USE AND CARE MANUAL
FOR
INDUCTION COOKTOP
MODELS: CTI304D & CTI365D
THIS MANUAL SHOULD REMAIN WITH THE COOKTOP FOR
REFERENCE
Page# 1 of 16
11069.00 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1. Wear proper apparel. Loose fitting garments or those with long sleeves should never be worn
while cooking.
2. DO NOT TOUCH HOT COOKING UTENSILES OR THE IMMEDIATE AREA THAT WAS
UNDER THE COOKING UTENSLE. These areas may be hot. The glass surface heats because it
is in contact with the hot cooking vessel.
3. Use dry potholders only. Moist or damp potholders on hot surfaces may cause burns from steam.
Do not use towels or cloths in place of potholders.
4. This appliance is equipped with one or more surface units of different size. Always use utensils
that have flat bottoms. Use utensils that best match the surface unit size (smaller utensils on
smaller surface units) - and are a minimum of 4-inches in diameter.
5. UTENSIL HANDLES SHOULD BE TURNED INWARD AND NOT EXTEND OVER
ADJACENT SURFACE UNITS OR COUNTERS. To reduce the risk of INJURY, and spillage
due to unintentional contact with the utensil, the handle of the utensil should be positioned so that
it is turned inward, and does not extend over adjacent surface units or counter edges.
6. Never leave the cooktop unattended when heating elements are turned on. Boil over causes
smoking and greasy spillovers that may cause injury.
7. Use high heat setting only when necessary, and never when not monitoring the utensil. Use low to
medium settings to heat oil slowly.
8. Hold the handle of the utensil to prevent movement when stirring or turning food.
9. Do not use utensils that do not attract and hold a magnet and never use a steel plate or griddle to
heat a nonmagnetic utensil, which can cause INJURY or DAMAGE to the cooktop elements and
controls.
10. Clean the cooktop with caution. If soil must be removed while the cooktop is hot, clean the hot
top with a plastic spatula and then wipe with a dry cloth. DO NOT USE WET CLOTH OR
SPONGE WHILE THE COOKTOP IS HOT since steam can be generated if the cloth or sponge
is held in place on the hot spot. Some cleaners may produce noxious fumes if applied to hot
surfaces.
CAUTION – The cooktop is for cooking. Never use it to warm or heat a room.
Be sure your cooktop is properly installed and grounded by a qualified service installer in
accordance with local codes and the installation instructions provided with the cooktop.
Do not repair or replace any part of the appliance unless specifically recommended in the use
and care instructions. All servicing should be done by a qualified service technician.
Page# 3 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
11069.00 Rev A
OPERATING INSTRUCTIONS
BEFORE USING THE COOKTOP FOR THE FIRST TIME:
Be sure all packing materials, labels or tape are removed from the cooktop surface.
Wipe with a clean, damp sponge and dry.
Apply a Glass Ceramic Cleaning Crème. Buff with a clean cloth. (See CARE AND
CLEANING INSTRUCTIONS for glass top.)
Precautions to observe to preserve the cooktop appearance.
Regular use of the Cooktop Cleaning Crème on the glass surface will protect the surface
and make it easier to remove food soil and water spots.
The glass surface is resistant to impact but not unbreakable if a pan or other object is
dropped on it with sufficient force.
Do not use aluminum foil directly on the glass, it can melt and damage the glass.
Do not allow plastic to come in contact with a hot glass surface. They can melt or burn
and damage the glass surface.
Do not allow pans to boil dry. This can damage the pan, element and/or the cooktop.
Do not use the glass surface as a cutting board.
Do not slide utensils across cooking surface. This may cause scratching. Utensils with
rough surfaces should be avoided since they can scratch the glass surface.
Do not use griddle plates that bridge two or more elements (cooking zones). This can
damage the cooktop elements.
Signal Lights
POWER ON LIGHT (See Fig – 1)
The power on light will glow when one or more elements are turned on. The light is
located above each Turn-On touch pad.
POWER SETTING WINDOW (See Fig -1)
The number “0” appears and blinks when power is turned on.
The power level setting appears when selected.
Power levels are: L,1,2,3,4,5,6,7,8,9,H
NOTE: The power level selected will blink if a pan is not in place on the burner, and the
unit will turn off after 30 seconds if a pan is not in place on the burner.
SURFACE HOT LIGHT (See Fig – 1)
The light is located above the MED-Quick Select touch pad
The glass surface will be heated due to contact with the hot pan.
This light glows when the glass surface reaches a temperature that will feel warm or hot.
Page# 4 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
11069.00 Rev A
CTI304D
CTI365D
CONTROL
SETTING
SURFACE
HOT LITE
POWER
ON/OFF
LIGHT
BURNER
POSITION
INDICATOR
HI
MED
INCREASE
PRESS HERE
TO TURN ON
DECREASE
LOW
Fig - 1
Page# 5 of 16
11069.00 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Controls
See Fig – 1 for control locations and operation description. Each element has a control key-
pad array that is designated for use with it.. The key-pads are activated by placing your finger-
tip onto the pad area.
Note that pressing with high force is not necessary – pads are not pressure sensitive. The pad
is activated by your finger interrupting a localized electrical field.
NOTE: Spills or cleaning solutions on the control pads can cause unwanted control operation.
Simply dry the area with a clean cloth and reset the control to correct.
TURNING ELEMENTS ON
- Place pan on element selected, center for best operation.
- Locate “Turn-On” power pad operating the element selected and touch with finger. The
power light will turn on and the control power setting indicator will start blinking.
NOTE: If a power level is not selected, the power setting indicator will turn off after
approximately 30 seconds.
- Select the desired power level by using the “Quick-Select” pads (Hi-Med-Lo) or using the
“Increase/Decrease” pads. The power level selected will display in the power setting
Indicator window.
- You can change the power level setting at any time during the cooking process. - SEE Fig-2
FOR RECOMMENDED POWER SETTING LEVELS.
TURNING ELEMENTS OFF
- Turn off power by touching the “Turn-On” power pad. The power setting indicator window
will turn dark.
- OR simply remove the pan and the control will automatically shut off in 30 seconds.
CAUTION: If a pan is placed on the element before 30 seconds has elapsed the element
will turn back on.
Note: If a pan is not placed on the element when the” Turn-On” pad is touched the power
setting selected will be rejected and the power turned off. in 30-seconds.
Practice and experience will ultimately determine the heat settings most appropriate for you.
There will be some variation in the efficiency of the pots being used – all brands will not
behave in exactly the same way. Don’t be afraid to experiment and get your own comfort
level for using the cooktop. Once you experience the versatility, control and speed the
induction cooktop offers, you will never want to go back to conventional gas or electric
cooking.
You may want to make notations in your cooking references when you determine a setting
most appropriate for a particular food item. There is a blank table at the back of this manual to
note special food/power level settings.
Page# 6 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
11069.00 Rev A
Power Levels (watts)
Element Size
2200 WATT
2800 WATT
3600 WATT
Quick Select
LO
50
50
50
1
75
100
125
2
125
175
200
LO
3
200
275
350
4
275
375
475
5
400
575
700
6
525
725
7
8
9
HI
750 1300 1800 2200
950 1400 1800 2800
925 1200 1800 2600 3600
MED
HI
Cooking Condition
Power Setting
HI
Rapid Heat Up/ Rapid Rolling Boil
Low Level Rolling Boil
Frying
6 to 7
9 to HI
6 to 9
General Cooking or Browning
Simmer
2 to 5
Keep Warm *
1 to LO
*Caution: To Avoid Bacteria Generation Foods Should Be Maintained
Above 140º F.
Fig - 2
OPERATING INSTRUCTIONS
Temperature Limiters
All heating elements are equipped with a temperature limiter, for safety reasons. The limiter will
cycle the heating element, regardless of the control setting. This is normal and should not be cause for
alarm. But, the following may cause the cycling to be more frequent.
The bottom of the cooking utensil is not flat or is convex or concave.
The utensil/pan is too small in diameter for the element being used or the pan is not
reasonably centered.
Material of utensil/pan is poor heat conductor.
Utensil/pan is empty, ingredients have boiled away.
There is no utensil/pan on the element.
Page# 7 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
11069.00 Rev A
Cookware
The type of cookware used will affect performance. Pans must be magnetic.
Flat bottoms – utensils/pans with flat bottoms are best. Concave or convex bottoms will cause
uneven and slower heating. If pans are not stable (wobble), before or after heating, they will result in
slower and uneven cooking. Vibrations/buzzing can also be caused by the pans condition.
Size – Always try to center the pan on the element. Use smaller elements for smaller pans.
Covers – a cover or lid will reduce cooking times and prevent splashing.
Griddle Plates – Do not use griddle plates that cover more than one cooking zone.
CARE AND CLEANING INSTRUCTIONS
Caring for your cooktop is easy and its beauty will be preserved if you follow a few simple
maintenance techniques described in this section. Additionally some special cleaning methods are
also described.
Supplies
The following items will be useful in the maintenance of your glass surface.
Paper towels, sponge or cloth (avoid using soiled wipers)
Razor blade scraper – see Fig 3
Nonmetallic scouring pads (i.e.: Tuffy)
Glass ceramic cleaning crème
General cleaners (i.e.: Vinegar, Bon Ami)
Mild soap or detergent
A&H Baking Soda
The following will be useful in maintaining the painted discharge trim.
Clean damp cloth
Mild soap or detergent
Cleaners To Avoid
These type cleaners can discolor, scratch, stain, mark or etch the glass or painted trim.
Glass cleaners containing chlorine bleach or ammonia.
Caustic cleaners, such as oven cleaners.
Abrasive cleaners (i.e.: metal scouring pads, Scotch Brite sponges, S.O.S. pads)
Powder or liquid cleaners containing chlorine bleach or abrasives/cleaners.
Flammable cleaners.
Page# 8 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
11069.00 Rev A
General Cleaning Methods
Glass surface – Use a clean soapy sponge, paper towel or cloth to wipe off water or greasy
spatters. Rinse and wipe dry.
-Use vinegar if smudges or stubborn water spots are present.
-Use a paper towel pad soaked in a mild detergent solution to loosen baked on residue. Place
pad on the residue and let soak for approximately 20-minutes then wipe off. Repeat if
necessary.
-Use a clean paper towel with a small amount of Ceramic Glass Cleaning Crème applied to it
and rub onto the glass surface, let dry and buff with a clean dry towel.
- Stubborn stains/discoloration on glass, sprinkle a small amount of A&H Baking Soda (dry)
on the glass area to be cleaned and use your bare hand to gently rub in a circular motion.
Clean off the baking soda residue. Repeat if necessary.
- Use a razor blade scraper to remove badly baked on residue, See Fig-3. Always try using
one of the preceding methods before using the razor blade scraper.
Painted discharge trim – Caution: Do not use abrasive cleaners or pads. Using a mild soap
solution, wipe with clean cloth or sponge. Rinse and dry.
CAUTION: UNLESS OTHERWISE NOTED CLEAN SURFACE ONLY WHEN COOL.
CARE AND CLEANING INSTRUCTIONS
Special Cleaning Methods
The following applies to the glass surface only:
Sugar, syrup, tomato spills-REMOVEIMMEDIATELY/WHILE SURFACE IS HOT USE
PLASTIC SPATULA OR RAZOR BLADE SCRAPER ONLY-
USE DRY TOWELS OR SPONGES. WET TOWELS/SPONGES
CAN CAUSE STEAM BURNS
Remove utensil/pan from surface and turn control off. Angle scraper
slightly and push spill or residue off the heated surface. Don’t
scratch or gouge (Fig – 3). Let surface cool and remove residue,
apply Cleaning Crème.
This is the only clean up that is done with a hot surface!
Burned on food – Soften using a moist cloth or paper towel over the soil for 20 to 30 minutes.
Wipe clean, dry and apply Cleaning Crème.
Metal marks – Utensils/pans will occasionally leave marks. If Cleaning Crème does not remove
marks use mild cleanser (i.e.: Bon Ami) to remove. Rinse and dry surface and
apply Cleaning Crème. Magnetic stainless steel and porcelain coated steel/iron
pans are best. Uncoated cast iron pans can cause marking of the glass –
avoid sliding on the glass surface if possible.
Water spots – Apply undiluted white vinegar, rinse and dry. Apply Cleaning Crème.
Page# 9 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
11069.00 Rev A
Scratches – Cannot be removed. Avoidance is best, by using clean pans and removing spillage of
gritty foods. Keep top clean and apply Cleaning Crème often. Scratches will not
affect cooking capability.
Using The Razor Blade Scraper
Fig – 3
Page# 10 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
11069.00 Rev A
CTI304D
Page# 11 of 16
11069.00 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
CTI365D
Page# 12 of 16
11069.00 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Full One Year Warranty
Covers repairs and replacement of parts found to be defective due to materials and workmanship, for one year from the
date of purchase, or date of occupancy for new previously unoccupied dwelling.
Keep proof of purchase date or occupancy date available for inspection.
Warranty Service
Under terms of this warranty, service must be provided by a factory authorized service agency or representative, during
normal working hours. Labor performed at overtime or premium rates shall not be covered by this warranty.
FOR SERVICE, CONTACT THE FACTORY @ FACTORY SERVICE:
(877) 387-6721. ALL WARRANTY SERVICE MUST BE AUTHORIZED BY THE FACTORY.
Items Not Covered In Warranty
Damage or repairs due to service by an unauthorized agency or use of unauthorized parts.
Service visits to teach you how to use the appliance.
Service to correct installation related problems.
Service to reset circuit breakers or replace fuses.
Damage caused by abuse, accident, alteration, misuse or local code violations.
Failure due to other than normal family household use, or commercial use.
Service on products not purchased in country where service is to be performed.
Expenses for travel and transportation for product service in remote locations.
Warranty Application
This warranty applies to appliances used in residential applications only, not commercial use. The warranty is for
products purchased and retained in the 50 states of the USA, District of Columbia, and Canada. If the appliance is sold by
the original purchaser during the warranty period the new owner is protected until expiration of original purchasers
warranty. This warranty gives you specific legal rights. You may also have other rights, which very from state to state.
Warrantor is not responsible for consequential or incidental damage whether arising out of breach of warranty, breach of
contract, or otherwise. Some states do not allow exclusion or limitation of incidental or consequential damages, so the
preceding limitation or exclusion may not apply to you.
PRODUCT DATA
The data plate, showing the model and serial number, is located on the bottom of this unit. Record the model
and serial number, data of purchase, date installed, dealer’s name and address here for future
reference.
MODEL NO. ____________________________ SERIAL NO.
_______________________________
DATE OF PURCHASE ____________________ DATE INSTALLED
_________________________
DEALER’S NAME
___________________________________________________________________
ADDRESS
__________________________________________________________________________
Page# 13 of 16
Download from Www.Somanuals.com. All Manuals Search And Download.
11069.00 Rev A
NOTES
Page# 14 of 16
11069.00 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Page# 15 of 16
11069.00 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
CNP Industries, Inc.
P.O. Box 18645
Anaheim, CA 92817
(877) 387-6721 (714) 482-2337 Fax
Page# 16 of 16
11069.00 Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
|