DV 770 .. - Built Under Double Oven
Manual for Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Before Using for the First Time
– Read the instructions carefully before installing and using the appliance.
– After unpacking the appliance, check that it is not damaged. In case of doubt, do not use the appliance
and contact your supplier or a qualified engineer.
– Removeallthepackingmaterials(i.e. plasticbags, polystyrenefoam, etc.)anddonotleaveitaroundwithin
easy reach of children, as these may cause serious injuries. The packaging materials are recyclable.
– Do not attempt to modify the technical characteristics of the appliance, as it may become dangerous
to use.
– The appliance should be installed and all the electrical connections made by a qualified engineer in
compliance with local regulations in force and following the manufacturer's instructions.
Important Precautions and Recommendations
for Use of Electrical Appliances
Use of any electrical appliance implies the necessity to follow a series of fundamental rules. In particular:
– never touch the appliance with wet hands or feet;
– do not operate the appliance barefooted;
– do not allow children or disabled people to use the appliance without your supervision.
The manufacturer cannot be held responsible for any damages caused by improper, incorrect or
unreasonable use of the appliance.
Using the Double Oven for the First Time
You are advised to carry out the following operations:
– Assemble the interior of the top and the lower ovens as described under the heading “Cleaning and
maintenance”
– Switch the empty ovens ON at maximum temperature for about two hours to eliminate traces of grease
and smell from the components.
– Let the ovens cool down, switch off the electrical supply, then clean the inside of the ovens with a cloth
soaked in water and neutral detergent and dry thoroughly.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Important Safeguards and Recommendations
– Do not carry out any cleaning or maintenance without first disconnecting the appliance from the
electrical supply.
– During and after use of the double oven, certain parts will become very hot. Do not touch hot parts.
– After use always ensure that the controls are in the OFF position.
– Household appliances are not intended to be played with by children.
– Keep children away from the oven during use.
– Children, or persons with a disability which limits their ability to use the appliance, should have a
responsible person to instruct them in its use. The instructor should be satisfied that they can use the
appliance without danger to themselves or their surroundings.
– WARNING
When correctly installed, your product meets all safety requirements laid down for this type of product
category. However special care should be taken around the rear or the underneath of the appliance
as these areas are not designed or intended to be touched and may contain sharp or rough edges, that
may cause injury.
– Fire Risk! Do not store inflammable materials inside the ovens.
– Always use oven gloves when removing the shelves and food trays from the oven whilst hot.
– Clean the ovens regularly and do not allow fat or oils to build up in the oven base or trays. Remove
spillages as soon as they occur.
– Do not line the oven walls with aluminium foil. Do not place baking trays or the drip tray on the base
of the oven chambers.
– Always stand back from the double oven when opening the oven doors to allow steam and hot air to
escape before removing the food.
– Do not hang towels, dishcloths or other items on the double oven or its handles – as this could be a
fire hazard.
– Make sure that electrical cords connecting other appliances in the proximity cannot become entrapped
in the oven doors.
– Before disposing of an unwanted appliance, it is recommended that it is made inoperative and that all
potentially hazardous parts are made harmless.
– Important: This appliance has been designed for domestic use only. The appliance is NOT suitable for
use within a semi-commercial, commercial or communal environment.
– Safe food handling: leave food in the oven for as short a time as possible before and after cooking.
This is to avoid contamination by organisms which may cause food poisoning. Take particular care
during warmer weather.
– Do not operate your appliance by means of an external timer or separate remote-control system.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Top Oven Controls
Controls Description
1. Temperature knob
2. Cooking functions knob
3. Top oven power ON indicator lamp
4. Top oven temperature indicator lamp
4
1
3
2
Fig. 1
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Top Natural Convection Electric Oven
General Features
This oven features 2 different thermostatic control functions to satisfy all
cooking requirements, provided by 3 heating elements:
– Upper element, 700 W
– Lower element, 1000 W
– Grill element, 2000 W
Note:
Whenusingforthefirsttime, youareadvisedtooperatetheovenatmaximum
temperature (thermostat knob on the maximum position) for approximately
one hour in the
mode and for another 15 minutes in the
mode in
order to eliminate any traces of grease from the electrical elements.
Operating Principles
Heating and cooking in the natural convection oven are obtained:
a. by Normal Convection
The heat is produced by the upper and lower heating elements.
b. by Radiation
The heat is radiated by the infra red grill element.
Attention: the oven door becomes very hot during operation.
Keep children away.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
How to Use the Top Oven
WARNING: The door is hot, use the handle.
ATTENTION - MOST IMPORTANT
Pay special attention not to touch the hot heating element inside the oven cavity.
Fig. 2
Fig. 3
Thermostat Knob (Fig. 2)
This only sets the cooking temperature and does not switch the oven on.
Rotate clockwise until the required temperature is reached (from 50 °C to 250 °C).
The thermostat indicator light will illuminate when the oven is switched on and turns off when the oven
reaches the correct temperature.
The light will cycle on and off during cooking in line with the oven temperature.
Function Selector Knob (Fig. 3)
Rotate the knob clockwise to set the oven for one of the following functions:
Oven Light
By turning the function selector knob to this setting, the oven light will illuminate in the oven cavity.
The oven light will operate on all selected functions.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Traditional Convection Cooking
The upper and lower heating elements come on. The heat is dispersed by natural convection and the
temperature must be set to between 50 °C and 250 °C with the thermostat knob.
The oven must be preheated before cooking.
Recommended for:
Food that requires the same degree of cooking both inside and out, for example roasts, spare pork ribs,
meringues etc.
Traditional Grilling
The infrared grill element comes on. The heat is dispersed by radiation.
Use with the oven door closed and the thermostat knob to position 225 °C for max 15 minutes, then to
position 175 °C.
For cooking hints, see the chapter “USE OF THE GRILL”.
Recommended for:
Intense grilling, browning, cooking au gratin and toasting etc.
It is recommended that you do not grill for longer than 30 minutes at any one time.
Caution: the oven door becomes very hot during operation. Keep children well out of reach.
Oven Cooking
Before introducing the food, preheat the oven to the desired temperature.
For a correct preheating operation, it is advisable to remove the tray from the oven and introduce it
together with the food, when the oven has reached the desired temperature.
Check the cooking time and turn off the oven 5 minutes before the theoretical time to recuperate the
stored heat.
Use of the Grill
– Preheat the oven for about 5 minutes with the door closed.
– Introduce the food to be cooked, positioning the rack as close to the grill as possible.
– The dripping pan should be placed under the rack to catch the cooking juices and fats.
Grilling with the oven door closed.
It is recommended that you do not grill for longer than 30 minutes at anyone time.
Attention: the oven door becomes very hot during operation.
Keep children away.
The external parts of the oven become hot during operation.
Keep children well out of reach.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Lower Main Oven Controls
Controls Description
1. ON/OFF selection
2. Temperature and programmer functions regulation, Childlock selection
3. Programmer functions selection
4. Oven functions selection
5. Functions display
6. Clock/Programmer display
7. Temperature display
7
6
5
4
Fig. 4
1
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Lower Main Full Electronic Multifunction
Oven
General Features
This multifunction oven has 4 heating elements which allow you to choose between 9 cooking
programmes:
– Lower element
– Upper element
– Grill element
1000 W
900 W
2000 W
1900 W
– Circular element
Note:
Before using your new oven, it is necessary to condition your oven.
Heat the oven on maximum for 60 minutes in the position
eliminate possible traces of grease on the heating elements.
and
(for another 60 minutes) to
Thenheattheovenforanother15minutesinthegrillposition
GRILL COOKING and GRILLING AND “AU GRATIN”.
asexplainedinthechaptersVENTILATED
IMPORTANT
Do not touch the hot heating elements inside the oven cavity.
Attention: the oven door becomes very hot during operation. Use the handle. Keep children
away.
“Touch-control” keys
The “touch-control” keys shall be operated by the fingers (just by touching the key).
When using touch controls it is best to use the ball of your finger rather than the tip.
Fig. 5b
Fig. 5a
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Operating Principles
Heating and cooking in the FULL ELECTRONIC MULTIFUNCTION oven are
obtained in the following ways:
a. by Normal convection
The heat is produced by the upper and lower heating elements.
b. by Semi-Forced Convection From The Bottom
The heat produced by the lower heating element is distributed throughout the oven by the fan.
c. by Radiation
The heat is radiated by the infrared grill element.
d. by Double Radiation
The heat is radiated by the infrared grill and the top heating elements.
e. by Radiation and Ventilation
The radiated heat from the infrared grill element is distributed throughout the oven by the fan.
f. by Semi-Forced Convection From The Bottom And Back
The food is defrosted by using the fan only function without heat.
g. by Forced Convection
The air inside the oven is warmed by a circular heating element at the back of the oven. Hot air is then
moved around the oven by a fan near the heating element. Food can be placed inside a cold oven
because it heats up quickly. The heat is evenly distributed throughout the oven allowing for different
dishes to be cooked simultaneously.
h. by Semi-Forced Convection
The heat produced by the upper and lower heating elements is distributed throughout the oven by the
fan.
i. by Ventilation
1. “dEF” food is defrosted by using the fan only.
2. By using “dEF” and setting the temperature (from 40° to 100°C maximum) the lower heating element
is activated and this function can be used to keep food warm (for a limited amount of time).
l. by Fast Pre-heating (BOOSTER)
This special program allows (by a combination of the heating elements) a fast pre-heating of the oven
cavity.
Attention: the oven door becomes very hot during operation.
Keep children away.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Using the Lower Main Oven - Electronic Display
DIGITS
SYMBOL
Lit = minute minder in operation
Flashing = countdown completed
by the minute minder
- Oven switched on: Time of day and
selected function (alternating)
- Oven switched off: Time of day
SYMBOL
Lit = operation of heating elements
(cooking functions)
SYMBOL
Lit = semi-automatic or automatic cooking
programmed
Flashing = semi-automatic or automatic
cooking completed
Flashing = semi-automatic or automatic
cooking completed
Fig. 6
SYMBOL
Programmer functions - Progressive selection
(each time the key is touched)
SYMBOL
ON/OFF
OVEN SWITCHED OFF
OVEN SWITCHED ON
Time of day and
selected function
(alternating)
Time of day
NORMAL
STATUS
NORMAL STATUS
SYMBOL
To decrease the numbers
on the display or to set
the alarm sound
st
st
1
1
Timer
Timer
Oven light
options
Duration of a
nd
nd
2
2
cooking program
Automatic
switch off
options
Stop time of a
rd
rd
3
4
3
cooking program
SYMBOL
Setting time
of day
th
To increase the numbers
on the display
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Electronic Controller Features
It performs the following functions:
– 24 hours clock with illuminated display.
– Timer (minute minder: up to 600 minutes - 10 hours).
– Programme for semi-automatic oven cooking (up to 600 minutes - 10 hours - of cooking time).
– Programme for automatic oven cooking (up to 600 minutes - 10 hours - of cooking time).
– Automatic switch off.
– “Childlock” safety (deactivation of the controller selections).
– Oven functions and temperature selection.
– Each setting is automatically processed about 4 seconds after the last selection.
IMPORTANT NOTE: The first time the oven is used or after a power failure the clock is automatically set
to 12:00 (“12:00” appears on the clock/programmer display).
WARNING: The oven can be used but it is preferable to set the time of the day.
Setting Time of Day
The controller is provided with an electronic clock with illuminated figures showing the hour and
minutes.
IMPORTANT: The time of day can be set only when the oven is turned off (“stand-by”
condition).
To set the time:
– Select “hour” on the clock/programmer display by using the key “ ”.
– While the hour is flashing touch “ ” and “ ” keys to set the time.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Turning the Oven On and Off
To turn the oven ON:
– Touch the key “ ” and hold until “On” appears on the clock/programmer
display.
– You can now operate your oven. The time of the day appears on the clock/programmer display (followed
by the programme number “Pr01, Pr02, ...”).
To turn the oven OFF:
– Touch the key “ ” and hold until “OFF” appears on the clock/programmer display.
– The oven is turned off (“stand-by” condition) and the time of the day appears on the clock/programmer
display.
– 3 beeps indicate that the oven has been turned off.
To select the volume of the beeps, touch the “ ” key when the oven is turned off (”stand-by”
condition).
WARNING - IMPORTANT NOTE
Do not turn the oven off if you have set it for automatic or semi-automatic cooking. This
operation will cancel the programmed cooking.
Only the timer (minute minder) operates in the “stand-by” condition.
Oven Automatic Switch Off
– If you do not use your oven within 3 minutes, it automatically switches back to stand-by.
– When the oven is operating a cooking function it automatically switches back to stand-by after 10
hours.
– It is possible to remove the automatic switch off feature by selecting “A_SO” (by using the key “
”
with the oven switched off) on the clock/programmer display and then touching the “ ” or “ ” key
to set “OFF”.
To reactivate the automatic switch off feature repeat the same procedure and set to “On”.
It is factory setted for “A_SO - On” (automatic switch off ON) and this option is also automatically
activated after a power failure.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Childlock Safety
To activate the Childlock option touch the “ ” and “ ” keys
simultaneously and hold until the clock/programmer display
shows “n--0” and then “On”.
Then the time of the day appears again (followed by the selected
programme number “Pr01, Pr02, ...” when the oven is ON). The
temperature display shows “ ”.
When the Childlock option has been selected it is only possible to
turn off the oven (stand-by mode) and operate the timer (minute
minder).
In this setting it is not possible to change the oven cooking
programme (cooking function, temperature) and the time
selected for a semi-automatic or automatic cooking: if touching
the relative keys “n--0” appears on the central display.
If the oven is turned off (stand-by mode) it is only possible to
operate the timer.
To deactivate the “Childlock” option touch the “ ” and “
”
keys simultaneously and hold until the clock/programmer display
shows “n--0” and then “OFF”.
Then the time of the day appears again (followed by the selected
programme number “Pr01, Pr02, ...” when the oven is ON). On
the temperature display the “ ” symbol goes out.
Fig. 7
IMPORTANT: If the oven has been switched OFF (stand-by mode) with the Childlock option
selected it is possible to turn ON the oven only after having deactivated the Childlock.
Using The Timer (Minute Minder)
You can use the timer at any time, even when the oven is not in use or switched off (stand-by mode). The
timer does not turn the oven off. Remember to turn off the oven manually. The timer can be set for up
to 600 minutes (10 hours).
To set the timer:
– Select “bELL” on the clock/programmer display by using the key “ ” and then, with “----” flashing on
the central display, touch “ ” and “ ” keys and set the time in minutes.
– To reset the time touch the “ ” or “ ” key.
– Then the time of the day appears again on the clock/programmer display (followed by the selected
programme number “Pr01, Pr02, ...” when the oven is ON) and the countdown starts immediately.
– To check the countdown select “bELL” on the clock/programmer display by using the key “ ”; the
time is indicated (for a few seconds) in minutes.
– When the time is up, the timer will beep. Touch any key (except the “ ” key) to turn it off.
NOTE:
The timer also operates if the oven, after selection, is turned OFF (stand-by mode). The timer
can also be set in the stand-by mode (OFF).
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Using the Lower Main Oven
Selecting the Cooking Functions
Clock/
Programmer
Display
Functions
Display
Setting
Oven Cooking Function
When selection a cooking function the
relative programme number and the
symbol are activated.
Setting
Fig. 8
Set Oven Function Key
Decreasing
Set Oven Function Key
Increasing
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Using the Lower Main Oven
Selecting the Temperature
Cooking Temperature
All cooking functions start to operate with a pre-set temperature which can be modified, at any time, by
touching the relative “+” and “–” keys positioned below the temperature display.
“Celsius Degrees” Symbol
The symbol is lit when the temperature is displayed.
Childlock Symbol
When the symbol is permanently lit the Childlock option is activated.
Pre-heating Indicators
When the oven is operating a cooking function
these indicate the time remaining (%) for completing
the pre-heating.
Time remaining > 75%
Time remaining between 50 and 75%
Time remaining between 25 and 50%
Time remaining < 25%
Pre-heating completed
Residual Heat Indicators
When a cooking function is switched off or the oven is
switched off ("stand-by" mode), these indicate that the
oven cavity is still hot.
Temperature above 200 °C
Temperature between 150 and 200 °C
Temperature between 100 and 150 °C
Temperature between 50 and 100 °C
Temperature less than 50 °C
Fig. 9
Set Oven Temperature Key
Set Oven Temperature Key
Decreasing
Increasing
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Using the Lower Main Oven
Cooking Functions
Turn on the oven as indicated in the “TURNING THE OVEN ON AND
OFF” chapter. Select the oven function and temperature as indicated in
the previous pages.
IMPORTANT: the cooking function and temperature can be modified at any time during the
normal, semi-automatic or automatic cooking.
Please remember to set the Childlock option in the presence of children.
Oven Lamp
When the oven is turned ON the oven light comes on and the relative symbol is lit in the functions display.
The clock/programmer display reads the time of the day and alternates with “Pr01”.
The oven light remains on in all cooking modes. The lamp is automatically switched off about three
minutes after competing the pre-heating time. During automatic cooking, the lamp is switched off before
the oven starts to operate.
By pressing any key (not “ ”) the lamp is lit for about one minute.
Oven light automatic swich off.
It is possible to deactivate/activate this option (only when the oven is in the “stand-by” OFF mode):
– select “bulb” on the clock/programmer display by using the key “ ”;
– touch “ ” or “ ” key to select “on” (for automatic switch off) or “off” (for oven lamp always on).
Automatic switch off “bulb ON” has been set by the factory and this option is automatically activated
after a power failure.
Traditional Convection Cooking
The upper and lower heating elements are switched on.
The heat is diffused by natural convection and the temperature must be set between 50 and 250°C.
The pre-heating temperature is set at 200°C.
To change the temperature, follow the instructions in the “SELECTING THE TEMPERATURE” chapter.
Recommended for:
For foods which require the same cooking temperature both internally and externally, i.e. roasts, spare
ribs, meringue, etc.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Fan Lower Heat
The lower heating element and the fan motor are switched on.
The heat coming from the bottom is diffused by forced convection and the temperature must be set
between 50 and 250°C.
The pre-heating temperature is set at 190°C. To change the temperature, follow the instructions in the
“SELECTING THE TEMPERATURE” chapter.
Recommended for:
This mode is particularly suitable to complete cooking of dishes that require higher temperature at the
bottom.
Grilling
The infrared heating element is switched on.
The heat is diffused by radiation.
Use with the oven door closed and the temperature between 50 and 225°C maximum.
The pre-heating temperature is set at 225°C. To change the temperature, follow the instructions in the
“SELECTING THE TEMPERATURE” chapter.
Recommended for:
Intense grilling action for browning, crisping, “au gratin”, toasting, etc.
For correct use see the “USE OF THE GRILL AND TURBO GRILL” chapter.
The external parts of the oven become hot during operation.
Keep children well out of reach.
Turbo Grill
In this position the upper heating element and the grill element are switched on simultaneously. Heat is
radiated over the entire surface area of the grill.
Use with the oven door closed and the temperature between 50 and 225°C maximum.
The pre-heating temperature is set at 225°C. To change the temperature, follow the instructions in the
“SELECTING THE TEMPERATURE” chapter.
Recommended for:
Intense grilling action for browning, crisping, “au gratin”, toasting, etc.
For correct use see the “USE OF THE GRILL AND TURBO GRILL” chapter.
The external parts of the oven become hot during operation.
Keep children well out of reach.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Ventilated Grill Cooking
The infrared heating element and the fan are switched on.
The heat is mainly diffused by radiation and distributed by the fan throughout the oven.
Use with the oven door closed and the temperature between 50 and 200°C maximum.
The pre-heating temperature is set at 200°C. To change the temperature, follow the instructions in the
“SELECTING THE TEMPERATURE” chapter.
Recommended for:
For fast browning and sautéing , i. e. veal steak, steak, hamburger, etc.
For correct use see the “GRILLING AND AU GRATIN” chapter.
The external parts of the oven become hot during operation.
Keep children well out of reach.
Hot Air Cooking with Lower Heat
This mode combines the lower heating element, the circular heating element and the fan. The food is
cooked by forced air circulation with additional heat from the bottom of the oven. The temperature can
be set between 50 and 250°C.
The pre-heating temperature is set at 210°C. To change the temperature, follow the instructions in the
“SELECTING THE TEMPERATURE” chapter.
Recommended for:
This cooking mode is ideal for large joints of meat and large quantities of food that call for uniform
cooking inside and out, e.g. roasts, turkey, chicken, cakes, etc.
Hot Air Cooking
The circular heating element and the fan are switched on.
The heat is diffused by forced convection and the temperature can be set between 50 and 250°C.
The pre-heating temperature is set at 175°C. To change the temperature, follow the instructions in the
“SELECTING THE TEMPERATURE” chapter.
Recommended for:
For foods that must be well done on the outside and tender or rare on the inside, i. e. lasagna, lamb, roast
beef, whole fish, etc.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Convection Cooking With Fan
The upper and lower heating elements and the fan are switched on. The heat
from the top and the bottom is diffused by fan convection. The temperature
can be set between 50 and 250°C.
The pre-heating temperature is set at 175°C. To change the temperature, follow the instructions in the
“SELECTING THE TEMPERATURE” chapter.
Recommended for:
For foods of large volume and quantity which require the same internal and external degree of cooking;
e.g. rolled roasts, turkey, legs, cakes, etc.
Defrosting Frozen Foods
or
Food Warming
The fan only switches on and the temperature display shows “dEF”.
It is possible to operate also the lower heating element (this function operates as a food warmer) by
regulating the temperature as indicated in the “SELECTING THE TEMPERATURE” chapter, from 40°C to
maximum 100°C (the temperature display shows the temperature).
Recommended for:
To rapidly defrost frozen food; 1 kilogram requires about one hour. The defrosting times vary according to
the quantity and type of food to be defrosted.
To keep hot cooked food at serving temperature.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Special “Booster” Programme
This special programme allow a fast pre-heating of the cavity by a
combination of the heating elements.
VERY IMPORTANT NOTE: This special programme must be
operated without food inside the oven cavity.
Introduce the food to be cooked only at the end of the
BOOSTER programme.
It is not possible to activate this option:
– If a semi-automatic or automatic cooking has been programmed.
– For the OVEN LAMP, GRILLING, TURBO GRILL and VENTILATED
GRILL COOKING functions.
– For the DEFROSTING FROZEN FOODS OR FOOD WARMING
function.
Fig. 10
To set the BOOSTER:
– Select the cooking function.
– Set the oven temperature.
– Touch the “ ” and “ ” keys simultaneously.
– With “b__r flashing on the clock/programmer display confirm the BOOSTER option by touching the
” key. If this key is not touched within 10 seconds this programme will not be activated.
“
During the BOOSTER program:
– The functions display shows the selected function.
– The clock/programmer display alternates between the selected programme number “Pr01, Pr02, ...”
and “b__r”.
– The selected temperature can be modified at any time.
– It is not possible to change the selected function which will start at the end of the BOOSTER programme.
If the selected function is changed the BOOSTER programme is automatically deactivated.
– It is not possible to select the programmer functions (timer, duration of a cooking program, stop time
of a cooking programme).
When the pre-heating temperature has been reached, three beeps will sound.
When the BOOSTER programme has been deactivated, another three beeps will sound (“b__r” no more
shown on the clock/programmer display).
To cancel the BOOSTER programme at any time before completing the fast pre-heating:
– Touch the “ ” or “ ” key (or simultaneously). The oven will proceed automatically to the selected
cooking function.
NOTE: during the BOOSTER programme the key “ ” is not active.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Using The Oven Manually
Turn the oven ON as indicated in the “TURNING THE OVEN ON AND OFF”
chapter.
Operate the oven manually by selecting the oven function and temperature
as indicated in the “SELECTING THE COOKING FUNCTIONS” and
“SELECTING THE TEMPERATURE” chapters. The oven will start to operate
about four seconds after your last selection.
If “A” symbol is shown on the clock/programmer display (semi-automatic or automatic cooking
selected), then you need to cancel the preset automatic cooking as indicated in the “CANCELLING A SET
PROGRAMME” chapter.
Turn OFF the oven as indicated in the “TURNING THE OVEN ON AND OFF” chapter.
Cancelling a Set Programme
To cancel a set programme (“A” symbol activated on the programmer display):
– Select “dur” on the programmer display by touching the key “ ” and then touch “ ” or “ ” key.
You should read “000'” on the clock/programmer display.
– A set programme is also cancelled when the oven is switched OFF in the “stand-by” mode. At the next
power up the oven is not programmed.
IMPORTANT: If the oven is ON, remember to switch it off manually otherwise it does not stop
operating in the set mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Using The Oven Automatically
Use automatic cooking to automatically turn the oven on, cook, and then
turn the oven off.
1. Check the clock shows the correct time.
2. Select the function and temperature. The oven will come on.
3. Decide how long the food will take to cook, allowing time for pre-heating if necessary.
4. Select “dur” (duration) on the clock/programmer display by using the “ ” key and then, with “---’”
flashing on the central display, touch “ ” or “ ” keys to set the time in minutes (maximum 600
minutes - 10 hours). To reset the cooking time touch the “ ” or “ ” key.
5. Decide the time you would like the oven to turn off; select “End” on the clock/programmer display by
using the “ ” key and then, with the time flashing on the central display, touch the “ ” or “ ” keys
to set the end of cooking time (hour and minutes).
If there is time to wait before cooking starts, “A” will show in the clock /programmer display and the oven
will switch off but is now set for automatic cooking.
If you are already at home to turn the oven on and only want the oven to turn off automatically, start
cooking as normal, then follow step 4 or step 5 to set a time to stop the oven.
When automatic cooking starts, “ ” will be displayed and the oven will turn on.
– To see the remaining cook time, follow step 4 up to display “dur” (duration).
– To see the set stop time, follow step 5 up to display “End”.
– To cancel automatic or semi-automatic cooking at any time see chapter “CANCELLING A SET
PROGRAMME”.
When the stop time is reached the timer will beep, “A” and “ ” will flash:
– Touch any key to stop the beeping.
– The oven will turn off on the “OVEN LIGHT” function.
– Turn OFF the oven as indicated in the “TURNING THE OVEN ON AND OFF” chapter.
Attention: after a power failure any automatic or semi-automatic programme is cancelled.
Turn off the oven manually.
During an automatic or semi-automatic cooking programme it is possible to change the
cooking function and the temperature at any time.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Cooking Advice
Sterilization
Sterilization of foods to be conserved, in full and hermetically sealed jars,
is done in the following way:
a. Set the switch to position
.
b. Set the thermostat knob to position 185 °C and preheat the oven.
c. Fill the dripping pan with hot water.
d. Set the jars onto the dripping pan making sure they do not touch each other and the door and set the
thermostat knob to position 135 °C.
When sterilization has begun, that is, when the contents of the jars start to bubble, turn off the oven and
let cool.
Reheat Food
Set the
function and the temperature at 150° C.
Bread becomes fragrant again if wet with a few drops of water and put into the oven for about 10
minutes.
Cooking Different Dishes at the Same Time
By setting the
same time.
or
functions the ventilated oven allows you to cook different types of food at the
Fish, cakes and meat can be cooked together without the smells and flavours mixing.
Please ensure that:
– The cooking temperatures must be as close as possible with a maximum difference of 20°-25°C between
the different foods.
– Different dishes must be placed in the oven at different times according to the cooking time required for
each one. This type of cooking obviously provides a considerable saving on time and energy.
Roasting
To obtain classical roasting, please remember:
– that it is advisable to maintain a temperature between 180 and 200 °C.
– that the cooking time depends on the quantity and the type of foods.
Use of the Grill and Turbo Grill
Choose
or
function and set the temperature between 50 and 225°C maximum.
Preheat for approximately 5 minutes with the door closed.
Put the grill pan as close to the grill as possible.
Always grill with the oven door closed.
Do not grill for longer than 30 minutes at any one time.
Attention: the oven door becomes very hot during operation. Keep children away.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Grilling and “Au Gratin”
Grilling may be done by selecting the function
completely envelops the food that is to be cooked.
because the hot air
Set the temperature between 50 and 200°C maximum and after having
preheated the oven, simply place the food on the grid.
Close the door and let the oven operate until grilling is done.
Adding a few dabs of butter before the end of the cooking time gives the golden “au gratin” effect.
Always grill with the oven door closed.
Do not grill for longer than 30 minutes at any one time.
Attention: the oven door becomes very hot during operation. Keep children away.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Do’s and do not’s
– Do always grill with the oven door closed.
– Do read the user instructions carefully before using the double oven for first time.
– Do allow the double oven to heat for one and a half hours, before using for the first time, in order to
expel any smell from the new oven insulation, without the introduction of food.
– Do clean your double oven regularly.
– Do remove spills as soon as they occur.
– Do always use oven gloves when removing food shelves and trays from the oven.
– Do not allow children near the double oven when in use.
– Do not allow fat or oils to build up in the oven trays, or oven base.
– Do not place cooking utensils or plates directly onto the oven base.
– Do not grill food containing fat without using the grid.
– Do not cover the grilling grid with aluminium-foil.
– Do not use the oven tray for roasting.
– Do not place hot enamel parts in water. Leave them to cool first.
– Do not allow vinegar, coffee, milk, saltwater, lemon or tomato juice to remain in contact with enamel
parts (inside the oven and on the oven tray).
– Do not use abrasive cleaners or powders that will scratch the surfaces and the enamel.
– Do not attempt to repair the internal workings of your double oven.
– Do remove the protective film before the first use.
– Fire risk! Do not store flammable material in the ovens.
For Your Safety
ATTENTION:
The product should only be used for its intended purpose which is for the
cooking of domestic foodstuffs.
Under no circumstances should any external covers be removed for servicing
or maintenance except by suitably qualified personnel.
The appliance gets
very hot, mainly
around the cooking
areas. It is very
important that
children are not
left alone in the
kitchen when you are
cooking.
Important Notes
Installation, and any demonstration, information or adjustments are not
included in the warranty.
The oven must be installed by a suitably qualified and registered person in
accordance with the relevant Standards.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Care and Maintenance
It is advisable to clean when the appliance is cold and especially for cleaning
the enamelled parts.
Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the
surfaces.
IMPORTANT:
Before any operation
of cleaning and
maintenance
disconnect the
appliance from the
electrical supply.
Avoid using cleaning products with a chlorine or acidic base.
WARNING
Whencorrectly installed, yourproduct meets all safetyrequirements
laid down for this type of product category. However special care
should be taken around the rear or the underneath of the appliance
as these areas are not designed or intended to be touched and may
contain sharp or rough edges, that may cause injury.
Inside of Oven
ATTENTION:
The oven should always be cleaned after use when it has cooled down.
The cavity should be cleaned using a mild detergent solution and warm water.
Suitable proprietary chemical cleaners may be used after first consulting with
the manufacturers recommendations and testing a small sample of the oven
cavity. Abrasive cleaning agents or scouring pads/cloths should not be used
on the cavity surface.
Let the oven cool
down and pay special
attention no to touch
the hot heating
elements inside the
oven cavity.
NOTE: The manufacturers of this appliance will accept no responsibility for
damage caused by chemical or abrasive cleaning.
Enamelled Parts
All the enamelled parts must be cleaned with a sponge and soapy water only
or other non-abrasive products.
Dry preferably with a micro fibre or soft cloth.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Stainless Steel, Aluminium, Painted Parts and Silk-screen
Printed Surfaces
CAUTION:
Do not use abrasive
substances or non-
neutral detergents as
these will irreparably
damage the surface.
Clean using an appropriate product. Always dry thoroughly.
Stainless steel surfaces: can be cleaned with an appropriate stainless steel
cleaner.
IMPORTANT: these parts must be cleaned very carefully to avoid scratching
and abrasion. You are advised to use a soft cloth and neutral soap.
Glass Control Panel
Clean using an appropriate product. Always dry thoroughly.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the control
panel since they can scratch the surface, which may result in shattering of the
glass.
CAUTION:
Do not use a steam
cleaner because the
moisture can get into
the appliance thus
make it unsafe.
CAUTION:
Do not store
flammable material
in the oven.
CAUTION:
Do not use harsh
abrasive cleaners or
sharp metal scrapers
to clean the oven
door glass since
they can scratch the
surface, which may
result in shattering
of the glass.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Replacing the Halogen Oven Lights
WARNING: Ensure the appliance is switched off before replacing the
lamp to avoid the possibility of electric shock.
– Let the oven cavity and the heating elements to cool down;
– Switch off the electrical supply;
– Remove the protective cover C (fig. 11);
– Replace the halogen lamp B with a new one suitable for high temperatures
having the following specifications: 230V and same power (check watt
power as stamped in the lamp itself) of the replaced lamp.
IMPORTANT WARNING: Never replace the bulb with bare hands;
contamination from your fingers can cause premature failure.
Always use a clean cloth or gloves.
– Refit the protective cover;
Note: Oven bulb replacement is not covered by your guarantee.
WRONG
CORRECT
C
B
Fig. 11
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Assembling and Dismantling of the Side Runner Frames
– Assemble the wire racks to the oven walls using the 2 screws (Figs. 12-14).
– Slide the tray and rack into the runners (Figs. 13-15). The rack must be fitted so that the safety catch,
which stops it sliding out, faces the inside of the oven.
– To dismantle, operate in reverse order.
Fig. 12
Fig. 13
Fig. 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 14
32
Oven Doors
Removing the Oven Doors
The oven doors can easily be removed as follows:
– Open the door to the full extent (fig. 16a).
– Open the lever A completely on the left and right hinges (fig.
16b).
– Hold the door as shown in fig. 16.
– Gently close the door (fig. 16c) until left and right hinge levers
A are hooked to part B of the door (fig. 16b).
– Withdraw the hinge hooks from their location following arrow
C (fig. 16d).
– Rest the door on a soft surface.
Fig. 16a
– To replace the door, repeat the above steps in reverse order.
A
A
B
Fig. 16b
Fig. 16c
C
Fig. 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 16d
33
Oven Doors - Removable Inner Pane of Glass
Cleaning the Panes of Glass
The oven doors are fitted with no. 2 panes:
- no. 1 outside;
- no. 1 inner;
To clean the panes on both sides it is necessary to remove the
inner pane as follows.
Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the oven door glass since they scratch the surface, which
may result in shattering of the glass.
Removing the Inner Pane of Glass
Fig. 17
1. Lock the door open:
– Fully open the oven door (fig. 17).
– Fully open the lever A on the left and right hinges (Fig 18).
– Gently close the door (Fig. 19) until the left and right hinges
are hooked to part B of the door (Fig. 18).
A
2. Remove the inner pane:
– Top oven door only: remove the seal G by unhooking the no.
3 fixing hooks (fig. 20).
B
– Gently pull out the inner pane of glass (Fig. 21).
– Clean the glass with an appropriate cleaner. Dry thoroughly,
and place on a soft surface.
Fig. 18
Now you can also clean the inside of the outer glass.
Fig. 19
G
Fig. 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 20
34
Replacing the Inner Pane of Glass
1. Make sure the door is locked open (see fig. 19).
2. Replace the inner pane:
– Check that the four rubber pads are in place (D in Fig. 22).
– Check that you are holding the pane the correct way. You
should be able to read the wording on it as it faces you.
– Insert the pane in the left E and right F slide guides (fig. 23),
and gently slide it to the retainers H (fig. 24).
– Top oven door only: reassemble the seal G in the correct way
(fig. 25) by hooking the no. 3 fixing hooks in the proper holes
(fig. 26).
D
Fig. 22
E
E
– Unlock the oven door by opening it completely and closing
the lever A on the left and right hinges (Fig. 27).
F
Fig. 23
H
G
Fig. 25
Fig. 24
The top oven
door has a
sealed gasket in
the top part.
Fig. 26
It is normal the opened gap between
the top edge of the inner glass and the
sealed gasket. This allows the cooling
air circulation.
A
The bottom
oven door has
not a sealed
gasket in the
top part.
Fig. 27
Download from Www.Somanuals.com. All Manuals Search And Download.
35
ADVICE FOR THE INSTALLER
Important
Appliance installation and maintenance must only be carried out by QUALIFIED TECHNICIANS
and in compliance with the local safety standards.
• Failure to observe this rule will invalidate the warranty.
• Always disconnect the appliance from the electrical supply before carrying out any maintenance
operations or repairs.
• The walls surrounding the oven must be made of heat-resistant material.
• Taking care NOT to lift the oven by the door handle.
WARNING
When correctly installed, your product meets all safety requirements laid down for this type
of product category.
However special care should be taken around the rear or the underneath of the appliance as
these areas are not designed orintended to be touched and may contain sharp or rough edges,
that may cause injury.
To Build in the Double Oven
• The appliance should be installed by a QUALIFIED INSTALLATION TECHNICIAN.
The appliance must be installed in compliance with regulations in force.
The built under double oven shall be fitted under the working surface into a kitchen base unit (width and
depth 60 cm) but you must ensure that it is properly ventilated.
Installation requires a compartment as illustrated and described in next chapters:
• Installation "A" between Existing Side Cabinets (560 or 600 mm GAP) (figs. 28, 29, 30, 31)
• Installation "B" between Side Cabinets by Removing Provious Housing (figs. 31, 32)
• Installation "C" by Using Housing Unit (figs. 33, 34, 35)
CAUTION: Do not lift the double oven by the door handles.
WARNING !
– We would point out that the adhesive which bonds the plastic laminate to the furniture must withstand
temperatures not less than 150° C to avoid delamination.
– The appliance must be housed in heat resistant units.
– The walls of the units must be capable of resisting temperatures of 75° C above room temperature.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Installation "A" between Existing Side Cabinets (560 or 600 mm GAP)
(figs. 28, 29, 30, 31)
– Mount the 2 (two) metal supports “B” (supplied with the
Installation “A”
560 mm Gap
appliance in a separate kit) as indicated in Figs. 29 or 32).
– Fig. 32 only - prepare 2 wood uprights “A” (width 20-50
mm, thickness 18 mm, length 650 mm); mount the 2 wood
uprights “A” to the cabinet walls as indicated in figure.
– Build in the double oven making it slide on the metal
supports “B”.
Installation "B" between Side Cabinets by
Removing Provious Housing (figs. 31, 32)
– Remove previous housing.
– Mount the 2 (two) metal supports “B” (supplied with the
appliance in a separate kit) as indicated in Fig. 32.
– Prepare 2 wood uprights “A” (width 20-50 mm, thickness 18
mm, length 650 mm); mount the 2 wood uprights “A” to the
cabinet walls as indicated in figure.
– Build in the double oven making it slide on the metal
supports “B”.
Fig. 28
560 mm Gap
(*) Measure calculated from the
underneath of the worktop to the top
support base of the “B” supports.
WARNING !
VERY IMPORTANT
The underside of the
cabinet shall be
opened to allow
correct air circulation.
B
595
Support base
B
Fig. 29
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Installation “B”
Installation “A”
600 mm Gap
Pre existing
600 mm cabinetry
Fig. 30
Fig. 31
600 mm Gap
(*) Measure calculated from the
underneath of the worktop to the top
support base of the “B” supports.
A
WARNING !
VERY IMPORTANT
The underside of the
cabinet shall be
opened to allow
correct air circulation.
B
A
595
Support
base
B
Fig. 32
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Installation "C" By Using Housing Unit
(figs. 33, 34, 35)
• Remove the single oven shelf, if fitted, as indicated in figure 33.
• Remove the upper cross member support as indicated in figure 34.
• Cut the bottom of the housing as indicated in figure 34.
• Screw oven base housing to adjoining cabinetry by suitable screws (not supplied) as indicated in
figure 35.
• Check the position of the cabinet legs to ensure the cut-out does not interfere with the legs support.
Otherwise the cabinet may have to be removed as in INSTALLATION TYPE "B".
• Mount the 2 (two) metal supports “B” (supplied with the appliance in a separate kit) as indicated in
Figs. 35).
• Build in the double oven making it slide on the metal supports “B”.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Installation “C”
Measure calculated from the underneath
of the worktop to the top support base
of the “B” supports.
B
Cabinet for installing
the oven
Support
base
Remove single oven
shelf, if fitted.
B
Fig. 33
30
15 15
36
18 18
Fig. 34
25
30
B
595
Fig. 35
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Fixing the Double Oven
The double oven should then be secured by 6 screws (not supplied) fitted into the holes provided at the
sides of the oven (Fig. 36). If you open the oven doors, you will see some screw holes.
Remember the housing should not be free standing but be secured to the wall and/or adjacent fittings.
Note: It is essential that when installing your double oven, adequate air circulation is available within the
installation. Inadequate air circulation may greatly impair the performance of your double oven and may
affect adjacent cabinets due to an increase in temperature.
Adjust the hinges of furniture door
adjacent to the double oven to allow
a 5 - 7 mm gap between the furniture
door and the oven frame.
IMPORTANT:
If installing a base panel leave a
space as indicated in fig. 37 to
allow air circulation.
Fig. 36
Fig. 37
KEEP ATTENTION !
STAND AWAY FROM LOUVERS POSITIONED
BELOW THE CONTROL PANEL.
HOT AIR WHICH ESCAPES CAN CAUSE BURNS
TO HANDS, FACE, END/OR EYES.
KEEP CHILDREN AWAY.
Fig. 38
Download from Www.Somanuals.com. All Manuals Search And Download.
41
IMPORTANT:
– To avoid damage to the lower trim please note the following instructions.
– The lower trim is designed to allow for good air circulation and the correct opening of the oven door.
– To ensure the trim is not damaged due to the appliance being placed on the floor, the appliance should
be suitably supported as in below illustrations.
– After installation the appliance door should be slowly opened to ensure no damage has occurred.
– No responsibility for lower trim damage will be accepted if these instructions have not been
followed.
OvenDoor
LLowerTrim
Air Flow
Fig. 39
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Electrical Installation
For your safety please read the following information:
WARNING! Before effecting any intervention on the electrical parts the appliance must be
disconnected from the network.
IMPORTANT: The oven must be installed in accordance with the manufacturer’s instructions.
Incorrect installation, for which the manufacturer accepts no responsibility, may cause
damage to persons, animals and things.
General
– The connection to the electrical network must be carried out by qualified personnel and must be
according to existing norms.
– The appliance must be connected to the electrical network verifying above all that the voltage
corresponds to the value indicated on the specifications plate and that the cables section of the electrical
plant can bear the load which is also indicated on the plate.
– The appliance can be connected directly to the mains placing an omnipolar switch with minimum
opening between the contacts of 3 mm between the appliance and the mains.
– The power supply cable must not touch the hot parts and must be positioned so that it does not exceed
75°C at any point.
– Once the appliance has been installed, the switch must always be accessible.
– If the power supply cable is damaged it must be substituted by a suitable cable.
IMPORTANT: this double oven must be connected to a suitable double pole control unit
adjacent to the oven.
NO DIVERSITY CAN BE APPLIED TO THIS CONTROL UNIT.
Feeder Cable Section
The connection of
Type H05RR-F or H05VV-F
the appliance to the
grounding unit is
mandatory.
230 V~
3 x 2.5 mm2 (**)
(**) – Connection to wall-mounting distribution panel.
The manufacturer
declines every
responsability for
any inconvenience
resulting from the
inobservance of this
condition.
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Connection the Double Oven Mains Cable
Important!
This oven must be connected to the mains power supply only by a suitably qualified person.
Unscrew the screws A securing the cover plate B behind the oven (fig. 40).
– Remove the cover plate B.
– Remove the screws C from the cable clamp (fig. 41).
– Insert the mains cable (type H05RR-F or H05VV-F - 3x2,5 mm2 section) into the cable protector P.
– Connect the phase and earth cables to the mains terminal connection block D.
EARTH
N
L
NEUTRAL
LIVE
– Refit the cable clamp so that it clamps the outer sleeving of the cable, and screw the screws C.
– Refit the cover plate B and fix it with the screws A.
WARNING: This appliance must be earthed
D
A
A
Green
&
Yellow
(Earth)
Brown (Live)
Blue (Neutral)
B
B
P
C
Fig. 40
Fig. 41
Download from Www.Somanuals.com. All Manuals Search And Download.
44
Appliance Servicing
CDA provide a quality and effective after-sales service to cover all your servicing needs.
Please attach your receipt to this page for safekeeping.
Please help us to help you by having the following information available when booking a service-call:
1. Model type, make and model – see the product data plate.
2. Evidence of installation / purchase date
3. Retailer where appliance was purchased
4. Clear and concise details of the fault
5. Full address including postcode and any contact phone numbers
Contact telephone numbers
CDA Customer Care Department
– Telephone: 01949 862012
– Fax: 01949 862003
– Email: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Guarantee
CDA appliances carry a five-year parts and a one-year labour guarantee.
CDA will repair or replace any defect or part attributable to faulty material or workmanship. Within the
first year this will be free of both labour and parts charges. After the first year and within five years, the
parts will be supplied free of charge provided that the repair is carried out by an agent authorised by CDA
and the labour will be charged at the commercial rate applicable at the time of repair.
The appliance must have been installed by a suitably qualified person and in accordance with the
manufacturer’s instructions and current legislation. The guarantee does not cover faults caused by the
incorrect fitting of appliances.
Limit of Cover
– The guarantee does not cover cosmetic damage e.g. discolouration or oxidisation.
– Proof of purchase or installation date must be produced before a service-call will be booked.
– The appliance must be used for domestic purposes only. Appliances used for commercial or professional
purposes are not covered by the guarantee. Commercial warranty is available at extra cost.
– The appliance must not be modified or tampered with or repair attempted by any unauthorised
person.
– The guarantee does not cover damage caused in transit or by misuse, accident, abuse or neglect.
– The guarantee does not cover routine maintenance.
– Use of parts not supplied or recommended by |C|D|A| will invalidate the warranty.
– Rubber seals, filters, removable glass parts, control knobs and buttons, fuses and light bulbs will need
replacing periodically and are not covered by the guarantee.
– Second-hand or reconditioned appliances are not covered by the guarantee.
The conditions under which this guarantee is offered are in addition to the statutory rights of the domestic
purchaser and these statutory rights are not affected by this guarantee.
CDA reserve the right to change specification without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Cod. 1103554 - ß2
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Download from Www.Somanuals.com. All Manuals Search And Download.
|