User’s Manual
Large Format Display
MultiSync C751Q
MultiSync C861Q
MultiSync C981Q
MODEL: C751Q, C861Q, C981Q
Please find your model name in the label on the rear side of monitor.
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address:
500 Park Boulevard, Suite 1100
Itasca, Illinois 60143
(630) 467-3000
Tel. No.:
Type of Product:
Equipment Classification:
Model:
Display Monitor
Class B Peripheral
MultiSync C751Q (C751Q)
MultiSync C861Q (C861Q)
MultiSync C981Q (C981Q)
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
FCC Information
1. Use the attached specified cables with this color monitor so as not to interfere with radio and television reception.
(1) Please use the supplied power cord or equivalent to ensure FCC compliance.
(2) Please use the supplied shielded video signal cable.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify and
Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C.,
20402, Stock No. 004-000-00345-4.
Windows is a registered trademark of Microsoft Corporation.
NEC is a registered trademark of NEC Corporation.
OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and
Switzerland.
DisplayPort and DisplayPort Compliance Logo are trademarks owned by Video Electronics Standards
Association in the United States and other countries.
All other brands and product names are trademarks or registered trademarks of their respective owners.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and
other countries and areas.
microSD and microSD SDHC logos are trademarks of SD-3C, LLC.
CRESTRON and CRESTRON ROOMVIEW are trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and other countries.
GPL/LGPL Software Licenses
The product includes software licensed under GNU General Public License (GPL), GNU Lesser General Public License (LGPL),
and others.
For more information on each software, see “readme.pdf” inside the “about GPL&LGPL” folder on the supplied CD-ROM.
Adobe and the Adobe logo are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or
other countries.
English-1
Important Information
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE
PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER
CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has
been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this monitor in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
This equipment is designed to be used in the condition of the power cord connected to earth. If the power cord is not connected
to the earth, it may cause electric shock. Please make sure the power cord is earthed properly.
European
Continental
Plug Type
North America
U.K.
Chinese
Japanese
Plug Shape
U.S.A./
Canada
Region
Voltage
EU (except U.K.)
230
U.K.
230
China
220
Japan
100
Taiwan
110
120*
* When operating this monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply
voltage of the AC power outlet being used.
NOTE:
This product can only be serviced in the country where it was purchased.
Use the power cord which has BSMI mark at both ends when you use this monitor in Taiwan.
•
•
The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment.
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.
English-2
Safety Precautions, Maintenance & Recommended Use
Safety Precautions and Maintenance
•
•
Do not use the monitor in high temperature, humid, dusty,
or oily areas.
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTI-FUNCTION MONITOR:
Do not use monitor under rapid temperature and humidity
change condition and avoid cold air from air-conditioning
outlet directly, as it may shorten the lifetime of the monitor
or cause condensation. If condensation of water has
happened, let the monitor stand unplugged until the
condensation has disappeared.
•
DO NOT OPEN THE MONITOR. There are no user
serviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other
risks. Refer all servicing to qualified service personnel.
Connecting to a TV*
•
•
Do not bend, crimp or otherwise damage the power cord.
•
Cable distribution system should be grounded (earthed)
in accordance with ANSI/NFPA 70, the National Electrical
Code (NEC), in particular Section 820.93, Grounding of
Outer Conductive Shield of a Coaxial Cable.
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
•
The power supply cord you use must have been
approved by and comply with the safety standards of your
country. (Type H05VV-F 3G 0.75 mm2 should be used in
Europe).
•
The screen of the coaxial cable is intended to be
connected to earth in the building installation.
Under the following conditions immediately disconnect your
monitor from the wall outlet and refer servicing to qualified
service personnel:
•
•
In UK, use a BS-approved power cord with molded
plug having a black (5 A) fuse installed for use with this
monitor.
•
•
When the power supply cord or plug is damaged.
The power cable connector is the primary means of
detaching the system from the power supply. The monitor
should be installed close to a power outlet, which is easily
accessible.
If liquid has been spilled, or objects have fallen into the
monitor.
•
•
If the monitor has been exposed to rain or water.
•
•
Do not spill any liquids into the cabinet or use your
monitor near water.
If the monitor has been dropped or the cabinet has been
damaged.
Do not insert objects of any kind into the cabinet slots,
as they may touch dangerous voltage points, which can
be harmful or fatal or may cause electric shock, fire or
equipment failure.
•
•
If you notice any structural damage such as cracks or
unnatural wobbling.
If the monitor does not operate normally by following
operating instructions.
•
•
•
Do not place this product on a sloping or unstable cart,
stand or table, as the monitor may fall, causing serious
damage to the monitor.
Recommended Use
•
•
•
•
For the monitor’s optimum performance, allow 20 minutes
for warming up.
Do not mount this product upside down for an extended
period of time as it may cause permanent damage to the
screen.
Rest your eyes periodically by focusing on an object at
least 5 feet away. Blink often.
Do not place any objects onto the monitor and do not use
the monitor outdoors.
Position the monitor at a 90° angle to windows and other
light sources to minimize glare and reflections.
•
•
If glass is broken, handle with care.
Clean the LCD monitor surface with a lint-free, non-
abrasive cloth. Avoid using any cleaning solution or glass
cleaner!
Temperature controlled fans are implemented in this
monitor. For reliable performance and long useful life of
this product, it is mandatory to not cover any vents on the
monitor.
•
•
Adjust the monitor’s brightness, contrast and sharpness
controls to enhance readability.
•
•
If monitor or glass is broken, do not come in contact with
the liquid crystal and handle with care.
Avoid reproduction of still patterns on the monitor for long
periods of time to avoid image persistence (after image
effects).
Allow adequate ventilation around the monitor, so that
heat can properly dissipate. Do not block ventilated
openings or place the monitor near a radiator or other
heat sources.
•
Get regular eye checkups.
Ergonomics
To realize the maximum ergonomic benefits, we recommend
the following:
•
•
Do not put anything on top of the monitor.
Handle with care when transporting. Save packaging for
transporting.
•
Use the preset Size and Position controls with standard
signals.
•
•
If using the cooling fan continuously, it is recommended to
wipe holes clean a minimum of once a month.
•
•
•
Use the preset Color Setting.
Use non-interlaced signals.
To ensure the monitor’s reliability, please clean the holes
at the back side of the cabinet at least once a year to
remove dirt and dust.
Do not use primary color blue on a dark background, as
it is difficult to see and may produce eye fatigue due to
insufficient contrast.
•
When using a LAN cable, do not connect to a peripheral
device with wiring that might have excessive voltage.
•
Suitable for entertainment purposes at controlled
luminous environments, to avoid disturbing reflections
from the screen.
* The product you purchased may not have this feature.
English-3
Cleaning the LCD Panel
•
When the liquid crystal panel is dusty, please gently wipe
with a soft cloth.
•
•
•
Please do not rub the LCD panel with hard material.
Please do not apply pressure to the LCD panel surface.
Please do not use OA cleaner as it will cause
deterioration or discoloration on the LCD panel surface.
Cleaning the Cabinet
•
•
•
Unplug the power supply
Gently wipe the cabinet with a soft cloth
To clean the cabinet, dampen the cloth with a neutral
detergent and water, wipe the cabinet and follow with a
dry cloth.
NOTE:
DO NOT clean with benzene thinner, alkaline
detergent, alcoholic system detergent, glass
cleaner, wax, polish cleaner, soap powder, or
insecticide. Rubber or vinyl should not be in
contact with the cabinet for an extended period
of time. These types of fluids and materials can
cause the paint to deteriorate, crack or peel.
English-4
Installation
For contents, please refer to the contents sheet.
To prevent the LCD monitor from falling off from the wall or
ceiling, NEC strongly recommends using a safety wire.
This device cannot be used or installed without the Tabletop
Stand or other mounting accessory for support. For proper
installation it is strongly recommended to use a trained,
NEC authorized service person. Failure to follow NEC
standard mounting procedures could result in damage to the
equipment or injury to the user or installer. Product warranty
does not cover damage caused by improper installation.
Failure to follow these recommendations could result in
voiding the warranty.
Please install LCD monitor in a spot of the wall or ceiling
strong enough to support the monitor.
Prepare the LCD monitor using mounting accessories such
as hook, eyebolt or mounting parts and then secure the LCD
monitor with a wire. The safety wire must not be tight.
CAUTION: Do not attempt to hang the monitor using an
installation safety wire. The monitor must be
properly installed.
Mounting
Please make sure the mounting accessories are strong
enough to support the LCD monitor before mounting it.
DO NOT mount the monitor yourself. Please ask your
supplier. For proper installation it is strongly recommended to
use a trained, qualified technician. Please inspect the location
where the unit is to be mounted. Mounting on wall or ceiling
is the customer’s responsibility. Not all walls or ceilings are
capable of supporting the weight of the unit. Product warranty
does not cover damage caused by improper installation, re-
modeling, or natural disasters. Failure to comply with these
recommendations could result in voiding the warranty.
CAUTION: If you use handles for safety wire please refer to
Handles for safety wire below.
Handles for safety wire
: Factory set position.
: Alternate position.
Solid line: Handle placement for safety wire in landscape
DO NOT block ventilated openings with mounting
accessories or other accessories.
position.
Dotted line: Handle placement for safety wire in portrait
position.
For NEC Qualified Personnel:
To ensure safe installation, use two or more brackets to
mount the unit. Mount the unit to at least two points on the
installation location.
C751Q/C861Q
Please note the following when mounting
on wall or ceiling
•
NEC recommends mounting interfaces that comply with
UL1678 standard in North America.
•
NEC strongly recommends
using size M8 screws
Mounting
Bracket
Unit
No gap
(15-17 mm + thickness
of bracket and washers in
length). If using screws
longer than 15-17 mm,
check the depth of the hole.
(Recommended Fasten
Force: 1125 - 1375 N•cm).
No thread
4 mm
Washers
Screw
C981Q
under
10 mm
15-17 mm
Thickness
of bracket
and washers
Bracket hole should be under 10 mm.
•
Prior to mounting, inspect the installation location to
ensure that it is strong enough to support the weight of
the unit so that the unit will be safe from harm.
•
•
•
For detailed information, refer to the instructions included
with the mounting equipment.
Make sure that there is no gap between the monitor and
the bracket.
When used in a video wall configuration for a longer
time, slight expansion of the monitors may happen due to
temperature changes. Due to this it is recommended that
over one millimeter gap is kept between adjacent monitor
edges.
•
When installing, do not apply pressure to the screen or
excessive force to any part of the monitor by pushing
or leaning on it. This may cause the monitor to become
distorted or damaged.
English-5
Changing handles position
: Factory set position.
: Alternate position.
CAUTION: Four or more handles are required when
transporting.
C751Q
C861Q
C981Q
Changing NEC logo ornament position
When using the monitor in the portrait position, the NEC logo
ornament position can be changed.
Removing the logo ornament: unscrew the installed screw
then take off the logo ornament.
Attaching the logo ornament: make sure the holes for the
screws on the logo ornament and the holes for the screws
on the bezel are aligned. Install the logo ornament with the
screws, which are used for installing the logo ornament.
(Recommended Fasten Force: 30-40N•cm).
Screw holes
LED Indicator
CAUTION: Do not use any other screw to install the logo
ornament.
Mounting Interface (M8)
Attaching Mounting Accessories
The monitor is designed for use with the VESA mounting
system.
1. Attach eyebolts (not included) for
mounting
This model is equipped with attachable eyebolts to aid in
mounting.
•
•
Install the eyebolt brackets with the attached screws.
Screw the eyebolts into eyebolt holes in eyebolt brackets
as shown in the picture.
600 mm
•
•
Be sure eyebolts are secure.
In order to move the monitor into position, use a lifting
device attached to the eyebolts.
3. Using an Option Board
1. Turn off the main power switch.
CAUTION: DO NOT mount the monitor using only the
eyebolts. Eyebolts are for tentative use only.
2. Place the monitor face down on the protective sheet.
NOTE: Be sure to place the monitor on a flat and adequate
space.
3. Remove the attached slot cover by unscrewing the
installed screws (Figure 1), sliding to right (Figure 2) and
moving up (Figure 3).
2. Attach Mounting Accessories
Be careful to avoid tipping the monitor when attaching
accessories.
VESA Mounting Interface (M8)
Figure 1
Figure 2
400 mm
Figure 3
Figure 4
Mounting accessories can be attached with the monitor in
the face down position. To avoid damaging the front face,
place the protective sheet on the table underneath the LCD
monitor. The protective sheet was wrapped around the LCD
monitor in the original packaging. Make sure there is nothing
on the table that can damage the monitor.
4. Insert the option board into the monitor and fix it with the
removed screws (Figure 4).
NOTE:
Please contact your supplier for available option
boards.
Do not apply excessive force to manipulate the
option board before fixing it with screws.
Make sure that the board is inserted into the slot in
the correct orientation.
NOTE:
Prior to installation, be sure to place the monitor
on a flat area with adequate space.
NOTE:
You can use 600 mm/400 mm holes for mounting.
CAUTION: Ensure the option board is attached by the
removed screws. Otherwise, the option board
may fall out and expose you to danger.
(Recommended Fasten Force: 139 - 189N•cm).
English-7
4. Installing and removing the optional
table top stand
5. Prevent Tipping
When using the display with the optional table top stand,
fasten the LCD to a wall using a cord or chain that can
support the weight of the monitor in order to prevent the
monitor from falling. Fasten the cord or chain to the monitor
using the provided clamps and screws that are included with
the optional table top stand.
CAUTION: Installing and removing the stand must be done
by four or more people.
For installation, follow the instructions included with the
stand or mounting equipment. Use only those devices
recommended by the manufacturer.
NOTE:
ONLY use screws which are supplied with the
optional table top stand.
Cord or chain
Clamp
Screw (M4)
When installing the LCD monitor stand, handle the unit with
care to avoid pinching your fingers.
Optional table top stand
Screw Holes
Table
Protective Sheet
NOTE:
NOTE:
Install the stand in the direction of the arrow
which is imprinted on the surface of the stand.
Use the ST-801.
Without eyebolt brackets
C981Q: DO NOT use this monitor on the floor with
the table top stand. Please use this monitor on a
table or with a mounting accessory for support.
Cord or chain
Clamp
Screw (M4)
Screw Holes
With eyebolt brackets
Before attaching the LCD monitor to the wall, make sure that
the wall can support the weight of the monitor.
Be sure to remove the cord or chain from the wall before
moving the LCD.
English-8
6. Ventilation Requirements
When mounting in an enclosed space or recessed area,
leave adequate room between the monitor and the enclosure
to allow heat to disperse, as shown below.
100 mm
30 mm
100 mm
Must be under 40 Degree Celsius.
Allow adequate ventilation or provide air conditioning around
the monitor, so that heat can properly dissipate away from
the unit and the mounting equipment; especially when you
use monitors in a multiple screen configuration.
NOTE:
The sound quality of the internal speakers will be
different depending on the acoustics of the room.
English-9
Parts Name and Functions
Control Panel
A Power Button (
)
H Menu/Exit Button (MENU/EXIT)
Activates the OSD menu when the OSD menu is turned off.
Acts as a back button within the OSD to move to the previous
OSD menu.
Acts as an EXIT button to close the OSD when on the main
menu.
B Mute Button (MUTE)
Switches the audio mute on/off.
C Input/Set Button (INPUT/SET)
INPUT: Toggle switches between below inputs.
I Remote Control Sensor and Power Indicator
Receives the signal from the remote control (when using the
Glows blue when the LCD monitor is in active mode*.
Green and Amber blink alternately when the “SCHEDULE
SETTINGS” function is enabled*1.
[DisplayPort1], [DisplayPort2], [HDMI1], [HDMI2], [HDMI3],
[MP], [OPTION*]. These are available inputs only, shown as
their factory preset name.
SET: When OSD (On Screen Display) is shown, this button
acts as a “set button” when you make a selection.
*: This function depends on which option board you are using.
When a component failure is detected within the monitor, the
indicator will blink red or blink a combination of red and blue.
* If “OFF” is selected in the “POWER INDICATOR”
active mode.
D Plus Button (+)
Increases the audio output level when the OSD menu is
turned off.
Acts as (+) button to increase the adjustment within the
OSD menu.
*1 If “OFF” is selected in the “SCHEDULE INDICATOR”
E Minus Button (-)
Decreases the audio output level when the OSD menu is
turned off.
Acts as (-) button to decrease the adjustment within the
OSD menu.
J Room Light Sensing Sensor
Detects the level of ambient light, allowing the monitor
to make automatic adjustments to the backlight setting,
resulting in a more comfortable viewing experience. Do not
F Up Button (
)
Activates the OSD menu when the OSD menu is turned off.
Acts as button to move the highlighted area up to select
adjustment items within the OSD menu.
G Down Button (
)
Activates the OSD menu when the OSD menu is turned off.
Acts as button to move the highlighted area down to select
adjustment items within the OSD menu.
English-10
Terminal Panel
USB Upstream
A AC IN Connector
J USB Port
Connects with the supplied power cord.
USB1:
Downstream port (USB Type-A).
Connect USB devices.
B Main Power Switch
On/Off switch to turn main power ON/OFF.
USB2:
Upstream port (USB Type-B).
Connect external equipment such as a computer.
To control the monitor from connected external
equipment, please use this port.
C Audio IN
USB CM1 (2A): Power supply port.
Audio signal input from external equipment such as a
computer or player.
USB CM2: Service port. Please do not connect devices.
USB MP: USB storage device port. This port is for future
software upgrades.
D DisplayPort OUT
To use the Media Player, please connect USB
MP is an abbreviation of Media Player.
Output DisplayPort signals from DisplayPort IN1.
You can connect multiple monitors by using DisplayPort
K LAN Port 1/2 (RJ-45)
NOTE: Please give priority for use to LAN1.
E DisplayPort IN1/IN2
DisplayPort signals input.
L Audio OUT
Audio signal output from the AUDIO IN, DisplayPort and
HDMI to an external device (stereo receiver, amplifier, etc.).
NOTE: This connector is not a Headphone terminal.
F HDMI IN1/IN2/IN3
Digital HDMI signals input.
G RS-232C IN (D-Sub 9 pin)
Connect RS-232C input from external equipment such as a
computer in order to control RS-232C functions.
M Internal/External Speaker Switch
: Internal speaker
: External speaker.
NOTE: Please turn off the monitor’s main power when you
H Remote IN
use the Internal/External speaker switch.
Use the optional sensor unit by connecting it to your monitor.
NOTE: Do not use this connector unless specified.
N External Speaker Terminal
Audio signal output.
Red terminal is plus (+).
I microSD Card Slot
Black terminal is minus (-).
NOTE: This speaker terminal is for 15 W + 15 W (8 ohm)
speaker.
Insert a microSD memory card. To use the Media Player,
please connect a microSD memory card to this port
To install the microSD card slot cover, please refer to
O Internal Speaker
English-11
P Option Board Slot
Slot 2 type accessory is available. Please contact your
supplier for detailed information.
NOTE: Please contact your supplier for available option board.
Q Security Slot
Security and theft protection lock compatible with
Kensington security cables/equipment.
For products, visit Kensington’s website,
R Rating Label
S Intelligent Wireless Data Sensor
Sensor for wireless communication of monitor for information
and settings.
T Option Speaker Mounting Hole
NOTE: Please contact your supplier for available optional
speaker.
English-12
Wireless Remote Control
J UP/DOWN Button (
/
)
Acts as button to move the highlighted area up or down
to select adjustment items within the OSD menu.
When using PIP (picture in picture), moves the small screen
up or down.
K MINUS/PLUS (-/+) Button
Increases or decreases the adjustment level within the OSD
menu settings.
When using PIP (picture in picture), moves the small screen
left or right.
L SET/POINT ZOOM Button
SET: When OSD is shown, this button acts as “set button”
when you make a selection.
POINT ZOOM: When OSD is not shown, this button acts as
“point zoom button”.
MVOLUME UP/DOWN Button (VOL +/-)
Increases or decreases the audio output level.
N CH/ZOOM UP/DOWN Button (CH/ZOOM +/-)*1
Increases or decreases the POINT ZOOM level.
O GUIDE Button*1
P MUTE Button
Turns on/off the mute function.
Q PICTURE MODE Button
Selects the picture mode, [HIGHBRIGHT], [STANDARD],
[sRGB], [CINEMA], [CUSTOM1], [CUSTOM2],
A POWER ON/STANDBY Button
Switches the power on/standby.
HIGHBRIGHT: For moving images such as DVD.
STANDARD: For images.
sRGB: For text based images.
B INPUT Button
Selects the input signal.
Input signal for the MEDIA PLAYER is shown as MP.
CINEMA: For movies.
CUSTOM1 and CUSTOM2: Custom setting.
SVE-(1-5) SETTINGS: For images and movies.
C OPTION MENU Button
D KEYPAD
R ASPECT Button
Selects the picture aspect, [FULL], [WIDE]*, [DYNAMIC]*,
* HDMI1, HDMI2, HDMI3 inputs only.
Press the buttons to set and change passwords, change
channel and set REMOTE ID.
Below buttons are used for CEC (Consumer Electronics
, 2 , 3
, 5 , 6
.
S AUDIO INPUT Button
Selects the audio input source [IN], [HDMI1], [HDMI2],
E ENT Button
Confirm the AUTO PLAY FOLDER in Media Player.
[HDMI3], [DisplayPort1], [DisplayPort2], [OPTION]*1, [MP].
T STILL Button
ON/OFF button: Activates/deactivates still picture mode.
CAPTURE button: Captures still picture.
NOTE: This function deactivates when selecting MULTI
PICTURE MODE, TEXT TICKER, SCREEN SAVER, POINT
ZOOM, IMAGE FLIP except for NONE, SUPER in INPUT
CHANGE, TILE MATRIX.
If input signal is OPTION, this button’s actions depend on
which option board you are using.
F DISPLAY Button
If you lock remote control buttons using the IR LOCK
SETTINGS function, you can unlock the buttons by holding
down this DISPLAY button for more than 5 seconds.
G MENU Button
Turns on/off the menu mode.
H AUTO SET UP Button (This button does not work)
I EXIT Button
Returns to the previous menu within the OSD menu.
*1: This button’s action depends on which option board you are using.
English-13
IMAGE FLIP Button
Operating Range for the Remote
Control
Point the top of the remote control toward the LCD monitor’s
remote control sensor during button operation.
Toggle switches between [H FLIP], [V FLIP], [180° ROTATE]
ACTIVE PICTURE Button
Selects active picture.
Use the remote control within a distance of about 7 m (23 ft.)
from the remote control sensor, or at a horizontal and
vertical angle of within 30° and within a distance of about
3.5 m (10 ft.).
MULTI PICTURE Button
ON/OFF Button: Toggle switches between ON and OFF.
MODE Button: Selects a mode from PIP (picture in picture)
or PBP (picture by picture).
CHANGE Button: Swaps images between two pictures.
PICTURE ASPECT Button: Selects active picture frame
aspect.
NOTE: Enable to change each multi picture size by pressing
SET/POINT ZOOM button during multi picture mode.
REMOTE ID Button
MTS Button*1
*1: This button’s action depends on which option board you are using.
Refer to the option board’s user’s manual for further information.
Caution: Important, the remote control
system may not function when
direct sunlight or strong
illumination strikes the
NOTE:
The buttons with no explanation do not function.
remote control sensor, or
when there is an object in
the path.
Handling the remote control
•
Do not expose to strong shock.
•
Do not allow water or other liquid to
splash on the remote control. If the
remote control gets wet, wipe it dry immediately.
•
•
Avoid exposure to heat and steam.
Except to install the batteries, do not open the remote
control.
English-14
Setup
NEC recommends the following battery use:
1. Determine the installation location
CAUTION: Installing your LCD monitor must be done by a
qualified technician. Contact your supplier for
more information.
•
Place “AAA” size batteries matching the (+) and (-) signs
on each battery to the (+) and (-) signs of the battery
compartment.
•
•
Do not mix battery brands.
CAUTION: MOVING OR INSTALLING THE LCD MONITOR
MUST BE DONE BY FOUR OR MORE PEOPLE.
Failure to follow this caution may result in injury if
the LCD monitor falls.
Do not combine new and old batteries. This can shorten
battery life or cause liquid leakage of batteries.
•
Remove dead batteries immediately to prevent battery
acid from leaking into the battery compartment.
CAUTION: Do not mount or operate the monitor upside
•
Do not touch exposed battery acid, it may injure your skin.
down.
NOTE:
If you do not intend to use the Remote Control for
a long period of time, remove the batteries.
CAUTION: This LCD monitor has internal temperature
sensors and cooling fans, including a fan for the
option board.
3. Connect external equipment
If the LCD monitor becomes too hot, the cooling
fans will turn on automatically.
•
To protect the external equipment, turn off the main power
The option board’s fan is active although the
temperature is lower than normal operating
temperature for cooling the option board. If the
LCD monitor becomes overheated while the
cooling fan is running, a “Caution” warning will
appear. If the “Caution” warning appears, stop
using the unit and allow it to cool. Using the
cooling fans will reduce the likelihood of early unit
failure and may help reduce image degradation
and “Image Persistance”.
If the LCD monitor is used in an enclosed area
or if the LCD panel is covered with a protective
screen, please check the inside temperature of
the monitor by using the “HEAT STATUS” control
higher than the normal operating temperature,
please turn the cooling fan to ON within the FAN
before making connections.
•
Refer to the user’s manual of your equipment for further
information.
NOTE:
Do not connect/disconnect cables when turning
on the monitor or other external equipment, as this
may result in a loss of the monitor image.
4. Connect the supplied power cord
•
•
•
The equipment should be installed close to an easily
accessible power outlet.
Fasten the power cord to the LCD monitor by attaching
the screw and clamp.
Fully insert the prongs into the power outlet socket.
A loose connection may cause image degradation.
NOTE:
Please refer to the “Safety Precautions and
Maintenance” section of this user’s manual for
proper selection of an AC power cord.
IMPORTANT: Lay the protective sheet beneath the
monitor, so as not to scratch the LCD panel.
The protective sheet was wrapped around the
monitor when it was packaged.
(Recommended Fasten Force: 139 - 189N•cm).
2. Install the remote control batteries
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
Screw
Clamp
A. Press and slide to open the cover.
B. Align the batteries according to the (+) and (–) indications
inside the case.
C. Replace the cover.
CAUTION: Incorrect usage of batteries can result in leaks or
bursting.
English-15
5. Switch on the power of all the attached
external equipment
When connected with a computer, switch on the power of the
computer first.
6. Operate the attached external equipment
Show the signal on the screen from the desired input source.
7. Adjust the sound
Make volume adjustments when required.
Make adjustments such as backlight or contrast when
required.
9. Recommended Adjustments
To reduce the risk of the “Image Persistence”, please adjust
the following items based on the application being used:
It is recommended that the “FAN CONTROL” setting
English-16
Connections
NOTE:
Do not connect or disconnect cables when turning on the monitor’s main power or other external equipment’s power,
as this may result in a loss of the monitor image.
NOTE:
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
Before making connections:
*
*
*
First turn off the power of all the attached equipment and make connections.
Refer to the user’s manual included with each separate piece of equipment.
We strongly recommend connecting or disconnecting a USB storage device or a microSD memory card to the monitor when
the monitor’s main power is off.
Wiring Diagram
Stereo Amplifier
USB devices
such as
USB camera or
USB memory
USB cable
USB1
USB2
Devices that
require power
supply:
USB CM1 (2A)
USB CM2
USB port
(Type-A)
USB port
(Type-B)
Computer (USB)*1
Ex:
MultiPresenter
Stick
USB MP
DVD Player (HDMI) or
Computer (HDMI)
USB storage device
DVD Player
(HDMI)
AV
Amplifier
Computer (DisplayPort)
Computer (DisplayPort)
AV Amplifier
DVD Player or
Computer
Second monitor*
Computer
DVD Player
(HDMI)
Dotted lines = other signal
Solid lines = video signal
DVD Player
Stereo Amplifier
Dashed lines = audio signal
VCR player or DVD player
*: Multiple monitors that are daisy-chained have a limit to the connectable monitors.
*1: The device connected to USB2 can control the device connected to USB1.
English-17
Connecting a Personal Computer
Connecting your computer to your LCD monitor will enable you to reproduce your computer’s video signal output.
Some display cards may not be able to support the required resolution for proper image reproduction.
Your LCD monitor shows proper image by adjusting the factory preset timing signal automatically.
<Typical factory preset signal timing>
Scanning frequency
HDMI
MODE1 MODE2
DisplayPort
1.1a
Resolution
Horizontal
31.5 kHz
37.9 kHz
48.4 kHz
45.0 kHz
47.8 kHz
49.7 kHz
64 kHz
Vertical
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
30 Hz
30 Hz
60 Hz
60 Hz
24 Hz
60 Hz
1.2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
640 x 480
800 x 600
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes*1
No
1024 x 768
1280 x 720
1280 x 768
1280 x 800
1280 x 1024
1360 x 768
1366 x 768
1400 x 1050
1440 x 900
1600 x 1200
1680 x 1050
1920 x 1080
1920 x 1200
1920 x 2160
3840 x 2160
3840 x 2160
3840 x 2160
3840 x 2160
4096 x 2160*3
4096 x 2160*3
47.7 kHz
47.7 kHz
65.3 kHz
55.9 kHz
75.0 kHz
65.3 kHz
67.5 kHz
74.6 kHz
133.3 kHz
65.7 kHz
67.5 kHz
133.3 kHz
135.0 kHz
54.0 kHz
135.0 kHz
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes*1
No
Yes
Yes
Yes*1
Yes
Yes
No
No
No
Yes*1, *2
Yes*2
No
No
Yes
No
No
No
*1: Recommended resolution.
*2: Only HBR2 is set.
*3: Compressed image.
Connecting a Player or Computer with HDMI
•
•
•
•
•
•
Please use an HDMI cable with the HDMI logo.
It may take a moment for the signal to appear.
Some display cards or drivers may not display an image correctly.
Please check display card when image is compressed with 3840 x 2160.
To output HDMI audio, set [HDMI1], [HDMI2] or [HDMI3] at AUDIO INPUT in the OSD or choose [HDMI1], [HDMI2] or
[HDMI3] by the remote control AUDIO INPUT button.
•
•
If the input resolution is 3840 x 2160 (60 Hz) and 4096 x 2160 (60 Hz), please set MODE2 at HDMI in TERMINAL
If the monitor’s main power is turned on after a connected computer is turned on, sometimes images are not displayed.
In this case, please turn off the computer then turn it on again.
Connecting a Computer with DisplayPort
•
•
•
•
•
•
Please use a DisplayPort cable with the DisplayPort compliance logo.
It may take a moment for the signal to appear.
When connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not appear.
Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.
To output DisplayPort audio, set [DisplayPort1] or [DisplayPort2] at AUDIO INPUT in the OSD or choose [DisplayPort1] or
[DisplayPort2] by the remote control AUDIO INPUT button.
•
•
To display individual images at each connected monitors with the DisplayPort out connector, please set DisplayPort1.2 and
If the monitor’s main power is turned on after a connected computer to the monitor is turned on, sometimes images are not
displayed. In this case, please turn off the computer then turn it on again.
English-18
Connecting a USB device
USB1:
USB downstream port (Type-A).
Connect a USB compatible flash memory or keyboard to Down Stream Port.
USB2:
USB upstream port (Type-B).
Connect to a USB compatible computer with a USB cable.
A USB compatible computer connected to USB2 can control the devices connected to USB1.
USB CM1 (2A): Power supply port.
USB CM2:
Service port.
Please do not connect devices.
USB MP:
USB downstream port (Type-A).
To use the Media Player function, please use this port.
•
•
Please make sure the connector shape and orientation is correctly aligned when connecting the USB device or cable.
Depending on the use of computer BIOS, OS or device, the USB function may not be working. In this case, please check
user’s manual of your computer or device, or contact your supplier for detailed information.
•
•
Before turning off the main power switch of the monitor or shutting down Windows®, please turn off the USB function and
remove the USB cable from the monitor. You may lose data when the computer crashes.
It may take a few seconds until the monitor recognizes the USB input. Do not disconnect the USB cable or disconnect and
reconnect the USB cable before the monitor recognizes the input.
•
•
•
•
When you use the USB CM1 (2A) port for power supply, please use a USB cable that supports 2A.
Do not bind the USB cable. It may cause heat or fire.
NOTE:
USB CM1 (2A) and USB CM2 are not corresponding port.
English-19
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will turn blue while powered on.
NOTE:
The Main Power switch must be in the ON position in order to power up the monitor using the remote control or the
Power button.
OFF
ON
Main Power Switch
Power Button
Using the remote control
POWER ON button
English-20
Power Indicator
LED indicator
Aspect
For MP
status and
lighting pattern
Condition
Recovery
FULL
ZOOM
NORMAL
Glowing blue
Blinking green*1
Normal
For DisplayPort1, DisplayPort2, OPTION*1
FULL 1:1 ZOOM NORMAL
Under any of the conditions
below, no input signal has been
detected by the monitor during
the period of time you set:
For HDMI1, HDMI2, HDMI3
FULL WIDE DYNAMIC
•
The monitor is using an
option board.
1:1
ZOOM
NORMAL
1. Turn on the monitor
by the remote
control or the
•
INPUT DETECT is set to a
setting except for NONE.
•
•
USB POWER is set to ON.
*1: This function depends on which option board you are using.
monitor button.
DisplayPort in the TERMINAL
MODE is set to MST.
2. Send an AV signal
input to the monitor.
Glowing amber
Blinking amber
Glowing red
No AV signal input has been
detected by the monitor during
the period of time you set.
(with network signal input)
Aspect ratio
of image
Recommended selection
for picture aspect*3
NORMAL
Unchanged view*3
No AV signal input has been
detected by the monitor during
the period of time you set.
(no network signal input)
4:3
DYNAMIC
FULL
Turn off the monitor by the
remote control or the monitor
button.
Turn on the monitor by
the remote control or
the monitor button.
*1: Time setting for AUTO POWER SAVE is available at POWER SAVE
NOTE:
If the indicator is blinking red in a combination
of long and short, a certain failure might have
occurred, please contact your supplier.
Squeeze
Letterbox
WIDE
Using Power Management
This LCD monitor follows the VESA approved DPM (Display
Power Management) function.
*3 Grey areas indicate unused portions of the screen.
The power management function is an energy saving
function that automatically reduces the power consumption
of the monitor when the keyboard or the mouse has not been
used for a fixed period.
NORMAL: Reproduces the aspect ratio that is sent from the
source.
FULL: Fills the entire screen.
This allows your LCD monitor to enter a Power Management
mode if the monitor’s POWER SAVE function is set to
ENABLE, and a certain amount of time has passed since the
monitor recognized “no signal input”. It will increase the life
and decrease the power consumption of the monitor.
WIDE: Expands a 16:9 letterbox signal to fill the entire
screen.
DYNAMIC: Expands a 4:3 pictures to fill the entire screen
with non-linearity. Some of the outside image area will be cut
off due to expansion.
NOTE:
Depending on the computer and display card
used, this function may not operate.
After the video signal was lost, the monitor
automatically goes into OFF at a preset time
period.
1:1: Shows the image in a 1 by 1 pixel format.
ZOOM
The image can be expanded beyond the active screen area.
The image which is outside of the active screen area is not
shown.
ZOOM
ZOOM
English-21
Media Player
Plays saved data, such as still and motion images, BGM (Background Music), on a USB storage device or microSD memory
card connected to the monitor.
Top screen of the viewer
•
•
Select [SETTINGS] to change the media player settings.
While “AUTO PLAY” has been set to SLIDESHOW in SETTINGS, the monitor starts performing “AUTO PLAY” by the
operation below:
- When connecting a USB storage device to the USB MP (Terminal Panel page 11), with the monitor already powered ON
and the Media Player top screen displayed.
- When powering ON the monitor with a USB storage device already connected, and Media Player was the input source at
the last power OFF.
For starting “AUTO PLAY”, the system will automatically search the folder which is set in the AUTO PLAY settings FOLDER
field, in the USB storage device and then display found still images or movies. The images and movies will be displayed in the
“Sorted” order.
NOTE:
Only 1 USB storage device can be recognized by the viewer.
A window will appear when you press the control panel buttons while the Media Player is active. You can select to control either
the OSD menu or the Media Player from the window that opens.
If Media Player contents are played while TILE MATRIX is active, the image play timing might have a gap within monitors.
If a monitor is used in portrait position, please set OSD ROTATION to PORTRAIT. Image orientation is changed according to
what you set at OSD ROTATION.
When OSD ROTATION is set to PORTRAIT, please use the motion image, which is rotated anticlockwise by 90°.
Displayable/playable files
Still
Supported formats
File extension
.jpg, .jpeg, .jpe
.png
Supported
Baseline, Progressive, RGB, CMYK
Interlace, α channel
Motion image
Supported formats
File extension
.mpg, .mpeg
.wmv
Video codec
MPEG1, MPEG2
H.264, WMV
H.264
Audio codec
MPEG Audio Layer3 (Abbreviation: MP3) AAC-LC (Abbreviation: AAC), LPCM
MP3, WMV Standard, WMA 9/10 Professional
.mp4
MP3, AAC
MP3, AAC
MP3, AAC
.mov
H.264
.flv, .f4v
H.264
English-22
BGM
Supported formats
File extension
.wav
Audio codec
LPCM
.mp3
MP3
Information
Item
Conditions
JPEG
PNG
Resolution
5000x5000
4000x4000
MPEG1
MPEG2
H.264
WMV
-
480@30fps
MP@ML, MP@HL, 1080p@30fps / 1080i@60fps
High profile Lv.4.2, 1080p@30fps / 1080i@60fps
Advanced@L3, Simple&Main
Up to 15Mbps
Video bit date
Audio sampling rate
Audio bit rate
-
Up to 48KHz
MP2
Up to 384Kbps
MP3
Up to 320Kbps
AAC
Up to 1440Kbps
NOTE:
Depending on the file, it may not play even when it satisfies all above mentioned conditions.
Depending on network environments, the type of USB storage device, and file bitrate, it may not play still image files.
You cannot play DRM (Digital Right Management) files.
The maximum resolution for a motion image is 1920 (Horizontal) x 1080 (Vertical).
Compatible microSD memory card
Format a microSD memory card in the FAT32 format or FAT16 format.
Refer to the computer’s instruction user’s manual or Help file on how to format a microSD memory card.
Information
Up to 32GB microSDHC is supported.
NOTE:
It is not guaranteed to work with all microSD memory card sold commercially.
microSD with CPRM is not supported.
microSD UHS-1 or UHS-2 are not supported.
•
•
When inserting a microSD memory card, please make sure of the microSD memory card direction then insert it correctly.
When ejecting a microSD memory card from the microSD card slot, press the center of the microSD memory card then take
it out.
Installing microSD card slot cover
To secure your microSD memory card, we recommend you install the microSD card slot cover.
Please insert the edge of the microSD card cover to the hole. (Recommended Fasten Force: 139 - 189N•cm).
Hole
microSD card cover is set.
English-23
Compatible USB memory
Format a USB memory in the FAT32 format or FAT16 format for using it in the Media Player. Refer to the computer’s instruction
user’s manual or Help file on how to format a USB memory.
Please use a USB memory with this monitor in accordance with the drawing below.
If the physical size of the USB device is larger than the supported sizes listed below, please use a USB extension cable.
USB memory
Extension cable
Under 7.8 mm
NOTE:
Check the format if this device cannot recognize the connected USB memory.
It is not guaranteed to work with all USB memories sold commercially.
File display screen
The files can be displayed using either icons or thumbnails in the Media Player.
Icon display
RETURN
Goes back one subsequent level higher.
PAGE UP
Displays a list of the previous files.
Displays a list of the next files.
Displays the setting screen.
PAGE DOWN
SETTINGS
THUMBNAILS/ICON Switches between thumbnail display and icon display.
SORT
Changes the order to display files by name (filename), type (file extension), date (date of creation), or size
(file capacity). The default sorting order is by “Name”.
EJECT
Disconnects from the USB storage device or the microSD memory card inserted to the monitor. Please
select EJECT when file list is displayed.
NOTE:
The maximum number of files that can be displayed in a folder including folder icons is 300.
A folder hierarchy is shown up to level 16.
The icon of a file whose type cannot be determined is indicated by a “?”.
Depending on the file, thumbnail cannot be displayed.
English-24
Slideshow display
•
•
Select a folder that contains images or movies.
A slideshow can be displayed using “MANUAL” in which the images are switched by operating a button on the remote
control, or “AUTO” in which the images are switched automatically at a set interval (PLAY MODE is “AUTO”).
•
•
•
The default factory setting is “MANUAL”. To perform “AUTO”, set the “PLAY MODE” to “AUTO”.
The images will be displayed in the order selected under “Sort” on the file display screen.
When still images in high resolutions are displayed as the Slideshow, it may go back to the file display screen.
Media Player settings
Select the
icon in the file list screen or top screen of the Media Player to display the configuration screen of the Media Player.
The following settings can be configured on the configuration screen.
SLIDESHOW
Menu
Function
SCREEN SIZE
PLAY MODE
INTERVAL
REPEAT
Selects ACTUAL SIZE or BEST FIT.
Selects AUTO or MANUAL.
Sets interval time.
Check the check box to repeat slideshow.
Selects an audio file.
AUDIO FILE
BGM
Check the check box to enable BGM.
PLAY END SCREEN
Selects a setting for when the slideshow finishes.
BLACK SCREEN: When the slideshow finishes, a black screen is displayed.
FILE LIST: When the slideshow finishes, it goes back to the file list screen.
SAVE LAST SCREEN: When the slideshow finishes, the last slideshow image is kept on the screen.
AUTO PLAY
Automatically displays selected folder when the monitor is turned on with MP as the selected input.
Menu
Function
AUTO PLAY
OFF: Automatic play mode is off.
SLIDESHOW: Automatically plays a selected file.
Select a file by SET/POINT ZOOM button and confirm by ENT button.
FOLDER
PRESET CONTENTS
Plays selected folder when the monitor has no signal input.
Menu
Function
ENABLE
FOLDER
Check the check box to enable preset contents.
Select a file by SET/POINT ZOOM button and confirm by ENT button.
Please press OK to activate above settings.
If OK is not pressed, settings that you set are not activated.
English-25
NETWORK & OTHER SETTINGS
Below are the options for the Network settings and Shared Folder settings for the Media Player.
To select the settings, press the remote control SET/POINT ZOOM button on the NETWORK & OTHER SETTINGS.
NETWORK SETTINGS for MEDIA PLAYER
Menu
Function
IP SETTING
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
DNS
Set these settings.
DNS PRIMARY
DNS SECONDARY
NETWORK INFORMATION for the Media Player displays what you set in the NETWORK SETTINGS for the Media Player.
SHARED FOLDER
There are two settings for configuring the SHARED FOLDER.
Press the remote control SET/ZOOM button to open the shared settings options.
•
SHARED SD CARD SETTINGS
Folders saved in a computer on the network can be copied to the connected microSD memory card using a web browser on
the connected computer.
Menu
ENABLE
USER NAME
PASSWORD
Function
Check the checkbox to enable SHARED SD CARD SETTINGS.
USER NAME is displayed. It is the same name as the monitor name and it is not changeable.
Set password.
Please press OK to activate settings in the SHARED SD CARD SETTINGS.
If OK is not pressed, settings that you set are not activated.
•
SHARED FOLDER SETTINGS.
Folders saved in a computer on the network can be copied to the connected microSD memory card by controlling the
monitor.
Menu
ENABLE
Function
Check the checkbox to enable SHARED FOLDER SETTINGS.
SHARED FOLDER Set the IP address of the network shared folder location that contains the files for copying to the microSD card.
USER NAME
PASSWORD
Set USER NAME which is used when connecting the monitor to the shared folder.
Set password.
Please press OK to activate settings in the SHARED FOLDER SETTINGS.
If OK is not pressed, settings that you set are not activated.
1 to 4 shared folders can be set.
When the connection to the shared folder fails, an error message is displayed and an “x” is displayed in the folder icon.
Carry out the following checks in this case.
- Is the name of the destination folder correct?
- Is the destination folder set for sharing?
- Have access rights been set in the destination folder?
- Are there any displayable files saved in the destination folder?
SHIFT NO SIGNAL
This setting is for a situation when the monitor detects no signal input. If ENEBLE is ticked, the monitor goes to no signal status.
The monitor detects no signal when the monitor is in the following conditions:
- After contents or images are played.
- While the monitor is displaying USB window or SD CARD window.
Menu
Function
ENABLE
Check the checkbox to enable SHIFT NO SIGNAL.
Set the time when the monitor goes into no signal after displayed detected items.
INTERVAL
Please press OK to activate settings in the SHIFT NO SIGNAL.
If OK is not pressed, settings that you set are not activated.
English-26
Using SHARED SD card SETTINGS
You can copy data to the microSD memory card, such as motion or still images, from a computer connected to the same
network as the monitor.
NOTE:
When the monitor is copying a folder, the LED indicator blinks in red.
When the monitor is in this condition, do not eject a microSD memory card from the monitor and do not turn off the
monitor’s main power. Ejecting the microSD card or turning off the monitor while copying files may corrupt the data.
If you press the STANDBY button on the remote control or the POWER button on the monitor while the LED indicator
is blinking in red, the monitor goes into standby after completing the folder copy.
Files which you can copy are still, motion image and BGM only.
Setting procedure
1. Open the Monitor LAN control of the network connected monitor then select SD-CARD VIEWER.
2. Select SEARCH to display the IP ADDRESS of the currently connected monitor and all compatible monitors on the same
network.
3. Select the IP ADDRESS of the currently connected monitor.
4. Enable upload, delete and sort files that are saved in the microSD memory card connected to the monitor.
Function
1. SELECT UPLOAD.
Press SELECT then choose the files to be copied to the microSD memory card.
File upload window appears and shows the selected files.
Once OK is selected, file uploading starts.
NOTE: Please check the microSD memory card storage capacity before copying files.
STORAGE CAPACITY shows the connected microSD memory card capacity.
2. DELETE.
Select files or folders.
DELETE FOLDERS/FILES window appears.
Once OK is selected, the selected files or folders are deleted.
3. CREATE.
A new folder is created in the microSD memory card connected to the monitor.
Insert folder name and select OK. A maximum of 255 alphanumeric characters is allowed.
English-27
4. RELOAD.
Updates microSD memory card data.
5. THUMB/LIST.
The files can be displayed using either icons or thumbnails.
Displays description of the file or folder if you select thumb name or file name.
6. SORT.
Select sort type. The folders saved in the microSD are sorted based on what you selected in sort type.
7. Connect to the other monitor’s SD-CARD VIEWER then open them.
By running the SEARCH, as described on the previous page, this window shows all compatible monitors on the same
network as the current monitor.
To open the other monitor’s web page in a new tab, right-click on its IP address. To open the other monitor’s web page in
a new window, left-click on its IP address
Using CONTENTS COPY
You can copy all data saved in a USB storage device or saved in a shared folder, which is set in the connected computer or a
server, to a microSD memory card.
1. Select CONTENTS COPY at the top screen of the Media Player.
2. Select a USB storage device or a folder.
3. Select OK to start copying. All data saved in the folder or device is copied to the microSD memory card and the original data
saved in the microSD memory card is deleted.
NOTE:
“Out of disk space” is displayed if the microSD memory card storage capacity is not enough to copy selected folders.
When contents copy has occurred, previous data that was saved in the microSD memory card is deleted.
Only devices connected to the monitor are shown.
When the monitor is copying a folder, the LED indicator blinks in red.
When the monitor is in this condition, do not eject the microSD memory card from the monitor and do not turn off the
monitor’s main power. Ejecting the microSD card or turning off the monitor while copying files may corrupt the data.
If you press the STANDBY button on the remote control or the POWER button on the monitor while the LED indicator
is blinking in red, the monitor goes to standby after completing the folder copy.
Using Emergency contents
In case of emergency sends a command to the monitor, from a computer connected to the monitor, to play the emergency
contents folder. Please create an EMERGENCY CONTENTS folder as a root folder in the microSD memory card that is
connected to the monitor.
Instructions for the EMERGENCY CONTENTS can be found on the CD included with the monitor. The file is called
“External_control.pdf”.
Information OSD
The Information OSD provides information such as: Input Source, Picture Size, etc.
Press the DISPLAY button on the remote to bring up the Information OSD.
A
B
C
D
E
F
Input name
DisplayPort1
AUDIO: IN
ASPECT: FULL
1920 X 1080
Audio input name
Picture aspect
67.5 kHz/60 Hz
Input Signal Information
Multi picture information
Communication Info
H
1920 X 1080
67.5 kHz/60 Hz
English-28
Picture Mode
Depending on the setting of SPECTRAVIEW ENGINE in the OSD PICTURE menu (see page 35), the selection choices for the
Picture Mode are different.
SPECTRAVIEW ENGINE is set to “ON”:
Select from five different picture modes, either via the OSD menu item PICTURE MODE or using the PICTURE MODE button
on the wireless remote control.
Select the Picture Mode with the wireless remote control
By pressing the Picture Mode button, the picture mode changes.
SVE-1
SVE-2
SVE-3
SVE-4
SVE-5
Select or change the Picture Mode in the OSD menu item PICTURE MODE
Select a setting from SVE-1 SETTING to SVE-5 SETTING at PICTURE MODE. Select a preset item at PRESET.
Choose the Picture Mode that is most suitable for the type of content that is shown.
•
Several modes are selectable (sRGB, Adobe®RGB SIM., eciRGB_v2 SIM., DCI SIM., REC-Bt709, HIGH BRIGHT, FULL,
DICOM SIM, PROGRAMMABLE).
•
Each PICTURE MODE includes LUMINANCE, WHITE, GAMMA, BLACK, RED, GREEN, BLUE, COLOR VISION EMU,
UNIFORMITY and METAMERISM settings.
PRESET Types
PRESET
sRGB
PURPOSE
The standard color space used for the Internet, Windows® operating systems and digital cameras.
Recommended setting for general color management.
Adobe®RGB SIM.
Provides a standard color space used in high-end graphics applications such as professional digital still cameras and
imaging.
eciRGB_v2 SIM.
DCI SIM.
Provides a color space profile recommended by ECI (The European Color Initiative).
Color setting for digital cinema.
REC-Bt709
Color setting for High-definition television.
HIGH BRIGHT
FULL
Highest brightness setting.
Native LCD panel color gamut. Suitable for use with color managed applications.
Setting that conforms to the DICOM standard for the Grayscale Standard Display Function.
DICOM SIM.
PROGRAMMABLE
For the Hardware Calibration by NEC Display Solutions GammaCompMD QA software (some OSD settings are
disabled).
MODE
PURPOSE
LUMINANCE
Adjusts the overall image and screen background brightness.
Press “LEFT” or “RIGHT” to adjust.
WHITE
Adjusts the white color by temperature or x, y setting. A lower color temperature will result in a reddish screen and a
higher color temperature in a bluish screen. A larger x value will result in a reddish screen, a larger y value changes
the screen to greenish, and smaller x,y values will change the screen to bluish white.
WHITE RANGE
0.43
3000K
0.40
5000K
0.35
6500K
0.30
15000K
WHITE TEMPERATURE
0.25
0.25
0.30
0.35
0.40
0.45 0.48
x
English-29
GAMMA
Allows you to manually select the brightness level of grayscale. There are five selections: sRGB, L STAR,
DICOM SIM. and CST. We recommend to show grayscale image data on screen.
sRGB: GAMMA setting for sRGB.
L STAR: GAMMA setting for the CIELAB color space Lab.
DICOM SIM.: DICOM GSDF (Grayscale Standard Display Function) is typically used for medical imaging.
CST: CUSTOM VALUE can be adjusted when CST is selected as the GAMMA SELECTION setting.
CUSTOM VALUE: The gamma value is selected from the range from 0.5 to 4.0 in 0.1 steps.
SAMPLE OF PRESET GAMMA
100
80
60
40
L*
sRGB
20
DICOM SIM.
Custom 1.8
Custom 2.2
0
0
64
128
192
255
GRAY STEP [0-255]
BLACK
Adjusts the black luminance.
Adjusts the color gamut.
RED
GREEN
BLUE
SAMPLE OF RGB GAMUT SETTING
0.9
LCD NATIVE GAMUT
GREEN MODIFIED
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
GREEN
SETTING
RANGE
WHITE
RED
BLUE
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
x
COLOR VISION EMU Previews various typical human vision deficiencies and is useful for evaluating how people who have such
deficiencies will perceive colors. This preview is available in four modes: Types P (Protanopia), D (Deuteranopia) and
T (Tritanopia) emulate color vision dichromacy, and Grayscale can be used for evaluating contrast legibility.
NOTE: Depending on the vision of the user, including those with color vision deficiency, there will be a variation in
how the screen's color is seen and experienced.
A simulation is used to illustrate the view of those with a color vision deficiency. It is not their actual view. The
simulation is a reproduction of those with a strong color vision mode of type P, type D or type T. People with a slight
color vision deficiency will experience little to no difference compared to those with normal color vision.
UNIFORMITY
METAMERISM
This function electronically compensates the slight variations in the white uniformity level as well as deviations
in color that may occur throughout the screen area. These variations are characteristic of LCD panel technology.
This function improves the color reproduction and evens out the non-uniformity in luminance of the monitor.
NOTE: A higher number produces a better effect, but may also reduce the contrast ratio.
Compensates the visual color difference with other monitors.
If you prefer to get the color reproduction to be closer to the Picture Mode setting, set this function to OFF.
NOTE:
- When the selected PICTURE MODE is different from your computer’s ICC color profile, you may experience
inaccurate color reproduction.
- MultiProfiler software, developed by NEC Display Solutions, is highly recommended to provide extended color
management features such as ICC profile Emulation and Printer Emulation. The latest MultiProfiler software is
available on the NEC Display Solutions website.
English-30
SPECTRAVIEW ENGINE is set to “OFF”:
Select from five different picture modes, either via the OSD menu item PICTURE MODE or using the PICTURE MODE button
on the wireless remote control.
For DisplayPort1, DisplayPort2, OPTION*, HDMI1, HDMI2
STANDARD
sRGB
CINEMA
CUSTOM1
CUSTOM2
HIGHBRIGHT
For MP
STANDARD
CINEMA
CUSTOM1
CUSTOM2
HIGHBRIGHT
PRESET types
PRESET
HIGH BRIGHT
STANDARD
sRGB
PURPOSE
Highest brightness setting.
Standard setting.
The standard color space used for the Internet, Windows® operating systems and digital cameras. Recommended
setting for general color management.
CINEMA
CUSTOM
A setting that boosts dark tones; best suited for movies.
Custom setting.
*: This function depends on which option board you are using.
English-31
OSD (On-Screen-Display) Controls
NOTE:
Some functions may not be available depending on the model or optional equipment.
Input source
Main Menu Icons
MULTI-INPUT
OPTION
Main Menu Item
Sub Menu
PICTURE:
PICTUREMODE
PRESET
SVE-1SETTING
PROGRAMMABLE1
100%
PICTUREMODE
BRIGHTNESS
GAMMA
LUMINANCE
BLACK
5%
COLOR
GAMMA
CUSTOMVALUE
WHITE
sRGB
CONTRAST
SHARPNESS
UHDUPSCALING
ASPECT
---
6500K
WHITE(x, y)
RED(x, y)
GREEN(x, y)
BLUE(x, y)
COLORVISIONEMU
UNIFORMITY
METAMERISM
COLORCONTROL
R -
x:0.279 y:0.292
x:0.683 y:0.306
x:0.191 y:0.709
x:0.153 y:0.044
OFF
ADVANCED
ROTATION
SPECTRAVIEWENGINE
RESET
Adjustment Settings
OFF
ON/OFF
+
+
+
+
+
+
0
0
0
0
0
0
Y -
G -
C -
B -
M -
Goto Adjustment
Return
Close
Select
Key Guide
Press UP or DOWN
to navigate to a
sub-menu.
Press SET/POINT
ZOOM to select an
option.
Press UP or DOWN,
Press MENU or EXIT.
PLUS or MINUS to select
the function or setting to
be adjusted.
Remote Control
Press UP or DOWN to
navigate to a sub-menu.
Press INPUT to
select an option.
Press UP or DOWN, PLUS
or MINUS button to select.
Press EXIT
Control Panel
OSD screen
English-32
Setting
INPUT
DisplayPort1
DisplayPort2
HDMI1
Select input signal.
HDMI2
HDMI3
MP
Displays images or movies saved in microSD memory card or USB storage device. Please refer to the Media
OPTION*3
Select input signal.
PICTURE
PICTURE MODE
Select picture mode:
SpectraView Engine = OFF: [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1], [CUSTOM2].
SpectraView Engine = ON: [SVE-1 SETTINGS], [SVE-2 SETTINGS], [SVE-3 SETTINGS], [SVE-4 SETTINGS] or
NOTE: If WHITE is set to NATIVE when the SPECTRAVIEW is ON, WHITE is not functioning.
To be able to set the CUSTOM VALUE, please set CST at GAMMA.
BRIGHTNESS*1
BACKLIGHT
Adjusts the overall image and background brightness. Press + or - to adjust.
NOTE: When MODE1 or MODE2 is selected in ROOM LIGHT SENSING, this function cannot be changed.
BRIGHTNESS*2
GAMMA*1, *2, *5
NATIVE
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
Select a monitor gamma correction for best picture quality. Selection depends on the desired usage.
Gamma correction is handled by the LCD panel.
2.2
Typical monitor gamma for use with a computer.
2.4
Good for video (DVD, etc.)
S GAMMA
Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the image
(S-Curve).
DICOM SIM.
DICOM GSDF curve simulated for LCD type.
HDR-ST2084 (PQ)
HDR-HYBRID LOG
Gamma setting for HDR, typically for UHD disk media and streaming videos.
Gamma setting for HDR, typically for UHD broadcasting. System gamma can be adjusted.
PROGRAMMABLE1, 2, 3 A programmable gamma curve can be loaded using optional NEC software.
AUTO HDR SELECT GAMMA correction of HDR signal automatically changes to HDR-ST2084 (PQ) or HDR-HYBRID LOG.
HDMI input only
COLOR*2
COLOR
Adjusts the color depth of the screen. Press + or - to adjust.
COLOR
Adjusts the color temperature of the entire screen. A low color temperature will result in a reddish screen. A high
color temperature will make the screen bluish. If TEMPERATURE needs further adjustment, the individual R/G/B/
levels of the white point can be adjusted. To adjust the R/G/B levels, set CUSTOM as COLOR TEMP selection.
NOTE: Predefined 6500k is set as picture mode, a color temperature of 6500k is predefined so it cannot be
changed.
TEMPERATURE*1
When PROGRAMMABLE1, PROGRAMMABLE2 or PROGRAMMABLE3 is selected in GAMMA CORRECTION,
this function cannot be changed.
COLOR CONTROL
Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.
Adjusts the hue of the screen. Press + or - to adjust.
HUE*4
MP input only
CONTRAST*1, *2
SHARPNESS*1
Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.
Adjusts the crispness of the image. Press + or - to adjust.
Achieves high-definition effect.
UHD UPSCALING*1
*1: If SPECTRAVIEW ENGINE is ON, this function is grayed out.
*2: This function is not available when sRGB is selected at PICTURE MODE.
*3: When you select OPTION for signal input, this function depends on which option board you are using.
*4: This function is not available for still image by MP input.
*5: When you use HDR signal, SPECTRAVIEW ENGINE should be OFF.
English-33
ASPECT
Select the aspect ratio of the screen image.
NOTE: When the ASPECT is set to DYNAMIC, the image will be changed to FULL image before IMAGE FLIP,
then start IMAGE FLIP.
When the ASPECT is DYNAMIC or ZOOM, the image will be changed to FULL image before TILE MATRIX,
and then start TILE MATRIX. After TILE MATRIX, the ASPECT will be returned to the previous ASPECT or set
ASPECT during TILE MATRIX.
If SCREEN SAVER is set, the ASPECT setting automatically changes to FULL from what you set. Once SCREEN
SAVER is off the ASPECT setting will go back to the setting that you originally set.
This function is not available when MOTION in SCREEN SAVER is active.
When the ASPECT is set to DYNAMIC or ZOOM while TILE MATRIX is set to active, after releasing
TILE MATRIX, DYNAMIC or ZOOM will be active.
Zoom is also not available for an image with input resolution at 3840 x 2160 (60 Hz) and 4096 x 2160 (60 Hz).
NORMAL
Shows the aspect ratio as it is sent from the source.
Fills the entire screen.
FULL
WIDE
Expands a 16:9 letterbox signal to fill the entire screen.
DYNAMIC
Expands 4:3 pictures to fill the entire screen with non-linearity image. Part of the outside image area will be cut
off due to expansion.
1:1
Shows the image in a 1 by 1 Pixel format. (If the input resolution is higher than the recommended resolution,
the image will be scaled down to fit the screen.)
ZOOM
Expands/reduces the image.
NOTE: The areas of the expanded image that are outside of the active screen area are not shown. The reduced
image may have some image degradation.
ZOOM
HZOOM
Maintains the aspect ratio while zooming.
Horizontal zoom value.
Vertical zoom value.
VZOOM
H POS
Horizontal position.
V POS
Vertical position.
ADVANCED
Some video formats may require different scanning modes in order to best display the image.
OVER SCAN
HDMI1, HDMI2, HDMI3, MP, OPTION*1
inputs only
ON
Image size is larger than what can be displayed. The image edge will appear cropped.
Approximately 95% of the image will be shown on the screen.
OFF
Image size stays within the display area. The whole image is displayed on the screen.
NOTE: When you use a computer with HDMI out, please set “OFF”.
AUTO
Image size is set automatically.
NOTE: This function is not available if input signal is MP.
Selects the IP (Interlace to Progressive) conversion function.
NOTE: IMAGE FLIP is not available. When SUPER is selected in INPUT CHANGE and displayed, this function
cannot be changed.
DEINTERLACE
ON
Converts interlaced signals to progressive. This is the default setting.
OFF
Disables IP conversion. This setting is best suited for motion pictures but increases the risk of image retention.
TELECINE
Automatically senses the sources frame rate for optimal picture quality.
NOTE: Set DEINTERLACE to ON if TELECINE is AUTO.
HDMI1, HDMI2, HDMI3, MP inputs only
ADAPTIVE
Sets the level of adjustment for dynamic contrast.
If HIGH is set, the image is displayed clearly but it makes brightness unstable due to the wide gap of contrast
variation.
CONTRAST*2
HDMI1, HDMI2, HDMI3, MP inputs only
*1: This function depends on which option board you are using.
*2: If SPECTRAVIEW ENGINE is ON, this function is grayed out.
English-34
ROTATION
Shows the inverse image right-left, up-down or rotation.
Press + or - to select.
NOTE: This function is not available when MOTION in SCREEN SAVER is “ON”.
IMAGE FLIP
NOTE: When the ASPECT is set to DYNAMIC, the image will be changed to FULL image before ROTATE starts.
When selecting IMAGE FLIP (except for NONE), the following functions are disabled: MULTI PICTURE MODE,
TEXT TICKER, STILL, POINT ZOOM and TILE MATRIX.
When the input signal is interlaced, the image may be distorted.
NONE
Normal mode.
H FLIP
The image inverts right-left.
The image inverts up-down.
The image rotates 180 degrees.
V FLIP
180° ROTATE
OSD FLIP
Determines the OSD display direction.
If “ON” is selected, the OSD will be inverted depending on the image status.
SPECTRAVIEW ENGINE
RESET
Resets all “PICTURE” settings back to factory settings except for SPECTRAVIEW ENGINE and PICTURE
MODE.
AUDIO
VOLUME
BALANCE
BALANCE
Increase or decrease output volume level.
Select STEREO or MONO for the audio output.
If you select STEREO, adjust the L/R volume balance.
Press the + button to move the stereo sound image to right.
Press the - button to move the stereo sound image to left.
NOTE: BALANCE is not available if MONO is set at STEREO/MONO.
SURROUND
Artificial surround sound.
NOTE: LINE OUT is disabled when this function is set to “ON”.
EQUALIZER
TREBLE
Accentuate or reduce the high frequency range of audio signals.
Press the + button to increase TREBLE.
Press the - button to decrease TREBLE.
BASS
Accentuate or reduce the low frequency sound.
Press the + button to increase BASS.
Press the - button to decrease BASS.
AUDIO INPUT
Selects the audio input source: [HDMI1], [HDMI2], [HDMI3], [DisplayPort1], [DisplayPort2], [IN], [MP],
[OPTION]*1.
MULTI PICTURE AUDIO
Selects audio source.
NOTE: This function depends on MULTI PICTURE setting.
LINE OUT
Selecting VARIABLE enables control of the line out level with the VOLUME button.
AUDIO DELAY
AUDIO DELAY
DELAY TIME
RESET
Activate a delay time to output the audio signal. The DELAY TIME can be set between 0 and 100 milliseconds.
Set to ON to activate this function.
Resets all AUDIO options back to factory settings, except for VOLUME.
*1: This function depends on which option board you are using.
English-35
SCHEDULE
SCHEDULE SETTINGS
Creates a working schedule for the monitor.
Press the
, +, - buttons to navigate and change the schedule settings. Press the SET/ZOOM on the remote
or Input change buttons on the monitor to select settings.
NOTE: Please set DAY & TIME before configuring the SCHEDULE SETTINGS.
When the SCHEDULE SETTINGS window is closed, any schedules that you set are saved.
If schedules are set for the same time, higher SETTINGS numbers are given the priority.
If OFF TIMER is ON, SCHEDULE SETTINGS is not available.
When you select an invalid input signal or picture mode, it will display in red. While the SCHEDULE SETTINGS
SETTINGS
POWER
TIME
Set ON to activate the schedule. Maximum 30 schedules are set.
Setting for the monitor power. Please set ON or OFF for each schedule.
Set the schedule operation time. If there is no specific time for the schedule set [--].
INPUT
Set the input signal for the schedule. To keep the input signal that is active when the schedule starts set [--].
When you set INPUT, please select ON at POWER.
PIC. MODE
Set the picture mode for the schedule. To keep the picture mode that is active when the schedule starts set [--].
When you set PIC. MODE, please select ON at POWER.
Select one item from below (only one item is available).
DATE
Select this setting if the schedule is for one day schedule or irregular schedules.
Select this setting if the schedule is repeating every day.
EVERY DAY
EVERY WEEK
WEEKDAY
Select this setting if the schedule is repeating every week.
Select this setting if the schedule is on a weekday.
This item is set by the WEEKEND and the HOLIDAY settings. A day, which is not selected at WEEKEND and
HOLIDAY settings is set as a weekday.
WEEKEND
Select this setting if the schedule is on a weekend.
Schedule operates on the date that is set at WEEKEND SETTINGS.
HOLIDAY
SCHEDULE LIST
HOLIDAY SETTINGS
No.
Schedule operates on the date that is set at HOLIDAY SETTINGS.
List of working schedules. Displays up to 30 schedules.
Creates holiday schedule for the monitor.
YEAR
MONTH
DAY
Set YEAR and MONTH.
Select DAY or WEEK.
DAY: Set a day.
WEEK
WEEK: Set a week and the day of the week.
If you set [--] at MONTH or YEAR, every month or year of the day you select is set as a holiday.
END DAY
Set the end of holiday date. If you schedule beyond a year, please separate the schedule per year.
NOTE: If DAY is not set, END DAY is not available. If your holiday setting includes [--] for year or month, END
DAY is not available.
SET/DELETE
WEEKEND SETTING
WEEKEND
Sets or deletes a schedule.
Set the day of the week.
DATE & TIME
Sets the date, time, and daylight savings region. Date & time must be set in order for the “SCHEDULE” function
to operate.
NOTE: If the monitor’s main power has been turned off for two weeks, the DATE & TIME setting goes back to the
default setting and the clock function stops working.
YEAR
MONTH
DAY
Sets the year for the real-time clock.
Sets the month for the real-time clock.
Sets the day for the real-time clock.
Sets the time for the real-time clock.
TIME
CURRENT DATE TIME Shows the current date and time.
English-36
DAYLIGHT SAVING
Sets daylight savings on or off.
NOTE: Please set the TIME & DATE setting first if you change the DAYLIGHT SAVING setting.
DAYLIGHT SAVING
BEGIN MONTH
END MONTH
If ON is selected, please set daylight savings settings below.
Set daylight savings beginning date.
Set daylight savings ending date.
TIME DIFFERENCE
OFF TIMER
Set the time difference.
Set the monitor to power off after a preset time period. A time period between 1 to 24 hours may be set.
NOTE: SCHEDULE is not available if OFF TIMER is ON.
RESET
Resets the following settings within the SCHEDULE menu back to factory setting: DATE & TIME and DAYLIGHT
SAVING.
MULTI INPUT
KEEP MULTI PICTURE
MODE*1
Allows the monitor to remain in MULTI PICTURE and TEXT TICKER mode after powering off.
When Power is returned, MULTI PICTURE and TEXT TICKER appear without having to enter the OSD.
MULTI PICTURE MODE*1, *3 Selects picture number and display form.
MULTI PICTURE
When “OFF” is selected, one picture is displayed.
When “ON” is selected, several pictures are displayed. Select PIP or PBP.
NOTE: When “ON” is selected, TEXT TICKER, TILE MATRIX, MOTION in SCREEN SAVER, IMAGE FLIP except
for NONE, SUPER in INPUT CHANGE is released.
PICTURE NUMBER
Selects [2 PICTURES], [3 PICTURES], [4 PICTURES].
After selected PICTURE NUMBER, select display form PIP, PBP1, PBP2, or PBP3. Depending on the setting at
PICTURE NUMBER, display form selection is changed.
PICTURE NUMBER: 2 PICTURES
PIP
PBP1
A
A
B
B
PICTURE NUMBER: 3 PICTURES
PIP
PBP1
PBP2
PBP3
A
A
B
A
B
C
A
B
B
C
C
C
PICTURE NUMBER: 4 PICTURES
A
B
A: PICTURE 1 B: PICTURE 2
C: PICTURE 3 D: PICTURE 4
C
D
ACTIVE PICTURE*1, *2
ACTIVE
When MULTI PICTURE is “OFF”, [PICTURE 1] is the Active Picture. When MULTI PICTURE is “ON”, sets Active
Picture.
NOTE: This function depends on MULTI PICTURE setting.
ACTIVE FRAME
The active picture is shown within a red frame.
INPUT SELECT*1, *2, *3
Selects the Multi Picture input. Press the + button or - button to select the input.
NOTE: This function is not available when MULTI PICTURE is “OFF”.
When changing input signal for the active picture, after selecting an input press SET.
PICTURE SIZE*1, *2, *4
Sets the Active Picture size.
Press the SET/POINT ZOOM button to adjust the picture size. Press + or CH+ to expand. Press - or CH- to reduce.
NOTE: This function is not available when MULTI PICTURE is set to 4 PICTURES PBP.
Depends on the setting at MULTI PICTURE MODE, some pictures cannot change their size.
PICTURE POSITION*1, *2, *4 Sets the Active Picture location.
Pressing the + button moves the Active Picture to the right, and pressing the - button moves it to the left.
Pressing the button moves the Active Picture up, and pressing the button moves it down.
ROTATE
When “ON” is selected, all pictures rotate.
When “OFF” is selected, sets each picture ROTATE settings.
NOTE: When TEXT TICKER, IMAGE FLIP except for NONE, STILL is ON or SCREEN SAVER is active,
this function is not available. If ASPECT “1:1” is selected, characters and lines may be displayed in blurring,
depending on the signal resolution.
When ROTATE is ON, POINT ZOOM and IMAGE FLIP except for NONE are not available.
Each picture ROTATE settings are released when MULTI PICTURE is set to “OFF”.
When input signal is Interlace, the image may be distorted.
When HDMI of the TERMINAL SETTINGS is set to MODE2, or [3 PICTURES] or [4 PICTURES] is selected at
PICTURE NUMBER in MULTI PICTURE MODE, ROTATE is not available.
If ROTATE of MULTI PICTURE CONTROL is selected in the input signal with a high refresh rate, the image may
not be displayed smoothly. To reduce this condition please set the input signal with a low refresh rate.
PICTURE ASPECT*1, *2, *4
Selects the Active Picture frame aspect.
*1: This function is released when selecting SUPER in INPUT CHANGE, MOTION in SCREEN SAVER, TILE MATRIX and IMAGE FLIP except for NONE.
*2: When TEXT TICKER is active or multi picture is OFF, this function is not available.
*3: When you select OPTION for multi picture input, this function depends on which option board you are using.
*4: This function is not available if PIP is set at MULTI PICTURE MODE and then PICTURE1 is set at ACTIVE PICTURE.
English-37
TEXT TICKER*1, *2
NOTE: When TEXT TICKER is set, MULTI PICTURE MODE and STILL are not available.
TEXT TICKER is released if following menu is activated: MULTI PICTURE MODE, TILE MATRIX, SCREEN
SAVER, IMAGE FLIP, SUPER in INPUT CHANGE.
When this function is active, POINT ZOOM and STILL are not available.
MODE
Enables Text Ticker and allows you to set Horizontal or Vertical direction.
Selects the location of the Text Ticker on the screen.
POSITION
SIZE
Determines the size of the Text Ticker in relationship to the overall screen size.
Enables auto-detection of the Text Ticker.
DETECT
INPUT SELECT
INPUT DETECT*4
Set input signal for PICTURE1, PICTURE2.
Selects the method of input detection the monitor uses when more than one signal source is connected.
NOTE: When SUPER is selected within INPUT CHANGE, this function cannot be changed.
INPUT DETECT is released if HUMAN SENSOR is activated while INPUT DETECT is active.
NONE
The Monitor will not search for signals at the other video input ports.
FIRST DETECT*2, *3
When the current video input signal is not present, the monitor searches for a video signal from another video
input port. If a video signal is present in the other input, the monitor switches from the current video source to this
active video source automatically.
The monitor will not look for any other video signals while the current video source is present.
LAST DETECT*2, *3
CUSTOM DETECT*2
When the monitor is reproducing a signal from the current video source and a new second video source is
supplied to the monitor, the monitor will automatically switch to the new video source. When the current video
input signal is not present anymore, the monitor searches for a video signal from any other video input. If a video
signal is present in the other input, the monitor switches from the current video source to this active video source
automatically.
Sets the priority of input signals.
When CUSTOM DETECT is selected, the monitor searches on preset inputs only.
NOTE: Priority of an option input signal is only available in PRIORITY3, except for a slot 2 type PC option.
If you set DisplayPort1 to Priority 1 or 2 or 3, you cannot set OPTION (slot 2 type PC option (DP)) to any priority
settings. If you set OPTION (slot 2 type PC option (DP)) to Priority 1 or 2 or 3, you cannot set DisplayPort1 to any
priority settings.
INPUT CHANGE
Sets input change speed. If “QUICK” is set, speed of changing input is faster but this setting may cause image
noise while switching signals.
Selecting SUPER enables high-speed switching between two preset signals.
NOTE: Depending on the option board you use, SUPER may not be available.
When “SUPER” is active, MULTI PICTURE MODE, TEXT TICKER, STILL, POINT ZOOM are not available.
TERMINAL SETTINGS
DisplayPort
Selects the DisplayPort mode [1.1a] or [1.2].
DisplayPort 1.1a is selected, SST is set automatically.
DisplayPort 1.2 is selected, set SST or MST.
DisplayPort 1.2 should be selected when using Multi-Stream Transport. Multi-Stream Transport requires a
corresponding display card. Contact your supplier for limitations of this function.
NOTE: MST is not available with DisplayPort IN2 signal input.
BIT RATE
HDMI
DisplayPort 1.1a is selected at DisplayPort, HBR is set automatically.
DisplayPort1.2 and SST are selected at DisplayPort, set HBR or HBR2.
DisplayPort1.2 and MST are selected at DisplayPort, HBR2 is set automatically.
Selects MODE1 or MODE2.
MODE1: Max resolution is 4096 x 2160 (30 Hz)
MODE2: Max resolution is 4096 x 2160 (60 Hz)
VIDEO LEVEL
RAW: For computer settings. Show all input signals of 0-255 gray levels.
EXPAND: For audio-visual equipment settings. Expands the input signals from 16-235 gray levels to 0-255 gray
levels.
AUTO: Automatically sets input signals by adjusting connected equipment.
NOTE: This function is available only in HDMI or DisplayPort or OPTION and is selected at INPUT SIGNAL.
SIGNAL FORMAT
RESET
Selects the color space setting for the HDMI/DisplayPort signal. If SLOT2 CH SETTING is 2CH, this function is
grayed out.
Resets MULTI INPUT options back to factory settings, except for INPUT DETECT (priority of input signals only),
INPUT CHANGE (INPUT1 and INPUT2), INPUT SELECT, PICTURE ASPECT and BIT RATE.
*1: This function is released when selecting SUPER in INPUT CHANGE, MOTION in SCREEN SAVER, TILE MATRIX and IMAGE FLIP except for NONE.
*2: When you select OPTION for multi picture input, this function depends on which option board you are using.
*3: Except for MP.
*4: Depending on the device, it may not be detected correctly.
English-38
OSD
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
SVENSKA
РУССКИЙ
Select the language used by the OSD.
OSD TIME
OSD POSITION
UP
Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.
Determines the location where the OSD appears on the screen.
DOWN
RIGHT
LEFT
INFORMATION OSD
Selects whether the Information OSD is displayed or not. The Information OSD will appear when the input signal
or input source changes. The Information OSD will also give a warning when no signal is detected or the signal is
out of range.
An interval between 3 to 10 seconds is selectable for the Information OSD to appear.
COMMUNICATION
INFO.
The MONITOR ID and IP ADDRESS will appear when the remote control Display button is pressed.
OSD TRANSPARENCY
OSD ROTATION
LANDSCAPE
Selects the transparency of the OSD.
Determines the OSD orientation between landscape and portrait.
Shows the OSD in landscape orientation.
Shows the OSD in portrait orientation.
PORTRAIT
KEY GUIDE
Key guide is shown when the OSD menu is displayed.
NOTE: This function is not available when OSD FLIP is “ON”.
MEMO
INPUT NAME
You can create a name for the INPUT currently being used.
Max: 14 characters, including Space, A-Z, 0-9, and some symbols.
RESET
Resets the following settings within the OSD menu back to factory setting:
OSD TIME, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY.
MULTI DISPLAY
AUTO TILE MATRIX
SETUP
TILE MATRIX allows one image to be displayed over multiple screens (up to 100) through a distribution amplifier.
Allows auto setting of TILE MATRIX by inputting the number of monitors arranged horizontally and vertically on
the primary monitor. Following settings are set automatically: MONITOR ID, TILE MATRIX, TILE MATRIX MEM,
Input Signal, VIDEO OUT SETTING, DisplayPort in TERMINAL SETTINGS.
NOTE: AUTO ID will be automatically executed. When you use this function, it is recommended that monitors be
chained by DisplayPort cable. This function is released if MOTION in SCREEN SAVER is activated.
Example of installation via LAN:
Primary monitor
H MONITORS
V MONITORS
3
3
SETTING COPY
In a daisy chain scenario, select the OSD menu categories that you want to copy over to the other monitors.
NOTE: When you use this function, monitors should be daisy chained by LAN cables. This function will be reset
to default when power is off. This function has a limit in the number of connected monitors, depending on type
and quality of the LAN cable you use.
COPY START
ALL INPUT
Select “YES” and press the SET button to start copying.
All input terminals settings are copied when you select this item. Default is off.
English-39
TILE MATRIX
Allows one image to be expanded and displayed over multiple screens (up to 100) through a distribution
amplifier.
NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate without a
distribution amplifier at a lower number of screens.
This function is released when selecting SCREEN SAVER or IMAGE FLIP except for NONE.
Dynamic and Zoom will not work when Tile Matrix is activated.
When “DYNAMIC” or “ZOOM” is selected in ASPECT while executing TILE MATRIX, the setting will be applied
after completing the TILE MATRIX.
When TILE MATRIX is active the following functions are not available: MULTI PICTURE MODE, TEXT TICKER,
If Media Player contents are played while TILE MATRIX is active, the image play timing might have a gap within
monitors.
This function is not available when SCREEN SAVER is active.
When HDMI of the TERMINAL SETTINGS is set to MODE2, TILE MATRIX is not available.
H MONITORS
V MONITORS
POSITION
Number of monitors arranged horizontally.
Number of monitors arranged vertically.
Select which section of the tiled image to be displayed on the monitor.
TILE COMP
Turns the TILE COMP feature on. If YES is set to the TILE COMP, you can adjust a displayed image size and
position by pressing the + button or the - button on the remote control.
ENABLE
TILE MATRIX MEM
COMMON
Enables the Tile Matrix settings.
When “INPUT” is selected, the TILE MATRIX setting is applied to each signal input.
All settings in the TILE MATRIX are saved for all signal inputs.
All settings in the TILE MATRIX are saved for the selected signal input.
INPUT
ID CONTROL
Sets the monitor ID number from 1-100 and group ID from A-J. DETECTED MONITORS shows the number of all
monitors that are included in the daisy chain of connected LAN cables.
NOTE: Do not turn off the monitors’ main power switch or put it into standby while AUTO ID/IP SETTING or
AUTO ID/IP RESET is activating.
The Group ID is made of multiple selections.
AUTO ID/IP SETTING
When “SET” is selected, AUTO ID/IP SETTING window is shown.
Do not connect network devices between the monitors connected with LAN.
SETTING ITEM
MONITOR ID
IP ADDRESS
Select an item from [MONITOR ID], [IP ADDRESS] and [ID and IP].
When “YES” is selected the monitor ID numbers are set automatically for all monitors.
Set the first octet to the third octet at “BASE ADDRESS”.
The fourth octet is automatically set from “1” and counting up to the number of monitors connected with LAN.
“BASE ADDRESS” is shown when “IP ADDRESS” or “ID and IP” is selected at SETTING ITEM.
ID and IP
Set “MONITOR ID” and “IP ADDRESS”.
BASE NUMBER
Set base number within 100 for the master monitor.
The other monitors that follow in the LAN chain will be given an individual monitor ID automatically. The monitor
ID given to each monitor counts up based on the base number of the master monitor. The monitor ID range is
1 to 100. Please choose a starting number that is low enough to include all connected monitors.
BASE ADDRESS
When “YES” is set, the monitor IP ADDRESS is set automatically for all monitors.
When “YES” is set, all settings in the AUTO ID/IP SETTING are activated.
ID/IP SETTING
START
DETECTED
MONITORS
This item is shown after “SETTING ITEM” is selected and “ID/IP ADDRESS START” is set to “YES”.
If the detected number of monitors and the actual number of MONITOR IDs assigned are different, select
“RETRY” to recount the monitors.
If the shown number is correct, set “CONTINUE”.
AUTO ID/IP RESET
RESET ITEM
When “RESET” is selected, AUTO ID/IP RESET window is shown.
Select a setting from [MONITOR ID], [IP ADDRESS], and [ID and IP].
When the number of monitors connected with LAN is changed, please select the same item that you selected at
“SETTING ITEM” in the AUTO ID/IP SETTING and then run the “AUTO ID/IP RESET”.
ID/IP RESET START When “YES” is set, the setting of selected item at RESET ITEM returns to default setting.
When the setting returns to default setting, “FINISH!!” is displayed.
NOTE: After “ID/IP RESET START” is activated, the individual settings for “MONITOR ID” and “IP ADDRESS” will
be reset even though the monitor’s are connected with LAN.
DETECTED
Displays the number of detected monitors.
MONITORS
COMMAND
TRANSFER
When “ON” is set, a command is sent to all monitors connected with LAN cables.
Resets all settings within the MULTI DISPLAY menu back to the factory setting.
RESET
English-40
DISPLAY PROTECTION
POWER SAVE
Set ENABLE or DISABLE. If you set it to ENABLE, set how long the monitor waits to go into power save mode
NOTE: The display card might not stop sending the digital data even though the image might have disappeared.
If this occurs the monitor will not switch into power management mode. POWER SAVE is disabled when AUTO
OFF or CUSTOM is selected in HUMAN SENSING*3.
AUTO POWER SAVE
TIME SETTING
Set the time when the monitor goes into auto power save mode after signal is lost.
POWER SAVE MESSAGE When the monitor goes into power save mode, a message is displayed when ON is selected.
FAN CONTROL
Cooling fans will reduce the internal temperature of the monitor to protect it from overheating.
If AUTO is selected, you can adjust the start temperature of the cooling fans and the fan speed.
HEAT STATUS
Shows the actual status of the fans, backlight and temperature sensors.
SCREEN SAVER
Use the SCREEN SAVER function to reduce the risk of Image Persistence.
NOTE: When the screen saver is activated, the image will be changed to FULL image. After the screen saver
stops, the image will be reproduced again with the current ASPECT setting.
The screen saver cannot be selected for 3840 x 2160 (60 Hz) nor 4096 x 2160 (60 Hz) signal input.
When the SCREEN SAVER is set to active, MULTI PICTURE MODE, STILL, IMAGE FLIP (except for NONE) or
TEXT TICKER, POINT ZOOM, TILE MATRIX are not available.
GAMMA*1
The monitor gamma is changed and fixed when “ON” is selected.
BACKLIGHT*1
The brightness of the backlight is decreased when “ON” is selected.
NOTE: Do not select this function when ROOM LIGHT SENSING is set to MODE1 or MODE2.
MOTION*2
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at user determined
intervals. You can set interval time and zoom ratio.
SIDE BORDER COLOR
Adjusts the color of the side borders when a 4:3 image is reproduced.
By pressing the + button on the remote control, the side borders will become brighter.
By pressing the - button, the side borders will become darker.
Background color of the Media Player window is also changed.
POWER ON DELAY
DELAY TIME
Adjusts the delay time between being in “standby” mode and entering “power on” mode.
“POWER ON DELAY” can be set between 0 and 50 seconds.
LINK TO ID
When “ON” is selected, the delay time is linked with the Monitor ID. It takes more time when there are a large
number of IDs.
ALERT MAIL
RESET
Resets all settings within the DISPLAY PROTECTION menu back to factory setting except for POWER ON
DELAY.
CONTROL
NETWORK INFORMATION Shows the current network settings.
LAN NOTE: When changing any LAN settings, you need to wait several seconds until modified LAN settings are
applied.
IP SETTING
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to enter a fixed IP address and subnet mask data obtained from your network
administrator.
NOTE: Consult your network administrator for the IP address when AUTO is selected for [IP SETTING].
IP ADDRESS
Set your IP address for the monitor connected to the network when MANUAL is selected for [IP SETTING].
SUBNET MASK
Set your subnet mask data for the monitor connected to the network when MANUAL is selected for
[IP SETTING].
DEFAULT GATEWAY
DNS
Set your default gateway for the monitor connected to the network when MANUAL is selected for [IP SETTING].
NOTE: Enter [0.0.0.0] to delete the setting.
Set the IP addresses of DNS servers.
AUTO: The DNS server, which is connected with the monitor, will automatically assign its IP address.
MANUAL: Manually enter the IP address of the DNS server which is connected with the monitor.
DNS PRIMARY
Enter the primary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
DNS SECONDARY
Enter the secondary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
*1: If SPECTRAVIEW ENGINE is ON, this function is grayed out.
*2: When you select OPTION for signal input, this function depends on which option board you are using.
*3: The function is available only when connecting the optional control unit.
English-41
CHANGE PASSWORD
Allows the security password to be changed.
The factory preset password is 0000.
SECURITY
PASSWORD
SECURE MODE
OFF
Input security password.
The security password is not required when the monitor power is on.
START-UP LOCK
CONTROL LOCK
BOTH LOCK
The security password is required when the monitor power is on.
The security password is required when a remote control button or a control button on the monitor is pressed.
The security password is required when either the monitor is powered on, or a remote control button or a control
button on the monitor is pressed.
IR LOCK SETTINGS
Prevents the monitor from being controlled by the wireless remote control.
When ACTIVATE is selected, all settings are activated.
NOTE: IR LOCK SETTINGS is a function intended only for the wireless remote control buttons. This function
does not lock out access to the buttons on the monitor. To return to normal operation, press the “DISPLAY” button
on the remote control and hold it down for more than 5 seconds.
MODE SELECT
UNLOCK
Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.
All buttons on the remote control are available for normal operation.
Locks all remote control buttons.
ALL LOCK
CUSTOM LOCK
Selects which buttons to be locked from POWER, VOLUME, and INPUT button.
Except for CUSTOM LOCK settings, other buttons on the remote control are locked.
POWER: When LOCK is selected, the POWER button is locked.
VOLUME: When UNLOCK is selected, set the minimum and maximum volume between VOL.0 to VOL.100.
VOLUME (+) button and VOLUME (-) buttons are only available from the minimum volume to the
maximum volume you set.
When LOCK is selected, VOLUME (+) button and VOLUME (-) buttons are locked.
INPUT:
When UNLOCK is selected, choose up to three buttons from DisplayPort1, DisplayPort2, HDMI1,
HDMI2, HDMI3, MEDIA PLAYER, OPTION which you prefer to be unlocked.
The unselected buttons are locked. When LOCK is selected, all INPUT buttons are locked.
CHANNEL: To lock channel buttons on the remote control, select it to LOCK then press ACTIVE, channel
CH/ZOOM (+) button and (-) button are locked.
KEY LOCK SETTINGS
Prevents the monitor from being controlled by the buttons on the monitor.
When ACTIVATE is selected all of the settings are activated.
NOTE: KEY LOCK SETTINGS is a function intended only for the buttons of the monitor. This function does not
lock out access to all buttons on the remote control. To activate the control key lock function, press the UP button
(
) and the DOWN button ( ) and hold down simultaneously for more than 3 seconds. To resume user mode,
press the UP button ( ) and the DOWN button ( ) and hold simultaneously for more than 3 seconds.
Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.
All buttons are available for normal operations.
MODE SELECT
UNLOCK
ALL LOCK
Locks all remote control buttons.
CUSTOM LOCK
Selects which buttons to be locked from POWER, VOLUME, and INPUT button.
Except for CUSTOM LOCK settings, other buttons on the remote control are locked.
POWER: When LOCK is selected, the POWER button is locked.
VOLUME: When UNLOCK is selected, set the minimum and maximum volume between VOL.0 to VOL.100.
The PLUS button (+) and the MINUS button (-) are only available from the minimum volume to the
maximum volume you set.
When LOCK is selected, the PLUS button (+) and the MINUS button (-) are locked.
INPUT:
When UNLOCK is selected, the INPUT/SET button is unlocked.
CHANNEL: To lock channel buttons on the remote control, select it to LOCK then press ACTIVE,
the UP button ( ) and the DOWN button ( ) are locked.
DDC/CI
ENABLE/DISABLE: Turns ON or OFF the two-way communication and control of the monitor.
DisplayPort2 input only
PING
Confirm successful connection with the network by communicating with a preset IP address.
Sets an IP ADDRESS for sending PING.
IP ADDRESS
EXECUTE
Checks a reply can be sent to the monitor or not from the IP ADDRESS by sending PING.
Resets IP ADDRESS SETTINGS back to factory settings.
IP ADDRESS RESET
English-42
AUTO DIMMING*1
Adjusts the backlight of the LCD automatically depending on the amount of ambient light.
AUTO BRIGHTNESS
DisplayPort1, DisplayPort2, MP, OPTION*3
inputs only
Adjusts the brightness level according to the input signal.
NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.
ROOM LIGHT
SENSING
The backlight of the LCD screen can be set to increase or decrease depending on the amount of ambient light
within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the
monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to
the eye in a variety of lighting conditions.
NOTE: When ROOM LIGHT SENSING is set, BACKLIGHT, AUTO BRIGHTNESS and BACKLIGHT in SCREEN
SAVER functions are disabled.
Do not cover the room light sensing sensor when you use MODE1 or MODE2.
AMBIENT parameter setting
ROOM LIGHT SENSING in OSD, select MODE1 or MODE2 and set MAX LIMIT, IN BRIGHT and IN DARK in
each mode.
MAX LIMIT: This is the max level of backlight, which you set.
IN BRIGHT: This is the backlight level that the monitor will go up to when the ambient light level is highest.
IN DARK: This is the level of backlight that the monitor will go down to when the ambient light level is low.
When the ROOM LIGHT SENSING is enabled the Backlight level of the screen changes automatically according
to the lighting conditions of the room (see figure below).
Factory Setting
BACKLIGHT range
BACKLIGHT range when
set to MAX LIMIT.
BACKLIGHT level set for
the monitor to use when
ambient lighting level is
low.
BACKLIGHT level set
for the monitor to use
when ambient lighting
level is high.
IN DARK
dark
IN BRIGHT
room bright condition
bright
Screen Backlight value by MODE1
Screen Backlight value by MODE2
MAX LIMIT: BACKLIGHT level is limited to your set level.
IN DARK: BACKLIGHT level set for the monitor to use when ambient lighting level is low.
IN BRIGHT: BACKLIGHT level set for the monitor to use when ambient lighting level is high.
BACKLIGHT
DIMMING*1
Automatically adjusts each of the clusters of the backlight of the LCD independently, according to the input signal.
HUMAN SENSING*2
HUMAN SENSING has three settings.
NOTE: POWER SAVE is disabled when AUTO OFF or CUSTOM is selected in HUMAN SENSING.
HUMAN SENSING is released if INPUT DETECT is set while HUMAN SENSING is active.
DISABLE
No human sensing.
AUTO OFF
At the preset time, when no person is detected, BACKLIGHT and VOLUME automatically go into OFF. When a
person comes near the monitor again, the monitor will automatically return to normal mode.
CUSTOM
BACKLIGHT and VOLUME automatically shift to the set value when detecting no person. When a person comes
near the monitor again, the monitor automatically returns to normal mode and reproduces the input signal
selected in INPUT SELECT.
POWER INDICATOR
POWER INDICATOR
Turns the LED on or off. If OFF is selected, the LED will not glow when the LCD monitor is in active mode.
SCHEDULE
INDICATOR
Turns the LED on or off depending on a schedule activity which is set at “SCHEDULE SETTINGS”. If OFF is
selected, the LED will not glow even if a schedule is in active mode.
INTELLI. WIRELESS DATA Select “ON” to activate INTELLIGENT WIRELESS DATA function (see page 61). A password is required when
using the function.
*1: If SPECTRAVIEW ENGINE is ON, this function is grayed out.
*2: The function is available only when connecting the optional sensor unit.
*3: When you select OPTION for signal input, this function depends on which option board you are using.
English-43
USB
TOUCH POWER
(Not available)
EXTERNAL CONTROL When ON is set, the monitor can be controlled by a device connected to USB2 port.
PC SOURCE
Select a device connected to USB1 which controls the monitor. If a control device is specific, select EXTERNAL
PC or OPTION.
OPTION is only available when slot 2 type PC option is connected to the monitor.
USB POWER
Selects a power relation of USB CM1 (2A).
Set ON to supply the power to the USB CM1 (2A).
NOTE: Power consumption depends on which USB devices are connected to the monitor.
CEC*
This function enables you to control the HDMI CEC compliant device connected via HDMI connector.
*: CEC is an abbreviation of Consumer Electronics Control.
CEC
When ON is set, please set items below.
NOTE: If ON is selected, the below functions are activated.
When the connected HDMI CEC device receives a play command, the monitor synchronously turns on then
changes the input signal to HDMI. If the monitor has been turned on, when a connected HDMI CEC device
receives a play command, input signal is switched to HDMI.
The connected HDMI CEC devices are controlled by the wireless remote control supplied with the monitor.
Depending on the connected device, the device may not work properly.
AUTO TURN OFF
AUDIO RECEIVER
When the monitor goes to standby via remote control or the power button on the monitor, a connected HDMI
CEC device go to standby synchronously.
NOTE: If the connected HDMI CEC device is recording, the device does not go into standby.
Activates HDMI CEC audio amplifier. If YES is set, outputs the sounds of the connected HDMI CEC device from
the connected HDMI CEC audio amplifier. If YES is set, the internal speaker or the external speaker connected to
the monitor is set to mute.
NOTE: When an HDMI CEC audio amplifier is connected, set to YES.
Please set to NO if there is no connected HDMI CEC audio device to the monitor.
SEARCH DEVICE
Searches the HDMI CEC device connected to the monitor. When search is successful, the connected HDMI CEC
device’s type and registered device name are shown. When search has been completed or failed, the SEARCH
DEVICE is set to NO automatically. To retry the SEARCH DEVICE, set it to YES again. After detecting HDMI
CEC devices, you can switch the device input by selecting the device.
RESET
Resets all the settings within the CONTROL menu back to factory setting except for LAN, CHANGE
PASSWORD, SECURITY, PING and INTELLI. WIRELESS DATA.
OPTION
OPTION POWER
Allows the monitor to supply power to an Option board slot during power save mode or standby mode.
AUTO: Power supply depends on whether or not an option board is connected.
ON: Supply power to the connected option continues during power save mode or standby mode.
OFF: Supply power to the connected option stops during power save mode or standby mode.
NOTE: To activate Power management function with no signal input from the inserted slot 2 type option, please
set OPTION POWER to AUTO or ON.
AUDIO*1
Selects the sound input signal according to the slot2 type option specifications. To activate DIGITAL, select
OPTION for input signal and OPTION for AUDIO INPUT.
NOTE: DIGITAL is activated only when OPTION is selected for input signal and OPTION for AUDIO INPUT.
INTERNAL PC*1
The function is available for a slot 2 type PC.
OFF WARNING
(Not adjustable)
AUTO OFF
Monitor power is automatically OFF when the internal PC is OFF or the monitor is in power save mode.
NOTE: If you select OFF, the monitor power is not automatically ON when the internal PC is ON.
START UP PC
FORCE QUIT
When ON is selected, the internal PC will start.
When ON is selected, a forced shutdown of the internal PC will be carried out.
Please use this function only when the operating system cannot be shut down manually.
*1: This function depends on which option board you are using. When changing the setting, turn the monitor’s main power switch off and on again.
English-44
SLOT2 CH SETTING
Selects signal type according to the slot 2 type option specifications.
Sets the signal type automatically.
AUTO
1CH
Fills the screen entirely with the signal which is selected in SLOT2 CH SELECT.
2CH
The DisplayPort signal is displayed on the left half of the screen, the TMDS signal is displayed on the right
half. If the internal PC does not support either one of the signal types, the existing signal will automatically be
displayed on the full screen.
SLOT2 CH SELECT
DisplayPort
TMDS
This function is available only when SLOT2 CH SETTING is 1CH.
Shows the DisplayPort signal from a slot 2 type PC option on the full screen.
Shows the TMDS signal from a slot 2 type PC option on the full screen.
Resets the AUDIO setting back to the factory setting within the OPTION menu.
RESET
SYSTEM
MONITOR INFORMATION Shows the model name, serial number and firmware version of your monitor.
CARBON SAVINGS: Display the estimated carbon saving information in kg-CO2. The carbon footprint factor in
the carbon saving calculation is based on the OECD (2008 Edition).
CARBON USAGE: Display the estimated carbon usage information in kg-CO2. This is the arithmetic estimation,
not actual measurement value. This estimation is based without any options.
FIRMWARE
Displays firmware version that is installed to the monitor.
Displays the MAC ADDRESS.
MAC ADDRESS
FACTORY RESET
All items are returned to factory shipment state.
NOTE: You can reset all items in all daisy chained monitors. Please be careful to avoid resetting all items
inadvertently.
Default values can be provided on request.
English-45
NOTE 1: CREATING A SCHEDULE
The schedule function allows the monitor to be set to power on or to be on standby at different times. Up to seven different schedules can be
programmed.
To program the schedule:
1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET/POINT ZOOM or the + button
to enter the Settings menu. Highlight the desired schedule number and press SET/POINT ZOOM. The box next to the number will turn yellow.
The schedule can now be programmed.
2. Use the down button to highlight the POWER. Use the + and - buttons to set ON. To set power off schedule, set OFF.
3. Use the down button to highlight the TIME. Use the + and - buttons to set the time.
4. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight
PIC. MODE. Use the + and - buttons to choose the picture mode.
5. Use the down button to select DATE, EVERY DAY, EVERY WEEK, WEEKDAY,
WEEKEND or HOLIDAY. Push the SET/POINT ZOOM button on a menu, which is
suitable for the schedule. If the schedule is to be run on a specific day, choose DATE
and press the SET/POINT ZOOM button. If the schedule is to be run every day, choose
EVERY DAY and press the SET/POINT ZOOM button. The circle next to EVERY DAY
will turn yellow. If a weekly schedule is desired, choose the days of the week using the up
and down buttons and pressing SET/POINT ZOOM to select. Then highlight the EVERY
WEEK option and press SET/POINT ZOOM. Please set WEEKDAY, WEEKEND, or
HOLIDAY in the same manner.
DisplayPort1
MULTI-INPUT
OPTION
SCHEDULE:
(MON) OCT.26.2015 12:37
SETTINGS:
SCHEDULE SETTINGS
SCHEDULE LIST
HOLIDAY SETTINGS
WEEKEND SETTINGS
DATE & TIME
1
POWER:
TIME:
ON
04 : 03
INPUT:
DisplayPort1
STANDARD
DAYLIGHT SAVINGS
OFF TIMER
PIC. MODE:
RESET
DATE
YEAR:
MONTH:
DAY:
EVERY DAY
EVERY WEEK
MON
2016
JAN
01
The WEEKDAY, WEEKEND and HOLIDAY settings are available under the SCHEDULE
TUE
FRI
WED
SAT
THU
SUN
6. After a schedule is programmed, the remaining schedules can then be set. Press MENU
to leave the OSD or press EXIT to go back to the previous menu.
WEEKDAY
WEEKEND
HOLIDAY
Return
Close
Choose
Mark
NOTE: If schedules are overlapping, the schedule with the highest number will have
priority over the schedule with the lowest number. For example, schedule #7 will have
priority over schedule #1.
If a selected input or picture mode is not available now, the disabled input or picture mode is shown in red.
NOTE 2: IMAGE PERSISTENCE
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a long period of time should be avoided.
To alleviate image persistence, turn off the monitor’s main power or set it to standby for as long as the previous image was displayed. For
example, if an image was on the monitor for one hour and a residual image remains, the monitor’s main power should be turned off or set it to
standby for one hour to erase the image.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at
regular intervals whenever the screen is idle, or turn off the monitor’s main power or set it to standby when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.
For long life use as a Public Display
Image Sticking of LCD Panel
When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside the LCD and a
residual or “ghost” image of the previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when a fixed image is displayed for long period, ionic impurities inside the LCD are accumulated
along the displayed image and may be permanent. (Image Sticking)
Recommendations
To prevent Image Sticking, and for longer life usage of the monitor, the following is recommended.
•
•
Fixed image should not be reproduced for long period. Change still images after short intervals.
When not in use, please turn off the monitor via remote control, or use the Power Management function of the PC, or use the built-in Schedule
Functions.
• Lower environmental temperatures prolong the lifespan of the monitor.
When a protective surface (glass, acrylic) is installed over the monitor’s screen surface, the monitor’s screen surface is located in an
enclosure, or if the monitors are stacked, utilize the temperature sensors inside the monitor.
To reduce the internal temperature, use the Cooling Fans, Screen Saver, the Power Management function of the PC and Low Brightness.
•
Please use “Screen Saver Mode” of monitor.
English-46
Remote Control Functions
REMOTE CONTROL ID FUNCTION
Monitor ID:1
Monitor ID:2
Monitor ID:3
REMOTE CONTROL ID
The remote control can be used to control up to 100 individual MultiSync monitors using
what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode
works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync
monitors. For example, if there are many monitors being used in the same area, a remote
control in normal mode would send signals to every monitor at the same time (see
Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate one specific
monitor within the group (see Figure 2).
Remote works
Remote works
Remote works
Figure 1
Remote in
Normal mode or
the REMOTE ID
is set to 0
TO SET REMOTE CONTROL ID
While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to
input the Monitor ID (1-100) of the monitor to be controlled via remote. The remote can then
be used to operate the monitor having that specific Monitor ID number.
When 0 is selected or when the remote control is in normal mode, all monitors will be
operated.
Monitor ID:1
Monitor ID:2
Monitor ID:3
TO SET/RESET REMOTE CONTROL MODE
ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for
2 seconds.
Remote does
not work
Remote does
not work
Remote works
Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold
down for 2 seconds.
In order for this feature to work properly, the monitor must be assigned a unique Monitor ID
number. The Monitor ID number can be assigned under the MULTI DISPLAY menu in the
Figure 2
Remote set up
to use REMOTE
ID:3
Point the remote control towards the remote sensor of the desired monitor and press the
REMOTE ID SET button. The MONITOR ID number is shown on the screen when your
remote control is in ID mode.
Use the remote to control all monitors in range
1. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID
number “0”.
2. All monitors within range of the remote control will now respond to keypad press.
NOTE: When the REMOTE ID is set to “0”, pressing REMOTE ID SET will make all monitors, within range of the remote signal,
display their Monitor ID on screen. This way you can easily see what the monitor ID is if you want to control a single monitor,
as described below.
Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it.
1. Set the MONITOR ID number for the monitor (See page 40). The MONITOR ID number can range from 1-100.
This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors.
2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number
(1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the monitor to be controlled.
3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.
The MONITOR ID number is shown in red on the monitor.
If the REMOTE CONTROL ID is “0”, then all monitors in range will show their respective MONITOR ID number in red.
If the MONITOR ID number is shown in white on the monitor, the MONITOR ID number and the REMOTE CONTROL ID are not the same.
NOTE: The GROUP ID cannot be specified via the remote control.
English-47
Multiple Monitors Connection
You can control multiple monitors by using RS-232C, REMOTE IN or LAN daisy-chain connection.
NOTE:
Multiple monitors that are daisy-chained have a limit to the connectable monitors.
Please execute AUTO ID (see page 40) before manually specifying the ID number or control by the specified
ID number.
Main Monitor
Connector
Sub Monitors
Connector
IN
OUT
IN
OUT
RS-232C
REMOTE IN
LAN1
LAN2
LAN1
LAN2
Connection
LAN1
LAN1
LAN2
LAN2
Next monitor
LAN Cable
LAN Cable
English-48
Controlling the LCD monitor via RS-232C Remote Control
This LCD monitor can be controlled by connecting a personal computer with an RS-232C (reverse type) terminal.
Functions that can be controlled by a personal computer are:
•
•
•
Power ON or standby.
Switching between input signals.
Sound Mute ON or OFF.
Connection
LCD Monitor + computer.
•
•
Please turn off the monitor’s main power when connecting a computer to the monitor.
Please turn on the connecting computer first then turn on the monitor’s main power.
If you turn on the computer and monitor in reverse order, the com port may not work.
•
When controlling the monitor connected with an RS-232C cable, please refer to the Control command diagram (See page 57)
or see the “External_Control.pdf” file on the CD-ROM supplied with the monitor.
Computer
RS-232C
RS-232C Cable
NOTE:
If your computer is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact
your supplier for details.
To control a monitor, please use the control command. Instructions for the control command can be found on the CD included
with the monitor. The file is called “External_control.pdf”.
English-49
1) Interface
PROTOCOL
RS-232C
9600 [bps]
8 [bits]
BAUD RATE
DATA LENGTH
PARITY
NONE
STOP BIT
1 [bit]
FLOW CONTROL NONE
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
The reverse type cable (null modem cable) (not included) should be used for RS-232C control.
2) PIN ASSIGNMENT
RS-232C input/output
Pin No Name
1
2
3
4
5
6
7
8
9
NC
D-SUB 9P (Monitor side)
RXD
TXD
NC
5
1
6
GND
NC
9
NC
NC
NC
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
English-50
Controlling the LCD monitor via LAN Control
Connecting to a Network
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.
To use a LAN connection you are required to assign an IP address.
Example of LAN connection:
Server
NOTE: Use a category 5 or higher LAN cable.
Hub
LAN cable
(not supplied)
Network Setting by Using an HTTP Browser
Overview
Connecting the monitor to a network allows for monitor control from a computer via the network.
The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP
server. Please be sure to use “Microsoft Internet Explorer 10” or a higher version for the web browser.
(This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will
vary depending on the version of the browser. Please refer to the help files and the other information provided in your software.)
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the
monitor and entering the following URL as described below:
Network Setting
HINT:
The default IP address is assigned automatically to the monitor.
The exclusive application can be downloaded from our website.
NOTE:
If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to
refresh your web browser (or clear the cache).
If the monitor appears to be slow in response to commands or clicks on buttons in the browser, or the general speed
of operation is unacceptable, this may be due to network traffic or the settings on your network. Should this happen,
consult your network administrator.
The monitor may not respond if the buttons shown on the browser are repeatedly pressed in rapid intervals. Should
this happen, wait a moment and repeat. If you still can’t get a response, turn the monitor off and then back on.
English-51
Preparation Before Use
Connect the monitor to the network, using a commercially available LAN cable, before attempting to use browser operations.
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting
method. Although the type of proxy server will be a factor, it is possible that items that have been set will not be shown,
depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in operation. It is
recommended that a proxy server is not used unless the network environment requires it.
Handling of the Address for Operation via a Browser
A host name can be used in the following cases (corresponding to the IP address of the monitor):
The host name must be registered in the domain name server (DNS) by the network administrator. You can then access the
network settings of the monitor via this registered host name by using a compatible browser.
If the host name has been configured in the “HOSTS” file of the computer being used, you can then access the network settings
of the monitor via this host name by using a compatible browser.
Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by
Example 2: When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying
http://192.168.73.1/index.html for the address or the entry column of the URL.
Operation
Access the following address to show HOME.
Click each link on the left column below HOME.
REMOTE CONTROL
Enable an operation to control the monitor equivalent to the keys on the remote control.
OSD menu
Enable the operation to set the following OSD menu:
INPUT, PICTURE, AUDIO, SCHEDULE, MULTI INPUT, OSD, MULTI DISPLAY, DISPLAY PROTECTION, CONTROL, OPTION,
SYSTEM.
NOTE:
Function of buttons which are shown on setting pages.
[APPLY]: Save your settings.
[CANCEL]: Return to the previous settings. NOTE: CANCEL is disabled after clicking APPLY.
[RELOAD]: Reload the settings.
[RESET]: Resets to the initial setting.
English-52
Network Setting
Click on “NETWORK” on the left column below HOME.
IP SETTING
Select an option for setting the IP ADDRESS.
AUTO: Automatically assign an IP address.
MANUAL: Manually set an IP address for the monitor connected to the network.
NOTE: Consult your network administrator if you have any trouble.
IP ADDRESS
Set your IP address for the monitor connected to the network when [MANUAL] is selected for
[IP SETTING].
SUBNET MASK
Set your subnet mask data for the monitor connected to the network when [MANUAL] is selected for
[IP SETTING].
DEFAULT GATEWAY Set your default gateway for the monitor connected to the network when [MANUAL] is selected for
[IP SETTING].
NOTE: Set as [0.0.0.0] to delete the setting.
DNS
Set for IP ADDRESS setting of DNS server.
AUTO: The DNS server connected to the monitor will automatically assign its IP address.
MANUAL: Manually enter the IP address of the DNS server that is connected with the monitor.
PRIMARY DNS
Enter the primary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
SECONDARY DNS
Enter the secondary DNS server settings of the network connected with the monitor.
NOTE: Enter [0.0.0.0] to delete the setting.
NOTE:
The following settings will be set back to the factory settings when IP ADDRESS RESET is selected at CONTROL of
the OSD:
[IP SETTING]: AUTO, [IP ADDRESS]: 192.168.0.10, [SUBNET MASK]: 255.255.255.0, [DNS]: AUTO [DEFAULT
GATEWAY], [PRIMARY DNS] and [SECONDARY DNS] are blank.
English-53
Mail Setting
Click on “MAIL” on the left column below HOME.
This option notifies your computer about an error message via e-mail when using wired LAN. An error message will be sent
when an error occurs in the monitor.
ALERT MAIL
Selecting [ENABLE] will turn on the Alert Mail feature.
Selecting [DISABLE] will turn off the Alert Mail feature.
STATUS MESSAGE
Selecting [ENABLE] will turn on the STATUS MESSAGE feature.
Selecting [DISABLE] will turn off the STATUS MESSAGE feature.
SENDER’S ADDRESS
SMTP SERVER
Type in the sender’s address. Up to 60 alphanumeric and symbols characters can be used.
Type in the SMTP server name to be connected with the monitor.
Up to 60 alphanumeric characters can be used.
RECIPIENT’S
Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.
ADDRESS 1 TO 3
AUTHENTICATION
METHOD
This selects the authentication method of the email transmission.
POP3 SERVER
USER NAME
This specifies the address of the POP3 server that is used in the authentication of the email.
This sets the user name for logging into the authentication server when authentication is required
for the email transmission. Up to 60 alphanumeric characters can be used.
PASSWORD
This sets the password for logging into the authentication server when authentication is required for
the email transmission. Up to 60 alphanumeric characters can be used.
TEST MAIL
Click this button to send a test email to check if your settings are correct.
NOTE:
HINT:
• If you execute a test, you may not receive an Alert email.
Should this happen, check whether the network settings are correct.
• If you entered an incorrect address in a test, you may not receive an Alert email.
Should this happen, check that the Recipient’s Address is correct.
For the control command diagram, please see the file “External_Control.pdf” on the CD-ROM supplied with this
monitor.
Alert error message list
Error number
* ErrorCode
Alert mail Message
Explanation
Measure
The monitor’s power supply is not
functioning normally.
Standby power abnormal
Please contact your supplier.
70h ~ 7Fh
80h ~ Fh
The cooling fan has stopped.
Cooling fan abnormal
Backlight abnormal
Please contact your supplier.
Please contact your supplier.
The monitor’s backlight unit is not
functioning normally.
90h ~ 9Fh
A0h ~ AFh
The monitor is overheated.
Temperature abnormal
Please contact your supplier.
A Sensor reached the temperature limit
which was specified in the OSD.
Reconfirm the settings in the OSD
(DISPLAY PROTECTION-FAN
CONTROL) or please contact your
supplier.
A2h
*Condition: DISPLAY PROTECTION-FAN
CONTROL-COOLING FAN = AUTO
The monitor does not receive an input
signal.
No signal
Please check “No picture” in
“Troubleshooting”.
B0h ~ BFh
D0h
The remaining capacity of the error log The Proof of Play log memory size is
decreased.
Please get a log by using PD external
1 more hour.
The battery for clocks is empty.
The battery is empty.
Please connect the monitor to the
power then recharge the battery.
Please set (DATE & TIME) in OSD.
D1h
E0h ~ EFh
A system error occurred in the monitor. System error.
Please contact your supplier.
English-54
SNMP Settings
Click on “SNMP” on the left column below HOME.
The SNMP protocol is used to get status information and to control a monitor directly via the network.
Version:
SNMP v1 Authenticated plaintext by community name, does not return a confirmation message of the trap.
SNMP v2c Authenticated plaintext by community name, returns a confirmation message of the trap.
Community name:
The default setting of community name is “public”. It is read only. You can set community names for up to 3 settings.
Trap:
Sending error message to a specified address when an error occurs in the monitor.
Check Box
Temperature
Explanation
Temperature abnormal
Cooling fan abnormal
Power abnormal
Error code
0xA0, 0xA1, 0xA2
Fan
0x80, 0x81
Power
0x70, 0x71, 0x72, 0x78
Inverter/Backlight
No Signal
Inverter or backlight abnormal 0x90, 0x91
No signal
0xB0
0xD0
0xE0
PROOF OF PLAY
System Error
Lower the log storage
System error
AMX Settings
Click on “AMX” on the left column below HOME.
AMX BEACON
To turn on or off for the detection from AMX Device Discovery when connecting to a network
supported by an AMX’s NetLinx control system.
HINT:
When using a device that supports AMX Device Discovery, all AMX NetLinx control systems will
recognize the device and download the appropriate Device Discovery Module from an AMX server.
Selecting [ENABLE] AMX Device Discovery will detect the device.
Selecting [DISABLE] AMX Device Discovery will not detect the device.
CRESTRON Settings
Click on “CRESTRON” on the left column below HOME.
CRESTRON ROOMVIEW compatibility
The monitor supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and
controlled from a computer or a controller.
For further information visit http://www.crestron.com
ROOMVIEW
ROOMVIEW for managing from the computer.
ON: Enables ROOMVIEW.
OFF: Disables ROOMVIEW.
CRESTRON
CONTROL
CRESTRON CONTROL for managing from the controller.
ON: Enables CRESTRON CONTROL.
OFF: Disables CRESTRON CONTROL.
CONTROLLER IP
ADDRESS
Sets the IP address of the CRESTRON SERVER.
IP ID
Sets your CRESTRON SERVER IP ID.
HINT:
The CRESTRON settings are required only for use with CRESTRON ROOMVIEW.
For further information visit http://www.crestron.com
English-55
Name Settings
Click on “NAME” on the left column below HOME.
MONITOR NAME
Defines a monitor name. The name must be max. 16 characters long. The default is the model name.
HOST NAME
(CONTROL)
Type in the hostname of the monitor which is connected to the network.
Up to 15 alphanumeric characters can be used.
HOST NAME (MP)
Type in the hostname of the network to be used in the Media Player connected to the monitor.
Up to 15 alphanumeric characters can be used.
DOMAIN NAME
Type in the domain name of the network which is connected with the monitor.
Up to 60 alphanumeric characters can be used.
Network Password Settings
Click on “NETWORK PASSWORD” on the left column below HOME.
PJLink CLASS
Set a class for PJLink*.
NOTE: PJLink is a network interface standard that JBMIA established.
This monitor is available for class1 and class2 command.
NOTIFY FUNCTION Enable or disable a notification of the monitor network condition. This function is only for class2.
ENABLE
NOTIFY ADDRESS
Set an IP ADDRESS to which the monitor network status will be sent. This function is only for class2.
PJLink PASSWORD Set a password for PJLink*. The password must be max. 32 characters long. Do not forget your
password. If you forget your password, consult your supplier.
HTTP PASSWORD
Set a password for the HTTP server. The password must be max. 10 characters long.
HTTP PASSWORD
ENABLE
An HTTP PASSWORD is required when logging into the HTTP server.
Set the monitor name as the USER NAME when entering the password.
*What is PJLink?
PJLink is a standardization of protocol used for controlling devices of different manufacturers. This standard protocol was
established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005.
The device supports all commands of PJLink.
PD LIST Information
Click on “PD LIST” on the left column below HOME.
Shows a list of monitor IDs and IP addresses of multiple monitors which are daisy-chained.
NOTE: Only the master monitor can show the list.
MEMO Settings
Click on “MEMO” on the left column below HOME.
Set a title and message.
TITLE
The title must be max. 24 characters long.
MESSAGE
A message must be max. 240 characters long.
MEMO PASSWORD The default is “0000”.
MEMO PASSWORD A MEMO PASSWORD is required when selecting MEMO PASSWORD ENABLE.
ENABLE
SD-CARD VIEWER setting
Click “SD-CARD VIEWER” on the left side of HOME.
External Control
Connecting external device
There are two ways to connect an external device to the monitor.
• RS-232C terminal.
Connecting an external device to the RS-232C terminal of the monitor with a RS-232C cable.
• LAN port.
Connecting an external device to the LAN port of the monitor with a LAN cable.
For further information regarding the type of LAN cable to use, please consult your network administrator.
English-56
Connecting interface
RS-232C Interface
PROTOCOL
BAUD RATE
DATA LENGTH
PARITY
RS-232C
9600 [bps]
8 [bits]
NONE
STOP BIT
1 [bit]
FLOW CONTROL NONE
LAN interface
PROTOCOL
TCP
PORT NUMBER
7142
COMMUNICATION SPEED AUTO setting (10/100Mbps)
Control command diagram
For other commands, please see “External_Control.pdf” file on the CD-ROM supplied with the monitor.
Function (Monitor ID = 1)
Code Data
Power ON
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d
Power OFF
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 46 03 04 0d
Input Source Select DisplayPort1
Input Source Select DisplayPort2
Input Source Select HDMI1
Input Source Select HDMI2
Input Source Select HDMI3
Input Source Select MP
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 30 46 03 04 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 30 03 73 0d
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 31 30 03 73 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 31 03 72 0d
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 31 31 03 72 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 32 03 71 0d
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 31 32 03 71 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 38 32 03 78 0d
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 38 32 03 78 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 38 37 03 7D 0d
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 38 37 03 7D 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 44 03 06 0d
Input Source Select OPTION
or
01 30 41 30 45 30 41 02 31 31 30 36 30 30 30 44 03 06 0d
Sound Mute ON
Sound Mute OFF
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 31 03 09 0d
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 32 03 0a 0d
ASCII Control command
This monitor supports control command, which is listed in the “External_Control.pdf” file on the CD-ROM supplied with the
monitor, but also supports common ASCII control command, which is used for controlling the NEC monitor or projector from a
connected PC. For further information please visit our website.
Parameter
Input command
Status command
Input signal name
DisplayPort1
DisplayPort2
HDMI1
Response
DisplayPort1
DisplayPort2
hdmi1
Parameter
Response
error:temp
error:fan
Error status
DisplayPort1 or DisplayPort
Temperature abnormal
Cooling fan abnormal
Inverter or backlight abnormal
System error
DisplayPort2
hdmi1 or hdmi
hdmi2
error:light
error:system
HDMI2
hdmi2
HDMI3
hdmi3
hdmi3
MP
mp
mp
OPTION
option
option
English-57
Supporting HDMI CEC command
HDMI CEC command name
Explanation
OSD menu
Setting
CEC
One Touch Play
If HDMI CEC supporting devices are
turned on, the monitor connected to the
devices by HDMI cable is also turned
on automatically. After that, the input
switches to HDMI from an input, which
you selected.
(Consumer
Electronics
Control)
If the monitor is turned on when HDMI
CEC devices are turned on, it changes
the input from the original one to HDMI.
To set CEC menus please follow the steps
below.
Remote Control Pass
Through
The monitor’s wireless remote control
button operation is functioning to HDMI
CEC supporting devices.
By using
buttons select CONTROL >
CEC then press SET/POINT ZOOM button
on the CEC.
By using + - buttons select ON then press
SET/POINT ZOOM button on the ON.
For example, if turning on the monitor
by wireless remote control and pressing
the play button, HDMI CEC supporting
devices will also be turned on and play.
Power Status
Connected HDMI CEC supporting
devices obtains the monitor’s power
status, such as the monitor is in standby
mode or on.
System Information
This function obtains the information of a
connected HDMI CEC supported device
(CEC version, Physical Address). In
addition, this function copes with “Change
Language function”.
If the language for the monitor is
changed, the language for a connected
HDMI CEC supported device is changed
to the same language, which is selected
for the monitor.
For the “Change Language function”, it is
necessary that the connected HDMI CEC
supported device be able to cope with
multi-language.
AUTO
System Standby
If the monitor is set to standby using the
By using
buttons select AUTO TURN
TURN OFF
wireless remote control supplied with the OFF then press SET/POINT ZOOM.
monitor, HDMI CEC supported devices
also go into standby at the same time.
If the monitor goes into standby while
an HDMI CEC supported device is
recording, the device is kept on. Please
refer to the user’s manual supplied with
the HDMI CEC supported device for
further information.
By using + - buttons select YES then press
SET/POINT ZOOM button on the YES.
AUDIO
RECEIVER
System Audio Control
The function sends digital audio signal
through the HDMI cable. Please set an
HDMI CEC audio amplifier between the
monitor and an HDMI CEC supported
device with an HDMI cable.
The Volume button on the wireless
remote control supplied with the
monitor is also controlling the volume
of the connected HDMI CEC audio
amplifier.
By using
buttons select AUDIO
RECIEVER then press SET/POINT
ZOOM.
By using + - buttons select YES then press
SET/POINT ZOOM button on the YES.
While this function is active, the internal
speaker or external speaker connected to
the monitor is set to MUTE automatically.
SEARCH
DEVICE
Device OSD Name Transfer This function obtains the connected
HDMI CEC supported device’s name.
By using
buttons select SEARCH
DEVICE then press SET/POINT ZOOM.
Routing Control
By selecting a device name, the HDMI
CEC supported device input switches to
the input you selected. After selecting the
device, wireless remote control operation
is functioning for the selected device.
By using + - buttons select YES then press
SET/POINT ZOOM button on the YES.
This CEC function supports Feature Abort. We recommend that connecting this monitor to a device supporting HDMI CEC.
English-58
POINT ZOOM
Using the “SET/POINT ZOOM” button on the remote control enlarges part of the screen image.
Press the CH+/- button to zoom in or out. The image can be expanded up to 10 times.
1
2
3
4
5
6
Press the [SET/POINT ZOOM] button on the remote control. The icon looks like a magnifier.
Move the magnifier icon with the [ ] [ ] [+] [-] buttons.
Press the [CH+] to zoom in. Press [CH-] to zoom out.
Press the [SET/POINT ZOOM] to let the icon disappear.
Press the [EXIT] to return to the normal image size.
Press the [MENU] to open the OSD menu.
NOTE:
• When using this function, the image may look distorted.
• This function is not available when set to IMAGE FLIP (except for NONE), MULTI PICTURE MODE, SCREEN
SAVER, SUPER in INPUT CHANGE, TILE MATRIX and TEXT TICKER.
• When DYNAMIC or ZOOM is selected in ASPECT, the image will change to FULL. Then start with POINT ZOOM.
After exiting POINT ZOOM, ASPECT will return to the previous ASPECT settings. When ASPECT is changed
during the POINT ZOOM operation, DYNAMIC and ZOOM will be set to FULL image.
• The magnifier icon does not move to a no image area.
• POINT ZOOM returns to the normal image size after changing the input signal or when the monitor is powered off.
• POINT ZOOM will become inactive when changing the ASPECT setting during the POINT ZOOM operation.
• When the POINT ZOOM is active, the STILL function is not available.
• POINT ZOOM is not available when MODE2 in HDMI in TERMINAL MODE and with a 3840 x 2160 (60 Hz)
DisplayPort signal.
English-59
PROOF OF PLAY
This function allows to sending of messages for the current status of the monitor by self-diagnosis.
Check item
INPUT
Message
DisplayPort1, DisplayPort2, HDMI1, HDMI2, HDMI3, OPTION*, MP
ex. (H)1920, (V)1080 , (H)1360, (V)768 or No signal or Invalid signal
IN, DisplayPort1, DisplayPort2, HDMI1, HDMI2, HDMI3, OPTION*, MP
Audio in or No Audio in or N/A (IN, OPTION (analog)*)
Normal Picture or No Picture
①
②
③
④
⑤
⑥
⑦
Resolution
AUDIO INPUT
Audio signal
Picture Image
AUDIO OUT
TIME
Normal Audio or No Audio
(year)/(month)/(day)/(hour)/(minutes)/(second)
00h: Normal Proof of Play event
01h: Proof of Play event is “last power on time”
10h: MEDIA PLAYER is stop
11h: MEDIA PLAYER is start
12h: MEDIA PLAYER is pause
13h: MEDIA PLAYER error occur
20h: Contents Copy from USB
h
EXPANSION DATA 21h: Contents Copy form network folder
30h: Contents Copy Success
31h: Contents Copy Error (No media)
32h: Contents Copy Error (Connect error)
33h: Contents Copy Error (Out of disk space)
34h: Contents Copy Error (Read/Write error)
40h: Human detected (Human sensor Status)
41h: Human detect cleared (Human Sensor Status)
*: This function depends on which option board you are using.
Example:
HDMI1
①
②
③
④
⑤
⑥
⑦
1920 x 1080
HDMI1
IN1
Normal Picture
Normal Audio
2014/1/1/0h/0m/0s
h 10h: MEDIA PLAYER is stop
NOTE: For the Proof of Play function, please see the “External_Control.pdf” on the CD-ROM supplied with this monitor.
English-60
INTELLIGENT WIRELESS DATA
This function allows getting the monitor status via wireless communication, even while the monitor’s main power is off or is not
yet installed.
Even some OSD items may be set by using this feature.
NOTE:
Please contact your supplier for detailed information.
Complied with ISO 15693.
Function name
Setting Copy
Setting read and write function
Display information
Security Setting
MULTIPICTURE matrix
PICTURE NUMBER: 2 PICTURES
PIP
PBP1
A
A
B
B
PICTURE NUMBER: 3 PICTURES
PIP
PBP1
PBP2
PBP3
A
A
B
A
B
C
A
B
B
C
C
C
PICTURE NUMBER: 4 PICTURES
A
B
A: PICTURE 1 B: PICTURE 2
C: PICTURE 3 D: PICTURE 4
C
D
PICTURE NUMBER: 2 PICTURES
Picture 2
HDMI1
HDMI2
HDMI3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
HDMI IN2
HDMI IN3
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
[
[
Yes
No
No
[
Yes
No
No
No
No
[
Yes
No
No
No
No
No
No
[
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
HDMI1
HDMI2
HDMI3
[
Yes
No
No
No
No
No
No
[
Yes
No
Yes
No
Yes
No
[
[
Yes
No
Yes
No
No
No
No
[
Yes
No
Yes
No
[
[
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
[
Yes
Yes
Yes
[
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
[
[
[
–
No
Option board slot
(SLOT2 (DP))
[
[
[
[
[
[
[
[
[
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
No
No
[
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
No
Yes
*: PBP1: Yes, PIP: No
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
English-61
PICTURE NUMBER: 3 PICTURES
PIP/PBP1/PBP2
PICTURE 1: HDMI1 (MODE1)
Picture 3
HDMI1
HDMI2
HDMI3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
HDMI IN2
HDMI IN3
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
Connector
HDMI IN1
HDMI IN2
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
No
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
No
No
Yes
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI2
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI3
MP
HDMI IN3
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
Yes
No
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PIP/PBP2
PICTURE 1: HDMI1 (MODE2), HDMI2 (MODE2), HDMI3 (MODE2)
Picture 3
DisplayPort2 DisplayPort1
HDMI1
HDMI2
HDMI3
MP
–
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
HDMI IN2
HDMI IN3
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
HDMI2
HDMI3
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
No
No
No
No
No
No
No
Yes
Yes
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
MP
–
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PIP/PBP1/PBP2
PICTURE 1: HDMI2 (MODE1)
Picture 3
HDMI1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
Connector
HDMI IN1
HDMI IN2
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
Yes
No
No
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI2
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI3
MP
HDMI IN3
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
Yes
No
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
English-62
PIP/PBP1/PBP2
PICTURE 1: HDMI3 (MODE1)
Picture 3
HDMI1
HDMI2
HDMI3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
HDMI IN2
HDMI IN3
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
Connector
HDMI IN1
HDMI IN2
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
Yes
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI2
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI3
MP
HDMI IN3
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
Yes
No
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PIP/PBP1/PBP2
PICTURE 1: MP
Picture 3
HDMI1
HDMI IN1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
Connector
HDMI IN1
HDMI IN2
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI2
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI3
MP
HDMI IN3
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
Yes
No
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PIP/PBP1/PBP2
PICTURE 1: DisplayPort2
Picture 3
HDMI1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
Connector
HDMI IN1
HDMI IN2
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI2
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI3
MP
HDMI IN3
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
Yes
No
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
English-63
PIP/PBP1/PBP2
PICTURE 1: DisplayPort1
Picture 3
HDMI1
HDMI2
HDMI3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
HDMI IN2
HDMI IN3
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
Connector
HDMI IN1
HDMI IN2
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI2
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI3
MP
HDMI IN3
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PIP/PBP1/PBP2
PICTURE 1: OPTION (DP)
Picture 3
HDMI1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
Connector
HDMI IN1
HDMI IN2
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI2
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI3
MP
HDMI IN3
–
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PIP/PBP2
PICTURE 1: OPTION (DP+TMDS)
Picture 3
HDMI1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
HDMI2
HDMI3
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
English-64
PIP/PBP2
PICTURE 1: OPTION (TMDS)
Picture 3
HDMI1
HDMI IN1
HDMI2
HDMI3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN2
HDMI IN3
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
HDMI2
HDMI3
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PBP1
PICTURE1: OPTION (TMDS)
Picture 3
HDMI1
HDMI IN1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
HDMI1
HDMI2
HDMI3
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PBP3
PICTURE 1: HDMI1 (MODE1)
Picture 3
HDMI1
HDMI IN1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
No
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
No
No
Yes
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
HDMI1
HDMI2
HDMI3
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
English-65
PBP3
PICTURE 1: HDMI2 (MODE1)
Picture 3
HDMI1
HDMI2
HDMI3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
HDMI IN2
HDMI IN3
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
Yes
No
No
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
HDMI1
HDMI2
HDMI3
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PBP3
PICTURE 1: HDMI3 (MODE1)
Picture 3
HDMI1
HDMI IN1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
Yes
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
HDMI1
HDMI2
HDMI3
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PBP3
PICTURE 1: MP
Picture 3
HDMI1
HDMI IN1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
HDMI1
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
HDMI2
HDMI3
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
English-66
PBP3
PICTURE 1: DisplayPort2
Picture 3
HDMI1
HDMI2
HDMI3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
HDMI IN2
HDMI IN3
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
HDMI1
HDMI2
HDMI3
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PBP3
PICTURE 1: DisplayPort1
Picture 3
HDMI1
HDMI IN1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
HDMI1
HDMI2
HDMI3
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PBP3
PICTURE 1: OPTION (DP)
Picture 3
HDMI1
HDMI IN1
HDMI2
HDMI IN2
HDMI3
HDMI IN3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
HDMI1
HDMI2
HDMI3
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
English-67
PBP3
PICTURE 1: OPTION (TMDS)
Picture 3
HDMI1
HDMI2
HDMI3
MP
–
DisplayPort2 DisplayPort1
OPTION
Option board Option board Option board
slot (SLOT2 slot (SLOT2 slot (SLOT2
DisplayPort
IN2
DisplayPort
IN1
Connector
HDMI IN1
HDMI IN2
HDMI IN3
(DP))
(DP+TMDS)) (TMDS))
TERMINAL MODE MODE MODE MODE MODE MODE MODE
Picture 2
Connector
HDMI IN1
HDMI IN2
HDMI IN3
–
–
–
2CH
MODE 1
SETTINGS*1
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
MODE 2
MODE 1
–
1
2
1
2
1
2
1
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
HDMI1
HDMI2
HDMI3
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
MP
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
DisplayPort2
DisplayPort1
DisplayPort IN2
DisplayPort IN1
–
Option board slot
(SLOT2 (DP))
–
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Option board slot
(SLOT2 (DP+TMDS))
OPTION
2CH
Option board slot
(SLOT2 (TMDS))
MODE 1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
*1: SLOT2 CH SETTING for SLOT2 (DP+TMDS)
PICTURE NUMBER: 4 PICTURES
Only one input signal can be selected from within a group.
One of five groups is displayed on each screen. The same group can be selected more than once.
Group A
Group B
Group C
Group D
Group E
HDMI1
HDMI2
HDMI3
MP
HDMI1
HDMI2
HDMI3
MP
DisplayPort1
OPTION (DP)
DisplayPort2
OPTION (TMDS)
NOTE:
HDMI1/HDMI2/HDMI3 TERMINAL SETTINGS is MODE1 only.
OPTION (DP) and OPTION (TMDS) cannot be selected at the same time (Can be choose either one).
Video out
Main picture DisplayPort1 DisplayPort2 HDMI1 HDMI2 HDMI3
OPTION
MP
-
DisplayPort DisplayPort HDMI HDMI HDMI Option board slot Option board slot
Connector
IN1
IN2
IN1
IN2
IN3
(SLOT2 (DP))
(SLOT2 (HDMI))
DisplayPort
Yes
No
No
No
No
Yes
No
No
When the monitor outputs a signal from the DisplayPort out, please select input signal DisplayPort1 or OPTION.
This monitor’s signal output function supports contents, which is protected by HDCP. In this case, up to 3 monitors are connectable.
When using an option, please set SLOT2 CH SETTING to 1CH then set SLOT2 CH SELECT to DisplayPort (See page 45).
NOTE:
To output a signal from the DisplayPort out, some Slot2 type options are only available which have DisplayPort
signal out.
English-68
Features
Reduced Footprint: Provides the ideal solution for environments with superior image quality.
SPECTRAVIEW ENGINE: This system is designed for improvement the visual quality of the monitor.
Each monitor is calibrated at the factory. By making automatic adjustments during operation of the monitor hardware in real
time, optimal settings are configured without any user interaction.
OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six
axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides
the monitor with a uniform color profile. This ensures that the colors displayed on the monitor are exactly the same as on the
color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen
and customise the color accuracy of your monitor to a variety of standards.
sRGB Color Control: A color management standard which allows for color matching on computer monitors and other
peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and
backward compatibility with other common color standards.
OSD (On-Screen-Display) Controls: Allows you to quickly and easily adjust all elements of your screen image via easy to use
on-screen menus.
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing
the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically
optimizing display performance.
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a
lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and
lowering the air conditioning costs of the workplace.
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.
VESA Standard (FDMIv1) Mounting Interface: Allows you to mount the monitor to any VESA standard (FDMIv1) third party
mounting arm or bracket. NEC recommends using mounting equipment which complies with TÜV-GS (Germany) and/or UL1678
standard (North America).
ZOOM: Expands/reduces the image size in horizontal and vertical direction.
Self-diagnosis: If an internal error should occur, a failure state will be indicated.
USB hub: Allows the connection of digital cameras, scanners, keyboards and more.
HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over
a digital signal. If you are unable to view material via the digital input, this does not necessarily mean that the monitor is not
functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected by HDCP and
might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).
Option board slot: You can use an option board. Please contact your supplier for detailed information.
DICOM Sim.: A DICOM gamma curve emulation which is stored inside the monitor as fixed Look Up Table values. When
selecting DICOM Sim., these values are loaded into the active Look Up Table of the monitor to create a DICOM like gamma
correction curve. Suitable for DICOM image viewing in clinical review. Must not be used for DICOM image viewing in
diagnostics.
TILE MATRIX,TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width.
English-69
Troubleshooting
The image is blinking
•
No picture
If you use a signal repeater or distributor or a long
cable, this may cause image roughness or blink for a
moment. In this case please connect the cable to the
monitor directly without using a repeater or a distributor,
or replace the cable with a higher quality cable. Using
a twisted pair extender may cause image roughness
depending on the environment where the monitor is in or
the cable you are using. For further information please
ask your supplier.
•
The signal cable should be completely connected to the
display card/computer.
•
•
The display card should be completely seated in its slot.
Check the main Power Switch, it should be in the ON
position.
•
•
Power Switches for the monitor and computer should be
in the ON position.
Make sure that a supported resolution has been selected
on the display card or system being used. If in doubt,
please refer to the user’s manual of the display controller
or system to change the resolution.
•
Some HDMI cables may not show a correct image.
If input resolution is 1920 x 2160, 3840 x 2160 or
4096 x 2160, please use an HDMI cable which is
approved to support 4K resolution.
•
•
•
Check the monitor and your display card with respect to
compatibility and recommended signal timings.
The image is unstable, unfocused or swimming is
apparent
Check the signal cable connector for bent or pushed-in
pins.
•
The signal cable should be completely attached to the
computer.
The monitor automatically goes into standby at the preset
time period after the video signal was lost. Press the
power on button on the remote control or press the power
button on the monitor.
•
Use the OSD Image Adjust controls to focus and
adjust the display by increasing or decreasing the fine
adjustment.
When the display mode is changed, the OSD Image
Adjust settings may need to be re-adjusted.
•
•
If you unplug the signal cable when starting the computer,
images may not be displayed. Turn off the monitor and
the computer and then connect the signal cable and turn
on the computer and the monitor.
•
•
•
Check the monitor and your display card with respect to
compatibility and recommended signal timings.
Check the OPTION POWER setting when you use option
board accessories.
If text looks garbled, change the video mode to non-
interlaced and use a 60 Hz refresh rate.
The image may be distorted when turning the power on or
Power Button does not respond
changing the settings.
•
Unplug the power cord of the monitor from the AC outlet
to turn off and reset the monitor.
LED on the monitor is not lit (no blue or red color can be
seen)
•
Check the main Power Switch on the monitor.
•
•
•
•
The power Switch should be in the ON position and the
power cord should be connected.
Image persistence
•
Please be aware that LCD Technology may experience
a phenomenon known as Image Persistence. Image
Persistence occurs when a residual or “ghost” image of
a previous image remains visible on the screen. Unlike
CRT monitors, the image persistence of LCD monitors is
not permanent, but single still image being displayed for a
long period of time should be avoided. To alleviate image
persistence, put the monitor into standby via remote
control or turn the monitor’s main power off for as long
as the previous image was displayed. For example, if an
image was on the monitor for one hour and a residual
image remains, the monitor should be in standby or main
power off for one hour to erase the image.
Check the main Power Switch, it should be in the ON
position.
Make certain the computer is not in a power-saving mode
(touch the keyboard or move the mouse).
Check in the OSD that the power indicator option is set to
ON.
LED colors, except for blue, are blinking or glowing
•
A certain failure might have occurred, please contact your
supplier.
•
If the monitor is powered off by the internal temperature
being higher than the normal operating temperature,
the LED will blink green or amber or red for six times.
Power on the monitor again after confirming the internal
temperature has been reduced to normal operation
temperature.
NOTE:
As with all personal display devices, NEC
DISPLAY SOLUTIONS recommends displaying
moving images, using a moving screen saver, or
changing still images at regular intervals whenever
the screen is idle, or turning it into standby or main
power off of the monitor when not in use.
•
The monitor could be in standby.
Press the power on button on the remote control or press
the power button on the monitor.
The image is not properly reproduced
•
Use the OSD Image Adjust controls to increase or
decrease the coarse adjustment.
•
Make sure that a supported resolution has been selected
on the display card or system being used.
If in doubt, please refer to the user’s manual of the display
card or system to change the resolution.
English-70
Selected resolution is not displayed properly
Snowy Picture, Poor Sound in TV
•
Use OSD Display Mode to enter Information menu and
confirm that the appropriate resolution has been selected.
If not, select corresponding option.
•
Check antenna/cable connection. Use new cable if
necessary.
The USB Hub does not operate
No Sound
•
Check to make sure that the USB cable is properly
•
Check to see if the audio cable is properly connected.
connected. Refer to your USB device user’s manual.
•
Check to see if MUTE is activated. Use the remote control
to enable or disable the Mute function.
•
Check if the USB upstream port on the monitor is
connected to the USB downstream port on the computer.
Please make sure the computer is ON or USB POWER is
ON.
•
•
Check to see if VOLUME is set to a minimum.
Check to see if the computer supports an audio signal
through DisplayPort.
If unsure, contact your supplier.
•
•
Check the format if this device cannot recognize the
connected USB memory.
Disconnect one upstream USB cable when using
2 upstream connections.
•
When LINE OUT is not functioning, check to see if
SURROUND is ON.
•
•
Check the Internal/External speaker switch.
Interference in TV
•
Check components for shielding, move away from
If HDMI CEC audio device is not connected, please set
“AUDIO RECEIVER” to OFF.
monitor if necessary.
USB or RS-232C or LAN control is not available
The Remote Control is not functioning
•
Check RS-232C (reverse type) or the LAN cable.
A category 5 or higher LAN cable is required for
connection.
•
•
•
Check the batteries status of the Remote Control.
Check if the batteries are inserted correctly.
Check if the Remote Control is pointing at the remote
•
Check USB cable connected to USB2 port.
Check the EXTERNAL CONTROL is set to ENABLE then
PC SOURCE is set to EXTERNAL PC.
control sensor of the monitor.
•
•
Check the status of IR LOCK SETTINGS.
The remote control system may not function when direct
sunlight or strong illumination strikes the remote control
sensor of the monitor, or when there is an object in the
path.
The monitor goes into standby automatically
•
Please check “OFF TIMER” setting.
•
Set the “CEC” function to OFF.
Media player function does not recognize the USB
storage device
The SCHEDULE/OFF TIMER function is not working
properly
•
Please check a USB storage device is connected to the
USB MP.
•
The “SCHEDULE” function will be disabled when the
“OFF TIMER” is set.
•
If the “OFF TIMER” function is enabled and the power to
the LCD monitor is turned off when the power supply is
interrupted unexpectedly, then the “OFF TIMER” will be
reset.
MicroSD card does not work
•
Check to make sure the microSD card is properly
connected.
•
Check the microSD memory card format.
Either light vertical or horizontal stripes may appear, depending on the specific image pattern. This is not a product fault or degradation.
English-71
Specifications - C751Q
Product Specifications
LCD Module
75"/189.27 cm diagonal
Pixel Pitch: 0.430 mm
Resolution: 3840 x 2160
Color: Over 1073 million colors (depending on display card used)
Brightness: 350 cd/m2 (Max.) @25°C
Contrast Ratio: 1200:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Horizontal: 31.5 kHz - 91.1 kHz
Vertical: 24.0 - 85.0 Hz (Digital Input)
Pixel Clock
Digital: 25.0 MHz - 600.0 MHz (HDMI/DisplayPort)
1649.66 x 927.94 mm
Viewable Size
Input Signal
DisplayPort DisplayPort Connector Digital RGB
DisplayPort V1.2 (HDCP 1.3)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (24Hz/30Hz/60Hz
(DisplayPort1.2))
HDMI
HDMI Connector
Digital YUV
Digital RGB
HDMI (HDCP 1.4/2.2)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,
3840x2160 (30Hz/24Hz/25Hz/60Hz (MODE2)), 4096x2160 (30Hz/24Hz/25Hz/60Hz
(MODE2))*1, *3
Output Signal
DisplayPort DisplayPort Connector Digital RGB
AUDIO
AUDIO
DisplayPort V1.2 (HDCP 1.3)
Stereo Mini Jack
HDMI Connector
Analog Audio
Digital Audio
Stereo L/R 0.5 Vrms
Input
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
Stereo Mini Jack Analog Audio
AUDIO
Output
Speaker Output
External Speaker Jack 15 W + 15 W (8 ohm)
Internal Speaker 10 W + 10 W (Stereo)
Control
RS-232C In: 9 Pin D-sub
LAN: RJ-45 10 BASE-T/100 BASE-TX x 2
Remote IN: Stereo Mini Jack 3.5 mm Ø
SD card Hub
USB Hub
Port: microSD card. Up to 32GB microSDHC is supported.
USB1: USB 2.0 Downstream port
USB2: USB 2.0 Upstream port
USB CM1 (2A): Power supply port, 5V/2A (max.)
USB CM2: USB service port for maintenance
USB MP: Media Player/Firmware update port
Power Supply
4.4 - 1.9 A @ 100-240V AC, 50/60Hz
Normal operation: Approx. 195 W
Power Consumption
Operational Environment
Temperature*2: 0 - 40°C / 32 - 104°F
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension*4
1681.2 (W) x 959.6 (H) x 71.1 (D) mm/66.2 (W) x 37.8 (H) x 2.8 (D) inches
Weight
52.6 kg (116.0 lbs)
400 mm x 400 mm (M8, 4 Holes)
VESA DPM
VESA compatible mounting interface
Power Management
Power supply for Slot 2 type OPTION
16V/4.7 A
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: When you use option board accessories, please contact your supplier for detailed information.
*3: Reproduced text may look blurred.
*4: Measurements are of the monitor only and do not include removable parts that protrude.
English-72
Specifications - C861Q
Product Specifications
LCD Module
86"/217.43 cm diagonal
Pixel Pitch: 0.494 mm
Resolution: 3840 x 2160
Color: Over 1073 million colors (depending on display card used)
Brightness: 350 cd/m2 (Max.) @25°C
Contrast Ratio: 1200:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Horizontal: 31.5 kHz - 91.1 kHz
Vertical: 24.0 - 85.0 Hz (Digital Input)
Pixel Clock
Digital: 25.0 MHz - 600.0 MHz (HDMI/DisplayPort)
1895.04 x 1065.96 mm
Viewable Size
Input Signal
DisplayPort DisplayPort Connector Digital RGB
DisplayPort V1.2 (HDCP 1.3)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (24Hz/30Hz/60Hz
(DisplayPort1.2))
HDMI
HDMI Connector
Digital YUV
Digital RGB
HDMI (HDCP 1.4/2.2)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,
3840x2160 (30Hz/24Hz/25Hz/60Hz (MODE2)), 4096x2160 (30Hz/24Hz/25Hz/60Hz
(MODE2))*1, *3
Output Signal
DisplayPort DisplayPort Connector Digital RGB
AUDIO
AUDIO
DisplayPort V1.2 (HDCP 1.3)
Stereo Mini Jack
HDMI Connector
Analog Audio
Digital Audio
Stereo L/R 0.5 Vrms
Input
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
Stereo Mini Jack Analog Audio
AUDIO
Output
Speaker Output
External Speaker Jack 15 W + 15 W (8 ohm)
Internal Speaker 10 W + 10 W (Stereo)
Control
RS-232C In: 9 Pin D-sub
LAN: RJ-45 10 BASE-T/100 BASE-TX x 2
Remote IN: Stereo Mini Jack 3.5 mm Ø
SD card Hub
USB Hub
Port: microSD card. Up to 32GB microSDHC is supported.
USB1: USB 2.0 Downstream port
USB2: USB 2.0 Upstream port
USB CM1 (2A): Power supply port, 5V/2A (max.)
USB CM2: USB service port for maintenance
USB MP: Media Player/Firmware update port
Power Supply
5.0 - 2.1 A @ 100-240V AC, 50/60Hz
Normal operation: Approx. 230 W
Power Consumption
Operational Environment
Temperature*2: 0 - 40°C / 32 - 104°F
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension*4
1928.2 (W) x 1099.2 (H) x 74.3 (D) mm/75.9 (W) x 43.3 (H) x 2.9 (D) inches
Weight
57.8 kg (127.4 lbs)
400 mm x 400 mm (M8, 4 Holes)
VESA DPM
VESA compatible mounting interface
Power Management
Power supply for Slot 2 type OPTION
16V/4.7 A
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: When you use option board accessories, please contact your supplier for detailed information.
*3: Reproduced text may look blurred.
*4: Measurements are of the monitor only and do not include removable parts that protrude.
English-73
Specifications - C981Q
Product Specifications
LCD Module
98"/247.82 cm diagonal
Pixel Pitch: 0.562 mm
Resolution: 3840 x 2160
Color: Over 1073 million colors (depending on display card used)
Brightness: 350 cd/m2 (Max.) @25°C
Contrast Ratio: 1300:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Horizontal: 31.5 kHz - 91.1 kHz
Vertical: 24.0 - 85.0 Hz (Digital Input)
Pixel Clock
Digital: 25.0 MHz - 600.0 MHz (HDMI/DisplayPort)
2158.85 x 1214.40 mm
Viewable Size
Input Signal
DisplayPort DisplayPort Connector Digital RGB
DisplayPort V1.2 (HDCP 1.3)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 3840x2160 (24Hz/30Hz/60Hz
(DisplayPort1.2))
HDMI
HDMI Connector
Digital YUV
Digital RGB
HDMI (HDCP 1.4/2.2)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60, WUXGA60, 1920x1080 (60 Hz),
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz,
3840x2160 (30Hz/24Hz/25Hz/60Hz (MODE2)), 4096x2160 (30Hz/24Hz/25Hz/60Hz
(MODE2))*1, *3
Output Signal
DisplayPort DisplayPort Connector Digital RGB
AUDIO
AUDIO
DisplayPort V1.2 (HDCP 1.3)
Stereo Mini Jack
HDMI Connector
Analog Audio
Digital Audio
Stereo L/R 0.5 Vrms
Input
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
Stereo Mini Jack Analog Audio
AUDIO
Output
Speaker Output
External Speaker Jack 15 W + 15 W (8 ohm)
Internal Speaker 10 W + 10 W (Stereo)
Control
RS-232C In: 9 Pin D-sub
LAN: RJ-45 10 BASE-T/100 BASE-TX x 2
Remote IN: Stereo Mini Jack 3.5 mm Ø
SD card Hub
USB Hub
Port: microSD card. Up to 32GB microSDHC is supported.
USB1: USB 2.0 Downstream port
USB2: USB 2.0 Upstream port
USB CM1 (2A): Power supply port, 5V/2A (max.)
USB CM2: USB service port for maintenance
USB MP: Media Player/Firmware update port
Power Supply
6.1 - 2.6 A @ 100-240V AC, 50/60Hz
Normal operation: Approx. 240 W
Power Consumption
Operational Environment
Temperature*2: 0 - 40°C / 32 - 104°F
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension*4
2193.8 (W) x 1248.8 (H) x 93.0 (D) mm/86.4 (W) x 49.2 (H) x 3.7 (D) inches
Weight
90.0 kg (198.4 lbs)
400 mm x 400 mm (M8, 4 Holes)
VESA DPM
VESA compatible mounting interface
Power Management
Power supply for Slot 2 type OPTION
16V/4.7 A
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: When you use option board accessories, please contact your supplier for detailed information.
*3: Reproduced text may look blurred.
*4: Measurements are of the monitor only and do not include removable parts that protrude.
English-74
Manufacturer’s Recycling and Energy Information
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top
priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly
products, and always strive to help define and comply with the latest independent standards from agencies such as ISO
(International Organisation for Standardization) and TCO (Swedish Trades Union).
Disposing of your old NEC product
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures
and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.
All required information concerning the disposal of the product and country-specific information on recycling facilities can be
found on our following websites:
http://www.nec-display.com (in Japan) or
http://www.necdisplay.com (in USA).
Energy Saving
This monitor features an advanced energy saving capability. When a Display Power Management signal is sent to the monitor,
the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.
For additional information visit:
http://www.necdisplay.com/ (in USA)
http://www.nec-display-solutions.com/ (in Europe)
For ErP requirement/For ErP (Network standby) requirement:
Setting:
CONTROL
USB
USB POWER
AUTO
Condition: Without any option board.
INPUT DETECT is set to a setting except for NONE.
USB POWER is set to ON.
DisplayPort is set to MST.
Power consumption: 2 W or less (Glowing amber).
Time for power management function: 10 sec. (Default setting)
(Except for a condition that the monitor has plural signal inputs.)
Power consumption: 0.5 W or less (Blinking amber).
Time for power management function: 3 min. (Default setting)
(Except for a condition that the monitor has plural signal inputs.)
English-75
WEEE Mark (European Directive 2012/19/EU and amendments)
Disposing of your used product: In the European Union
EU-wide legislation as implemented in each Member State requires that used electrical and electronic products
carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors
and electrical accessories, such as signal cables or power cords. When you dispose of such products, please
follow the guidance of your local a uthority or ask the shop where you purchased the product, or if applicable,
follow applicable legislation or agreement you may have. The mark on electrical and electronic products may
only apply to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority
and ask for the correct method of disposal.
For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household
waste! There is a separate collection system for used batteries, to allow proper treatment and recycling in
accordance with legislation.
According to EU directive 2006/66/EC, the battery can’t be disposed improperly.The battery shall be separated to
collect by local service.
English-76
[Notice] About the MPEG-4 AVC,
MPEG-4 Visual license included in this product
1. MPEG-4 AVC
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF
A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN
COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY
A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED
TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM
2. MPEG-4 Visual
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL
STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR
ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND
COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM.
English-77
|