Instruction Manual
UC 3001A
UC 3501A
UC 4001A
Important:
Read this instruction manual carefully before putting the chain saw into operation and strictly observe
the safety regulations!
Keep this instruction manual!
Delivery inventory
1
2
3
1.
2.
3.
4.
5.
6.
Electric chain saw
Guide bar
Saw chain
Chain protection cover
Universal wrench
Instruction manual (not shown)
4
In the case that one of the parts listed should not be included in
the delivery inventory, please, consult your sales agent.
5
EU Conformity Declaration
Packing
The MAKITA electric chain saw will be delivered in a protective
cardboard box to prevent transport damages.
The undersigned, Junzo Asada and Rainer Bergfeld, as
authorized by DOLMAR GmbH, declare that the MAKITA
machines,
Cardboardisabasicrawmaterialandisthereforeconsequently
reuseable or suitable for recycling (waste paper recycling).
Type: 225
EU prototype test certificate No.
UC 3001A
UC 3501A
UC 4001A
M6 98 06 24243 025
M6 98 06 24243 025
M6 98 06 24243 025
manufactured by DOLMAR GmbH, Jenfelder Str. 38, 22045
Hamburg, Germany, conforms to the basic safety and health
requirements of the applicable EU guidelines:
RE Y
EU Machine guideline 98/37/ EG, EU EMC guideline 89/336/
EWG (modified by 91/263/ EWG, 92/31/ EWG and 93/68/
EWG), EU Low-voltage guideline 73/23/ EWG (modified by
93/68/ EWG), Noise emission 2000/14/EG.
The most important standards applied to properly meet the
requirements of the above EU guidelines were:
EN 50144-1, HD 400.1, HD 400.3, EN 55014, EN 55014-2, EN
60555-T3, -T3/A1, EN 61000-3-2.
The conformity assessment procedure 2000/14/EG was
performed per Annex V. The measured sound power level
(Lwa) is 99 dB(A). The guaranteed sound power level (Ld) is
101 dB(A).
The EU Type-Examination per 98/37/EG was performed by:
TÜV Product Service GmbH, Zertifizierstelle, Ridlerstr. 31,
D-80339 München.
Hamburg, 1.12. 2001
For DOLMAR GmbH
Junzo Asada
Rainer Bergfeld
Managing Director
Managing Director
3
SAFETY PRECAUTIONS
General precautions
-
To ensure correct operation the user has to read this
instruction manual to make himself familiar with the
characteristics of the electric chain saw. Users insufficiently
informed will risk danger to themselves as well as others due
to improper handling.
-
-
It is recommended only to lend the electric chain saw to people
who have proven to be experienced with electric chain saws.
Always hand over the instruction manual.
First users should ask the dealer for basic instructions to
becomefamiliarizedwiththecharacteristicsofenginepowered
sawing.
1
-
-
Familiarize yourself with the use of an electric chain saw by
cutting off lengths from a log on a sawhorse.
Children and young persons aged under 18 years must not be
allowedtooperatetheelectricchainsaw. Personsovertheage
of 16 years may, however, use the chain saw for the purpose
of being trained while under supervision of a qualified trainer.
Use electric chain saws always with the utmost care and
attention.
Operate the electric chain saw only if you are in good physical
condition. Perform all work calm and carefully. The user has to
accept liability for others.
-
-
-
Never use the electric chain saw after the consumption of
alcohol or drugs or medication.
2
Personal protective equipment
-
-
-
In order to avoid head, eye, hand or foot injuries as well as
toprotectyourhearingthefollowingprotectiveequipment
must be used during operation of the electric chain saw.
The kind of clothing should be appropriate, i. e. it should be
tight-fitting but not be a hindrance. Do not wear jewellery or
clothing which could become entangled with bushes or shrubs.
The protective helmet (1) is to be checked in regular intervals
for damage and is to be replaced after 5 years at the latest. Use
only approved protective helmets.If you have long hair wear a
hairnet.
1
3
-
The face shield (2) of the protective helmet (or the goggles)
protect against sawdust and wood chips. During operation of
the electric chain saw always wear a goggle or a face shield to
prevent eye injuries.
2
3
-
-
Wear adequate noise protection equipment (ear muffs (3),
ear plugs, etc.). Octave brand analysis upon request.
The protective brace and bib overall (4) is made of a nylon
structure with 22 layers and protects against cuts. We strongly
recommend its use. In any case wear a long pair of trousers
made of solid material during operation of the electric chain
saw.
-
-
Protective gloves (5) made of thick leather are part of the
prescribedequipmentandmustalwaysbewornduringoperation
of the electric chain saw.
During operation of the electric chain saw safety shoes or
boots (6) fitted with anti skid sole, steel toe caps and protection
for the leg are always to be used. Safety shoes equipped with
a protective layer provide protection against cuts and ensure a
secure footing.
6
4
5
4
Putting into operation
-
-
-
-
Do not operate the electric chain saw when it rains or in wet or
moist environment because the motor is not waterproof.
If the electric chain saw is moist, it must not be put into
operation.
Do not operate the electric chain saw next to inflammable
gases or dusts. Explosion hazard.
Do always lead the power supply cable behind the user. Take
care that the cable is not clamped or cut by sharp-edged
objects. Lay the cable such that nobody is endangered.
Inserttheplugonlyintosafetysocketswithapprovedinstallation.
Make sure that the mains voltage corresponds to that on the
identification plate. Back-up fuse 16 A. If the saw is going to be
used outdoors connect it to a fault-current (FI) circuit breaker
with max. 30 mA triggering current.
-
5
4
-
-
Pay attention to the diameter of the extension cable. When
using a cable roll the cable should be completely wound off.
Use only extension cords that meet the specifications in
“Technical data”. If using the saw out of doors make sure that
the extension cord is approved for such use.
Beforestartingworktheelectricchainsawmustbechecked
for perfect function and operating safety according to the
prescriptions.
Check especially the function of the chain brake, the correct
mountingoftheguidebar,thecorrectsharpeningandtightening
of the saw chain, the firm mounting of the sprocket guard, the
easy motion of the power switch, the function of the locking
button, the good mechanical condition of cable and plug and
the cleanliness and dryness of the handles.
6
-
Put the electric chain saw only into operation if it is completely
assembled. Never use the electric chain saw when it is not
completely assembled.
-
-
All protective installations and guard supplied with the chain
saw during operation.
Make sure that there are no children or other persons within the
working range. Also pay attention to any animals in the working
vicinity (6).
-
-
Before switching on the electric chain saw ensure that you
have a safe footing.
When switching on the electric chain saw always hold it
withbothhands. Takethebackhandlewiththerighthandand
the tubular handle with the left hand. Hold the handles tightly
with your thumbs facing your fingers. The bar and chain must
indicate away from your body (7).
7
-
-
Switch on the saw only in the manner described in this manual.
Do not overload your saw. It will work better and more safely if
you use it within its intended performance range.
Switch off the electric chain saw immediately if you observe a
change in its operating behavior.
CAUTION:
When releasing the power switch the chain keeps on
running for a short period of time (free-wheeling).
Protect the power cord from heat, oil and sharp edges.
If the cable is being damaged or cut, pull out the power supply
plug immediately.
-
-
-
-
-
If the sawing device is hit by stones, nails or other hard objects,
pull out the power supply plug and check the sawing device
immediately
Pull out the power supply plug before checking the chain
tension, tightening the chain, replacing it or clearing
malfunctions.
When stopping work or leaving the electric chain saw switch off
the chain saw and pull out the power supply plug. Put the
electricchainsawinasafelocationtopreventdangertoothers.
For refilling the oil tank the power supply plug must be pulled
out. Do not smoke or light open fires.
8
● device malfunction
● maintenance
● refill oil
-
-
-
-
Avoid skin or eye contact with mineral oil products. Always
wear gloves when refilling the oil tank.
Take care that no chain oil oozes into the soil (environmental
protection). Use an appropriate base.
● sharpen the saw chain
● stop
● transport
If oil has been spilt, clean the electric chain saw immediately.
●
shutdown
Working behavior/method of working
9
-
-
-
Do not work on your own. There must be someone around in
case of an emergency (within shouting distance).
During sawing operation always hold the electric chain saw
with both hands. Thus you will be able to guide it safely.
Only use the electric chain saw during good light and visibility
periods. Be aware of slippery or wet areas, and of ice and snow
(risk of slipping). The risk of slipping is extremely high when
working on recently peeled wood (bark).
-
Never work on unstable surfaces. Make sure that there are no
obstacles in the working area, risk of stumbling. Always ensure
that you have a safe footing.
-
-
-
Never saw above your shoulder height.
Never saw while standing on a ladder.
Never climb up into trees to perform sawing with the electric
chain saw.
10
-
Never bend forward by far to perform sawing.
5
-
Guide the electric chain saw in such a way that no part of your
body is within the elongated swiveling range of the saw (11).
-
-
Use the electric chain saw for sawing wood only.
Do not let the chain touch the ground when it is running. If you
are cutting wood lying directly on the ground, turn it over before
completing the cut so that you do not cut into the ground.
-
-
Clear the area of the cut of foreign objects such as sand,
stones, nails, wire etc. Such objects can damage the blade and
cause dangerous kickback.
When sawing precut timber or thin woods use a safe support
(sawingjack,12). Whensawingprecuttimberorthinpiecesuse
a stable support (sawhorse, 12). Do not saw stacked timber!
Do not let another person steady the timber, and do not steady
it with your foot!
11
-
-
Secure round timber.
When working on slopes, always work facing the slope.
Z
-
-
Forperformingcrosscutsthetoothedledge(12,Z) mustbe
applied to the timber to be cut.
Before performing a crosscut firmly apply the toothed ledge to
the timber, only then can the timber be cut with the chain
running. For this the electric chain saw is lifted at the back
handle and guided with the tubular handle. The toothed ledge
serves as a center of rotation. Continue by slightly pressing
downthetubularhandleandsimultaneouslypullingbackwards
theelectricchainsaw. Applythetoothedledgealittlebitdeeper
and once again lift the back handle.
12
-
-
-
The sawing device must be running whenever you remove the
electric chain saw from the timber.
When performing several cuts the electric chain saw must be
switched off in between.
When the timber must be pierced for cutting or longitudi-
nal cuts are to be performed it is urgently recommended to
have these works carried out by specially trained persons
only (high risk of kickbacks).
-
-
For performing longitudinal cuts(13) apply the sawing device
at an angle which is as small as possible. Be very careful when
carrying out this kind of work because the toothed ledge cannot
be used.
13
When cutting with the top edge of the bar the electric chain saw
may be pushed in the direction of the user if the chain is
clamped. For this reason use the bottom edge of the bar
whenever possible. The electric chain saw will then be pushed
away from your body (14).
-
If the timber is not free of tension (15), first cut the pressure side
(A). Then the crosscut can be performed on the tension side
(B). Thus clamping of the bar is avoided.
-
-
-
-
-
Be very careful when cutting splintery wood. Cut pieces of
wood may be pulled along (risk of injuries).
Never use the electric chain saw for lifting up or removing
pieces of wood or other objects.
14
When releasing the tension the electric chain saw should be
supported on the trunk (risk of kickbacks).
Tension releasing works must be carried out by trained
persons. High risk of injuries.
Be aware of branches under tension. Do not cut free branches
from below.
B
A
B
-
-
Never perform tension releasing works standing on the trunk.
Do not use the electric chain saw for works in the forest,
i.e.forcuttingdowntreesorcarryingouttensionreleasing
works. The user's mobility and safety necessary for this
kindofworkarenotguaranteedduetothecableconnection.
15
6
CAUTION:
Do not fell or debranch trees unless you are specially
trained for it! There is a high risk of injury! Make sure to
follow local regulations.
45°
-
Before cutting down a tree ensure that
a) only those persons are within the working range which are
actually involved in cutting down the tree
21
2
45°
b) b) all persons involved in the felling have an unhindered
retreat route (the retreat path should be about 45° diago-
nally and to the rear away from the direction of fall). Be
aware of the increased risk of stumbling from electric
cables!
= cutting down range
c) the bottom part of the trunk is free from foreign bodies,
underbrushandbranches. Makesuretohaveasafefooting
(risk of stumbling).
16
d) the next working place is at least 2 1/2 tree lengths away
(16). Before cutting down the tree check the direction of fall
and make sure that there are neither other persons nor any
objects within a distance of 2 1/2 tree lengths (16).
Judging the tree:
Direction of hanging - loose or dry branches - height of the tree
- natural hang over - is the tree rotten?
Take into account the direction and the velocity of the wind. If
strong gusts are occuring, do not perform any cutting down
works.
-
-
-
-
o
45
A
A
Cutting the roots:
Start with the strongest root. First perform the vertical and then
the horizontal cut.
Notching the trunk (A, 17):
The notch determines the direction of fall and guides the tree.
The trunk is notched perpendicular to the direction of fall and
penetrates 1/3 -1/5 of the trunk diameter. Perform the cut near
the ground.
17
-
When correcting the cut always do so over the whole width of
the notch.
-
-
Cut down the tree (B, 18) above the bottom edge of the notch
(D). The cut must be exactly horizontal. The distance between
both cuts must be approx. 1/10 of the trunk diameter.
The material between both cuts (C) serves as a hinge. Never
cut it through, otherwise the tree will fall without any control.
Insert felling wedges in the cut (B, 18) in good time.
Secure the cut only with wedges made of plastic or aluminium.
Do not use iron wedges.
When cutting down a tree always stay sideways of the falling
tree.
When withdrawing after having performed the cut down be
aware of falling branches.
C
-
-
-
-
D
B
B
C
Whenworkingonaslopinggroundtheuseroftheelectricchain
saw must stay above or sidewards of the trunk to be cut or the
already cut down tree.
18
-
Be aware of trunks which may roll towards you.
Kickback
-
Whenworkingwiththeelectricchainsawdangerouskickbacks
may occur.
-
-
Kickback occurs when the tip of the blade(especially the top
quarter) inadvertently comes into contact with wood or other
solid objects.
In this case the electric chain saw is thrown without any control
and with high energy potentials in the direction of the user (risk
of injuries).
In order to prevent kickbacks follow the indicated
instructions:
-
-
Never apply the end of the bar when starting to make a cut.
Always observe the end of the bar.
Never use the bar end for sawing. Be careful when continuing
to cut.
-
-
When starting to perform a cut the chain must be running.
Ensure that the chain is always sharpened correctly. Pay
special attention to the hight of the depth limiter (for detailed
information see the chap. "Sharpening the saw chain").
Never cut several branches at the same time. When cutting a
branch ensure that no other branch is touched.
When crosscutting a trunk be aware of the trunks next to it. It
is recommended to use a saw jack.
19
-
-
7
Transport and storage
-
Carry the electric chain saw with the tubular handle. The
saw bar indicates backwards. Never carry or transport
the electric chain saw with the chain running.
Never carry the saw by the power cord. Do not disconnect
the plug by pulling on the power cord.
When changing your position during work switch of the
electric chain saw and actuate the chain brake in order to
prevent an inadvertent start of the chain.
-
-
-
Whentransportingtheelectricchainsawoverlongdistances
the power supply plug must be pulled out and the bar
protection cover, included in the delivery, must be applied
(20).
20
-
-
-
-
Ensure safe positioning of the electric chain saw during car
transportation to avoid oil leakage.
Store the saw in a secure, dry, lockable room out of reach
of children. It must not be stored outdoors.
For storing the electric chain saw over a long period of time
or shipping it the oil tank must be completely emptied.
Only use approved and marked containers for transporting
and storing chain oil.
Maintenance
-
Forperformingmaintenanceworksswitchoftheelectric
chain saw, pull out the power supply plug and secure
it (21).
-
Before starting to work, always make sure that the saw is in
safe working order, in particular the chain brake and run-
outbrake.Makesurethatthesawchainisalwayssharpened
and tightened correctly (22).
21
-
-
Havethechainbrakeandrun-outbrakeinspectedregularly
(see “Chain brake, run-out brake”).
Regularly check the cable to the power supply for damage
of the covering.
-
-
Regularly clean the electric chain saw.
If the plastic case is damaged, have it immediately repaired
by a skilled person.
-
-
Regularly check the tank cap for tightness.
Do not use the saw if the ON/OFF switch is defective. Have
it repaired by a qualified person.
Observe the accident prevention instructions issued
by the competent trade federations and insurance
companies.
Do not perform any modifications on the electric chain
saw. You will endanger your safety.
Perform only the maintenance and repair works described
in the instruction manual. All other works must be carried
out by the MAKITA service.
Use only original MAKITA spare parts and accessories.
Applying spare parts which are not original MAKITA parts
oraccesoriesandbar/chaincombinationsorlengthsresults
in a high risk of accidents. For accidents and damage
resulting from using sawing devices or accesories which
havenotbeenapprovedwecannotacceptanyresponsibility.
22
23
24
First aid
For the event of a possible accident, please, make sure that
SERVICE
a first aid box is always immediately available close by.
Immediately replace any items used from the first aid box.
Should you ask for help, please, give the following
information:
- place of accident
- what happened
- number of injured persons
- kind of injuries
- your name.
NOTE
Individuals with poor circulation who are exposed to excessive
vibrationmay experienceinjury tobloodvessels or thenervous
system.
Vibration may cause the following symptoms to occur in the
fingers, hands or wrists: ”Falling asleep” (numbness), tingling,
pain, stabbing sensation, alteration of skin colour or of the skin.
If any of these symptoms occur, see a physician!
8
Technical data
UC 3001A
UC 3501A
UC 4001A
Power consumption
Nominal voltage
Mains frequency
Nominal current
Cable length
Watt
V
Hz
A
1800
230-240 ~
50...60
7.8
cm
30
Chain type
092
Chain pitch
Length of a cut
Max. chain speed
inch
cm
m/s
3/8"
35
13.3
30
40
Sound power level LWA av
per ISO 9207 1)
dB (A)
102
Sound pressure level LpA av
at the workplace per ISO 7182 1)
dB (A)
89
Vibration acceleration
ah,w av per ISO 7505 1)
- Tubular handle
- Rear handle
m/s2
m/s2
4
7
Oil pump
Oil tank capacity
automatic
0.12
l
Power transmission
Overload protection
direct
mechanic (slip clutch)
Chain brake
manual or automatic
Run-out brake
electrical
4.2
Weight
(without bar/chain)
kg
Radio interference suppression / EMC
Protective case
Extension cable
(not included)
Per EMC guidelines EWG 89/336 and EWG 92/31
class II (double protective insulation)
DIN 57282/ HO 7RN-F
L= 30 m max., 3x1.5 mm2
1) Figures derived in equal part from full-load and top-speed operation.
1
2
Denomination of components
3
Figure: Identification plate UC 4001A
4
5
6
Serial number
Year of manufacture
7
8
Indicate when ordering spare parts!
1 Tubular handle
2 Hand guard
3 Spike bar
4 Fastening nut
10
15
9
11 12
13
5 Sprocket guard, chain brake
6 Carbon brush cover
7 Back hand guard
8 Power cord with plug
9 Guide bar
16
10 Oil tank cap
11 Identification plate
12 Locking button
13 Rear handle
14 Power switch
15 Sightglass for oil level
16 Saw chain
14
9
PUTTING INTO OPERATION
Mounting the guide bar and saw chain
CAUTION: When working on the guide bar or saw chain
always wear protective gloves and pull out the
power supply plug.
Use the universal wrench delivered with the machine.
Put the electric chain saw on a stable surface and carry out the
following operations for mounting the bar and chain:
CAUTION: Switch on the electric chain saw only after
having assembled it completely and inspec-
ted!
7
5
6
4
3
1
2
B
A
-
-
-
Unscrew retaining nut (A/2).
-
-
Lay the chain (B/5) on the guide bar (B/6).
Pull off the sprocket guard (A/1).
The cutting edges (B/7) of the chain on the top edge of the
guide bar must face in the direction shown by the arrow.
Turn the chain adjusting screw (A/3) to the left (counter-
clockwise) until the pin (A/4) is at the left stop.
8
9
D
C
-
Pull the chain around the sprocket (C/8) and into the
sprocket teeth (C/9).
-
Position the guide bar. Take care that the pivot (A/4) of the
chain tightener is inserted into the bore (see circle) of the
guide bar.
10
2
1
F
E
Tightening the saw chain
-
-
When putting on the sprocket guard (E/1) make sure that
thesprocketguardlug(E/10)fitsintothehole(seeenlarged
illustration).
-
Slightly lift the end of the guide bar and turn the chain
tightener screw (A/3) to the right (clockwise) until the saw
chain rests against the bottom side of the guide bar (see
circle).
Tighten mounting nut (E/2) lightly by hand.
-
Continue to lift the guide bar end and firmly tighten the
fastening nut (E/2) by means of the universal wrench.
10
Checking the chain tension
The chain has the proper tension when it lies against the
bottom edge of the guide bar and can be easily pulled by hand
about 5 mm (a little under 1/4") up from the guide bar.
Check the chain tension frequently - new chains tend to get
longer during use!
When checking the chain tension the motor must be switched
off and the power supply plug pulled out.
HINT:
Use 2 or 3 saw chains alternately for even wear of the chains,
sprocket and guide bar running surfaces.
In order to guarantee a uniform wear of the groove in the bar the
bar should be turned over whenever replacing the chain.
G
Chain brake
2
1
11
H
I
The UC 3001A, UC 3501A and UC 4001A comes with an
inertial chain brake as standard equipment. If kickback occurs
due to contact of the guide-bar tip with wood (see SAFETY
PRECAUTIONS, page 7), the chain brake will stop the chain
through inertia if the kickback is sufficiently strong.
Engaging the chain brake (braking)
If the kickback is strong enough the sudden acceleration of the
guide bar combined with the inertia of the hand guard (I/11) will
automatically actuate the chain brake.
To engage the chain brake manually, simply push the hand
guard (I/11) forward (towards the tip of the saw) with your left
hand (arrow 1).
The chain will stop within a fraction of a second.
Releasing the chain brake
Run-out brake
The UC 3001A, UC 3501A and UC 4001A come with a run-out
brake as standard equipment.
Pull the hand guard (I/11) towards you (arrow 2) until you feel
it catch. The brake is now released.
Note:
The run-out brake ensures that the chain comes to a stop
immediately when the ON/OFF switch is released, thus
preventing the chain from continuing to run and presenting a
hazard.
When the chain brake is actuated the power supply to the
motor will be cut off. Testing of the chain brake is described on
page 13.
Testing of the run-out brake is described on page 14.
Chain and run-out brake maintenance
SERVICE
The brake systems are very important safety features, and
like any other part they are subject to a certain amount of
wear. Regular inspection and maintenance is important
for your personal safety, and can be properly performed
only by a MAKITA service centre.
11
Saw chain oil
Waste oil
A
B
Use a special oil with adhesive addition for lubricating the saw
chain and bar. The adhesive addition prevents that the oil is
centrifuged too fast from the sawing device.
Never use waste oil
Waste oil is very dangerous for the environment.
Waste oil contains high amounts of carcinogenic substances.
Do not use mineral oils. In order to protect the invironment the
use of biologically decomposeable oil is prescribed.
The residues in the waste oil result in a high degree of wear and
tear at the oil pump and the sawing device.
The saw chain oil sold by MAKITA, called BIOTOP, is made of
special vegetable oils and is biologically decomposeable to
100%. BIOTOP has been granted the "blue angel" for being
particularly favourable to the environment (RAL UZ 48).
Inthecaseofdamagecausedbyusingwasteoilorunappropriate
saw chain oil the product guarantee will be null and void.
Your salesman will inform you about the use of saw chain oil.
Biologically decomposeable oil is stable only for a limited period
of time. It should be consumed within 2 years from the date of
manufacture (printed on the container).
Avoid skin and eye contacts
Mineral oil products as well as oil degrease the skin. If your skin
repeatedly comes in contact with these substances for a longer
period of time, it will desiccate. Various skin deseases may
result. In addition, allergic reactions are known.
BIOTOPoilisavailableinthefollowingpackingsizestosuityour
individual requirements:
Eyes can be irritated by contact with oil. If oil gets into your eyes,
immediately wash them with clear water. If your eyes are still
irrritated, go to see a doctor.
1 liter
order number 980 008 610
order number 980 008 611
5 liters
Refilling the oil tank
1
2
D
C
Onlyif themotorisswitched off and thepowersupplyplug
is pulled out
-
The oil level can be controlled in the sight glass (D/2).
Lubricating the saw chain
-
Thoroughly clean the oil tank around the cap to prevent dirt
from entering the tank.
In order to ensure sufficient lubrication of the saw chain there
must always be enough oil in the tank. Its contents (120 ml) is
sufficient for approx. 1/2 hour at continuous operation.
Important note on bio-degradable chain oils:
If you are not planning to use the saw again for an extended
period of time (longer than the expiration date of the chain oil),
empty the oil tank and put in a small amount of regular engine
oil (SAE 30),and then run the saw for a time. This is necessary
to flush out all remaining bio-degradable oil from the oil tank,
oil-feed system, chain and guide bar, as many such oils tend
to leave sticky residues over time, which can cause damage to
the oil pump or other parts.
-
Unscrew the tank cap (C/1) and fill in chain oil until it is on a
level with the bottom edge of the filler socket.
-
-
Tightly screw on the tank cap.
Thoroughly remove any oil that has overflown.
Important!
Before operating the saw for the first time, the oil feed system
must be completely filled, until the chain oil lubricates the chain
and guide bar.
The next time you use the saw, fill the tank with BIOTOP chain
oil again.
This procedure can take up to two minutes.
The next time you use the saw refill the tank with new BIOTOP
chain oil.
12
To guarantee a troublefree operation of the oil pump the oil
guide groove (E/3) as well as the oil inlet bore in the guide bar
(E/4) must be cleaned in regular intervals.
3
4
Note:
After the saw has been turned off it is normal for residual chain
oil to drip from the oil feed system, the guide bar and the chain
for a time. This does not constitute a defect!
Place the saw on a suitable surface.
E
Switching on the motor
5
6
7
F
G
-
-
Plug in the saw.
NOTE:
When switching on the electric chain saw always hold
it with both hands.
When the chain brake is actuated the power supply to the
motor will be cut off.
-
Take the back handle with the right hand and the tubular
handle with the left hand. Hold the handles tightly with your
thumbs facing your fingers. The bar and chain must not be
in contact with any object.
If the saw does not start when the ON/OFF switch (F/6) is
actuated, it will be necessary to release the chain brake.
-
Pull the hand guard (G/7) firmly in the direction of the arrow
until you feel it catch.
-
-
First depress the locking button (F/5) and then the power
switch (F/6). Then release the locking button (F/5).
IMPOTANT NOTE: Turning on machines causes transient
voltage dips. If the conditions of the power supply network are
unfavourable, there might be interference with other devices
on the same network. If the impedance of the network is lower
than 0,072 Ohms it can pressumed that no interference will
happen.
Attention: The chain starts running immediately. Keep
the power switch depressed as long as the motor is to run.
CAUTION:
Never lock the power switch in the ON position.
Switching off the motor:
-
Release the power switch (F/6).
Checking the chain brake
Do not work with the chain saw without first checking the
chain brake!
-
Start the motor as described (make sure you have a good
footing,andplacethechainsaw onthegroundinsuchaway
that the guide bar is free of contact).
7
-
-
Grasp the tubular handle firmly with one hand and hold the
grip with the other.
Switch on the motor and press the hand guard (H/7) in the
direction of the arrow with the back of your hand until the
chain brake engages. The chain should stop immediately.
-
Switch the motor off Immediately and release the chain
brake.
H
IMPORTANT: If the saw chain does not stop instantly
when you carry out this test, do not under any circum-
stances use the saw! Take the chain saw to a MAKITA
service center.
13
Testing the run-out brake
Do not work with the saw without first testing the run-out
brake!
-
Start the motor as described (make sure you have a good
footing, and place the chain saw on the ground in such a
way that the guide bar is free of contact).
-
-
Grasp the tubular handle firmly with one hand and hold the
grip with the other.
Switch the motor on and then back off. The chain should
come to a full stop within two second of switching off the
motor.
Important: If the saw chain does not stop within two
second when you carry out this test, do not use the
saw! Inspect the carbon brushes (see page 16).
I
Checking the chain lubrication
Neversawwhenasufficientchainlubricationisnotguaranteed.
Otherwise the life of the sawing device will be reduced. Before
starting work check the oil level in the tank and the oil feeding.
Check the fed oil quantity by following the instructions below:
-
-
Start the electric chain saw.
Hold the running chain saw approx. 15 cm above a trunk or
the ground (use an appropriate surface).
If the lubrication is sufficient, you will see a light oiltrace
becauseoilwillbecentrifugedfromthechainsaw.Payattention
to the direction the wind is blowing and avoid unnecessary
exposure to the oil spray!
J
MAINTENANCE
Sharpening the saw chain
When working on the saw chain you must always pull
out the power supply plug and wear protective gloves.
0.65 mm
(.025")
0.65 mm
(.025")
●
●
min.
3 mm (0.11”)
B
A
Proper sharpening:
CAUTION:
Use only chains and guide bars designed for this saw (see
the Extract from the spare-parts list)!
The chain needs sharpening when:
-
-
the sawdust from sawing humid wood looks like wood flour.
the saw chain penetrates the wood only under great
pressure.
-
All cutters must be of the same length (dimension a).
Cutters with different lengths result in rough running of the
chain and can cause cracks in the chain.
-
-
the cutting edge is visibly damaged.
-
Minimum cutter length is 3 mm (0.11"). Do not resharpen
thechainwhentheminimumcutterlengthhasbeen reached;
at this point, the chain must be replaced (see the Extract
from the spare-parts list and "Replacing the chain").
the sawing device is pulled to the left or the right during the
sawing operation. This is caused by uneven sharpening of
the chain or by damage to one side of it.
-
-
The depth of the cut is determined by the difference in
height between the depth limiter (round nose) and the
cutting edge.
The best results are obtained with a depth-limiter depth of
0.65 mm (.025").
Important: Sharpen frequently, but without removing
too much metal!
Generally, 2-3 strokes of the file will be enough.
Have the chain resharpened in a service center when you
have sharpened it yourself several times.
CAUTION:
Excessive depth increases the
risk of kickback!
14
C
D
-
-
All cutters must be sharpened to the same angle, 30°.
Different angles result in a roughly, irregularly running
chain, increase wear and tear and cause chain beakage.
Files and how to work with them
-
Sharpen using a special file holder with a saw chain round
file dia. 4.0 mm. Normal round files are not appropriate for
this work. See "Accessories" for the order number.
The 85° front rake of the cutter results from the cut depth of
the round file. If the proper file is used in the right manner,
the correct front rake will be obtained automatically.
-
-
-
The file should cut only when pushed forwards (arrow). Lift
the file when leading it backwards.
First sharpen the shortest cutter. The length of this cutter is
then the standerd for all other cutters of the chain.
Always guide the file as in fig. "D" shown
4/5
30°
E
F
G
-
The file holder makes file guidance easier. It is marked for
the correct 30° sharpening angle (keep the marks parallel
with the chain when filing, see illustration) and limits the cut
depth to the correct 4/5 of the file diameter. See "Accesso-
ries" for the order number.
-
After having sharpened the chain, the height of the depth
limiter must be checked by means of a chain gauge. See
"Accessories" for the order number.
-
-
Correct even the smallest excess height with a special flat
file (F). See "Accessories" for the order number.
Round off the front of the depth limiter (G).
Cleaning the guide bar,
lubricating the sprocket nose
CAUTION:
Protective gloves must be worn!
Regularly inspect the bearing surfaces of the guide bar for
damage, and clean them with a suitable tool.
If the saw is used intensively it will be necessary to lubricate the
return sprocket bearings regularly (once a week). To do this,
first thoroughly clean the 2 mm hole at the tip of the guide bar,
and then press in a small amount of multi-purpose grease.
Multi-purpose grease and grease guns are available as acces-
sories.
Multi-purpose grease
Grease gun
(order no. 944 360 000)
(order no. 944 350 000)
H
15
Replacing the saw chain
Inspecting and replacing
the carbon brushes
CAUTION: Use only chains and guide bars
designed for this saw (see the Extract from the spare
parts list)!
IMPORTANT:
Inspect the carbon brushes at regular
intervals! A notch on the brush shows the limit of wear.
1
A
B
C
2
3
NOTE:
Check the sprocket (A/1) before mounting a new chain.
Thecarbonbrushisverydelicate, sobecarefulnottoletitdrop.
When taking it out, be sure to note the position it was
installed in, since each brush is run in with the rotor.
CAUTION:
Worn out sprockets (B) may damage the new chain and must
therefore be replaced.
-
Use the combination wrench to unscrew the cover (C/2),
and then pull out the brush (C/3).
Do not attempt to replace the sprocket yourself. Sprocket
replacement requires special training and tools and must be
done at a MAKITA service centre.
-
If the wear limit has not yet been reached, put the brush
back in the same position and screw the cover (C/2) back
on.
-
Run the saw briefly (about a minute) so the brushes can run
in again.
IMPORTANT: Now test the run-out brake (see page 14). If the
saw chain does not come to a full stop within two second, run
the saw again briefly and repeat the test until the brake
functions properly.
SERVICE
NOTE: After installing new carbon brushes, run the saw about
5 minutes and then check the run-out brake.
Trouble shooting
Malfunction
System
Observation
Cause
electric motor does not function
no power supply,
cable defective
Chain saw does not work total
chain brake actuated
Mains fuse blown
insufficient performance
no chain lubrication
Carbon brushes
low pulling power
Carbon brushes worn down
no oil on the saw chain
Oil tank, oil pump
oil tank empty,
oil guide groove dirty
Chain brake
Brake
Brake
Brake band worn down
Saw chain does not stop instantly
Saw chain continues to run
Run-out brake
Carbon brushes worn down
16
Instructions for periodic maintenance
To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be
performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform
the prescribed maintenance work can lead to accidents!
The user of the electric chain saw is not allowed to perform maintenance works which are not described in the instruction manual.
All other works must be carried out by a MAKITA service centre.
Page
General work
Electric chain saw
Plastic case
Regularly clean the outside.
Check for cracks and ruptures. In case of damage have it
immediately repaired at a service centre.
Resharpen regularly.
Replace in time.
Turn over after a certain period of time so that the bearing
surfaces are uniformly worn.
Saw chain
Guide bar
Replace in time.
Sprocket
Chain brake
Run-out brake
Have it replaced in time at a service centre.
Have it inspected regularly at a service centre.
Have it inspected regularly at a service centre.
Each time before putting
the saw into operation
Saw chain
Check for damage and sharpness.
Check the chain tension.
14-15
11
Guide bar
Chain lubrication
Chain brake
Check for damage, and remove burrs if necessary.
Functional check.
Functional check.
14
13
14
13
Run-out brake
Power switch
Power supply cable
Oil tank cap
Functional check.
Functional check.
In case of damage have it replaced at a service centre.
Check for tightness.
After each shutdown
Storage
Guide bar
Chain carrier
Clean the oil inlet bore.
Clean, especially the oil guide groove.
13
15
Chain oil tank
Empty.
12
Saw chain/guide bar
Demount, clean and lubricate slightly.
Clean the guide groove of the guide bar.
Store safely in a dry place. After a long storage time, have
the electric chain saw checked at a service centre (resi-
dual oil can become resinic and the valve of the oil pump
clogged).
Electric chain saw
Service, spare parts and guarantee
Maintenance and repair
Themaintenanceandrepairworkofmodernelectricmotorsaswellasallsafetyrelatedassembliesrequirequalifiedtechnicaltraining
and the availability of a special workshop equipped with special tools and testing devices.
We therefore recommend you to consult a MAKITA service centre for the performance of all work not described in this instruction
manual.
TheMAKITAservicecentresareprovidedwithallthenecessaryequipmentandskilledandexperiencedpersonneltoworkoutcorrect
customer solutions and to advise you in all matters accordingly.
Please contact your nearest service centre (list enclosed).
Spare parts
A reliable and continuous operation as well as the safety of your chain saw is also subject to the quality of the spare parts used. Use
original MAKITA spare parts only, marked:
Only original spare parts and accessories guarantee the highest quality in material, dimensions, functioning and safety.
Original spare parts and accessories can be obtained from your local dealer. He will also have the relative spare part lists todetermine
the required spare part numbers, and will be constantly informed about the latest improvements and also about spare part
innovations.
Please, takeinmindthat inthecasethat foreignspareparts areusedinsteadof theoriginalMAKITA spareparts this willautomatically
invalidate the MAKITA product guarantee.
17
Guarantee
MAKITA guarantees the highest quality and will therefore reimburse all costs for mending through replacement of damaged parts as
a result of material or production faults, which occur within the guarantee time after purchase.
Please, note that in some countries particular guarantee conditions may exist. In case of any doubts, please, contact your salesman
who is responsible for the guarantee of the product.
We ask for your understanding that we cannot accept any responsibility for damage caused by:
•
•
•
•
•
•
•
•
•
•
•
•
Disregard of the instruction manual.
Non-performance of the required maintenance and cleaning instructions.
Normal wear and tear.
Obvious overload due to permanent excess of the upper limits of capacity.
Use of guide bars and saw chains which have not been approved.
Use of guide bar and saw chain lengths which have not been approved.
Use of force, improper use, misuse or accidents.
Damage caused by overheating due to dirt obstructing the cool air supply at the motor case.
Use of unsuitable spare parts or parts which are not original MAKITA parts, as far as they have caused the damage.
Use of unsuitable or old oil.
Damage related to conditions arising from lease or rent contracts.
Works on the chain saw by unskilled persons or performance of inappropriate repairs.
Cleaning, servicing and adjustment works are not covered by the guarantee. All repairs covered by the guarantee are to be performed
by a MAKITA service centre.
Extract from the spare parts list
Use original MAKITA spare parts only. For performance of repairs and for replacement of other
components your MAKITA service centre should be consulted.
Included in the delivery inventory
Accessories
(not included in the delivery inventory)
1
2
3
8
1
3
4
5
4
6
7
2
5
9
10
Pos. MAKITA No. Qty.
Denomination
3001A 3501A 4001A
Pos. MAKITA No.
Qty. Denominatio
1
2
3
4
5
953 100 090
953 004 010
953 003 090
953 003 060
953 030 010
1
1
1
1
1
Chain gauge 3/8”
File handle
Round file ø 4 mm
Flat file
1
2
3
4
5
6
7
7
7
8
8
8
9
205 114 201
901 505 354
001 213 042
923 208 004
225 213 100
957 802 410
442 030 661
442 035 661
442 040 661
528 092 646
528 092 652
528 092 656
952 100 633
1
1
1
1
1
2
1
1
1
1
1
1
1
1
Oil tank cap compl.
Screw for chain tightener
Nut with pin
Fastening nut
Sprocket guard
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
File holder compl. 3/8”
Carbon brushes
Sprocket nose bar 30 cm (12")
Sprocket nose bar 35 cm (14")
Sprocket nose bar 40 cm (16")
Saw chain 3/8" für 30 cm
Saw chain 3/8" für 35 cm
Saw chain 3/8" für 40 cm
1
1
1
1
1
1
1
Chain protection cover (30-40 cm)
Universal wrench SW 13
1
1
1
1
10 941 713 001
18
Space for your notes
19
Specifications subject to change without notice
Form: 995 704 113 (3.02 GB)
Makita Werkzeug GmbH
Postfach 70 04 20
D–22004 Hamburg
Germany
|