MX196_EN.book Page 1 Tuesday, June 27, 2006 1:43 PM
Integrated High Definition
®
DLP Projection Television
HIGH-DEFINITION TELEVISION
62MX196
72MX196
IMPORTANT NOTE
Before connecting, operating, or adjusting this product, carefully
read the Important Safety, Installation, Care, and Service
information in the separate Installation Guide.
For an overview of steps for setting up your new TV, see page 7.
I
Note: To display a High Definition picture, the TV must be receiving a
High Definition signal (such as an over-the-air High Definition TV
broadcast, a High Definition digital cable program, or a High Definition
digital satellite program). For details, please contact your TV antenna
installer, cable provider, or satellite provider.
Owner’s Record
The model number and serial number are on the back of
your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
Note: If the TV is powered off and then quickly on again when the
lamp unit is hot, it may take several minutes for the picture to appear
on-screen. This is a property of DLP® TV lamp technology and is NOT
a sign of malfunction. For details, see "IMPORTANT NOTICE ABOUT
HOT LAMP RESTART" on page 3.
Model number:
Serial number:
© 2006 TOSHIBA CORPORATION
All Rights Reserved
YC/N
VX1A00010200
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 3 Tuesday, June 27, 2006 1:43 PM
“Voice announce” feature
Trademark Information
When certain non-standard conditions occur, the LEDs
on the TV will blink and the TV will play a recorded
“voice announcement” describing the condition (see the
LED indication table on page 83 for the specific conditions
that include a voice announcement).
• This product incorporates copyright protection technology that is
protected by U.S. patents and other intellectual property rights. Use
of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
To repeat the voice announcement and hear additional
information, press the MENU button on the TV while the
LEDs are blinking.
• WOW, TruSurround, SRS and l symbol are trademarks of SRS
Labs, Inc.
WOW and TruSurround technologies are incorporated under
license from SRS Labs, Inc.
IMPORTANT NOTICE ABOUT HOT LAMP RESTART
When the TV has been powered on long enough for the lamp
unit to get hot, it may take several minutes for the picture to
appear in the following situations:
• Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are registered
trademarks of Dolby Laboratories.
• CableCARD™ is a trademark of Cable Television Laboratories, Inc.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
• When the Quick Restart™ feature is set to OFF and
you turn the TV off and then on again within a few
minutes; or
• If the TV is on when a short-term power failure, power
surge, or other similar power failure occurs, such that
the TV loses and regains power within a few minutes.
This is a property of DLP® technology and is NOT a sign
of malfunction.
If this occurs, the yellow LED on the TV front panel will blink
(and the blue LED will be lit solid) until the TV is finished
restarting the lamp and the normal picture appears. If both
LEDs are blinking, you will need to turn the TV off and then
on again to restart the lamp.
• Digital Light Processing®, DLP® and the DLP® medallion are
registered trademarks of Texas Instruments.
• In the United States, TV GUIDE and other related marks are
registered marks of Gemstar-TV Guide International, Inc. and/or one
of its affiliates. In Canada, TV GUIDE is a registered mark of
Transcontinental Inc., and is used under license by Gemstar-TV
Guide International, Inc. The TV Guide On Screen system is
manufactured under license from Gemstar-TV Guide International,
Inc. and/or one of its affiliates. The TV Guide On Screen system is
protected by one or more of the following United States patents
4,908,713; 6,498,895; 6,850,693; 6,396,546; 5,940,073; 6,239,794
to Gemstar-TV Guide International, Inc. and/or its subsidiaries.
• GEMSTAR-TV GUIDE INTERNATIONAL INC. AND/OR ITS
RELATED AFFILIATES ARE NOT IN ANY WAY LIABLE FOR THE
ACCURACY OR AVAILABILITY OF THE PROGRAM SCHEDULE
INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN
SYSTEM AND CANNOT GUARANTEE SERVICE AVAILABILITY IN
YOUR AREA. IN NO EVENT SHALL GEMSTAR-TV GUIDE
INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES BE
LIABLE FOR ANY DAMAGES IN CONNECTION WITH THE
ACCURACY OR AVAILABILITY OF THE PROGRAM SCHEDULE
INFORMATION OR OTHER DATA IN THE TV GUIDE ON SCREEN
SYSTEM.
3
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 4 Tuesday, June 27, 2006 1:43 PM
Contents
Selecting the POP window audio out. . . . . . . . . . . . . . . 41
POP double-window aspect ratio. . . . . . . . . . . . . . . . . . 41
Using the FREEZE feature . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Adjusting the picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Selecting the picture mode. . . . . . . . . . . . . . . . . . . . . . . 42
Adjusting the picture quality . . . . . . . . . . . . . . . . . . . . . 42
Using the closed caption mode . . . . . . . . . . . . . . . . . . . . . . . 43
Closed Caption Advanced . . . . . . . . . . . . . . . . . . . . . . . 43
Digital closed captions. . . . . . . . . . . . . . . . . . . . . . . . . . 44
Using the Closed Caption button on the
remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Adjusting the audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Muting the sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Using the digital audio selector . . . . . . . . . . . . . . . . . . . 44
Selecting stereo/SAP broadcasts . . . . . . . . . . . . . . . . . . 45
Adjusting the audio quality . . . . . . . . . . . . . . . . . . . . . . 45
Using the StableSound® feature. . . . . . . . . . . . . . . . . . . 46
Turning off the built-in speakers . . . . . . . . . . . . . . . . . . 46
Selecting the optical audio output format . . . . . . . . . . . 46
Using the Locks menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Entering the PIN code . . . . . . . . . . . . . . . . . . . . . . . . . . 47
If you cannot remember your PIN code. . . . . . . . . . . . . 47
Changing your PIN code . . . . . . . . . . . . . . . . . . . . . . . . 47
Blocking TV programs and movies
FCC Declaration of Conformity Compliance Statement
(Part 15): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important notes about your DLP® projection TV . . . . . . . . . . . 2
Trademark Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Welcome to Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Features of your new TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Overview of steps for installing, setting up, and
using your new TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TV front and side panel controls and connections . . . . . . . . . 8
TV back panel connections. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2: Using the remote control . . . . . . . . . . . . . . . . . . .11
Installing the remote control batteries . . . . . . . . . . . . . . . . . 11
Remote control effective range. . . . . . . . . . . . . . . . . . . . . . . 11
Learning about the remote control . . . . . . . . . . . . . . . . . . . . 12
Remote Control functional key chart . . . . . . . . . . . . . . . . . . 14
Using the remote control to operate your other devices . . . . 16
Programming the remote control to operate
your other devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Device code setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Searching and sampling the code of a device (8500). . . 17
Using the volume lock feature (8000) . . . . . . . . . . . . . . 17
Operational feature reset (8900). . . . . . . . . . . . . . . . . . . 17
Multi-brand remote control device codes . . . . . . . . . . . . . . . 18
by rating (V-Chip). . . . . . . . . . . . . . . . . . . . . . . . . . 48
Downloading an additional rating system
for blocking TV programs and movies . . . . . . . . . . 48
Blocking channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Unlocking programs temporarily. . . . . . . . . . . . . . . . . . 50
Using the input lock feature. . . . . . . . . . . . . . . . . . . . . . 50
Using the GameTimer™ . . . . . . . . . . . . . . . . . . . . . . . . . 51
Using the control panel lock feature . . . . . . . . . . . . . . . 51
Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Using the PC settings feature . . . . . . . . . . . . . . . . . . . . . . . . 53
Displaying TV status information using RECALL . . . . . . . 54
Understanding the auto power off feature . . . . . . . . . . . . . . 54
Understanding the last mode memory feature . . . . . . . . . . . 54
Chapter 3: Menu layout and navigation . . . . . . . . . . . . . . . . .22
Main menu layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Setup/Installation menu layout . . . . . . . . . . . . . . . . . . . . . . . 23
THINC™ menu layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Navigating the menu system. . . . . . . . . . . . . . . . . . . . . . . . . 24
Chapter 4: Setting up your TV. . . . . . . . . . . . . . . . . . . . . . . .25
Selecting the menu language . . . . . . . . . . . . . . . . . . . . . . . . 25
Configuring the antenna input sources for the
ANT 1 and ANT 2 terminals . . . . . . . . . . . . . . . . . . . . . 25
Programming channels into the TV’s channel memory . . . . 26
Programming channels automatically . . . . . . . . . . . . . . 26
Manually adding and deleting channels in the channel
Chapter 6: Using the TV’s advanced features . . . . . . . . . . . . .55
Using the advanced picture settings features . . . . . . . . . . . . 55
Using dynamic contrast . . . . . . . . . . . . . . . . . . . . . . . . . 55
Using CableClear® digital noise reduction . . . . . . . . . . 55
Using MPEG noise reduction. . . . . . . . . . . . . . . . . . . . . 56
Selecting the color temperature . . . . . . . . . . . . . . . . . . . 56
Selecting the lamp mode . . . . . . . . . . . . . . . . . . . . . . . . 57
Using the Vertical Edge Enhancer feature. . . . . . . . . . . 57
Using the Color Management feature . . . . . . . . . . . . . . 58
Using the Game Mode feature . . . . . . . . . . . . . . . . . . . . 58
Using the advanced audio settings features . . . . . . . . . . . . . 59
Using the SRS WOW™ surround sound feature . . . . . . 59
Using the virtual surround sound feature
memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Setting the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setting the ColorStream® HD audio mode . . . . . . . . . . . . . . 28
Setting the HDMI™ audio mode. . . . . . . . . . . . . . . . . . . . . . 29
Viewing the CableCARD™ menu. . . . . . . . . . . . . . . . . . . . . 29
Setting the Quick Restart™ feature . . . . . . . . . . . . . . . . . . . . 30
Viewing the digital signal meter. . . . . . . . . . . . . . . . . . . . . . 30
Viewing the system status. . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chapter 5: Using the TV’s features . . . . . . . . . . . . . . . . . . . .32
Selecting the video input source to view . . . . . . . . . . . . . . . 32
Labeling the video input sources . . . . . . . . . . . . . . . . . . . . . 32
Tuning channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Tuning channels using the Channel Browser™ . . . . . . . 33
Tuning to the next programmed channel . . . . . . . . . . . . 35
Tuning to a specific channel (programmed or
(Dolby® Virtual/SRS TruSurround™) . . . . . . . . . . . 59
unprogrammed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Switching between two channels
using Channel Return . . . . . . . . . . . . . . . . . . . . . . . 36
Switching between two channels using SurfLock™. . . . 36
Selecting the picture size . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Scrolling the TheaterWide® picture
(TheaterWide 2 and 3 only) . . . . . . . . . . . . . . . . . . . . . . 38
Using the auto aspect ratio feature . . . . . . . . . . . . . . . . . . . . 39
Selecting the cinema mode (480i signals only) . . . . . . . . . . 39
Using the POP features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Using the POP double-window feature . . . . . . . . . . . . . 40
4
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 5 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature . . . . . . . .60
A. Connecting the TV to your home network . . . . . . . . . . . 60
B. Setting up the network address . . . . . . . . . . . . . . . . . . . . 60
Automatically setting up the network address . . . . . . . . 60
Manually setting up the network address. . . . . . . . . . . . 61
Resetting the network address . . . . . . . . . . . . . . . . . . . . 62
C. Setting up file sharing on your PC . . . . . . . . . . . . . . . . . . 62
Compatible operating systems . . . . . . . . . . . . . . . . . . . . 62
Setting up file sharing on a PC with Microsoft®
Windows® XP Service Pack 1 or Service Pack 2 . . 62
Setting up file sharing on a PC with
Microsoft® Windows® 2000 . . . . . . . . . . . . . . . . . . 64
D. Setting up file sharing on the TV. . . . . . . . . . . . . . . . . . . 65
About the Software Upgrade feature . . . . . . . . . . . . . . . 65
E. Viewing/playing shared files on the TV. . . . . . . . . . . . . . 66
Media specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Using the Picture Viewer . . . . . . . . . . . . . . . . . . . . . . . . 67
Using the Audio Player . . . . . . . . . . . . . . . . . . . . . . . . . 69
F. Setting up e-mail scheduling . . . . . . . . . . . . . . . . . . . . . . 70
Required information and services. . . . . . . . . . . . . . . . . 70
Setting up e-mail scheduling . . . . . . . . . . . . . . . . . . . . . 70
Setting up SMTP authentication . . . . . . . . . . . . . . . . . . 72
Description of fields in the “E-mail Scheduling Setup”
window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
G. Using e-mail scheduling . . . . . . . . . . . . . . . . . . . . . . . . . 76
E-mail parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Sending a request e-mail to the TV . . . . . . . . . . . . . . . . 76
Formatting a request e-mail . . . . . . . . . . . . . . . . . . . . . . 76
Sample request e-mails . . . . . . . . . . . . . . . . . . . . . . . . . 77
Receiving an e-mail from the TV. . . . . . . . . . . . . . . . . . 78
Modifying an existing recording or reminder . . . . . . . . 78
Chapter 8: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .79
General troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Home network troubleshooting . . . . . . . . . . . . . . . . . . . . . . 81
LED indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Chapter 9: Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Lamp unit replacement and care. . . . . . . . . . . . . . . . . . . . . . 84
Replacing the lamp unit
(User-replaceable component). . . . . . . . . . . . . . . . . 84
When to replace the lamp unit . . . . . . . . . . . . . . . . . . . . 84
How to replace the lamp unit . . . . . . . . . . . . . . . . . . . . . 85
Disposing of the used lamp unit. . . . . . . . . . . . . . . . . . . 86
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Limited United States Warranty
for DLP® Television Models . . . . . . . . . . . . . . . . . . . . . 88
Limited Canada Warranty
for DLP® Television Models . . . . . . . . . . . . . . . . . . . . . 89
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
5
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 6 Tuesday, June 27, 2006 1:43 PM
Chapter 1: Introduction
NOTICE OF POSSIBLE TV STAND INSTABILITY
Features of your new TV
DANGER: RISK OF SERIOUS PERSONAL
INJURY OR DEATH! Use this TV only with
the TOSHIBA TV stand listed in the
The following are just a few of the many exciting features of
your new Toshiba widescreen, integrated HD, DLP®
projection TV:
• Integrated digital tuning (8VSB ATSC and QAM)
eliminates the need for a separate digital converter set-top
box (in most cases).
“Specifications” section of this manual. Use with other
stands may result in instability, causing possible injury or
death.
• TV Guide On Screen™ no-fee interactive program guide
(- TV Guide On Screen™ Interactive Program Guide).
Welcome to Toshiba
• Digital CableCARD™ slot for viewing encrypted digital
Thank you for purchasing this Toshiba TV, one of the most
innovative DLP® projection TVs on the market.
Cable TV programs (- Installation Guide).
• Two HDMI™ digital, high-definition multimedia interfaces
This digital television is capable of receiving analog basic,
digital basic, and digital premium cable television
programming by direct connection to a cable system providing
such programming. A security card provided by your cable
operator is required to view encrypted digital programming.
Certain advanced and interactive digital cable services (such as
video-on-demand, a cable operator's enhanced program guide,
or data-enhanced television services) may require the use of a
set-top box. For more information, call your local cable
operator.
We have provided three separate Guides to facilitate the
installation and operation of your TV.
Please use the Guides in the order shown below to get the
most enjoyment from your new TV.
1) The Installation Guide explains how to connect your TV
to your antenna and equipment.
2) The Operating Guide (this Guide) provides step-by-step
instructions for using your TV's many features.
3) The TV Guide On Screen™ Interactive Program Guide
explains how to set up and navigate the TV Guide
On Screen™ system in your TV.
(- Installation Guide).
• Two sets of ColorStream® HD high-resolution component
video inputs (- Installation Guide).
• Dolby Digital (- Installation Guide), SRS WOW™, and
Dolby Virtual/SRS TruSurround™ (- page 59) audio
technologies.
• Digital Audio Out optical audio connection with Dolby®
Digital optical output format (- page 46; also see
Installation Guide).
• CableClear® digital picture noise reduction
(- page 55).
• Double-window POP feature (- page 40).
• PC IN (Analog RGB) for using the TV screen as the display
for a PC (- Installation Guide).
• Ethernet (RJ-45) (THINC™) port for connecting the TV
to a home network to enable file sharing (JPEG, MP3) and
e-mail scheduling of recordings and reminders
(- Chapter 7 and Installation Guide).
Note: The TV screen graphics in the Guides are for illustration
purposes only and may be different from the screens
displayed on your TV.
6
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 7 Tuesday, June 27, 2006 1:43 PM
Chapter 1: Introduction
11 After you plug in the TV power cord, the yellow LED
(on the TV front) will blink 3 times. Wait several seconds
until the yellow LED stops blinking and then press p on
the TV or remote control.
Overview of steps for installing,
setting up, and using your new TV
See “LED indications” (- page 83).
Follow these steps to set up your TV and begin using its many
exciting features.
12 See “Menu layout and navigation” for a quick overview of
the TV’s menu system (- page 22).
1
2
Carefully read the important safety, installation, care, and
service information in the separate Installation Guide.
Keep this manual for future reference.
13 See the separate TV Guide On Screen™ Interactive
Program Guide for details on setting up and using the
TV Guide On Screen™ system (if available in your area).
Observe the following when choosing a location for the
TV:
• Read the separate Installation Guide.
• Read the separate TV Guide On Screen™ Interactive
Program Guide.
• Read “Important notes about your DLP® projection
TV” (- page 2).
• Place the TV on the applicable optional TV stand listed
in the “Specifications” section (if available for this TV
model) or on a sturdy, level, stable surface that can
safely support the size and weight of the unit.
• Place the TV in a location where light does not reflect
on the screen.
14 Program channels into the TV’s channel memory
(- page 26).
15 For details on using the TV’s features, see Chapters 5
and 6.
16 For details on connecting the TV to a home network to
enable file sharing and e-mail scheduling of recordings,
see Chapter 7.
17 For help, refer to the Troubleshooting Guide, Chapter 8.
18 For lamp unit replacement instructions, see Chapter 9.
19 For technical specifications and warranty information, see
Chapter 9.
20 Enjoy your new TV!
• Place the TV far enough from walls and other objects to
allow proper ventilation. Inadequate ventilation may
cause overheating, which will damage the TV. THIS
TYPE OF DAMAGE IS NOT COVERED UNDER
THE TOSHIBA WARRANTY.
3
4
Do not plug in any power cords until AFTER you have
connected all cables and devices to your TV.
BEFORE connecting cables or devices to the TV, learn
the functions of the TV’s connections and controls
(- pages 8–10).
5
6
Connect your other electronic device(s) to the TV
(- Installation Guide).
Connect the supplied G-LINK™/IR blaster cable from
your VCR and/or Cable box (if applicable) to the
G-LINK™ terminal so you can use the TV Guide
On Screen™ features (applies to VCRs and cable boxes
only) (- Installation Guide).
7
8
Install the batteries in the remote control (- page 11).
See “Learning about the remote control” (-page 12) for
an overview of the buttons on the remote control.
9
Program the remote control to operate your other
device(s) (- pages 16–21).
10 AFTER connecting all cables and devices, plug in the
power cords for your TV and other devices.
7
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 8 Tuesday, June 27, 2006 1:43 PM
Chapter 1: Introduction
TV front and side panel controls and connections
TV front
Side panel
1
2
LAMP
11
3
4
7*
8
POWER
TIMER
REC
5
6
9
10
Control panel
1
2
Remote sensor (behind the screen) — Point the remote
control toward this area of the TV screen (- “Remote
control effective range” on page 11).
7
*MENU (ENTER) — Press to access the menu system
(- pages 22–23). When a menu is on-screen, the MENU
button on the TV’s side control panel functions as the
ENTER button.
Blue, Yellow and Green/Red LEDs
See “LED indications” on page 83 for additional
information.
8
9
ARROWS BbC c — When a menu is on-screen, these
buttons function as up/down/left/right menu navigation
buttons.
3
POWER — Press to turn the TV on and off.
EXIT — Press to instantly close an on-screen menu.
If the TV stops responding to the controls on the remote
control or TV control panel and you cannot turn off the
TV, press and hold the POWER button on the TV control
panel for 5 or more seconds to reset the TV.
10 GUIDE — Press to access the TV Guide On Screen™
program guide (- TV Guide On Screen™ Interactive
Program Guide).
4
5
6
CHANNEL U u — When no menu is on-screen, these
buttons change the channel (programmed channels only;
- page 26). When a menu is on-screen, these buttons
function as up/down menu navigation buttons.
11 VIDEO-2 IN — The side panel A/V connections are
referred to as “VIDEO 2” and include standard A/V
inputs plus an optional S-video input.
VOLUME + – — When no menu is on-screen, these
buttons adjust the volume level. When a menu is
on-screen, these buttons function as left/right menu
navigation buttons.
INPUT — Repeatedly press to change the source
you are viewing (ANT 1, VIDEO 1, VIDEO 2,
ColorStream HD-1, ColorStream HD-2, HDMI 1,
HDMI 2, PC, ANT 2).
8
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 9 Tuesday, June 27, 2006 1:43 PM
Chapter 1: Introduction
TV back panel connections
For an explanation of cable types and connections, see the Installation Guide.
1
2
3
4
5
6
7
1
2
VIDEO 1 IN — Composite video and analog audio inputs
plus optional S-video inputs for connecting devices with
composite video or S-video output.
4
A/V OUT — Standard composite video and analog audio
outputs for connecting a VCR for editing and dubbing.
When the POP double-window is open, the active window
sound is output (- page 41).
Note: Composite video and S-video cables carry only
video information; separate audio cables are required for
a complete connection.
Note: The A/V OUT terminals will output AUDIO ONLY (no
video) in the following instances:
• When the TV's INPUT mode is HDMI, ColorStream or
PC (- “Selecting the video input source to view,”
page 32).
ColorStream® HD-1 IN and ColorStream® HD-2 IN
— Two sets of ColorStream® high-definition component
video inputs (with analog stereo audio inputs) for
connecting devices with component video output, such as
a Toshiba DVD player with ColorStream®.
• When the MP3 Audio Player is active (- page 69).
5
6
PC IN — For connecting audio and video from a personal
computer to use the TV screen as the display for the PC
(- Installation Guide).
Note:
• Component video cables carry only video information;
separate audio cables are required for a complete
connection.
• HDMI 1 (and 2) share analog audio inputs with
ColorStream HD-1 (and HD-2). To specify the use of the
audio inputs for a connected ColorStream (component
video) device, see “Setting the ColorStream HD audio
mode” on page 28.
IR OUT — For controlling infrared remote-controlled
devices through the TV. You can connect up to two
devices with an IR blaster cable, and then control the
devices using the TV’s IR pass-through features.
7
ANT 1 and ANT 2 — Two inputs that support analog
(NTSC) and digital (ATSC) off-air antenna signals and
analog and digital Cable TV (QAM) signals.
3
Variable Audio OUT — Standard analog audio outputs
for connecting an analog amplifier with external speakers.
When the POP double-window is open, the active window
sound is output (- page 41).
Note: If you have an antenna only, connect it to ANT 1. If
you have both cable TV and an antenna, connect the
cable TV to ANT 1 and the antenna to ANT 2.
(continued)
9
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 10 Tuesday, June 27, 2006 1:43 PM
Chapter 1: Introduction
8
9 10 11
12
8
HDMI™ 1 IN and HDMI™ 2 IN — Two High-Definition
11 RJ-45 (Ethernet) (THINC™ system**) — For
connecting the TV to your home network. See boxed note
below.
Multimedia Interface inputs receive digital audio and
uncompressed digital video from an HDMI device or
uncompressed digital video from a DVI device.
Also see item 2.
**THINC™ system
(Toshiba Home Interactive Network Connection)
The RJ-45 (Ethernet) port allows your Toshiba TV to
connect to your home network. You can use this
revolutionary home entertainment networking system to
access MP3 audio files and JPEG picture files that are
stored as shared files on a networked PC and play/display
them on your TV.
Note: HDMI 1 (and 2) IN share analog audio inputs with
ColorStream HD-1 (and HD-2) IN. To specify the use of the
audio inputs for a connected HDMI (or DVI) device, see
“Setting the HDMI audio mode” on page 29.
9
G-LINK™ — For use with the enclosed IR blaster/
G-LINK™ cable to enable the TV Guide On Screen™
recording features (- Installation Guide).
You also can play your shared MP3 audio files through a
connected audio system.
See Chapter 7 for details. Also see the Installation Guide.
10 Digital Audio OUT — Optical audio output in Dolby*
Digital or PCM (pulse-code modulation) format for
connecting an external Dolby Digital decoder, amplifier,
A/V receiver, or home theater system with optical audio
input.
12 CableCARD™ slot — For use with a digital security
card and digital cable TV service (provided by your local
cable operator) to view encrypted digital programming
(- page 29).
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC.
CableCARD is a trademark of Cable Television Laboratories, Inc.
* Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are registered
trademarks of Dolby Laboratories.
10
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 11 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
Installing the remote control
batteries
Remote control effective range
For optimum performance, aim the remote control directly at
the TV remote sensor. Make sure there are no obstructions
between the remote control and the TV.
To install the remote control batteries:
1
Slide the battery cover off the back of the remote control.
Point remote control
toward remote sensor
on front of TV.
2
Install two “AA” size alkaline batteries. Match the + and
– symbols on the batteries to the symbols on the battery
compartment.
16.4 ft (5m)
3
Slide the battery cover on to the remote control until the
lock snaps.
Caution: Never throw batteries into a fire.
Note:
• Be sure to use AA size alkaline batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the
environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with
new ones.
• When necessary to replace batteries in the remote control,
always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
• Always remove the batteries from the remote control if they
are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from
leaking into the battery compartment.
11
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 12 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
1
LIGHT illuminates the keypad for five seconds.
The MODE SELECT key that is being selected blinks
three times.
Learning about the remote control
The buttons used for operating the TV only are described here.
For a complete list of the remote control’s functions, see the
remote control functional key chart (- pages 14–15).
For a list of the buttons that operate the TV Guide On Screen™
system, see the separate TV Guide On Screen™ Interactive
Program Guide.
2
3
SLEEP accesses the sleep timer (- page 52).
POWER turns the TV on and off. When the TV is on, the
blue LED indicator on the TV front will be illuminated.
Note: The Quick Restart™ setting will affect the amount of
time it takes for the picture to appear when you turn on the
TV (- page 30).
4
MODE SELECT sets the six remote control device
modes: TV, CABLE/SAT, DVD, VCR/PVR, AUX 1,
and AUX 2. Press TV until the keypad blinks 3 times to
control the TV.
The selected MODE key blinks each time any key is
pressed. (- page 16).
5
Channel Numbers (0–9, –/100) directly tune
channels. The = button is used to tune digital channels
(- page 35) or to edit the Favorite List (- page 33).
6
7
INPUT selects the video input source (- page 32).
FAV BROWSER accesses the Favorites List in the
Channel Browser™ (- page 33).
8
MENU accesses the main TV menu system (- pages 22
and 23) or opens a menu in the TV Guide On Screen™
system (- TV Guide On Screen™ Interactive Program
Guide).
9
ENTER activates highlighted items in the main menu
system and the TV Guide On Screen™ system.
10 THINC accesses the THINC menu (- page 24).
11 PAGE + - When the TV Guide On Screen™ system is
open, moves from one set of screen information to the
next, when applicable.
12 TV GUIDE opens the TV Guide On Screen™ system
(- TV Guide On Screen™ Interactive Program Guide).
13 3 C / # c While watching TV, these buttons open the
Channel Browser™ and tune to the previous/next channel
in the History List (- page 34). (Also see “Arrow
buttons,” below.)
14 Arrow buttons (BbC c) When a menu is on-screen,
these buttons select or adjust programming menus. (Also
see 3 C / # c.)
15 VOL + - adjusts the volume level.
16 CH Bb cycles through programmed channels when no
menu is on-screen (- page 26), and functions as page up/
down when a menu is on-screen or when the TV Guide
On Screen™ system is open (- TV Guide On Screen™
Interactive Program Guide).
Note: The error message “Not Available” may appear if you
press a key for a function that is not available.
12
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 13 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
17 EXIT closes on-screen menus and the TV Guide
On Screen™ system.
18 INFO provides detailed information on highlighted items
in the TV Guide On Screen™ system (- TV Guide
On Screen™ Interactive Program Guide).
19 MUTE reduces or turns off the sound (- page 44).
20 CH RTN returns to the last viewed channel (- page 36),
or stops the picture viewer slide show (- page 68). Also
can be used to switch between the song select view and
file select view in the Audio Player (- page 69).
21 RECALL displays TV status information (- page 54).
22 SKIP Z and SKIP z jump backward and forward one
day at a time in the TV Guide On Screen™ listings (-TV
Guide On Screen™ Interactive Program Guide).
23 C.CAPTION (TV/VCR) opens the closed caption/audio
selector screen. (The audio selector is not available for
analog channels.) (- pages 43–44.) Also can be used to
select the TV mode to view one program while recording
another.
24 POP opens the POP double-window (- page 40) or
locks/unlocks the TV Guide On Screen™ video window
(- TV Guide On Screen™ Interactive Program Guide).
25 FREEZE freezes the picture. Press again to restore the
moving picture.
26 PIC SIZE cycles through the pictures sizes: Natural,
TheaterWide 1/2/3, and Full (- page 37).
13
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 14 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
Remote Control functional key chart
•
DVD/VCR
combo
REMOTE
Toshiba TV
SAT
(satellite)
Receiver/
AMP
CD
(AUDIO)
CABLE
VCR
PVR
CONTROL KEY (TV)
• DVD/
DVD-R
MODE
Remote control device mode selection
Lights the remote key.*1
SELECT
LIGHT
SLEEP
Sleep timer
Power
s TV
Power
Digit 1
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
Digit 7
Digit 8
Digit 9
Digit 0
s TV
Power
Digit 1
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
Digit 7
Digit 8
Digit 9
Digit 0
s TV
Power
Digit 1
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
Digit 7
Digit 8
Digit 9
Digit 0
s TV
Power
Digit 1
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
Digit 7
Digit 8
Digit 9
Digit 0
s TV
Power
s TV
Power
s TV
Power
Digit 1
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
Digit 7
Digit 8
Digit 9
Digit 0
POWER
1
2
3
4
5
6
7
8
9
0
Digit 1
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
Digit 7
Digit 8
Digit 9
Digit 0
AV input 1
AV input 2
AV input 3
AV input 4
CD
Digit 1
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
Digit 7
Digit 8
Digit 9
Digit 0, 10
Tuner
Phono
Cassette
Aux
---
–/--,
+10,
+100
–/--,
+10,
+100
– (digital
separator)
100/–/+10
---
+100
---
---
---
TV/Video
select
INPUT
s TV
s TV
Menu
s TV
s TV
Menu
s TV
s TV
---
s TV
s TV
Menu
Input
s TV
s TV
Menu
s TV
s TV
Menu
Selects the
image shape
PIC SIZE
MENU
s TV
Menu
Menu/Guide
Menu
FAV
BROWSER/
SET UP
FAV
BROWSER
---
---
---
Setup
---
---
---
THINC/
TOP MENU
THINC
s TV
s TV
s TV
Top menu
s TV
s TV
s TV
TV GUIDE
INFO
TV Guide
Guide Info
Enter
Guide
Info
Guide
Info
---
---
---
Guide
Display
Select
---
---
---
---
---
---
Guide
Info
ENTER
Select
Select
Select
Menu select
up
B
b
Cursor up
Cursor up
---
---
Cursor up
---
---
---
---
Cursor up
Menu select
down
Cursor
down
Cursor
down
Cursor
down
Cursor
down
Menu select
left/right
Cursor left/
right
Cursor left/
right
Cursor left/
right
Cursor
left/right
C 3 # c
---
---
---
3 Back
# Next
EXIT/
Exit
Exit
Exit
---
---
DVD clear
---
---
---
---
Exit
---
DVD CLEAR
Page up/
down
Page up/
down
Page up/
down
Page up/
down
PAGE +/–
VOL +/–
Volume up/
down*2
Volume up/
down*2
Volume up/
down*2
Volume up/ Volume up/ Volume up/ Volume
down*2 down*2 down*2 up/down*2
Volume
up/down*2
14
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 15 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
•
DVD/VCR
combo
REMOTE
Toshiba TV
SAT
(satellite)
Receiver/
AMP
CD
(AUDIO)
CABLE
VCR
PVR
CONTROL KEY (TV)
• DVD/
DVD-R
CH RTN/
DVD RTN
Previous
channel
Previous
channel
Previous
channel
---
DVD RTN
---
---
---
On-screen
display
RECALL
MUTE
s TV
s TV
s TV
s TV
s TV
s TV
s TV
Sound
mute*2
Sound
mute*2
Sound
mute*2
Sound
mute*2
Sound
mute*2
Sound
mute*2
Sound
mute*2
Sound mute
Slow FWD*
Slow REW*
Slow FWD
Slow REW
Slow FWD
Slow REW
SlowFWD
Slow REW
SLOW
---
---
---
---
---
---
---
SKIP z
SKIP Z
DAY+
DAY–
Skip FWD
Skip REW
Skip FWD
Skip REW
---
---
REW
Rewind*
Pause*
Rewind
Pause
Rewind
Pause
Rewind
Pause
Rewind
Pause
---
---
---
---
Rewind
Pause
Rewind
Pause
PAUSE/STEP
PLAY
Play*
Play
Play
Play
Play
Play
Play
FF
Fast FWD*
Fast FWD
Fast FWD
Fast FWD
Fast FWD
Fast FWD
Fast FWD
C.CAPTION
TV/VCR
C.Caption
---
TV/SAT
TV/VCR
---*4
---
---
---
Disc SKIP
Disc select
Instant
replay
DISC/AM/FM
STOP
---
---
---
---
---*5
Stop
AM/FM
---
Stop*
Stop
Stop
Stop
Stop
Stop
REC Menu
(Single
click)
Record
(Double
click)
Record
(Double
click)
Record
(Double
click)
Record
(Double
click)*3
Record
(Double
click)
REC
---
---
Channel up/
down
Channel up/
down
Channel up/
down
Channel
up/down
Channel
up/down
Channel
up/down
Channel
up/down
CH B b
---
POP
Split
s TV
s TV
s TV
s TV
s TV
s TV
s TV
FREEZE
Freeze
s TV
s TV
s TV
s TV
s TV
s TV
s TV
Note:
• “---” = key does not send a signal in that remote control mode.
• “s TV” = key will affect the TV, even though the remote control is in another mode.
• * Not available for your TV.
*1
Does not send IR signal.
*2
Volume will affect the TV by default. When the volume is unlocked, all the devices will have their own volume if their ID has volume data. The
AUDIO modes (receiver, CD) will have their own volume if volume lock is set on TV, CABLE/SAT, VCR/PVR, or DVD mode. See “Using the
volume lock feature” (- page 17).
DVD/DVD-R : RECORD is only for DVD-R, no function is picked for DVD.
DVD/VCR combo : TV/VCR
DVD/VCR combo : DVD/VCR
*3
*4
*5
15
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 16 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
Using the remote control to operate Programming the remote control to
your other devices
operate your other devices
Your TV remote control has one dedicated TV mode and five
programmable multi-brand modes: CABLE/SAT, DVD,
VCR/PVR, AUX 1, and AUX 2. The default device modes
and programmable device modes are listed below.
Device code setup
1
Find the code for your device brand in the remote control
device code table on pages 18–21.
Note: The TV remote control is preprogrammed to operate
most Toshiba devices. To operate a non-Toshiba device or a
Toshiba device that the remote control is not preprogrammed
to operate, you will need to program the remote control. See
“Programming the remote control to operate your other
devices” (at right).
If more than one code is listed, try each one separately
until you find one that works.
2
3
Press the applicable MODE SELECT button (CABLE/
SAT, DVD, VCR/PVR, AUX 1, or AUX 2), until the
MODE SELECT button blinks 3 times.
Default device mode control (before
While holding down E, press the Number buttons to
enter the category code (0, 1, 2, 3, 4, or 5, as described
below) plus the four-digit device code for your device.
MODE SELECT
programming)
TV
Toshiba TV
CABLE/SAT Toshiba DST 3100 Satellite receiver
Category
Category code
DVD
Orion DVD
TVs (Toshiba)
0
VCR/PVR
AUX 1
AUX 2
Toshiba VCR
Cable boxes
Satellite receivers
Cable/PVR combos
DBS/PVR combos (1)
Yamaha Audio receiver
Onkyo Audio receiver
1
DVD players
2
3
MODE SELECT Device mode control after programming
VCRs
PVRs
TV
Toshiba TV
DBS/PVR combos (2)
CABLE/SAT
DVD
Audio Amps
Audio Amps/Tuners
4
5
VCR/PVR
AUX 1
AUX 2
Multi-brand video/audio devices
CD players
• If a valid code is entered, the MODE SELECT button
will blink twice.
Note: Although your new TV’s remote control includes codes
for many devices, it may not include codes for some or all of
the features on certain devices you wish to control. If you are
unable to program the TV’s remote control to operate your
device or some of the features on that device, use the device’s
original remote control (or the control buttons on the device).
• If an invalid code is entered, the MODE SELECT
button will blink one long blink.
4
Point the remote control at the device and press p to test
the code.
• If the device responds to the remote control, you have
entered the correct code.
• If the device does not respond to the remote control,
repeat steps 3 and 4 using another code.
Note: After programming the remote control, make sure
all necessary keys on the TV remote control (in addition to
p) operate your device. If some keys are not
operational, repeat the device code setup using another
code (if other codes are listed for your device). If, after
trying all listed codes, the necessary keys do not operate
your device, use the device’s original remote control.
16
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 17 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
5
Note:
To control the TV, press the TV MODE SELECT button.
Using the volume lock feature (8000)
By default (factory setting), the remote control’s volume keys
• Although the TV remote control includes codes for many
devices, it may not include codes for some or all of the
features on certain devices you want to control. If you are
unable to program the TV remote control to operate your
device or some of the features on that device, use the
device’s original remote control (or the control buttons on
the device).
• Every time you change the batteries you will need to
reprogram the remote control.
• Some newer VCRs respond to either of two codes. These
VCRs have a switch labeled “VCR1/VCR2.” If your VCR has
this kind of switch and does not respond to the codes for
your VCR brand, set the switch to the other position (“VCR1”
or “VCR2”) and reprogram the remote control.
(z Z and W) are locked to the “TV” device mode.
The remote control will operate the TV’s volume, even when
“TV” is not the current device mode. (This includes all remote
control device modes except AUX 1 and AUX 2).
If you unlock the remote control’s volume keys, each device
mode will have its own volume (if the device ID has volume
data). The remote control will operate the volume of the device
associated with the current device mode. (This includes all
remote control device modes.)
If you lock the remote control’s volume keys to a specific
device mode, the remote control will operate the volume of the
device associated with the locked mode, even when the locked
mode is not the current device mode. (This includes all device
modes except AUX 1 and AUX 2).
When the remote control is in AUX1 (or AUX 2) mode, the
remote control will operate the volume of the device associated
with the AUX 1 (or AUX 2) mode, even when the volume is
locked to another mode.
See “Using the remote control to operate your other devices”
on page 16.
Searching and sampling the code of a
device (8500)
If you do not know the device code for a particular device, you
can cycle the remote control through the available codes for
that device mode and sample the functions to find the code that
operates the target device. The keys available to be sampled,
provided they are applicable to that mode, are p, 1, z, <,
and S. Invalid keys will be ignored while in program mode.
To lock the remote control’s volume keys to a specific
mode (CABLE/SAT in this example):
To cycle through each available device code and
sample its functions:
1
2
3
Press CABLE/SAT.
While holding down the E button, press 8, 0, 0, 0.
Press z. The CABLE/SAT MODE SELECT button will
1
2
3
Press the appropriate MODE SELECT button on the
remote control.
blink two times (locked).
The remote control’s volume keys will now operate the
volume of the device associated with the CABLE/SAT
mode, even when CABLE/SAT is not the current device
mode (for all device modes except AUX 1 and AUX 2).
While holding down E, press 8, 5, 0, 0. The remote
control will enter program mode.
Point the remote control at the target device and press p
(or other function buttons that are available to be
sampled).
To unlock the remote control’s volume keys:
4
If the device responds to the remote control:
1
2
While holding down E, press 8, 0, 0, 0.
Press E to store the device code. The MODE
SELECT button will blink two times and the remote
control will exit the program mode.
Press Z. The CABLE/SAT MODE SELECT button will
blink four times (unlocked).
If the device does not respond to the remote control:
Press B, and then press p. Repeat this step until the
device responds to the remote control, and then press
E.
Note: When a search cycle is completed, the mode select
button will blink three times. The remote control will begin
to cycle through the available codes again. If no key is
pressed within 10 seconds during programming, the
remote control will exit the program mode and return to the
previous code.
Operational feature reset (8900)
This feature clears all programmed remote control features not
related to “Device code setup” and resets the volume lock to
the “TV” device mode.
To reset the remote control:
While holding down E, press 8, 9, 0, 0. The MODE
SELECT button will blink four times.
17
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 18 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
DirecTV
0099, 0247, 0392,
0566, 0639, 0724,
0749, 0819,
1076, 1108, 1109,
1142, 1377, 1392,
1414, 1442,
1443, 1444, 1609,
1639, 1640, 1749,
1856
0775, 1005, 1170,
1505, 1775
0775, 1005, 1505,
1775
DVD players
Multi-brand remote
control device codes
Brand
Aiwa
Akai
Alco
Allegro
Amphion Media
Works
AMW
Apex Digital
Code
0641
0695, 0770, 1089
0790
0869
TVs
0872
0872
Brand
Toshiba
Code
1524
Dish Network System
Dishpro
0672, 0717, 0755,
0794, 0796, 0797,
1004, 1020,
1056, 1061, 1100
1168, 1407
0790, 1041, 1072
1072
0655, 0662
0717
0571
0695
0490
0831
0833, 0869, 0876
1277
Cable boxes
Echostar
0775, 1005, 1170,
1505, 1775
0775, 1775
0392, 0566
0775, 1775
1246
1535
0819, 1250
0775, 1775
Brand
ABC
Code
0003, 0008
0899
0899
0883
0883
0883
1187
0476
Aspire Digital
Audiovox
Axion
Expressvu
GE
GOI
Goodmans
Hisense
Hitachi
Americast
Bell South
Clearmaster
ClearMax
Coolmax
Digeo
Director
GoldStar
Hamlin
Memorex
Motorola/
General Instrument/
Jerrold
Motorola
General Instrument/
Jerrold
Multitech
Pace
Panasonic
Paragon
B & K
Blaupunkt
Blue Parade
Broksonic
California Audio Labs
Cinea
CineVision
Citizen
Coby
HTS
Hughes
Hughes Network
Systems
0749, 1442, 1749
0144
0009, 0273
0000
0749, 1142, 1442,
1443, 1444, 1749
1535
0778, 0852, 1086,
1107, 1177, 1351
0831
iLo
Janeil
JVC
LG
0152
Craig
Curtis Mathes
CyberHome
0276, 0476, 0810
1187, 1376
0775, 1170, 1775
1226, 1414
0722, 0724
0724
1087
0816, 0874, 1023,
1024, 1117, 1129
0705, 0784, 0833,
0869, 1169, 1172,
1234, 1242
0872
0490, 0634
1407
0675, 1270
1068, 1085
1127
Magnavox
Memorex
Mitsubishi
Motorola/General
Instrument/Jerrold
Motorola
NEC
Next Level
Panasonic
Paysat
0003
0883
Daewoo
0749
0008, 0237, 1877
0000, 0107
0000
0317, 1305
0144, 0533, 0877,
1877
0000
0000
0883
0273, 0279
0000
0144
0008, 0477, 0877,
1877
1006
0003
0276
0883
0003
0000
0869
0856
0102, 0178, 1270
0869
0152, 0247, 0701
0724
0099, 0722, 0724,
0749, 0819, 1076,
1142, 1442,
1749
1442
0392, 0566
1535
Daytek
Denon
Desay
Disney
Dual
Durabrand
DVD2000
Emerson
Enterprise
Fisher
Funai
Gateway
GE
Philips
Pioneer
Pulsar
Quasar
RadioShack
Regal
Runco
Philips
0521
0591, 0675, 0821
0591
0670
Samsung
Scientific Atlanta
Pioneer
Proscan
Proton
RadioShack
RCA
0675, 1334
1073, 1077, 1158
0522, 0717, 0815
0715, 0741, 0744,
0783, 0833, 0869,
1044, 1075,
1099, 1158, 1304,
1730
1072
0741
0699, 0769
0490
0717
Sony
0869
Go Video
Starcom
Supercable
Supermax
Torx
Toshiba
Tristar
V2
Viewmaster
Vision
0143, 0392, 0566,
0855, 1392
1108, 1109, 1142,
1276, 1377, 1442,
1609
1219
0639, 1639, 1640
0869
Samsung
GoVision
GoldStar
GPX
Gradiente
Greenhill
Grundig
Harman/Kardon
Hitachi
Hiteker
iLo
Sanyo
Sony
Star Choice
Tivo
0883
0883
0883
0883
0883
0000, 0525, 0899
1142, 1442, 1443,
1444
Vortex View
Zenith
0539
Toshiba
0082, 0749, 0790,
0819, 1285, 1286,
1287, 1289, 1749,
1857, 1858
1392, 1640
0722, 0724
1535
0582, 0702
0573, 0664
0672
1348
0717
Satellite receivers
UltimateTV
Uniden
US Digital
USDTV
Voom
Brand
Code
0772
0216
1109
Initial
Integra
Jaton
AlphaStar
Chaparral
Crossdigital
0571, 0627
1078
1535
0869
Zenith
1856
18
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 19 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
JBL
JSI
JVC
0702
1423
0558, 0623, 0867,
1164
1049, 1051
0790
0490, 0534
0717, 0790, 1020,
1149
0711
0651, 1423
0826
0798, 1173
1533
1127
0591, 0741, 0801,
0869
1058, 1158, 1416,
1440
Sharp
0630, 0675, 0752,
1256
1117
0633, 0770, 1043,
1077
0533, 0839
0869, 1099
0533, 0864, 1033,
1431, 1533
1074
DirecTV
0739
0038, 0039
0000
0037, 0043
0037
0032
0000, 0002, 0037,
0043, 0061, 0121,
0184, 0209,
0212, 0278, 0479,
0593, 1593
0047, 0104
0033, 0035
0000, 0593, 1593
0000
Durabrand
Dynatech
Electrohome
Electrophonic
Emerex
Sharper Image
Sherwood
jWin
Shinsonic
Sonic Blue
Sony
Kawasaki
Kenwood
KLH
Emerson
Sungale
Superscan
SVA
Konka
Koss
0821
0860, 1105
0675, 0821
0675
0790, 0809
0490, 0703
0730
0692
0571
0503, 0695, 1154,
1854
0800, 0803, 0804
0503
0839
0790
1064, 1226
0522
0490, 0539, 0545
0872
0503, 0591, 0741,
0869
1265
Fisher
Fuji
Funai
Garrard
Gateway
GE
Landel
Lasonic
Lecson
Lenoxx
LG
Sylvania
Symphonic
Teac
Technics
Technosonic
Techwood
Theta Digita
Toshiba
1972
0035, 0060, 0065,
0240, 0807
0240, 0432, 0526
0037, 0038
0000
0000
0038, 0075, 0081
0072
0046
1972
0047
0000, 0041, 0042,
0065, 0089, 0105
1972
1972
0042, 0739
LiteOn
Go Video
GoldStar
Gradiente
Harley Davidson
Harman/Kardon
Harwood
Headquarter
Hewlett Packard
HI-Q
Loewe
Magnavox
0511
0503, 0539, 0646,
0675, 0821
0782, 1159
0539
1533
0695, 0831, 1270
0522
0717, 0839
0521, 1521
1082
0591, 0692, 0741
0785
0717
0826
1402
0872, 1003, 1107,
1265
Tredex
Malata
Urban Concepts
US Logic
Venturer
Vizio
Marantz
McIntosh
Memorex
Microsoft
Mintek
Mitsubishi
Momitsu
NAD
NEC
Nesa
Next Base
NexxTech
Norcent
Xbox
Yamaha
Yamakawa
Zenith
Hitachi
Howard Computers
HP
Hughes Network
Systems
Humax
Hush
iBUYPOWER
Jensen
Zoece
0739
1972
1972
0041
VCRs
Brand
ABS
Code
1972
Onkyo
Oritron
Panasonic
0503, 0627, 0792
0651
0490, 0503, 0703,
1362, 1462, 1490,
1762
0503, 0539, 0646,
0675, 1267, 1354
1024
0525, 0571, 0631
1020, 1061, 1086
0539
0770
0675
0672
0522
0778
0651
0522, 0571, 0717,
0790, 0822
0869
1360
0623
0823
0698, 0752
0490, 0573, 0744,
0820, 1044, 1075
0695
0670, 0695, 0873
1158
JVC
KEC
Kenwood
KLH
Kodak
Linksys
Lloyd's
Logik
LXI
Magnasonic
Magnavox
0008, 0041, 0067
0037, 0278
0038, 0041, 0067
0072
0035, 0037
1972
0000
0072
0037
0593
0000, 0035, 0039,
0081, 0149, 0563,
0593
0240
0035, 0081
0037
0035, 0162
1972
0035
0000, 0035, 0037,
0039, 0046, 0047,
0048, 0104,
0162, 0209, 0240,
0479
0043, 0061, 0240
0240
Admiral
Adventura
Aiko
Aiwa
Akai
Alienware
America Action
American High
Asha
Audiovox
Beaumark
Bell & Howell
Broksonic
0048, 0209, 0479
0000
0278
0000, 0037, 0124
0041, 0061, 0175
1972
0278
0035
0240
0037, 0278
0240
Philips
PianoDisc
Pioneer
Polaroid
Polk Audio
Portland
Presidian
Proceed
Proscan
ProVision
Qwestar
RCA
0104
0002, 0121, 0184,
0209, 0479
0037
0035
0081
0072, 0278
0037, 0278
0072
0037, 0047, 0072,
0240
0035, 0041, 0060,
0162
0240
Magnin
Marantz
Marta
Matsushita
Media Center PC
MEI
Calix
Canon
Carver
CCE
Citizen
Colt
Rio
RJTech
Rotel
Rowa
Sampo
Samsung
Memorex
Craig
Curtis Mathes
MGA
Cybernex
CyberPower
Daewoo
Dell
MGN Technology
Microsoft
Mind
1972
0045, 0278
1972
Sansui
Sanyo
Sensory Science
1972
1972
0042, 0105
Minolta
Denon
0042
(continued)
19
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 20 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
Mitsubishi
0043, 0061, 0067,
0075, 0173, 0807
0035, 0048
0000, 0240
0000, 0072
0038, 0040, 0041,
0067, 0104
0037
0034
1972
0240
1972
0035, 0226
0222
0037, 0048, 0104,
0162, 0432, 0593,
1062
0002, 0184, 0209,
0479
0035, 0077, 0162,
0225, 0226, 0616,
1062
0035, 0037, 0038,
0040, 0042, 0240
0042, 0065, 0105
0035
0035, 0081, 0618,
0739, 1081, 1181
0037
Singer
Sonic Blue
Sony
0072
Microsoft
Mind
Niveus Media
Northgate
Panasonic
Philips
1972
1972
1972
1972
0616
0618, 0739
0880
0614, 0616
0614, 0616
0636, 1972
1972
1972
1972
0618, 0636, 0739
1008, 1972
1972
1972
1972
1972
0614, 0616
0000, 0032, 0033,
0034, 0035, 0636,
1032, 1972
1972
Motorola
MTC
Multitech
NEC
Stack 9
STS
Sylvania
0042
RCA
Nikko
Nikon
0000, 0035, 0043,
0081, 0593, 1593
0000, 0593, 1593
1972
1972
0041
0000, 0041
0035, 0162
0000, 0035, 0037
0000
0618, 0636, 0739,
1996
ReplayTV
Sonic Blue
Sony
Symphonic
Systemax
Tagar Systems
Tatung
Niveus Media
Noblex
Northgate
Olympus
Onkyo
Stack 9
Systemax
Tagar Systems
Tivo
Toshiba
Touch
Viewsonic
Voodoo
ZT Group
Teac
Technics
Teknika
Thomas
Tivo
Optimus
Orion
Panasonic
TMK
Toshiba
0240
0043, 0045, 0209,
0210, 0212, 0366,
0845, 1008,
1145, 1972, 1996
0037, 0240
1972
0240
0045
0038, 0040
0040, 0045, 0061
0037
0240
1972
0000
1972
0000, 0035, 0042,
0047, 0048, 0060,
0072, 0081,
0149, 0212, 0240
0072, 0209
0000, 0035, 0072
0038
0000, 0033, 0034,
0039, 0209, 0479,
1139
Cable/PVR Combos
Penney
Brand
Americast
Digeo
Code
0899
1187
Pentax
Philco
Philips
Totevision
Touch
Unitech
Motorola/
General Instrument/
Jerrold
Motorola
Pace
Pioneer
Scientific Atlanta
Sony
Vector
0476, 0810
1187, 1376
0237, 1877
0877, 1877
0877, 1877
1006
Pilot
Vector Research
Video Concepts
Videomagic
Videosonic
Viewsonic
Villain
Pioneer
Polk Audio
Profitronic
Proscan
Protec
Pulsar
Quarter
Quartz
Quasar
RadioShack
Radix
Randex
RCA
0067
0081
0240
0060
0072
0039
0046
0046
Supercable
Zenith
0276
0899
Voodoo
Wards
0035, 0077, 0162
0000
0037
DBS/PVR Combos (1)
Brand
DirecTV
Code
White Westinghouse
XR-1000
Yamaha
0099, 0392, 0639,
1076, 1142, 1377,
1392, 1442,
1443, 1444, 1640
0775, 1505
0775, 1505
0775, 1170, 1505
0775
0037
0042, 0060, 0065,
0077, 0105, 0149,
0240, 0807,
0880
0000, 0035, 0037,
0046, 0047, 0048,
0104
0614, 0616
1972
0034
Zenith
Dish Network System
Dishpro
Echostar
Expressvu
Hughes Network
Systems
Realistic
ZT Group
1972
PVRs
ReplayTV
Ricavision
Ricoh
Runco
Salora
Samsung
Sanky
Sansui
1142, 1442, 1443,
1444
1170
0869
1142, 1442
0392
1392
1442
0639, 1640
0869
Brand
ABS
Code
1972
1972
1972
1972
0739
1972
1972
1972
1972
JVC
0039
0075
Alienware
CyberPower
Dell
Direc TV
Gateway
Hewlett Packard
Howard Computers
HP
Hughes Network
Systems
Humax
Hush
iBUYPOWER
Linksys
Media Center PC
Motorola
Philips
Proscan
RCA
Samsung
Sony
0045, 0240, 0739
0039, 0048
0000, 0041, 0067,
0209, 0479
0046, 0047, 0104,
0159, 0240
0043, 0045, 0121,
0184, 0210, 0212
0000, 0035, 0037,
0042, 0046, 0047,
0104, 0105
0048, 0807, 0848
0072
Sanyo
Scott
Sears
Star Choice
DBS/PVR Combos (2)
0739
0739
1972
1972
1972
1972
Brand
Hughes Network
Systems
Philips
Samsung
Code
Sharp
Shintom
Shogun
0739
0739
0739
0240
20
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 21 Tuesday, June 27, 2006 1:43 PM
Chapter 2: Using the remote control
MTC
NAD
NEC
Nikko
NSM
Onkyo
0420
0019, 0299
0234
0170
0157
0101, 0102, 0138,
0381, 1327
0000, 0032, 0037,
0087, 0420, 0468
0029, 0303, 0388,
0752
Fisher
Harman/Kardon
1801
Audio Amps
0110, 0189, 0891,
1289, 1304, 1306
1273, 1801
0135, 1298, 1320
0110, 1306
1058, 1374, 1495,
1811
0186, 1313, 1569,
1570
1390, 1428
0189
0189, 0531, 1189,
1269, 1514
0189, 1189, 1269,
1289
1289
1189
Brand
Adcom
Bose
Carver
Durabrand
Elan
Code
0577, 1100
0674
0892
1561
0647
0078
0892
0331
0892
1561
0165
0321, 0892
0251
0321
0264
0395, 0823
0246
0892
0823
0892
0823
0395
0321
0264
0689, 0815, 1126
0078, 0211
0331
0078, 0211
0133, 0143, 0354,
0504
Hitachi
Integra
JBL
JVC
Optimus
Kenwood
GE
Panasonic
Harman/Kardon
JVC
KLH
Linn
Magnavox
Parasound
Philips
Pioneer
0420
LeftCoast
Lenoxx
Luxman
Marantz
McIntosh
Nakamichi
NEC
Optimus
Parasound
Philips
Pioneer
PolkAudio
RCA
Realistic
Sansui
0157, 0274, 0626
0032, 0468, 0551,
1062, 1087
0157
0420
0157
0157
0157
0029
0032, 0053, 0420,
0468, 1062
0180, 0420
0157, 0420
0157
0157
0087
0037, 0180
0180
0157
0000, 0100, 0185,
0490, 0604, 0605,
0673, 1364
0157
0157
0420
0180, 0378, 0393,
0420
0029, 0303
0019, 0299
0072
0053, 0157
0036, 0170, 0187,
0490, 1292
Marantz
Polk Audio
Proceed
Proton
QED
Quad
Quasar
RCA
McIntosh
Micromega
Mitsubishi
Myryad
Nakamichi
Onkyo
1393
1189
1313
0135, 0380, 0842,
1298, 1320, 1531
0186, 0531, 1023,
1074
0309, 1288, 1308,
1316, 1350, 1363,
1518, 1548,
1633, 1763, 1764
0189, 1189, 1266,
1269
0014, 0150, 0531,
0630, 1023, 1384
0189, 1289, 1414
1254
0531, 1023, 1074,
1254, 1390, 1511,
1609
1295, 1304, 1500
0189, 1189
1469, 1801
0186
1077
1811
0168, 1058, 1258,
1406, 1441, 1558,
1622, 1658,
1758, 1759, 1858
1023
1313
1074, 1267, 1390,
1528
Optimus
Realistic
Rotel
SAE
Sansui
Sanyo
Panasonic
Shure
Sony
Soundesign
Victor
Wards
Sharp
Philips
Sherwood
Sonic Frontiers
Sony
Pioneer
Yamaha
Polk Audio
Proscan
RCA
Sugden
TAG McLaren
Tascam
CD players
Brand
Adcom
Aiwa
Akai
Code
0234
0124, 0157
0156
0157
0170
0420
0029, 0303
0157, 0299
0003, 0034
0000
0157
0393, 0420
0032
0083, 0157, 0173
0032, 0139
0101
0072, 0655, 1294
0028, 0037, 0190,
0626
0157
0157
0038, 0157
0029, 0038, 0157,
0180, 0435, 0626
0029
Teac
Samsung
Sansui
Sanyo
Sharp
Sherwood
Sirius
Technics
Toshiba
Victor
Wards
Yamaha
Arcam
Audio-Technica
Burmester
California Audio Labs
Carver
Denon
DKK
DMX Electronics
Garrard
Genexxa
Harman/Kardon
Hitachi
Sony
Audio Amps/Tuners
Stereophonics
Sunfire
Teac
Brand
ADC
Aiwa
Code
0531
0121, 0189, 1243,
1388, 1405, 1641
1255, 1512
1390
1077
1074, 1609
1774
1189
1189
1390
0639, 1229, 1253,
1933
0531
0121, 0189, 1189,
1289
Technics
0309, 1308, 1518,
1633
1189
0135
1390
0014, 0189
1406, 1414
0176, 0186, 1176,
1276, 1331, 1375
Akai
Alco
AMC
Anam
Apex Digital
Arcam
Audiotronic
Audiovox
Bose
Integra
JVC
Kenwood
Thorens
Toshiba
Venturer
Wards
XM
Yamaha
Krell
Linn
Magnavox
Marantz
MCS
MGA
Miro
Mission
Mitsubishi
Capetronic
Carver
0083
0000
0157
0083
Delphi
Denon
1414
0121, 1142, 1360
21
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 22 Tuesday, June 27, 2006 1:43 PM
Chapter 3: Menu layout and navigation
Main menu layout
The tables below and on the next page provide a quick overview of your TV’s menu system.
To open the main menus (illustrated below), press Y on the remote control or TV control panel.
Icon
Item
Option
Picture Viewer
S [Launches the JPEG Picture Viewer]
S [Launches the MP3 Audio Player]
S [Launches the Channel Browser™]
S [Opens the TV Guide On Screen™ feature]
Applications
Audio Player
Channel Browser™
TV Guide On Screen™
S [Launches the ATSC Digital CC Selector] (This feature is not available
Digital CC/Audio Selector
CableCARD™
if the TV is not tuned to a digital channel).
S Dynamic list of items provided by Cable company.
(This option is not available if a CableCARD™ is not inserted.)
Picture Settings
S [Opens the Picture Settings menu]
Video
Advanced Picture Settings
S [Opens the Advanced Picture Settings menu]
Theater Settings
S [Opens the Theater Settings menu]
Audio Settings
S [Opens the Audio Settings menu]
Audio
Advanced Audio Settings
S [Opens the Advanced Audio Settings menu]
Audio Setup
S [Opens the Audio Setup menu]
Closed Caption Mode
Closed Caption Advanced
Input Labeling
S OFF/CC1/CC2/CC3/CC4/T1/T2/T3/T4
S [Opens the Closed Caption Advanced menu]
S [Opens the Input Labeling menu]
S English/French/Spanish
Preferences
Menu Language
Channel Browser Setup
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
S [Opens the Channel Browser Setup menu]
S Off/On
Locks
S [Opens the Edit Rating Limits menu]
S [Opens the Channels block menu]
S Off/Video/Video+
Front Panel Lock
GameTimer™
S Off/On
S Off/30 Min/60 Min/90 Min/120 Min
S [Opens the New PIN Code entry screen]
S [Opens the Installation menu (- page 23)]
S [Opens the Sleep Timer menu]
S [Opens the On/Off Timer menu]
S [Opens the PC Setting menu]
S No/Yes
New PIN Code
Installation
Setup
Sleep Timer
On/Off Timer
PC Settings
ColorStream HD1 Audio
HDMI 1 Audio
S Auto/Digital/Analog
ColorStream HD2 Audio
HDMI 2 Audio
S No/Yes
S Auto/Digital/Analog
Slide Show Interval
Quick Restart™
S 2 Sec/5 Sec/10 Sec/15 Sec/20 Sec
S Off/On
22
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 23 Tuesday, June 27, 2006 1:43 PM
Chapter 3: Menu layout and navigation
Setup/Installation menu layout
The Installation menu contains the Terrestrial, Network, TV Guide On Screen™ Setup, Time and Date, and System Status menus
(as described below).
To open the Installation menu (illustrated below), press Y on the remote control or TV control panel, open the Setup menu,
select Installation, and press T.
Icon
Item
Option
Press Y,
open the
Setup menu,
and then
open the
Installation
sub-menu.
Input Configuration
S [Opens the Input Configuration menu]
Terrestrial
S ANT1 S [Scans for new channels on ANT1]
S ANT2 S [Scans for new channels on ANT2]
Channel Program
Channel Add/Delete
Signal Meter
S [Opens the Channel Add/Delete menu]
S [Opens the Signal Meter menu]
Basic Network Setup
S [Opens the Basic Network Setup menu]
Network
E-mail Scheduling Setup S [Opens the E-mail Scheduling Setup menu]
Home File Server Setup
Software Upgrade
S [Opens the Home File Server Setup menu]
S [Opens the Software Upgrade menu]
TV Guide On Screen™ Setup
Time and Date
S [Opens the TV Guide On Screen™ Setup
Start
menu]
Start Setup
S [Opens the Time and Date Setup menu]
System Status
System Information
S [Opens the System Information screen]
23
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 24 Tuesday, June 27, 2006 1:43 PM
Chapter 3: Menu layout and navigation
THINC™ menu layout
The THINC* menu provides access to the Picture Viewer,
Audio Player, Channel Browser, Favorites Browser,
and TV Guide On Screen.
The THINC menu is not part of the main menu system. You
can only view the THINC menu by pressing C on the
remote control.
THINC Applications
Picture Viewer
Audio Player
Channel Browser
Favorites Browser
TV Guide On Screen
Navigate
ENTER
Select
EXIT Exit
* Toshiba Home Interactive Network Connection.
Navigating the menu system
You can use the buttons on the remote control or TV control
panel to access and navigate your TV’s on-screen menu
system.
• Press Y to open the menu system.
• When a menu is open, use the up/down/left/right arrow
buttons (BbC c) on the remote control or TV control panel
to move in the corresponding direction in the menu.
• Press T to save your menu settings or select a highlighted
item. (A highlighted menu item appears in a different color
in the menu.)
• All menus close automatically if you do not make a selection
within 60 seconds, except the signal meter menu, which
closes automatically after about 5 minutes.
• To close a menu instantly, press O.
Note: The menu backgrounds may sometimes appear black,
depending on the signal the TV is receiving. This is not a sign
of malfunction.
Applications
Picture Viewer
Audio Player
Channel Browser
TV Guide On Screen
Digital CC/Audio Selector
CableCARD
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
24
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 25 Tuesday, June 27, 2006 1:43 PM
Chapter 4: Setting up your TV
Selecting the menu language
Configuring the antenna input
sources for the ANT 1 and ANT 2
terminals
You can choose from three different languages (English,
French, and Spanish) for the on-screen display of menus and
messages.
Note: The TV Guide On Screen™ menus are in English,
regardless of the language selected in this menu.
To configure the ANT 1 and ANT 2 input sources:
1
2
Press Y and open the Setup menu.
Highlight Installation and press T.
To select the menu language:
1
2
3
Press Y and open the Preferences menu.
Highlight Menu Language and press c.
Setup
Installation
Press B or b to select your preferred menu language and
press T.
Sleep Timer
On/Off Timer
PC Settings
ColorStream HD1 Audio No
HDMI 1 Audio
Auto
ColorStream HD2 Audio No
Preferences
Closed Caption Mode Off
Closed Caption Advanced
Input Labeling
English
Français
Español
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
3
(A new set of Installation menu icons will appear, as
shown below.) Open the Terrestrial menu, highlight
Input Configuration, and press T.
Menu Language English
Channel Browser Setup
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
Note: The Terrestrial menu may not be accessible (items
will be “grayed out”) in some instances (for example, if a
cable box is connected to the ANT 1 input or if one of the
VIDEO modes is the current input during TV Guide
On Screen™ setup).
4
Press O to close the Preferences menu.
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
4
5
Press B or b to highlight Antenna 1 In, and then press
C or c to select the input source (Cable or Antenna) for
the ANT 1 input on the TV.
Note: If a cable box is connected to the ANT 1 input
during TV Guide On Screen™ setup, the entire Terrestrial
menu will not be accessible, including the input source for
ANT 1, which will automatically display “Cable Box.”
Press b to highlight Antenna 2 In and then C or c to
select the input source (Cable or Antenna) for the
ANT 2 input on the TV, if applicable. If you have not
connected anything to the ANT 2 input, skip this step.
Input Configuration
Antenna 1 In
Antenna In
Cable
2
Antenna
Cancel
Done
6
To save your new settings, highlight Done and press T.
To revert to your original settings, highlight Cancel and
press T.
25
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 26 Tuesday, June 27, 2006 1:43 PM
Chapter 4: Setting up your TV
To program channels automatically:
Programming channels into the
TV’s channel memory
1
Configure the antenna input sources, if you have not
already done so (- page 25).
2
3
Press Y and open the Setup menu.
Highlight Installation and press T.
When you press < or , on the remote control or TV control
panel, your TV will stop only on the channels you programmed
into the TV’s channel memory.
Follow the steps below to program channels into the TV’s
channel memory.
Setup
Installation
Sleep Timer
On/Off Timer
Programming channels automatically
PC Settings
ColorStream HD1 Audio No
HDMI 1 Audio
Auto
Your TV can automatically detect all active channels in your
area and store them in its memory. After the channels are
programmed automatically, you can manually add or erase
individual channels in the channel memory.
ColorStream HD2 Audio No
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
4
(A new set of Installation menu icons will appear, as
shown below.) Open the Terrestrial menu, highlight
Channel Program, and press T.
Note:
• You must configure the antenna input source before
programming channels (- page 25).
• If the Antenna 1 input signal type is set to Cable, the
automatic channel programming process erases channels
that were previously programmed into the TV’s memory.
• If the Antenna 1 input signal type is set to Antenna, the
automatic channel programming process adds newly found
channels to the existing set of programmed channels
(and does NOT erase channels that were previously
programmed into the TV’s memory). To remove an antenna
source channel from the memory, you must manually
delete it.
• To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
• Programming channels when the antenna input is
configured for Cable will take substantially longer than when
the antenna input is configured for Antenna. This is normal;
however, once channel programming is finished, you should
not have to repeat the programming process again unless
your Cable TV service lineup changes significantly.
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
5
6
Highlight ANT 1 (or ANT 2) and then press T to start
automatic channel programming.
ANT 1
Antenna
Scanning channels, please wait ...
52%
Abort
The TV will automatically cycle through all the antenna
channels, and store all active channels in the channel
memory. While the TV is cycling through the channels,
the message “Scanning channels, please wait” appears (as
shown above).
• If you have a CableCARD™ inserted, channel programming
for the ANT 1 input is disabled because the CableCARD™
automatically loads the Cable channel list into the TV’s
channel memory. See the Installation Guide for details on
CableCARD™.
To cancel channel programming, press O on the remote
control (or highlight Abort in the on-screen display and
press T).
When channel programming is finished, press < or , to
view the programmed channels.
26
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 27 Tuesday, June 27, 2006 1:43 PM
Chapter 4: Setting up your TV
To remove a channel from the channel memory:
Highlight the checked box next to the channel number you
want to remove, and then press T to uncheck the box.
Manually adding and deleting channels
in the channel memory
After automatically programming channels into the channel
memory, you can manually add or delete individual channels.
To save your new settings:
Highlight Done and press T.
To add or delete channels in the channel memory:
To revert to your original settings:
Highlight Cancel and press T before saving.
1
2
3
Press Y and open the Setup menu.
Highlight Installation and press T.
(A new set of Installation menu icons will appear, as
shown below.) Open the Terrestrial menu, highlight
Channel Add/Delete, and then press T.
To remove all channels from the channel memory:
Highlight Reset and press T, and then highlight Done and
press T.
Channel Add/Delete
Analog
Digital
Digital
Analog
Analog
Digital
Analog
Analog
Digital
Analog
ANT 1
ANT 2
2
2 - 1
2 - 2
3
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
4
5
6
7
Reset
Cancel
Done
7 - 1
8
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
Note: This action applies to the current antenna input only. To
delete/add channels on the other input, highlight the other
input and press T.
4
The illustration below left shows channels programmed
for the ANT 1 antenna input. To view the list of channels
programmed for the ANT 2 or Cable box antenna input,
press Bb to highlight ANT 2 and press T.
Channel Add/Delete
Channel Add/Delete
Analog
Digital
Digital
Analog
Analog
Analog
Analog
Analog
Digital
Analog
ANT
ANT
1
2
2
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
Analog
ANT
1
1
2
2
2
-
1
2
ANT
2
-
3
3
4
5
6
7
-
4
5
6
7
Reset
Cancel
Done
8
Reset
Cancel
Done
7
1
9
8
10
To add a channel to the channel memory:
Highlight the unchecked box next to the channel number you
want to add, and then press T to check the box.
To manually add digital subchannels on a physical
channel:
Use the Channel Numbers and the Dash (=) on the remote
control to enter the channel number (for example, 56–1).
If the channel is found, the number will be added to the list and
the box will be checked.
If the channel is not found, a message will appear.
27
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 28 Tuesday, June 27, 2006 1:43 PM
Chapter 4: Setting up your TV
Setting the time and date
Setting the ColorStream® HD
audio mode
Note: If you already set up the TV Guide On Screen™ system,
the time and date were set automatically and you can skip this
step.
To set the ColorStream HD audio mode:
To set the time and date:
1
2
Press Y and open the Setup menu.
Highlight ColorStream HD1 Audio (or
ColorStream HD 2 Audio) and press c.
1
2
3
Press Y and open the Setup menu.
Highlight Installation and press T.
(A new set of Installation menu icons will appear, as
shown below.) Open the Time And Date menu,
highlight Start Setup, and press T.
3
Press B or b to select Yes or No and press T to display
the information.
Time And Date
Start Setup
Setup
Installation
No
Sleep Timer
Yes
On/Off Timer
PC Settings
ColorStream HD1 Audio No
HDMI 1 Audio
Auto
ColorStream HD2 Audio No
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
If you have not set up the TV Guide On Screen™ system,
the following screen will appear. To set the time, highlight
TV Guide On Screen™ and press T. The TV Guide
On Screen™ setup sequence will start, and the time and
date will be set automatically.
Note: The analog audio terminals for the ColorStream HD and
HDMI inputs are used in common. When the ColorStream HD
1 (or 2) audio mode is set to Yes, the HDMI 1 (or 2) audio mode
is set to Digital and will be grayed out. When the ColorStream
HD 1 (or 2) audio mode is set to No, the HDMI 1 (or 2) Audio
changes to Auto.
Time And Date
Your TV Guide On Screen system can provide accurate
time and date information.
It is recommended you set up TV Guide On Screen
first and use it to obtain the time and date.
Manual
TV Guide On Screen
Cancel
If you have already set up the TV Guide On Screen™
system, or if you have not set up the time, the Time and
Date setting screen will appear and you will need to
manually set the time and date.
Time And Date
Date (MM/DD/YY)
Time (HH:MM)
0 6 / 3 0 / 0 5
1 1 : 1 1 AM
In the event that your TV Guide On Screen system
has acquired time, the television will use network
acquired time rather than manually enterred time.
Cancel
Done
Note:
• If you highlight TV Guide On Screen™ (above) to set the
time and date through the TV Guide On Screen™ system and
a power outage occurs, the time and date will be updated
automatically when the power is restored.
• If you highlight Manual (above) to set the time and date
manually and a power outage occurs, you will lose the time
and date settings when the power is restored.
• If you manually set the time and date and then perform
TV Guide On Screen™ setup, the manual time and date
settings will be overridden by the TV Guide On Screen™
settings.
28
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 29 Tuesday, June 27, 2006 1:43 PM
Chapter 4: Setting up your TV
Setting the HDMI™ audio mode
Viewing the CableCARD™ menu
A CableCARD™ enables you to view encrypted digital
channels. For connection and subscription information, see
“Connecting a digital CableCARD™” in the Installation
Guide.
To set the HDMI audio mode:
1
2
Press Y and open the Setup menu.
Highlight HDMI 1 Audio (or HDMI 2 Audio) and
press c.
Note: Connecting your TV directly to the Audio/Video output of
your set-top box may provide a more vivid picture.
3
Press b or B to select the HDMI audio mode (Auto,
Digital, or Analog) and press T. (Auto is the
recommended mode.) See “Connecting an HDMI or DVI
device to the HDMI input” (- Installation Guide).
After the CableCARD™ is inserted, a CableCARD™ option
appears in the Applications menu, with informational
screens provided by your digital CableCARD™ service (see
sample illustration under step 3, below).
CableCard Connected -- Acquiring
channel information.
Setup
Installation
CableCard services will only operate
Auto
Sleep Timer
Digital
Analog
with cable signal connected to Antenna 1.
On/Off Timer
PC Settings
ColorStream HD1 Audio No
HDMI 1 Audio
Auto
To view the CableCARD™ menu:
ColorStream HD2 Audio No
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
1
2
3
Press Y and open the Applications menu.
Highlight CableCARD™ and press c.
Note: The ColorStream HD1/HD2 Audio settings influence the
HDMI Audio settings. If ColorStream HD1 (or 2) Audio is set to
No, the HDMI 1 (or 2) Audio setting changes to Auto. If either
ColorStream HD1 (or 2) Audio is set to Yes, the HDMI 1 (or 2)
Audio setting is set to Digital and will be grayed out.
Press Bor b to select one of the side menu items and then
press T to display the information.
Applications
IP Service
Picture Viewer
Audio Player
Conditional Access
CableCARD(tm) Status
Network Setup
Channel Browser
TV Guide On Screen
Digital CC/Audio Selector
CableCARD
CableCARD(tm) Pairing
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
Note: The CableCARD™ menu is for informational
purposes only and has no user-adjustable options.
29
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 30 Tuesday, June 27, 2006 1:43 PM
Chapter 4: Setting up your TV
Setting the Quick Restart™ feature
Viewing the digital signal meter
With the Quick Restart™ feature set to On, the TV will stay in
Standby mode for several minutes after the TV is turned off
(see Note below).
If the TV is turned on from Standby mode, the full picture
appears immediately.
You can view the digital signal meter for the ANT 1 and
ANT 2 digital TV input sources only.
To view the digital signal meter:
1
2
3
Press Y and open the Setup menu.
Highlight Installation and press T.
A new set of Installation menu icons will appear, as shown
below.
To set the Quick Restart™ feature:
1
2
3
Press Y and open the Setup menu.
Highlight Quick Restart and press c.
Open the Terrestrial menu, highlight Signal Meter,
and press T.
Press b or B to select either On or Off and Press T.
Terrestrial
Setup
Input Configuration
Channel Program
Channel Add/Delete
Signal Meter
PC Settings
Off
ColorStream HD1 Audio
HDMI 1 Audio
No
Auto
No
On
ColorStream HD2 Audio
HDMI 2 Audio
Auto
2 Sec
On
Slide Show Interval
Quick Restart
Navigate
ENTER
CH RTN
Back
EXIT Exit
Navigate
ENTER
Select
CH RTN
Back
EXIT Exit
Select
4
Press BbC c to select the antenna input and digital
channel whose signal you want to check.
Note: If Quick Restart is set to Off and you turn off the TV, it
can take several seconds for the picture to appear when you
turn on the TV again. See “Important Notice about Hot Lamp
Restart,” below.
If Quick Restart is set to On and you turn off the TV, the
following will occur for a few minutes:
Note: The physical digital channel number listed in the
Signal Meter screen may not correspond to a virtual TV
channel number. Contact your local broadcasters to
obtain the RF channel numbers for your local digital
stations.
• The screen (lamp) lights dimly; and
• The fans continue to run.
Signal Meter
Signal Locked
This is a function of the Quick Restart Shutdown mode and is
not a TV malfunction. If you do not prefer this, set the Quick
Restart feature to Off.
When the Quick Restart feature is set to Off, if you repeatedly
turn the TV on and off in a short period of time, the useful
service life of the lamp may be shorter than the average useful
service life (- page 84).
0
Peak
0
Antenna
1
4
Physical Digital Channel
Virtual Digital Channel
4-1
Done
To close the screen and return to the Terrestrial
menu:
Highlight Done and press T.
IMPORTANT NOTICE ABOUT HOT LAMP RESTART
When the TV has been powered on long enough for the
lamp unit to get hot, it may take several minutes for the
picture to appear in the following situations:
• When the Quick Restart™ feature is set to Off and you
turn the TV off and then on again within a few minutes;
or
To return to normal viewing:
Press O.
• If the TV is on when a short-term power failure, power
surge, or other similar power failure occurs, such that
the TV loses and regains power within a few minutes.
This is a property of DLP® technology and is NOT a
sign of malfunction.
If this occurs, the yellow LED on the TV front panel will
blink (and the blue LED will be lit solid) until the TV is
finished restarting the lamp and the normal picture
appears. If both LEDs are blinking, you will need to turn
the TV off and then on again to restart the lamp.
30
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 31 Tuesday, June 27, 2006 1:43 PM
Chapter 4: Setting up your TV
Reset Factory Defaults
Viewing the system status
To reset all settings and channels to their factory
default values:
To view the system status:
1
2
Press Y and open the Setup menu.
1
2
3
Press Y and open the Setup menu.
Highlight Installation and press T.
A new set of Installation menu icons will appear, as shown
below right. Open the System Status menu, highlight
System Information, and press T.
Highlight Installation and press T. A new set of
Installation menu icons will appear.
3
4
Open the System Status menu, highlight System
Information, and press T.
Press C c to scroll through the menu bar to select
Factory Defaults.
System Status
Setup
Installation
System Infomation
5
6
Enter your PIN code (or 0000 if no PIN code has been set).
Sleep Timer
On/Off Timer
Highlight Yes and press T. The TV will turn off
automatically after a few seconds. After the TV turns off,
unplug the TV power cord and then plug it in again to
complete the reset process.
PC Settings
ColorStream HD1 Audio No
HDMI 1 Audio
Auto
ColorStream HD2 Audio No
Navigate
ENTER
CH RTN
Back
EXIT Exit
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
Select
System Information
4
Press C c to scroll through the menu bar to select either
Product Information or Software Version and view
the related information.
Press YES to confirm. After the TV
turns off, unplug it and plug it back
in to complete the reset.
System Information
System Information
Sun Jan 1, 2006 12:12:19am
No
Yes
Product Information
Software Version
Brand: Toshiba
Model: 62MX196
2.2.34.0
2006 11:05:49
Mar
1
-
FW: 24
To cancel the reset:
Highlight No and press T.
Done
Done
Note: If you previously set the TV to High Bright mode and
then restore the factory defaults, the TV will default to Low
Power mode. To set the TV back to High Bright mode, see
page 57.
To close the screen and return to the Installation
menu:
Highlight Done and press T.
To return to normal viewing:
Press O.
31
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 32 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Selecting the video input source
to view
Labeling the video input sources
You can label each video input source to describe the type of
device you connected to each source. You can choose from the
following preset list of labels:
• “– –” (default label)
• Cable
The video inputs available to view will be determined by the
input terminals you used to connect your devices
(see the Installation Guide).
• DTV
• Satellite/DSS
To select the video input source to view:
• VCR
• Laser Disk
• DVD
• HD DVD
• Audio Receiver
• Compact Disc
• Video Recorder
• Game Console
1
2
Press + on the remote control or TV control panel.
And then either:
a) Press 0-8; or
b) Repeatedly press Bb on the remote control (or
CHANNEL U u on the control panel) to change the
input; or
c) Repeatedly press + on the remote control or TV
control panel to change the input.
• Hide (to skip over an unused input in the Input Selection
The current signal source displays in the top right corner
of the Input Selection screen.
screen)
Note:
• If you select ANT 2 in the Input selection screen, you can
Input Selection
ANT 1
choose only “– –” or “Hide” as the label.
0
1
2
3
4
5
6
7
8
ANT 1
Video 1
• If you select PC in the Input Selection screen, you can
choose only “– –,” “Hide,” or “Game Console” as the label.
Video 2
ColorStream HD1
ColorStream HD2
HDMI 1
To label the video input sources:
HDMI 2
PC
1
2
3
Press Y and open the Preferences menu.
Highlight Input Labeling and press T.
Press B or b to highlight the video source you want to
label.
ANT 2
0
8
INPUT to Select
-
/
Note:
• You can label the video input sources according to the
specific devices you have connected to the TV
(- “Labeling the video input sources” at right).
• The source can be “hidden” (- “Labeling the video input
sources” at right).
Preferences
Closed Caption Mode
Off
Closed Caption Advanced
Input Labeling
Menu Language
English
Channel Browser Setup
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
Input Labeling
Video 1
Video 2
DVD
Cable
ColorStream HD 1
ColorStream HD 2
HDMI 1
Video Recorder
Hide
DTV
HDMI 2
Satellite/DSS
--
--
PC
ANT 2
Reset
Done
4
Press C or c to select the desired label for that input
source. If a particular input is not used, you can select
Hide as the label, which will cause that input to be
“grayed out” in the Input Selection screen and skipped
over when you press + on the remote control.
32
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 33 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
5
To save the new input labels, highlight Done and
Tuning channels
press T.
To revert to the factory default labels, highlight Reset
and press T.
Tuning channels using the
Channel Browser™
Input labeling example:
The screen below left shows the default Input Selection
screen (with none of the inputs labeled as a specific device).
The screen below right is an example of how you could label
the inputs if you connected a DVD player to VIDEO 1, Cable
TV to VIDEO 2, a video recorder to ColorStream HD1, a DTV
set-top box to HDMI 1, and a satellite/DSS set-top box to
HDMI 2. Also note that the ColorStream HD2 input is labeled
“Hidden,” which means that input will be skipped over when
+ is pressed.
The Channel Browser™ provides an easy navigation interface
for all your channels and inputs. This feature allows you to:
• Navigate the contents of all of your inputs.
• Keep a list of your favorite channels (see “Favorite
Browser” below).
• Provide Cable Box and Satellite Box lists.
• Keep a history of the last 32 channels or inputs viewed.
• Quickly surf and tune your recently viewed channels/inputs
from the Channel Browser™ History List (illustrated on the
next page).
• Surf via Browse mode (to immediately tune channels as you
highlight them in the Channel Browser™) or Select mode (to
surf over channels in the Channel Browser™ before you
select one to tune).
Input Selection
ANT 1
Input Selection
ANT 1
0
1
2
3
4
5
6
7
8
ANT 1
0
1
2
3
4
5
6
7
8
ANT 1
Video 1
DVD
Video 2
Cable
ColorStream HD1
ColorStream HD2
HDMI 1
Video Recorder
ColorStream HD2 (Hidden)
DTV
HDMI 2
Satellite/DSS
PC
PC
ANT 2
ANT 2
• Quickly change inputs from the Inputs List.
0
8
INPUT to Select
-
/
0
8
-
/
INPUT to Select
Input Selection screen with
no inputs labeled.
Input Selection screen with
all inputs labeled except input 4,
which has been hidden.
Favorite Browser
The Favorite Browser allows you to quickly set up a favorite
channels/inputs list that is integrated into the Channel Browser™.
To clear the input labels:
To add a favorite channel/input:
1
2
3
Press Y and open the Preferences menu.
Highlight Input Labeling and press T.
Highlight Reset and press T.
1
2
Tune to the channel or input.
Press and hold n for 3 seconds.
Note: Additions are added to the beginning of the Favorite list
on the left side of the Channel Browser™.
To delete a favorite channel/input:
1
2
Press n to open the Favorite browser list.
Highlight the channel or input to delete by pressing
3 C or # c.
3
Press and hold = for 3 seconds. The channel/input will
be removed from the Favorite list.
Picture Preview
• A small thumbnail preview of the current channel or input
will appear in the list.
• Picture snapshots will be taken when a source change occurs
from the Channel Browser™.
• Up to 32 picture previews can be stored in the Channel
Browser across all lists. If you add a new picture when the
total = 32, the oldest thumbnail will be deleted.
One thumbnail is counted only once against the total, no
matter how many times it appears in various lists.
• Turning off the TV deletes all of the current thumbnails.
(continued)
33
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 34 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
To set up the Channel Browser™:
Elements of the Channel Browser™
1 2
1
2
3
Press Y and open the Preferences menu.
Highlight Channel Browser Setup and press T.
Press B to highlight Navigation, and then press C or c
to select either Browse Mode or Select Mode.
3
10
HDMI 1
ClrStrmHD1
__
78
4-1
4
8
1
1
1
History
ANT 1
CABLE
AAA
480i
Channel Browser
Channel Browser Setup
Navigation
History List
ANT1 List
Select Mode
Power Off Clear (On)
On
On
Off
On
On
On
4
5
6
7
8
9
ANT2 List
Cable Box List
Satellite Box List
Inputs List
1
2
3
4
Input type
Highlighted item (channel or input)
Favorites List
Reset
Done
Channels with thumbnails stored in the History List
4
Press b to highlight History List, and then press C or c
to select the setting you prefer: either Power Off Clear
(On), On, or Off.
Current list (History, ANT 1, ANT 2, Cable Box,
Satellite Box, Inputs, or Favorites)
5
6
7
8
9
Current input
Note: When History List is set to On, the channels and
inputs stored in the list will be saved every power on/off
cycle. When History List is set to Power Off Clear (On),
the channels and inputs stored in the list will be cleared
with every power on/off cycle of the TV.
Current antenna type (cable or TV)
Active channel number
Channel call letters (if available)
Resolution
5
6
7
8
9
Press b to highlight ANT1 List, and then press C or c to
select On or Off.
To toggle among the available lists:
Press b to highlight ANT2 List, and then press C or c to
select On or Off.
After opening the Channel Browser™, press B or b to toggle
among History, ANT 1, ANT 2, Cable Box, Satellite Box,
Inputs and Favorites.
Press bto highlight Cable Box List, and then press Cor
c to select On or Off.
Note:
• The Channel Browser™ opens the History List by default.
Once another list has been selected, the Channel Browser™
will open the last selected list.
• If all lists are turned off, pressing 3 C, # c, or n will not
display the Channel Browser™. If Favorites List is turned
off, n will have no effect.
• Pressing n will bring up the Channel Browser™ Favorite
list regardless of the last selected list in the
Channel Browser™.
Press b to highlight Satellite Box List, and then press
C or c to select On or Off.
Press b to highlight Inputs List, and then press C or c
to select On or Off.
10 Press b to highlight Favorites List, then press Cor c to
select On or Off.
11 To save your entries, highlight Done and press T.
To return to factory defaults, highlight Reset and
press T.
To tune to a channel or input in Browse mode:
Note: Cable Box List and Satellite Box List will be
grayed out and set to Off by default. They will remain this
way until a Cable Box and/or Satellite Box is configured
from the TV Guide setup.
1
While watching TV, press 3 C or # c to open the
Channel Browser™ and surf back to a previous item or
forward to the next item in the list.
In Browse mode, when you stop on an item in the
Channel Browser™, it will be highlighted and the TV will
automatically tune to the channel or input.
Press O to close the Channel Browser™.
Note: The Channel Browser™ will close automatically if
you do not make a selection within 30 seconds.
To open the Channel Browser™:
• Press 3 C, # c, or n on the remote control.
• Press 3 C to surf backward through the currently selected
list.
2
• Press # c to surf forward through the currently selected list.
Note: The Channel Browser™ is not available while the TV is in
POP mode.
34
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 35 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
To tune to a channel or input in Select mode:
Tuning to the next programmed channel
1
While watching TV, press 3 C or # c to open the
Channel Browser™ and surf back to a previous item or
forward to the next item in the list.
To tune to the next programmed channel:
Press < or , on the remote control or TV control panel.
Note: This feature will not work unless you program channels
into the TV’s channel memory (- page 26).
In Select mode, when you stop on an item in the
Channel Browser™, it will be highlighted but you must
press T to tune the TV to the highlighted item.
Press O to close the Channel Browser™.
Tuning to a specific channel (programmed
or unprogrammed)
2
Adding and clearing channels and inputs in the
History List
Tuning analog channels:
Press the Channel Number buttons (0–9) on the remote
control. For example, to select channel 125, press 1, 2, 5.
ANT 1
Satellite..
Video
2
ClrStrmHD1
__
ClrStrmHD2
__
HDMI 1
1
Inputs
ANT 1
CABLE
4
AAA
480i
Channel Browser
Tuning digital channels:
Press the Channel Number (0–9) on the remote control,
followed by the dash (=) and then the sub-channel number.
For example, to select digital channel 125-1, press 1, 2, 5, –, 1.
Adding channels and inputs to the History List:
As a channel or input is tuned, the Channel Browser™ adds it
to the History List and displays it on the “right side” of the
Channel Browser™. Previously tuned channels/inputs are
“shifted” to the left, eventually moving off the left side. Press
3 C to surf backward through the previously tuned channels/
inputs. Any channel or input that is tuned repeatedly will not
be repeated in the History List, but instead is moved to the end
of the list on the right side of the Channel Browser™.
Note: If a digital channel is not programmed—either through
the automatic channel scan (- page 26) or the channel add/
delete function (- page 27)—you will have to tune the RF
channel using the Channel Numbers and dash (=) on the
remote control.
The Channel Browser™ will store the following channels:
• All channels that are tuned using the numeric buttons on the
remote control.
• All channels that are tuned using < or , on the remote
control for at least 5 seconds.
• All inputs that are tuned for at least 5 seconds.
Note: Whenever an item is selected that cannot be tuned (for
various reasons), the TV will automatically tune to the
previously viewed channel or input.
Clearing channels from the History List:
• Reconfiguring the ANT 1 or ANT 2 input will clear the
History List.
Note: See page 25 for details on configuring the antenna
inputs.
• Removing the CableCARD™ will clear the History List.
• Once 32 channels or inputs are stored in the History List, the
oldest item will be removed from the list when a new
channel or input is tuned.
• If History List in the Channel Browser Setup is set to
“Power Off Clear (On),” turning off the TV will clear the
History List.
35
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 36 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Switching between two channels using
Channel Return
Switching between two channels using
SurfLock™
The Channel Return feature allows you to switch between two
channels without entering an actual channel number each time.
The SurfLock™ feature temporarily “memorizes” one channel
in the R button, so you can return to that channel quickly
from any other channel by pressing R.
1
2
Select the first channel you want to view.
To memorize a channel in the R button:
Select a second channel using the Channel Number
buttons (and the dash (=) button if selecting a digital
channel).
1
2
Tune the TV to the channel you want to program into the
R button.
Press and hold R for about 2 seconds until the message
“Channel Memorized” appears on-screen. The channel
has been programmed into the R button.
3
Press R on the remote control. The previous channel
will be tuned. Each time you press R, the TV will switch
back and forth between the last two channels that were
tuned.
3
You can then change channels repeatedly, and when you
press R, the memorized channel will be tuned.
Note: If you press R from a non-antenna input, the TV
will return to the last-viewed ANT input and channel.
The TV will return to the memorized channel one time only.
Once you press R and then change channels again, the
CH RTN memory will be cleared and the button will function
as Channel Return, by switching back and forth between the
last two channels that were tuned.
36
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 37 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Note: If you select one of the TheaterWide® picture sizes, the
top and bottom edges of the picture (including subtitles or
captions) may be hidden. To view the hidden edges, either
scroll the picture (TheaterWide 2 and 3 only) or try viewing the
program in Full or Natural picture size.
Selecting the picture size
You can view many program formats in a variety of picture
sizes—Natural, TheaterWide 1, TheaterWide 2,
TheaterWide 3, and Full.
Natural picture size
• The image is displayed close to its originally formatted
proportion. Some program formats will display with
sidebars and/or bars at the top and bottom.
Note: The “picture size” illustrations are examples only. The
format of the image (in any of the picture sizes) will vary
depending on the format of the signal you are currently
watching. Select the picture size that displays the current
program the way that looks best to you.
You can save separate picture size preferences for each input
on your TV.
To select the picture size using the remote control:
1
2
Press I on the remote control.
While the Picture Size screen is open, you can do one of
the following to select the desired picture size:
Natural picture size example
TheaterWide 1 picture size (for 4:3 format programs)
• Repeatedly press I.
• The center of the picture remains close to its original
proportion, but the left and right edges are stretched wider to
fill the screen.
• Press the corresponding Number button (0-4) while the
Picture Size screen is open.
• Press B or b while the Picture Size screen is open.
Picture Size
0
1
2
3
4
Natural
TheaterWide 1
TheaterWide 2
TheaterWide 3
Full
TheaterWide 1 picture size example
0
4
PIC SIZE
to Select
-
/
TheaterWide 2 picture size (for letter box programs)
• The picture is stretched wider to fill the width of the screen,
but only slightly stretched taller.
• The top and bottom edges of the picture may be hidden. To
view the hidden areas, see “Scrolling the TheaterWide®
picture” on the next page.
To select the picture size using the menus:
1
2
Select Picture Size in the Theater Settings menu.
Select the input for which you want to save your picture
settings.
3
Highlight Done and press T.
Theater Settings
Picture Size
Natural
Picture Scroll
Cinema Mode
Auto Aspect Ratio
--
Film
On
A B C D E F G - - - - - - - - - - - - - - - -
TheaterWide 2 picture size example
Reset
Done
Note: Full picture size may not be available for some program
formats (it will be “grayed out” in the Picture Size screen).
Using these functions to change the picture size (i.e.,
changing the height/ width ratio) for any purpose other than
your private viewing may be prohibited under the Copyright
Laws of the United States and other countries, and may
subject you to civil and criminal liability.
(continued)
37
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 38 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
TheaterWide 3 picture size (for letter box programs
with subtitles)
• The picture is stretched wider to fill the width of the screen,
but only slightly stretched taller.
Scrolling the TheaterWide® picture
(TheaterWide 2 and 3 only)
• The top and bottom edges are hidden. To view the hidden
areas (such as subtitles or captions), see “Scrolling the
TheaterWide® picture,” at right.
You can set separate scroll settings for the TheaterWide 2 and
TheaterWide 3 modes for each input.
To set the scroll settings:
1
2
Press Y and open the Video menu.
Highlight Theater Settings and press T.
A B C D E F G - - - - - - - - - - - - - - - -
A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -
TheaterWide 3 picture size example
Video
Picture Settings
Advanced Picture Settings
Theater Settings
Full picture size (for 16:9 [480i, 480p] source
programs only)
• If receiving a squeezed 4:3 format program, the picture is
stretched wider to fill the width of the screen, but not
stretched taller.
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
3
In the Picture Size field, select either TheaterWide 2
or TheaterWide 3 (you cannot scroll in any other mode).
• None of the picture is hidden.
4
5
Press b to highlight the Picture Scroll field.
Press C or c to scroll the picture up and down as needed,
from –10 to +20.
Theater Settings
Picture Size
TheaterWide 2
Full picture size example
Picture Scroll
Cinema Mode
Auto Aspect Ratio
-5
Film
On
Reset
Done
6
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
38
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 39 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Using the auto aspect ratio feature Selecting the cinema mode
(480i signals only)
When the auto aspect ratio feature is set to On, the TV will
automatically select the picture size when one of the following
When you view a DVD (480i signal; 3:2 pulldown processed)
input sources is received:
from a DVD player connected to the VIDEO 1, VIDEO 2,
• A 480i signal from the VIDEO 1, VIDEO 2, ColorStream
HD-1, or ColorStream HD-2 input.
• A 1080i, 480i, 480p, or 720p signal from the HDMI input.
ColorStream HD-1, ColorStream HD-2 (component
video), or HDMI input on the TV, smoother motion can be
obtained by setting the Cinema Mode to Film.
Aspect ratio of Automatic aspect size (automatically
signal source selected when Auto Aspect is On)
To set the Cinema Mode to Film:
4:3 normal
Natural (with sidebars)
1
2
3
Press Y and open the Video menu.
Highlight Theater Settings and press T.
In the Cinema Mode field, select Film.
4:3 letter box TheaterWide 2
16:9 full
Full
Not defined
Theater Settings
(no ID-1 data The current picture size you set under
Picture Size
Natural
or HDMI
aspect data)
“Selecting the picture size” on page 37.
Picture Scroll
Cinema Mode
Auto Aspect Ratio
--
Film
On
Note: The auto aspect ratio feature is not applicable to
antenna or cable input sources.
Reset
Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
To turn on the auto aspect ratio feature:
1
2
3
Press Y and open the Video menu.
Highlight Theater Settings and press T.
In the Auto Aspect Ratio field, select On.
To set the Cinema Mode to Video:
Select Video in step 3 above.
Theater Settings
Picture Size
Natural
Picture Scroll
Cinema Mode
Auto Aspect Ratio
--
Film
On
Reset
Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
To turn off the auto aspect ratio feature:
Select Off in step 3 above.
39
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 40 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
• If you labeled all of the inputs as HIDE (-page 32), the
POP feature will be disabled and the message “Not
Available” will appear if you try to open the POP double-
window.
Using the POP features
• The message “Not Available” will appear If you try to
open the POP double-window when the Input Lock
feature is in Video or Video+ mode.
Using the POP double-window feature
The POP (picture-out-picture) double-window feature splits
the screen into two windows so you can watch two programs
at the same time.
To tune to the highlighted window (and close the POP
double-window):
To display a program in the POP window:
Press T after highlighting the window you want to view as a
normal picture.
1
Press P to open the POP double-window.
Notes about recording:
POP double-window
• If the POP window is open and you attempt to start
recording, the POP window will close before recording
starts.
• If you use the TV’s remote control to start recording, you will
not be able to open the POP window and the message “Not
Available” will appear if you try to do so.
• It is recommended that you use the TV’s remote control to
start recording. If you use a device other than the TV’s
remote control to start recording, you may accidentally open
the POP window during the recording process. If this
happens, the recorded audio will reflect the audio of the
active window (left or right), which may not be the audio you
intended to record.
ANT1
12
POP
ColorStream HD1
Left window
Right window
Green border
(denotes active window)
2
3
Press C or c to highlight the desired window. When
highlighted, the window will have a green border.
Press + to open the Input Selection window. Select
the input source for the POP window by pressing the
corresponding Number button (0–8). The current source
displays in red.
Left window
Right window
Input Selection
ANT 1
Input Selection
ColorStream HD1
0
1
2
3
4
5
6
7
8
ANT 1
0
1
2
3
4
5
6
7
8
ANT 1
Video 1
Video 1
Video 2
Video 2
ColorStream HD1
ColorStream HD2
HDMI 1
ColorStream HD1
ColorStream HD2
HDMI 1
HDMI 2
HDMI 2
PC
PC
ANT 2
ANT 2
0
8
INPUT to Select
-
/
0
8
-
/
INPUT to Select
Left window — ANT 1 and ANT 2 inputs are selectable.
Right window — ColorStream HD1 and HD2 (only for
480p,1080i and 720p) and HDMI 1 and 2 are selectable.
Note:
• The message “Current video format cannot be
displayed” will appear if you press P when the TV is
in ColorStream HD1 or HD2 mode and is receiving a
480i format signal.
• The FREEZE feature is not available when the POP
double-window is open. If you press B when the POP
double-window is open, the message “Not available
from current video mode” will appear.
40
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 41 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Selecting the POP window audio out
Using the FREEZE feature
While the POP double-window is open, press C or c to select
which audio (left or right POP window) to be output from the
TV speakers (and also from the VARIABLE AUDIO OUT
and A/V AUDIO OUT terminals).
To use the FREEZE feature:
1
2
When viewing the TV, press B to make the picture a
The window with the active audio is outlined with a green
border.
still picture.
To return to the moving picture, press B again (or any
Example: Press
other button).
Note:
• The FREEZE feature is not available when the POP
double-window is open. If you press B, the message
“Not available from current video mode” will appear.
• If the TV is left in FREEZE mode for more than 15
minutes, the FREEZE mode will automatically be
released and the TV will return to the moving picture.
Example: Press
Moving picture
Still picture
POP double-window aspect ratio
The POP double-window feature displays each picture
according to its input signal aspect ratio, as illustrated in the
examples below.
Using the FREEZE function for any purpose other than your
private viewing may be prohibited under the Copyright Laws
of the United States and other countries, and may subject
you to civil and criminal liability.
480i
480i
480p/720p/
1080i
480i
Note:
• The auto aspect ratio feature (- page 39) does not operate
in POP double-window mode.
• Aspect ratio is the ratio of width to height of the picture.
41
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 42 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Adjusting the picture quality
You can adjust the picture quality (contrast, brightness, color,
tint, and sharpness) to your personal preferences.
Adjusting the picture
Selecting the picture mode
Selection
contrast
brightness
color
Pressing C
lower
Pressing c
higher
You can select your desired picture settings from four different
modes, as described below.
darker
paler
lighter
Mode
Picture Quality
deeper
Sports
Standard
Bright and dynamic picture (factory setting)
Standard picture settings (factory setting)
tint
reddish
softer
greenish
sharper
sharpness
Lower contrast for darkened room (factory
setting)
Movie
To adjust the picture quality:
Preference
Your personal preferences
1
2
3
Press Y and open the Video menu.
Highlight Picture Settings and press T.
Press B or b to select the picture quality you want to
adjust (Contrast, Brightness, Color, Tint, or
Sharpness), and then press Cand cto adjust the setting,
as described in the table above.
To select the picture mode:
1
2
3
Press Y and open the Video menu.
Highlight Picture Settings and press T.
In the Mode field, select the picture mode you prefer.
Picture Settings
ANT 1
Picture Settings
ANT 1
Mode
Sports
Mode
Sports
Contrast
Brightness
Color
100
50
50
0
Contrast
Brightness
Color
100
50
50
0
Tint
Tint
Sharpness
50
Sharpness
50
Reset
Done
Reset
Done
Picture Settings
Mode: Preference
Picture Settings
Mode: Standard
Standard
Contrast
70
Mode
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Note:
The picture qualities you adjusted are automatically saved in
the Preference mode (- “Selecting the picture mode,”
at left).
• The picture mode you select affects the current input
only (ANT 1 in the example above). You can select a
different picture mode for each input.
• If you select one of the factory-set picture modes
(Sports, Standard, or Movie) and then change a
picture quality setting (for example, increase the
contrast or change the color temperature), the picture
mode automatically changes to Preference in the
Picture Settings menu.
• If you previously set the TV to High Bright mode, and
chose Reset in item 4 above, the TV will default to Low
Power mode. To set the TV back to High Bright mode,
see page 57.
42
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 43 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Closed Caption Advanced
You can customize the closed caption display characteristics
by changing the background color, text size, type, edge, and
color.
Using the closed caption mode
The closed caption mode has two options:
• Captions—An on-screen display of the dialogue, narration,
and sound effects of TV programs and videos that are closed
captioned (usually marked “CC” in program guides).
• Text—An on-screen display of information not related to
the current program, such as weather or stock data (when
provided by individual stations).
Note:
• This feature is available for digital channels only.
• You cannot set the Caption Text and Background as the
same color.
To customize the closed captions:
To view captions or text:
1
2
Press Y and open the Preferences menu.
Highlight Closed Caption Advanced and press T.
Closed Caption Advanced
1
2
3
Press Y and open the Preferences menu.
Highlight Closed Caption Mode and press c.
Caption Size
Auto
Auto
Auto
Auto
Auto
Press Bor bto select the desired closed caption mode and
press T.
Caption Text Type
Caption Text Edge
Caption Text Color
Background Color
Preferences
Reset
Done
Closed Caption Mode Off
Closed Caption Advanced
Input Labeling
Off
CC1
CC2
CC3
CC4
T1
3
4
Press B or b to highlight the characteristic you want to
change, and then press C or c to select the format for that
characteristic (see table below).
Menu Language
English
Channel Browser Setup
T2
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
• To view captions:
Highlight CC1, CC2, CC3, or CC4. (CC1 displays
translation of the primary language in your area.)
Caption Size Auto, Small, Standard, Large
Auto, Default, Mono w. Serif, Prop. w. Serif,
Mono w/o Serif, Prop. w/o Serif, Casual,
Cursive, Small Capitals
Caption Text
Type
Caption Text Auto, None, Raised, Depressed, Uniform,
Edge Left Drop Shadow, Right Drop shadow
Giant pandas eat leaves.
Caption Text Auto, Black, White, Red, Green, Blue,
Note: If the program or video you selected is not closed
captioned, no captions will display.
Color
Yellow, Magenta, Cyan
• To view text:
Highlight T1, T2, T3, or T4.
Background
Color
Auto, Black, White, Red, Green, Blue,
Yellow, Magenta, Cyan
WORLD WEATHER
Temps
Current
Weather
Clear
F
C
LONDON
MOSCOW
PARIS
51
57
53
66
65
11
14
12
19
18
Cloudy
Clear
Cloudy
Rain
ROME
TOKYO
Note: If text is not available in your area, a black rectangle
may appear on-screen. If this happens, set the Closed
Caption Mode to Off.
• To turn off the Closed Caption mode:
Select Off in step 3 above.
Note: A closed caption signal may not display in the following
situations:
• When a videotape has been dubbed
• When the signal reception is weak
• When the signal reception is non-standard
43
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 44 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Digital closed captions
You can use the Digital CC/Audio Selector to select digital
closed caption services (if available), which will temporarily
override regular closed captions on digital channels (only).
When such services are not available, the Digital CC/Audio
Selector presents a default list of services. If the selected
service is not available, the next available service will be used
instead.
Adjusting the audio
Muting the sound
Press W to partially reduce (1/2 MUTE) or turn off (MUTE)
the sound. Each time you press W, the mute mode will
change in the following order:
1/2 Mute
Mute
Volume
To select digital closed captions:
If the closed caption mode is set to Off when you select MUTE
mode, the closed caption feature is automatically activated. To
mute the audio without automatically activating the closed
caption feature, use Z to set the volume to 0. See “Using the
closed caption mode” (- page 43) for more information on
closed caption modes.
1
2
Press Y and open the Applications menu.
Highlight Digital CC/Audio Selector and press T.
Applications
Picture Viewer
Audio Player
Channel Browser
Using the digital audio selector
TV Guide On Screen
Digital CC/Audio Selector
CableCARD
You can use the Digital Audio Selector to conveniently switch
between audio tracks on a digital channel (for those channels
that have multiple audio tracks). This temporarily overrides the
audio track chosen by the language option under Audio
Setup (- “Selecting stereo/SAP broadcasts” on page 45).
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
3
4
Press B or b to select Closed Caption, and then press
C or c to select the desired service.
To use the digital audio selector:
Closed Caption
Audio
CC 1
None
1
2
Press Y and open the Applications menu.
Highlight Digital CC/Audio Selector and press T.
Press O.
Using the Closed Caption button on
the remote control
Applications
Picture Viewer
Audio Player
Channel Browser
If you press ; when an analog channel is tuned:
• The CC selector will be active and will display CC1-4 and
T1-4 as the options.
TV Guide On Screen
Digital CC/Audio Selector
CableCARD
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
• The audio selector will be disabled.
3
4
Press B or b to select Audio, and then press C or c to
If you press ; when a digital channel is tuned:
select the desired service.
• The CC selector will be active and will display the possible
caption options (available languages) for that channel or
service. For example, in addition to English, a channel
might offer closed captions in Spanish and/or French.
Closed Caption
Audio
CC 1
None
Press O.
• The audio selector will be active and will offer different
audio choices for the digital channel (Dolby or AC3, for
example).
44
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 45 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
To listen to an alternate language on an ATSC digital
station (if available):
Highlight the Language field in step 3 at left, and then press
C or c to select the language you prefer.
Selecting stereo/SAP broadcasts
The multi-channel TV sound (MTS) feature allows you to
output high-fidelity stereo sound. MTS also can transmit a
second audio program (SAP) containing a second language,
music, or other audio information (when provided by
individual stations).
Adjusting the audio quality
You can adjust the audio quality by adjusting the bass, treble,
and balance.
When the TV receives a stereo or SAP broadcast, the word
“STEREO” or “SAP” appears when E is pressed. The MTS
feature is not available when the TV is in VIDEO mode.
To adjust the audio quality:
To listen to stereo sound:
1
2
3
Press Y and open the Audio menu.
Highlight Audio Settings and press T.
Press b or B to highlight the item you want to adjust
(Bass, Treble, or Balance).
1
2
Press Y and open the Audio menu.
Highlight Audio Setup and press T.
Audio Settings
Audio
Audio Settings
Bass
100
100
0
Advanced Audio Settings
Audio Setup
Treble
Balance
StableSound
Off
Done
3
4
In the MTS field, select Stereo.
Reset
Audio Setup
4
5
Press C or c to adjust the level.
MTS
Stereo
English
Language
• C makes the bass or treble weaker or increases the
balance in the left channel (depending on the item
selected).
• c makes the bass or treble stronger or increases the
balance in the right channel (depending on the item
selected).
Speakers
On
Optical Output Format
Dolby Digital
Reset
Done
To save the new settings, highlight Done and press T.
To reset the settings to the factory defaults, highlight
Reset and press T.
To save the new settings, highlight Done and press T.
To reset the settings to the factory defaults, highlight
Reset and press T.
Note:
• You can typically leave the TV in Stereo mode,
because it will automatically output the type of sound
being broadcast (stereo or monaural).
• If the stereo sound is noisy, select Mono to reduce the
noise.
To listen to a second audio program on an analog
station (if available):
Select SAP in step 3 above.
Note:
• A second audio program (SAP) can be heard only on those
TV stations that offer it. For example, a station might
broadcast another language as a second audio program. If
you have SAP on, you will see the current program on the
screen but hear the other language instead of the program’s
normal audio.
• If you have SAP on and the station you are watching is not
broadcasting a second audio program, the station’s normal
audio will be output. However, occasionally there is no
sound at all in SAP mode. If this happens, set the MTS
feature to Stereo mode.
45
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 46 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Using the StableSound® feature
Selecting the optical audio output format
The StableSound® feature limits the highest volume level to
prevent extreme changes in volume when the signal source
changes (for example, to prevent the sudden increase in
volume that often happens when a TV program switches to a
commercial).
You can use this feature to select the optical audio output
format when you connect a Dolby Digital decoder or other
digital audio system to the Optical Audio Out terminal on
the TV (- “Connecting a digital audio system” in the
Installation Guide).
To turn on the StableSound® feature:
To select the optical audio output format:
1
2
3
Press Y and open the Audio menu.
Highlight Audio Settings and press T.
In the StableSound field, select On.
Audio Settings
1
2
3
Press Y and open the Audio menu.
Highlight Audio Setup and press T.
In the Optical Output Format field, select either
Dolby Digital or PCM, depending on your device.
Bass
100
100
0
Audio Setup
Treble
MTS
Stereo
English
Balance
StableSound
Language
On
Done
Speakers
On
Reset
Optical Output Format
Dolby Digital
Reset
Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Note: The RESET function returns your audio adjustments
to the following factory settings:
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Bass . . . . . . . . . center (50)
Treble. . . . . . . . center (50)
Balance . . . . . . center (0)
StableSound. . . Off
To turn off the StableSound feature:
Select Off in step 3 above.
Turning off the built-in speakers
You can use this feature to turn off the TV speakers when you
connect an audio system to your TV (- “Connecting a digital
audio system” and “Connecting an analog audio system” in the
Installation Guide).
To turn off the built-in speakers:
1
2
3
Press Y and open the Audio menu.
Highlight Audio Setup and press T.
In the Speakers field, select Off.
Audio Setup
MTS
Stereo
English
Language
Speakers
Off
Optical Output Format
Dolby Digital
Reset
Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
To turn on the built-in speakers:
Select On in step 3 above.
46
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 47 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
When the correct PIN code is entered, the Locks menu opens.
Using the Locks menu
Locks
The Locks menu includes the Enable Rating Blocking, Edit
Rating Limits, Channels Block, Input Lock, Front (control)
Panel Lock, and New PIN Code features. You can use these
features after entering the correct PIN code.
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Off
Off
Off
Off
Front Panel Lock
Game Timer
New PIN Code
Entering the PIN code
Navigate
ENTER
MENU Back EXIT Exit
Select
1
Press Y and highlight the Locks menu icon.
If you cannot remember your PIN code
While the PIN code entering screen is displayed, press E four
times within five seconds. The PIN code will be cleared and
you can enter a new PIN code.
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Off
Off
Off
Off
Front Panel Lock
Game Timer
Changing your PIN code
New PIN Code
Navigate
ENTER
CH RTN Back
EXIT Exit
Select
1
2
3
4
Press Y and highlight the Locks menu icon.
Press b to display the PIN code entering screen.
Enter your four-digit PIN code and press T.
Press b to highlight New PIN Code and press T.
2
Press b, which displays the PIN code entry screen.
• The Lock System screen (below) appears if a PIN
code has not been stored. Press the Channel Number
buttons to enter a new four-digit code, enter the code a
second time to confirm, and press T.
Lock System
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Off
Please enter a 4 digit PIN code
Off
Off
Off
Front Panel Lock
Game Timer
Confirm PIN code
New PIN Code
Navigate
ENTER
MENU Back EXIT Exit
Select
Cancel
Done
5
6
Press the Number buttons to enter a new four-digit code.
Reenter the PIN code to confirm it.
• The Locks/Active screen (below) appears if the PIN
code is already stored. Use the Number buttons to enter
your four-digit code and press T.
Press T. The new PIN code is now active.
New PIN Code
Locks
Active
Please enter a 4 digit PIN code
Please enter the 4 digit PIN code
*
*
*
*
*
*
*
*
Confirm PIN code
*
*
*
*
Cancel
Done
Cancel
Done
If the wrong PIN code is entered, the message “Incorrect PIN
code, please try again!” appears. Highlight Retry and press
T. Enter the code again and press T.
47
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 48 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Blocking TV programs and movies
by rating (V-Chip)
Some TV programs and movies include signals that classify
the content of the program (violence, sex, dialog, language).
The V-Chip feature in this TV detects the signals and blocks
the programs according to the ratings you select. (For rating
descriptions, see the tables on the next page.)
Downloading an additional rating system
for blocking TV programs and movies
In the future, an additional rating system may become
available for use in selectively blocking programs.
Note: The currently tuned station must be receiving a digital
signal before an additional rating system can be downloaded.
To download the additional rating system
(if available):
Note: Rating blocking is a function of the V-Chip feature in this
TV, which supports the U.S. V-Chip system only.
To block and unblock TV programs and movies:
1
2
3
4
5
6
Press Y and highlight the Locks menu icon.
Press b to display the PIN code entering screen.
Enter your four-digit PIN code and press T.
Press b to highlight Enable Rating Blocking.
Press c and b to select On, and press T.
1
2
3
4
5
Press Y and highlight the Locks menu icon.
Press b to display the PIN code entering screen.
Enter your four-digit PIN code and press T.
Press b to highlight Enable Rating Blocking.
Press c and b to select On, and press T.
Press b to highlight Edit Rating Limits and press T.
The Edit Rating Limits screen appears.
7
Highlight Alt RS and press T. The Edit Alternate
Locks
Ratings screen will appear.
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Off
Off
On
Note:
Off
Off
Off
• The Alt RS button will only be available if an additional
rating system is currently available.
• It may take several minutes for the TV to download the
additional rating system.
Front Panel Lock
Game Timer
New PIN Code
Navigate
ENTER
MENU Back EXIT Exit
Select
• The information displayed in the Alternate Ratings
screen will depend on the configuration of the
additional rating system available at the time of
download.
6
7
Press b to highlight Edit Rating Limits and press T.
The Edit Rating Limits screen (below) appears.
Press BbC c and then press T to select the level of
blocking you prefer. A box with an “5” is a rating that will
be blocked. As you highlight a rating, a definition for the
rating appears at the bottom of the screen.
8
9
Press B b C c and then press T to select the level of
blocking you prefer. A box with an “5” is a rating that will
be blocked.
8
When you are finished selecting the ratings you want to
block, highlight Done and press T.
When you are finished selecting the ratings you want to
block, highlight Done and press T.
Edit Rating Limits
10 In the Edit Rating Limits screen, highlight Done and
Movies
G
TV (V-CHIP) FV
TV-Y
D
L
S
V
press T.
Children
Youth
TV-Y7
TV-G
PG
Note:
PG-13
R
TV-PG
TV-14
TV-MA
• The additional rating system can only be downloaded one
time. You will not be able to download any updates to the
rating system should such updates become available.
NC-17
X
Alt RS
Cancel
Done
"None" Rated
• The additional rating system is not designed, transmitted, or
controlled by the TV or Toshiba, nor is the availability of an
additional rating system determined or controlled by
Toshiba. Similarly, the rating of programs in an additional
rating system is not determined, transmitted, or controlled
by the TV or Toshiba.
• The additional rating system is an evolving technology;
therefore, availability, content, and format may vary.
48
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 49 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Blocking channels
With the Channels Block feature, you can block specific
channels. You will not be able to tune blocked channels unless
you unblock them.
Independent rating system for broadcasters
Ratings
Description and Content themes
Mature Audience Only (This program is specifically
designed to be viewed by adults and therefore may
be unsuitable for children under 17.)
L) Crude or indecent language S) Explicit sexual
activity V) Graphic violence
TV-MA
To block channels:
Parents Strongly Cautioned (This program contains
some material that many parents would find
unsuitable for children under 14 years of age.)
D) Intensely suggestive dialog L) Strong, coarse
language S) Intense sexual situations V) Intense
violence
1
2
3
4
Press Y and highlight the Locks menu icon.
Press b to display the PIN code entering screen.
Enter your four-digit PIN code and press T (-page 47).
Press b to highlight Channels Block and then press T.
TV-14
Parental Guidance Suggested (This program
contains material parents may find unsuitable for
younger children.)
D) Some suggestive dialog L) Infrequent coarse
language S) Some sexual situations V) Moderate
violence
Locks
TV-PG
TV-G
Enable Rating Blocking
Off
Edit Rating Limits
Channels Block
Input Lock
Off
Off
Front Panel Lock
Game Timer
General Audience (Most parents would find this
program suitable for all ages.)
Off
New PIN Code
Directed to Older Children (This program is designed
for children age 7 and above. Note: Programs in
which fantasy violence may be more intense or more
combative than other programs in this category are
designated TV-Y7FV.)
Navigate
ENTER
MENU Back EXIT Exit
Select
TV-Y7,
5
6
Press BbC c to select the input for which you want to
block channels (ANT1 or ANT2) and press T.
A list of the channels available for that input will be
displayed along with the call letters for each channel, if
available.
TV-Y7FV
All Children (This program is designed to be
appropriate for all children.)
TV-Y
Press Bb to highlight the channel you want to block and
press T, which puts an “5” in the box next to that
channel.
Independent rating system for movies
Ratings
X
Description and Content themes
X-rated (For adults only)
Channels Block
Not intended for anyone 17 and under
NC-17
1
2
ANT 1
ANT 2
Restricted (Under 17 requires accompanying parent
or adult)
R
3
4
Parents Strongly Cautioned (Some material may be
inappropriate for children under 13)
5
PG-13
6
7
Allow All
Block All
Cancel
Done
Parental Guidance Suggested (Some material may
not be suitable for children)
PG
G
8
9
General Audience (Appropriate for all ages)
10
Note:
7
8
Repeat step 6 for other channels you want to block.
• If you place an “5” in the box next to “‘None’ Rated,”
programs rated “None” will be blocked; however, programs
that do not provide any rating information will not be
blocked.
Highlight Done and press T.
To unblock individual channels:
In step 6 above, press Bb to highlight the channel you want to
unblock, press T to remove the “5” from the box, highlight
Done and press T.
• To display the rating of the program you are watching, press
E on the remote control. If it is rated “None,” the word
“NONE” appears in the RECALL screen (as shown below
right). If rating information is not provided, no rating will
appear in the RECALL screen.
To block all channels at once:
Highlight Block All in step 6 above, and then highlight Done
and press T.
TV –PG
L
V
NONE
(continued)
49
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 50 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
To unblock all blocked channels at once:
Highlight Allow All in step 6 on the previous page, and then
highlight Done and press T.
Using the input lock feature
You can use the Input Lock feature to lock the video inputs
(VIDEO 1, VIDEO 2, ColorStream HD-1, ColorStream
HD-2, HDMI 1, HDMI 2, and PC) and channels 3 and 4. You
will not be able to view the input sources or channels until you
unlock the inputs.
Channels Block
1
2
ANT 1
ANT 2
3
4
To lock/unlock the video inputs:
5
6
7
Allow All
Block All
Cancel
Done
1
2
3
4
Press Y and highlight the Locks menu icon.
Press b to display the PIN code entering screen.
Enter your four-digit PIN code and press T.
Press b to highlight Input Lock and press c.
8
9
10
Unlocking programs temporarily
If you try to tune the TV to a program that exceeds the rating
limits you set, the TV will enter program lock mode and the
following message will appear:
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Off
Off
Video
Video +
Off
Off
Off
This program exceeds the rating limit you set.
Push 'mute' to enter PIN.
Front Panel Lock
Game Timer
New PIN Code
You can either temporarily unlock the program or select an
unlocked program to watch.
Navigate
ENTER
MENU Back EXIT Exit
Select
5
Press B or b to select the desired level of video input
locking (Video, Video+, or Off, as described below),
and then press T.
Video: Locks VIDEO 1, VIDEO 2, ColorStream HD1/
HD2, HDMI 1/HDMI 2, and PC.
Video+: Locks VIDEO 1, VIDEO 2, ColorStream HD1/
HD2, HDMI 1/HDMI 2, PC and channels 3 and 4.
• Select Video+ if you play video tapes via an ANT input.
• When a CableCARD™ is inserted, Video+ will not lock
channels 3 and 4.
To temporarily unlock the program:
1
2
Press W.
Enter your four-digit PIN code and press T. If the correct
code is entered, the program lock mode is released and the
normal picture appears. All locking is disabled until the
TV is turned off, and will be enabled when the TV is
turned on again.
Locks
Active
Off: Unlocks all video inputs and channels 3 and 4.
Enter PIN code to temporaily un-block.
*
*
*
*
Cancel
Done
50
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 51 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Using the GameTimer™
You can use the GameTimer to set a time limit for playing a
video game (30–120 minutes). When the GameTimer is
activated, the TV enters Input Lock mode and locks out the
input source for the video game device.
Using the control panel lock feature
You can lock the control panel to prevent your settings from
being changed accidentally (by children, for example). When
the control panel lock is On, none of the controls on the TV
control panel will operate except POWER.
To set the GameTimer™:
To lock the control panel:
1
2
3
4
5
Press Y and highlight the Locks menu icon.
Press b to display the PIN code entering screen.
Enter your four-digit PIN code and press T.
Press b to highlight Game Timer and press c.
1
2
3
4
5
Press Y and highlight the Locks menu icon.
Press b to display the PIN code entering screen.
Enter your four-digit PIN code and press T.
Press b to highlight Front Panel Lock.
Press B or b to select the length of time until the Input
Lock is activated (30, 60, 90, or 120 minutes) and press
T.
Press c, and then B or b to highlight On and press T.
When the control panel is locked and any button on the
control panel (except POWER) is pressed, the message
“Not Available” appears.
Locks
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Off
Off
Locks
30 min
60 min
90 min
120 min
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Off
Off
On
Off
Off
Off
Front Panel Lock
Game Timer
Off
Off
Off
Front Panel Lock
Game Timer
New PIN Code
New PIN Code
Navigate
ENTER
MENU Back EXIT Exit
Select
Navigate
ENTER
MENU Back EXIT Exit
Select
To cancel the GameTimer™:
Select Off in step 5 above.
To unlock the control panel:
Highlight Off in step 5 above, or press and hold the
VOLUME – button on the TV control panel for about 10
seconds until the volume icon appears.
To deactivate the Input Lock once the GameTimer
has activated it:
Set the Input Lock to Off (- “Using the input lock feature”
on the previous page).
Note:
• A message will appear when 10 minutes, 3 minutes, and 1
minute remain on the GameTimer.
• If the TV loses power with time remaining on the GameTimer,
when power is restored the TV will enter Input Lock mode
(as if the GameTimer had been activated) and you will have
to deactivate the Input Lock (as described above).
51
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 52 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Setting the sleep timer
Setting the On/Off Timer
You can set the sleep timer to turn off the TV after a set length
of time (maximum of 180 minutes).
You can set the On/Off Timer to turn the TV on and off
automatically at a preset time on a recurring basis.
Note: You must first set the time (- page 28).
To set the sleep timer using the remote control:
Press [ on the remote control to set the length of time until
the TV turns off. Repeatedly press [ to increase the time in
10-minute increments, or press B or b to increase or decrease
the time in 10-minute increments, to a maximum of 180
minutes.
To set the On/Off Timer:
1
2
3
Press Y and open the Setup menu.
Highlight On/Off Timer and press T.
In the DAY field, press C or c to select the recurrence
(weekends, weekdays, every day, etc).
To set the sleep timer using the menus:
On/Off Timer
1
2
Press Y and open the Setup menu.
Highlight Sleep Timer and press T.
Turn TV ON:
Day
Weekends
AM
30 Minutes
0
9
:
0
0
Time (HH:MM)
TV ON Duration:
Reset
Cancel
Done
Setup
Installation
4
Press b to highlight the Time field, and then use the
Number buttons to enter the time you want the TV to turn
on automatically.
Sleep Timer
On/Off Timer
PC Settings
ColorStream HD1 Audio
HDMI 1 Audio
No
Auto
No
ColorStream HD2 Audio
5
6
When the AM/PM field is highlighted, press c to select
AM or PM.
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
Press b to highlight the TV ON Duration field, and then
press C or c to select the length of time until the TV turns
off (30 Minutes, 1 Hour, 2 Hours, 4 Hours,
8 Hours, or 12 Hours).
3
4
Press the Number buttons to enter the length of time
in 10-minute increments.
Sleep Timer
Enter total minutes until the TV
turns off automatically (Maximum
180 minutes)
7
8
Highlight Done and press T.
Turn off the TV. The TV will turn on automatically on the
day(s) and at the time you set. The TV will then turn off
automatically after the length of time you set in the
TV ON Duration field.
1 2 0
Cancel
Done
Highlight Done and press T.
Note:
Note:
• When a power failure occurs, the On/Off Timer settings
may be cleared.
• To display the On/Off Timer setting, press E.
• When a power failure occurs, the sleep timer setting
may be cleared.
• A message will display when there is one minute
remaining on the sleep timer.
To turn off the On/Off Timer:
Select Not Set in step 3 above.
To display the remaining sleep time:
Press [.
On/Off Timer
Turn TV ON:
Day
Not Set
Sleep Timer
120 Minutes
Reset
Cancel
Done
Note: You also can view the remaining sleep time by pressing
E.
To cancel the sleep timer:
Repeatedly press [ until it is set to 0 minutes.
52
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 53 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
• Horizontal Position:
Using the PC settings feature
Moves the picture left/right.
The adjustment range is within 5 from center.*
You can view the image from a PC on the TV screen. The PC
must be connected to the TV’s PC IN terminals
(- Installation Guide).
• Vertical Position:
Moves the picture up/down.
The adjustment range is within 5 from center.*
The PC Settings feature allows you to make any necessary
adjustments to the image.
If the edges of the image are not visible, you can adjust the
Horizontal Position/Width and Vertical Position/
Height.
• Horizontal Width:
Adjusts the width of the picture.
The adjustment range is within 5 from center.*
• Vertical Height:
Adjusts the height of the picture.
The adjustment range is within 5 from center.*
If the picture is affected by interference, you can adjust the
Clock Phase and Sampling Clock.
• Clock Phase:
Helps to reduce noise and sharpen the picture.
The adjustment range is within 2 from center.*
To adjust the PC settings:
• Sampling Clock:
Helps to redure noise and minimize periodic vertical stripes
on the screen.
1
Repeatedly press + to select PC input mode
(- “Selecting the video input source to view” page 32).
The adjustment range is within 15 from center.*
2
3
Press Y and open the Setup menu.
Highlight PC Settings and press T.
*
The range of adjustment may vary slightly.
Note: If a PC is not connected, this feature will be grayed
out in the Setup menu.
Setup
Installation
Sleep Timer
On/Off Timer
PC Settings
ColorStream HD1 Audio
HDMI 1 Audio
No
Auto
No
ColorStream HD2 Audio
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
4
5
Press B or b to highlight the item you want to adjust.
Press C or c to make the appropriate adjustments.
PC Settings
Horizontal Position
Horizontal Width
Vertical Position
Vertical Height
Clock Phase
0
0
0
0
0
0
Sampling Clock
Reset
Done
Note: The screen is disrupted momentarily when adjusting the
PC settings. This is not a sign of malfunction.
53
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 54 Tuesday, June 27, 2006 1:43 PM
Chapter 5: Using the TV’s features
Displaying TV status information
using RECALL
Understanding the auto power off
feature
The TV will automatically turn itself off after approximately
15 minutes if it is tuned to a vacant channel or a station that
completes its broadcast for the day. This feature functions in
ANT 1 and ANT 2 modes only.
To display TV status information:
Press E on the remote control.
The following information will display (if applicable):
• Current input (ANT 1, ANT 2, VIDEO 1, etc.)
• If ANT 1 or ANT 2 is the current input, either “CABLE”
(for cable TV) or “TV” (for over-the-air broadcasts).
• Channel number (if in ANT 1 or ANT 2 mode)
• Digital signal strength indicator (bar graph in lower right
corner of screen; for ATSC signal only)
Understanding the last mode
memory feature
If the power is cut off while you are viewing the TV, the
Last Mode Memory feature automatically turns on the TV
when the power is resupplied.
• Time (if set)
• On timer setting (if set)
• Remaining time on game timer (if set)
• Remaining time on sleep timer (if set)
• Stereo or SAP audio status
• V-Chip rating status
Note: You should unplug the TV’s power cord if it is possible
that you will be away from the TV for an extended period of time
after the power is restored. This will prevent the TV from turning
on automatically in your absence.
• Picture size
• Video resolution
• Lamp mode (appears only if the TV is in High Bright mode)
STEREO
NC-17
Sleep Timer: 18 min.
Game Timer: 28 min.
Lamp High Bright
Natural
ANT 1
480i
5:32 pm
CABLE 81-1
Sample RECALL screen
To close the RECALL screen:
Press E again.
54
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 55 Tuesday, June 27, 2006 1:43 PM
Chapter 6: Using the TV’s advanced features
Using CableClear® digital noise reduction
Using the advanced picture settings
features
The CableClear® digital noise reduction feature allows you to
reduce visible interference in your TV picture. This may be
useful when receiving a broadcast with a weak signal
(especially a Cable channel) or playing a noisy video cassette
or disc.
Using dynamic contrast
When dynamic contrast is set to Low, Middle or High, the
TV will detect changes in the picture quality that affect the
appearance of your contrast settings and then automatically
adjust the video.
To change the CableClear settings:
1
2
3
Press Y and open the Video menu.
Highlight Advanced Picture Settings and press T.
In the CableClear field, select your desired setting.
To select dynamic contrast preferences:
Advanced Picture Settings
ANT 1
1
2
Press Y and open the Video menu.
Highlight Advanced Picture Settings and press T.
Dynamic Contrast
CableClear
High
Auto
MPEG Noise Reduction
Color Temperature
Lamp Mode
Low
Cool
Low Power
Middle
Vertical Edge Enhancer
Color Management
Video
Picture Settings
Game Mode
Off
Advanced Picture Settings
Theater Settings
Reset
Done
Note:
• If the current input is ANT 1, ANT 2, VIDEO 1, or
VIDEO 2, the menu will display the text “CableClear.”
The available selections are Off, Low, Middle, High,
and Auto.
• If the current input is ColorStream HD1, ColorStream
HD2, or HDMI, the menu will display the text “DNR.” The
available selections are Off, Low, Middle, High, and
Auto. Auto will react proportionally to the strength of
the noise. Low, Middle, and High will reduce the noise
in varying degrees, from lowest to highest, respectively.
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
3
In the Dynamic Contrast field, select either Off, Low,
Middle or High.
\
Advanced Picture Settings
ANT 1
Dynamic Contrast
CableClear
High
Auto
MPEG Noise Reduction
Color Temperature
Lamp Mode
Low
Cool
Low Power
Middle
Vertical Edge Enhancer
Color Management
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Game Mode
Off
Reset
Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Note: If the current picture mode is Movie (in the Picture
Settings menu; - page 42), when the dynamic contrast
is set to Low, Middle, or High, the picture mode will
automatically change to Preference.
55
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 56 Tuesday, June 27, 2006 1:43 PM
Chapter 6: Using the TV’s advanced features
Using MPEG noise reduction
Selecting the color temperature
You can change the quality of the picture by selecting from
three preset color temperatures (cool, medium, and warm), as
described below.
The MPEG noise reduction feature allows you to reduce
visible interference caused by MPEG compression. Choices
for MPEG noise reduction are Off, Low, Middle, and High.
Off is automatically selected when this feature is disabled
(“grayed out”).
Mode
cool
Picture Quality
blueish
To select the MPEG noise reduction level:
medium
warm
neutral
1
2
3
Press Y and open the Video menu.
Highlight Advanced Picture Settings and press T.
Press B or b to highlight the MPEG Noise Reduction
field, and then press C or c to select either Off, Low,
Middle or High.
reddish
To select the color temperature:
1
2
3
Press Y and open the Video menu.
Highlight Advanced Picture Settings and press T.
In the Color Temperature field, select the mode you
prefer (Cool, Medium, or Warm).
Advanced Picture Settings
ANT 1
Dynamic Contrast
CableClear
High
Auto
MPEG Noise Reduction
Color Temperature
Lamp Mode
Low
Cool
Advanced Picture Settings
ANT 1
Low Power
Middle
Dynamic Contrast
CableClear
High
Auto
Vertical Edge Enhancer
Color Management
MPEG Noise Reduction
Color Temperature
Lamp Mode
Low
Game Mode
Off
Cool
Reset
Done
Low Power
Middle
Vertical Edge Enhancer
Color Management
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Game Mode
Off
Reset
Done
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Note: If you select one of the factory-set picture modes
(Sports, Standard, or Movie) and then change the color
temperature mode, the picture mode automatically
changes to Preference in the Picture Settings menu.
56
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 57 Tuesday, June 27, 2006 1:43 PM
Chapter 6: Using the TV’s advanced features
Selecting the lamp mode
Using the Vertical Edge Enhancer feature
The Vertical Edge Enhancer feature strengthens video contour.
You can select either the High Bright or Low Power lamp
mode.
To turn on the Vertical Edge Enhancer feature:
The High Bright mode is useful when additional picture
brightness is desired (such as in a bright room).
1
2
3
Press Y and open the Video menu.
Highlight Advanced Picture Settings and press T.
In the Vertical Edge Enhancer field, select the mode
you prefer (Off, Low, Middle, or High).
To select the lamp mode:
1
2
3
Press Y and open the Video menu.
Highlight Advanced Picture Settings and press T.
In the Lamp Mode field, select either High Bright or
Low Power.
Advanced Picture Settings
ANT 1
Dynamic Contrast
CableClear
High
Auto
MPEG Noise Reduction
Color Temperature
Lamp Mode
Low
Cool
Advanced Picture Settings
ANT 1
Low Power
Middle
Dynamic Contrast
CableClear
High
Auto
Vertical Edge Enhancer
Color Management
Game Mode
MPEG Noise Reduction
Color Temperature
Lamp Mode
Low
On
Cool
Reset
Done
Low Power
Middle
Vertical Edge Enhancer
Color Management
4
To save the new settings, highlight Done and press T.
Game Mode
Off
To revert to the factory defaults, highlight Reset and
Reset
Done
press T.
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Note:
• Changing the setting of this item will cause the Mode to
automatically change to Preference.
Note: If you set the lamp mode to Low Power, each time
you turn on the TV, the lamp will start out in High Bright
mode but will switch to Low Power mode after a short
period of time. You may notice a change in screen
brightness when this happens. This is normal and is not a
sign of malfunction.
• When the input is changed to PC, this feature is
automatically set to High and grayed out in the menu.
57
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 58 Tuesday, June 27, 2006 1:43 PM
Chapter 6: Using the TV’s advanced features
Using the Color Management feature
The Color management feature allows you to adjust the hue,
saturation, and brightness of six colors: red, green, blue,
yellow, magenta, and cyan.
Using the Game Mode feature
You can use the Game Mode feature for shorter frame delays
when playing a video game requiring split-second timing
between the on-screen display and input from the controller
(such as music creation and high-action games).
To adjust the Color Management settings:
Note: To use the Game Mode feature, the current video input
must be Video 1, Video 2, ColorStream HD1,
ColorStream HD2, HDMI 1 or HDMI 2. The Game Mode
cannot be turned on when any other video input is selected.
1
2
3
Press Y and open the Video menu.
Highlight Advanced Picture Settings and press T.
Highlight Color Management and press T.
To turn on Game Mode:
Advanced Picture Settings
ANT 1
Dynamic Contrast
CableClear
High
Auto
1
2
3
Press Y and open the Video menu.
Highlight Advanced Picture Settings and press T.
Press Bor bto highlight the Game Mode field, and then
press C or c to select On.
MPEG Noise Reduction
Color Temperature
Lamp Mode
Low
Cool
Low Power
Middle
Vertical Edge Enhancer
Color Management
Game Mode
Off
Advanced Picture Settings
Video 1
Reset
Done
Dynamic Contrast
CableClear
High
Auto
4
In the Color Management field, select On.
MPEG Noise Reduction
Color Temperature
Lamp Mode
Low
Cool
Color Management
Color Management
ANT 1
Low Power
Middle
Vertical Edge Enhancer
Color Management
Game Mode
On
Hue
–15
Saturation Brightness
On
Red
+15
0
0
0
0
0
0
Reset
Done
Green
Blue
0
–15
0
0
+15
0
Yellow
Magenta
Cyan
To turn off Game Mode:
Select Off in step 3 above, change the video input, or turn the
TV off and then on again.
–15
0
+15
0
Reset
Done
You can change the video input in any of the following ways:
• Pressing + on the remote control (- page 32).
• Changing the channel using the Numbers or < / ,, R,
3 C, # c.
5
6
Press Bor bto highlight the color you want to adjust, and
then press T.
Press B or b to select either Hue, Saturation, or
Brightness, and then press C and c to adjust the setting.
Hue
+2
+2
+2
Saturation
Brightness
7
8
Press T to return to the Color Management window.
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Note: If you select one of the factory-set picture modes
(Sports, Standard, or Movie) and then set Color Management
to On, the picture mode automatically changes to Preference
in the Picture Settings menu.
58
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 59 Tuesday, June 27, 2006 1:43 PM
Chapter 6: Using the TV’s advanced features
Using the virtual surround sound feature
(Dolby® Virtual/SRS TruSurround™)
The Dolby Virtual/SRS TruSurround feature allows you to
enjoy virtual surround sound from the TV's speakers.
Using the advanced audio settings
features
Using the SRS WOW™ surround sound
feature
To turn on the Dolby Virtual/SRS TruSurround
feature:
SRS WOW™ is a special combination of SRS Labs audio
technologies (SRS 3D, SRS Focus, and SRS TruBass) that
creates a thrilling surround sound experience with deep, rich
bass from stereo sound sources. Your TV’s audio will sound
fuller, richer, and wider.
1
2
3
Press Y and open the Audio menu.
Highlight Advanced Audio Settings and press T.
In the Dolby Virtual/SRS TruSurround field, select
On.
Advanced Audio Settings
To adjust the WOW™ settings:
WOW: SRS 3D
Off
Off
WOW: SRS Focus
WOW: SRS TruBass
High
1
Put the TV in STEREO mode (-“Selecting stereo/SAP
broadcasts” on page 45).
Dolby Virtual
On
SRS TruSurround
Reset
Done
2
3
4
Press Y and open the Audio menu.
Highlight Advanced Audio Settings and press T.
Press b or B to highlight the WOW feature you want to
adjust, and then press C or c to adjust the item.
4
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
Advanced Audio Settings
To turn off the Dolby Virtual/SRS TruSurround
feature:
Select Off in step 3 above.
WOW: SRS 3D
Off
Off
WOW: SRS Focus
WOW: SRS TruBass
High
Dolby Virtual
On
SRS TruSurround
Note: The Dolby Virtual/SRS TruSurround and WOW SRS
3D features cannot be on at the same time. If you set one to
On, the other will automatically be set to Off.
Reset
Done
• WOW: SRS 3D — To turn the surround sound effect
On or Off.
Note: If the broadcast is monaural, the SRS 3D effect
will not work.
• WOW: SRS Focus — To turn the vocal emphasis effect
On or Off.
• WOW: SRS TruBass — To select the desired bass
expansion level (Off, Low, or High).
5
To save the new settings, highlight Done and press T.
To revert to the factory defaults, highlight Reset and
press T.
WOW, TruSurround, SRS and l symbol are trademarks of SRS Labs,
Inc.
WOW and TruSurround technologies are incorporated under license
from SRS Labs, Inc.
59
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 60 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
The Toshiba Home Interactive Network Connection
(THINC™) feature allows you to connect the TV to your home
network, which will enable access to file sharing and
e-mail scheduling features.
For home network troubleshooting tips, see Chapter 8.
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the United States and
other countries, and may subject you to civil and criminal
liability.
File sharing
You can access JPEG and MP3 files that are stored on your
networked home PC and view/play them on the TV.
Note: Requires a home network* (- Installation Guide).
Does NOT require Internet/e-mail service.
B. Setting up the network address
E-mail scheduling of recordings and reminders
You can schedule recordings and reminders by sending an e-
mail to the TV from any PC.
To set up the network address:
1
2
First, try automatically setting up the network address
(below).
Note:
• Requires a compatible recording device (- Installation
Guide); a home network* (- Installation Guide); and home
Internet service with a dedicated POP3 e-mail address for
the TV (different from your personal e-mail address).
If the automatic setup is not successful, you can either
retry the automatic setup (below) or try manually setting
up the network address (- page 61).
Note:
•
Contact your Internet Service Provider (ISP) to obtain
and set up Internet/e-mail service.
• If you used an Ethernet crossover cable to connect your PC
directly to the TV, you will not be able to use the automatic
setup, and must manually set up the network address.
• If you used a hub or switch to connect the TV to your home
network, you will not be able to use the automatic setup, and
must manually set up the network address.
•
You will NOT be able to access or browse the Internet
through the TV.
Follow the steps in sections A through D (- pages 60–65)
to set up and use the TV’s home network features.
* The THINC™ home network feature is compatible only with
Microsoft® Windows® 2000 and the Home and Professional
versions of Microsoft® Windows® XP Service Pack 1 and
Service Pack 2.
Microsoft and Windows are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or
other countries.
• If you used a router with built-in DHCP functionality, use the
automatic setup. Manual setup may not work.
Router technology, like all new and emerging technology,
may from time to time cause compatibility issues because of
the differences in router systems implemented by the various
router manufacturers; however, most issues can be easily
resolved. If you think your Toshiba TV and router might have
compatibility problems, please contact the following:
• In the U.S., call TACP Consumer Solutions at
A. Connecting the TV to your home
network
customersupport/contact.asp
.
• In Canada, call TCL Customer Service at
1
Connect the TV to your home network via the TV’s
RJ-45 (Ethernet) port. See the Installation Guide for
connection instructions.
Automatically setting up the network
address
2
If you want to use file sharing only and do not have
Internet service in your home:
Go to section B, “Setting up the network address,”
at right.
1
2
Press Y and open the Setup menu.
Highlight Installation and press T. The Installation
Note: If you do not have Internet service, you will not be
able to use the e-mail scheduling feature.
menu appears.
3
Open the Network menu.
If you want to use file sharing and e-mail scheduling:
a) You must have Internet service in your home and a
dedicated e-mail address for the TV (different from
your personal e-mail address). Contact your ISP to
obtain and set up Internet/e-mail service in your home.
b) After you have obtained Internet/e-mail service in your
home (from your ISP), go to section B, “Setting up the
network address” at right.
60
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 61 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
4
Highlight Basic Network Setup and press T.
d) Retry the automatic network address setup by following
these steps:
(1) Highlight OK and press T.
(2) Repeat steps 1–6. (If you have already repeated
this setup process, go to step 9.)
Network
Basic Network Setup
E-mail Scheduling Setup
Home File Server Setup
Software Upgrade
9
If, after repeating steps 1–6, you receive the error
message shown in step 8:
Either…
Navigate
ENTER
CH RTN
Back
EXIT Exit
a) Highlight “OK” and press T.
b) Go to “Manually setting up the network address.”
Select
5
6
The message “Obtain network address automatically?”
will display. Highlight Yes and press T.
Or…
a) Highlight “OK” and press T.
Basic Network Setup
b) Continue to sections C, D, and E (- pages 62–69)
(to set up and use file sharing) and/or to sections F and
G (- pages 70–78) (to set up and use e-mail
scheduling).
If the file sharing and/or e-mail scheduling features
work correctly, then the automatic network address
setup was successful (even though the TV displayed the
error message).
Obtain network address automatically?
Yes
No
The message “Please wait…” will display while the TV is
attempting to load the network address information from
the DHCP server.
Basic Network Setup
Please wait...
Manually setting up the network address
This setup requires the data listed below. You can get this
data from either your ISP or the configuration utility for
your DSL/cable modem or router.
If the automatic network address setup is successful,
go to step 7.
If the automatic network address setup is not
successful, go to step 8.
IP address:
___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___
Subnet mask:
7
8
If the automatic network address setup is successful, the
following screen will appear:
___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___
Gateway (Router) address:
___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___
DNS (Domain Name Server) address:
___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___
Basic Network Setup
Done! Network address information has been found!
Exit
a) Press T to close the screen and return to the Network
1
2
Press Y and open the Setup menu.
menu.
b) Skip to section C, “Setting up file sharing on your PC”
(- page 62).
Highlight Installation and press T. The Installation
menu appears.
If the automatic network address setup is not successful,
the following screen will appear:
3
4
5
Open the Network menu.
Highlight Basic Network Setup and press T.
The message “Obtain network address automatically?”
appears.
Highlight No and press T.
Basic Network Setup
a) Make sure all cables for your home network are
securely connected.
Obtain network address automatically?
Yes
No
b) Make sure your home network is set up properly. See
the Installation Guide for TV connection
information. Also consult the owner’s manuals for
your other components.
c) Make sure the DHCP and security settings on your
home router are correct. Consult the owner’s manual
for your router.
(continued)
61
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 62 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
6
The Basic Network Setup menu appears.
C. Setting up file sharing on your PC
Press B or b to highlight the IP Address field, and then
use the Number buttons on the remote control to input the
IP address.
Compatible operating systems
Basic Network Setup
Please enter your Network Address Information
The following operating systems are compatible for file
sharing with the TV:
• Microsoft® Windows® XP Service Pack 2
0
0
0
0
0
0
0
IP Address
Subnet Mask
225 225 225
Gateway (Router)
0
0
0
0
0
0
DNS (Domain Name Saver)
Cancel
Done
(Home Edition and Professional) [See setup details below]
• Microsoft® Windows® XP Service Pack 1
(Home Edition and Professional) [See setup details below]
• Microsoft® Windows® 2000 [See setup details on page 64]
No other operating systems are compatible with the TV.
7
8
Press bto highlight the Subnet Mask field, and then use
the Number buttons to input the Subnet Mask.
Press b to highlight the Gateway (Router) field, and
then use the Number buttons to input the Gateway
(Router) address.
Note:
• The name of any directory/folder on your PC that you are
setting up for file sharing with the TV cannot be longer than
12 characters and cannot contain any special characters.
• See “Media specifications” (- page 66) for details on
compatible JPEG and MP3 files.
9
Press b to highlight the DNS (Domain Name Server)
field, and then use the Number buttons to input the DNS
address.
10 When finished, highlight Done and press T.
The Basic Network Setup menu closes and the
Network menu appears.
• The network (NETBIOS) name of your PC that you are setting
up for file sharing must be 15 characters or less.
11 Go to section C, “Setting up file sharing on your PC.”
To determine which operating system and service
pack (if applicable) are on your PC:
Resetting the network address
1
2
3
4
On your PC, click the “Start” button.
Click “Settings | Control Panel.”
1
2
Press Y and open the Setup menu.
Highlight Installation and press T. The Installation
In the Control Panel, double-click “System.”
menu appears.
Select the “General” tab, which will display your PC’s
current operating system and service pack.
3
4
5
Open the Network menu.
Highlight Basic Network Setup and press T.
The message “Your Basic Network Setup is complete.
Would you like to start over?” will appear.
Setting up file sharing on a PC with
Microsoft® Windows® XP Service Pack 1 or
Service Pack 2
To continue, highlight Yes and press T.
To return to the Network menu, highlight No and
press T.
1
On your PC:
Basic Network Setup
Your Basic Network Setup is complete. Would you like to start over?
Yes
No
a) Right-click
the folder
to be shared.
6
If you selected Yes in step 5, the message “Obtain
network address automatically?” will appear.
Basic Network Setup
Obtain network address automatically?
b)Click “Sharing
and Security...”
(which will open
the Properties
window for the
selected folder.)
Yes
No
To obtain the network address automatically, go to step 5
under “Automatically setting up the network address”
(- page 60).
To manually enter the network address, go to “Manually
setting up the network address.”
For home network troubleshooting tips, see Chapter 8.
* Microsoft product screen shot(s) reprinted with permission from
Microsoft Corporation.
62
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 63 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
2
If the “Sharing” tab on your PC does not have a
3
In the Permissions window for the selected folder:
“Permissions” button, follow step 2.1 below.
If the “Sharing” tab on your PC has a “Permissions”
button, follow step 2.2 below.
a) Click “Add...”
and then select the
user to be given
sharing privileges.*
2.1
*This user must match
the user stored in the
TV’s “Home File Server
Setup” menu.
a) Click to display
the “Sharing” tab.
b)Click to check
“Allow” next to
“Full Control.”
b)Click to select
“Share this folder
on the network.”
c) Click “Apply.”
d)Click “OK”
to close the window.
c) Click “OK”
(which will close the
Permissions window
for the selected folder).
4
Go to section D, “Setting up file sharing on the TV,” on
page 65.
Go to section D, “Setting up file sharing on the TV,” on
page 65.
2.2
a) Click to display
the “Sharing” tab.
b)Click to select
“Share this folder.”
c) Click “Permissions”
(which will open
the Permissions
window for the
selected folder).
Go to step 3.
63
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 64 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
4
In the Properties window:
Setting up file sharing on a PC with
Microsoft® Windows® 2000
1
On your PC:
a) Right-click
the folder
to be shared.
Click “OK”
(which closes
the Properties
window).
b)Click “Sharing...”
(which will open
the Properties
window for the
selected folder).
5
The shared folder will display with a “shared folder” icon
(a hand holding a folder).
2
In the Properties window for the selected folder:
a) Click to display
the “Sharing” tab.
b)Click to select
“Share this folder.”
c) Click “Permissions”
(which will open
the Permissions
window for the
selected folder).
6
Go to section D, “Setting up file sharing on the TV,” on
the next page.
3
In the Permissions window for the selected folder:
For home network troubleshooting tips, see Chapter 8.
a) Click “Add...”
and then select the
user to be given
sharing privileges.*
*This user must match
the user stored in the
TV’s “Home File Server
Setup” menu.
b)Click to check
“Allow” next to
“Full Control.”
c) Click “Apply.”
d)Click “OK”
(which closes the
Permissions window).
64
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 65 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
7
Press Bb to highlight either JPEG Picture Directory
D. Setting up file sharing on the TV
or MP3 Music Directory.
Note: The first time you highlight either of these fields, the
message “Please Wait...” will appear until the field is
populated with the files in your PC’s shared folder(s).
1
2
Press Y and open the Setup menu.
Highlight Installation and press T. The Installation
Home File Server Setup
Please Wait...
menu will appear.
Please enter your Home Server Setup Information.
Home Server Name
ABCD
XYZ
Open the Network menu.
User Name
Password
*******
JPEG Picture Directory
MP3 Music Directory
Software Upgrade Directory
--
--
--
Network
Basic Network Setup
E-mail Scheduling Setup
Home File Server Setup
Software Upgrade
Cancel
Done
8
9
Press C c to select the shared folder (on your PC) that
contains the JPEG and/or MP3 files you want to view/play
on the TV.
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
Note: Make sure you select the correct folder in this step.
3
Highlight Home File Server Setup and press T. The
To exit the window and save your settings, highlight
Done and press T.
To exit the window without saving your settings, highlight
Home File Server Setup window will appear.
After a few moments, the message “Please Wait...” will
appear until the network finds your networked PC.
The networked PC will act as the “Home Server” for file
sharing with the TV.
Cancel and press T.
USING THE ON-SCREEN KEYBOARD
Home File Server Setup
Please enter your Home Server Setup Information.
ABCD
XYZ
Home Server Name
User Name
a) Press BbC c to highlight the desired letter, number,
or character, and then press T.
Password
*******
JPEG
JPEG Picture Directory
MP3 Music Directory
Software Upgrade Directory
MP3
--
XXXX@XXXXX.XX_
1
q
2
3
e
4
r
5
t
6
y
7
u
8
i
9
o
0
p
-
[
=
]
Cancel
Done
w
a
s
d
f
g
h
j
k
l
;
'
z
x
c
v
b
n
m
,
.
/
4
Press Bb to highlight Home Server Name, and then
press C c to select the name of the PC you set up for file
sharing.
Shift
Done
BS
Cancel
Clear
b) Repeat step “a” until you have finished entering all
characters for the selected field.
If you have multiple PCs on your home network that have
shared folders, press Ccto select the PC (home server) to
access files from.
Note:
• To toggle between uppercase and lowercase
letters and between numbers and symbols,
highlight Shift and press T.
Home File Server Setup
Please enter your Home Server Setup Information.
ABCD
Home Server Name
User Name
XYZ
Password
*******
JPEG
• To erase the last entered character, highlight BS
(backspace) and press T.
JPEG Picture Directory
MP3 Music Directory
Software Upgrade Directory
MP3
--
• To clear your entered characters, highlight Clear
and press T.
Cancel
Done
c) When you are finished entering all characters for the
selected field, highlight Done and press T.
You will return to the previous Setup window.
5
6
a. Press Bb to highlight User Name and then press T
to open the on-screen keyboard for that field.
b. Enter the User Name for your PC using the on-screen
keyboard. See “Using the on-screen keyboard,” at right.
About the Software Upgrade feature
Note: The User Name is case sensitive.
This feature allows you to download software updates to your
television from a shared folder on your home network.
If you experience any difficulties that can only be resolved by
a software update, your Toshiba customer service
c. When finished entering all characters, highlight Done
and press T.
Repeat step 5 for the Password field.
representative will provide you with the appropriate upgrade
files and assist you in the proper use of this feature.
Note: The Password is case sensitive.
65
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 66 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
Picture Viewer/JPEG file specifications
– Maximum JPEG file size: 8 MB
• JPEG files larger than 8 MB will not display.
– Maximum JPEG image resolution: 6000 5 4000 pixels
E. Viewing/playing shared files on
the TV
• Images with a resolution higher than 6000 5 4000 pixels
will not display.
You can use the Picture Viewer to view compatible JPEG-
format photos on the TV.
– The Picture Viewer is designed to display only pictures
stored in compatible JPEG formats with a file extension of
“.jpg.”
– JPEG images processed and/or edited on a personal
computer (PC) may not display properly or at all.
You can use the Audio Player to play compatible MP3 files
on the TV.
The TV can access JPEG and/or MP3 files stored on a
networked PC (as described on pages 67–69 in this Guide and
also in the Installation Guide).
– Some digital cameras may store images in a format that is
not compatible with the TV.
– JPEG files stored on a networked PC that are not in a file
and folder format compatible with the TV will not
display on the TV.
Note:
• If you are viewing/playing files stored on a networked PC,
IT IS RECOMMENDED THAT YOU BACK UP YOUR DATA.
Toshiba is not liable for any damage caused by the use of
any networked PCs or shared files with this TV. Toshiba will
not compensate for any lost data or recording(s) caused by
the use of such PCs or data.
Audio Player/MP3 file specifications
– Maximum MP3 file size: 50 MB
• MP3 files larger than 50 MB will not play.
– The Audio Player is designed to play only music files
stored in compatible MP3 formats with a file extension of
“.mp3.”
• The technical criteria set out in this Guide are meant as a
guide only.
•
You must obtain any required permission from
copyright owners to download or use copyrighted
content. Toshiba cannot and does not grant such
permission.
– MP3 files processed and/or edited on a PC may not play
properly or at all. Some MP3 files may be in a format that is
not compatible with the TV.
– MP3 files must be in the following format:
• MPEG1 (ISO/IEC 11172-3) Layer3.
Media specifications
File/folder name specifications
– Maximum file name length: 255 characters.
– Maximum shared folder* name length: 12 characters.
– File names must contain US-ASCII characters only.
• Sampling frequency—MPEG1: 32 kHz, 44.1 kHz,
48 kHz.
• Bitrate—MPEG1: 32–320 kbps.
• Channels—Stereo, Joint stereo, Dual channel, Single
channel.
– File and folder names cannot contain any special
characters, such as \ / : ? “ ” < > | .
• ID3 Ver. 1, Ver. 2.
– The meta-data for MP3 files (artist name, album name,
* The words “folder” and “directory” are used interchangeably.
song title, etc.) must be in the following format:
ISO-8859-1 (US-ASCII/ Western European) character
sets
– MP3 files stored on a networked PC that are not in a file
and folder format compatible with the TV will not play
on the TV.
66
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 67 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
Networked PC specifications
Using the Picture Viewer
You can use the TV’s Picture Viewer to display your digital
photos (JPEG files) on your TV’s screen in thumbnail mode or
as a slide show.
Maximum number of files per shared folder:
– JPEG = 1,000
• All JPEG files over the 1,000th in a shared folder will not
display.
Note:
• You cannot use the Picture Viewer and Audio Player at the
same time.
• You must obtain any required permission from
copyright owners to download or use copyrighted
content. Toshiba cannot and does not grant such
permission.
– MP3 = 200
• All MP3 files over the 200th in a shared folder will not play.
Maximum number of nested folder levels: 10 levels
• Files in folders more than 10 levels down from the top level
folder will not display/play.
• See pages 60–65 for details on networking your TV and PC
for file sharing.
Accessing JPEG files stored on a networked PC
1
Make sure you have correctly set up your home network
and file sharing (- pages 60–65 in this Guide; also see
the Installation Guide).
2
3
Press Y and open the Applications menu.
Highlight Picture Viewer and press T.
Applications
Picture Viewer
Audio Player
Channel Browser
TV Guide On Screen
Digital CC/Audio Selector
CableCARD
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
If the network is available, it will retrieve the JPEG
picture list via the network.
4
Press Bor bto access the folder or directory that contains
the JPEG pictures you want to view.
Picture Viewer
//BEARD-DESK/C
C
+
+
+
Copy of isi mip
QAWG_A
INCD
+
+
siImip
WINNT
+
Documents and Settings
CH RTN Image Select
ENTER Select
EXIT Exit
Navigate
To expand a particular folder to view a list of images,
press c on the folder.
To close the folder or directory, press C on the folder.
Pressing C on a file will move the focus up to the folder
that contains the file.
Pressing c on a file will move the focus down to the next
folder.
If you press T on a particular folder, the first file in the
folder will be displayed as the first file in the thumbnail
list.
If you press T on a particular file, that file will be
displayed as the first file in the thumbnail list.
Note: You can use R to toggle between the thumbnail
and folder views. The last item selected will be highlighted
upon return to the Picture Viewer.
(continued)
67
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 68 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
To set the slide show interval:
Viewing JPEG files on the TV
1
2
3
4
Press O to close the Picture Viewer (if it is open).
Press Y and open the Setup menu.
Highlight Slide Show Interval and press T.
Select the interval from the menu sidebar (2, 5, 10, 15, or
20 seconds).
1
After accessing your JPEG files from your networked PC
(-page 67), the images automatically display on-screen,
with one as a large picture and six in thumbnail format.
Picture Viewer
//ALLENMPC/Pics/Directory3/Subdirectory1/shelby concept.jpg.
1
of
8
Nov
2
05
2
of
8
Jun 25 01
3
of
8
Feb 10 05
4
of
8
Feb
8
05
5
of
8
Jun 25 01
Setup
6
of
8
Feb 10 05
PC Settings
2 Sec
CH RTN File Select
ENTER Slide Show
CH Page Up/Down EXIT Exit
Rotate
Next
ColorStream HD1 Audio
HDMI 1 Audio
No
Auto
No
5 Sec
10 Sec
15 Sec
20 Sec
2
3
Press C to rotate the large picture 90° counterclockwise.
ColorStream HD2 Audio
HDMI 2 Audio
Auto
2 Sec
On
Picture Viewer
//ALLENMPC/Pics/Directory3/Subdirectory1/shelby concept.jpg.
Slide Show Interval
Quick Restart
1
of
8
Nov
2
05
2
of
8
Jun 25 01
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
3
of
8
Feb 10 05
4
of
8
Feb
8
05
5
of
8
To view your JPEG files in Native Resolution mode:
Jun 25 01
6
of
8
Feb 10 05
Press < or , during the slideshow. This will expand the
CH RTN File Select
ENTER Slide Show
CH Page Up/Down EXIT Exit
Rotate
Next
image to its non-compressed format.
Press c to rotate the large picture 90° clockwise.
Press E to display a help bar that will show how to scroll to
the edges of the image using the B b C c buttons.
To exit Native Resolution and return to the normal slideshow,
press T.
Picture Viewer
//ALLENMPC/Pics/Directory3/Subdirectory1/shelby concept.jpg.
1
of
8
Nov
2
05
2
of
8
Jun 25 01
3
of
8
Feb 10 05
To return to thumbnail view, press either O or R.
If an image is too large to display in Native Resolution mode
(6MB), a warning message will display.
4
of
8
Feb
8
05
5
of
8
Jun 25 01
6
of
8
Feb 10 05
CH RTN File Select
ENTER Slide Show
CH Page Up/Down EXIT Exit
Rotate
Next
To close the Picture Viewer:
4
5
Press B or b to select another picture as the large picture.
Press O to close the Picture Viewer and return to the
Press T to view your pictures in a slide show.
regular TV screen.
During the slide show:
• To stop on an image during the slide show, press T.
• To resume the slide show, press T again.
• To rotate the picture, press C or c.
• To select another image, press B or b.
• To stop the slide show and return to the picture viewer, press
R.
• To stop the slide show and return to the regular TV screen,
press O.
68
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 69 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
If you press T on a particular folder, the first file in the
Using the Audio Player
folder will display as the first file in the list in song select
view.
You can use the TV’s Audio Player to listen to MP3 files on
the TV.
If you press T on a particular file, that file will display as
the first file in the list in song select view.
Note:
• Make all desired adjustments to the TV’s audio features
(e.g., surround, bass, treble, balance) before starting the
Audio Player.
• You cannot use the Picture Viewer and Audio Player at the
same time.
Note: You can use R to toggle between the thumbnail
and folder. The last item selected will be highlighted upon
return to the Audio Player.
Audio Player
//ALLENMPC/MP3's/Dir1/Sub1/03-Moonlight Sonata.mp3
Title
Artist
SCO/Sir Charles...
•
You must obtain any required permission from
copyright owners to download or use copyrighted
content. Toshiba cannot and does not grant such
permission.
Ser No.1 in D, Op.11...
VOL
Requiem, Op. 5: IV. R... Robert Shaw/Atla...
Rapsodie Espagnole:... Jesus Lopez-Cobo...
Moolight Sonata, movement
A-M Classical
III. Sanctus: Sanctu...
Boston Baroque/M...
Piano Sonata, K. 545... A-M Classical
Pathétique Sonata, m... A-M Classical
Chopin Prelude No. ...
Piano Sonata, K. 545...
Andrys
A-M Classical
A-M Classical
Playing MP3 files stored on a networked PC
Moolight Sonata, mo...
1
Make sure you have correctly set up your home network
and file sharing (- pages 60–65 in this Guide; also see
the Installation Guide).
CH RTN File Select
ENTER Select
EXIT Exit
Navigate
5
The Audio Player will begin playing the first MP3 file
in the list. Press BbC c to navigate to the rewind, pause,
fast forward, skip backward, skip forward, volume, and
mute buttons—or to select another MP3 file—and then
press T.
2
3
Press Y and open the Applications menu.
Highlight Audio Player and press T.
To adjust or mute the volume:
Applications
Picture Viewer
Audio Player
Press z Z or W on the remote control (see page 44 for
details on muting the sound), or press Bb C c to navigate to
the on-screen VOL and MUTE ( ) buttons and press T.
Channel Browser
TV Guide On Screen
Digital CC/Audio Selector
CableCARD
To close the Audio Player:
Navigate
ENTER
CH RTN
Back
EXIT Exit
Select
Press O to close the Audio Player and return to the regular
TV screen.
If the network is available, the TV will retrieve the MP3
file through the network.
4
Press Bor bto access the folder or directory that contains
the MP3 files you want to play.
Audio Player
//ALLENMPC/MP3's/Dir1/Queen pain Is Close to Pleasure.mp3
-
,
MP3
s
VOL
-
Dir
1
-
Sub
1
03
04
05
-
-
-
Take Five.mp3
Lá Breá Fán Dtuath.mp3
An Tûll.mp3
+
Sub
2
+
Dir
2
Queen
Queen
Queen
Queen
Queen
-
-
-
-
-
A
Kinnd of Magic.mp3
Forever.mp3
Gimme the Prize.mp3
One Vision.mp3
Pain is So Close to Pleasure.mp3
Simon and Garfunkel Cecilial.mp3
-
CH RTN Song Select
ENTER Select
EXIT Exit
Navigate
To expand a particular folder to view a list of images,
press c on the folder.
To close the folder, press C on the folder.
Pressing C on a file will move the focus up to the folder
which contains the file.
Pressing c on a file will move the focus down to the next
folder.
69
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 70 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
Setting up e-mail scheduling
F. Setting up e-mail scheduling
1
2
Press Y and open the Setup menu.
You can remotely schedule and delete recordings and
reminders by sending an e-mail to the TV from any PC.
Highlight Installation and press T. The Installation
menu appears.
Note:
3
4
Open the Network menu.
• If you have not already done so, follow the instructions in
sections A and B (- page 60), before proceeding.
• Before you can schedule recordings, the time and date in
the TV Guide On Screen feature must be set (- “Setting the
time and date” on page 28).
Highlight E-mail Scheduling Setup and press T. The
E-mail Scheduling Setup window opens.
E-mail Scheduling Setup
Please enter your E-mail Setup Information.
E-mail Scheduling
ID Required
On
On
ID
XXXXXXXXXXXXXXXX
Required information and services
Before you can set up the e-mail scheduling feature, you must
have the following information and related services:
E-mail Address
Account
Password
Incoming Mail Server
Outgoing Mail Server
E-mail Authorization
Authorized E-mail
On
a) A valid POP3 e-mail address dedicated for use by the
TV only.
Enter YOUR E-mail here
Advanced
Test
Cancel
Done
Note: The e-mail address assigned to the TV must be a
dedicated POP3 address, different from your personal
e-mail address. Assigning your personal e-mail
address to the TV will eventually lead to the deletion of
all of your personal e-mails (including attachments).
This is NOT covered under the Toshiba warranty.
5
Enter the required data in the fields.
See “Description of fields in the E-mail Scheduling Setup
window” (- page 74) for details on the settings for these
fields.
• For the fields listed below, press Bor bto highlight the
field, and then press C or c to select On or Off:
b) A personal e-mail address (different from the TV’s
dedicated e-mail address) from which you can send
e-mails to the TV.
– E-mail Scheduling
– ID Required
c) Login and password settings for the TV’s POP3 e-mail
account.
d) Name or IP address of the incoming (POP3) mail
server.
e) Name or IP address of the outgoing (SMTP) mail
server.
– E-mail Authorization
• For the fields listed below, press Bor bto highlight the
field, press T to open the keyboard window for the
selected field, and then enter the required information
using the on-screen keyboard:
– ID
To obtain the required e-mail services listed above, contact
your ISP.
To obtain the required addresses and settings listed above,
either contact your ISP or use the configuration utility for
your DSL/cable modem or router.
– E-mail Address
– Account
– Password
– Incoming Mail Server
– Outgoing Mail Server
– Authorized E-mail
Note:
•
Toshiba is not responsible for any damage or loss
caused directly or indirectly by the failure of the e-mail
scheduling feature to record content intended to be
recorded.
E-mail Address
XXXX@XXXXX.XX_
1
q
2
3
e
4
r
5
t
6
y
7
u
8
i
9
o
0
p
-
[
=
]
•
Toshiba is not responsible for, nor has any control over,
any content recorded and/or viewed using the e-mail
scheduling feature. Further, the e-mail scheduling
feature is not meant to be used for unauthorized
recording and/or viewing of copyrighted works.
w
a
s
d
f
g
h
j
k
l
;
'
z
x
c
v
b
n
m
,
.
/
Shift
Done
BS
Cancel
Clear
See “USING THE ON-SCREEN KEYBOARD”
(- page 65) for instructions on entering data in the fields
using the on-screen keyboard.
•
The unauthorized recording, use, distribution, or
revision of television programs, videotapes, DVDs, and
other materials is prohibited under the Copyright Laws
of the United States and other countries, and may
subject you to civil and criminal liability.
For home network troubleshooting tips, see Chapter 8.
70
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 71 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
6
When you are finished entering all characters for the
selected field, highlight Done and press T.
9
To exit the E-mail Scheduling Setup window and
save your settings, highlight Done and press T.
To exit the E-mail Scheduling Setup window without
saving your settings, highlight Cancel and press T.
E-mail Scheduling Setup
Please enter your E-mail Setup Information.
E-mail Scheduling
ID Required
On
On
IMPORTANT NOTE
ID
XXXXXXXXXXXXXXXX
E-mail Address
Account
To use e-mail scheduling, you must first set up the TV
Guide On Screen™ system. E-mail scheduling will not
be available unless the TV Guide On Screen™ system is
fully operational. See the separate TV Guide On Screen™
Interactive Program Guide for details on setting up the
TV Guide On Screen™ system.
Password
Incoming Mail Server
Outgoing Mail Server
E-mail Authorization
Authorized E-mail
On
Enter YOUR E-mail here
Advanced
Test
Cancel
Done
If you experience any issues with e-mail scheduling, please
contact the following:
7
8
Highlight Test and press T to test the e-mail setup.
During testing, the TV will display the message “Testing
E-mail.”
• In the U.S., call TACP Consumer Solutions at
customersupport/contact.asp
.
Note: Depending on your configuration, the e-mail test
can take several minutes. Do not press O during this
time.
• In Canada, call TCL Customer Service at
When testing is finished, a message will appear indicating
whether the e-mail test passed or not.
For home network troubleshooting tips, see Chapter 8.
If the e-mail test passes:
a) The “Test Passes” message (shown below) will appear.
E-mail Scheduling Setup
Please enter your E-mail Setup Information.
E-mail Scheduling
ID Required
ID
On
On
XXXXXXXXXXXXXXXX
Address
E-Tmeaisl ting E-mail
A
Test Passes
P
I
Outgoing Mail Server
E-mail Authorization
Authorized E-mail
OK
On
Enter YOUR E-mail here
Cancel Done
Advanced
Test
b) Go to step 9.
If the e-mail test does not pass:
a) An error message and code will appear on-screen
(similar to the example below).
E-mail Scheduling Setup
Please enter your E-mail Setup Information.
E-mail Scheduling
ID Required
ID
On
On
XXXXXXXXXXXXXXXX
E-mail Address
Testing E-mail
A
_
Error Sending and Receiving Mail (30 30)
P
OK
I
Outgoing Mail Server
E-mail Authorization
Authorized E-mail
On
Enter YOUR E-mail here
Advanced
Test
Cancel
Done
b) Locate the error code in the “TESTING E-MAIL”
ERROR CODES table (- page 73) and try the
solutions.
Note: The first number in the error code denotes an
error that occurs when the TV is receiving an e-mail; the
second number denotes an error that occurs when the
TV is sending an e-mail.
c) Repeat steps 1–8.
71
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 72 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
SMTP Port number:
Setting up SMTP authentication
Denotes the port number used by the user’s SMTP
(outgoing mail) server. This is set to 25 by default. Some
ISPs block this port to prevent mail relay attacks and
specify an alternate port.
If your e-mail provider does not allow unknown e-mail clients
to send e-mail through them (requires authentication), or uses
port numbers different from the default, you will need to fill
out the fields in the advanced section of the e-mail scheduler
setup.
Check for e-mails every:
This field controls the frequency of checking e-mail.
Options are 5 min, 15 min, 30 min, and 1 hour.
To set up SMTP authentication:
4
When you are finished, highlight Basic and press T to
return to the E-mail Scheduling Setup window. To save
your entries and exit the window, highlight Done and
press T. To exit the window without saving any entries,
highlight Cancel and press T.
1
2
Repeat steps 1-4 of “Setting up E-mail Scheduling” on
page 70.
Press the B, b, C and c buttons to highlight the
Advanced button on the screen and press T.
Another E-mail Scheduling Setup window will appear.
Note: There are several techniques used for SMTP
E-mail Scheduling Setup
Please enter your E-mail Setup Information.
authentication by e-mail providers. Only the most commonly
used techniques (Network address-based, “POP before
SMTP,” and “AUTH LOGIN”) are provided for your TV e-mail
scheduler. SSL and TLS are currently not supported.
SMTP Authentication
SMTP Username
Off
SMTP Password
POP port number
110
25
SMTP port number
Check for new emails every
5
min
Basic
3
Enter the data in the fields as you did in step 5 of “Setting
up E-mail Scheduling” on page 70. The fields and their
descriptions are as follows:
SMTP Authentication:
This field controls the SMTP authentication feature, and
is set to OFF by default. Setting this to “Same as POP”
fills the SMTP Username and SMTP Password fields with
the data filled in the “Account” and “Password” fields.
Select “Different” if the username and password for your
outgoing (SMTP) mail server are different from your
incoming (POP3) mail server.
SMTP Username:
This field holds the user name required by the SMTP
(outgoing email) server. This is typically the same as the
“Account” field, but may be different depending on the
ISP/SMTP server used. This field is enabled only if SMTP
authentication field above is set to “Different.”
SMTP Password:
This field holds the password required by the SMTP
server. This is typically the same as the “Password” field
used to receive e-mails, but may be different depending on
the ISP/SMTP server used. This field is enabled only if
SMTP authentication field (described above) is set to
“Different.”
POP Port number:
Denotes the port number used by the user’s POP3
(incoming mail) server. This is set to 110 by default.
72
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 73 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
“TESTING E-MAIL” ERROR CODES
Code
Description
Solutions
–1
The TV was able to connect to the
e-mail server(s) but could not log on.
• If you receive the message “Error Sending Mail (–1),” the TV may not
have received the test e-mail. Send another test e-mail to the TV using
the “HELP request e-mail” format (- page 78).
• Make sure the TV Guide On Screen™ system was set up properly. See
“IMPORTANT NOTE” on page 71.
• Make sure you entered the correct information for the following fields
in the TV’s “E-mail Scheduling Setup” window (confirm this
information with your ISP):
–“Incoming Mail Server” and “Outgoing Mail Server” names (or
IP addresses).
–“Account” (user name) and “Password” for the TV’s e-mail
account.
–“E-mail Address” for the TV.
• Check with your ISP to make sure your TV’s e-mail account has been
activated.
• Check with your ISP to make sure their servers support POP3 and SMTP
protocols without secure password authentication or secure connections.
28
The TV could not resolve the e-mail
server name(s)/address(es).
• Make sure you entered the correct information for the following fields
in the TV’s “E-mail Scheduling Setup” window (confirm this
information with your ISP):
–“Incoming Mail Server” and “Outgoing Mail Server” names (or
IP addresses).
–“IP,” “Netmask,” “Gateway,” and “DNS” settings (applicable if
you manually set up the network address).
• Make sure all cables are connected properly and securely.
• Check your router hardware/settings to make sure your Internet service
is currently available (especially if the e-mail test takes several minutes
to complete).
35
The e-mail server name(s)/address(es)
were resolved correctly, but TV could
not log on to the servers.
• Make sure you entered the correct information for the following fields
in the TV’s “E-mail Scheduling Setup”:
––Username and password.
–“Incoming Mail Server” and “Outgoing Mail Server” names (or
IP addresses).
–“IP,” “Netmask,” “Gateway,” and “DNS” settings (applicable if
you manually set up the network address).
• Make sure all cables are connected properly and securely.
• Check your router hardware/settings to make sure your Internet service
is currently available.
73
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 74 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
“Account” field
Description of fields in the “E-mail
Scheduling Setup” window
Use the on-screen keyboard to enter the TV’s e-mail account
login. Depending on your ISP, this may be the entire e-mail
address or just the characters in the e-mail address before the
“@” sign.
For instructions on entering data in these fields, see step 5
under “Setting up e-mail scheduling” (- page 70).
E-mail Scheduling Setup
Please enter your E-mail Setup Information.
“Password” field
E-mail Scheduling
ID Required
On
On
Use the on-screen keyboard to enter the password for the TV’s
e-mail account.
ID
XXXXXXXXXXXXXXXX
E-mail Address
Account
Password
Note: To help protect your other personal Internet or e-mail
accounts, create a password that is significantly different from
any of your usual passwords and security PINs (e.g., different
from your e-mail password, banking log-ons, social security
code, etc.).
Incoming Mail Server
Outgoing Mail Server
E-mail Authorization
Authorized E-mail
On
Enter YOUR E-mail here
Advanced
Test
Cancel
Done
“E-mail Scheduling” field
You can select On or Off for the E-mail Scheduling field.
– When this field is set to On, it will be possible for the TV
to receive e-mails from any PC to remotely schedule and
modify recordings and reminders.
“Incoming Mail Server” field
Use the on-screen keyboard to enter the incoming (POP3) mail
server that hosts the TV’s e-mail account.
Note: The TV does not support encrypted e-mail.
– When this field is set to Off, it will not be possible for the
TV to receive any e-mail, the other fields in this window will
be disabled (“grayed out”), and it will not be possible to
remotely schedule recordings or reminders via e-mail.
“Outgoing Mail Server” field
Use the on-screen keyboard to enter the outgoing (SMTP) mail
server associated with the TV’s e-mail account. (The TV will
use this server for sending reply e-mails to your personal
e-mail account.)
Also see the “Security settings” table on the next page.
“ID Required” field
You can select On or Off for the ID Required field.
“E-mail Authorization” field
You can select On or Off for the “E-mail Authorization”
– When this field is set to On (recommended), the ID you
entered in the “ID” field must be included in all e-mails you
send to the TV. This is a security feature to protect your TV
from unauthorized e-mail access.
– When this field is set to Off, you do not need to include the
ID in e-mails you send to the TV.
field.
– When this field is set to On (recommended), the TV will
only accept e-mails from the e-mail address you specify in
the “Authorized E-mail” field (e.g., your personal e-mail
address). The TV will delete any e-mails not sent from this
authorized e-mail address.
Also see the “Security settings” table on the next page.
This is a security feature to protect the TV from
unauthorized e-mail access and from replying to
unwanted e-mail, such as spam.
– When this field is set to Off, it will be possible for the TV
to accept e-mails from any e-mail address (depending on the
other settings in the “E-mail Scheduling Setup”
window).
“ID” field
Use the on-screen keyboard to enter six to 16 numbers and/or
letters to create your ID (spaces and punctuation are not
allowed).
Also see the “Security settings” table on the next page.
Note:
Also see the “Security settings” table on the next page.
• To help protect your privacy, you may want to choose an ID
that is different from any of your usual passwords or security
PINs (e.g., different from your personal e-mail password,
banking login code, social security number, etc.).
“Authorized E-mail” field
Enter the single e-mail address that is authorized to send
e-mails to the TV (e.g., your personal e-mail address).
– To enable this field, you must set the “E-mail
Authorization” field to On.
– This field can be left blank if you have the “E-mail
Authorization” field set to Off.
Also see the “Security settings” table on the next page.
• The ID is case sensitive.
“E-mail Address” field
Use the on-screen keyboard to enter the TV’s dedicated e-mail
address (different from your personal e-mail address). You
will send e-mails to this address to add, modify, or delete
schedules and reminders.
For home network troubleshooting tips, see Chapter 8.
74
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 75 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
Security settings
(Results of various setting combinations when the “E-mail Scheduling” field is set to ON in the “E-mail Scheduling Setup”
window)
“E-mail
“E-mail
“ID
Required”
field
“Authorized
E-mail” field
“ID”
field
Level of security
Scheduling” Authorization”
Result
field
field
The TV will only accept e-mails
from the one e-mail address
specified in the “Authorized
High*
[default settings]
(Recommended)
Enter single
E-mail address
Enter E-mail” field that also include the
ON
ON
ON
ID
“ID” in the body of the e-mail. All
other e-mails received by the TV
(except GET and HELP
commands) will be deleted.
The TV will only accept e-mails
from the one e-mail address
specified in the “Authorized
E-mail” field. All other e-mails
received by the TV will be deleted.
Enter single
E-mail address
Medium
Low
ON
ON
ON
ON
OFF
ON
—
The TV will accept e-mails from
any e-mail address that includes
the “ID” in the body of the e-mail.
All other e-mails received by the
TV will be deleted.
Enter
ID
OFF
OFF
—
—
The TV will accept e-mails from
any e-mail address (including
unwanted e-mails, such as spam)
and will reply to those e-mails with
a failure acknowledgment.
None
(Not recommended)
OFF
—
* The “High” settings are the default settings. To help prevent the TV from receiving or sending unwanted e-mails (including e-mails that contain
information about the programs the TV is set to record), it is recommended that you not change these settings unless you need to diagnose
a problem or deal with a unique user situation.
75
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 76 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
Sending a request e-mail to the TV
G. Using e-mail scheduling
To send a request e-mail to the TV:
You can use the e-mail scheduling feature to schedule and
delete recordings and reminders by sending a “request e-mail”
to the TV’s e-mail address from any PC.
1
Format the e-mail following according to the instructions
under “Formatting a request e-mail” on the next page.
The four commands the TV will accept are ADD, DELETE,
2
3
Send the e-mail to the TV.
GET, and HELP, as described in this section.
After the TV receives and processes the e-mail, the TV
will send a reply e-mail indicating whether the e-mailed
request succeeded or failed. See “Receiving an e-mail
from the TV” (- page 78).
If you have not already done so, follow the instructions in
sections A and B (- page 60), and in section F (- page 70),
before proceeding.
When a recording is scheduled via e-mail, the recording device
used will be the VCR connected to the TV's analog A/V OUT
terminals (see item 4 on page 9 for the location of the A/V
OUT terminals; see the separate Installation Guide for various
VCR connection examples).
E-mail parameters
Note: Some e-mail clients automatically insert e-mail
signatures, which the TV will try to process. These may
generate unwanted error messages.
• The maximum allowable e-mail size is 16 KB. E-mails over
16 KB will be automatically deleted.
• E-mails sent to the TV cannot contain any attachments. The
TV will automatically delete any e-mail with an attached
file.
• E-mails can be formatted either Plain Text or Rich Text
Format (HTML style).
• E-mails sent to the TV that are not properly formatted,
are from the wrong e-mail address, or have the wrong ID
(if specified) will be deleted.
• All e-mails sent to the TV will be deleted eventually.
Note:
•
Toshiba is not responsible for any damage or loss
caused directly or indirectly by the failure of the e-mail
scheduling feature to record content intended to be
recorded.
•
Toshiba is not responsible for, nor has any control over,
any content recorded and/or viewed using the e-mail
scheduling feature. Further, the e-mail scheduling
feature is not meant to be used for unauthorized
recording and/or viewing of copyrighted works.
•
The unauthorized recording, use, distribution, or
revision of television programs, videotapes, DVDs, and
other materials is prohibited under the Copyright Laws
of the United States and other countries, and may
subject you to civil and criminal liability.
76
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 77 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
Formatting a request e-mail
Sample request e-mails
• The examples shown below are for illustration purposes
only.
Recognized tags
• Styles applied to the sample e-mail text (such as bold, italic,
and underline) are for illustration purposes only. You do not
need to style the text in your request e-mails.
• The only text in a request e-mail that is case sensitive is the
ID. All other text is not case sensitive.
When you send an ADD, DELETE, GET, or HELP request
e-mail to the TV, the TV will recognize only the tags listed
below. These tags (and their accompanying data) must be
listed in the body of the request e-mail in the following order:
• ID [your ID*]
(not required if you set the “ID Required” field to Off)
ADD request e-mail
The ADD request allows you to schedule a new recording or
reminder.
The required tags for an ADD request e-mail are (in this
order):
• ID [your ID*]
• COMMAND ADD
(or COMMAND DELETE or COMMAND GET or
COMMAND HELP)
• INPUT [name of input to record]
• CHANNEL [channel number of recording or reminder]
• DATE [date of recording or reminder]
(not required if you set the “ID Required” field to Off)
• COMMAND ADD
• START TIME [start time of recording or reminder]
• DURATION [length of recording or reminder]
• INPUT [name of input]
• TYPE RECORD
(or TYPE REMIND)
• CHANNEL [channel number of recording or reminder]
• DATE [date of recording or reminder]
• START TIME [start time of recording or reminder]
• DURATION [length of recording or reminder]
• TYPE RECORD ...or... TYPE REMIND
Tag and data formats
The data for each tag can be formatted in various ways, as
described in the following table:
Tag formats
Data formats
Sample ADD request e-mail
Sample ADD request e-mail
to schedule a new recording:
to schedule a new reminder:
[6- to 16-character alphanumeric]
MYID1234* (example only)
ID*
To: [TV’s email address]
[Subject can be left blank]
To: [TV’s email address]
[Subject can be left blank]
ADD
COMMAND DELETE (or DEL)
ID MYID1234*
COMMAND ADD
INPUT ANT-1
CHANNEL 102-1
DATE 06/10/2005
START TIME 7 PM
DURATION 2H15M
TYPE RECORD
ID MYID1234*
cmd add
input cb
ch 4
date 7-4
start 8:30pm
dur 1hr
type remind
(or CMD)
GET
HELP
ANT1 (or ANT-1)
ANT2 (or ANT-2)
INPUT
(or INP)
CABLEBOX (or CB)
SETTOPBOX (or STB)**
CHANNEL
(or CH)
5 … 38 … 100 … 5-1 … 120-1
[Use a hyphen for digital channels]
GET request e-mail
When you send a GET request e-mail to the TV, you will
receive a reply e-mail that lists all currently scheduled
recordings and/or reminders.
The only required tag and data for a GET request e-mail is
GET.
7-4 (or 7-4-05 or 7-4-2005 or 7/4/05, etc.)
[If the year is not specified, the current
year is assumed.]
DATE
STARTTIME
8AM ... 9:30PM
[Noon = 12PM; Midnight = 12AM]
(or START)
Sample GET request e-mail:
DURATION
(or DUR)
30M (or 30MIN)
2H30M (or 2HR30MIN or 2:30)
To: [TV’s email address]
[Subject can be left blank]
RECORD (or REC)
REMIND (or REM)
TYPE
GET
* The ID is case sensitive. The ID tag is required only if you created
an ID in the “ID” field and set the “ID Required” field to On. If you set
the “ID Required” field to Off, you do not need to include the ID tag
line in your request e-mail. See “Description of fields in the E-mail
Scheduling Setup window” (- page 74).
**“Set-top box” and “STB” refer to a satellite set-top box.
(continued)
77
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 78 Tuesday, June 27, 2006 1:43 PM
Chapter 7: Using the THINC™ home network feature
DELETE request e-mail
The DELETE request allows you to cancel a scheduled
recording or reminder.
The required tags for a DELETE request e-mail are (in this
order):
• ID [your ID*]
(not required if you set the “ID Required” field to Off)
Receiving an e-mail from the TV
If the request e-mail was successful, the reply e-mail from
the TV to your PC will contain one of the following (or similar)
messages, depending on the command you sent to the TV:
• ADD SUCCESS
• DELETE SUCCESS
• GET SUCCESS
• COMMAND DELETE
• INPUT [name of input]
• HELP SUCCESS
If the request e-mail was not successful, the reply e-mail
from the TV to your PC will contain one of the following (or
similar) messages, depending on the command you sent to the
TV:
• FAILED – SCHEDULE CONFLICT.
The new recording or reminder you attempted to schedule
conflicts with an existing one that was previously scheduled.
• CHANNEL [channel number of recording or reminder]
• DATE [date of recording or reminder]
• START TIME [start time of recording or reminder]
• DURATION [length of recording or reminder]
• TYPE RECORD ...or... TYPE REMIND
If you want to schedule the new recording or reminder, you
will have to DELETE the existing one first, and then ADD
the new one.
Sample DELETE request
e-mail to delete an existing
recording:
Sample DELETE request
e-mail to delete an existing
reminder:
• FAILED – COULD NOT UNDERSTAND “Line x.”
The request e-mail has an error in the line of text referenced
in the error message. Correct the text and resend the e-mail.
• FAILED – NO DEVICE AVAILABLE.
Make sure you have a recording device connected to the TV
and that all cables are properly connected.
To: [TV’s email address]
[Subject can be left blank]
To: [TV’s email address]
[Subject can be left blank]
ID MYID1234*
COMMAND DELETE
INPUT ANT-1
CHANNEL 102-1
DATE 06/10/2005
START TIME 7 PM
DURATION 2H15M
TYPE REC
ID MYID1234*
cmd del
input cb
ch 4
date 7-4
start 8:30pm
dur 1hr
• FAILED – MISC ERROR.
Make sure all devices and cables are properly connected and
that the text in the body of your e-mail is correct, and then
send the corrected e-mail to the TV.
type rem
HELP request e-mail
Modifying an existing recording or
reminder
When you send a HELP request e-mail to the TV, you will
receive a reply e-mail that contains helpful information about
formatting a request e-mail (syntax, definition of the various
commands, etc.).
To modify an existing scheduled recording or
reminder:
The only required tag for a HELP request e-mail is HELP.
Sample HELP request
e-mail:
1
2
Send a DELETE request e-mail to cancel the existing
recording or reminder.
To: [TV’s email address]
[Subject can be left blank]
Send an ADD request e-mail to schedule the modified
recording or reminder.
HELP
For home network troubleshooting tips, see Chapter 8.
* The ID is case sensitive.
The ID tag is required only if you created an ID in the “ID” field and
set the “ID Required” field to On. If you set the “ID Required” field
to Off, you do not need to include the ID tag line in your request
e-mail. See “Description of fields in the E-mail Scheduling Setup
window” (- page 74).
78
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 79 Tuesday, June 27, 2006 1:43 PM
Chapter 8: Troubleshooting
Picture problems
General picture problems
General troubleshooting
•
Check the antenna/cable connections (- Installation
Guide).
Before calling a service technician, please check this chapter
for a possible cause of the problem and some solutions you can
try.
•
Press + on the remote control or TV and select a valid
video input source (- page 32). If no device is
connected to a particular input on the TV, no picture will
display when you select that particular input source. For
device connection details, see the Installation Guide.
Antenna reception may be poor. Use a highly directional
outdoor antenna (if applicable).
Black box on screen
•
The Closed Caption feature is set to one of the Text
modes (T1, T2, T3, or T4). Set the Closed Caption
feature to Off (- page 43).
•
•
The station may have broadcast difficulties. Try another
channel.
TV plays a recorded announcement when LEDs are blinking
•
When certain non-standard conditions occur, the LEDs
on the TV will blink and the TV will play a recorded
“voice announcement” describing the condition (see
“LED indications” on page 83 for details).
•
•
Adjust the picture qualities (- page 42).
If you are using a VCR, make sure L on the remote
control is set to the correct mode (see item 22 on page
13).
•
•
If you have two VCRs connected to your TV, make sure
you have not connected the same VCR to the TV’s output
and input connections at the same time (- Installation
Guide).
Do not connect both a standard video cable and an S-
video cable to the same set of VIDEO inputs (VIDEO 1,
or VIDEO 2) at the same time (- Installation Guide).
TV stops responding to controls
•
If the TV stops responding to the controls on the remote
control or TV control panel and you cannot turn off the
TV, press and hold the POWER button on the TV control
panel for 5 or more seconds to reset the TV.
Other problems
If your TV’s problem is not addressed in this
Noisy picture
•
•
If you are watching an analog channel (off-air broadcast
Troubleshooting section or the recommended solution
has not worked, use the Reset Factory Defaults procedure
(- page 31).
or Cable TV), you can set the CableClear® feature to
AUTO to reduce visible interference in the TV picture
(- page 55).
TV will not turn on
Video Input Selection problems
•
If the Input Selection window does not appear when
you press + on the remote control or TV, press + a
second time, which will change to the next video input
source and display the Input Selection window.
•
•
•
Make sure the power cord is plugged in, and then press
p.
The remote control batteries may be dead. Replace the
batteries or try the control panel buttons.
If you have recently replaced the lamp unit, make sure the
lamp unit and lamp unit door are installed properly
(- pages 84–86).
Cannot view external signals or channel 3 or 4
•
If you cannot view signals from external devices
connected to VIDEO 1, VIDEO 2, or ColorStream®, or
from channels 3 or 4, make sure the Input Lock is set to
Off (- page 50).
•
•
The lamp unit may need to be replaced (-pages 84–86).
Also see “LED indications” (- page 83).
If the TV is powered off and then quickly on again when
the lamp unit is hot, it may take several minutes for the
picture to appear on-screen. This is a property of DLP TV
lamp technology and is NOT a sign of malfunction. For
details, see “IMPORTANT NOTICE ABOUT HOT
LAMP RESTART” (- page 3).
Poor color or no color
•
The station may have broadcast difficulties. Try another
channel.
•
•
Adjust the Tint and/or Color (- page 42).
When the ColorStream® signal source is active, the
VIDEO OUT terminal does not output video. To receive
video from the VIDEO OUT terminal, a standard video
or S-video IN connection must be used instead of the
ColorStream® connections.
POP problems
If you label all of the inputs as “Hide,” the POP feature
•
will be disabled. If you then attempt to access the POP
feature, the message “Not Available” will appear on-
screen (- page 40).
(continued)
79
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 80 Tuesday, June 27, 2006 1:43 PM
Chapter 8: Troubleshooting
Picture brightness changes soon after turning on TV
Remote control problems
•
If you set the lamp mode to Low Power, each time you
turn on the TV, the lamp will start out in High Bright
mode but will switch to Low Power mode after a short
period of time. You may notice a change in screen
brightness when this happens. This is normal and is not a
sign of malfunction (- page 57).
•
•
•
•
Make sure the remote control is set to the correct device
mode (- page 16).
Remove all obstructions between the remote control and
the TV.
The remote control batteries may be dead. Replace the
batteries (- page 11).
Your TV remote control may not operate certain features
on your external device. Refer to the owner’s manual for
your other device to determine its available features. If
your TV remote control does not operate a specific
feature on another device, use the remote control that
came with the device (- page 16).
Poor composite or S-video picture
•
If the TV is connected to an external A/V device (e.g.,
DVD player, video game system, set-top box, etc.) try
using a ColorStream or HDMI video connection
instead.
Picture and sound are out of sync
•
As with all products that contain a digital display, in rare
instances, when viewing certain content (e.g.. television
broadcasts, video games, DVDs), you may notice that the
sound and picture are slightly out of sync. This
•
If the TV still does not act as expected, use the Reset
Factory Defaults procedure (- page 31).
Channel tuning problems
phenomenon can be caused by various factors including,
without limitation, video processing within the TV, video
processing in an attached gaming system, and video
processing or different compression rates used by
broadcasters in their programming. You may want to try
one or more of the following suggestions, which may
help to reduce the effect of this phenomenon:
– If the TV is connected to an A/V receiver that has a
programmable audio delay feature, use this feature to
help synchronize the sound to the picture.
•
Make sure the remote control is set to the correct device
mode (- page 16).
•
The channel may have been erased from the channel
memory by the Channel Add/Delete feature. Add the
channel to the channel memory (- page 27).
The channel may be blocked by the Channels Block
feature. Unblock the channel (- page 49).
If you are unable to tune digital channels, check the
antenna configuration (- page 25). If you are still
unable to tune digital channels, clear all channels from
the channel list (-page 27) and reprogram channels into
the channel memory (- page 26). If you are still unable
to tune digital channels, use the Reset Factory Defaults
procedure (- page 31). Also see “TV stops responding
to controls” and “Other problems” (- page 79).
•
•
– If you notice this phenomenon only on certain TV
channels, please contact your local broadcast, cable, or
satellite provider to inform them of this issue.
Sound problems
•
Check the antenna/cable connections (- Installation
Guide).
The station may have broadcast difficulties. Try another
channel.
Closed caption problems
•
•
If the program or video you selected is not closed-
captioned, no captions will display (- page 43).
If text is not available, a black rectangle may appear.
If this happens, turn off the closed caption feature (-
page 43).
•
•
The sound may be muted. Press z.
•
If you hear no sound, try setting the MTS feature to
Stereo mode (- page 45).
•
•
Make sure the Speakers function in the Audio Setup
menu is set correctly (- page 46).
If you are not receiving a second audio program from a
known SAP source, make sure the MTS feature is set to
SAP mode (- page 45).
If you hear audio that seems “incorrect” for the program
you are watching (such as music or a foreign language),
the SAP mode may be on. Set the MTS feature to Stereo
mode (- page 45).
When using an external audio amplifier, if you connect
the amplifier to the VAR. AUDIO OUT terminals, the
volume of the TV and amplifier must be set above 0 or
you will not hear any sound (- Installation Guide).
•
A closed-caption signal may not display correctly in the
following situations: a) when a videotape has been
dubbed; b) when the signal reception is weak; or c) when
the signal reception is nonstandard (- page 43).
Rating blocking (V-Chip) problems
•
•
•
If you forget your PIN code: While the PIN code entering
screen is displayed, press E four times within 5
seconds. The PIN code you previously stored will be
cleared (- page 47).
The V-Chip feature is available for the U.S. V-Chip
system only (- page 48).
•
80
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 81 Tuesday, June 27, 2006 1:43 PM
Chapter 8: Troubleshooting
Some files in the shared folder are not played
Recording problems
•
Only the first 200 MP3 files found will be played. Folders
nested 10 or more levels below the shared folder are not
searched.
•
If you use the TV’s remote control to start recording, you
will not be able to change inputs (-page 32) or open the
POP window (- page 40). If you attempt to do so, the
message “Not Available While Recording” will appear
on-screen.
If you are recording a digital channel, you can only
change analog channels while recording is in progress. If
you are recording an analog channel, you can only
change digital channels while the recording is in
progress. This is because the TV tuner that is being
recorded (digital or analog) will be locked on the channel
that is currently recording.
The Audio Player plays (progress bar and animation
change) but audio is not heard
•
The volume level is not high enough or TV is muted.
•
Picture Viewer problems
“No pictures found” message is displayed.
•
Sharing is not correctly set up on the networked PC.
Make sure you connected your home network correctly
(- Installation Guide) and set up the network address
properly (- Chapter 7).
•
It is recommended that you use the TV’s remote control
to start recording. If you use a device other than the TV’s
remote control to start recording and then attempt to
access a feature that is normally denied during recording
(POP mode, changing inputs,) the recorded audio and/or
video may not be what you intended to record.
•
The JPEG files exceed the specified limits (- “Media
specifications” in Chapter 7).
Picture viewer option in menu is disabled.
•
There are no picture files in the networked PC's shared
folder(s).
•
Basic network setup and Home server setup were not
successfully performed.
Audio Player problems
The Audio Player stutters and/or stops when playing
files over the network
Picture is not displayed. Rectangle containing “X” is
displayed instead.
•
The networked PC is not available, was removed from
the network, or is in "hibernation." The Ethernet cables
are not connected properly. Check all cables for proper
connection.
Sufficient network band-width is not available. Turn off
any other file sharing programs, network-based games, or
other network-intensive operations while the Audio
Player is playing.
•
The picture file does not meet the specifications for the
Picture Viewer (- “Media specifications” in Chapter
7).
Picture is not listed at all.
•
•
There are no picture files in the networked PC’s shared
folder(s).
•
The number of pictures files found is more than the TV
can display.
“No media found” message is displayed
•
•
The picture file does not have a valid “.jpg” extension.
The file is too large or is otherwise not compatible with
the TV for display. See “Media specifications” in Chapter
7 for Picture Viewer and JPEG file specifications.
•
Sharing is not correctly set up on the networked PC.
Make sure you connected your home network correctly
(- Installation Guide) and set up the network address
properly (- Chapter 7).
•
The MP3 files exceed the specified limits (- “Media
specifications” in Chapter 7).
Home network troubleshooting
Title or artist name is not displayed
•
The MP3 file does not contain valid meta-data or does not
meet supported specifications (- “Media
specifications” in Chapter 7).
Basic network setup problems
Cannot connect to network
The Audio Player takes almost a minute to start
•
•
Check the modem and splitter connections.
Make sure the splitter is connected to the modem or
telephone jack correctly (- page 60).
•
Sufficient network band-width is not available. Turn off
any other file sharing programs, network-based games, or
other network-intensive operations while the Audio
Player is playing.
•
•
Confirm your modem’s operation with this manual.
Make sure your network address and e-mail account are
set up correctly (- Chapter 7).
•
The shared folder has too many files or sub-folders. If the
shared folder on the networked PC contains a large
number of files or nested directories, it may take over a
minute for the Audio Player to locate all playable files.
No network connection
•
The Ethernet cables are not connected properly or at all.
Connect all cables(- Install Guide).
The File is displayed but is always skipped
The file is not a valid or supported MP3 file.
•
•
Make sure the modem’s power cord is plugged in.
Make sure your network address and e-mail account are
set up correctly (- Chapter 7).
•
(continued)
81
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 82 Tuesday, June 27, 2006 1:43 PM
Chapter 8: Troubleshooting
Automatic setup fails
E-mail scheduling problems
Cannot schedule a recording by e-mail
•
The Ethernet cables are not connected properly or at all.
Connect all cables(- Installation Guide).
•
•
•
Select “Test” to confirm the e-mail scheduling setup
(- page 71).
Select “Done” after setting up e-mail scheduling
(- page 71).
•
The DHCP service is not enabled on the router, or no
router is present. Refer to your router’s documentation
for instructions on enabling DHCP. If you do not have a
router, you must manually set up the network address
(- page 61).
See Chapter 7 in this manual.
•
Internet service is not available. Check your cable/DSL
modem or contact your ISP for Internet service issues.
E-mail test fails after waiting a long time
•
The Ethernet cables are not connected properly or at all.
Connect all cables(- Installation Guide).
The DNS (domain name server) is not set up correctly.
Check the network settings.
The SMTP and POP3 server settings are incorrect.
The “E-mail Address,” “Account,” or “Password”
settings are incorrect. User names and passwords are
generally case sensitive.
Manual setup fails
•
•
The Ethernet cables are not connected properly or at all.
Connect all cables (- Installation Guide).
The TV IP address is the same as the networked PC’s.
The TV IP address must be different from the PC’s IP
address.
The TV IP address is not on the same subnet as the
networked PC’s. For example, if the PC has IP
192.168.0.100 with netmask 255.255.255.0, and the TV
has IP 192.168.0.200 with netmask 255.255.255.0, then
they are both on same subnet. Conversely, if the PC has
IP 192.168.1.100 with netmask 255.255.255.0, and the
TV has IP 192.168.0.200 with netmask 255.255.255.0,
then they are on DIFFERENT sub-nets.
•
•
•
•
Receiving succeeds but sending fails, or vice-versa
•
•
The SMTP and POP3 server settings are incorrect.
The “E-mail Address,” “Account,” or “Password”
settings are incorrect. User names and passwords are
generally case sensitive.
•
Your Internet service provider may not support SMTP or
POP3 protocols. Check with your ISP for details on
supported protocols.
Unstable network connection
Unplug the Ethernet cables, and then connect them again.
•
The e-mail test passes, but the TV never responds to
the e-mails
Home server setup problems
•
Email scheduling is turned OFF. Turn e-mail scheduling
ON (page 70).
The PC (“Home Server”) name is not displayed
•
The Ethernet cables are not connected properly or at all.
Connect all cables (- Installation Guide).
•
The sender’s e-mail address is not the “Authorized E-
mail Address.” Make sure the e-mail address you are
using to send e-mails to the TV is the same as the
“Authorized E-mail Address” in the TV’s e-mail
scheduling setup. See “Setting up e-mail scheduling” in
Chapter 7.
•
The network setup on the PC is incorrect. Make sure both
the PC and TV are using the same network type (DHCP/
manual) and have compatible network settings.
The networked PC does not have shared folders set up
correctly. See “Setting up file sharing on your PC” in
Chapter 7 for details.
There are no master browsers on the network. To
configure your networked PC to be the master browser of
its subnet, refer to your operating system user guide or
consult an IT professional.
•
•
Note: Responses from the TV can often be delayed a few
minutes, depending on e-mail/Internet service
availability when you send the request e-mail.
An ADD or DELETE request e-mail returns an
“INVALID MAIL VERIFICATION ID” reply
•
The e-mail authorization ID is not specified or is different
from the TV settings. See “Setting up e-mail scheduling”
in Chapter 7.
•
Too many sharing devices are connected. You cannot
connect more than 16 sharing devices at one time.
The PC (“Home Server”) name is displayed but the
shared folder(s) are not displayed.
The e-mail was successfully sent but the recording or
reminder did not work.
•
The networked PC does not have shared folders set up
correctly. See “Setting up file sharing on your PC” in
Chapter 7 for details.
•
See “Setting the time and date” on page 28.
•
The TV’s user name and password do not match the PC’s.
Make sure the user name and password settings in the TV
exactly match the settings in the networked PC. User
names and passwords are generally case sensitive.
82
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 83 Tuesday, June 27, 2006 1:43 PM
Chapter 8: Troubleshooting
LED indications
The yellow, blue, and red/green LED lights on the TV (at the bottom center of the TV) indicate the TV’s status, as described below.
Note: If the TV loses A/C power (e.g., a power outage occurs or the power cord is unplugged), when power is restored, the yellow
LED will blink while the TV is booting until the remote control is usable. This is normal and is not a sign of malfunction.
TV Front
“Voice announce” feature
LAMP
Yellow LED
Blue LED
When certain non-standard conditions occur, the LEDs
on the TV will blink and the TV will play a recorded
POWER
“voice announcement” describing the condition (see the table below
for the specific conditions that include a voice announcement).
To repeat the voice announcement and hear additional information,
press the MENU button on the TV while the LEDs are blinking.
TIMER
REC
Red/Green LED
Voice
Announce
LED Indication
Condition
Solution
1) Blue is ON (solid).
The TV is operating
properly.
–
–
2) Yellow blinks.
In LPS mode (standby
with Quick Restart ON).
See “Setting the Quick Restart™ feature” (- page 30).
–
3) Blue is ON (solid).
The lamp is not working
properly.
The TV will automatically try to restart itself eight times
(see item #4).
Yellow blinks.
Note: If the TV is powered off and then quickly on again
when the lamp unit is hot, it may take several minutes
for the picture to appear on-screen. This is a property of
DLP TV lamp technology and is NOT a sign of
malfunction. For details, see “Setting the Quick
Restart™ feature” and “IMPORTANT NOTICE ABOUT
HOT LAMP RESTART” (- page 30).
–
4) Yellow is ON
The lamp is not working
properly after the eighth
automatic restart (see
item #3).
Turn the TV OFF and then ON again. If the problem
persists, contact Consumer Solutions at
1-800-631-3811.
“Lamp not
working”
(solid). Red blinks.
5) Yellow is ON
The lamp unit door is not
seated properly.
Turn OFF the TV and unplug the power cord. Review
“Lamp unit replacement and care” in Chapter 9 to
ensure that the lamp door is installed securely.
“Lamp door is
open.”
(solid).
6) Red blinks.
Fan stopped
(light engine).
“Fan
stopped.”
7) Blue is ON (solid).
Fan stopped
(CableCard).
–
–
–
Green blinks.
8) Blue blinks slowly.
Abnormal operation of
BUS line.
Turn OFF the TV and unplug the power cord. Plug the
power cord in again and turn ON the TV.
9) Blue blinks quickly. Power Protect
Detection.
10)Blue blinks quickly.
The color wheel has
stopped.
“Color wheel
stopped.”
Red blinks.
11)Blue blinks quickly.
Yellow blinks.
An abnormal
temperature increase
has occurred.
Turn OFF the TV. Check to make sure none of the slots
or openings in the TV cabinet are covered, blocked, or
dusty. Turn ON the TV again.
“Temperature
warning.”
Red blinks.
12)Red is ON (solid).
Recording in progress.
–
–
If, after trying the solution, the problem still exists:
• In the U.S., call TACP Consumer Solutions at 1-800-631-3811.
• In Canada, locate the nearest Toshiba authorized service depot by directing your web browser to www.toshiba.ca; click
“Home Entertainment,” and then click “Support.”
83
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 84 Tuesday, June 27, 2006 1:43 PM
Chapter 9: Appendix
When to replace the lamp unit
Lamp unit replacement and care
You should replace the lamp unit:
• if the picture darkens and/or colors fade;
• if the screen (lamp) does not light (LED indication #4,
- page 83); or
• if you hear a loud noise and the picture goes black, which
may indicate a lamp rupture (LED indication #4,
- page 83).
Replacing the lamp unit
(User-replaceable component)
WARNING: RISK OF ELECTRIC
SHOCK!
TO REDUCE THE RISK OF ELECTRIC
SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS
SPECIFIED HEREIN. REFER ALL SERVICING NOT
SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE
PERSONNEL. Failure to follow this WARNING may result in
death or serious injury.
To obtain a replacement lamp unit:
In the U.S.
In warranty:
call toll-free 1-800-631-3811.
Out of
warranty:
The light source for this TV is a mercury lamp with internal
atmospheric pressure that increases during use. The lamp has a
limited service life that varies depending on product use and
user settings.
consult your consumer electronics dealer.
In Canada
As is generally the case with all projection TVs that use
projection lamps as a light source, the brightness of the lamp
in this TV may vary somewhat over the expected service life
and will generally decrease over time. Because of the many
variables that can affect the useful service life of the lamp, your
experience may vary from other users.
Locate a Toshiba parts distributor by visiting
www.toshiba.ca. Click “Home Entertainment” and then
click “Support.”
Always replace the lamp unit with the model
currently recommended by Toshiba.
The correct lamp replacement part number is located
on the serial number label on the back of the
television and on the lamp unit.
For more information, please contact us at the
telephone numbers or websites listed above, as
applicable.
Note : The lamp is warranted only for the periods and to the
extent set forth in the Limited Warranty applicable to this set.
See “Limited United States Warranty” (- page 88) or “Limited
Canada Warranty” (- page 89), as applicable.
If you use the lamp beyond its service life:
• you may notice a reduction in the colors and/or brightness of
the picture; and
Using any lamp other than those recommended by
Toshiba may cause damage to the TV and/or lamp.
• the strength of the quartz glass in the lamp will be reduced
and the lamp may rupture (often making a loud noise when
this happens). If the lamp ruptures, the TV will not operate
until the lamp unit is replaced.
SUCH DAMAGE IS NOT COVERED UNDER YOUR
TOSHIBA WARRANTY.
CAUTION: Always handle the lamp unit
with care.
The lamp unit in this TV was designed for safe
replacement by consumers; however, if the lamp unit is
subjected to intentional abuse (such as excessive
mechanical abuse or handling by children or pets), the unit
may break, exposing sharp edges or pinch points.
84
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 85 Tuesday, June 27, 2006 1:43 PM
Chapter 9: Appendix
4
Using a manual Phillips screwdriver, loosen the two
screws on the lamp unit.
How to replace the lamp unit
WARNING: RISK OF ELECTRIC
SHOCK!
TO REDUCE THE RISK OF ELECTRIC
SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS
SPECIFIED HEREIN. REFER ALL SERVICING NOT
SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE
PERSONNEL. Failure to follow this WARNING may result in
death or serious injury.
Required tools:
Lamp unit screws
• Manual screwdrivers (Phillips and slotted)
• Soft, lint-free gloves
• Optional tool: 5/16" nut driver
WARNING: RISK OF ELECTRIC
SHOCK!
The lamp unit door is provided with an
1
Turn off the TV and unplug the power cord.
interlock to reduce the risk of electric shock and excessive
ultraviolet radiation. Never defeat its purpose or attempt
to service without removing the lamp unit door
completely. Failure to follow this WARNING may result in
death or serious injury.
WARNING: Eye damage may result from
directly viewing the light produced by
this lamp.
Always turn off the TV and unplug the power cord before
opening the lamp unit door.
5
Grasp the lamp unit handle and gently pull the lamp unit
straight out of the TV. Set the old lamp unit aside
(- “Disposing of the used lamp unit” on page 86).
2
STOP! Allow the lamp to cool for at least one (1) hour
before replacing it.
3
On the lamp unit door on the side of the TV, loosen the
screw using a manual screwdriver, and then remove the
lamp unit door.
NOTE: Wear soft, lint-free gloves when
replacing the lamp unit.
Lamp unit door detail
TV back
6
Carefully insert the new lamp unit straight into the TV
until it is fully seated.
Loosen screw
using manual
screwdriver
(continued)
85
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 86 Tuesday, June 27, 2006 1:43 PM
Chapter 9: Appendix
Note:
9
Replace the screw and tighten using a manual
screwdriver.
• Never subject the lamp unit to excessive shock.
• Never touch the lamp unit glass or otherwise get it dirty.
Doing so may affect the image quality and reduce the
service life of the lamp. See “Cleaning the lamp unit glass”
below.
CLEANING THE LAMP UNIT GLASS
If you accidentally touch the lamp unit glass or otherwise get
it dirty, wipe it with a lint-free lens cleaning cloth (such as a
cloth for cleaning camera lenses or eyeglasses).
Hand tighten using
a manual screwdriver
Lamp unit door
NOTE: Make sure the lamp unit door is installed
CAUTION
:
NEVER clean a hot lamp with any
type of flammable liquid or aerosol cleaning
agent. Many ordinary cleaning agents (such as
securely; otherwise, the TV may not turn on.
glass cleaners) contain chemicals that may be flammable at
certain temperatures. If the lamp unit is not allowed to cool for at
least one (1) hour, such chemicals may ignite.
10 Plug in the power cord and turn on the TV. After the initial
warmup period (which may take several seconds for full
picture brightness), the TV should operate normally. If
any of the following conditions exist, turn off the TV,
unplug the power cord, and repeat steps 1–9 to ensure that
the lamp unit and lamp unit door are installed correctly:
7
Using a manual Phillips screwdriver, tighten the two lamp
unit screws.
• No picture
• Dark picture
Note: Hand-tighten only. Do not use an electric
screwdriver.
• TV will not turn on
If, after repeating steps 1–9, the problem still exists:
• In the U.S., call TACP Consumer Solutions at
1-800-631-3811.
• In Canada, locate the nearest Toshiba authorized
service depot by directing your web browser to
then click “Support.”
Lamp unit screws
(use manual Phillips screwdriver only)
Disposing of the used lamp unit
NOTE : Make sure the lamp unit and screws are
installed securely; otherwise, the TV may not turn
on and the lamp life may be shortened.
• Place the used lamp unit in the empty box from the new unit.
• Keep the lamp unit out of reach of children and pets.
CAUTION: Always handle the lamp unit
with care.
8
Reattach the lamp unit door, making sure to insert the
hooks on the left side of the lamp unit door inside the
opening in the TV cabinet.
The lamp unit in this TV was designed for safe
replacement by consumers; however, if the lamp unit is
subjected to intentional or accidental abuse (such as
excessive mechanical abuse or handling by children or
pets), the unit may break, exposing sharp edges or pinch
points.
Insert the hooks inside the
TV cabinet opening.
• Dispose of the used lamp unit by the approved method for
your area.
NOTE: The lamp unit contains mercury.
Disposal of mercury may be regulated due to
environmental considerations. For disposal or
recycling information, contact your local authorities or the
Electronic Industries Alliance (www.eiae.org).
Lamp unit door
86
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 87 Tuesday, June 27, 2006 1:43 PM
Chapter 9: Appendix
HDMI™ INPUT:
HDMI compliant (type A connector)
Specifications
HDCP compliant
E-EDID** compliant
Note:
Suggested formats: 1080i, 480p, 480i, 720p
HDMI Audio: 2-channel L-PCM; 32/44.1/48 kHz
sampling frequency; 16/20/24 bits per sample
and Dolby Digital
•
•
•
This model complies with the specifications listed
below.
Designs and specifications are subject to change
without notice.
VIDEO/AUDIO OUTPUT (also for recording):
VIDEO: 1 V(p-p), 75 ohm, negative sync.
AUDIO: 150 mV(rms) (30% modulation equivalent,
2.2 k ohm or less)
This model may not be compatible with features and/or
specifications that may be added in the future.
VARIABLE AUDIO OUTPUT:
0–300 mV(rms) (30% modulation equivalent, 2.2 k
ohm or less)
Television System
NTSC standard
ATSC standard (8VSB)
Digital Cable (64 QAM, 256 QAM; in-the-clear,
unencrypted*)
DIGITAL AUDIO OUTPUT:
Optical type
G-LINK™:
3 V(p-p), 3.5 mm mono socket (IR blaster cables
supplied)
PC IN:
Mini D-sub 15 pin Analog RGB
PC AUDIO IN:
Channel Coverage
VHF: 2 through 13
UHF: 14 through 69
Cable TV: Mid band (A-8 through A-1, A through I)
Super band (J through W)
Hyper band (AA through ZZ, AAA, BBB)
Ultra band (65 through 94, 100 through 135)
150 mV(rms), 22 k ohm or greater
RJ-45 port:
Power Source
Standard Ethernet (RJ-45)
120 V AC, 60 Hz
Dimensions
Power Consumption
62MX196: Width: 57-1/16 inches (1,450 mm)
Height: 39-1/4 inches (997 mm)
226 W (average)
29 W in standby mode (using a CableCARD™)
25 W in standby mode (without a CableCARD™)
Depth: 18-3/4 inches (476 mm)
72MX196: Width: 65-13/16 inches (1,672 mm)
Height: 44-1/16 inches (1,119 mm)
Depth: 21-11/16 inches (551 mm)
Audio Power
15 W + 15 W
Weight
Speaker Type
62MX196: 106 lbs (48.1 kg)
72MX196: 127 lbs (57.6 kg)
Main: Four 4-3/4 inches (120 mm) round
Tweeter: Two 1 inche (25 mm) round
Operating conditions
Video/Audio Terminals
Temperature: 41ºF–95ºF (5ºC–35ºC)
Humidity: 20–80% (no moisture condition)
S-VIDEO INPUT:
Y: 1 V(p-p), 75 ohm, negative sync.
C: 0.286 V(p-p) (burst signal), 75 ohm
Supplied Accessories
• Remote control with two size “AA” alkaline batteries
• Dual-wand IR blaster cable
• Installation Guide
VIDEO/AUDIO INPUT:
VIDEO: 1 V(p-p), 75 ohm, negative sync.
AUDIO: 150 mV(rms) (30% modulation equivalent,
22 k ohm or greater)
ColorStream® (component video) HD INPUT:
VIDEO:Y: 1V(p-p), 75 ohm
• Operating Guide (this book)
• TV Guide On Screen™ Interactive Program Guide
Optional Stands
PR: 0.7 V(p-p), 75 ohm
PB: 0.7 V(p-p), 75 ohm
62MX196: ST 6296
72MX196: ST 7296
Suggested formats: 1080i, 480p, 480i, 720p
AUDIO: 150 mV(rms), 22 k ohm or greater
* Encrypted channels can be viewed on this TV using a
CableCARD.™ (- Installation Guide).
**E-EDID = Enhanced-Extended Display Identification
87
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 88 Tuesday, June 27, 2006 1:43 PM
Chapter 9: Appendix
(1) You must retain your original bill of sale or provide other proof of
purchase.
Limited United States Warranty
(2) All warranty servicing of this DLP® Television must be performed by
an Authorized TACP Service Station.
for DLP® Television Models
(3) The warranties from TACP are effective only if this DLP® Television is
purchased and operated in the Continental U.S.A. or Puerto Rico.
(4) Labor service charges for set installation, setup, adjustment of
customer controls, and installation or repair of antenna systems are
not covered by this warranty. Reception problems caused by
inadequate antenna systems, misaligned satellite dishes, cable
television distribution, VCRs, DVD players/recorders, personal
computer level IEEE 1394 devices, and any other connected signal
source device are your responsibility.
Toshiba America Consumer Products, L.L.C. (“TACP”) makes the
following limited warranties to original consumers in the United States.
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL
CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS DLP®
TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER
PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
DLP® TELEVISIONS PURCHASED IN THE U.S.A. AND USED
ANYWHERE OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT
LIMITATION, CANADA AND MEXICO, ARE NOT COVERED BY THESE
WARRANTIES.
(5) Warranties extend only to defects in materials or workmanship as
limited above, and do not extend to any DLP® Television or parts that
have been lost or discarded by you or to damage to the DLP®
Television or parts caused by fires, misuse, accident, Acts of God
(such as lightning or fluctuations in electric power), improper
installation, improper maintenance, or use in violation of instructions
furnished by TACP; use or malfunction through simultaneous use of
this DLP® Television and connected equipment; or to units that have
been modified or had the serial number removed, altered, defaced,
or rendered illegible.
DLP® TELEVISIONS PURCHASED ANYWHERE OUTSIDE OF THE
U.S.A., INCLUDING, WITHOUT LIMITATION, CANADA AND MEXICO,
AND USED IN THE U.S.A., ARE NOT COVERED BY THESE
WARRANTIES.
Limited One (1) Year Warranty on Parts and Labor
TACP warrants this DLP® Television and its parts against defects in
materials or workmanship for a period of one (1) year after the date of
original retail purchase. DURING THIS PERIOD, TACP WILL, AT TACP'S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR
LABOR. During this period, TACP Authorized Service Station personnel
will come to your home when warranty service is required. Depending on
the type of repair required, the service will either be performed in your
home or the DLP® Television will be taken to a TACP Authorized Service
Station for repair and returned to your home at no cost to you.
How to Obtain Warranty Service
If, after following all of the operating instructions in this manual and
reviewing the section entitled “Troubleshooting,” you find that service is
needed:
(1) To find the nearest TACP Authorized Service Station, visit TACP’s
Consumer Solution Center toll free at 1-800-631-3811.
(2) You must present your original bill of sale or other proof of purchase
to the TACP Authorized Service Station.
Limited One (1) Year Warranty on Lamp Unit
TACP warrants the original lamp unit contained in this DLP® Television
against defects in materials or workmanship for a period of one (1) year
after the date of original retail purchase. DURING THIS PERIOD, TACP
WILL, AT TACP'S OPTION, EXCHANGE A DEFECTIVE LAMP UNIT
WITH A NEW OR REFURBISHED LAMP UNIT WITHOUT CHARGE TO
YOU. LABOR CHARGES FOR LAMP UNIT REPLACEMENT ARE YOUR
RESPONSIBILITY AND ARE NOT COVERED UNDER THIS
WARRANTY. The lamp unit is a user-replaceable component.
For additional information, visit TACP's website:
ALL WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE
U.S.A., INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY
WARRANTIES IMPLIED BY THE LAW OF ANY STATE OF THE U.S.A.
AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES,
AGREEMENTS, AND SIMILAR OBLIGATIONS OF TACP WITH
RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO
EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST
PROFITS, BUSINESS INTERRUPTION, OR MODIFICATION OR
ERASURE OF RECORDED DATA CAUSED BY USE, MISUSE OR
INABILITY TO USE THIS DLP® TELEVISION).
Rental Units
The warranty for DLP® Television rental units begins on the date of the first
rental or thirty (30) days after the date of shipment to the rental firm,
whichever comes first.
Limited Warranty for Commercial Units
TACP warrants DLP® Televisions, including the lamp units contained
therein, that are sold and used for commercial purposes as follows: all
parts are warranted against defects in materials or workmanship for a
period of ninety (90) days after the date of original retail purchase.
DURING THIS PERIOD, TACP WILL, AT TACP'S OPTION, REPAIR OR
REPLACE A DEFECTIVE PART WITH A NEW OR REFURBISHED PART
WITHOUT CHARGE TO YOU.
No person, agent, distributor, dealer, or company is authorized to change,
modify, or extend the terms of these warranties in any manner whatsoever.
The time within which an action must be commenced to enforce any
obligation of TACP arising under the warranty or under any statute or law
of the United States or any state thereof is hereby limited to ninety (90)
days from the date you discover, or should have discovered, the defect.
This limitation does not apply to implied warranties arising under the law
of any state of the U.S.A.
Owner's Manual and Product Registration Card
Read this owner’s manual thoroughly before operating this DLP®
Television.
Complete and mail the enclosed product registration card or register your
possible. By registering your DLP® Television you will enable TACP to bring
you new products specifically designed to meet your needs and help us to
contact you in the unlikely event a safety notification is required under the
U.S. Consumer Product Safety Act. Failure to complete and return the
product registration card does not diminish your warranty rights.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE
TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT
ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED
WARRANTY, WHEN AN ACTION MAY BE BROUGHT, OR THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
TO YOU UNDER SUCH CIRCUMSTANCES.
05
88
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 89 Tuesday, June 27, 2006 1:43 PM
Chapter 9: Appendix
Your Responsibility
Limited Canada Warranty
THE ABOVE WARRANTIES ARE SUBJECT TO THE FOLLOWING
CONDITIONS:
for DLP® Television Models
(1) You must provide your bill of sale or other proof of purchase.
(2) All warranty servicing of this DLP® television must be performed by an
Authorized TCL Service Depot.
Toshiba of Canada Limited (“TCL”) makes the following limited warranties
to original consumers in Canada.
(3) These warranties from TCL are effective only if the DLP® television is
purchased in Canada from an authorized TCL dealer and operated in
Canada.
THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL
CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS DLP®
TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER
PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
PRODUCTS PURCHASED IN THE U.S.A. AND USED IN CANADA ARE
NOT COVERED BY THESE WARRANTIES.
(4) Labor charges for installation, setup, adjustment of customer
controls, and installation or repair of antenna systems are not covered
by these warranties. Reception problems caused by inadequate
antenna systems are your responsibility.
(5) Warranties extend only to defects in materials or workmanship as
limited above, and do not extend to any DLP® television or parts that
have been lost or discarded by you or to damage to the television or
parts caused by fires, misuse, accident, Acts of God (such as
lightning or fluctuations in electric power), improper installation,
improper maintenance, or use in violation of instructions furnished by
TCL; use or malfunction through simultaneous use of this product and
connected equipment; or to units that have been modified or had the
serial number removed, altered, defaced, or rendered illegible.
PRODUCTS PURCHASED IN CANADA AND USED IN THE U.S.A. ARE
NOT COVERED BY THESE WARRANTIES.
Limited One (1) Year Warranty on Parts and Labor*
TCL warrants this DLP® television and its parts against defects in
materials or workmanship for a period of one (1) year after the date of
original retail purchase. DURING THIS PERIOD, TCL WILL, AT TCL’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU FOR PARTS OR
LABOR. TCL Authorized Service Depot personnel will come to your home
when warranty service is required. Depending on the type of repair
required, either the service will be performed in your home or the set will
be taken to the TCL Authorized Service Depot for repair and returned to
your home at no cost to you. IN-HOME SERVICE ONLY APPLIES WITHIN
100 KILOMETERS OF AN AUTHORIZED TCL SERVICE DEPOT.
How to Obtain Warranty Services
If, after following all of the operating instructions in this manual and
checking the “Troubleshooting” section, you find that service is needed:
(1) To find the nearest TCL Authorized Service Depot, visit TCL’s web site
(2) Present your bill of sale or other proof of purchase to the Authorized
Service Depot.
Limited One (1) Year Warranty on Lamp Unit*
TCL warrants the lamp unit in this DLP® television against defects in
materials or workmanship for a period of one (1) year after the date of
original retail purchase. DURING THIS PERIOD, TCL WILL, AT TCL’S
OPTION, EXCHANGE A DEFECTIVE LAMP UNIT WITH A NEW OR
REFURBISHED LAMP UNIT WITHOUT CHARGE TO YOU. LABOR
CHARGES FOR LAMP UNIT REPLACEMENT ARE NOT COVERED
UNDER WARRANTY. The lamp unit is a user-replaceable component.
For additional information, visit TCL’s web site:
ALL WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCE OF
CANADA, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSLY LIMITED TO THE DURATION OF THE LIMITED
WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY
WARRANTIES IMPLIED BY THE LAW OF ANY PROVINCE OF CANADA
AS HEREBY LIMITED, THE FOREGOING WARRANTY IS EXCLUSIVE
AND IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES,
AGREEMENTS, AND SIMILAR OBLIGATIONS OF TCL WITH RESPECT
TO THE REPAIR OR REPLACEMENT OF ANY PARTS. IN NO EVENT
SHALL TCL BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS,
BUSINESS INTERRUPTION, OR MODIFICATION OR ERASURE OF
RECORDED DATA CAUSED BY USE, MISUSE, OR INABILITY TO USE
THIS PRODUCT).
Rental Units
The warranty for rental units, including the lamp units contained therein,
begins with the date of first rental or thirty (30) days from the date of
shipment to the rental firm, whichever comes first.
*Limited Warranty for Commercial Units
TCL warrants DLP® televisions, including the lamp units contained therein,
sold and used for commercial purposes as follows: all parts are warranted
against defects in materials or workmanship for a period of ninety (90)
days after the date of original purchase. DURING THIS PERIOD, TCL
WILL, AT TCL’S OPTION, REPAIR OR REPLACE A DEFECTIVE PART
WITH A NEW OR REFURBISHED PART WITHOUT CHARGE TO YOU.
ON-SITE SERVICE ONLY APPLIES WITHIN 100 KILOMETERS OF AN
AUTHORIZED TCL SERVICE DEPOT.
No person, agent, distributor, dealer, or company is authorized to change,
modify, or extend the terms of these warranties in any manner whatsoever.
The time within which action must be commenced to enforce any
obligation of TCL arising under this warranty or under any law of Canada
or of any province thereof is hereby limited to 90 days from the date you
discover, or should have discovered, the defect. This limitation does not
apply to implied warranties arising under the law of any province of
Canada.
Owner’s Manual and Product Registration
Read this owner’s manual thoroughly before operating this DLP®
television.
By registering your product you will enable TCL bring you new products
specifically designed to meet your needs and help us to contact you in the
unlikely event a safety notification is required under the U.S. Consumer
Product Safety Act. Failure to register your product does not diminish your
warranty rights.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY FROM
PROVINCE TO PROVINCE IN CANADA. SOME PROVINCES OF
CANADA DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN
IMPLIED WARRANTY, LIMITATIONS ON THE TIME WITHIN WHICH AN
ACTION MAY BE BROUGHT, OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES; THEREFORE, THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU
UNDER SUCH CIRCUMSTANCES.
89
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 90 Tuesday, June 27, 2006 1:43 PM
Chapter 9: Appendix
A copy of the GPL source code in this product may be obtained by
contacting Toshiba Consumer Solutions at (800)631-3811. There will be
a charge to cover the costs of providing the source code.
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS”
AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product
includes cryptographic software written by Eric Young
A copy of the LGPL source code in this product may be obtained by
contacting Toshiba Consumer Solutions at (800)631-3811. There will be
a charge to cover the costs of providing the source code.
USB Protocol Copyright © 2005 The NetBSD Foundation, Inc. All rights
reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
(1) Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
(3) Neither the name of The NetBSD Foundation nor the names of its
contributors may be used to endorse or promote products derived
from this software without specified prior written permission.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC.
AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
(eay@cryptsoft.com). This product includes software written by Tim
Hudson (tjh@cryptsoft.com).
Copyright © 1995-1998 Eric Young (eay@cryptsoft.com). All Rights
reserved. This package is an SSL implementation written by Eric Young
(eay@cryptsoft.com). The implementation was written so as to conform
with Netscapes SSL. This library is free for commercial and non-
commercial use so long as the following conditions are adhered to. The
following conditions apply to all code found in this distribution, be it the
RC4, RSA, Ihash, DES, etc., code; not just the SSL code. The SSL
documentation included with this distribution is covered by the same
copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young’s, and as such any Copyright notices in
the code are not to be removed. If this package is used in a product, Eric
Young should be given attribution as the author of the parts of the library
used. This can be in the form of a textual message at program startup
or in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:
(1) Redistributions of source code must retain the copyright notice, this
list of conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
(3) All advertising materials mentioning features or use of this software
must display the following acknowledgement: “This product includes
cryptographic software written by Eric Young (eay@cryptsoft.com).”
The word ‘cryptographic’ can be left out if the routines from the library
being used are not cryptographic related.
This product includes software developed by the OpenSSL Project for use
in the OpenSSL Toolkit (http://www.openssl.org).
This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com).
OpenSSL 0.9.7d Copyright © 1998-2000 the OpenSSL Project. All Rights
reserved. Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the following conditions
are met:
(4) If you include any Windows specific code (or derivative thereof) from
the apps directory (application code) you must include an
(1) Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
(3) All advertising materials mentioning features or use of this software
must display the following acknowledgement: This product includes
software developed by the OpenSSL Project for use in the OpenSSL
Toolkit (http://openssl.org).
(4) The names “OpenSSL Toolkit” and “Open SSL Project” must not be
used to endorse or promote products derived from this software
without prior written permission. For written permission, please
contact openssl-core@openssl.org.
(5) Products derived from this software may not be called “OpenSSL” nor
may “Open SSL” appear in their names without prior written
permission of the OpenSSL Project.
(6) Redistributions of any form whatsoever must retain the following
acknowledgement: “This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http://
www.openssl.org).”
acknowledgement: “This product includes software written by Tim
Hudson (tjh@cryptosoft.com).”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE. The license and distribution terms for any publicly available
version or derivative of this code cannot be changed, i.e. this code cannot
simply be copied and put under another distribution license (including the
GNU Public License).
90
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 91 Tuesday, June 27, 2006 1:43 PM
Index
A
H
Q
Account.......................................... 70
Antenna input configuration ............ 25
Audio player................................... 69
Audio quality adjustments............... 45
Auto aspect.................................... 39
Auto power off................................ 54
HDMI™ audio mode ........................29
Home file server setup ....................65
Quick Restart™................................. 30
R
I
RECALL button...............................54
Remote control
ID...................................................74
INPUT button..................................32
Input lock feature............................50
Internet service provider..................60
Battery installation....................11
Effective range.........................11
Learning about the buttons .......12
Operational feature...................17
Volume lock feature..................17
B
Back of the TV.................................. 9
Blocking channels .......................... 49
J
JPEG .............................................66
S
C
SAP sound .....................................45
Scroll settings .................................38
Selecting Menu Language...............25
Setting up file sharing......................62
Side panel control .............................8
Sleep timer .....................................52
Slide show......................................68
Speaker On/Off...............................46
Specifications .................................87
StableSound®................................... 46
Stereo sound ..................................45
SurfLock™ ........................................ 36
System status .................................31
L
C (CLOSED). CAPTION button....... 44
CableCARD™................................... 29
CableClear® ..................................... 55
CH RTN button............................... 36
CH U u buttons............................ 35
Channel Browser Setup.................. 34
Channel Browser™........................... 33
Channel Number buttons................ 35
Labeling video input........................32
Lamp mode ....................................57
Lamp unit replacement....................84
Language selection.........................25
Last mode memory feature .............54
LED indications...............................83
LOCKS menu
Channels, blocking...................49
Enable rating blocking..............48
New PIN code..........................47
Panel lock................................51
Unlocking programs temporarily..50
Video inputs, locking ................50
Channel programming
Automatic programming........... 26
Manually adding and deleting... 27
Cinema mode................................. 39
Closed captions.............................. 43
Color Management......................... 58
Color temperature .......................... 56
ColorStream HD audio.................... 28
Locks menu....................................47
T
TheaterWide® picture size...............37
THINC button..................................12
THINC™ system..............................10
Time and date setting......................28
Troubleshooting ..............................79
TV GUIDE button............................12
M
Menu system..................................22
MODE SELECT........................12, 16
MP3 .........................................66, 69
MPEG noise reduction ....................56
MTS feature ...................................45
MUTE button ..................................44
D
Defaults, reset TV factory ............... 31
Device codes table ......................... 18
Digital audio selector ...................... 44
Digital signal meter......................... 30
Dolby Virtual/SRS TruSurround....... 59
Double-window POP feature........... 40
Dynamic contrast............................ 55
V
V-Chip blocking (Locks menu).........47
Vertical Edge Enhancer...................57
Video input label .............................32
N
Network address, setup ..................60
O
E
W
Warranty
On/Off timer....................................52
Optical audio output format .............46
E-mail account setup...................... 70
E-mail recording............................. 60
E-mail scheduling........................... 70
Canada....................................89
U.S..........................................88
P
WOW:SRS 3D ................................59
WOW:SRS Focus ...........................59
WOW:SRS TruBass........................59
Password .......................................74
PC settings.....................................53
Picture adjustment..........................42
Picture mode ..................................42
Picture quality.................................42
Picture scroll...................................38
Picture size selection ......................37
Picture Viewer ..........................66, 67
POP button.....................................40
POWER button.................................8
F
Features, TV .................................... 6
FREEZE ........................................ 41
Front of the TV ................................. 8
G
Game Mode feature........................ 58
GameTimer™ ................................... 51
91
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 92 Tuesday, June 27, 2006 1:43 PM
Notes
92
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 93 Tuesday, June 27, 2006 1:43 PM
Notes
93
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 94 Tuesday, June 27, 2006 1:43 PM
Notes
94
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 95 Tuesday, June 27, 2006 1:43 PM
Notes
95
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
MX196_EN.book Page 96 Tuesday, June 27, 2006 1:43 PM
Corporate Headquarters: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A.
NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A.
HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400
SERVICE CENTERS:
TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470- 5400
MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA – TEL: (514) 390-7766
VANCOUVER: 13551 COMMERCE PARKWAY, SUITE 110, RICHMOND, B.C., V6V 2L1, CANADA – TEL: (604) 303-2500
MANUFACTURED BY
CableClear, Cinema Series, ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C.
Channel Browser, GameTimer, SurfLock, THINC, and Quick Restart are trademarks of Toshiba America Consumer Products, L.L.C.
Digital Light Processing®, DLP® and the DLP® medallion are registered trademarks of Texas Instruments.
PRINTED IN USA
(06-07)
MX196 (E/F) Web 213:276
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Tektronix Caulking Gun TDS420A User Manual
Texas Instruments Telephone TCM4300 User Manual
Thule Automobile Accessories 822 91822 User Manual
Toshiba Computer Drive SD M1712 User Manual
Trimble Outdoors Radar Detector HV101 User Manual
Tripp Lite Computer Hardware B132 004 RB User Manual
True Manufacturing Company Freezer GDIM 26 User Manual
UTStarcom Cell Phone CDM89215 User Manual
VTech Telephone CS6129 User Manual
Weber Gas Grill 38008 User Manual