DIGITAL PLAIN PAPER COPIER
OPERATOR’S MANUAL FOR COPYING FUNCTION
Networking Documents.
Download from Www.Somanuals.com. All Manuals Search And Download.
mmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm
For users in the USA
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user’s authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING:
Changes or modification mode to this equipment, not expressly approved by Toshiba TEC or parties
authorized by Toshiba TEC could void the user's authority to operate the equipment.
m
m m m m m m m m m m
m m m m m m m m m m m m m m m m m m m m m m m m m m
Shielded cables must be used with this equipment to maintain compliance with
FCC regulations.
Notice for Users in U.S A.
Installed I/F Board (For Printer Standard Model)
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Model Number:
AR-PG2 (I/F Board)
Responsible Party: Toshiba America Business Solutions, Inc.
2 Musick, Irvine, California 92618, U.S.A.
Tel: 949-462-6000
AR-PG2
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
This product utilizes tin-lead solder, and a fluorescent lamp containing a small
amount of mercury.
Disposal of these materials may be regulated due to environmental
considerations.
For disposal or recycling information, please contact your local authorities or the
2
Download from Www.Somanuals.com. All Manuals Search And Download.
User safety
This Toshiba digital plain paper copier does not produce laser radiation hazardous to the
user. It is certified as a Class 1 laser product under the U.S.Department of Health and
Human Services (DHHS) Radiation Performance Standard according to the Radiation
Control Health and Safety Act of 1968.
Protective housing and external covers completely confine the laser light emitted inside
the plain paper copier. The laser beam cannot escape from the machine during any
phase of user operation.
Regulations implemented on August 2, 1976 by the Bureau of Radiological Health (BRH)
of the U.S.Food and Drug Administration apply to laser products manufactured from
August 1, 1976. Laser products marketed in the United States must comply with these
regulations.
CAUTION : Using controls or adjustments or performing procedures, other than those
specified herein may result in hazardous radiation exposure.
Ozone information
After a suitable place has been selected for the installation, please do not change it. Avoid
excessive heat dust vibration and direct sunlight. Also, provide proper ventilation as the
copier emits a small amount of ozone.
A small amount of ozone is produced within the unit during operation. The
emission level is insufficient to cause any health hazard.
Note:
The present recommended long term exposure limit for ozone is 0.1ppm (0.2mg/m3)
calculated as an 8hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it
is advisable to place the unit in a ventilated area.
Machine noise information
Ordinance 3. GSGV, January 18, 1991: The maximum sound pressure level is equal or
less than 70 dB(A) according to EN27779.
For user in the Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
For user in the Europe
1. Do not touch the connector terminal when disconnecting the cables of peripheral
equipment.
2. Before opening any covers or removing any units from the copier, discharge the static
electricity from your body by touching a metal part of the copier.
This product is carrying the CE-Mark in accordance with the related European Directives.
Responsible for CE-marking is TOSHIBA TEC GERMANY IMAGING SYSTEMS GmbH,
Carl-Schurz-Str.7, 41460 Neuss, Germany.
e-mail : [email protected].
3
Download from Www.Somanuals.com. All Manuals Search And Download.
VAROITUS!
LAITTEEN KÄYTTÄMINEN
MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA
TAVALLA SAATTAA ALTISTAA
KÄYTTÄJÄN
CLASS 1 LASER PRODUCT
LASER KLASSE 1
TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE
NÄKYMÄTTÖMÄLLE
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
LASERSÄTEILYLLE.
VARNING
OM APPARATEN ANVÄNDS PÅ
ANNAT SÄTT ÄN I DENNA
BRUKSANVISNING
SPECIFICERATS, KAN
ANVÄNDAREN UTSÄTTAS FÖR
OSYNLIG LASERSTRÅLNING,
SOM ÖVERSKRIDER GRÄNSEN
FÖR LASERKLASS 1.
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES.
ADVERSEL UNNGÅ EKSPONERING FOR STRÅLEN.
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.
CAUTION
AVOID EXPOSURE TO BEAM.
UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR
VARNING
VORSICHT
ADVARSEL
SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AUSSETZEN.
URKOPPLADE. STRÅLEN ÄR FARLIG. BETRAKTA EJ STRÅLEN.
Laserstrahl
USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER
UDE AF FUNKTION. UNDGA UDSAETTELSE FOR STRÅLING.
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ
VARO! LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
Caution
This product contains a low
power laser device.
To ensure continued safety
do not remove any cover or
attempt to gain access to the
inside of the product. Refer
all servicing to qualified
personnel.
CLASS 1
LASER PRODUCT
LASER KLASSE 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
The CE mark logo label is affixed on an equipment in case that the directives described in the above
sentence are applicable to the product. (This sentence is not applicable in any country where the above
directives are not required.)
In some areas, the “POWER” switch positions are marked “I ” and “O” on the copier instead of
“ON” and “OFF”. The symbol “O” denotes the copier is not completely de-energized but in a
stand-by condition at this “POWER” switch position.
If your copier is so marked, please read “I ” for “ON” and “O” for “OFF”.
Caution!
For a complete electrical disconnection, pull out the main plug.The socket-outlet shall be
installed near the equipment and shall be easily accessible.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
Caution label on the unit
The label in the fusing area of the unit indicates the following:
: Caution, risk of danger
: Caution, hot surface
Cautions on using
Follow the cautions below when using this unit.
Warning:
•
•
•
The fusing area is hot. Exercise care in this area when removing misfed paper.
Do not look directly at the light source. Doing so may damage your eyes.
Do not switch the unit rapidly on and off. After turning the unit off, wait 10 to 15 seconds
before turning it back on.
•
Unit power must be turned off before installing any supplies.
Caution:
•
•
•
Place the unit on a firm, level surface.
Do not install the unit in a humid or dusty location.
When the unit is not used for a long time, for example for consecutive holidays, turn the
power switch off and remove the power cord from the outlet.
When moving the unit, be sure to turn the power switch off and remove the power cord
from the outlet.
Do not cover the unit with a dust cover, cloth or plastic film while the power is on. Doing
so may prevent heat radiation, damaging the unit.
•
•
•
Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
•
•
The socket outlet should be installed near the equipment and be easily accessible.
The power plug should be unplugged from the outlet once a year or more often to clean
the area between its edges.
If dust collects in the power plug area, humidity or the like may cause the insulation to
deteriorate and a fire may well result.
•
Do not throw toner or toner cartridge into fire. Toner may scatter and cause a burn.
Important points when selecting an installation site
Do not install your unit in areas that are:
•
•
•
•
damp, humid, or very dusty
exposed to direct sunlight
poorly ventilated
subject to extreme temperature or humidity changes, e.g., near an air conditioner or
heater.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Be sure to connect the power cord only to a power outlet that meets the specified voltage and current
requirements. Also make certain the outlet is properly grounded.-
Connect the unit to a power outlet which is not used for other electric appliances. If a lighting
fixture is connected to the same outlet, the light may flicker.
Be sure to allow the required space around the machine for servicing
and proper ventilation.
20cm
(8")
10cm
(4")
10cm
(4")
Cautions on handling
Be careful in handling the unit as follows to maintain the performance of this unit.
Do not drop the unit, subject it to shock or strike it against any object.
Store spare toner cartridges in a cool dry place without removing from the package before use.
If they are exposed to direct sunlight or excessive heat, poor copies may result.
Do not touch the photoconductive drum (green portion).
Scratches or smudges on the drum will cause dirty copies.
•
•
Cautions on laser
Wave length
770 nm – 795 nm
11.82 µs / 7 mm
Pulse times
Output power
0.17 mW +/- 0.01 mW
Proper storage for supplies
Store the supplies (paper and toner cartridges) in a location that is:
•
•
•
clean and dry
at a stable temperature
not exposed to direct sunlight.
Store paper in the wrapper and lying flat.
Paper stored out of the wrapper or in packages standing on end may curl or get damp,
resulting in paper misfeeds.
•
Trademark acknowledgements
•
Microsoft and Windows are trademarks of Microsoft Corporation in the U.S.A. and other
countries.
•
•
•
IBM and PC/AT are trademarks of International Business Machines Corporation.
Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
All other trademarks and copyrights are the property of their respective owners.
As an ENERGY STAR® Partner, TOSHIBA has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
Safety precautions:This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10
and 1040.11 of the CDRH standards. This means that the unit does not produce hazardous laser radiation.
For your safety, observe the precautions below.
• Do not remove the cabinet, operation panel or any other covers.
• The unit’s exterior covers contain several safety interlock switches.
Do not bypass any safety interlock by inserting wedges or other items into switch slots.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
INTRODUCTION.....................................................................................................1-1
USING THE MANUAL ............................................................................................. 1-2
PART NAMES ..........................................................................................................1-3
OPERATION PANEL ...............................................................................................1-4
LOADING PAPER...................................................................................................2-1
PAPER .....................................................................................................................2-2
LOADING THE PAPER TRAY ................................................................................. 2-4
BYPASS FEED (including special paper) ................................................................ 2-6
MAKING COPIES ...................................................................................................3-1
COPY FLOW ...........................................................................................................3-2
CONNECTING THE POWER CORD .....................................................................3-3
ORIGINAL PLACEMENT ........................................................................................3-5
SET THE COPY QUANTITY ................................................................................... 3-6
EXPOSURE ADJUSTMENT/PHOTO COPYING...................................................3-6
REDUCTION/ENLARGEMENT/ZOOM ..................................................................3-8
SELECTING THE TRAY ..........................................................................................3-9
SPECIAL FUNCTIONS...........................................................................................4-1
DESCRIPTION OF SPECIAL FUNCTIONS...........................................................4-2
TONER SAVE MODE.............................................................................................. 4-2
USER PROGRAMS ................................................................................................4-3
DISPLAYING TOTAL NUMBER OF COPIES.......................................................... 4-4
MAINTENANCE ......................................................................................................5-1
TONER CARTRIDGE REPLACEMENT .................................................................5-2
CLEANING THE UNIT............................................................................................. 5-5
TROUBLESHOOTING THE UNIT ..........................................................................6-1
TROUBLESHOOTING ............................................................................................6-2
STATUS INDICATORS.............................................................................................6-3
MISFEED REMOVAL ..............................................................................................6-4
DEVELOPER REQUIRED ......................................................................................6-7
MAINTENANCE REQUIRED..................................................................................6-7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE SOFTWARE .............................................................................7-1
SOFTWARE FOR THE TOSHIBA PERSONAL MFP SERIES............................... 7-2
HARDWARE AND SOFTWARE REQUIREMENTS ...............................................7-3
BEFORE INSTALLATION ........................................................................................7-3
INSTALLING THE SOFTWARE............................................................................... 7-5
INDICATORS ON THE OPERATION PANEL ....................................................... 7-15
USING THE PRINTER MODE .............................................................................. 7-16
USING THE SCANNER MODE ............................................................................ 7-18
HOW TO USE THE ONLINE MANUAL ................................................................. 7-26
USING OTHER INSTALLED DRIVERS................................................................ 7-28
CONNECTING THE INTERFACE CABLE ...........................................................7-29
APPENDIX ..............................................................................................................8-1
SPECIFICATIONS ...................................................................................................8-2
OPTIONAL EQUIPMENT........................................................................................8-4
INDEX ......................................................................................................................8-9
SOFTWARE LICENSE ..........................................................................................8-11
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
This chapter provides basic information for using the unit.
USING THE MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
PART NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
OPERATION PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE MANUAL
The operator’s manual contains explanations of how to operate the unit, important considerations, and
maintenance procedures. To get the most out of the unit, please read the operator’s manual. Please keep
the operator’s manuals in a suitable location that will allow for convenient future reference.
Conventions used in this manual
In this manual, the following icons are used to provide the user with information pertinent to the use of the
unit.
Warns the user that injury to the user or damage to the copier may result if the contents
of the warning are not properly followed.
Cautions the user that damage to the copier or one of its components may result if the
contents of the caution are not properly followed.
Notes provide information relevant to the copier regarding specifications, functions,
performance, operation and such, that may be useful to the user.
Indicates a letter displayed in the display.
AB series (metric) and inch series references
When references are made to paper sizes and weights, the inch series values are quoted in brackets.
For example:
52 to 130 g/m2 (14 lbs. to 34.5 lbs.)
A4 (8-1/2" x 11")
INTRODUCTION
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
PART NAMES
1
2
5
6
9
10
3
4
11
12
13
7
8
14
5
3
15
16
Photoconductive drum
Toner cartridge
ቢ Original table
ቭ Power switch
ባ Operation panel
ቤ Front cover
ብ Paper tray
ቮ Handle
ቯ Power cord socket
ተ Fusing unit release lever
ቱ Transfer charger
ቲ Charger cleaner
ቦ Side cover
ቧ Side cover open button
ቨ Multi-bypass tray
ቩ Bypass tray guides
ቪ Paper output tray
ቫ Paper output tray extension
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION PANEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
ቭ ZOOM keys and indicator
ቢ ONLINE key and indicator (p. 7-15)
Use to select any reduction or enlargement copy
ratio from 25% to 400% in 1% increments.
(p. 3-8)
Lights up when the unit is used as a printer and
scanner.For description of the ON LINE indicator,
see “INDICATORS ONTHE OPERATION PANEL”
(p. 7-15)
ቮ Copy quantity keys
•
Use to select the desired copy quantity (1 to
ባ SCANNER key and indicator (p. 7-15, 7-22)
99). (p. 3-6)
•
Use to make user program entries. (p. 4-3)
ቤ Copy ratio selector key and indicators
Use to sequentially select preset reduction/
enlargement copy ratios. Selected copy ratio is
shown by a lit indicator. (p. 3-8)
ቯ Tray select key
Use to select a paper feed station (paper tray 1,
paper tray 2 or bypass tray). (p. 3-9)
ብ Copy ratio display (%) key (p. 3-8)
ተ Paper feed location indicators
ቦ Display
Light up to show the selected paper feed station.
Displays the specified copy quantity, zoom copy
ratio, user program code, and error code.
ቱ Light and dark keys and indicators
Use to adjust the MANUAL or PHOTO exposure
level. Selected exposure level is shown by a lit
indicator. (p. 3-6) Use to start and terminate user
program setting. (p. 4-3)
ቧ Alarm indicators
Developer replacement required indicator
(p. 6-7)
Misfeed indicator (p. 6-4)
ቲ Clear key
•
Press to clear the display, or press during a
copy run to terminate copying. (p. 3-6)
Press and hold down during standby to
display the total number of copies made to
date. (p. 4-4)
Toner cartridge replacement
required indicator (p. 5-2)
•
Maintenance indicator (p. 6-7)
ቨ ADF indicator (p. 8-5)
ታ Start key and indicator
ቩ ADF misfeed indicator (p. 8-6)
•
•
•
Copying is possible when the indicator is on.
Press to start copying.
Use to set a user program. (p. 4-3)
ቪ Exposure mode selector key and indicators
Use to sequentially select the exposure modes:
AUTO, MANUAL or PHOTO. Selected mode is
shown by a lit indicator. (p. 3-7)
ቫ Power save indicator
Lights up when the unit is in a power save mode.
(p. 4-21, 4-22)
INTRODUCTION
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING PAPER
Follow the steps below to load paper into the tray.
PAPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
LOADING THE PAPER TRAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
BYPASS FEED (including special paper) . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
PAPER
For best results, use only paper recommended by TOSHIBA.
Type of paper feeding Type of media
Size
Weight
Paper tray
Standard paper
A4 (210mm x 297mm)
A5 (148.5mm x 210mm)
B5 (182mm x 257mm)
Letter (8-1/2" x 11")
56g/m2 to 80g/m2
(15 lbs. to 21 lbs.)
Legal (8-1/2" x 14")
Invoice (5-1/2" x 8-1/2")
Bypass tray
Standard paper
and thick paper
A4 (210mm x 297mm)
A5 (148.5mm x 210mm)
A6 (105mm x 148.5mm)
B5 (182mm x 257mm)
B6 (128mm x 182mm)
Letter (8-1/2" x 11")**
Legal (8-1/2" x 14")
52g/m2 to 128g/m2
(14 lbs. to 34.5 lbs.)**
Invoice (5-1/2" x 8-1/2")
Special
media
A4 (210mm x 297mm)
Letter (8-1/2" x 11")
Transparency
film
International DL
(110mm x 220mm)
International C5
Envelope*
(162mm x 229mm)
Commercial 10
(4-1/8" X 9-1/2")
Monarch(3-7/8" X 7-1/2")
*
Do not use non-standard envelopes, and envelopes that have metal clasps, plastic snappers, string
closures, windows, linings, self-adhesive, patches or synthetic materials. Do not use envelopes that
are filled with air or envelopes that have labels or stamps attached. These will cause physical damage
to the unit.
** For paper weighing from 104g/m2 to 128g/m2 (28 lbs. to 34.5 lbs.), A4 (8-1/2" x 11") is the maximum size
that can be fed through the bypass tray.
•
Special papers such as transparency film, labels and envelope must be fed one sheet at a time through
the bypass tray.
LOADING PAPER
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Be sure to use only genuine TOSHIBA parts and supplies. For best copying results, be sure
to use only TOSHIBA Genuine Supplies which are designed, engineered, and tested to
maximize the life and performance of TOSHIBA copiers. Look for the Genuine Supplies label
on the toner package.
Proper storage
1. Store the supplies in a location that is:
•
•
•
clean and dry,
at a stable temperature,
not exposed to direct sunlight.
2. Store copy paper in the wrapper and lying flat.
•
Paper stored out of the wrapper or in packages standing on end may curl or get damp,
resulting in paper misfeeds.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING THE PAPER TRAY
Raise the handle of the paper tray and pull the paper tray out
until it stops.
1
Adjust the paper guides on the paper tray to the copy paper width and length. Squeeze the
lever of paper guide
and slide the guide to match with the width of the paper. Move paper
A
2
3
guide
to the appropriate slot as marked on the tray.
B
Paper
Paper
guide A
guide B
Fan the paper and insert it into the tray. Make sure the edges go under the corner hooks.
Do not load paper above the maximum height line (
paper misfeed.
). Exceeding the line will cause a
LOADING PAPER
Download from Www.Somanuals.com. All Manuals Search And Download.
2-4
Gently push the paper tray back into the unit.
4
•
After loading paper, to cancel the blinking
without restarting copying, press the clear
) indicator will light up.
(
) key. The in the display will go out and the start (
•
•
•
Be sure that paper is free of rips, dust, wrinkles, and curled or bent edges.
Make sure all the paper in the stack is the same size and type.
When loading paper, ensure there is no space between the paper and the guide, and
check if the guide is not set too narrow causing the paper to bend. Loading paper in
these ways will result in document skew or a paper jam.
•
•
When not using the unit for an extended period, remove all paper from the paper tray and
store it in a dry place. If paper is left in the unit for an extended period, the paper will
absorb moisture from the air, resulting in paper jams.
When adding new paper to the paper tray, remove the old paper already contained in the
tray. Placing new paper on top of the paper already contained in the tray may result in
feeding two sheets at one time.
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
BYPASS FEED (including special paper)
The bypass tray automatically feeds up to 50 sheets of standard copy paper and also feeds special papers
such as transparency film and labels one sheet at a time. Copy paper measuring from A6 to A4 (3-1/2" x 5-
1/2" to 8-1/2" x 14") and in the weight range of 52 to 128g/m2 (28 to 34.5 lbs.) can be used in this tray. (For
paper weighing from 104 to 128g/m2 (28 to 34.5 Ibs.), A4 (8-1/2" X 11") is the maximum size.)
Place the original face down on the original table. Align it with the original scale and close the
original cover.
1
The original image must be smaller than the paper or media for copying.
If the original image is bigger than the paper or media, this may cause smudges on the
edges of the copies.
Open the bypass tray and extend the tray.
2
To close the bypass tray, perform step 1 and then
step 2 in the illustration and push the round
projections at the right of the tray until the tray
clicks into place.
LOADING PAPER
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the paper guides to the copy paper width. Insert the copy paper (print face down) all the
way into the bypass tray.
3
4
•
•
•
Paper must be fed narrow side into the feed slot.
Transparency film, labels, and other special purpose papers must be fed individually.
When copying onto transparency film, remove each copy promptly.
Do not let copies stack up.
•
When loading an envelope, make sure that it is straight and flat.
Print face
Press the tray select (
standard copy paper. Press the start (
) key to select the bypass tray. Set the number of copies if using
) key.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING PAPER
Download from Www.Somanuals.com. All Manuals Search And Download.
2-8
Making Copies
This chapter explains basic and other copying functions.
The unit is equipped with a one-page memory buffer. This memory allows the unit to scan an original once
only and make up to 99 copies. This feature improves workflow, reduces operation noise from the copier,
and provides higher reliability by reducing wear and tear on the scanning mechanism.
If the unit does not function properly during use, or if a function cannot be used, see
“TROUBLESHOOTING THE UNIT (p. 2-6)”
COPY FLOW ...........................................................................................................................3-2
CONNECTING THE POWER CORD .....................................................................................3-3
ORIGINAL PLACEMENT ........................................................................................................3-5
SET THE COPY QUANTITY ...................................................................................................3-6
EXPOSURE ADJUSTMENT/PHOTO COPYING ...................................................................3-6
REDUCTION/ENLARGEMENT/ZOOM ..................................................................................3-8
SELECTING THE TRAY ..........................................................................................................3-9
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
COPY FLOW
MAKING COPIES
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE POWER CORD
If you use the unit in a country other than the country where the unit was purchased, you will
need to make sure that your local power supply is compatible with your model. If you plug
the unit into an incompatible power supply, irreparable damage to the unit will result.
Ensure that the power switch of the unit is in the OFF position. Insert the attached power cord
into the power cord socket at the rear of the unit.
1
Plug the other end of the power cord into the nearest outlet.
2
Only insert the power cord into a properly grounded wall socket. Do not use extension cords
or power strips.
Power on
Ensure that the power switch of the unit is in the OFF position.
Plug the other end of the power cord into the nearest outlet.
Turn the power switch on the left side of the unit to the “ON”
position. The start (
) indicator will light up and other
indicators which show the initial settings of the operation panel
will also light up to indicate the ready condition. For the initial
settings, see the “Initial settings of operation panel” described
on the next page.
•
•
The unit will enter a power save mode once the set time has elapsed without any unit
operation. The settings of the power save modes can be modified. See “USER
PROGTRAMS” (p. 4-3)
The unit will return to the initial settings a preset amount of time after the end of copy or
scanning job. The preset amount of time (auto clear time) can be changed. See “USER
PROGTRAMS” (p. 4-3)
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
About the scan head
The scan head lamp remains on constantly when the unit is in the ready condition
(when the start (
) indicator is illuminated).
The unit adjusts the scan head lamp periodically to maintain copying quality. At this time, the scan head
moves automatically. This is normal and does not indicate unit trouble.
Initial settings of operation panel
When the unit power is on, the operation panel will revert to the initial settings when the time set with the
“Auto clear time” setting (p. 4-2) elapses after a copy or scanner job is finished, or when the clear (
is pressed twice.
) key
The initial settings of the operation panel are shown below.
When copying is begun in this state, the settings in the following table are used.
Copy quantity
Exposure adjustment
Zoom
1 copy
AUTO
100%
Power off methods
If not used for a certain period of time, the unit will automatically enter auto power shut-off mode (p. 4-3) in
order to minimise power consumption. In cases where the machine will not be used for a long time, turn off
the power switch and remove the power cord from the outlet.
MAKING COPIES
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
ORIGINAL PLACEMENT
•
•
The original table can read up to A4 (8-1/2" x 14") original.
Image loss 4mm (5/32") can occur at the leading and trailing edges of the copies. Also
image loss 4.5mm (11/64") in total can occur along the other edges of the copies.
When copying a book or an original which has been folded or a crumpled original,
press down the original cover lightly. If the original cover is not securely closed, the
copies may be striped or blurred.
•
Open the original cover, and place the original.
1
2
Place an original face down on the original table. Align it with the original scale and the
centring ( )mark. Gently close the original cover.
Original scale
mark
Setting a large original
The original cover can be removed to allow copying of bulky objects.
Simply lift the original cover straight up.
1
To reattach the original cover, reverse the above procedure.
2
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SET THE COPY QUANTITY
Set the number of copies using the two copy quantity (
table.
,
) keys when copying from the original
•
•
Press the clear (
) key to clear an entry if a mistake is made.
A single copy can be made with the initial setting, i.e., when “1” is displayed.
•
Press the
be carried out while you press and hold down the
Also, if the key is pressed while 99 appears, the copy quantity becomes 0
and the count from 1 to 99 is restarted.
key to count up the copy quantity from 1 to 99. (A fast countup will
key.)
•
•
If the
key is pressed, the copy quantity becomes 0 and is counted down from
99 to 1. (A fast countdown will be carried out while you press and hold down the
key.)
When the
key is pressed during copying, the number of copies is displayed.
EXPOSURE ADJUSTMENT/PHOTO COPYING
Exposure adjustment
Copy density adjustment is not required for most originals in the automatic exposure mode. To adjust the
copy density manually or to copy photographs, the exposure level can be adjusted in five steps manually.
The copy resolution used for AUTO and MANUAL (
) mode can be changed. (p. 4-3)
Press the exposure mode selector key to select the MANUAL
) mode or PHOTO ( ) mode.
(
1
2
Use the light (
) and dark (
) keys to adjust the exposure level.
If exposure level 2 is selected, the two left-handmost indicators for that
level will light up simultaneously. Also, if level 4 is selected, the two
right-handmost indicators for that level will light up simultaneously.
MAKING COPIES
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6
Automatic exposure adjustment
This automatic exposure level will remain in effect until you change it again by this
procedure.
The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from
the original table.
Press the exposure mode selector key to select the PHOTO (
mode.
)
1
2
3
4
Press and hold down the exposure mode selector key for approximately
5 seconds. The PHOTO ( ) indicator will go out and the AUTO
indicator will begin to blink. One or two light and dark indicators
corresponding to the automatic exposure level which has been selected
will light up.
Press the light (
) or dark (
) key to lighten or darken the
automatic exposure level as desired. If exposure level 2 is selected,
the two left-handmost indicators for that level will light up simultaneously.
Also, if level 4 is selected, the two right-handmost indicators for that
level will light up simultaneously.
Press the exposure selector key. The AUTO indicator will stop blinking and light up steadily.
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
REDUCTION/ENLARGEMENT/ZOOM
Three preset reduction ratios and two enlargement ratios can be selected. The zoom function enables
copy ratio selection from 25% to 400% in 1% increments.
Set the original and check the paper size.
1
2
Use the copy ratio selector key and/or ZOOM (
ratio.
,
) keys to select the desired copy
•
•
To verify a zoom setting without changing the zoom ratio, press and hold down the copy
ratio display key. When the key is released, the display will return to the copy quantity
display.
To reset the ratio to 100%, press the copy ratio selector key repeatedly until the 100%
indicator lights up.
Set the reduction/enlargement ratio.
3
To decrease or increase the zoom ratio rapidly, press and hold down the ZOOM (
) or
(
) key. However the value will stop at the preset reduction or enlargement ratios. To
move beyond these ratios, release the key and then press and hold it down again.
To select a preset copy ratio:
Preset reduction and enlargement ratios are: 25%, 70%, 86%, 141%, and 400%
(Inch series: 25%, 64%, 78%, 129%, and 400%).
To select a zoom ratio:
When a ZOOM (
) or (
) key is pressed, the ZOOM indicator will light up
and the zoom ratio will be displayed in the display.
MAKING COPIES
Download from Www.Somanuals.com. All Manuals Search And Download.
3-8
SELECTING THE TRAY
Press the tray select (
) key.
Each time you press the tray select (
by the paper feed location indicator changes in the following order:
paper tray 1, paper tray 2, bypass tray.
) key, the location indicated
1
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAKING COPIES
Download from Www.Somanuals.com. All Manuals Search And Download.
3-10
Special Functions
This chapter describes the special functions of this unit. Use these functions as needed.
DESCRIPTION OF SPECIAL FUNCTIONS ...........................................................................4-2
TONER SAVE MODE..............................................................................................................4-2
USER PROGRAMS ................................................................................................................4-3
DISPLAYING TOTAL NUMBER OF COPIES .........................................................................4-4
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION OF SPECIAL FUNCTIONS
Toner save mode (p. 4-2)
Reduces toner consumption by approximately 10%.
Power save modes (p. 4-3)
The unit has two power save modes of operation: preheat mode and auto power shut-off mode.
Preheat mode
When the unit enters the preheat mode, the power save (
) indicator will light up and other
indicators will remain on or off as before. In this condition, the fuser in the unit is maintained at a
lower heat level, thereby saving power. To copy from the preheat mode, make desired copier
selections and press the start (
) key using the normal copying procedure.
Auto power shut-off mode
When the unit enters the auto power shut-off mode, the power save ( ) indicator will light up and
other indicators except the ONLINE indicator will go out. The auto power shut-off mode saves more
power than the preheat mode but requires a longer time before starting copying. To copy from the
auto power shut-off mode, press the start (
) key. Then make desired copier selections and
press the start (
) key using the normal copying procedure.
Auto clear (p. 4-3)
The unit returns to the initial settings a preset amount of time after the end of copy, or scanner job. This
preset amount of time (auto clear time) can be changed.
Resolution of AUTO & MANUAL mode (p. 4-3)
You can set the copy resolution used for AUTO and MANUAL (
) exposure mode.
TONER SAVE MODE
Press the exposure mode selector key to select the
MANUAL (
) mode.
1
SPECIAL FUNCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2
Press and hold down the exposure mode selector key for approximately
5 seconds.The MANUAL ( ) indicator will go out and the PHOTO
) indicator will begin to blink.The light and dark indicator marked
“5” will light up, indicating the standard toner mode is active.
2
(
To enter the toner save mode, press the light (
dark indicator marked “1” will light up, indicating the toner save mode is
selected.
) key. The light and
3
4
Press the exposure mode selector key.The PHOTO (
) indicator will stop blinking and light
up steadily. The light and dark indicator marked “3” will light up. The toner save mode is now
active.
To return to the standard mode, repeat the procedure but use the dark (
) key to select
exposure level “5” in step 3.
USER PROGRAMS
The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired.
Setting the power save modes, auto clear time, stream feeding mode and
resolution of AUTO & MANUAL mode
Press and hold down the light (
seconds until all the alarm indicators (
) and dark (
) keys simultaneously for more than 5
) blink and “ ” appears in the display.
,
,
,
1
2
Use the copy quantity (
preheat mode, 3:auto power shut-off timer, 5:auto power shut-off mode 6:resolution of AUTO
& MANUAL mode). The selected number will blink in the left side of the display.
) key to select a user program number (1: auto clear time, 2:
Press the start (
) key. The entered program number will be steadily lit and the currently
selected parameter number for the program will blink on the right side of the display.
3
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the desired parameter using the copy quantity (
number will blink on the right of the display.
) key. The entered parameter
4
Program
Mode
Parameters
No.
1
Auto clear time
0 -> OFF, 1 -> 10 sec., 2 -> 30 sec., *3 -> 60 sec.,
4 -> 90 sec., 5 -> 120 sec.
2
3
Preheat mode
*0 -> 30 sec., 1 -> 60 sec., 2 -> 90 sec.
Auto power shut- off timer
0 -> 2 min, *1 -> 5 min., 2 -> 15 min., 3 -> 30 min.,
4 -> 60 min., 5 -> 120 min.
4
5
6
Stream feeding mode
0 -> OFF, *1 -> ON
Auto power shut- off mode
0 -> OFF, *1 -> ON
Resolution of AUTO &
MANUAL mode
*0 -> 300 dpi, 1 -> 600 dpi
* Factory default settings are indicated with an asterisk (*).
Press the start (
) key. The right-hand number in the display will be steadily lit and the
entered value will be stored.
5
To change the setting or to set another mode, press the clear (
to step 2.
) key. The unit will return
Press the light (
) or dark (
) key to return to the normal copy mode.
6
DISPLAYING TOTAL NUMBER OF COPIES
Use the following procedure to display the total number of copies.
Press the clear (
) key to reset the display to zero.
1
2
Press and hold down the clear (
copies will appear in two steps, each with three digits.
) key for approximately 5 seconds. The total number of
Example: Total number of copies is 1,234.
SPECIAL FUNCTIONS
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
This chapter describes how to replace the toner cartridge and how to clean the unit.
Be sure to use only genuine TOSHIBA parts and supplies.
For best copying results, be sure to use only TOSHIBA Genuine Supplies which are
designed, engineered, and tested to maximise the life and performance of TOSHIBA copiers.
Look for the Genuine Supplies label on the toner package.
TONER CARTRIDGE REPLACEMENT ................................................................................5-2
CLEANING THE UNIT ............................................................................................................5-5
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
TONER CARTRIDGE REPLACEMENT
When the toner cartridge replacement required (
) indicator lights up, replacement of the toner cartridge
will be needed soon. Obtain a new cartridge. When the toner cartridge replacement required (
) indicator
blinks, the toner cartridge must be replaced before copying can be resumed. Replace the toner cartridge
by following the procedure below.
During long copy run of a dark original, the start (
light up, and the unit stop, even though toner is left. The unit will feed toner up to 2 minutes
and then the start ( ) indicator will light up. Press the start ( ) key to restart copying.
) indicator may blink, the indicator
Ensure that the bypass tray is open and then open the side cover while pressing the side
cover open button.
1
2
Push gently on both sides of the front cover to open the cover.
MAINTENANCE
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2
Gently pull the toner cartridge out while pressing the lock release lever.
3
Toner cartridge lock
release lever
•
•
After removing the toner cartridge, do not shake it or tap on it. Doing so may cause toner
to leak from the cartridge. Put the old cartridge immediately in the bag contained in the
box of the new cartridge.
Dispose of the old toner cartridge in accordance with local regulations.
Remove the toner cartridge from the bag. Grasp the cartridge on both sides and shake it
horizontally four or five times. After shaking the cartridge, remove the toner seal.
4
5
4 or 5 times
Shutter
Toner seal
Grasp the toner cartridge as shown in the illustration. Do not hold the cartridge by the
shutter. Be sure to only shake the cartridge before the toner seal is removed.
Gently insert the toner cartridge along the guides until it locks in place while pushing the lock
release lever. Remove the tape from the shutter. Pull the shutter out of the toner cartridge as
shown in the illustration. Discard the shutter.
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Close the front cover and then the side cover by pressing the round projections near the side
cover open button. The indicator will go out and the start ( ) indicator will light up.
6
When closing the covers, be sure to close the front cover securely and then close the side
cover. If the covers are closed in the wrong order, the covers may be damaged.
Even after a new toner cartridge is installed, the start (
) indicator may not light up,
indicating copying cannot be restarted (toner is not sufficiently fed). In this case, open and
close the side cover. The copier will feed toner again approximately 2 minutes and then
copying can be restarted.
MAINTENANCE
Download from Www.Somanuals.com. All Manuals Search And Download.
5-4
CLEANING THE UNIT
Proper care is essential in order to get clean, TOSHIBA copies. Be sure to take a few minutes to regularly
clean the unit.
•
•
Before cleaning, be sure to turn the power switch off and remove the power cord from the
outlet.
Do not use thinner, benzene or other volatile cleaning agents. Doing so may cause
deformation, discoloration, deterioration or malfunction.
Cabinet
Wipe the cabinet with a soft, clean cloth.
Original table and the back side of the original cover
Stains on the glass or cover will also be copied. Wipe the glass and cover with a soft, clean cloth. If
necessary, dampen the cloth with a glass cleaner.
Original table
Original cover
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Transfer charger
If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the
following procedure.
Turn the power switch off. (p.3-4)
1
2
3
Ensure that the bypass tray is open and then open the side cover while pressing the side
cover open button.
Take the charger cleaner out by holding the tab. Set the charger cleaner onto the right end of
the transfer charger, gently slide the cleaner to the left end, and then remove it. Repeat this
operation two or three times.
Slide the charger cleaner from the right end to the left end along the groove of the transfer
charger. If the cleaner is stopped on the way, smudges on copies may occur.
Return the charger cleaner to its original position. Close the side cover by pressing the round
projections near the side cover open button.
4
Turn the power switch on. (p.3-3)
5
MAINTENANCE
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING THE
UNIT
This chapter describes misfeed removal and troubleshooting.
TROUBLESHOOTING ............................................................................................................6-2
STATUS INDICATORS ............................................................................................................6-3
MISFEED REMOVAL ..............................................................................................................6-4
DEVELOPER REQUIRED......................................................................................................6-7
MAINTENANCE REQUIRED .................................................................................................6-7
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If any problem occurs, check the list below before contacting your authorised service representative.
Problem
Possible cause
Unit plugged in?
Solution
Page
3-3
Plug the unit into a grounded outlet.
Turn the power switch on.
Unit does not
operate.
Power switch on?
3-3
Side cover closed securely?
Front cover closed?
Gently close the side cover.
5-4
Gently close the front cover and then
close the side cover.
5-4
Blank copies
Is the original placed face
down on the original table?
Place the original face down on the
original table.
3-5
3-6
3-7
3-6
5-5
Is original image too dark or
too light?
Adjust the exposure manually.
Copies are
too dark or
too light.
Is the unit in the automatic
exposure mode?
Adjust the automatic exposure level.
Cancel the photo exposure mode.
Is the unit in the photo
exposure mode?
Dust, dirt, smud- Original table or original cover Clean regularly.
ges appear on
dirty?
copies.
Original smudged or blotchy? Use a clean original.
--
Striped copies Is transfer charger clean?
Non-standard paper used?
Clean the transfer charger.
5-6
2-2
Use standard paper. If using special
papers, feed the paper through the
single bypass.
Paper curled or damp?
Store paper flat in the wrapper in a dry
location.
--
Pieces of paper inside unit?
Remove all pieces of misfed paper.
6-4
2-4
Paper misfeeds
frequently.
Paper guides in the paper tray Set the guides properly depending on
not set properly?
the paper size.
Too much paper in the paper
tray?
Remove excessive paper from the tray.
2-4
Is the paper too heavy?
Paper damp?
Use paper within the specified range.
2-2
7
Replace with dry paper. If the unit is not
used for long time, remove the paper
from the paper tray and store it in its
wrapper in a dry location.
Images rub off
the copy easily.
TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2
STATUS INDICATORS
When the following indicators light up or blink on the operation panel or the following alphanumeric codes
appear in the display, solve the problem immediately referring to both the table below and the relevant
page.
Be sure to use only genuine TOSHIBA parts and supplies.
Indication
Cause and remedy
Page
6-7
Developer
replacement re-
quired indicator
Developer is required. contact your
authorised service representative.
Steadily lit
Replacement of Toner cartridge will be
needed soon. Prepare a new cartridge.
5-2
5-2
6-4
Steadily lit
Blinking
Blinking
Toner cartridge
replacement re-
quired indicator
Toner cartridge must be replaced. Replace
it with a new one.
A misfeed has occurred. Remove the
misfed paper referring to the description of
“Misfeed Removal”
Misfeed indicator
Maintenance
indicator
Service by an authorised TOSHIBA service
technician is required.
6-7
4-2
4-2
Steadily lit
The unit is in the preheat mode. Press any
key to cancel the preheat mode.
Power save indicator
is steadily lit.
The unit is in the auto power shut-off mode.
Press the start (
) key to cancel the auto
power shut-off mode.
The paper tray indicator is
blinking.
--
The paper tray is not installed properly.
Push the tray into the unit securely.
5-2
The toner cartridge is not installed. Check if
the cartridge is installed. If “CH” is blinking
even if a cartridge is installed properly,
contact your TOSHIBA service centre
immediately.
“CH” is blinking in the display.
--
Side cover is open. Close the side cover
securely by pressing the round projections
near the side cover open button.
“CH” is steadily lit in the display.
2-4
6-4
--
The paper tray is empty.
Load paper.
“P” is blinking in the display.
A misfeed has occurred in the paper tray,
bypass tray. Remove the misfed paper.
The unit will not function. Turn the power
switch off, remove the power cord from
outlet, and contact your authorised service
representative.
A letter and a number appear
alternately.
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
MISFEED REMOVAL
When the misfeed (
) indicator blinks
or in the display, the unit will stop because of a misfeed.
Open the side cover, in that order.
To open the side cover, see “TONER CARTRIDGE REPLACEMENT” (p. 5-2)
1
2
Check the misfeed location. Remove the misfed paper following the instructions for each
location in the illustration below. If the misfeed (
) indicator blinks, proceed to “A: Missfeed
in the paper feed area” (p. 6-5).
If the misfed paper is seen from
this side, proceed to "C: Misfeed
in the transport area".
If paper is misfed here, proceed to "B:
Misfeed in the fusing area".
If paper is misfed here, proceed to "A:
Misfeed in the paper feed area".
TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
6-4
A: Misfeed in the paper feed area
Gently remove the misfed paper from the paper feed area as shown in the illustration. When
the misfeed (
) indicator blinks, and the misfed paper is not seen from the paper feed area,
1
pull out the paper tray and remove the misfed paper.If the paper cannot be removed, proceed
to “B: Misfeed in the fusing area”.
The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so
may cause a burn or other injury.
•
•
Do not touch the photoconductive drum (green portion) when removing the misfed paper.
Doing so may cause smudges on copies.
If the paper has been fed through the multi-bypass tray, do not remove the misfed paper
through the multi-bypass tray. Toner on the paper may stain the paper transport area,
resulting in smudges on copies.
Close the side cover by pressing the round projections near the side cover open button. The
misfeed ( ) indicator will go out and the start ( ) indicator will light up.
2
B: Misfeed in the fusing area
Lower the fusing unit release lever.
1
Fusing unit release lever
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Gently remove the misfed paper from under the fusing unit as shown in the illustration. If the
paper cannot be removed, proceed to “C: Misfeed in the transport area”.
2
3
The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so
may cause a burn or other injury.
•
•
Do not touch the photoconductive drum (green portion) when removing the misfed paper.
Doing so may cause smudges on copies.
Do not remove the misfed paper from above the fusing unit. Unfixed toner on the paper
may stain the paper transport area, resulting in smudges on copies.
Raise the fusing unit release lever and then close the side cover by pressing the round
projections near the side cover open button. The misfeed ( ) indicator will go out and the
start ( ) indicator will light up.
C: Misfeed in the transport area
Lower the fusing unit release lever.
See B: Misfeed in the fusing area (p. 6-5).
1
2
3
Open the front cover.
To open the front cover, see “TONER CARTRIDGE REPLACEMENT” (p. 5-2).
Rotate the feeding roller in the direction of the arrow and gently remove the misfed paper from
the exit area.
Feeding roller
TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
6-6
Raise the fusing unit release lever, close the front cover and then close the side cover by
pressing the round projections near the side cover open button. The misfeed ( ) indicator
4
will go out and the start (
) indicator will light up.
When closing the covers, be sure to close the front cover securely and then close the side
cover. If the covers are closed in the wrong order, the covers may be damaged.
DEVELOPER REQUIRED
When the developer replacement required (
) indicator lights up, the developer should be replaced.
DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN AUTORIZED TOSHIBA SERVICE
TECHNICIAN. Contact your service centre as soon as possible.
MAINTENANCE REQUIRED
When maintenance ( ) indicator lights up, service by an authorised TOSHIBA service technician is
required. Contact your service centre as soon as possible.
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
6-8
Installing the Software
This chapter explains how to install the software that allows the e-STUDIO120, and e-STUDIO150 to be
used as a printer and scanner, and the procedures for using the printer and scanner functions. The
following term is used in this chapter.
CD-ROM
Means the supplied CD-ROM with the e-STUDIO120/150 series software.
SOFTWARE FOR THE TOSHIBA PERSONAL MFP SERIES ...............................................7-2
HARDWARE AND SOFTWARE REQUIREMENTS ...............................................................7-3
BEFORE INSTALLATION .......................................................................................................7-3
INSTALLING THE SOFTWARE...............................................................................................7-5
INDICATORS ON THE OPERATION PANEL ...................................................................... 7-15
USING THE PRINTER MODE ............................................................................................. 7-16
USING THE SCANNER MODE ........................................................................................... 7-18
HOW TO USE THE ONLINE MANUAL................................................................................ 7-26
USING OTHER INSTALLED DRIVERS .............................................................................. 7-28
CONNECTING THE INTERFACE CABLE .......................................................................... 7-29
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE FOR THE TOSHIBA PERSONAL MFP
SERIES
The supplied CD-ROM includes software for this unit.
MFP driver
Scanner driver
Permits you to operate scanning function of this unit with TWAIN-compliant and WIA-compliant application.
Printer driver
Enables you to use the printer function of this unit with your computer.
Print StatusWindow
The print state and information on current printing are displayed on the status monitor window.
Desktop Document Manager
An integrated software environment that makes it easy to manage document and image files and launch
applications.
Button Manager
Button Manager enabling the SCANNER ( ) key located on the unit.
The scanning feature is only available with Windows 98/Me/2000/XP using a USB
connection. For users running Windows 95/NT 4.0 or using a parallel connection, only
printing is available.
INSTALL THE SOFTWARE
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE AND SOFTWARE REQUIREMENTS
Check the following hardware and software requirements in order to install the software.
Computer type
IBM PC/AT or compatible computer equipped with a USB1.1*1 or bi-
directional parallel interface (IEEE 1284)
Operating system*2
Windows 95, Windows 98, Windows Me, Windows NT Workstation 4.0
(ServicePack 5 or later)*3, Windows 2000 Professional*3, Windows XP
Professional*3, Windows XP Home Edition*3
Display
800 x 600dots (SVGA) display with 256 colors (or better)
150MB or more
Hard disk free space
Other requirementfor
hardware
An environment on which any of the operating systems listed above can
fully operate
*1Compatible with Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or
Windows XP Home Edition preinstalled model with USB interface equipped as standard.
*2Printing is unavailable in MS-DOS mode.
*3The administrator’s authorisation is required to install this software using this installer.
BEFORE INSTALLATION
The following table shows the drivers and software that can be installed for each version of Windows and
interface connection method.
MFP Driver
Printer driver/
Print Status
Window
Scanner
driver
Button
Manager
Desktop
Document
Manager
Available
Available
Available
Users of Windows 98/Me/2000/XP who
will use the USB interface connection
Users of Windows 98/Me/2000/XP who
will use the parallel interface connection
*1
*2
Available
Not Available Not Available Available
Windows 95/NT 4.0 users
*1When the unit is connected through the parallel port, the Print Status Window can only be used when the
parallel port is set to ECP mode. To set the parallel port mode, refer to your computer manual or ask the
manufacturer of your computer.
*2Desktop Document Manager can be installed when using a parallel interface connection, however, the
unit’s scanner function cannot be used.
Is there another GDI printer driver or a Windows Printing System printer driver already
installed? If installed, change the printer port setting. For the change of the printer port
setting, see USING OTHER INSTALLED DRIVERS.(p. 7-28)
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Flow of installation
Refer to the following table and then begin installation.
Operatingsystem
Interface
Reference pages for how to install
Windows XP
USB/
Installing onto Windows XP (USB/parallel interface) (p. 7-5)
Parallel
USB
Installing onto Windows 98/Me/2000 (USB interface) (p. 7-9)
Windows 98
Windows Me
Parallel
Installing onto Windows 95/98/Me/NT4.0/2000 (Parallel
interface) (p. 7-9)
USB
Installing onto Windows 98/Me/2000 (USB interface) (p. 7-9)
Parallel
Installing onto Windows 95/98/Me/NT4.0/2000 (Parallel
interface) (p. 7-9)
USB
Installing onto Windows 98/Me/2000 (USB interface) (p. 7-9)
Windows 2000
Parallel
Installing onto Windows 95/98/Me/NT4.0/2000 (Parallel
interface) (p. 7-9)
Windows 95 / NT 4.0
Parallel
Installing onto Windows 95/98/Me/NT4.0/2000 (Parallel
interface) (p. 7-9)
INSTALL THE SOFTWARE
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE SOFTWARE
The following term is used in this section.
MFP
Means the unit as a printer and scanner.
•
•
•
•
For this description, it is assumed that the mouse is configured for right hand operation.
To print or scan, the MFP must be in the online state.
The scanner feature only works when using a USB interface cable.
If any error message appears, solve the problem following the instructions on the screen.
After your problem is solved, the installing procedure will be continued. Depending on
your problem, you may have to exit the installer. In this case, click the “Cancel” button to
exit the installer. After solving your problem, reinstall the software from the beginning.
Installing onto Windows XP (USB/parallel interface)
Before starting the installation, make sure the USB or parallel interface cable is not connected to the MFP.
Insert the supplied CD-ROM into your CD-ROM drive.
1
2
Click the “start”button, click “My Computer”( ), and then double-click the CD-ROM ( ) icon.
When any of “Found New Hardware Wizard” messages appear during the software
installation, be sure to click the “Cancel” button.
Double-click the “setup” ( ) icon.
3
If the language selection screen appears after you double click the “setup” icon, select the
language you wish to use and click the “Next” button. (Normally, the correct language is
selected automatically.)
Select the software packages to be installed, and
then click the “Next” button.
The software packages with checkmark ( ) on the list
on the screen will be installed.
Click the “Display README” button to show the
information on the selected package.
4
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
If you are using the parallel interface connection, do not select the Button Manager
checkbox because this feature is not supported with the parallel interface.
If the following screen appears, click the “OK” button. Review the contents in See
“BEFORE INSTALLATION” (p.7-3), and then select only appropriate the software
packages to be installed.
Review the software packages to be installed on
the screen, and then click the “Start” button.
The software packages to be installed will be displayed
on the screen. If inappropriate packages are displayed,
click the “Back” button to select appropriate packages
again.
5
6
Copying files for MFP driver installation (This step will start if it was selected in step 4).
1. After confirming the message in the “Welcome” window, click the “Next” button.
2. A dialog box appears asking you to verify that the USB or parallel interface cable is not connected
to the MFP. Make sure that the interface cable is not connected and click the “Next” button.
3. Click the “Next” button in the dialog box to install the
MFP driver or Cancel to quit the installation.
•
•
The setup program will start to copy the files.
If the following screen appears while the files are
being copied (the message may appear more than
once), click “Continue Anyway”.
4. When the “The MFP driver installation is complete.” dialog box appears, click the “OK” button.
The Button Manager installer will start.
•
INSTALL THE SOFTWARE
Download from Www.Somanuals.com. All Manuals Search And Download.
7-6
Begin installation of the Button Manager (This step will start if it was selected in step 4).
1. After confirming the message in the “Welcome” window, click the “Next” button.
2. Read the message in the “Please read the following information.” window, and then click the “Next”
button.
3. When a message appears that lets you specify the location for the software to be installed, click the
“Next” button.
7
4. If the program displays “Do you want the Button Manager added to Windows Startup?”, check
“Yes” and click the “OK” button.
•
The setup program will start to copy the files.
5. Click the “Finish” button when the message informs you that setup is successful.
The Desktop Document Manager installer will start.
•
Begin installation of the Desktop Document Manager (This step will start if it was selected in
step 4).
1. After confirming the message in the “Welcome to Desktop Document Manager installation” window,
8
9
click the “Next” button.
2. Read the message in the “Information” window, and then click the “Next” button.
3. When the “Choose Destination Location” window appears, click the “Next” button.
4. When the “Select Program Folder” window appears, click the “Next” button.
•
The setup program will start to copy the files.
5. Click the “Finish” button when the message informs you that Setup is complete.
Click the “Close” button when the message informs
you that“Setup has finished”.When the“Now connect
the MFP interface cable to the PC” dialog box
appears, click the “OK” button.
After the installation, a message to restart your
computer may be displayed. In this case, click the
“Yes” button to restart your computer.
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the USB interface cable or parallel interface cable. (See p. 7-29)
Windows will detect the MFP and the Plug and Play screen will appear. If you are using Windows
XP with the parallel interface, go to step 12.
10
11
Begin installation of the scanner driver.
1. “TOSHIBA e-STUDIOxxx” (where xxx is the model name of your MFP) will appear in the “Found
New Hardware Wizard” dialog box. Select “Install the software automatically (Recommended)”
and click the “Next” button.
2. The “Install hardware” dialog box will appear. Click the “Continue Anyway” button.
3. When installation of the driver is completed, click the “Finish” button to finish the scanner driver
installation.
Begin installation of the printer driver.
1. “TOSHIBA e-STUDIOxxx” (where xxx is the model name of your MFP) will appear in the “Found
New Hardware Wizard” dialog box. Select “Install the software automatically (Recommended)”
and click the “Next” button.
2. The “Hardware Installation” dialog box will appear. Click the “Continue Anyway” button.
3. When installation of the driver is completed, click the “Finish” button to finish the printer driver
installation.
12
You have completed the installation of all the software.
INSTALL THE SOFTWARE
Download from Www.Somanuals.com. All Manuals Search And Download.
7-8
Installing onto Windows 98/Me/2000 (USB interface)
Before starting the installation, make sure the USB interface cable is not connected to the MFP.
Insert the supplied CD-ROM into your CD-ROM drive.
1
2
Double-click “My Computer” ( ), and then double-click the CD-ROM ( ) icon.
When any of “Hardware Found”, or “Found New Hardware Wizard” messages appear
during the software installation, be sure to click the “Cancel” button.
Double-click the “setup” ( ) icon.
3
If the language selection screen appears after you double click the “setup” icon, select the
language you wish to use and click the “Next” button. (Normally, the correct language is
selected automatically.)
Select the software packages to be installed, and
then click the “Next” button.
4
The software packages with checkmark ( ) on the list
on the screen will be installed. Click the “Display
README” button to show the information on the selected
package.
If the following screen appears, click the “OK” button. Review the contents in “BEFORE
INSTALLATION” (See p. 7-3), and then select the appropriate driver software packages to be
installed.
Review the software packages to be installed on the screen, and then click the “Start” button.
The software packages to be installed will be displayed on the screen. If inappropriate packages are
displayed, click the “Back” button to select appropriate packages again.
5
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying files for MFP driver installation.
1. After confirming the message in the “Welcome” window, click the “Next” button.
2. A dialog box appears asking you to verify that the interface cable is not connected to the MFP. Make
sure that the interface cable is not connected and click the “Next” button.
3. Click the “Next” button in the dialog box showing the files
6
7
to be copied for installation of the MFP driver.
•
•
The setup program will start to copy the files.
In Windows 2000, if the following screen appears while
the files are being copied (the message may appear more
than once), click “Yes” in Windows 2000.
4. The following screen appears when all of the files for the
USB interface connection have been copied. If you are
not using a parallel interface cable for connection to the
MFP, please click the “No” button.
5. When the “The MFP driver installation is complete.” dialog box appears, click the “OK” button.
•
The Button Manager installer will start.
Begin installation of the Button Manager (This step will start if it was selected in step 4).
1. After confirming the message in the “Welcome” window, click the “Next” button.
2. Read the message in the “Please read the following information.” window, and then click the “Next”
button.
3. When a message appears that lets you specify the location for the software to be installed, click the
“Next” button.
4. If the program displays “Do you want to add Button Manager to Startup program?”, check “Yes” and
click the “OK” button.
•
The setup program will start to copy the files.
5. Click the “Finish” button when the message to inform you of the completion of the installation
appears.
•
The Desktop Document Manager installer will start.
INSTALL THE SOFTWARE
Download from Www.Somanuals.com. All Manuals Search And Download.
7-10
Begin installation of the Desktop Document Manager (This step will start if it was selected in
step 4).
1. After confirming the message in the “Welcome to Desktop Document Manager installation” window,
8
9
click the “Next” button.
2. Read the message in the “Information” window, and then click the “Next” button.
3. When the “Choose Destination Location” window appears, click the “Next” button.
4. When the “Select Program Folder” window appears, click the “Next” button.
•
•
The setup program will start to copy the files.
If the dialog box asking “This program is about to install
Desktop Document Manager imaging, which does not
support LZW compression.” appears, answer the question
to continue the Desktop Document Manager installation.
5. Click the “Finish” button when the message to inform you of the completion of the installation
appears.
Click the “Close” button when the message to inform
you of the completion of the installation appears.When
the “Now connect the MFP interface cable to the PC.”
dialog box or “After Windows system restart...” dialog
box appears, click the “OK” button.
After the installation, a message to restart your
computer may be displayed. In this case, click the
“Yes” button to restart your computer.
Connect the USB interface cable. (See p. 7-29)
Windows will detect the MFP and the Plug and Play screen will appear.
10
11
Follow the instructions in the Plug and Play screen that appears in your version of
Windows to begin the installation.
You have completed the installation of the software.
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing onto Windows 95/98/Me/NT4.0/2000 (Parallel interface)
Before starting the installation, make sure the USB or parallel interface cable is not connected to the MFP.
Insert the supplied CD-ROM into your CD-ROM drive.
1
Double-click “My Computer” ( ), and then double-click the CD-ROM ( ) icon.
2
When any of “Hardware Found”, or “Found New Hardware Wizard” messages appear
during the software installation, be sure to click the “Cancel” button.
Double-click the “setup” ( ) icon.
3
If the language selection screen appears after you double click the “setup” icon, select the
language you wish to use and click the “Next” button. (Normally, the correct language is
selected automatically.)
Select the software packages to be installed, and then
click the “Next” button.
The software packages with checkmark ( ) on the list on
the screen will be installed.
Click the “Display README” button to show the information
on the selected package.
4
In Windows 95/NT 4.0, “Button Manager” does not
appear. In Windows 98/Me/2000, do not select the
“Button Manager” checkbox. because this is not
supported when using the parallel interface.
The next screen appears. Make sure that the parallel interface cable is not connected, and
click “OK”.
5
Windows 95/NT 4.0
Windows 98/Me/2000
Check the contents of the package on the screen, and then click the “Start” button.
The software packages to be installed will be displayed on the screen. If inappropriate packages are
displayed, click the “Back” button to select only appropriate software packages.
6
INSTALL THE SOFTWARE
Download from Www.Somanuals.com. All Manuals Search And Download.
7-12
Copying files for MFP driver installation and parallel interface setup (This step will start if it
was selected in step 4).
1. After confirming the message in the “Welcome” window, click the “Next” button.
2. A dialog box appears asking you to verify that the USB or parallel interface cable is not connected
to the MFP. Make sure that the interface cable is not connected and click the “Next” button.
3. Click the “Next” button in the dialog box to install the MFP
7
driver or Cancel to quit the installation.
•
•
The setup program will start to copy the files.
In Windows 2000, if the following screen appears while
the files are being copied (the message may appear more
than once), click “Yes” in Windows 2000.
4. The following screen appears. Click the “Yes” button, and then the Model screen will appear. Select
the model number that is the same as the model name of your MFP and click the “Next” button.
•
Be sure to select the displayed model number that is the same as the MFP’s model name. If they
are not the same, the driver will not be installed correctly.
5. Establish the printer settings and click the “Next” button.
•
Select “LPT1” for the port to be used. If “LPT1” does not
appear, it is likely that another printer or peripheral device
is using “LPT1”. Check your other printers and peripheral
devices, and change the port setting as needed so no
device is using “LPT1”. If you wish the MFP to be your
default printer, select “Yes”. If not, select “No”.
6. When the “Setup has completed gathering all necessary installation information” dialog box
appears, click the “Yes” button.
•
The parallel interface driver is installed.
7. When the “The MFP driver installation is complete.” dialog box appears, click the “OK” button.
•
The Desktop Document Manager installer will start.
7-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Begin installation of the Desktop Document Manager (This step will start if it was selected in
step 4).
1. After confirming the message in the “Welcome to Desktop Document Manager installation” window,
8
9
click the “Next” button.
2. Read the message in the “Information” window, and then click the “Next” button.
3. When the “Choose Destination Location” window appears, click the “Next” button.
4. When the “Select Program Folder” window appears, click
the “Next” button.
•
•
The setup program will start to copy the files.
If the dialog box asking “This program is about to install
Desktop Document Manager imaging, which does not
support LZW compression.” appears, answer the
question to continue the Desktop Document Manager
installation.
5. Click the “Finish” button when the message to inform you of the completion of the installation
appears.
Click the “Close” button when the message to
inform you of the completion of the installation
appears.
When the “Now connect the MFP interface cable to
the PC.” dialog box or “After Windows system
restart...” dialog box appears, click the “OK” button.
After the installation, a message to restart your
computer may be displayed. In this case, click
the “Yes” button to restart your computer.
Connect the parallel interface cable. (p.7-30)
You have completed the installation of all the software.
10
INSTALL THE SOFTWARE
Download from Www.Somanuals.com. All Manuals Search And Download.
7-14
INDICATORS ON THE OPERATION PANEL
The ONLINE indicator and the start (
) indicator indicate the state of the printer or scanner.
POWER SAVE indicator
START indicator
Start indicator
On:
Blinking:
Indicates the unit is ready for copying or scanning is being performed.
The indicator blinks in the following situations:
•
•
When a print job is interrupted.
During initialization of the unit. (the cover has been opened and closed or the power
turned off and on.)
•
•
When reserving a copy job.
When toner is being replenished during a copy or print job.
Off:
The indicator is off in the following situations:
•
•
•
During copying or scanning.
The unit is in the auto power shut-off mode.
When a misfeed or error has occurred.
Power save indicator
On:
Indicates the unit is in a power save mode.
ONLINE indicator
SCANNER indicator
ONLINE indicator
The ONLINE key is pressed and on line and off line are changed.
On:
Blinking:
Off:
Indicates the unit is ready for printing or scanning is being performed. (On line)
Printing or data is being received from a computer.
Copying is being performed. (Off line)
Scanner indicator
On:
The SCANNER ( ) key has been pressed and the unit is in scanner mode.
Blinking:
Off:
A scan job is being executed from the computer, or scan data is stored in the unit’s memory.
The unit is in the copy mode.
7-15
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE PRINTER MODE
For problems with the printer function, see the online manual or the help file for the driver.
Opening the printer driver from the start menu
Open the printer driver setup screen by the method shown below.
Click the “start” button.
1
2
3
Click“Control Panel”, select “Printers and Other Hardware”, and then click “Printers and Faxes”.
On Windows 95/98/Me/NT4.0/2000, select “Settings” and click “Printers”.
Click the “TOSHIBA e-STUDIOxxx” (where xxx is the model name of your unit) printer driver
icon and from the “File” menu select “Properties”.
On windows NT 4.0, select “Document Defaults” to open the printer driver setup screen.
Click “Printing Preferences” button in the “General” tab.
On Windows 95/98/Me, click the “Setup” tab.
The printer driver setup screen will appear.
4
Refer to the Windows manual or help file for more information on the “General” tab, “Details”
tab, “Color Management” tab and “Sharing” tab.
How to print
Make sure that the paper of the desired size and type is loaded in the tray. See “LOADING
PAPER”.
1
When printing from the bypass tray, configure the settings in the printer driver first, execute
printing, and then load the paper.
Open the document you intend to print, and select “Print” from the application’s “File” menu.
2
3
Make sure that “TOSHIBA e-STUDIOxxx” (where xxx is the model name of your unit) are
selected as the current printer.If you intend to change any print setting, click the “Preferences”
button to open the setting dialog.
On Windows 95/98/Me/NT 4.0, click the “Properties” button.
On Windows 2000, the “Properties” button does not appear. Set your preferences by switching the tab
in the “Print” dialog box.
INSTALL THE SOFTWARE
7-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Specify the print settings including the number of copies, media type, and print quality, and
then click the “Print” button to start printing.
On Windows 95/98/Me/NT 4.0, click the “OK” button to start printing.
4
For details on print settings, see the online manual or the help file for the printer driver.
•
If copying is being performed when printing is started, copying will continue. After
copying is complete, printing will be executed when the clear (
) key is pressed twice,
the ONLINE key is pressed to switch the unit to the online state or approximately 60
seconds (auto clear time)* elapse.·
•
•
•
The auto clear time varies with a user program setting. See “USER PROGRAMS” (p. 4-3)
Preheat mode and auto power shut-off mode will be cancelled when printing is started.
If the paper size specified from the software application is larger than the paper size in
the printer, part of the image that is not transferred to the paper may remain on the
surface of the drum. In this case, the backside of the paper may become dirty. If this
occurs, change to the correct size paper and print two or three pages to clean the image.
If you start a print job while a scan job is in progress, the print data will be stored in the
unit’s memory. When the scan job is completed, printing will begin.
•
About interrupt copying
If you press the start (
) key to begin a copy job while a print job using the paper tray is in progress, the
copy job will begin automatically after the print data in the unit’s memory is printed (interrupt copying).
When this is done, the print data remaining in the computer is not sent to the unit. When the copy job ends,
press the clear (
) key twice, or press the ONLINE key once to change the unit to the online state (See
p. 7-15), or wait until the set auto clear time (see p. 4-2) elapses. The remaining print data will be sent to the
unit and printing will resume. Interrupt copying is not possible during a print job using the bypass tray.
Configuring the Option
After you complete the installation of printer drivers, you should configure the option setting on the printer
drivers.
Select the printer driver in the Printers folder.
Then click on "File" and select " Properties".
1
Click on the "Utility" tab and set the Input Tray Options.
2
Click on "OK" to save setting.
3
On Windows 2000 or Windows NT 4.0, the „Utility“ tab can be displayed by selecting
„Document Defaults“ (for Windows NT 4.0) or “printing Preferences” (for Windows 2000/XP)
but the option setting on this tab are impossible. The option setting should be preformed
according to the above procedures.
7-17
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SCANNER MODE
For problems with the scanner function, see the online manual or the help file for the driver.
Using the Button Manager
Setting up the Button Manager
The scanner driver for this unit includes an STI (Still image) driver and WIA (Windows Image Acquisition)
driver. You can install software that supports the STI driver and WIA driver to enable scanning using only
the operation panel of the unit.
The Button Manager accessory software supports the STI driver and WIA driver. Setup that is required in
Windows to use the Button Manager is explained in the following.
Windows XP
Click the “start” button, select “Control Panel” and click “Printers and Other Hardware”, and
then click “Scanners and Cameras”in the start menu.Right click the “TOSHIBA e-STUDIOxxx”
(where xxx is the model name of your unit) icon and click “Properties” in the menu that
appears.
1
In the “Properties” screen, click the “Events” tab.
2
Click the “Select an event” button and select
“ScanMenu SC1” from the pull-down menu. Select
“Button Manager (TOSHIBA Personal MFP series)”
in “Start this program” and click “Apply”.
3
If you prefer a specific application to be opened instead of
Button Manager, refer to page 20 of the Online manual. Do
not make the application selection in this screen.
Repeat Step3 to set “ScanMenu SC2” through “ScanMenu SC6” .
Click the “Select an event” button and select “ScanMenu SC2” from the pull-down menu. Select
“Button Manager (TOSHIBA Personal MFP series)” in “Start this program” and click “Apply”. Do the
same for each ScanMenu through “ScanMenu SC6”.
4
When the settings have been completed, click the “OK” button to close the screen. When the settings
have been completed in Windows, start the Button Manager. Adjust detailed settings and then scan
an image from the unit. For the procedures for starting Button Manager and adjusting settings, see
See “SCAN PARAMETER SETTING DIALOG BOX” (P. 7-20).
INSTALL THE SOFTWARE
7-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 98/Me/2000
To scan directly into an application using the Button Manager on Windows 98, Windows Me and Windows
2000. Set the Event Manager properties to send only to Button Manager as shown below.
Click the“Start”button, select“Control Panel”from“Settings”, and open“Scanners and Cameras”
in start menu.
1
In Windows Me, it occasionally happens that the “Scanners and Cameras” icon does not
appear immediately after installation of the MFP driver is completed. If the icon does not
appear, click “View all Control Panel options” in the Control Panel and display the “Scanner
and Cameras” icon.
Select “e-STUDIOxxx” (where “xxx” is the model name of your unit), and click the “Properties”
button.
2
In Windows Me, right click “e-STUDIOxxx” (where “xxx” is model name of your unit) and click “Properties”
in the menu that appears.
In the “Properties” screen, click the “Events” tab.
3
Click the “Scanner events” button and select “ScanMenu SC1”
from the pull-down menu. Select “Button Manager (TOSHIBA
Personal MFP series)” in “Send to this application” and click
“Apply”.
4
If other application are shown, deselect the checkboxes for
the other applications and leave only the Button Manager
checkbox selected.
Repeat Step4 to set “ScanMenu SC2” through “ScanMenu SC6”.
Click the “Scanner events” and select “ScanMenu SC2” from the pull-down menu. Select “Button
Manager (TOSHIBA Personal MFP series)” in “Start this program” and click “Apply”. Do the same for
each ScanMenu through “ScanMenu SC6”.
5
When the settings have been completed, click the “OK” button to close the screen. When the settings
have been completed in Windows, start the Button Manager. Adjust detailed settings and then scan
an image from the unit. For the procedures for starting Button Manager and adjusting settings, see
“Scan Parameter Setting Dialog Box” (Next page).
7-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Scan Parameter Setting Dialog Box
After you have completed the Button Manager settings in Windows,
configure the scan settings in Button Manager. To configure the scan
settings in Button Manager, right click the ( ) icon in the Taskbar and
select “Setting” from the menu that appears.
For details on configuring the scan settings in Button Manager, see the
online manual or the help file.
This is the corresponding setting in the Button Manager to
automatically send multiple images in full color at 75 dpi to
Desktop Document Manager using the operation panel “SC1”
SCANNER ( ) key selection.
•
This dialog shows the SC1 event set to go directly to Button Manager. With the Button
Manager set to send the image to Desktop Document Manager. (factory default setting)
Desktop Document Manager will open after acquiring the image automatically.
The SPF shown on the dialog box means the ADF (Auto Document Feeder).
For optimum performance when performing SC3 (Scan to FAX) it is recommended to set
the Color Mode to Monochrome (no green).
•
•
Flow of the Button Manager setting
The Button Manager can directly handle a e-STUDIOxxx (where xxx is the model name of your unit) series
device event and start your selected application according to the scan setting made on the e-STUDIOxxx
(where xxx is the model name of your unit) operation panel (SC1, SC2, SC3, SC4, SC5, SC6).
This will scan directly into your application from the device.
Scanner e-
STUDIOxxx
(where xxx is
the model
name of your
unit)
Event
Manager
Button
Manager
User
selected
application
Windows OS
No Selection
dialog is
displayed.
The user
application
opens.
SCANNER
key pressed.
INSTALL THE SOFTWARE
Download from Www.Somanuals.com. All Manuals Search And Download.
7-20
The settings for the Windows Event Manager for the TOSHIBA
e-STUDIOxxx (where xxx is the model name of your unit)
device allow the user to take advantage of the TOSHIBA
Button Manager to take control of events from Windows and
send scanned images to any of six different applications
according to the Button Manager setting.
This can be done with the Windows OS showing the Event
Manager selection dialog or directly into a selected application
if the Button Manager is the only allowed handler for device
events from the TOSHIBA e-STUDIOxxx (where xxx is the
model name of your unit).
This is done by changing the Windows device settings for the
e-STUDIOxxx (where xxx is the model name of your unit) in
the Scanner and Camera device settings in the Control Panel.
This is the Control Panel
Properties dialog for "scanners and
Cameras".
All About The Windows Event Manager and scanner events in Windows
98, Windows Me, Windows 2000 and Windows XP.
Windows Platforms provide a mechanism for software to handle external events for a scanner device like
the TOSHIBA e-STUDIOxxx (where xxx is the model name of your unit) series products.This mechanism is
controlled by the device manager on a device basis. Applications that can handle events from a scanner/
camera device register with the Windows Event Manager and shown as available in the registered
applications. The path an event takes to get to the user’s selected application depends upon the event
settings for the device.
Scanner e-
STUDIOxxx
(where xxx is
the model
name of your
unit)
Event
Manager
Event
User selects
an
application.
Manager
selection
dialog
Windows OS
The user
application
opens.
Displayed on
screen
SCANNER
key pressed.
This is the Windows Event Manager Selection Dialog.
Shown are two applications registered to handle the
scanner event from the e-STUDIOxxx (where xxx
is the model name of your unit) device.
7-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SCANNER key to begin scanning
•
•
Scanning is not possible during a copy job.
If the unit is used to begin a scan job during a print job, the scan job will be stored and
scanning will begin when the print job is completed.
Press the SCANNER ( ) key.
The unit enters scan mode.
1
Place the original you wish to scan on the original table.
For the procedure for placing the original, see “ORIGINAL PLACEMENT” (page 3-5)
2
3
Press the up copy quantity key to display the number
of the application that you wish to use for scanning.
The application numbers are initially as follows.
Application number Application launched
SC1
SC2
SC3
SC4
SC5
SC6
Desktop Document Manager (if installed)
E-mail (your standard e-mail program in the Windows OS you are using)
Fax (if a fax program is installed)
OCR (if an OCR program is installed)
Microsoft Word (if installed)
Any application set in Button Manager
INSTALL THE SOFTWARE
Download from Www.Somanuals.com. All Manuals Search And Download.
7-22
Press the start (
) key.
The selected application launches and scanning begins.
If the following screen appears, select Button Manager and
click “OK”. Button Manager starts and the application
associated with Button Manager starts. If you want only
Button Manager to start in this case, set up Button Manager
for use in Windows as explained in See “Setting up the
Button Manager” (p. 7-18).
1
Opening the scanner driver and scanning from your
computer
Follow the steps below to open the scanner driver setup screen. As an example, this instruction is given
using Desktop Document Manager as an image capture application.
•
•
Scanning is not possible during a copy and print job.
The method for starting the scanner driver differs depending on the type of application.
Refer to the manual or the help file of your application.
Using the TOSHIBA TWAIN
Place the original you wish to scan on the original table.
For the procedure for placing the original, see “ORIGINAL PLACEMENT” (p. 3-5).
1
After starting Desktop Document Manager, click the
“File” menu and select “Select Scanner”.
2
Click here
7-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Select “TOSHIBA Personal MFP series”, and click the “Select”
button.
3
Click here
If you use more than one scanning device, select the scanner you want to use through the
application. The method for accessing the “Select Scanner” option, depends upon the
application. For more information, see the online manual or the help file of your application.
Select “Acquire Image” from the “File” menu, or click
the “Acquire” button ( ) .
4
5
Set the configuration for scanning (refer to the online manual and help file), and click the
“Scan” button.
Scan is started.
INSTALL THE SOFTWARE
Download from Www.Somanuals.com. All Manuals Search And Download.
7-24
Scanning with the “Scanner and Camera Wizard” in Windows XP
Windows XP includes as a standard feature an image scanning function. The procedure for scanning with
the “Scanner and Camera Wizard” is explained here.
To cancel scanning, click the “Cancel” button in the screen that is displayed.
Place the original you wish to scan on the original table.
For the procedure for placing the original, see “ORIGINAL PLACEMENT” (p. 3-5).
1
2
Click the “start”button, select “Control Panel”, and click
“Printers and Other Hardware”, and then click “Scanners
and Cameras” in the start menu. Click the “TOSHIBA
e-STUDIOxxx” (where xxx is the model name of your
unit) icon and click “Get picture” in “Imaging Tasks”.
The“Scanner and CameraWizard”appears.Click“Next”
and establish the basic settings for scanning.
For information on the settings, see the Windows XP help
file. After completing each setting, click “Next”.
3
Select a name, format, and folder for the scanned image.
For information on the image name, file format, and folder,
see the Windows XP help file.
4
Scanning begins.When scanning ends, select the next
task you wish to perform.
5
For information on each selection, see the Windows XP
help file. To quit the “Scanner and Camera Wizard”, select
“Nothing. I’m finished working with these pictures.” and click
“Next”.
Click “Finish” in the screen that appears.
The “Scanner and Camera Wizard” closes and the scanned image is saved.
6
7-25
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ONLINE MANUAL
The online manual provides detailed instructions for operating the unit as the printer or scanner and a list
of methods for dealing with printing or scanner problems.
To access the online manual, your computer must have Acrobat Reader 5.0 or a later version. If it is not
installed, refer to “Installing Acrobat Reader” (Next page).
Contents of the online manual
The contents of the online manual are as follows. Check the online manual when you use this unit after all
the initial setup is completed.
How to use the online manual
Explains how to use the online manual.
Print
Provides information on how to print a document.
Scan
Explains how to scan using the scanner driver and how to adjust the settings for the Button Manager.
Troubleshooting
Provides instructions on how to solve driver or software problems.
Turn on your computer.
1
Insert the supplied CD-ROM into your CD-ROM drive.
2
3
Click the “start”button, click “My Computer”( ), and then double-click the CD-ROM ( ) icon.
On Windows 95/98/Me/NT 4.0/2000, double-click “My Computer” ( ), and then double-click the CD-
ROM ( ) icon.
Double-click the “Manual” folder, double-click
“English” folder, and then double-click the
“eStudio120_150.pdf”icon.
The following window will appear.
4
INSTALL THE SOFTWARE
7-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Click the
to read the online manual.
To close the online manual, click the ( ) button located at the top-right of the window.
5
•
•
The online manual can be printed out using Acrobat Reader. TOSHIBA recommends
printing out the sections which you refer to regularly.
Refer to “Help” of Acrobat Reader for more details on the operation and function of
Acrobat Reader.
Installing Acrobat Reader
Turn on your computer.
1
Insert the CD-ROM into the CD-ROM drive.
2
Click the “start”button, click “My Computer”( ), and then double-click the CD-ROM ( ) icon.
On Windows 95/98/Me/NT 4.0/2000, double-click “My Computer” ( ), and then double-click the CD-
ROM ( ) icon.
3
Double-click the “Acrobat” folder, and then double-click the “ar500enu.exe” icon.
Follow the on-screen instructions to install Acrobat Reader.
4
7-27
Download from Www.Somanuals.com. All Manuals Search And Download.
USING OTHER INSTALLED DRIVERS
If you use another GDI printer or a Windows Printing System printer, interference between printers may
occur and printing may not be performed properly. To use another GDI printer or a Windows Printing
System printer, you must change the port setting of the printer driver using the following procedure.
If another printer does not operate properly when the TOSHIBA Personal MFP series printer
driver is set to “FILE” as described below, uninstall the TOSHIBA Personal MFP series
printer driver. To uninstall the printer driver, see the online manual.
Click the “start” button.
1
2
Click “Control Panel”, click “Printer and Other Hardware” and then click “Printer and Faxes”.
On Windows 95/98/Me/NT4.0/2000, select “Settings” and then click “Printers”.
Right-click the “TOSHIBA e-STUDIOxxx”(where xxx is
the model name of your unit) icon in the printer dialog
box and then click “Properties”.
3
Click the “Port”tab (“Details”tab - on Windows 95/98/Me) in the “Properties”dialog box, select
“FILE”: in the “Print to the following port” list box, and click the “OK”.
4
Right-click the icon of the printer to be used and click “Properties”.
5
Click the “Port” tab (“Details” tab - on Windows 95/98/Me) in the “Properties” window, select
“LPT1” (or the currently used port), and click the “OK” button.
6
To use the TOSHIBA Personal MFP series again, perform the same procedure but select the
port to be used (for example, LPT1) in step 4.
INSTALL THE SOFTWARE
7-28
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING THE INTERFACE CABLE
This unit includes both USB and parallel interface connectors.
Interface cables for connecting the unit to your computer are not included with this unit. Please purchase
the appropriate cable for your computer.
Interface cable
Parallel interface cable
IEEE 1284-Shielded type bi-directional parallel interface cable (2 m (6 feet) Max.)
USB interface cable
Shielded twisted pair cable, high-speed transmission equivalent (2 m (6 feet) Max.)
•
If you intend to use the unit as a scanner, it must be connected to your computer with a
USB interface cable. The scanner function cannot be used if the unit is connected with a
parallel cable.
•
USB is available with a PC/AT compatible computer that was originally equipped with
USB and had Windows 98, Windows Me, Windows 2000 Professional, Windows XP
Professional or Windows XP Home Edition preinstalled.
•
Do not connect the interface cable before installing the MFP driver. The interface cable
should be connected during installation of the MFP driver. (See “INSTALLING THE
SOFTWARE” p. 7-5)
Connecting the USB interface cable
Obtain a shielded USB interface cable.
1
2
Insert the cable into the USB interface connector located
on the rear of the unit.
Insert the other end of the cable into the interface connector of your computer, or the USB hub
connected to your computer.
3
7-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the parallel interface cable
Obtain an IEEE1284 shielded parallel interface cable.
1
Ensure that your computer and unit are turned off.
2
3
Insert the cable into the parallel interface connector
located on the rear of the unit, and fasten with clasps.
Insert the other end of the cable into the interface connector of your computer.
4
INSTALL THE SOFTWARE
7-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
SPECIFICATIONS ...................................................................................................................8-2
OPTIONAL EQUIPMENT ........................................................................................................8-4
INDEX .....................................................................................................................................8-9
SOFTWARE LICENSE ......................................................................................................... 8-11
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Model
e-STUDIO120 (DP-1210)
e-STUDIO150 (DP-1510)
Type
Digital laser copier/printer, desk-top type
Copy system
Originals
Paper tray
Dry, electrostatic transfer
Sheets, bound documents
250 sheets (Paper tray) 50 sheet (Bypass tray)
100 sheets
Paper output tray
Original sizes
Original feed
Copy size
Max. A4 (8-1/2" x 14")
1 sheet
A6 to A4 (3-1/2" x 5-1/2" to 8-1/2" x 14") *1
Image loss
Max. 4mm (5/32") *2
Max. 4.5mm (11/64") *3
Copy speed
12 pages/min.
15 pages/min.
Continuous copying
Max. 99 pages subtractive counter
9.6 seconds
First-copy time
(Approximately)
(paper:A4, exposure mode: AUTO, copy ratio:100% )
Copy ratio
Variable:25% to 400% in 1% increments (total 376 steps)
Fixed: 25%, 70% 86%, 100%, 141%, 400% (25%, 64%, 78%, 100%,
129%, 400%)
Exposure system
Moving optical source, slit exposure (stationary platen) with
automatic exposure
Fusing system
Development system
Light source
Heat rollers
Magnetic brush development
Cold cathode fluorescent lamp
Resolution
600 x 300dpi (Auto/Manual mode)
600 x 600dpi (Photo mode)
Gradation
Bit depth
Sensor
2 levels
1 bit or 8 bit/pixel
color CCD
8 MB
Memory
Power supply
AC 120V ( 10%), 60 Hz ( 2%)
240V +6%, -10% in 240V power supply regions or local voltage
10% in other regions (For this copier’s power supply requirements,
see the name plate located on the back of the unit.)
Power consumption
1000 W
Overall
Width
Depth
607.6mm (23.9")
462.5mm (18.2")
16kg (35.3 lbs.)
dimensions
Weight (Approximately) *4
APPENDIX
8-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
e-STUDIO120 (DP-1210)
518mm (20.4")
e-STUDIO150 (DP-1510)
Width
Depth
Height
Unit dimensions
462.5mm (18.2")
295.6mm (11.6")
Operating conditions
Temperature: 10°C to 30°C (50°F to 86°F)
Humidity: 20% to 85%
Noise level
Sound Power Level LwA (1B=10dB)
Copying: 6.0 [B], Standby: 3.7 [B]
Sound Pressure Level LpA (bystander positions)
Copying: 46 [dB (A)], Standby: 23 [dB (A)]
Noise emission measurement in accordance with ISO 7779.
Ozone: less than 0.02 mg/m3
Dust: less than 0.075 mg/m3
Styrene: less than 0.07 mg/m3
Emission concentration
(measurement according to
RAL-UZ 62)
Optional equipment
Auto document feeder (MR-2014)
250-sheet paper feed unit (MY-1019)
*1 Feed paper lengthwise only.
*2 Leading and trailing edges.
*3 Along the other edges in totals.
*4 Not includes toner and drum cartridges.
Software
Printer/Scanner
Printing system
Printing size
Dry, electrostatic transfer
A6 to A4 (3-1/2" x 5-1/2" to 8-1/2" x 14") *1
Max. 12 pages/min. (Letter or A4)
Print speed
Continuous printing
Max. 99 pages subtractive counter
First-print time (Approximately) 9.6 seconds (Paper: A4) *2
Resolution
Printer
600 dpi
600 x 1200 dpi
Scanner
TOSHIBA GDI
Emulation
Page orientation
Interface port
Portrait or landscape
USB interface (USB1.1 Standard) /
IEEE1284-compliant bi-directional parallel interface (Only for printer)
As a part of our policy of continuous improvement, TOSHIBA reserves the right to make
design and specification changes for product improvement without prior notice. The
performance specification figures indicated are nominal values of production units. There
may be some deviations from these values in individual units.
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL EQUIPMENT
System configuration
A number of options are available for the copier which allow you to configure a copier system to meet your
particular needs. The options include the following.
Auto document feeder
(MR-2014)
250-sheet paper feed unit
(MY-1019)
Auto document feeder (MR-2014)
The auto document feeder (ADF) holds up to 30 originals for automatic feeding.
Part names
Original guides
Document feeder tray
Feeding roller cover
ADF exit area
ADF (Auto Document Feeder) is called SPF in the software included in the CD-ROM packed
with the machine.
APPENDIX
8-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Acceptable originals
Weight:
Size:
52 to 90 g/m2 (14 to 23.9 lbs.)
A5 to A4 (5-1/2" x 8-1/2" to 8-1/2" x 14")
Up to 30 sheets
Capacity:
Power supply
Weight
Drawn from the copier
Approx. 3 kg (6.6 lbs.)
Dimensions
498 mm (W) x 380 mm (D) x 110 mm (H)
(19.6" (W) x 15" (D) x 4.3" (H))
As a part of our policy of continuous improvement, TOSHIBA reserves the right to make
design and specification changes for product improvement without prior notice. The
performance specification figures indicated are nominal values of production units. There
may be some deviations from these values in individual units.
Using the ADF
1. Make sure that no original is left on the original table.
2. Adjust the original guides to the size of originals.
3. Set the originals face up in the document feeder tray.
•
•
•
•
•
Before feeding originals in the document feeder tray, be sure to remove any staples or
paper clips from them.
Before placing curled or wavy originals into the document feeding tray, be sure to flatten
them. If not, original misfeeds may result.
The ADF ( ) indicator on the operation panel will light up. If this indicator does not light
up, the originals are not properly set or the ADF is not properly closed.
Badly damaged originals may misfeed in the ADF. It is recommended that such originals
be copied from the original table.
Special originals such as transparency film should not be fed through the ADF, but
should be placed directly on the original table.
8-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Stream feeding mode
The stream feeding mode allows easy operation of continuous copying from the ADF.
If the stream feeding mode has been enabled using user program No.4, the ADF ( ) indicator will blink
approximately 5 seconds after the last original has been fed by the ADF. While this indicator is blinking, any
new originals placed in the document feeder tray will be fed and copied automatically. If the stream feeding
mode has been disabled, the start (
) key must be pressed each time the originals are set even
immediately after completion of a copy run from the ADF. The default setting of the stream feeding mode is
„ON“. See page 4-3, USER PROGRAMS.
Misfeed in the ADF
An original misfeed may occur at one of three locations: if the misfed original is seen from the document
feeder tray, (A) in the document feeder tray; if the misfed original is not seen from the document feeder tray,
(B) in the exit area or (C) under the feeding roller. Remove the misfed original following the instructions for
each location.
(A)
Open the feeding roller cover and pull the original gently to the left and out from the document
feeder tray. Close the feeding roller cover. Open and close the original cover to clear the ADF
misfeed ( ) indicator. If the misfed original cannot be easily removed, proceed to (C) without pulling
the original forcibly from the document feeder tray.
(B)
Open the original cover and rotate the roller rotating knob to remove the misfed original from the
exit area. If the misfed original cannot be easily removed, proceed to (C).
APPENDIX
8-6
Download from Www.Somanuals.com. All Manuals Search And Download.
(C)
If the original does not move easily into the ADF exit area, remove it in the direction of the arrow
while rotating the knob.
A number may appear in the display after a minus sign, indicating the number of the
originals that must be returned to the document feeder tray.
Clear the misfeed and return the required number of originals. Then press the start (
key to resume copying.
)
250-SHEET PAPER FEED UNIT (MY-1019)
The paper feed unit (PFU) provides the convenience of increased paper capacity for the copier and a
greater choice of paper sizes readily available for copying.
Part names
Loading copy paper
The method of loading copy paper for the paper tray of the paper feed unit (PFU) is the same as for the
paper tray in the copier. See page 2-2.
The method of changing the copy paper size is also the same for the paper tray in the copier.
See page 2-4
Side cover
Tray
8-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Misfeed removal
The copier will stop when a misfeed occurs. The misfeed (
display.
) indicator blinks or
blinks in the
Open the lower side cover (under the bypass tray) and remove the misfed paper.
1If
blinks and the misfed paper is not seen from the area of the lower side cover, pull out
the lower paper tray and remove the misfed paper.Then close the lower paper tray.
Close the lower side cover.
2
3
Close the side cover by pressing the round projections near the side cover open button. The
misfeed (
) indicator will go out and the start (
) key will light up.
Specifications
Copy paper size
Paper weight
Paper capacity
Weight
A5 to A4 (5-1/2" x 8-1/2" to 8-1/2" x 14")
56 to 80 g/m2 (15 lbs. to 21 lbs.)
One paper tray with capacity for 250 sheets of 80 g/m2 (21 lb.) bond paper
Approx. 3 kg (6.6 lbs.)
Dimensions
498 mm (W) x 395 mm (D) x 88 mm (H)
(19.6" (W) x 15.6" (D) x 3.5" (H))
Power supply
Drawn from the copier
As a part of our policy of continuous improvement, TOSHIBA reserves the right to make
design and specification changes for product improvement without prior notice. The
performance specification figures indicated are nominal values of production units. There
may be some deviations from these values in individual units.
APPENDIX
8-8
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
A
D
Acrobat Reader .................................... 7-26, 7-27 Dark key ..................................................... 1-4, 3-7
Alarm indicator
Developer replacement required
Developer replacement required
indicator ............................................. 1-4, 6-3, 6-7
indicator........................................ 1-4, 6-3, 6-7 Desktop Document Manager ........................... 7-2
Maintenance indicator................. 1-4, 6-3, 6-7 Developer required .......................................... 6-7
Misfeed indicator ......................... 1-4, 6-3, 6-4 Display .............................................................. 1-4
Toner cartridge replacement required
Displaying total number of copies ................... 4-4
indicator ............................................. 1-4, 5-2, 6-3
Appendix ........................................................... 8-2
Auto clear time .................................................. 4-3
Auto power shut-off mode ................................ 4-3
Automatic exposure adjustment ...................... 3-7
E
Exposure adjustment ....................................... 3-6
Exposure mode indicator .......................... 1-4, 3-6
Exposure mode selector key .................... 1-4, 3-6
B
Before installation ............................................ 7-3
Button Manager .......................................7-2, 7-18
Bypass ............................................................... 1-3
Bypass feed ...................................................... 2-6
Bypass tray guides ........................................... 1-3
F
Flow of installation............................................ 7-4
Front cover ........................................................ 1-3
Fusing unit release lever .......................... 1-3, 6-5
H
C
Handle ............................................................... 1-3
Hardware and software
Cautions
Handling .......................................................... 7
Label ................................................................ 6
Laser ................................................................ 7
Using................................................................ 6
Charger cleaner......................................... 1-3, 5-6
Cleaning the unit
Cabinet ........................................................ 5-5
Original cover .............................................. 5-5
Original table............................................... 5-5
Transfer charger .......................................... 5-6
Clear key ............................................ 1-4, 3-6, 4-4
Connecting the interface cable
Parallel interface cable ............................ 7-30
USB interface cable.................................. 7-29
Conventions used in the manual .................... 1-2
Copy flow .......................................................... 3-2
Copy quantity .................................................... 3-6
Copy quantity key .............................. 1-4, 3-6, 4-3
Copy ratio display key ............................... 1-4, 3-8
Copy ratio selector indicator..................... 1-4, 3-8
Copy ratio selector key.............................. 1-4, 3-8
requirements ..................................................... 7-3
How to print ..................................................... 7-16
How to use the online manual....................... 7-26
I
Indicators on the operation panel ................. 7-15
Initial settings of operation panel .................... 3-4
Installing the software ...................................... 7-2
Interface
Parallel interface....................................... 7-30
USB interface ............................................ 7-29
Interrupt copying............................................. 7-17
Introduction ....................................................... 1-2
L
Light and dark indicator ............................ 1-4, 3-6
Light key ..................................................... 1-4, 3-7
Loading paper .................................................. 2-2
Loading the paper tray ..................................... 2-4
8-9
Download from Www.Somanuals.com. All Manuals Search And Download.
M
S
Maintenance indicator ...................... 1-4, 6-3, 6-7 Scanner driver .................................................. 7-2
Making copies................................................... 3-2 Scanner indicator ....................................1-4, 7-15
MFP driver
SCANNER key.........................................1-4, 7-22
Print Status Window ................................... 7-2 Scanning from your computer ....................... 7-23
Printer driver................................................ 7-2 Scanning with the “Scanner and
Scanner driver............................................. 7-2 Camera Wizard”.............................................. 7-25
Misfeed indicator ............................... 1-4, 6-3, 6-4 Side cover ......................................................... 1-3
Misfeed removal
Side cover open button .................................... 1-3
Fusing area ................................................. 6-5 Software for the TOSHIBA Personal MFP
Paper feed area .......................................... 6-5 series ................................................................. 7-2
Transport area ............................................. 6-6 Specifications.................................................... 8-2
Multi-bypass............................................... 1-3, 2-6 Start indicator ...........................................1-4, 7-15
Start key ............................................. 1-4, 3-2, 4-4
Status indicators ............................................... 6-3
N
Name
T
Operation panel .......................................... 1-4
Part names .................................................. 1-3 Toner cartridge........................................... 1-3, 5-2
Toner cartridge replacement............................ 5-2
Toner cartridge replacement
indicator ............................................. 1-4, 5-2, 6-3
Transfer charger......................................... 1-3, 5-6
O
ONLINE indicator .....................................1-4, 7-15
Troubleshooting ................................................ 6-2
ONLINE key .............................................1-4, 7-15
Troubleshooting the unit .................................. 6-2
Online manual ................................................ 7-26
Opening the printer driver .............................. 7-16
Opening the scanner driver ........................... 7-23
Operation panel ......................................... 1-3, 1-4
U
Original placement ........................................... 3-5 USB interface cable ....................................... 7-29
Original table .................................................... 1-3 Using other installed drivers.......................... 7-28
Using the manual ............................................. 1-2
Using the printer mode................................... 7-16
Using the scanner mode ................................ 7-18
Using the TOSHIBA TWAIN ............................ 7-23
P
Paper ................................................................. 2-2
Paper feed location indicators......................... 1-4
Paper output tray .............................................. 1-3
Paper output tray extension ...................... 1-3, 3-2
Z
Paper tray................................................... 1-3, 2-4 ZOOM indicator .......................................... 1-4, 3-8
Parallel interface cable ........................ 7-29, 7-30 ZOOM key .................................................. 1-4, 3-8
Photo copying ................................................... 3-6
Power cord socket ............................................ 1-3
Power off ........................................................... 3-4
Power on ........................................................... 3-3
Power save indicator ...............................1-4, 7-15
Power switch .............................................. 1-3, 3-3
Preheat mode ................................................... 4-3
Proper storage ...................................................... 7
R
Reduction/enlargement/zoom ......................... 3-8
APPENDIX
8-10
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE LICENSE
PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY USING THE
SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE.
1. License.
The application, demonstration, system and other software accompanying this License, whether on disk, in read only
memory, or on any other media (the “Software”) and related documentation are licensed to you by TOSHIBA. You own
the disk on which the Software is recorded but TOSHIBA and/or TOSHIBA’S Licensors retain title to the Software and
related documentation. This License allows you to use the Software on one or more computers connected to a single
printer and make one copy of the Software in machine-readable form for backup purposes only. You must reproduce on
such copy the TOSHIBA copyright notice, the copyright notice of TOSHIBA’S Licensors and any other proprietary
legends of TOSHIBA and/or its Licensors that were on the original copy of the Software. You may also transfer all your
license rights in the software, the backup copy of the Software, the related documentation and a copy of this License to
another party, provided the other party reads and agrees to the terms and conditions of this License.
2. Restrictions.
The Software contains copyrighted material, trade secrets and other proprietary material which is owned by TOSHIBA
and/or its Licensors and in order to protect them you may not decompile, reverse engineer, disassemble or otherwise
reduce the Software to a human-perceivable form. You may not modify, network, rent, lease, loan, distribute or create
derivative works based upon the Software in whole or in part. You may not electronically transmit the Software from one
computer to another or over a network.
3. Termination.
This license is effective until terminated. You may terminate this License at any time by destroying the Software and
related documentation and all copies thereof. This License will terminate immediately without notice from TOSHIBA
and/or TOSHIBA’S Licensors if you fail to comply with any provision of this License. Upon termination you must
destroy the Software and related documentation and all copies thereof.
4. Export Law Assurances.
You agree and certify that neither the Software nor any other technical data received from TOSHIBA, nor the direct
product thereof, will be exported outside the United States except as authorized and as permitted by the laws and
regulations of the United States. If the Software has been rightfully obtained by you outside of the United States, you agree
that you will not re-export the Software nor any other technical data received from TOSHIBA, nor the direct product
thereof, except as permitted by the laws and regulations of the United States and the laws and the regulation of the
jurisdiction in which you obtained the Software.
5. Government End Users.
If you are acquiring the Software on behalf of any unit or agency of the United States Government, the following
provisions apply. The Government agrees:
(i) if the Software is supplied to the Department of Defense (DoD), the Software is classified as “Commercial
Computer Software” and the Government is acquiring only “restricted rights” in the Software and its documentation
as that term is defined in Clause 252.227-7013 (c)(1) of the DFARS; and
(ii) if the Software is supplied to any unit or agency of the United States Government other than DoD, the Government’s
rights in the Software and its documentation will be as defined in Clause 52.227-19 (c)(2) of the FAR or, in the case
of NASA, in Clause 18-52.227-86 (d) of the NASA Supplement to the FAR.
6. Limited Warranty on Media.
TOSHIBA warrants the disks on which the Software is recorded to be free from defects in materials and workmanship
under normal use for a period of ninety (90) days from the date of purchase as evidenced by a copy of the receipt. The
entire liability of TOSHIBA and/or its Licensors and your exclusive remedy will be replacement of the disk which fails to
meet the limited warranty provided by this Clause 6. A disk will be replaced when it is returned to TOSHIBA or a
TOSHIBA authorized representative with a copy of the receipt. TOSHIBA will have no responsibility to replace a disk
damaged by accident, abuse or misapplication.
ANY IMPLIED WARRANTIES ON THE DISKS, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO NINETY
(90) DAYS FROM THE DATE OF DELIVERY. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.
8-11
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Disclaimer of Warranty on Software.
You expressly acknowledge and agree that use of the Software is at your sole risk. The software and related documentation
are provided “AS IS” and without warranty of any kind and TOSHIBA and TOSHIBA’S Licensor(s) (for the purpose of
provisions 7 and 8, TOSHIBA and TOSHIBA’S Licensor(s) shall be collectively referred to as “TOSHIBA”) EXPRESSLY
DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TOSHIBA DOES NOT
WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET YOUR REQUIREMENTS, OR
THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE, OR THAT DEFECTS
IN THE SOFTWARE WILL BE CORRECTED. FURTHERMORE, TOSHIBA DOES NOT WARRANT OR MAKE ANY
REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE SOFTWARE OR RELATED
DOCUMENTATION IN TERMS OF THEIR CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. NO
ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY TOSHIBA OR A TOSHIBA AUTHORIZED
REPRESENTATIVE SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS
WARRANTY. SHOULD THE SOFTWARE PROVE DEFECTIVE, YOU (AND NOT TOSHIBA OR A TOSHIBA
AUTHORIZED REPRESENTATIVE) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION, SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO THE
ABOVE EXCLUSION MAY NOT APPLY TO YOU.
8. Limitation of Liability.
UNDER NO CIRCUMSTANCES INCLUDING NEGLIGENCE, SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OR INABILITY TO USE THE
SOFTWARE OR RELATED DOCUMENTATION, EVEN IF TOSHIBA OR A TOSHIBA AUTHORIZED
REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME JURISDICTIONS DO
NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
In no event shall TOSHIBA’S total liability to you for all damages, losses, and causes of action (whether in contract, tort
(including negligence) or otherwise) exceed the amount paid by you for the Software.
9. Controlling Law and Severability.
For a portion of the Software related with Apple Macintosh and Microsoft Windows, this license shall be governed by and
construed in accordance with the laws of the state of California and Washington, respectively. If for any reason a court
of competent jurisdiction finds any provision of this License, or portion thereof, to be unenforceable, that provision of
the License shall be enforced to the maximum extent permissible so as to effect the intent of the parties, and the
remainder of this License shall continue in full force and effect.
10. Complete Agreement.
This License constitutes the entire agreement between the parties with respect to the use of the Software and related
documentation, and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding such
subject matter. No amendment to or modification of this License will be binding unless in writing and signed by a duly
authorized representative of TOSHIBA.
APPENDIX
8-12
Download from Www.Somanuals.com. All Manuals Search And Download.
2231253EN
estudio120_150_EN.pdf
estudio120_150 copier Manual EN
Toshiba Tec Germany Imaging Systems GmbH
Carl-Schurz-Str. 7
41460 Neuss
Telefon +49/(0)2131/1245-0
Fax +49/(0)2131/1245-402
Download from Www.Somanuals.com. All Manuals Search And Download.
|