for drilling.
Door closed
Door secure
Door can be
lifted
4
Download from Www.Somanuals.com. All Manuals Search And Download.
10
ATTACHING EXTENSION POLES (IF REQUIRED)
Optional accessory not provided
• Align the extension pole holes with the drive legs.
• Insert the extension poles into the drive leg and fix in
place using screws provided.
• Slide the reinforcing brace over the poles and fix in
place using the screws provided.
Release cable
Rope
Manual Release
Warning Label
Overhand knot
Reinforcing brace must be used. Use
extension pole kit part number 001B6449-1
Release handle
11
LEFT / RIGHT HAND INSTALLATION
LEFT
RIGHT
(factory
default
setting)
(handing must be
changed during limit
setting, section 13)
Inside garage looking out
5
Download from Www.Somanuals.com. All Manuals Search And Download.
12
INSTALLATION PROCEDURE
Do not allow people to walk under or
around the door during the installation
process as serious injury can occur.
NOTE: The opener can be installed on either side
of the door. The following instructions are for
RIGHT HAND INSTALLATIONS (as illustrated i.e.
inside the garage looking out). For left hand
installations, reverse the instruction terminology
(eg LEFT for RIGHT etc).
Rope
Door stand
Preparation:
• Place the opener in manual release mode (refer
section 8).
• Open the roller door fully. For safety, tie a rope
around the door.
• Ensure the door axle U-BOLT and door mounting
bracket on the left hand side (non opener side) are
securely fastened.
• Support the door with a door stand or similar device
to safely support the door.
• Mark the position of the door shaft on the right hand
door bracket (for reassembly purposes).
• While the door is supported, remove the right hand
axle U-Bolt and door mounting bracket from the wall.
Rope
Install the opener:
• Slide the opener over the door axle and engage the
drive legs into the door drum wheel, either side of a
spoke. Extensions may be necessary (refer section
10).
Door stand
• Refit the door mounting bracket to the wall. If the
door bracket needs to be relocated due to opener
width, refer section 3.
• Clamp the opener on the door axle and door bracket
in the marked position using the clamp assembly
supplied (tighten to 25 – 28 Nm).
• If side room exceeds 95mm clamp independently to
the door axle as illustrated in section 3.
• Remove all ropes and the support stand.
• Check the operation of the door in manual mode by
raising and lowering by hand. It should operate
smoothly without sticking or binding. The disengage
handle should already be attached less than 1.8m
above the floor (refer section 7).
Tighten to
25-28 Nm
Connect the power:
• Position the power cable away from the door curtain
and any moving parts.
• Plug the opener into a nearby power point and turn
ON.
• The opener courtesy LEDs should turn ON.
• The opener must now be programmed for:-
• DOOR TRAVEL LIMITS
(Section 13)
• RIGHT OR LEFT HAND OPERATION (Section 13)
)
(Section 14
• FORCE SETTING
6
Download from Www.Somanuals.com. All Manuals Search And Download.
13
SETTING THE LIMITS FOR RIGHT OR LEFT HAND OPERATION AND FORCE
Travel limits set how far your door goes up and down. Your opener must be configured correctly for right or left
hand installation to operate correctly, if not the door will rotate in the reverse direction.
NOTE: The MR850EVO/MR650EVO opener is factory configured for right hand installation.
The opener will operate during this procedure. Make sure the door is clear of obstruction.
Ensure your hands are away from any moving parts before activating the door.
Setting right or left hand operation:
Press and hold
until
• Ensure the door is positioned halfway and the opener
is engaged.
• Turn the power ON. After 2 seconds the Courtesy
LEDs will flash 5 times.
• Press and hold the black (Limit) button until the
orange indicator LED starts flashing, and then
release. Either right or left courtesy LEDs will light
up.
• For right hand installations, the right side bank of
LEDs must light up, and for left hand installations,
the left hand bank must light up.
• If the incorrect bank of LEDs is illuminated, simply
press the Yellow learn button until the opposite bank
lights up.
• Press and release the Black limit set button to
accept hand. UP button will flash.
FLASHING
LED
Right bank
will light up
(IF REQUIRED)
To change
press and hold
until correct
bank lights up
Left bank
will light up
for Left hand
installation
Setting the open (UP) limit:
• Press and hold the “UP” button, until the door
reaches the desired open position, and then release.
You can adjust the door by using the DOWN button
and UP button to adjust as necessary. Make sure
there is enough room for your vehicle to pass under.
Press & release to accept
selected hand.
Press and hold to drive
door up to open
• Press and release the Black limit set button to
acknowledge the Up position.
If required: Use DOWN button to adjust
• Courtesy light flashes twice and DOWN button will
flash.
Press & release to set the
UP limit
Setting the bottom (DOWN) limit:
• Press and hold the “DOWN” button until the door
reaches the desired closed position. If the door
closes too hard against the floor, use the UP and
DOWN button to adjust.
Press and hold to drive
door down to closed
If required: Use UP button to adjust
• Press and release the Black limit set button to
acknowledge the down position.
Press & release to set the
DOWN limit
• Courtesy light flashes twice and UP button will flash.
Setting the FORCE:
Activate door to open
Orange
• Press and release the UP button. The door will travel
to the UP limit and the DOWN button will flash.
• Press and release the DOWN button. The door will
travel to the DOWN limit.
LED ON &
Courtesy LEDS
• The indicator LED will stop flashing indicating the
force has been learned.
on Dim
NOTE: The courtesy LEDs will go out after 2.5
min.
Close the door to test limits
• The door must travel through a complete cycle, UP
and DOWN, in order for the force to be set properly.
If the opener cannot open and close your door fully,
inspect your door to ensure that it is balanced
properly and is not sticking or binding.
Motor will make a click &
FULL BRIGHT courtesy
LEDs will turn on
7
Download from Www.Somanuals.com. All Manuals Search And Download.
14
TESTING THE SAFETY REVERSE SYSTEM
The safety reverse system test is important.
The garage door must reverse on contact
with a 40 mm obstacle laid flat on the floor.
Failure to properly adjust the opener may result in
serious personal injury from a closing garage
door.
40 mm
Operate the door in the down direction. The door must
reverse upon contact with the obstacle. If the door
stops on the obstacle, remove obstacle and repeat
limit and force setting (refer section 13).
40 mm Test obstacle
Repeat test of the safety reverse system.
FIXING WARNING LABELS
15
Once you have completed your installation and
successfully carried out the safety reverse system
test (outlined above), install the warning labels
provided with your opener as shown.
The risk of entrapment label must be installed
adjacent to the release handle at a height of less than
1.8 m from the floor.
Handle should be
less than 1.8 m
The WARNING label must be installed in a prominent
place near any fixed control.
Any fixed wall control or wireless door control must be
mounted at a height of no less than 1.5 m out of the
reach of children.
Wall control, or
wireless push button
no less than 1.5 m
Ensure the manual release instruction card is
attached to the rope as detailed in section 7.
Read the safety instructions (page 1) for further
details concerning safety.
STANDARD INSTALLATION COMPLETE
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL THE PROTECTOR SYSTEM™ (IR BEAMS) OPTIONAL ACCESSORY
16
NOTE: This accessory must be used for all
installations where the closing force as measured
on the bottom of the door is over 400 N (40 kgf).
After the opener has been installed and adjusted, the
Protector System™ accessory can be installed.
Instructions are included with this accessory.
IR Beams must be installed
to detect a 100 mm high
obstacle at any point along
the floor.
The Protector System™ provides an additional
measure of safety against a small child or animal
being trapped under a garage door. It uses an infra-
red beam, which when broken by an obstruction,
causes a closing door to open and prevents an open
door from closing and is strongly recommended for
homeowners with young children.
Red LED
MUST BE ON
Red LED
MUST BE
O
NOTE: The opener will automatically detect the
Protector SystemTM when it is installed and
operating for 5 minutes (during this time the beams
must remain unobstructed). The opener will not
close unless the beams are aligned.
IR Beam
IR Beam
SAFETY FIRST!
Whilst Chamberlain have engineered safety features into your garage door opener, we urge you to consider fitting
IR Beams to your new garage door opener. In many countries these devices are compulsory to assist in
preventing serious injury or property damage. For your own peace of mind and the safety of others please install
this inexpensive safety device.
Timer to close feature (TTC)
Auto close is NOT recommended for households with young children.
The Timer-to-close feature allows the door to automatically close after a specified time period. Prior to the door
closing, the garage door opener lights flash for 8 seconds before the door begins to close.
If the door encounters an obstruction while closing, the opener will make a second attempt to close the door. If
an obstruction occurs on the second attempt, the garage door opener will open, stop and WILL NOT close until
the obstruction has been cleared and the opener has been operated again.
NOTE: The Protector SystemTM MUST be installed and operating for 5 minutes to enable this feature.
Installing and adjusting:
• Turn the opener off
• Install the Protector SystemTM using the brackets, wires and instructions provided with the product. Twist the
two white (only) wires together and terminate them into the white (2) terminal. Twist the two white/black wires
together and terminate them into the grey (3) terminal.
MR850EVO ONLY
• Turn the opener on
With the door at the down limit, press and hold DOWN
arrow until orange LED starts blinking.
Yellow LEARN button is used to cycle through the TTC settings:
1 x long blink = TTC OFF
1 x short blink = TTC 1 min
2 x short blink = TTC 5 min
3 x short blink = TTC 10 min
Up
Black
Learn
Button
Yellow
Learn
Button
Down
Press black rectangle button to set and exit.
Door may operate unexpectedly, therefore do not allow anything to stay in the path of the door.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING YOUR E128M WIRELESS WALL BUTTON
17
Disconnect power to the opener whilst installing
this accessory to prevent accidental activation.
Locate minimum 1.5 m above the floor
To install:
• Carefully pry open the E128M and locate the two screws for
mounting.
• Attach to the wall using the two screws and wall anchors
provided if mounting to a plaster wall. If using a recessed wall
box do not use anchors.
+
NOTE: Do not overtighten screws.
NOTE: The wall control supplied with your opener should be pre-programmed by the factory.
If adding a new wall control, program into the opener before mounting the unit as detailed in
section 18.
18
WIRELESS PROGRAMING (OPTIONAL ACCESSORIES)
NOTE: Transmitter(s) and wall button supplied with your opener are factory programmed.
Activate the opener only when the door is in full view, free of obstruction and properly adjusted.
No one should enter or leave garage whilst the door is in motion. Do not allow children to operate
push button(s) or transmitter(s). Do not allow children to play near the door.
Fix any wall control at a height of at least 1.5 m and within sight of the door but away from any
moving parts.
TO ADD Transmitters / Wireless wall button
NOTE: If adding an installed wall control (E128M)
you will need a second person to press and hold
or
the desired button. If not installed, program the
wall button into the opener before mounting.
Press and hold down the desired
Button.
ADDING transmitters using the LRN “LEARN”
button
• Press and hold down the button you wish to program
to the opener.
LED will FLASH
• The orange LED will flash to indicate it is receiving
signal from the transmitter.
Press LEARN
• Press and release the “LRN” button.
• The courtesy LEDs will flash once.
• Ensure the door is clear of obstruction, then test the
transmitter.
Release LRN button when
Courtesy LEDs
flashes once
Deleting ALL transmitter codes
NOTE: This deletes all transmitters and codes
TO DELETE ALL REMOTES
• Press and hold the LRN learn button until the orange
indicator light goes out (approximately 9
sec).
Press LEARN for 9 seconds
LED on WILL TURN ON
After 9 seconds all remotes
are deleted and LED will go
out.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
KEYLESS DEVICE PROGRAMMING (OPTIONAL ACCESSORIES )
19
Activate the opener only when the door is in
Locate
the yellow
learn button
1
2
3
full view, free of obstruction and properly
adjusted. No one should enter or leave
garage whilst the door is in motion. Do not
allow children to operate push button(s) or
transmitter(s). Do not allow children to play
near the door.
Press and release
the yellow
learn button
Wireless Keypad E840M
3
To set the keyless entry PIN:
1.Locate the Yellow Learn button on the garage door
opener.
Enter a 4-digit
PIN of your
choice
2.Press and release the Yellow Learn button on the
garage door opener. The LED will light.
? ? ? ?
_ _ _ _
3.Enter a 4-digit personal identification number (PIN) of
your choice on the keypad.
4.Press and hold the ENTER button. Check to see if
the opener light blinks. Release the ENTER button
after the light bulb blinks.
4
Press and hold
the enter button
Opener light bulbs
blink
To change an existing keyless entry PIN:
1.Enter the existing programmed PIN that you want to
change.
2.Press and hold the # button until the light bulb blinks
twice.
After the lights
blink release the
ENTER button
3.Enter the new 4-digit PIN of your choice, then press
the ENTER button. The light bulb will blink once.
4.To test, enter the new PIN, then press the ENTER
button. The garage door opener will activate.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION OF YOUR OPENER
CARE OF YOUR OPENER
When properly installed, your opener will operate
with minimal maintenance. The opener does not
require additional lubrication.
Your opener can be activated by any of the following
devices:
Limit and Force Settings: These settings must be
checked and properly set when the opener is
installed. Weather conditions may cause some
minor changes in the door operation, requiring
some re-adjustments, particularly during the first
year of operation. Refer to limit and force setting in,
section 13.
• The ACTIVATION button
Press the button until door starts to move.
• The wall control, outside keyswitch or keyless
entry system (if you have installed any of these
accessories).
Follow the instructions carefully and repeat the
safety reverse test after any adjustment.
• The Transmitter or Wireless Wall
Control (E128M)
Hold the push button down until the door starts to move.
Transmitter: Additional transmitters can be
purchased at any time. Refer to Accessories. Any
new transmitters must be programmed into the
opener.
When the opener is activated by transmitter,
ACTIVATION button or wall control:
Transmitter battery: If transmission range
decreases, replace the battery.
• If open, the door will close. If closed, the door will open.
• If closing, the door will stop.
• If opening, the door will stop (allowing space for entry
and exit of pets and for fresh air).
MAINTENANCE OF YOUR OPENER
• If the door has been stopped in a partially open or
closed position, it will reverse direction.
Once a Month:
• Repeat safety reverse test.
Make any necessary adjustments
(section 13).
Obstruction behaviour:
• Manually operate door. If it is unbalanced or
binding, call for professional garage door
service.
• If an obstruction is encountered while closing, the door
will reverse.
• If an obstruction is encountered while opening, the door
will reverse and stop.
• The optional Protector System™ uses an invisible beam
which, when broken by an obstruction, causes a closing
door to open and prevents an open door from closing. It
is STRONGLY RECOMMENDED for homeowners with
young children.
• Check to be sure door opens and closes fully.
Set limits and/or force if necessary.
SPECIFICATIONS MR850EVO
Input Voltage:
Rated Load:
Max.Pull Force:
Standby Power:
Drive:
230-240 VAC, 50 Hz, 170 W
Door should be fully closed if possible.
Weak or broken springs could allow an
open door to fall rapidly. Property damage
or serious personal injury could result.
32 Nm
550 N @ O300 mm
<1 Watt
DC gearmotor permanent
lubrication
Opening the door manually:
Max. Drum Rotations:
Memory Registers:
41/
64
2
The door can be opened manually by pulling the
release cord down firmly.
Operating Frequency:
433.30/433.92/434.54 MHz
To re-engage the door, pull the release cord down firmly.
SPECIFICATIONS MR650EVO
The opener light will turn on:
Input Voltage:
Rated Load:
Max.Pull Force:
Standby Power:
Drive:
230-240 VAC, 50 Hz, 100 W
• when opener is initially plugged in;
• when the power is briefly interrupted;
• when the opener is activated.
• when IR Beams are triggered with the door in the
Open position.
25 Nm
500 N @ O300 mm
<1 Watt
(the light turns off automatically after 2-1/2 minutes.)
DC gearmotor permanent
lubrication
Max. Drum Rotations:
Memory Registers:
41/
64
2
Operating Frequency:
433.30/433.92/434.54 MHz
SPECIAL NOTE: Chamberlain strongly recommends that the Protector SystemTM be installed on all garage door openers.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
20 ACCESSORIES
7. Model CM1702 Outside quick release
8. Model C77 The Protector SystemTM (IR Beams)
9. Model E475M-12 V Standby Power Unit (battery
backup) - (MR850 only)
1. Model E128M 2 Channel wireless wall button
2. Model E940M 1 Channel transmitter
3. Model E943M 3 Channel transmitter
4. Model E945M 3 Channel mini transmitter
5. Model E840M Keyless entry system
6. Model 760 Outside keyswitch
10. Model SRDLK01-12 V Solenoid roller door lock -
(MR850 only)
5
4
3
1
2
8
9
7
6
10
21
TYPICAL WIRING DIAGRAM MR850EVO/650EVO -
Information for Service Personnel
MR850EVO ONLY
External
Device
12 vdc
gnd
no
com
Keyswitch or
push button
rx
white/black
white
white/black
white
13
Download from Www.Somanuals.com. All Manuals Search And Download.
22
SPECIAL FEATURES - Information for Service Personnel
(OPTIONAL ACCESSORIES)
1. Solenoid roller door lock (SRDLK01-12 V) - (MR850EVO only)
2. 12 VDC power output for external devices - (MR850EVO only)
TM
3. The Protector System IR Beams - C77
4. LCD Motion detecting control - C198
5. Standby Power Unit (battery backup E475-12 V) - (MR850EVO only)
1
2
MR850EVO ONLY
4
3
5
14
Download from Www.Somanuals.com. All Manuals Search And Download.
23 SPARE PARTS - Information for Service Personnel
041A6811-2
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons
in order to avoid hazard.
001A6621
041A6812
026B0166
041B0655
041D7403 (MR850)
041D7403-1 (MR650)
001A6528
204D0250 (MR850)
204D0251 (MR650)
001B6681
002B1600
041B0641 (MR850)
041B0641-1 (MR650)
041B0640 (MR850)
041B0640-1 (MR650)
041A7460 (MR850)
041A7460-1 (MR650)
041A6811-2
Mount plate sub assembly MR850 (including motor)
Sungear kit
Front upper housing
Base housing MR850
Base housing MR650
041A6812
041B0655
041B0640
041B0640-1
041D7403
041D7403-1
041A7460
041A7460-1
041B0641
041B0641-1
204D0250
204D0251
001A6621
001B6681
001A6528
002B1600
026B0166
PCB for MR850
PCB for MR650
Front cover sub assembly MR850
Front cover sub assembly MR650
Hinged access cover MR850
Hinged access cover MR650
230V 105VA transformer for MR850
230V 80VA transformer for MR650
Clamp & bolt assembly
Handle & pull rope assembly
Absolute Position Encoder (APE)
Weight Bar
Power Cord
15
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals1.co7m. All Manuals Search And Download.
TROUBLESHOOTING
• Repeat the limit and force setting in section 13.
Repeat safety reverse test after adjustments.
9. The opener strains to operate door:
• The door may be out of balance or the springs may
be broken. Close the door and use the manual
release to disconnect the door. Open and close the
door manually. A properly balanced door will stay in
any point of travel while being supported entirely by
its springs. If it does not, disconnect the opener and
call a trained door systems technician.
10. The opener motor hums briefly, then will not
work:
1. The opener will not operate from either the
ACTIVATION button or the transmitters :
• Does the opener have electric power? Plug a lamp into
the outlet. If it does not work, check the fuse box.
• Have you disabled all door locks? Review installation
instruction warnings on page 1.
• Is there a build-up of ice or snow under the door? The
door may be frozen to the ground. Remove any
restriction.
• The garage door spring may be broken. Have it
replaced.
2. Opener operates from the transmitter, but not
from the wired wall control (optional accessory):
• Is the wall control lit? If not, reverse the two wires. If
the opener runs, check for a faulty wire connection at
the wall control, a short under the staples, or a broken
wire.
• Check that the door is not in manual release mode
(refer section 8).
• The garage door springs may be broken. See above.
• If the problem occurs on the first operation of the
opener, door may be locked. Disable any door locks.
11. The opener will not operate due to power
failure:
• Are the wiring connections correct? Refer to wired wall
control instructions.
• Use the manual release handle to disconnect the
door. The door can be opened and closed manually.
When power is restored, re-engage the opener (refer
section 8).
• If a Battery Back up Unit is connected, the opener
should be able to operate up to 20 times without
power.
3. The door operates from the ACTIVATION button
or wired wall control, but not from the wireless
wall control or transmitter:
• If the wired wall control is installed and it is flashing,
ensure the lock feature is off.
• Program the opener to match the transmitter code.
(Refer to section 18). Repeat with all transmitters.
4. The transmitter has short range:
• Change the location of the transmitter in your car.
• Check to be sure the antenna on the bottom of the
opener extends fully downward.
• Some installations may have shorter range due to a
metal door, foil backed insulation, or metal garage
siding.
5. The garage door opens and closes by itself:
• Be sure that all transmitter push buttons are off.
• If the wired wall control (optional accessory) is
installed, remove the bell wire from the wired wall
control terminals and operate from the ACTIVATION
button or transmitter . If this solves the problem, the
wired wall control is faulty (replace), or there is an
intermittent short on the wire between the wired wall
control and the opener.
• Clear memory and re-program all wireless wall
controls and transmitters.
6. The door reverses and stops before opening
completely:
• Is something obstructing the door? Is it out of balance,
or are the springs broken? Remove the obstruction or
repair the door.
7. The door reverses for no apparent reason and
opener lights blink 10 times after reversing:
• Check the Protector SystemTM (IR Beams), if
installed. Correct alignment if the red light on the beam
is solid.
8. The door opens but will not close or reverses
while closing:
• Is something obstructing the door? Pull the manual
release handle. Operate the door manually. If it is
unbalanced or binding, call a trained door systems
technician.
• Clear any ice or snow from the garage floor area where
the door closes.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAMBERLAIN LIMITED WARRANTY
Merlin Professional MR850EVO/MR650EVO
Roller Garage Door Opener
This Chamberlain Limited Warranty does not cover any failure of, or defect
in, the Unit due to:
1
non-compliance with the instructions regarding installation, operation,
maintenance and testing of the Unit or of any product with which the Unit is
used;
Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited
(Chamberlain), the manufacturer of Merlin® automatic garage door openers,
is committed to manufacturing and supplying high quality goods. As part of
this commitment, we seek to provide reliable service and support for our
goods and are pleased to provide you, the original purchaser, with this
Chamberlain Limited Warranty.
2
any attempt by a person other than a Professional Dealer to repair,
dismantle, reinstall or move the Unit to another location once it has been
installed;
3
tampering, neglect, abuse, wear and tear, accident, electrical storm,
excessive use or conditions other than normal domestic use;
problems with, or relating to, the garage door or garage door hardware,
4
We also provide the following statement as required by the Australian
Consumer Law: In Australia, in addition to your rights under this
Chamberlain Limited Warranty, our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and
the failure does not amount to a major failure.
including but not limited to the door springs, door rollers, door alignment or
hinges;
5
problems caused by electrical faults or replacement of batteries or light
bulbs;
6
7
8
water or moisture ingress that causes corrosion or electrical malfunction;
corrosion caused by sea air if located near a waterway, beach etc; or
fitment to a commercial door or in a commercial operating application.
NB: A General Purpose Outlet (GPO) ie: power point must be supplied by the
consumer as this electrical fitting does not form a part of the Unit (opener).
Chamberlain’s warranty
Chamberlain warrants to the original purchaser of the following Merlin®
Roller Door Openers:
If this Chamberlain Limited Warranty does not apply, you may have rights
available to you under the Australian Consumer Law.
Merlin® MR850EVO Roller Door Opener (Unit) that all parts of the Unit,
other than remote controlled transmitters and accessories, globes and
batteries, are free from defects in materials and workmanship for a period of
60 months or 15,000 cycles (opening & closing of the garage door)
whichever comes first, from the date of purchase when installed in a
residential premise with a residential specified garage door that is designed
for the sole purpose of domestic domicile.
Liability – Australia only
Except as set out in the Australian Consumer Law (being Schedule 2 of the
Competition and Consumer Act 2010) (as amended, consolidated or
replaced):
1
all other guarantees, warranties and representations in relation to the Unit
or its supply are excluded to the extent that Chamberlain can lawfully exclude
them; and
Merlin® MR650EVO Roller Door Opener (Unit) that all parts of the Unit,
other than remote controlled transmitters and accessories, globes and
batteries, are free from defects in materials and workmanship for a period of
24 months or 5,000 cycles (opening & closing of the garage door) whichever
comes first, from the date of purchase when installed in a residential premise
with a residential specified garage door that is designed for the sole purpose
of domestic domicile.
2
under no circumstances will Chamberlain be liable for consequential,
incidental or special damages arising in connection with the use, or inability
to use, the Unit, other than those which were reasonably foreseeable as
liable to result from the failure.
Liability – New Zealand only
Except as set out in the Fair Trading Act 1986 and the Consumer Guarantees
Act 1993 (as amended, consolidated or replaced):
1
all other guarantees, warranties and representations in relation to the Unit
Chamberlain warrants that remote controlled transmitters and accessories
included with the Unit are free from defects in materials and workmanship for
a period of 12 months from the date of purchase.
or its supply are excluded to the extent that Chamberlain can lawfully exclude
them; and
2
under no circumstances will Chamberlain be liable for consequential,
incidental or special damages arising in connection with the use, or inability
to use, the Unit, other than those which were reasonably foreseeable as
liable to result from the failure.
Batteries and globes are not covered under the Chamberlain Limited
Warranty.
It is a condition of this Chamberlain Limited Warranty that the Unit is sold,
installed and serviced by a Professional Dealer appointed by Chamberlain. A
Merlin® branded garage door opener purchased over the internet and
installed by a person other than a Professional Dealer will not be covered by
this Chamberlain Limited Warranty. It is also a condition of the Chamberlain
Limited Warranty that the Unit is serviced by a Professional Dealer during the
period 24 months to 36 months after the initial installation date. The garage
door service fee will be at the purchaser’s expense.
Note
We request that you retain your sales docket or invoice as proof-of-purchase
and attach it to this manual to enable you to establish the date of purchase in
the unlikely event of a warranty service being required. Chamberlain
reserves the right to change the design and specifications of the Unit without
prior notification. Some features or accessories of the Unit may not be
available in certain markets or areas. Please check with your distributor.
Chamberlain service centre contact details
Australia
During the applicable Chamberlain Limited Warranty period, if you are
concerned that the Unit may be defective, for prompt on-site service call the
Professional Dealer that sold/installed the opener, or our service centre on
the toll free number below and a Chamberlain technician will diagnose the
problem and arrange for this to be rectified. Once the problem has been
diagnosed, subject to your rights under the Australian Consumer Law with
respect to major failures, Chamberlain or its Professional Dealer will provide
you with:
Phone toll free 1800 638 234
Fax toll free 1800 888 121
Chamberlain Australia Pty. Ltd.
PO BOX 1446
Lane Cove NSW 1595
1. repairs to the Unit
or
New Zealand
2. a replacement Unit.
Auckland phone 09 477 2823
Phone toll free 0800 653 667
Fax toll free 0800 653 663
Repairs and replacement parts provided under this Chamberlain Limited
Warranty are provided free of charge and are warranted for the remaining
portion of the original warranty period.
Email: [email protected]
This Chamberlain Limited Warranty provides benefits which are in addition to
your other rights and remedies as a consumer.
Exclusions
If our service centre determines that a warranty claim has been made in
respect of a failure or defect arising under or out of any exclusion detailed
below such that the claim is not covered under this Chamberlain Limited
Warranty, we may, subject to your other rights and remedies as a consumer,
charge you a fee to repair, replace and/or return the Unit to you.
TM
Trademark of The Chamberlain Group, Inc.
® Registered Trademark of The Chamberlain Group, Inc.
© 2012 The Chamberlain Group, Inc
19
114A4209D
Download from Www.Somanuals.com. All Manuals Search And Download.
|