Toshiba Projector Accessories TDP T95 User Manual

OWNER’S MANUAL

DATA PROJECTOR

TDP-T95

TDP-T100

Download from Www.Somanuals.com. All Manuals Search And Download.

Before Using

SAFETY PRECAUTIONS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended

to alert the user to the presence of uninsulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES

ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.

REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

Phone: (949) 583-3000

WARNING:

USA only

Changes or modifications made to this equipment, not expressly approved by

Toshiba, or parties authorized by Toshiba, could void the user’s authority to

operate the equipment.

WARNING: Handling the cord on this product or cords associated with accessories sold with

this product, will expose you to lead, a chemical known to the State of California

USA only

to cause birth defects or other reproductive harm. Wash hands after handling.

Notice:

CANADA only

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil

numérique de la classe B est conforme à la norme NMB-003 du Canada.

WARNING: This [product] contains mercury. Disposal of mercury may be regulated due to

environmental considerations. For disposal or recycling information, please

contact your local authorities or the Electronic Industries Alliance:www.eiae.org.

USA only

MODEL NAME: TDP-T95/TDP-T100

TRADE NAME: DATA PROJECTOR

MODEL NAME: TDP-T95/TDP-T100

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND

INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE

MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE

REFERENCE.

5. Heat

8. Power-Cord Protection

The product should be situated

Power-supply cords should be

routed so that they are not likely to

be walked on or pinched by items

placed upon or against them,

paying particular attention to cords

at plugs, convenience receptacles,

and the point where they exit from

the product.

away from heat sources such as

radiators, heat registers, stoves, or

other products (including

This unit is fully transistorized and does not contain any parts that can be repaired by the

user.

amplifiers) that produce heat.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO

DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL ONLY.

1. Read Owner's Manual

3. Source of Light

After unpacking this product, read

the owner's manual carefully, and

follow all the operating and other

instructions.

Do not look into the lens while the

lamp is on. The strong light from

the lamp may cause damage to

your eyes or sight.

6. Water and Moisture

Do not use this product near water.

- for example, near a bath tub,

wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a

swimming pool and the like.

9. Overloading

Do not overload wall outlets; to

reduce the risk of electric shock,

do not use the polarized plug with

an extension cord , receptacle, or

other outlet unless the blades can

be inserted completely with three-

wire grounding type to prevent

blade exposure. As this can result

in a risk of fire or electric shock.

2. Power Sources

4. Ventilation

This product should be operated

only from the type of power source

which does not exceed the voltage

range specified on the

rating label and the power cord.

If you are not sure of the type of

power supply to your home,

consult your product dealer or

local power company.

Openings in the cabinet are

7. Cleaning

provided for ventilation and to

ensure reliable operation of the

product and to protect it from

overheating, and these openings

must not be blocked or covered.

The openings should never be

blocked by placing the product on

a bed, sofa, rug or other similar

surface. This product should not

be placed in a built-in installation

such as a bookcase or rack unless

proper ventilation is provided.

Unplug this product from the wall

outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners.

Use a soft cloth for cleaning.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS (Continued)

e) If the product has been dropped or

damaged in any way (If the cabinet

should break, please handle with

care to avoid injury) .

f) When the product exhibits a

distinct change in performance -

this indicates a need for service.

10. Lightning storms

12. Do not place the product

vertically

15. Accessories

For added protection for this

product during storm, or when it is

left unattended and unused for

long periods of time, unplug it from

the wall outlet. This will prevent

damage to the product due to

lightning and power-line surges.

However, while it is thundering or

lightning, do not touch the

apparatus and any connected

cable and/or equipment.

This will prevent you from

receiving the electric shock by an

electric surge.

Do not place this product on an

unstable cart, stand, tripod,

Do not use the product in the

upright position to project the

pictures at the ceiling, or any other

vertical positions. It may fall down

and dangerous.

bracket, or table. The product may

fall, causing serious injury to a

child or adult, and serious damage

to the product. A product and cart

combination should be moved with

care. Quick stops, excessive

force, and uneven surfaces may

cause the product and cart

17. If glass components,

including lens and lamp,

should break, contact your

dealer for repair service.

combination to overturn.

This product incorporates glass

components, including a lens and

a lamp. If such parts should

break, please handle with care to

avoid injury and contact your

dealer for repair service. The

broken pieces of glass may cause

to injury. In the unlikely event of

the lamp rupturing, thoroughly

clean the area around the

13. Stack Inhibited

Do not stack other equipment on

this product or do not place this

product on the other equipment.

Top and bottom plates of this

product develops heat and may

give some undesirable damage to

other unit.

S3125A

16. Damage Requiring Service

Unplug this product from the wall

outlet and refer servicing to

qualified service personnel under

the following conditions:

11. Object and Liquid Entry

projector and discard any edible

items placed in that area.

Never push objects of any kind

into this product through openings

as they may touch dangerous

voltage points or short-out parts

that could result in a fire or electric

shock. Never spill liquid of any

kind on the product.

18. Servicing

a) When the power-supply cord or

plug is damaged.

b) If liquid has been spilled, or

objects have fallen into the

product.

c) If the product has been exposed to

rain or water.

Do not attempt to service this

product yourself as opening or

removing covers may expose you

to dangerous voltage or other

hazards. Refer all servicing to

qualified service personnel.

14. Attachments

d) If the product does not operate

normally by following the operating

instructions. Adjust only those

controls that are covered by the

operating instructions as an

improper adjustment of other

controls may result in damage and

will often require extensive work by

a qualified technician to restore

the product to its normal

Do not use attachments not

recommended by the product

manufacturer as they may cause

hazards.

operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS (Continued)

POWER SUPPLY CORD SELECTION

If your line voltage is 220 to 240V, use one of the following types of cable.

19. Replacement Parts

22. Do not use the product in

a closed installation state.

When replacement parts are

required, be sure the service

technician has used replacement

parts specified by the

manufacturer or have the same

characteristics as the original part.

Unauthorized substitutions may

result in fire, electric shock, or

other hazards.

Plug

Do not place the product in a box

or in any other closed installation

state. Otherwise it may overheat.

This could result in a risk of fire.

configuration Plug type

Line voltage

220 – 240V

configuration Plug type

Line voltage

200 – 240V

Australian

240V

10A

EURO

Switzerland 200 – 240V

240V

23. Do not look into the laser

light source of the remote

control or direct the laser

pointer toward a person or

a mirror.

220 – 240V

(Replacement of the lamp only

should be made by users.)

Use a 5A fuse which is approved by ASTA

or BSI to BSI362.

Always replace the fuse cover after

changing the fuse.

North American 200 – 240V

240V

15A

20. Safety Check

The laser beam may cause

damage to the eyes or sight.

Upon completion of any service or

repairs to this product, ask the

service technician to perform

safety checks to determine that

the product is in proper operating

condition.

IMPORTANT PRECAUTIONS

Save Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have to

ship your projector. For maximum protection, repack the set as it was originally packed at

the factory.

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location.

When the unit is exposed to such a change in temperature, moisture may condense on

the lens and the crucial internal parts. To prevent the unit from possible damage, do not

use the unit for at least 2 hours when there is an extreme or sudden change in tempera-

21. Do not leave thermal-

paper documents or easily

deformed items on top of

the unit or near the air

exhaust for long periods

of time.

ture

Place and Manner of Installation

• Do not place in hot locations, such as near heating equipment. Doing so could cause

malfunction, and shorten the life of the projector.

• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,

shortening their lives, and darkening the screen.

• Do not use this product in the upright position or tilt it up or down by more than 20° from

level. Doing so may cause a failure or shorten the life of the product.

• Using this instrument near a TV or radio may cause interference to the images or audio

sound. If this happens, move it away from the TV or radio.

The heat from the unit could erase

the information on the thermal

paper, or cause deformation or

warping.

• Moving the projector from a low-temperature room to a high-temperature room may

cause condensation on the lens or internal parts in the instrument. If you continue to use

it in that situation, the malfunction may result. Ensure to wait until the condensation

naturally disappears.

• In a high altitude location where air is thin, cooling efficiency is reduced so use the

p.40

projector with [Fan mode] set to [High].

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT PRECAUTIONS (Continued)

Avoid Volatile Liquid

Disposal

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or

plastic products touching the unit for a long time. They will leave marks on the finish.

If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.

This product contains substances which are harmful to humans and the environment.

• The lamp contains mercury.

Please dispose of this product or used lamps in accordance with local regulations.

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as

household waste. By ensuring this product is disposed of correctly, you will

help prevent potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate waste

handling of this product. For more detailed information about recycling of this

product, please contact your local city office, your household waste disposal

service or the shop where you purchased the product.

EXEMPTION CLAUSES

• Toshiba Corporation bears no responsibility in the case of damages arising from natural

disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, acts

by third parties, other accidents, or use under abnormal conditions including erroneous or

improper operation and other problems.

• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work

interruption, corruption or loss of the memory contents, etc.) arising from the use of or the

inability to use this unit.

• Toshiba Corporation accepts no liability whatsoever for any damages arising from not

having followed the descriptions in this Instruction Manual.

Trademarks

• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of

International Business Machines Corporation.

• Digital Light Processing, Digital Micromirror Device and DMD are trademakes of Texas

Instruments.

• Macintosh is a registered trademark of Apple Computer, Inc.

Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.

• Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems

Incorporated.

• Toshiba Corporation accepts no liability whatsoever for any damages arising from

malfunctions arising from combination with equipment or software that is not related to

Toshiba Corporation.

•

Notational Conventions Used in This Manual

• References to pages with related information are annotated as follows.

OTHER CAUTIONS AND INFORMATIONS

Copyrights

p.36

For example, if making a reference to page 36:

• The illustrations in this document are for reference purposes only and may not reflect

your package exactly.

Showing or transmitting commercial imaging software or broadcast or cable-broad casting

programs with the purpose of other than the personal and private viewing, including

modifying images using the freeze or resize functions, or displaying with the varying aspect

ratio of the images, could violate the direct or indirect copyrights of the imaging software or

broadcast program, etc., if done without first consulting with the copyright holder. For this

reason, please take appropriate measures before performing one of the actions listed

above, including obtaining a license from the copyright holder.

REMOTE CONTROL BATTERIES

Caution

• Never throw batteries into a fire.

Using the batteries improperly may cause them to explode or leak and lead to burn or injury. If

battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and consult a

doctor. If the fluid is spilt on an instrument, avoid contact and wipe it off using tissue paper.

(Dispose of the used tissue paper as flammable garbage after moistening with water.)

Notes

• Be sure to use AAA (LR03) size batteries.

• Dispose of batteries in a designated disposal area.

• Attention should be drawn to the environmental aspects of battery disposal.

• Do not mix different battery types or combine used batteries with new ones.

• If the remote control does not operate correctly, or if the operating range becomes

reduced, replace both batteries with new ones.

• If the batteries are dead or if you will not be using the remote control for a long time,

remove the batteries to prevent battery acid from leaking into the battery compartment.

In the spaces provided below, record the Model and Serial No. located at the bottom of your

projector.

Model No.

Serial No.

Retain this information for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

Before Using

Maintenance

About lamp......................................................................................................... 43

Lamp replacement ............................................................................................. 44

Lens and main unit cleaning .............................................................................. 46

SAFETY PRECAUTIONS ..................................................................................

IMPORTANT SAFETY INSTRUCTIONS ...........................................................

POWER SUPPLY CORD SELECTION..............................................................

IMPORTANT PRECAUTIONS ...........................................................................

EXEMPTION CLAUSES .................................................................................... 10

OTHER CAUTIONS AND INFORMATIONS ...................................................... 10

REMOTE CONTROL BATTERIES .................................................................... 11

CONTENTS ....................................................................................................... 12

Others

Trouble indications ............................................................................................. 47

Before calling service personnel ........................................................................ 48

Specifications..................................................................................................... 49

List of general specifications .......................................................................... 49

Separately sold product.................................................................................. 49

List of supported signals (RGB signals) ......................................................... 50

List of supported signals (Y/P^B/PR signals) .................................................... 51

List of supported signals (Video, S-Video signals) ......................................... 51

Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN &

Preparations

Checking the package contents ......................................................................... 14

Names of each part on the main unit................................................................. 15

Names of each part on the control panel and remote control............................ 16

Label locations ................................................................................................... 17

Names of the terminals on the rear panel.......................................................... 18

Preparing and using the remote control............................................................. 19

Operating a computer using the remote control ................................................ 20

Placement .......................................................................................................... 21

Connection......................................................................................................... 22

MONITOR terminals ....................................................................................... 51

CONTROL terminal ........................................................................................ 52

Operations

Turning the power on and off ............................................................................. 24

Basic operations ................................................................................................ 26

Using handy features ......................................................................................... 28

Using auto setting (Only for input from computer) .......................................... 28

Correcting the keystone distortion .................................................................. 28

Resizing image ............................................................................................... 29

Cutting off the picture and sound temporarily (Mute) ..................................... 30

Changing picture mode .................................................................................. 30

Changing screen size ..................................................................................... 31

Freezing the image (Freeze) .......................................................................... 31

Password function .......................................................................................... 32

Using the menus ................................................................................................ 34

How to use the menus .................................................................................... 34

The image adjustment menu .......................................................................... 35

The display setting menu................................................................................ 37

The default setting menu ................................................................................ 40

Displaying Information (Status display) .......................................................... 42

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparations

Checking the package contents

Names of each part on the main unit

Please make sure that the following items are included in the box, along with the main unit.

If any item is missing, please contact the store immediately where you purchased the

product.

(6)(5) (4)

(3) (2) (1)

(1)

(2)

(5)

(8)

(6)

(7)

(3)

(4)

(3)

(7)(8)

Back

(9) (10) (11)

(12)

(13)

(12)(14) (15)

Front

■ (1) Remote control

■ (6) Power cord ^{(See note)}

Name

: Function

■ (2) LR03 (SIZE AAA) batteries for remote ■ (7) Carrying bag

p.19

(1) Infrared remote sensor

(2) Foot adjuster release button : Press to set up or stow the foot adjuster.

(3) Air intake

(4) Control panel

(5) Zooming lever

(6) Focusing ring

(7) Antitheft lock hole

(8) Speaker

: Senses commands from the remote control.

control (2)

■ (8) Mouse remote control receiver

p.27

■ (3) CD-ROM

■ (4) Owner’s Manual

■ (5) RGB cable (3m)

: Draws in air from outside the projector.

p.16

: Operates the projector.

p.27

: Adjusts screen size.

p.27

: Adjusts screen focus.

Note

: Attach a safety cable or any other antitheft device.

The shape and number of supplied power cords vary depending on the product destination.

: Outputs audio sound.

p.18

(9) Terminals on the rear panel : Connects external devices.

(

10) AC IN socket

11) Air exhaust

12) Tilt adjuster

13) Lamp cover

14) Foot adjuster

15) Lens

: Connect the supplied power cord here.

: Expels air that has grown hot inside the projector.

◆The Supplied CD-ROM

p.27

The supplied CD-ROM contains an owner’s manual, including information not available for

: Adjusts the projector’s horizontal tilt.

the printed Owner’s manual (Getting started) and Acrobat^®Reader™ to view the manual.

: Remove to replace lamp.

p.44

p.27

: Adjusts the vertical projection angle.

■ Installing Acrobat^®Reader™

: Projects expanded image.

Windows^®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe.

Follow the on-screen instructions.

Macintosh: Run the CD-ROM, select the Reader/English folder, and run Reader

Installer. Follow the on-screen instructions to install the software.

■ Viewing the manual

Run the CD-ROM and double-click on Start.pdf. Acrobat^®Reader™ launches, and the

menu screen of the Owner’s manual appears. Click on your language. The Owner’s

Manual cover and list of bookmarks appear. Click on a bookmark title to view that

section of the manual. Click on

to view a reference page with related information.

See the Help menu for more information about Acrobat^®Reader™.

Download from Www.Somanuals.com. All Manuals Search And Download.

Names of each part on the control panel and remote control

Name

: Main Function

Control panel

Remote Control

p.28

(

13) AUTO SET button

14) Laser indicator

15) Mouse control button

16) PAGE+ button

17) MUTE button

18) FREEZE button

19) Ten-Key button

: Sets up analog input from computer.

: Lights when laser is on.

Remote control

transmitter

Warning label

(9) (10) (11)

Laser light

source

p.20

: Controls a mouse pointer.

: Proceeds PowerPoint slides.

p.20

(14)

(13)

(6)

(4)

(3)

p.30

: Cuts off the picture and sound temporarily.

(1)

(2)

(3)

p.31

: Pauses image.

(8)

(7)

: Use when entering password.

(12)

(26)

Battery

cover

(2)

(7)

(8)

Remote

control

button

Remote

control

button

Input

items

Input items

(6)

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[0]

(1)

(15)

(5)(4)

(25)

(24)

(23)

(22)

(16)

(17)

(18)

Deletes one character.

CAUTION

• Do not look into the laser light

source of the remote control or

p.20

(

20) Remote control ON/OFF switch : Switches on/off the remote control.

(21)

p.30

: Changes image mode.

21) PICTURE button

22) SCREEN SIZE button

23) RESIZE button

24) PAGE- button

25) R-CLICK button

26) L-CLICK button

direct the laser pointer toward a

person or a mirror.

p.31

: Changes screen size.

: Enlarges image.

(19)

(27)

p.29

• Handling and adjusting other than

described here may lead to

dangerous exposure to laser.

p.20

: Goes back PowerPoint slides.

: Functions as right-click of a mouse.

(20)

p.20

: Functions as left-click of a mouse.

27) Remote control code switch : Sets the code of remote control to that of the projector.

p.41

(inside the battery cover)

Name

: Main Function

Note

Control panel

• For the remainder of this manual, buttons are referred to as follows:

(1) ENTER button

(2) MENU button

(3) KEYSTONE button

(4) ON/STANDBY button

(5) ON/STANDBY indicator

(6) INPUT button

: Accepts the selected mode.

: Displays menus.

: Adjusts keystone distortion.

: Turns the power on/off (standby).

p.34

Selection buttons ⇒

; ENTER button ⇒

p.28

p.24

Label locations

p.24

: Displays whether power is on or off (standby).

p.26

: Selects input.

(7) RETURN button

(8) Selection button

: Goes back one screen.

: Menu selections and adjustments, volume control, etc.

p.34

p.25

(9) LAMP indicator

: Displays lamp mode.

p.47

(

10) TEMP indicator

11) FAN indicator

: Lights when internal temperature is too high.

: Displays cooling fan mode.

p.47

Remote control

(1) ENTER button

(2) MENU button

: Accepts the selected mode.

: Displays menus.

p.34

p.28

(3) KEYSTONE button

(4) ON/STANDBY button

(6) INPUT button

: Adjusts keystone distortion.

p.24

: Turns the power on/off (standby).

p.26

: Selects input.

(7) RETURN button

(8) Selection button

: Goes back one screen.

: Menu selections and adjustments, volume control, etc.

p.34

Caution – use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

(

12) LASER button

: Shows a laser pointer.

Download from Www.Somanuals.com. All Manuals Search And Download.

Names of the terminals on the rear panel

Preparing and using the remote control

(1) (2) (3) (4)

(5)

(6)

■ Loading dry-cell batteries

into the remote control

q Remove the battery cover.

■ Operating the remote

control

Turn on the ON/OFF switch of the

remote control.

Point toward the projector’s

infrared remote sensor, and press a

button on the remote control.

• Operating the projector from the front

w Insert the dry-cell batteries.

Be sure to align the plus and minus

ends of the batteries properly.

Approx. 15°

Approx. 5m

(7) (8)

(9)

(10)

Name

: Main Function

(1) CONTROL terminal

: When operating the projector via a computer, connect

When operating the remote control

from behind the projector, the laser

light is reflected on the projecting

surface and may travel a shorter

distance to reach the projector

depending on the shape and material

of the projecting surface.

p.52

this to the controlling computer’s RS-232C port.

Two batteries (LR03, SIZE AAA) are

used.

(2) MONITOR terminal

(3) AUDIO IN terminal

: Connect to a computer display, etc.

: Input audio signals from a computer, or from video

equipment with a component video signal output

terminal.

: Input RGB signal from a computer or other source, or a

component video signal (Y/P^B/PR) from video

equipment.

e Replace the battery cover.

(4) COMPUTER 1 IN terminal

(5) AUDIO (L/R) terminal

(6) S-VIDEO terminal

(7) AUDIO OUT terminal

(8) COMPUTER 2 IN terminal

: Input audio signals from video equipment.

: Input S video signals from video equipment.

: Outputs audio signals.

: Input analog RGB signal from a computer or other

source, or a component video signal (Y/PB/PR) from

video equipment.

Dry-cell batteries

• Before using the batteries, be sure to observe the Safety Precautions described in

previous pages.

• Remove batteries from remote control when not using for extended periods.

• If the remote control stops working, or if its range decreases, replace all the batteries with

new ones.

(9) AUDIO (L/R) terminal

: Input audio signals from video equipment.

: Input video signals from video equipment.

(

10) VIDEO terminal

The remote control

• Turn off the ON/OFF switch of the remote control when not in use or to store in baggage.

• The remote control may fail to operate if the infrared remote sensor is exposed to bright

sunlight or fluorescent lighting.

• Do not drop or bang.

• Do not leave in hot or humid locations.

• Do not get wet or place on top of wet objects.

• Do not take apart.

• In rare cases, ambient conditions could impede the operation of the remote control. If this

happens, point the remote control at the main unit again, and repeat the operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating a computer using the remote control

Placement

A computer can be operated using the projector’s remote control. This function is available

on any computer with the Windows^®98/98SE, Windows^®Me, Windows^®2000, or Win-

dows^®XP OS, that is equipped with a USB port which can support USB1.1 (The mouse

remote control receiver is also supported on OS 9 or OS X for the Macintosh). However,

please note that Toshiba does not guarantee the operation of all computers.

Placement Styles

As shown in the figures below, this device can be placed in 4 different styles.

The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the

p.40

Default setting menu

, in accordance with your needs.

Floor-mounted front projection

Floor-mounted rear projection

Connecting a computer

Connect the mouse remote control receiver (supplied) to a computer.

The remote control may fail to operate

if the mouse remote control receiver is

exposed to bright sunlight or

fluorescent lighting.

To USB port

Ceiling-mounted front projection

Ceiling-mounted rear projection

In such a case, change position or

direction of the mouse remote control

receiver and retry.

Mouse remote control receiver

Operating a computer

Operate remote control’s buttons towards the mouse remote control receiver.

● Moving the mouse pointer

Press the mouse control button in the direction you wish the mouse pointer to move,

then press.

● To left click

WARNING

• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.

Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus

resulting in injury.

• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the

projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.

Improper mounting could cause the projector to fall, resulting in an accident.

• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let

everyone involved with the use of the projector know that fact.

Press the L-CLICK button.

● To right click

Press the R-CLICK button.

● To drag and drop

Projection Distance and Size

Use the figures, tables, and formulas below to determine the projection size and projection

distance. (Projection sizes are approximate values for full-size picture with no keystone

Holding down the L-CLICK button, move the mouse control button until the mouse

pointer is over the desired location, then release the L-CLICK button.

● Using the computer’s page up [ ] and down [ ] function

↑

↓

adjustment.)

Press the PAGE+ and PAGE- buttons to switch PowerPoint^®slides.

Remote Control Front Remote Control Rear

projection size (inches) – 1.0437

a (min length) =

Screen

26.957

As seen from above

projection size (inches) – 0.6246

16.749

a (max length) =

90°

projection distance a (m)

projection

Mouse control

L-CLICK

min length

max length

size (inches)

(zooming max) (zooming min)

As seen from the side

1.07

1.45

2.19

2.93

3.67

5.53

7.38

9.24

11.09

1.75

2.35

3.55

4.74

5.93

8.92

–

PAGE –

R-CLICK

PAGE +

Lens center

100

150

200

250

300

90°

–

a is the distance (m) between the lens and the screen, and

corresponds to a range of 1.07 m to 11.09 m.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connection

Notes

Before connection

• The COMPUTER 1 IN terminal functions identically to the COMPUTER 2 IN terminal.

• The MONITOR OUT terminal outputs signals from the COMPUTER 1 IN terminal or the

COMPUTER 2 IN terminal, or outputs Y/P^B/PR as selected with the INPUT button. If no

input is selected, the MONITOR OUT terminal outputs the input signals last selected for

each input terminal

• Read the owner’s manual of the device you are connecting to the projector.

• Some types of computer cannot be used or connected to this projector.

p.50

Check for an RGB output terminal, supported signal

• Turn off the power of both devices before connecting.

, etc.

• The figure is a sample connection. This does not mean that all of these devices can or

must be connected simultaneously. (Dotted lines mean items can be exchanged.)

• Signals are output from MONITOR OUT terminal even in standby mode.

However, from AUDIO OUT terminal, no audio signal is output.

Computer

(for control)

Video recorder,

DVD player, etc.

• A computer monitor cannot accept Y/PB/PR signals correctly.

Computer

• The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2.

• When an AUDIO OUT terminal is connected, sound is not output from the projector

speaker.

• Output volume of AUDIO OUT terminal can be adjusted by the VOL button.

• Moving pictures played back on computers using DVD software may appear unnatural if it

is projected with this projector, but it is not a malfunction.

To audio

output

White (L)/

Red (R)

To S-video

output

RS-232C

terminal

To audio

output

Audio cable

(not supplied)

To RGB

output

p.52

To audio

output

Audio cable

(not supplied)

To RGB

output

RGB cable

(not supplied)

RGB cable

(supplied)

S-video cable

(not supplied)

Control cable

Audio cable

(not supplied)

Audio cable

(not supplied)

Monitor cable Mini

D-sub 15P-BNC

(not supplied)

Audio cable

(not supplied)

To Y/CB/CR

output

Green (Y)/Blue

AV cable

(not supplied)

To audio

output

(CB)/Red (CR

)

To audio input

White (L)/Red (R)

Conversion

adapter BNC-pin

(not supplied)

To audio output

White (L)/Red (R)

To video

output

Audio amplifier, etc.

DVD video recorder, etc.

Video recorder, etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operations

Turning the power on and off

Notes

■ Connecting the power cord

• The start-up screen will disappear after a moment.You can dismiss the start-up screen

Insert the power cord connector into

the AC IN socket of the projector.

before this by performing any operation.You can also configure the start-up screen not to

p.37

appear via the Display setting menu

• The first time you use the projector after purchase, after the start-up screen disappears,

Insert the power cord plug into a

wall or other power outlet.

p.26

the start menu is displayed

Power cord connector

(Supplied)

p.41

• When [Key lock] is [On], the operation buttons of the projector do not work

• When [Password] is [On], enter password then the start-up screen is displayed after the

The ON/STANDBY indicator will

change to orange, indicating standby

mode.

p.32

Password entry screen disappears

■ Turning the power off

Press the ON/STANDBY button.

A message appears on the screen, confirming that you wish to shut off the power. This

message will disappear after a moment. (This operation is no longer valid after the

message disappears.)

■ Removing the lens cover

Be sure to remove the lens cover when the power is

turned on. If it is left on, it could become deformed due

to heat.

Press the ON/STANDBY button again.

The screen turns off, but the internal cooling fan continues to operate for a short while.

Then, the projector goes into standby mode.

When cooling lamp

During internal cooling

After cooling complete

Remote

Control

■ Turning the power on

Press the ON/STANDBY

button.

Control panel

Start-up screen

During cooling, the LAMP indicator flashes. In this state, the power cannot be

turned back on.

If you are in a hurry, there is no problem with unplugging the power cord in this

state.

The power turns on, and the following

3 green indicators light: ON/STANDBY,

LAMP, and FAN. After a moment, the

start-up screen appears.

After the LAMP indicator goes off, the FAN indicator keeps lighted and the

cooling fan continues to operate for a short while, in order to expel excess

internal heat.

CAUTION

In standby mode

• Do not look into the lens while the lamp is on. The strong light from the lamp may cause

damage to your eyes or sight.

• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.

• Do not place your hands, face, or other objects near the air exhaust. Doing so could cause

burns, deform/break the object.

Note

• The projector consumes about 9W of power in standby. We recommend that you unplug

the power cord if you will not be using the projector for an extended period.

PRECAUTION

• If the power cord is unplugged before cooling is complete, give the lamp time (about 5

minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.

Download from Www.Somanuals.com. All Manuals Search And Download.

Basic operations

Turn on the power.

Turn on the power by following the instructions in “Turning the power on”

Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot

adjuster.

p.24

Select the language and the lamp power (When using the

first time).

q Lift up the front of the projector to

the desired angle, then press the

foot adjuster release button.

The foot adjuster extends. Release the

button to lock the position.

When the projector is used for the first time after purchase, the start menu for lan-

guage (to display the menus and messages on the screen) and lamp power selection

and configuration is displayed in English. (If the screen is out of focus, adjust it

according to the step .)

w To fine adjust the angle, twist the

foot adjuster.

q Use the

button to select the

button.

English

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Turkish

desired language and press the

e To adjust the horizontal angle, use

Message for setup confirmation is displayed in a

selected language.

Then, the menu for lamp power selection and

configuration is displayed. It is automatically set as

Standard. To change the setting, follow the step w.

the right and left tilt adjusters.

• To stow the foot adjuster, hold up the projec-

tor while pressing the foot adjuster release

button, then slowly lower the projector.

Polish

w Use the

power and press the

The lamp power, if selected, will be toggled without

pressing the button. The display automatically

button to select the lamp

Adjusting the screen size and focus

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

button.

Use the zooming lever to adjust the screen size.

w Use the focusing ring to adjust the focus.

disappears in a few seconds.

Adjusting the volume with the

The speaker volume can be adjusted when an audio signal is being input.

buttons

Notes

• When the projector is turned on the next time, the start menu does not appear upon

p.40

startup. However, if [Reset all] is executed from the Default setting menu

start menu will be displayed the next time when the power is turned on.

, the

Notes

• Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.

• A lamp is consumable item. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The

lifetime of the lamp depends on conditions of use.)

p.37

• The language can also be set via the Display setting menu

and Lamp power

p.40

via the Default setting menu

• This owner’s manual assumes that English has been selected.

• The DMD^TMis made using extremely advanced technology, but there may be black spots

(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please

note that these are not malfunctions.

Activate the connected device.

Turn on and start the connected device such as a computer.

p.50

• Although this projector supports a wide range of RGB signals

, any resolutions not

Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected

supported by this projector (XGA) will be expanded or shrunk, which will affect image

quality slightly. To view high-quality images, it is recommended that the computer’s

external output should be set to XGA resolution.

• With some models of computer having LCD displays or the like, displaying images

simultaneously on the projector and the monitor’s display may prevent the images from

displaying properly. If this happens, turn off the computer’s LCD display. For information

on how to turn off the LCD display, see the owner’s manual of your computer.

• If no signal is being input from the connected equipment or signal input is stopped while

projecting, the “No signal” will appear.

equipment that is outputting video signals.

Notes

p.40

• When [Auto input search] is set to [Off] in the Default setting menu

setting is [On]), the Switch input menu appears if you press the INPUT button

• If no signal is being output from the connected equipment, pressing the INPUT button

does not change the input and “There is no other input signal.” will appear.

(factory

p.40

• If a signal not supported by the projector is input, the “Unsupport signal” will appear.

• If an unavailable operation button is pressed, the

icon will appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using handy features

Adjusting Keystone distortion [Auto]

■ Using auto setting (Only for input from computer)

Remote

Control

This function sets up the projector to the optimum state such as

sampling phase, frequency, screen position, and clamp for each

type of the input signal by using simple operations.

Press the

button.

The keystone distortion is automatically corrected. The

correction.

icon appears during this

When adjustment is finished, the Keystone menu appears again. For fine adjust-

Press the remote control’s AUTO SET button.

ment, select [V-keystone] by the

button and adjust image manually by the

For computer input, the

icon will appear during processing.

buttons.

You can set as well by selecting [Auto setting] in the Image

p.35

adjustment menu

Adjusting Keystone distortion [Manual]

Press the KEYSTONE button.

Select [V-keystone] by the

Notes

button.

• The image may not be projected or auto adjustment/setting may not be performed

correctly for input signals other than those supported by the projector

• If auto setting fails adjustment, adjust manually with [Position] in the Image

adjustment menu

p.50 p.51

Use the

buttons for keystone adjustment.

p.35

Note

• Depending on the amount of keystone adjustment and the content of images, some

information may be lost, or the picture quality may suffer.

■ Correcting the keystone distortion

Remote

Control

When the projector placement angle against the

screen is changed while projecting the image,

the picture will undergo keystone (trapezoidal)

distortion.

Control panel

■ Resizing image

The projected image can be resized (zoomed in/out).

Press the remote control’s RESIZE

button.

This projector is capable of correcting this keystone

Each time you press the RESIZE

pressing.

button, zoom ratio is up.You can keep

distortion

Before correction After correction

Remote

Control

To zoom out, press the remote control’s RESIZE

button.

Press the KEYSTONE button.

The Keystone menu appears. By default, [Auto v-keystone] is selected.

Each time you press the RESIZE

down.You can keep pressing.

button, zoom ratio is

(However, the image cannot be smaller than the original

size.)

Item

Description

Automatically corrects the vertical distortion.

Auto v-keystone

Press

Screen shrinking at

bottom

Screen shrinking at

top

V-keystone

To move the area to zoom in, use the

buttons.

You can keep pressing.

To reset the zoom, press the RETURN button.

The image is reset to the original size.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using handy features (Continued)

Notes

• The

■ Changing screen size

icon appears while resizing.

Remote

Control

The screen size for the projected image can be changed.

• Operating a function other than Mute will release resizing.

• As zooming is processed digitally, the image quality is degraded in larger zoom

ratio.

Press the remote control’s SCREEN SIZE button.

Pressing the button switches Full/Thru/Wide in turn.

• During resizing or moving the zooming area, the image may be distorted.

Notes

• Thru display is available for computer-input images.

■ Cutting off the picture and sound temporarily (Mute)

• [Screen size] of the Display setting menu has the same function

p.37

Remote

Control

When you want to project the images of another projector, overhead

projector, etc. temporarily, this projector’s images and sound can be

turned off.

• If you use this function on commercial video software, broadcast

or cable-broadcasting except for the purpose of your private

viewing and listening, it may infringe the copyright protected by

the copyright laws.

Press the remote control’s MUTE button.

The picture and sound are cut off. (The Mute function is released

when pressing the MUTE button again.)

■ Freezing the image (Freeze)

Notes

Remote

Control

The image being projected can be frozen. This function is to be used

to pause a video during a presentation, etc.

• The

icon will appear while mute is in effect.

• Operating any other functions will also cancel the muting.

Press the remote control’s FREEZE button.

The picture pauses. (The Freeze function is released when

pressing the FREEZE button again.)

■ Changing picture mode

Remote

Control

The projected image mode can be selected.

Notes

Press the remote control’s PICTURE button.

• The

icon will appear while freeze is in effect.

The Picture mode menu appears.

• Other operation will also release the freeze.

• Even if an image is frozen on the projector, the pictures are

running on the video or other equipment.

When connected with computer 1/2/3/4/5

When connected with video equipment 1/2/3

Select a mode using

then press

• If you use this function on commercial video software, broadcast

or cable-broadcasting except for the purpose of your private

viewing and listening, it may infringe the copyright protected by

the copyright laws.

Though the button is not pressed, the picture mode

changes as the setting is changed and the display turns off

automatically in a few seconds.

Note

• [Picture mode] of the Image adjustment menu has the same

p.35

function

Download from Www.Somanuals.com. All Manuals Search And Download.

Using handy features (Continued)

How to cancel password (from [On] to [Off])

■ Password function

When the password function is added and [Password] is set to [On], image projection

requires an entry of the preset password at power-on.

Select [Password] in the Default setting menu and press the

button.

To add the password function, perform the following procedure:

(The password function, once added, cannot be deleted. Set [Password] to [Off] if you

do not want to use it after addition.)

The password entry screen is displayed.

Enter the password using numeric keys of the remote control.

The password cancel confirmation screen is displayed. ([OK] or

[Cancel])

How to add password

Set the projector to the operating status or the standby mode.

Select [OK] and press the

button.

Select and hold the button until the LAMP, TEMP, and FAN

The [Password] is canceled and becomes [Off].

indicators light in orange.

The password function is added when the steps up to here have been completed. It

is also added to the Default setting menu.

Note

• The password entry screen appears when the power is turned back on only after

the power cord is unplugged.

How to set password (from [Off] to [On])

Select [Password] in the Default setting menu and press the

button.

You cannot release password by yourself. If you forgot password,

please inquire your dealer.

The password setting confirmation screen is displayed. ([OK] or [Cancel])

Select [On] and press the

The password entry screen is displayed.

button.

Enter a four-digit number for the password using numeric keys of the

remote control.

The input number appears as [****].

Re-enter the same password for confirmation.

When the password is confirmed, the setting is complete and the password

becomes [On].

If the password is wrong, repeat the procedure from step

How to operate when password is [On]

Turn on the power.

The lamp lights and the password entry screen appears.

Enter the password using numeric keys of the remote control.

If the entered password is correct, the start-up screen appears and the projector

goes into normal operation. If the password is wrong, a message appears to

prompt you to re-enter the password, and again the password entry screen is

displayed. If you enter a wrong password for more than 5 times, the projector will

automatically power off and enter standby mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menus

You can call up on-screen menus, and conduct a number of adjustments and settings using

■ The image adjustment menu

Use this menu to set or adjust image-related items. Items that can be set or adjusted are

marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,

it indicates that you cannot select for the current input.)

p.16

the operation buttons

on the control panel (main unit side) and remote control.

■ How to use the menus

The menu shown below is for operation instructions purposes and might differ from the

actual display.

Item

Description

Computer Y/PB/PR Video S-video

Contrast

Adjust the image contrast.

Lower

Yes

Display the Setting display menu.

1. Press the MENU button

2. Select a Category

Higher

Brightness

Color

Adjust the brightness of the image.

Darker Brighter

Select a category by using

Displays the current

adjustments and

settings of selected

category.

Item shown with gray

cannot be adjusted with

the current input source.

There are following four

categories:

Adjust the color of the image.

Lighter

Deeper

p.35

Image adjustment menu

Sharpness

Adjust the sharpness of the image.

Softer

Sharper

p.37

p.40

p.42

Display setting menu

Default setting menu

Status display menu

Noise

reduction

Set the function to reduce screen noise.

On (Enable)

Off (Disable)

Picture mode Press

. Toggle the picture mode with

1/2/3

1/2/3/4/5

Adjust red of the image color.

Less red More red

Adjust green of the image color.

Yes

3. Adjustments & Settings

Press

to open the menu.

R-level

G-level

B-level

Yes

Item

These marks

signify that

there are setting

screens. Press

Adjustment/Setting Value

Yes

Less green

More green

These marks signify

the items can be

adjusted/set by using

Adjust blue of the image color.

display a list of

setting screens.

These marks

signify that there

are options.

Press

to display a list of

options.

Less blue

More blue

NTSC mode^*2Set the black level with

JAPAN

NTSC (US) mode

NTSC (JAPAN) mode

Auto setting

Position

Automatically adjusts items such as the sampling

phase depending on the type of input signal.

Yes

* When no item is

changed, press

These marks signify the items can

be selected from the list by using

Press

adjust with

then change mode using

and

After an item is selected, apply it by

Toggle items with

Select items with

Fix selection with

pressing

and press

Phase

Adjust to eliminate flicker.

•

The figure shows displays given for operation instructions purposes. As the display may differ depending on the item,

use the following pages as a reference.

Frequency

Adjust to eliminate periodic patterns and flickering

when many fine vertical lines appear on the screen.

To return to previous item, press the RETURN button.

H-position

Adjust the horizontal position of the image.

Yes

4. End Press the MENU button.

(The menu disappears 30 seconds after the last operation.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menus (Continued)

■ The display setting menu

Item

Description

Computer Y/PB/PR Video S-video

Use this menu to set screen display-related items.

(The items in gray color cannot be set with the current input selection.)

Position

V-position

Adjust the vertical position of the image.

Yes

Clamp 1

Adjusts the clamp pulse position.

Description

Item

Screen size

Clamp 2

(Full): Display with 1024 × 768 dot resolution

(Thru): Display with sampling resolution (for computer input only)

(Wide): Wide-screen display

Adjusts the clamp pulse width.

*1: [Noise reduction] may not work depending on signal type.

*2: [[NTSC mode] can be displayed and adjusted only when the video signal is set to [NTSC] or

When projecting on a non-screen surface, select a color in accordance

with the projecting surface.

[NTSC4.43]. NTSC mode is set to JAPAN when the language is set to Japanese. It is set to US for

Blackboard

mode

other languages.

Press

and switch with

and

Off/Green/Black/Brown/Blue/Beige

Select one of the languages below to use for displaying the menu and messages

Language

[

English/Français/Deutsch/Italiano/Español/Português/

Svenska/Türkçe/Polski/

Screen to display when there is no input signal

or : Enter setting mode] :Selection]

: Enter setting mode]

[

:Selection]

[Apply:

]

Background

Icon

[

[Apply:

Logo/Blue/None

Display icons as function guides

Off

Start-up screen Display start-up screen when power is turned on On

User logo

Display a logo customized by the user for the start-up screen or when

there is no input signal.

[

: Enter setting mode]

[

: Selection]

Logo registration

Display style

Background

Press

to display the registration menu.

Black

Blue

White

Logo confirmation Press

Reset logo Yes

Detailed description

[Screen size]

• If “Thru” is selected for [Screen size], portions exceeding the native resolution

(1024 × 768 pixels) will not appear on the screen. Note that for RGB signals with

clock frequency 140MHz or lower, all input pixel signals are sampled. However, if

the clock speed is higher than this, the RGB pixel signal is thinned before

sampling.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menus (Continued)

Note

Notes

• If you use the screen size setting function on commercial video software,

broadcast or cable-broadcasting programs to display images with the varying

aspect ratio except for the purpose of your private viewing and listening, it may

infringe the copyright protected by the copyright laws.

• You can register a logo from computer input only.

• The area that can be registered is 512 × 384 dots at the center of the screen. To

• Only one logo can be registered. When a new image is registered, the old one is

erased.

• The time needed to register or display the image varies depending on the data size.

• If you use this function on commercial video software, broadcast or cable-

broadcasting except for the purpose of your private viewing and listening, it may

infringe the copyright protected by the copyright laws.

[Blackboard mode]

Projects the image in colors more like projecting on a screen.

Precaution

• The projected image may differ depending on the type, color, and material of the

blackboard and wall even if the selected color is the same as the projected

screen.

[Background]

Select the size of the registered logo.

• TOSHIBA is set for [Logo] by factory setting.

• If user’s logo has been registered, it is displayed when [Logo] is set for

background.

: Displays the registered image in original size at center of the screen.

: Displays the registered image by enlarging fully in the screen.

(As processed digitally, the image quality is degraded.)

[Start-up screen]

If user’s logo has been registered and this setting is [On], the logo is displayed at

start-up.

[User logo]

Sets background color when [Center] is selected for the logo [Display style].

Registers a part of the image that is input from computer, as a stationary picture

and displays it as a logo at start-up and when no signal is input.

You can preview the registered logo.

How to register user logo

You can reset the registered logo, display style and background to the factory

setting. (The logo set for the start-up screen and background is reset.)

Select [User logo] in the Display setting menu, and press the

or button.

Select <Logo registration> from the displayed menu list and

press the button.

The registration area is displayed for confirmation. Select [OK]

or [Cancel] and press the button.

• If the registered picture does not fall within the display area, operate the

computer to scroll the screen.

Select [Yes] to register and press the

button.

Registration starts.

• A message is displayed while registration is in process.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the menus (Continued)

[Power on]

■ The default setting menu

This menu shows placement status and other settings.

Note that if [Power on] is set to [Auto], then if the power is supplied when restored

after a power outage, the projector will come on.

Description

Sets projection mode in accordance with Placement Style.

Item

[Lamp power]

p.21

Projection

mode

When [Lamp power] is set to [Low], the screen becomes a little darker, but the

cooling fan noise gets quieter.

(Standard)

(Rear)

(Ceiling)

(Rear ceiling)

No signal

power off

Set the time to wait for the power to be turned off after the last

operation is made with no input signal.

[Fan mode]

Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan

noise gets louder.) Set this option to use the projector, for example, at high altitude

(over 1,500 meters above sea level).

Off (not turned off)

30 min.

Auto input

Set whether the input with signals is only selected or not.

Sets whether to turn on the power when the ON/STANDBY button is pressed

Off

• Do not set Fan mode to [High] when using the projector at a lower altitude.

Power on

[Remote control]

(Manual), or when the power cord is plugged in (Auto).

Manual

Low

Standard

Auto

Sets a remote control code from 4 types.You can set each code respectively for up

to 4 projectors. The factory setting is [1].

To switch codes, set the same code for the projector and the remote control.

A remote control code is applied after the setting is done.

• You cannot operate the remote control if the codes of the projector and the

remote control do not match.

Lamp power

Fan mode

Sets the lamp power.

Standard

High

Sets the cooling fan speed.

Remote control

When two or more projectors are used and controlled by the remote

control respectively, this menu sets the code for the projector and the

remote control.

Remote control code setting for remote control

[

: Enter setting mode]

[

: Select item]

[

Select from 1, 2, 3, 4]

Press [Cancel] to return.

[

:Confirm]

[ :Select OK to end]

Remove the battery cover and set the same remote control code switch as the

p.16

projector.

(Use a screwdriver with thin tip to set.)

Key lock

Lock the control panel buttons.

or : Enter setting mode]

Select On/Off] :Confirm]

Press [Cancel] to return.

[

: Select item]

[

:Select OK to end]

[Key lock]

Reset all

Press . (The password and user logo are not reset.)

Resets all adjustments and settings to their factory settings.

Protect from operating errors by locking on the control panel buttons of the

projector. (The remote control operations are available.)

Control panel operations are locked after the setting is done, and accordingly

operation with the control panel buttons is disabled.

Yes

Off

Password

Password function

p.32

When [Password] is [On], the Password Setting screen is displayed.

• To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing

the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to

[Off]. (In the latter case, the LAMP, TEMP, and FAN indicators light in orange for 3

seconds.)

Detailed description

[Auto input search]

Input select menu

Input select

Computer 1

Y/P^B/PR

Computer 2

[On]: Automatically searches the signals that

can be projected, and switches input

from the connected device that outputs

the video signals each time the INPUT

button is pressed. The input from the

connected device that outputs no video

signals is skipped.

Y/P^B/PR

Video

S-video

shows whether signal is

input or not.

[Off]: Displays the Input select menu.

Toggle with

button. (The input without signals can be

buttons and press

selected.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Maintenance

Using the menus (Continued)

About lamp

The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure

to fully understand the following characteristics of the lamp and handle it with extreme care.

• The lamp may burst with a loud noise due to impact or deterioration, or fail to light at

the expiration of its life.

• How long it takes before the lamp bursts or the life expires may vary greatly by lamp.

Some may burst shortly after first use.

• Burst is likely to happen if the lamp is used after the replacement period has elapsed.

• When the lamp bursts, the broken pieces of glass may get inside the product or be

released outside from the openings for ventilation.

• When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with

glass dust may be released from the openings for ventilation.

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

Item

Projector

Description

Computer Y/PB/PR

Video

S-video

Input

Input source name

Yes

Mode name

Resolution

Frequency

Sync

Signal format

Video mode

Lamp time

RGB input mode ^{[Note 1]}

Resolution (in dots)

Sync frequency

Sync signal polarity ^{[Note 2]}

Y/PB/PR signal format

Color method of video signal

Time of lamp use ^{[Note 3]}

■

Immediately replace the lamp when a sign appears on the screen.

• When the replacement time approaches, a message will appear on the screen.

• The risk of burst will increase if the lamp is continuously used without being replaced.

• Frequently check the used hours and prepare spares when the replacement time

Yes

approaches. (Refer to “Status display”. p.42

)

Lamp reset count The count for lamp replacement

Total time

Version

The total time that this projector is

used.

■

When the lamp is broken

Yes

• If glass components, including a lamp and a lens, should break, handle the broken

pieces with care to avoid injury and contact your dealer for repair service.

• In the event of lamp burst, unplug the product from the wall outlet, leave and completely

ventilate the room. Then, thoroughly clean the area around the projector and discard

any edible items placed in that area.

• When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes

or you breathe it.

Firmware version ^{[Note 4]}

Notes

1: The mode of supported RGB signals

2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as

a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult

with a dealer about getting replacement for:

p.50

is shown.

TLPLW9 for TDP-T95 or

TLPLW10 for TDP-T100

(sold separately).

4: [Version] shows the version of the projector’s internal control program. This version is referred

to for customer service, etc.

Note

• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp replacement

A lamp is consumable supplies. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetime

Pull out the lamp.

Loosen the three lamp locking screws, pull up the

handle, and remove the lamp.

of the lamp depends on condition of use.) If this happens, replace it with a new one

WARNING

•

If the projector is mounted on the ceiling, it is recommended to use your Toshiba dealer-

ship when the lamp has to be exchanged.

Uncovering the lamp while the projector is mounted on a ceiling may lead to a danger

of damage from falling pieces of glass if the lamp is broken. Besides, working at high

elevations can also be hazardous. Do not attempt to replace the lamp by yourself.

• When replacement is required, be sure to use:

TLPLW9 for TDP-T95 or

TLPLW10 for TDP-T100

(sold separately).

Mount the new lamp.

Align the orientation, press down the new lamp

until the bottom is reached, and lock in place using

the three lamp locking screws.

CAUTION

•

If you have been using the projector, the lamp will be very hot, and may cause burn injuries

Wait for the lamp to cool (for longer than 1 hour) before replacing it.

If the lamp should break, please handle with care to avoid injury due to broken pieces and

contact your dealer for repair service.

Replace the lamp cover.

Align the cover, and press it in, then tighten the

screws loosened in step

no longer loose.

until the lamp cover is

Reset the lamp timer.

See the lamp’s manual for instructions on resetting

the lamp timer.

Unplug power cord.

Wait until lamp is sufficiently cooled.

Wait for at least 1 hour.

Notes and Precautions

• The Lamp time item in the Status display menu indicates the time of lamp use (as a

p.42

rough guide).

• It is recommended that the lamp be replaced after 2,000 hours of use. When [Lamp time]

reaches 2,000 hours, the icon and a message will appear. (After 2,000 hours, they will

appear when the power is on at the first time every 100 hours.) This display disappears

when you press the button.

Remove the lamp cover.

Lamp cover

Loosen the two screws, raise the lamp cover

with your fingers as shown to remove the lamp

cover. Use care to avoid any damage to nails

and/or tip of your finger(s). If you have any

difficulty in removal, you can use a screwdriver

or any other smaller tool for your convenience.

• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the

projector may fail to be powered on or the lamp may fail to come on.

• Always replace the lamp with a new one.

• The lamp is made out of glass. Do not touch the glass surface with your bare hands,

bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)

Used Lamps

This projector’s lamps contain trace amounts of environmentally harmful inorganic

mercury. Be careful not to break used lamps, and dispose of them in accordance with

local regulations.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lens and main unit cleaning

Trouble indications

The indicator lights to inform you of internal abnormalities.

WARNING

No power

⇒ Problem with projector

•

Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership

Attempting to clean/replace the lamp at a high site by yourself may cause you to fall

down, thus resulting in injury.

• Unplug the power cord, and contact your dealer.

(Off)

■ Lens cleaning

Lamp went out during use, or won’t come on

⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of the

lamp has ended or the projector is malfunctioning.

• Unplug the power cord and wait for a short while, then turn the power

back on.

• Clean the lens with a commercially available blower and/or

lens cleaner.

• The lens is easily scratched, so do not rub it with hard objects,

or strike it.

(Red lit)

• If a lamp burns out, replace it with a new one.

❈ After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

■ Main unit cleaning

• Clean the main unit after unplugging the power cord.

• Wipe dirt off the main unit gently with a soft cloth.

• Do not wipe the main unit with a damp cloth. Doing

so may allow water to get inside, resulting in an

electric shock or failure.

• Do not use benzene, thinner and the like as they may

deform or discolor the unit or damage the paint

surface.

Power went out during use

(Red lit)

Or (Orange lit)

⇒ Internal overheating, or the outside temperature is too high.

• Place the projector so that the air intake and exhaust are not blocked.

• Unplug the power cord and wait for a short while, then turn the power

back on.

(Green lit)

(Red lit)

❈ The

icon will appear before the power goes out.

❈ After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

• When using a chemically treated cloth, follow the

precautions included with the cloth.

Power went out during use

⇒ Problem with internal cooling fan.

• Unplug the power cord, and contact your dealer.

(Red lit or flashing)

❈ The

icon will appear before the power goes out.

Or (Orange lit

or flashing)

❈ After approx. one minute of abnormal display, the projector returns to

(Red lit)

the standby state waiting for internal cool down.

Power went out during use, or power won’t come on

⇒ The lamp cover is not properly attached.

p.44

• Unplug the power cord, and reattach the lamp cover.

(Orange

flashing)

❈ After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

(Red lit)

Power went out during use

⇒ Problem inside the projector.

• Unplug the power cord and wait for a short while, then turn the power

back on.

(Green

flashing)

• If the above action will not clear the problem, unplug the power cord,

and contact your dealer.

(Red lit)

❈ The

icon will appear before the power goes out.

❈ After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before calling service personnel

Specifications

If you think something is wrong, check the followings before contacting customer service.

■ List of general specifications

p.47

Please see “Trouble indications”

as well.

Item

Specification

Consumption Power

Weight

TDP-T95: 310 W

TDP-T100: 380 W

TDP-T95: 2.9 kg

TDP-T100: 3.0 kg

If This Happens

Check

• Is the power cord plugged in? Is it connected to the projector?

• Is the outer lamp cover attached properly?

No power

p.44

p.47

• Is the ambient temperature high?

• Is the air intake or air exhaust blocked?

Power goes out

during use

External Dimensions

(including protruding parts)

Cabinet material

300 × 99 × 218 mm (W × H × D)

p.47

p.40

PC+ABS resin and ABS resin

• Is the projector turned on? (When [Auto input search] is [Off])

No picture

p.30

Conditions for usage environment Temp: 5°C to 35°C; relative humidity: 30% to 70%

• Is the mute function on?

p.35

Display pixels

Picture elements

Lens

1 chip DMD™

• Is the brightness setting minimized?

• Are the connections set up correctly?

• Are all the connected devices functioning properly?

p.22

786,432 pixels (1024H × 768V)

Zoom lens

F=2.07-2.64 f=20.5-32.8 mm

Lamp

TDP-T95: High-pressure mercury lamp (210 W)

TDP-T100: High-pressure mercury lamp (275 W)

30-300 inches

1.07-11.09 m

1W (Mono)

p.30

• Is the mute function on?

No audio

p.27

• Is the volume setting minimized?

• Are the connections set up correctly?

• Are all the connected devices functioning properly?

Projection screen size

Projection distance

Speaker

p.22

p.50 p.51

• Is the input signal supported by the projector?

• Is there something generating an abnormal video signal, for

instance the video tape?

Picture not

displayed

correctly

COMPUTER 1

IN terminal

COMPUTER 2

Mini D sub 15 pin RGB / Y/PB/PR (dual use)

IN terminal

p.46

• Is the lens dirty?

Picture blurred

Part of picture

out of focus

p.27

MONITOR terminal

S-VIDEO terminal

AUDIO (L/R) terminal

VIDEO terminal

Mini D sub 15 pin RGB / Y/PB/PR (dual use)

Mini DIN 4 pin

• Is the lens focus adjusted optimally?

Is the projection distance within the projector’s supported range?

• Is the projector’s screen placement angle tilted too far?

• Are the sharpness or sampling phase adjustments off?

p.21

•

RCA Pin Jack × 2, 1.5 V (rms), 22 kΩ or more

RCA Pin Jack, 1 V (p-p), 75Ω

p.21

p.35

AUDIO (L/R) terminal

AUDIO IN terminal

AUDIO OUT terminal

CONTROL terminal

RCA Pin Jack × 2, 1.5 V (rms), 22 kΩ or more

p.35

• Are the brightness or contrast adjustments off?

• Is the lamp nearing the end of its service life?

Image is dark

3.5mm dia. stereo mini-jack, 1.5 V (rms), 22 k

3.5mm dia. stereo mini-jack

Mini DIN 8 pin (RS-232C)

Ω

or more

p.42

p.35

• Are the color, R-level, G-level, or B-level adjustments off?

• Is the screen dirty?

Colors too light

Bad shading

p.37

• Is the blackboard mode set properly?

Notes

p.42

• Is the lamp nearing the end of its service life?

• This model complies with the above specifications.

• Designs and specifications are subject to change without notice.

• This model may not be compatible with features and/or specifications that may be added

in the future.

p.41

• Is the key lock function on?

Control panel

key doesn’t work

p.19

• Is the remote control ON/OFF switch set off?

• Is the remote control code identical with the projector's code?

• Are the remote control’s batteries drained?

• Are the batteries inserted into the remote control correctly?

• Is the remote control being used within the effective range?

Are there any obstructions between the remote control and projector?

Remote control

doesn’t work

p.41

■ Separately sold product

p.19

Replacement Lamp for TDP-T95

Replacement Lamp for TDP-T100

Model TLPLW9

Model TLPLW10

p.19

•

• Are there any fluorescent or other bright lights shining at the

projector’s infrared remote sensor?

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (Continued)

■ List of supported signals (RGB signals)

■ List of supported signals (Y/PB/PR signals)

This projector supports the following RGB signals. Note, however, that depending on the

computer model, the screen may show flicker or streaking. Please adjust the projector if

this happens.

Signal format

fh(kHz)

15.73

31.47

15.63

31.25

45.00

37.50

33.75

28.13

fv(Hz)

59.94

50.00

60.00

50.00

60.00

50.00

480i(525i)@60Hz

480p(525p)@60Hz

576i(625i)@50Hz

576p(625p)@50Hz

720p(750p)@60Hz

720p(750p)@50Hz

1080i(1125i)@60Hz

1080i(1125i)@50Hz

Refresh rate

(Hz)

H-frequency

(kHz)

Clock

(MHz)

Resolution

Mode

720 x 400

640 x 480

720x400_85

VGA_60

VGA_72

VGA_75

VGA_85

SVGA_56

SVGA_60

SVGA_72

SVGA_75

SVGA_85

MAC16"

85.039

59.940

72.809

75.000

85.008

56.250

60.317

72.188

75.000

85.061

74.550

60.004

70.069

75.029

84.997

74.700

75.000

60.000

85.002

60.020

75.025

85.024

59.978

60.000

65.000

70.000

75.000

85.000

37.927

31.469

37.861

37.500

43.269

35.156

37.879

48.077

46.875

53.674

49.725

48.363

56.476

60.023

68.667

60.134

67.500

60.000

85.938

63.981

79.976

91.146

65.317

75.000

81.250

87.500

93.750

106.250

35.500

25.175

31.500

36.000

40.000

50.000

49.500

56.250

57.283

65.000

75.000

78.750

94.500

79.857

108.000

148.500

108.000

135.000

157.500

121.750

162.000

175.500

189.000

202.500

229.500

800 x 600

■ List of supported signals (Video, S-Video signals)

Video mode

NTSC

fh(kHz)

15.73

15.63

15.73

15.63

15.73

fv(Hz)

fsc(MHz)

3.58

PAL

4.43

832 x 624

1024 x 768

SECAM

PAL-M

4.25 or 4.41

3.58

XGA_60

XGA_70

XGA_75

XGA_85

PAL-N

3.58

PAL-60

NTSC4.43

4.43

MAC19"

4.43

1152 x 864

1280 x 960

SXGA1_75

QuadVGA_60

QuadVGA_85

SXGA3_60

SXGA3_75

SXGA3_85

SXGA+

UXGA_60

UXGA_65

UXGA_70

UXGA_75

UXGA_85

■ Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN &

1280 x 1024

MONITOR terminals

No.

Pin description

During Y/PB/PR input

During RGB input

Video signal (R)

Video signal (G)

Video signal (B)

GND

1400 x 1050

1600 x 1200

Color difference signal (PR

)

Luminance signal (Y)

Color difference signal (PB)

∗

GND

GND (R)

GND (PR)

Mini D sub 15 Pin connector

GND (G)

GND (Y)

Note

Input Signal

• RGB input

RGB signals:

Horizontal sync signal: TTL level (Pos/neg polarity)

Vertical sync signal: TTL level (Pos/neg polarity)

• Y/P^B/PR input

GND (B)

GND (PB)

• Signals whose resolution exceeds the native resolution (1024 × 768 pixels) will be

compressed. For this reason, some information may be lost, or image quality may be

affected.

N.C

∗

0.7V (p-p) 75 Ω

GND

N.C

Horizontal sync signal

Vertical sync signal

N.C

Y signal:

P^B/PR signals:

1.0V (p-p) 75 Ω

0.7V (p-p) 75 Ω

∗ Do not connect anything.

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications (Continued)

■ CONTROL terminal

● Pin assignment

Pin No.

Signal Name

RXD

Description

Receiving data

Consent to send

Data set ready

Signal ground

Request to send

No connection

Sending data

CTS

DSR

GND

RTS

N.C

TXD

GND

Signal ground

Mini DIN 8 pin connector

● Interface format

1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;

Stop Bit Length: 1 bit

2 Communication format

3 Data format

STX (02h) Command (3Byte) ETX (03h)

Only 1 command valid per communication.

For input commands, only ASCII-compliant all-uppercase

alphanumeric characters supported.

4 Replies

Acknowledge

ACK (06h) CR (0Dh) Data ... Normally ended

ACK (06h) ESC (1Bh)

NAK (15h)

... Aborted

No acknowledge

If commands are to be sent consecutively, wait for the response from the projector

before sending the next command.

● Main Commands

Item

Command

PON

Power on

Power off

POF

Icon display on

MO0

Icon display off

MO1

Auto setting (RGB input)

Status display on

Status display off

PAT

DON

DOF

Note

• Contact your dealer for control cable and other commands.

Download from Www.Somanuals.com. All Manuals Search And Download.

Technicolor Thomson DVD Player DTH700 User Manual
Toastmaster Juicer JM419SS User Manual
Toro Utility Vehicle 07367TC User Manual
Toshiba All in One Printer 120 150 User Manual
Toshiba Fax Machine TF831 861 User Manual
Toshiba Projection Television 72MX196 User Manual
Transition Networks TV Converter Box MGE PSW SX 01 User Manual
Ultra electronic All in One Printer M9006 644E User Manual
Victor Technology Calculator 1100 2 User Manual
ViewSonic Projector VS12680 User Manual