Installation Instructions
for
Thermador® Microwave MBY
(Sold Separately)
Built-InTrim Kits • Models MT27 & MT30
SENSOR
REHEAT
SENSOR
COOK
POWER
LEVEL
POP
CORN
1
4
2
3
5
8
0
6
9
7
TIMER
CLOCK
MORE
/LESS
QUICK FUNCTION
MIN KEY
SERVING
/WEIGHT
KEEP
WARM
TURBO
DEFROST
STOP/RESET
START
Please Read this entire manual before proceeding:
IMPORTANT: Local codes vary. Installation, electrical connections, circuit breakers
and grounding must comply with all applicable codes. Save these
instructions for the Local Electrical Inspector's use.
INSTALLER:
Please leave these Installation Instructions with this unit for the
owner.
OWNER:
Please retain these instructions for future reference.
Disconnect power at the breaker before installing.
WARNING:
Table of Contents
Step 1: Unpacking ............................................. 2
Step 2: Cabinet Preparation ........................... 3
Step 3: Electrical Installation........................... 3
Step 4: Installing theTrim Kit.......................... 4
Step 5: Installing the Microwave Oven ......... 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Cabinet Preparation
• The cabinet cut out dimensions are shown in
Figure 1.
• Your microwave oven can be installed into a
cabinet or wall by itself or above any of the
following:Thermador wall ovens C271, C301,
CM301, S301, SC301, CJ301 or Thermador
Warming Drawers WD 27 and WD 30 (See
Figure 2).
• It is good practice, when microwave oven is
installed at the end of a cabinet run, adjacent
to a perpendicular wall or cabinet door, to al-
low at least 1/4" space between the side of
the trim and the wall/door
• Outlet should be in the shaded area as indi-
cated in Figure 1.
Dimensions
Trim Kits
Width (B)
28-1/2
25-1/2
"
"
1/16
1/16
MT30B; MT30W; MT30S
MT27B; MT27W; MT27S
Figure 1.
Height (A)
Depth (C)
17" 1/16
AllTrim Kits
AllTrim Kits
1
24"
/8
➝
14"
➝
4"
A
➛
Outlet should be in
the shaded area.
4"
Top of
microwave
shelf
B
C
-3
}
1 /4
"
Microwave
Cutout
Step 3: Electrical
(45 mm)
Installation
The Thermador micro-
wave oven is equipped with
a grounded cord. The wall
receptacle must be in-
stalled and grounded in ac-
cordance with the national
electrical code. Also, elec-
trical connections and
grounding must comply
with all applicable local
codes.
The electrical require-
ments for a separate circuit
serving only this micro-
wave oven are: 120v,60Hz,
15amp.
Thermador
single wall
oven cutout
1-1/2
(38 mm)
}
"
Microwave
cutout
Warming
Drawer
cutout
Figure 2.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Installing theTrim Kit
A. Position the 2 vertcatrim brackets uing the tempate as hown on Figure 3.
Trim Brackets
Figure 3.
Centerline
cutout
Notch to mark
➝
Screws #8 x 1/4
the center line of
the cutout.
.
➝
Template
Template is used to locate the positions of the left and
right trim brackets with respect to the cut out. The
trims are secured with (3) screws each and the tem-
plate is discarded after.
Mark the center line of the cut out using the template.
Screws #8 x 1/4
Figure 4.
CENTERLINE MARK
B. Position base pan on cabinet shelf with respect to the center line as shown on Figure
4. The front end of pan should align flush with the front edge of the shelf. Fasten base
pan to shelf with 2 screws #8 x 1/4.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5: InstallingThe Microwave Oven (Figure 5)
4. Remove and retain outer case screw at rear
Note:The four (4) ducts have a plastic cover-
ing that must be removed prior to installing
these ducts onto the microwave section.These
ducts have sharp edges.Be careful when han-
dling.
of the oven (right side)
5. Install the grommet and the electrical cord
of the microwave in the receiving hole pro-
vided in the rear intake duct, and position
this duct on rear of the oven (right side).
Fasten with outer case screw.
1. Remove and retain outer case screw at rear
of the oven (left side)
7. Position top intake duct on upper (right side)
of oven and fasten it together with rear in-
take duct by using 4 screws #8x1/4
2. Position upper exhaust duct on top (Hinge
Side) of oven. Fasten with outer case screw
3. Position side duct on left side of oven and
fasten it together with upper exhaust duct
by using 2 screw
8. Apply tape along all ducts flanges. Press tape
to secure properly.
Outer
case
screw
Upper
Exhaust
duct
Top
intake
duct
Screw
#8x1/4
Side
duct
Rear
intake
duct
.
.
Grommet
Screw
#8x1/4
.
Outer case
screw
Microwave
Oven
Figure 5.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5: InstallingThe Microwave Oven (continued)
9. Remove the left side vertical trim bracket (3
screws) (for MT27 only)
10. Slide the assembled microwave oven in the
prepared cabinet cutout. Plug the electrical
cord in the wall receptacle (ask help from
another person). Align the microwave oven
legs to the pan channel holes (Figure 6).
11. Install back the left side vertical trim bracket.
(3 screws)
Figure 6.
12. Snap on the frame trim with the “Therma-
dor Logo under the microwave door button.
(Figure 7)
FrameTrim
13. Install the turntable and the turntable sup-
port inside of the microwave oven.
14. Follow the “Care & Use” manuals instruc-
tions for operation
Figure 7.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Thermador reserves the right to change specifications or design without notice. Some models are certified for
use in Canada. Thermador is not responsible for products which are transported from the United States for
use in Canada. Check with your local Canadian distributor or dealer. Thermador, 5551 McFadden Avenue,
Huntington Beach, CA 92649.
For the most up to date critical installation dimensions by fax,use your fax handset and call 702/833-3600. Use
code #8030.
5551 McFadden Avenue, Huntington Beach, CA 92649 • 800/735-4328
ECO 12596 • 16-10-969B • © 2000 BSH Home Appliances Corp. • Litho Date: 8/01
Download from Www.Somanuals.com. All Manuals Search And Download.
|