Installation
Instructions
WF2605, WF2608 Terrazzo
WF2705, WF2708 Stainless Steel
Classic Circular 36"/54"
Washfountain with Foot
Control
WF2605
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . . . . 2
Circular Washfountain Dimensions . . . . . . . . . . 3-4
Rough-In Specifications . . . . . . . . . . . . . . . . . . . 5-6
Drain Rough-In Specifications . . . . . . . . . . . . . . . .7
Pedestal Mounting and Assembly . . . . . . . . . . . . .8
Bowl and Pedestal Assembly and Mounting . . . . .9
Drain Spud Installation . . . . . . . . . . . . . . . . . . . . .10
Supplies w/Optional Soap Dispenser (A/O drains) . .11-12
Supplies w/Optional Soap Dispenser (B/H drains) . .13-14
Installing the Valve Assembly . . . . . . . . . . . . . . .15
Installing the Operating Rod . . . . . . . . . . . . . . . .16
Soap Valve Maintenance and Repair Parts . . .17-18
Check Valve Troubleshooting . . . . . . . . . . . . . . .17
Stop, Strainer and Check Valve Repair Parts . . . .19
Sprayhead Troubleshooting/Repair Parts . . . . . . 20
Foot Valve Breakdown and Repair Kit . . . . . . . .21
Manual Mixing Valve Repair Parts . . . . . . . . . . .22
Volume Control Valve Repair Parts . . . . . . . . . . .23
Vernatherm™ Mixing Valve Maintenance . . .24-26
Cleaning and Maintenance Instructions . . . . .27-28
WF2708
IMPORTANT
U
P
Read this entire installation manual
to ensure proper installation.
C
UPC Certified
C
R
Flush all the water supply lines
before making connections.
Main water supply to the unit
should be ON at all times.
This installation manual and parts
list should be filed by the owner’s
maintenance department.
P.O. Box 309, Menomonee Falls, WI 53052-0309
TEL. 1-800-BRADLEY FAX 262-251-5817
215-603 Rev. M; EN 06-915B
© 2007 Bradley Corporation
Page 1 of 28 4/6/2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Circular Washfountain Dimensions
E
H
D
C
B
A
F
G
Approximate Dimensions in Inches*
Material
Size
54
A
19
19
19
19
B
29-1/4
28
C
D
E
F
G
36
36
25
25
H
54
54
36
36
Terrazzo
39-1/8
37-3/8
35-5/8
33-7/8
47-5/8
45-7/8
44-1/8
42-3/8
56
32
Stainless Steel
Terrazzo
54
54-1/4
52-1/2
50-3/4
32
21
21
36
29-1/4
28
Stainless Steel
36
* Juvenile height (Terrazzo only): Subtract 4" from dimensions A through E for juvenile height.
Approximate Dimensions in Millimeters*
Material
Size
A
B
743
711
743
711
C
994
949
905
860
D
E
1422
1378
1334
1289
F
813
813
533
533
G
914
914
635
635
H
Terrazzo
1372
483
483
483
483
1210
1165
1121
1076
1372
1372
914
Stainless Steel 1372
Terrazzo
914
914
Stainless Steel
914
* Juvenile height (Terrazzo only): Subtract 4" from dimensions A through E for juvenile height.
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Length of Tie Pipe Required for Vent Through Washfountain Column
Type
Pipe Length
54" Less Soap Dispenser
21-1/2" (546mm)
18" (457mm)
36" Less Soap Dispenser
54" With Soap Dispenser
30" (762mm)
36" With Soap Dispenser
26-1/2" (673mm)
55-1/2" (1410mm)
52" (1321mm)
48" (1219mm)
44-1/2" (1130mm)
32" (813mm)
54" Less Soap Dispenser With Towel Dispenser
36" Less Soap Dispenser With Towel Dispenser
54" With Soap Dispenser With Towel Dispenser
36" With Soap Dispenser With Towel Dispenser
54" With Cube Adapter
36" With Cube Adapter
28-1/2" (724mm)
50" (1270mm)
46-1/2" (1181mm)
40" (1016mm)
36-1/2" (927mm)
54" With Cube Adapter With Towel Dispenser
36" With Cube Adapter With Towel Dispenser
54" With Cube Adapter And Soap Dispenser
36" With Cube Adapter And Soap Dispenser
NOTE: Drain must be connected with 2" schedule 40 welded wrought iron pipe, minimum, to provide
lower support for this installation. Vent or support pipe must be of the same material in 1-1/2".
4
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Rough-In Specifications
Type A
Off-line vent with
supplies from below
TOP VIEW
1" NPT supplies through
floor: stub up 2-1/2" (64)
above floor
7-5/8" 7-5/8"
(194) (194)
2-1/2"
(64)
NOTE: UPC and IPC restrict the vertical
distance from the fixture outlet to the trap
weir to not more than 24". Check state and
local codes for variances.
Hot
Cold
2" NPT drain:
4"
stub up 3" (76)
above floor
(102)
36" (914) bowl
54" (1372) bowl
TOP VIEW
1" NPT supplies from above
must reduce to 1/2 nom. copper
tube on these centers to
Type B
Centrally rising vent with
supplies from above
pass thru washfountain
7/8"
(22.2)
7/8"
(22.2)
Hot
1-1/4"
(32)
Cold
2" NPT drain:
stub up 3" (76)
above floor
1-1/2" NPT vent to ceiling
4"
(102)
36" (914) bowl
54" (1372) bowl
Rough-In Notes:
1. All pipes and fittings not furnished by Bradley are shown in broken lines.
2. Supply lines for one to two washfountains should be 1"; for three washfountains 1-1/4"; for more
than three washfountains, pipe sizes should be increased proportionately.
3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.
4. Check valve inlets are 1/2" NPT.
5. Dimensions shown in parentheses are millimeters.
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Rough-In Specifications ... Continued
Type O
Off-line vent with
supplies from above
TOP VIEW
1" NPT supplies from above
must reduce to 1/2 nom. copper
tube on these centers to
NOTE: UPC and IPC restrict the vertical
pass thru washfountain
distance from the fixture outlet to the trap
weir to not more than 24". Check state and
local codes for variances.
7/8"
7/8"
(22.2)
(22.2)
Hot
Cold
1-1/4"
(32)
2" NPT drain:
stub up 3" (76)
above floor
4"
(102)
TOP VIEW
36" (914) bowl
1" NPT supplies through
floor: stub up 2-1/2" (64)
above floor
54" (1372) bowl
7-5/8" 7-5/8"
(194) (194)
2-1/2"
(64)
2" NPT drain:
stub up 3" (76)
above floor
Hot
Cold
Type H
Centrally rising vent with
supplies from below
4"
(102)
1-1/2" NPT
vent to
ceiling
36" (914) bowl
54" (1372) bowl
Rough-In Notes:
1. All pipes and fittings not furnished by Bradley are shown in broken lines.
2. Supply lines for one to two washfountains should be 1"; for three washfountains 1-1/4"; for more
than three washfountains, pipe sizes should be increased proportionately.
3. Overhead supplies must be reduced to 1/2" copper tube to pass through support tube.
4. Check valve inlets are 1/2" NPT.
5. Dimensions shown in parentheses are millimeters.
6
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Step 1: Rough-In of Drain & Supplies
1. Rough in supply and drain piping as required for your installation (see pages 5-6 for rough-ins of
the optional installations).
2. Assemble the drain to the dimension shown in Figure 1 and Table 1 for bowl size of the
Washfountain you are installing.
NOTE: All piping shown in dotted lines to be supplied by the installer. Compliance and conformity to
local codes and ordinances is the responsibility of the installer.
Types B, H
Vent
or
Vented Trap
(111-024)
Tie Pipe
2" NPT Coupling if Tie
Pipe is not required
(Supplied by Installer)
(Supplied by Installer)
Centerline of
W
a
shfountain
able 1
T
B – See
4"
Centerline of
able 1
T
W
B – See
ashfountain
(102)
Vent
or
4"
(102)
Optional
Tie Pipe Bracket
(S70-082)
Tie Pipe
(Supplied by Installer)
Centerline of
W
Types A, O
ashfountain
able 1
T
B – See
4"
(102)
See rough-ins
on Pages 5-6
for dimensions
not shown
Types A, O
With Tie Pipe
Bracket Option
Figure 1
Table 1 — “B” Trap Dimensions
Material
Terrazzo
Size
54"
54"
36"
36"
Dim
B
Standard Height
18-5/8" (473mm)
17" (432mm)
Juvenile Height
14-5/8" (371mm)
N/A
Stainless Steel
Terrazzo
B
B
18-5/8" (473mm)
17-3/8" (441mm)
14-5/8" (371mm)
N/A
Stainless Steel
B
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Installation Instructions continued . . .
Step 2: Assembling the Pedestal
1. Assemble the leg and scuff base panels with the 5/16” carriage bolts and nuts provided (Figure 2).
2. Attach the pedestal frame members with the 5/16” stove bolts and nuts provided (Figures 2 and 3).
3. Add the foot levers and operating cross to the pedestal assembly (Figures 2 and 4).
4. Press the foot rail into place with a rolling motion. The joint of the foot rail should be placed in
the clevis of one of the foot valves (Figure 2).
Figure 2
Figure 3
Figure 4
8
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions continued . . .
Step 3: Bowl and pedestal assembly and mounting
IMPORTANT: FOR PROPER DRAINAGE, THE BOWL AND PEDESTAL MUST BE
LEVEL WHEN THEY ARE SECURED TO THE FLOOR .
WARNING: USE SUITABLE LIFTING EQUIPMENT TO POSITION THE BOWL AND
PEDESTAL ASSEMBLY. HANDLE WITH CARE! FAILURE TO DO SO
COULD RESULT IN SERIOUS PERSONAL INJURIES.
STAINLESS STEEL BOWL:
1. Place the bowl on the pedestal using
suitable lifting equipment.
2. Fasten the bowl to the pedestal with the
four flat head stove bolts provided. Place
the bowl clip inside the pedestal leg (see
Figure 5).
3. Position the bowl and pedestal assembly
so that the bowl drain is in line with the
trap or drain line (see Figure 6 at right and
Figure 5
figure 7 on page 10).
4. Screw the drain spud part of the way into
the drain to ensure correct alignment (see
Figure 7 on page 10).
TOP VIEW OF PEDESTAL ASSEMBLY
5. Anchor the pedestal assembly to the floor
and wall with suitable anchors/fasteners
(supplied by installer).
TERRAZZO BOWL:
CAUTION: Bowl Surface is smooth.
Use suitable lifting
equipment to position
the bowl and pedestal
assembly. Handle with
CARE!
Figure 6
1. Place the pedestal assembly as shown in Figure 6.
2. Place the bowl on the pedestal using suitable lifting equipment.
3. Screw the drain spud part way into the drain to ensure correct alignment (see Figure 7).
4. Anchor the pedestal assembly to the floor with suitable anchors/fasteners (supplied by installer).
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Installation Instructions continued . . .
Step 4: Installing drain spud in bowl
NOTE: Seal between drain spud and drain hole with plumber’s putty (supplied by installer).
1. Secure drain spud with lock nut and washers as shown in Figure 7.
STRAINER
(S45-067)
SPUD
112-015 (Terrazzo)
112-016 (Stainless Steel)
BOWL
WASHER
(142-068)
Figure 7
LOCKNUT
(161-021)
10
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions continued . . .
Step 5a: Installing Supplies with Optional Soap Dispenser for A/O drain units
NOTE: See Step 5b for units with type B/H drain.
NOTE: For models with optional paper towel dispensers, tie pipe assembly, or shroud, see separate
instruction sheets and Step 5b for units with type B/H drain.
NOTE: Flush the supply lines before making connections.
1. Install the hemmed end (not sharp end) of the support tube with the gasket into the bowl.
2. Using pipe sealant, connect the supply pipe to the sprayhead and place on top of the support tube as
shown in Figure 8 on page 12.
3a. For Unit with Soap Option:
1. Place the upper tie bar on top of the sprayhead and join the upper and lower tie rod (the longer threaded
rod) with the coupling nut and setscrews.
2. Insert the tie rod assembly through the hole in the upper tie bar and secure with the lower tie bar, tie rod
nut and setscrew from below (see Figure 8).
3. Install the spacer, soap dispenser, dispenser cover and secure with the acorn nut and socket setscrew.
4. Continue installation with Step 7 on Page 16.
3b. For Unit without Soap Option:
1. Place the dispenser cover on the sprayhead. Thread the acorn nut onto the lower tie rod, run the tie rod
through the dispenser cover and secure from below with the lower tie bar, tie rod nut and socket setscrew
(see Figure 8).
2. Continue installation with Step 6 on Page 15.
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
TYPE "O" DRAIN
(Supplies from above)
TYPE "A" DRAIN
Acorn Nut (110-052A)
& Set Screw (160-093)
Dispenser Cover
Soap
Dispenser Lid
Upper Tie Rod
(176-010)
Spacer
(113-155A)
PARTS SHOWN IN
BOX ARE FOR
UNITS WITH SOAP
DISPENSER.
Soap
Dispenser
Upper Tie Bar
(159-009A)
(notched at corners)
Coupling Nut (110-051D)
Set Screws (160-208)
Sprayhead
(S05-054)
Support Tube
(S57-005, 54")
(S57-006, 36")
Lower Tie Rod
(176-008, 36")
(176-008A, 54")
Sprayhead Supply
Pipe (3/8")
Gasket
(125-011, Terrazzo)
(125-008, Stainless Steel)
Lower Tie Bar
(159-009)
Tie Rod Nut
(110-064)
& Set Screws
(160-208)
(See Figure 10 on page 15
for valving assembly)
Operating Rod
(S14-007, Std. Ht.)
(S14-007A, Juv. Ht.)
HOT
COLD
Figure 8
12
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions continued . . .
Step 5b: Installing Supplies with Optional Soap Dispenser for B/H drain units
NOTE: Flush supply lines before making connections.
1. Install the hemmed end (not sharp end) of the support tube with gasket onto the bowl.
2. Using pipe sealant, connect the supply pipe to the sprayhead and place on top of the support tube
as shown in Figure 9 on page 14.
3. Insert the 1-1/2" vent pipe (supplied by installer, see page 4 for length) through the soap dispenser
with the spacer (if provided), sprayhead and support tube.
4. Connect to the vented trap (provided).
5a.For Unit with Soap Option:
1. Slide the tie bar over the 1-1/2" vent pipe 1/2" below the top of the soap dispenser and secure
with the set screws.
2. Slide the dispenser cover over the 1-1/2" vent pipe and secure with the two screws (included)
to the tie bar.
5b.For Unit without Soap Option:
1. Slide the tie bar over the 1-1/2" vent pipe, 1/2" below the top of the sprayhead and secure with
the set screws.
2. Secure the dispenser cover over the 1-1/2" vent pipe and secure with the two screws included
with the tie bar.
6.Connect the Vent Pipe
a. Connect the vent pipe to the vent through the ceiling with the pipe union.
b. Continue installation with Step 6 on Page 15.
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Installation Instructions continued . . .
TYPE "H" DRAIN
(Supplies from below)
TYPE "B" DRAIN
HOT
COLD
Cap Screw
(160-108)
Supplies 1/2" Nom.
Copper Tubing
1-1/2" Vent Pipe
Tie Bar Location
For Unit With Soap
(159-020)
Soap Dispenser Lid
PARTS SHOWN IN
BOX ARE FOR
UNITS WITH SOAP
DISPENSER.
Spacer
(113-155A)
Soap
Dispenser
Tie Bar Loation For
Unit Without Soap (159-020)
Support Tube
(S57-005, 54")
(S57-006, 36")
Sprayhead
(S05-054)
Sprayhead Supply
Pipe (3/8")
Gasket
(125-011, Terrazzo)
(125-008, Stainless Steel)
Vented Trap
(111-024)
(See Figure 10 on page 15
for valving assembly)
Operating Rod
(S14-007, Std. Ht.)
(S14-007A, Juv. Ht.)
Figure 9
14
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions continued . . .
Step 6: Installing the Valve Assembly
NOTE: Flush supply lines before making connections.
1. Connect the stop-strainer-check valves, mixing valve, volume control valve, and foot valve as
shown in Figure 10.
2. For overhead supply lines, install 1/2"nominal copper supply tubing by passing the lines through
the holes in the dispenser cover and then down through the support tube.
3. Install the valving assembly using suitable fittings to the supplies as shown in Figure 10 at the
approximate height indicated in Table 2.
4. Slide the tailpiece nut over the tailpiece and connect the tailpiece to the supply pipe (or to the
nipple/coupling for B or H drain).
To Supply Pipe
Coupling
(169-174)
Used on "B"
Nipple
and "H" models only
Tailpiece
(129-009)
STD: 2" Long (113-852)
JUV: Close (113-006AL)
Nut
(110-005)
Tailpiece Washer
(124-001AF)
Stop-Strainer-Check
Valve
(S60-003)
Foot Valve
(S07-066)
Operating Lever
Nut
(110-005)
Washer
(124-001AF)
Tailpiece
(129-007)
Manual Mixing
Valve
(S01-038)
Distance (dimension)
finished floor - see
Table 2
OPTIONAL Vernatherm™
Thermostatic
Mixing Valve
(S01-525)
(Units are supplied with
Manual Mixing Valve as
standard equipment)
Valve Assembly
Figure 10
Table 2 — Distance to Finished Floor
Model Number
Standard Height
Juvenile Height
Type A
Type B
Type H
Type O
9" (229mm)
5-1/4" (133mm)
6-3/16" (157mm)
3-7/16" (87mm)
6-3/16" (157mm)
3-7/16" (87mm)
9" (229mm)
5-1/4" (133mm)
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Installation Instructions continued . . .
Step 7: Installing the Operating Rod
1. Insert the operating rod in the operating rod lever and then into the foot lever (see Figure 11).
NOTE: For normal operation, use the operating rod as shipped. The spring loaded cartridge should
be adjusted so there is no play in the operating lever. Care must be taken to insure that a snug fit is
achieved without activating the foot valve or water will leak from the sprayhead (see Figure 11).
2. When movement of the operating rod is insufficient to open the foot valve, disassemble the rod
and remove the spacer and override spring. Reassemble the operating rod as shown in Figure 12.
Reinstall and adjust so that the foot valve is completely open when the foot lever is fully
depressed. This prevents damage to the foot valve due to the absence of the override spring.
3. Turn supplies on and activate the sprayhead. Check piping installation for leaks.
4. Clean the sprayhead if necessary. See page 22 for sprayhead troubleshooting. Adjust the volume
control valve, if necessary, to control the flow of water.
Figure 12
Figure 11
16
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Soap Recommendations and Maintenance Tips
Quality soap dispensers require good quality soap and periodic maintenance to properly operate. Bradley
soap dispensers will provide dependable, consistent operation over the long term when soap with
reasonable viscosity and pH levels are used and when a minimal amount of periodic maintenance is
performed on the valves.
Soap thickness is determined by a measurement called viscosity. Soap viscosity should be between 100 cps
(centerpoise) and 2500 cps for all Bradley soap dispensers. Thinner soaps are perceived by the users as
being “watered down” so users tend to take more than they need, resulting in waste. Thick soaps flow
slower and inhibit the “flushing” action of the valves, which allows the soap to congeal in the valve and
cause clogs.
The pH (acid) level of the soap should be in the range of 6.5 to 8.5. More acidic soaps (pH levels lower
than 6.5) will corrode metal parts (even stainless steel!!) and degrade rubber and plastic components. They
will also cause skin irritation. Most inexpensive soaps (typically the pink lotion type) fall into this acidic
category and will eventually cause valve failure and metal corrosion. Base soaps (pH levels higher than
8.5) will cause swelling or degradation of rubber and plastic parts and skin irritation.
Generally, any quality soap meeting the viscosity and pH guidelines above will work well with Bradley
soap dispensers. PCMX or Isapropanol based antibacterial soaps (within viscosity and pH limits) will also
work with Bradley dispensers. Soaps satisfying these basic guidelines will provide consistent flow and
reduce clogs.
Most soap dispenser problems are caused by soap that is too thick or corrosive, or by a lack of maintenance.
Many soaps come in concentrate form which must be diluted with water. Often, the soap is improperly
diluted or used straight out of the bottle, which causes clogging and valve failure. If proper soap is being
used, valves that have never been cleaned are usually the source of dispensing problems. Bradley has
entered into an agreement with Champion Brand Products to provide additional customer service for
purchasers of our dispensers regarding soap issues. They are very helpful and can get to the bottom of
almost any soap dispenser-related problem. They also sell an excellent “Bradley approved” soap. Please
see Bradley Instruction sheet 215-1286 for soap valve cleaning details and Champion Brand Products
contact information.
Check Valve Troubleshooting
If water just dribbles or does not flow from sprayhead:
1. Turn off water supplies to fixture.
2 Inspect check valves for proper installation. See Stop, Strainer and Check Valve on page 19.
3. Open the stops and clean the strainers, if necessary.
If water sprayhead delivers all hot or cold water:
1. Turn off water supplies to fixture.
2. Inspect check valves for proper installation.
3. Open the stops and clean the strainers, if necessary.
4. Inspect mixing valve for proper installation (see Vernatherm valve on page 24).
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
* Not Illustrated
Parts List
Soap Valve - Liquid - S09-007S
Attaching
Parts
S09-007S
This valve delivers a measured
amount of soap with each
upward stroke. The soap
dispenser has been standard on
washfountains since 1983 and
is not well-suited for very thick
lotion soaps.
Item
Part No.
Description
Qty
1
2
3
4
5
*
118-025
110-007
135-001L
Valve Body
Packing Nut
Spring
1
1
1
1
1
1
2
1
125-001BU Washer
NOTE: Lotion soap will clog
liquid soap valves. Use only
lotion soap valves with lotion
soap.
119-028
161-014
124-001D
Plunger
Nut
*
Washer
*
142-002AH Washer - Stainless Steel
Parts List
Soap Valve - Lotion - S09-057S
Valve
Assembly
Attaching
Parts
S09-057 S09-057S
Item
Part No.
Description
Qty
1
2
3
4
5
6
7
8
124-001D
110-057
Washer
Nut
—
—
—
—
—
—
1
1
1
1
1
1
1
1
1
125-001AN
159-114
Stopper
Reinforcing Plate
Washer
Screw
124-001AT
160-176
S09-040
S53-045
Valve
Adaptor
1
Soap Valve - Powdered - S09-010A
Parts List
Item Part No.
Qty
Description
1
2
3
4
160-069
142-002X
S62-002
192-004
1
1
1
1
Screw, 1/4-20 RD
Washer, 1/4 Split-Lock
Agitator / Slide Assy.
Lever - Powdered Soap
NOTE: Reducer plugs are available for use with fine granulated soap to
reduce the flow.
NOTE: Valves can be changed from powdered to liquid by plugging the
innermost, or “bearing” hole with rubber plug, part number 125-001AK.
To change from liquid to powdered, the plug must be removed. If none is
present, it will be necessary to drill out the bearing hole with a 1/2" or
5/8" drill. The plastic container configuration forms a natural template
for locating the bearing hole.
18
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Stop, Strainer and Check Valve
1
2
3
Stop
3
5
4
2
6
4
Strainer
1
8
Parts List
Stop Assembly S21-014
Standard Celcon Core
1/2" NPT
1/2" NPT
Item Part No.
Qty
Description
1
*2
*3
4
119-057
1
1
1
1
Valve Core
“O” Ring
9
125-001AW
125-001L
160-164
11
5
7
10
Bibb Washer
Screw
6
Check
Parts List
S60-003 Stop, Strainer and Check Valve
1
2
Item Part No.
Qty
Description
1
1
118-039
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
Valve Body - Brass
Valve Body - Plated
Set Screw
118-039A
160-131
2
Parts List
Check Assembly S21-015*
3
S21-014
S21-026
156-006
Stop Assembly - Celcon
Stop Assembly - Brass
Strainer
3
Item Part No.
Qty
Description
*4
*5
*6
7
1
2
119-091
1
1
Plunger
Washer
124-001BV
153-068
Fiber Washer
125-001BB
Plug - Brass
129-007
Tail Piece - Brass
Tail Piece - Plated
Tail Piece Nut - Brass
Tail Piece Nut - Plated
Tail Piece Washer
Spring
7
129-007A
110-005
8
8
110-005A
124-001AF
135-001AB
S21-015
*9
*10
*11
Check Assembly
*
S45-050 Repair Kit Includes these parts
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Sprayhead Troubleshooting and Repair Parts
Problem: Water splashes over the rim of the bowl.
Cause: Foreign matter has reduced the size of the sprayhead slots, causing greater pressure at the
open slots.
Solution: Clean the sprayhead:
1. Disassemble the sprayhead and dislodge any dirt, lime build-up and foreign debris with a wire
brush.
2. Sprayheads with rubber grommet spray rings may be cleaned by rubbing a coin over the grommet.
3. Throttle down the volume control (water spray should strike the bowl without splashing outside
of the bowl).
Problem: Water flow diminishes from the sprayhead.
Cause: Strainer portion of the stop-strainer-check valve is plugged.
Solution: Remove and clean the strainer screen from the stop-strainer-check valve.
NOTE: The sprayhead shown below includes a perforated rubber spray ring grommet that is self-
cleaning. The water pressure flexes the spray holes which slows accumulation of foreign matter and
tends to “break loose” any such deposits that may have accumulated.
Parts List
Sprayhead Assembly
S05-054
Repair Kit
S45-051
Item
Part No.
Description
Qty
1
2
125-001DE
139-031
Neoprene Washer-Top
Sprayhead Manifold
Washer
1
1
3
3
1
1
3
3
1
1
1
—
4
3
124-001AL
160-211
4
Carriage Bolt
4
5
115-061
Sprayhead Top
Sprayhead Bottom
Washer
—
—
4
6
116-008
7
124-001AT
161-025
8
Nut
4
9
124-020C
125-001DF
Sprayhead Grommet - Circle
Neoprene Washer-Bottom
—
1
10
20
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Repair Parts continued . . .
S65-230 — Repair Kit for Foot Valve S07-066
S07-066 Foot Valve
6
7
ITEM QTY. PART NO.
DESCRIPTION
5
4
8
1
2
1
1
1
1
1
1
1
1
1
1
1
1
118-302
125-154
118-300
135-088
117-016
S64-093
125-001Y
179-002
119-024
143-026
110-101
124-001V
FOOT VALVE BODY
O-RING, #2-127
HOUSING
9
10
3
4
SPRING
5
VALVE SEAT
6
PLUNGER ASSEMBLY
DIAPHRAGM
7
3
8
PLUNGER GUIDE
PLUNGER
11
2
12
9
1
10
11
12
OPERATING LEVER
BOTTOM NUT
WASHER, 1-3/8" x 5/8"
NOTE: This repair kit services only the S07-066 valve shipped AFTER January 2003.
See 215-1370 Washfountain Parts and Service Guide for service information before this date.
S65-230 Foot Valve Repair Kit
ITEM QTY. PART NO.
DESCRIPTION
8
1
2
3
4
5
6
7
8
9
1
1
1
1
1
1
1
1
1
118-300
135-088
125-154
S64-093
117-016
125-001Y
124-001V
130-033
S45-125
HOUSING
6
SPRING
O-RING, #2-127
PLUNGER ASSEMBLY
VALVE SEAT
DIAPHRAGM
WASHER, 1-3/8" x 5/8"
KEY, VALVE SEAT
LUBRICANT (not shown)
5
2
4
3
7
1
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Manual Mixing Valve Repair Parts
Manual Mixing Valve Parts List
Valve
Valve and
Assembly
S01-038
Tailpieces
S01-038S
Repair Kit
S45-197
Item
Part No.
118-034
Description
Qty
1
1
2
3
4
5
6
6
7
7
*
Mixing Valve Body - Brass
Mixing Valve Body - Chrome
Fiber Washer
1
—
1
1
—
1
—
—
1
118-034A
124-001BD
125-001BC
119-059
O-Ring
1
1
1
Mixing Valve Core
Roll Pin
1
1
1
152-038
1
1
1
121-016
Bonnet - Brass
1
1
1
121-016A
160-197
Bonnet - Chrome
Screw - Brass
—
1
—
1
—
—
—
—
—
—
—
2
160-189
Screw - Stainless Steel
Tailpiece - Brass
Tailpiece Nut - Brass
Tailpiece - Chrome
Tailpiece Nut - Chrome
Tailpiece Washer
—
—
—
—
—
—
—
2
129-007
*
110-005
2
*
129-007A
110-005A
124-001AF
—
—
2
*
*
*
Parts not shown
22
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Volume Control Valve Repair Parts
Volume Control Valve Parts List
Brass
Valve
S02-045
Repair Kit
S45-198
Qty
Item
Part No.
Description
1
2
3
3
4
5
6
6
125-001BC
O-Ring
Roll Pin
Bonnet
Bonnet
1
1
1
1
152-038
121-016
121-016A
124-001BD
119-060
1
1
—
1
—
1
Fiber Washer
Valve Core
Valve Body
Valve Body
1
1
118-033
1
—
—
118-033B
—
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Adjusting the Vernatherm Thermostatic Mixing Valve
NOTE: This valve is NOT factory preset. Upon installation, the temperature of this valve must be
checked and adjusted to ensure delivery of a safe water temperature. Water in excess of 110°F
(43°C) may cause scalding.
1. Check the temperature when approximately 1.0 GPM water flow is reached and adjust if
necessary (the range of the valve is 95°F–115°F (35°C–43°C). To adjust the temperature, follow
the procedure below:
• Loosen temperature locking nut with wrench.
• Using a blade screwdriver, turn the adjustment stem counterclockwise to increase the
temperature or clockwise to decrease the temperature (Figure 13).
• Once desired temperature has been reached, tighten lock nut to prevent change in temperature.
2. Shut the hot water inlet off by closing the hot water stop-strainer-check valve. While the hot
water supply is turned off, check to make sure the cold water flow is reduced. If the cold water
is reduced properly, reopen the hot water supply.
3. Shut the cold water inlet off by closing the cold water stop-strainer-check valve. While the cold
water supply is off, check to make sure that the hot water flow has shut down.
TEMPERATURE
TEMPERATURE
ADJUSTMENT
LOCKING
STEM
NUT
Figure 13
24
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Thermostatic Mixing Valve Maintenance and Troubleshooting
NOTE: Before attempting to troubleshoot the valve or disassemble the components, check for the
following conditions:
• If stop/check valves are used, make sure that they are fully open
• Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross-
connections or leaking stop/check valves
• check the hot water heater output to make sure that it is at least 20° F above the set temperature.
Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the
valves after inspection and repair is complete.
Problem: Limited water flow
Cause: Dirt and debris have built up in the valve.
Solution: Check the valve's piston for free and smooth movement, follow the procedures outlined
below:
1. Remove the valve's cap and thermostat (see Figure 14 on Page 26).
2. Push down on the piston with your finger (the piston should move freely). If the movement is
not as it should be, the piston needs to be cleaned. Follow the method outlined below for cleaning
the piston and valve body:
• Remove the thermostat.
• Lift the piston out with a needle-nose pliers and remove the spring.
• Any cleaner suitable for brass and stainless steel may be used (if cleaning with suitable cleaner
is not sufficient to remove debris, a 400-grit sandpaper may be used to polish and hone the
piston and valve body).
• Snap spring into piston (will detent) and reassemble into the valve body.
• Retest the piston.
3. If, after a thorough cleaning, the piston does not move freely, the piston must be replaced.
Contact your Bradley representative and ask for Repair Kit (part number S65-259).
Problem: External leaks in the system
Cause: O-rings have been damaged.
Solution: Replace O-rings where necessary. For replacement of the O-rings, contact your
Bradley representative and ask for Repair Kit (part number S65-259).
Problem: Improper water temperature or temperature fluctuation
Cause: Thermostat is slowly failing or not working at all.
Solution: "Check the thermostat for proper operation".
1. At room temperature (80° F or less) remove cap and thermostat.
2. Place thermostat into container with 115° F water. The pushrod should pop out of the
thermostat approximately 1/10".
3. If thermostat pushrod does not pop out, the thermostat must be replaced. Contact your Bradley
representative and ask for Repair Kit (part number S65-259).
Cause: Valve temperature is not properly set.
Solution: "Adjust the temperature" per steps on Page 24.
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Vernatherm Thermostatic Mixing Valve (S01-525) Parts List — Repair Kit S65-259
Parts List
S65-259
Valve Repair Kit
Description
10
9
Nut 3/8-24 Hex Jam
Cap
Item Part No.
Qty
5
7
8
S39-413
125-001BX
125-157
1
1
1
Thermostat
O-Ring
O-Ring
8
O-Ring
O-Ring
7
6
5
Stem
Thermostat
Piston
4
3
Spring
2
Seal Cup
1
Valve Body
Figure 14
26
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
Installation Instructions
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Cleaning of Washfountains
To Preserve Finish of Terrazzo Compositions
Clean terrazzo Washfountain bowls daily or as often as conditions require with any standard
household detergent, hot water and soft cloth. Bradley terrazzo bowls may be refurbished by
cleaning with tri-sodium phosphate, two pounds per gallon, and a scrub brush. Stubborn spots may
be removed with emery cloth. After bowl is thoroughly cleaned and dried, Epoxy resin or a good
quality polyurethane finish should be applied.
Eroded terrazzo is usually the result of exposure to caustic substances. This condition can be
repaired relatively easily. Repair kits are available from your Bradley Representative. Do not use
drain cleaners on terrazzo.
Drain Cleaning
Drains can be cleaned with a plumbers snake inserted through the drain spud after removing the
strainer, or through the trap clean out plug
IMPORTANT: Do not put drain cleaners in bowl. Damage to bowl will result.
Bradley Corporation • 215-603 Rev. M; EN 06-915B
4/6/2007
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Classic Circular 36"/54" Washfountain with Foot Control
WF2605, WF2608 Terrazzo — WF2705, WF2708 Stainless Steel
Installation Instructions
Cleaning and Maintenance Instructions for Stainless Steel
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive.
Proper care, particularly under corrosive conditions, is essential. Always start with the simplest solution and
work your way toward the more complicated.
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia.
Apply the cleaning solution per the manufactures instructions and always use a soft cloth or sponge to avoid
damaging the finish.
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball®
stainless steel cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same
direction as the polish lines.
IMPORTANT: NEVER USE ORDINARY STEEL WOOL OR STEEL BRUSHES ON STAINLESS
STEEL. ALWAYS USE STAINLESS STEEL WOOL OR STAINLESS STEEL BRUSHES.
Special Situations for Material
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and
polish in accordance with the manufactures instructions. Many of these products leave a protective coating
the helps prevent future smears and fingerprints.
Grease and Oil : To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in
accordance to the manufactures instructions and in the direction of the polish lines.
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents),
thiocyanates (pesticides, photography chemicals, and some foods), and iodides on stainless steel equipment,
especially if acid conditions exist.
IMPORTANT: DO NOT PERMIT SALTY SOLUTIONS TO EVAPORATE AND DRY ON
STAINLESS STEEL.
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the
actual source of the rust in some iron or steel particles which may be touching, but not actually a part of the
stainless steel structure.
NOTE: Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use of
these cleaners should be avoided.
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an
endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named are
regional in distribution, and can be found in local supermarkets, department and hardware stores, or through your
cleaning service. It is emphasized that all products should be used in strict accordance with package instructions.
28
4/6/2007
Bradley Corporation • 215-603 Rev. M; EN 06-915B
Download from Www.Somanuals.com. All Manuals Search And Download.
|