4-253-072-11(2)
FM Stereo
FM/AM Receiver
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the serial
number in the space provided below. Refer to them whenever you call upon your
Sony dealer regarding this product.
Model No.
Serial No.
STR-DE897
©2004 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
Note for the supplied remote
For RM-PG413
• The instructions in this manual is for model
at the lower right corner of the front panel.
• The instructions in this manual describe the controls
on the receiver. You can use the controls on the
supplied remote if they have the same or similar
names as those on the receiver. For details on the use
of your remote, see pages 44–53.
The 2ND button on the remote is not available
for receiver operation.
About area codes
The area code of the receiver you purchased is
shown on the lower portion of the rear panel (see
the illustration below).
FRONT
A
R
R
L
L
+
–
–
+
FRONT
B
SPEAKERS
URROUND
L
–
+
–
+
L
ROUND BACK
CENTER
SPEAKERS
4-XXX-XXX-XX AA
Area code
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are
trademarks of Dolby Laboratories.
**“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are
trademarks of Digital Theater Systems, Inc.
3GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Advanced Adjustments and
1: Check how to hookup your
components.......................................5
1a: Connecting components with
only analog audio jacks............12
2: Connecting the antennas...................14
4: Connecting the AC power cord ........17
digital components ......................... 35
Other Operations
Naming preset stations and inputs........ 39
Listening to the sound in another
Amplifier Operation
— MULTI CH IN
Remote button description.................... 44
Selecting the command mode of the
Programming the remote ...................... 48
Learning the commands of your
Enjoying Surround Sound
Using only the front speakers ...............28
— AUTO FORMAT DIRECT
Selecting a sound field..........................30
Selecting the surround back decoding
mode ...............................................32
— SURR BACK DECODING
Troubleshooting.................................... 55
Specifications ....................................... 58
List of button locations and reference
pages............................................... 60
Index..................................................... 61
4GB
Download from Www.Somanuals.com. All Manuals Search And Download.
.
Getting Started
1: Check how to hookup your components
Steps 1a through 1c beginning on page 7 describe how to hook up your components to this receiver.
Before you begin, refer to “Connectable components” below for the pages which describe how to
connect each component.
After hooking up all your components, proceed to “2: Connecting the antennas” (page 14).
Connectable components
Component to be connected
DVD player
Page
a)
With digital audio output
7–8
b)
With multi channel audio output
10–11
7–8
c)
With analog audio output only
TV monitor
With component video input
With S-video or composite video input only
Satellite tuner
With digital audio output
With analog audio output only
Super Audio CD/CD player
With digital audio output
d)
8 or 11
13
a)
7–8
7–8
c)
a)
9
b)
With multi channel audio output
10
12
c)
With analog audio output only
MD/Tape deck
With digital audio output
With analog audio output only
Analog disc turntable
a)
9
c)
12
12
10
13
Multi channel decoder
VCR, camcorder, video game, etc.
a)
Model with a DIGITAL OPTICAL OUTPUT or DIGITAL COAXIAL OUTPUT jack, etc.
Model with a MULTI CH OUTPUT jacks, etc. This connection is used to output the audio decoded by the
component’s internal multi channel decoder through this receiver.
b)
c)
d)
Model equipped only with AUDIO OUT L/R jacks, etc.
Model with component video (Y, P /C /B-Y, P /C /R-Y) input jacks.
B
B
R
R
continued
5GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Required cords
The hookup diagrams on the subsequent pages assume the use of the following optional connection
cords (A to H) (not supplied).
A Audio cord
F Coaxial digital cord
White (L)
Red (R)
G Monaural audio cord
Black
B Audio/video cord
Yellow (video)
White (L/audio)
Red (R/audio)
Tip
Audio cord A can be torn into two monaural audio
cords G.
C Video cord
Yellow
H Component video cord
Green
Blue
D S-video cord
Red
E Optical digital cord
Notes
• Turn off the power to all components before making any connections.
• Be sure to make connections firmly to avoid hum and noise.
• When connecting an audio/video cord, be sure to match the color-coded pins to the appropriate jacks on the
components: yellow (video) to yellow; white (left, audio) to white; and red (right, audio) to red.
• When connecting optical digital cords, insert the cord plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
If you have Sony components with CONTROL A1II jacks
See “CONTROL A1II Control System” on page 42.
6GB
Download from Www.Somanuals.com. All Manuals Search And Download.
.
1a: Connecting components with digital audio output jacks
Hooking up a DVD player or satellite tuner
For details on the required cords (A–H), see page 6.
1 Connect the audio jacks.
DVD player
OUTPUT
AUDIO
OUT
OUTPUT
L
DIGITAL
COAXIAL
R
F
A
DIGITAL
(ASSIGNABLE)
ANTENNA
OPTICAL
TV/SAT
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
IN
AM
MD/
TAPE
IN
MD/
TAPE
OUT
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
L
L
CTRL
L
MONITOR A1 II
COM
SA-CD/
CD
IN
R
R
DVD
IN
R
SUB
AUDIO IN
AUDIO IN
AUDIO OUT AUDIO IN
AUDIO OUT AUDIO IN
WOOFER
SIGNAL GND
TV/SAT DVD
VIDEO 2
VIDEO 1
L
PRE OUT
SA-CD/
CD
L
L
L
L
IN
COAXIAL
CENTER
CENTER
L
R
R
R
R
R
R
SUB
SURR
BACK
SUB
IN
IN
OUT
IN
FRONT SURROUND
OUT
WOOFER
FRONT SURROUND
MULTI CH IN 1
WOOFER
PHONO SA-CD
/CD
MD/TAPE
MULTI CH IN 2
2ND ZONE
E
A
OUTPUT
DIGITAL
OPTICAL
OUTPUT
AUDIO
OUT
L
R
Satellite tuner
Note
You can also listen to the sound of your TV by connecting your TV’s audio output jacks to the TV/SAT AUDIO IN
jacks on the receiver. In this case, do not connect the TV’s video output jack to the TV/SAT VIDEO IN jack on the
receiver.
continued
7GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connect the video jacks.
The following illustration shows how to connect a satellite tuner and a DVD player with
COMPONENT VIDEO (Y, P /C /B-Y, P /C /R-Y) output jacks. Connecting a TV with component
B
R
B
R
video input jacks allows you to enjoy higher quality video.
TV monitor
Satellite tuner
OUTPUT
INPUT
COMPONENT
B/CB/B–Y
OUTPUT
VIDEO
OUTPUT
VIDEO
INPUT
VIDEO
INPUT
VIDEO
COMPONENT
S
S
P
R/CR/R–Y
P
B/CB/B–Y
Y
P
R/CR/R–Y
P
Y
C
D
H
C
D
H
DIGITAL
(ASSIGNABLE)
ANTENNA
Y
OPTICAL
TV/SAT
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
IN
P
B/CB
AM
/B–Y
MD/
TAPE
IN
P
R/CR
/R–Y
MD/
TAPE
OUT
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
DVD
IN
MONITOR
OUT
L
L
CTRL
L
MONITOR A1 II
COMPONENT VIDEO
SA-CD/
CD
IN
SU
R
R
R
DVD
IN
R
SUB
AUDIO IN
AUDIO IN
AUDIO OUT AUDIO IN
AUDIO OUT AUDIO IN
WOOFER
SIGNAL GND
TV/SAT DVD
VIDEO 2
VIDEO 1
L
PRE OUT
SA-CD/
CD
L
L
L
L
+
–
IN
COAXIAL
CENTER
CENTER
L
R
R
R
R
R
R
R
SUB
SURR
BACK
SUB
SURR
S
IN
IN
OUT
IN
FRONT SURROUND
OUT
WOOFER
FRONT SURROUND
MULTI CH IN 1
WOOFER
PHONO SA-CD
/CD
MD/TAPE
MULTI CH IN 2
2ND ZONE
C
D
H
OUTPUT
OUTPUT
VIDEO
OUTPUT
COMPONENT
S
VIDEO
P
R/CR/R–Y
PB/CB/B–Y
Y
DVD player
Tips
• When using the S-video jacks instead of the video jacks, your monitor must also be connected via an S-video jack.
S-video signals are on a separate bus from the video signals and will not be output through the video jacks.
• When the component is equipped with S-video jacks, you can connect the component to the S-video jacks on this
receiver.
• (Models of area code U, CA only) This receiver can convert standard video signals to S-video signals for output
from the MONITOR S-VIDEO OUT jacks.
8GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Hooking up an MD/Tape deck or a Super Audio CD/CD player
For details on the required cords (A–H), see page 6.
MD/Tape deck
INPUT OUTPUT
LINE
LINE
DIGITAL
L
OPTICAL
IN
OUT
R
E
E
A
A
OUT
IN
OUT
IN
DIGITAL
(ASSIGNABLE)
ANTENNA
OPTICAL
TV/SAT
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
IN
AM
MD/
TAPE
IN
MD/
TAPE
OUT
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
L
L
CTRL
L
MONITOR A1 II
COM
SA-CD/
CD
IN
R
R
DVD
IN
R
SUB
AUDIO IN
AUDIO IN
AUDIO OUT AUDIO IN
AUDIO OUT AUDIO IN
WOOFER
SIGNAL GND
TV/SAT DVD
VIDEO 2
VIDEO 1
L
PRE OUT
SA-CD/
CD
L
L
L
L
IN
COAXIAL
CENTER
CENTER
L
R
R
R
R
R
R
SUB
SURR
BACK
SUB
IN
IN
OUT
IN
FRONT SURROUND
OUT
WOOFER
FRONT SURROUND
MULTI CH IN 1
WOOFER
PHONO SA-CD
/CD
MD/TAPE
MULTI CH IN 2
2ND ZONE
E
F
A
DIGITAL
OUTPUT
OUTPUT
LINE
DIGITAL
OPTICAL
OUT
COAXIAL
L
R
Super Audio CD/
If you want to connect several digital components, but cannot find an
unused input
See “Assigning the audio input” (page 34).
Tip
All the digital audio jacks are compatible with 32 kHz, 44.1 kHz, 48 kHz and 96 kHz sampling frequencies.
Notes
• You cannot make digital recordings of digital multi channel surround signals.
• It is not possible to record analog signals to components connected to the MD/TAPE OUT, VIDEO 1 OUT or
VIDEO 2 OUT jacks if you make only digital connections. Likewise, you cannot record digital signals if you make
only analog connections. To record analog signals, make analog connections. To record digital signals, make
digital connections.
• The sound is not output when you play a Super Audio CD on the Super Audio CD player connected to the
SA-CD/CD OPTICAL IN or SA-CD/CD COAXIAL IN jack on this receiver. Connect to the analog input jacks
(SA-CD/CD IN jacks). Refer to the operating instructions supplied with the Super Audio CD player.
9GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1b: Connecting components with multi channel output
jacks
1 Connect the audio jacks.
If your DVD or Super Audio CD player is equipped with multi channel output jacks, you can connect
it to this receiver’s MULTI CH IN 1/MULTI CH IN 2 jacks to enjoy the multi channel sound.
Alternatively, the multi channel input jacks can be used to connect an external multi channel decoder.
For details on the required cords (A–H), see page 6.
DIGITAL
(ASSIGNABLE)
ANTENNA
OPTICAL
TV/SAT
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
IN
AM
MD/
TAPE
IN
MD/
TAPE
OUT
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
L
L
CTRL
L
MONITOR A1 II
COM
SA-CD/
CD
IN
R
R
DVD
IN
R
SUB
AUDIO IN
AUDIO IN
AUDIO OUT AUDIO IN
AUDIO OUT AUDIO IN
WOOFER
SIGNAL GND
TV/SAT DVD
VIDEO 2
VIDEO 1
L
PRE OUT
SA-CD/
CD
L
L
L
L
IN
COAXIAL
CENTER
CENTER
L
R
R
R
R
R
R
SUB
SURR
BACK
SUB
IN
IN
OUT
IN
FRONT SURROUND
OUT
WOOFER
FRONT SURROUND
MULTI CH IN 1
WOOFER
PHONO SA-CD
/CD
MD/TAPE
MULTI CH IN 2
2ND ZONE
A
A
G
G
L
CENTER
R
SUB
WOOFER
FRONT SURROUND
MULTI CH OUT
DVD player,
Super Audio CD player,
Multi channel decoder, etc.
Tips
• This connection also allows you to enjoy software with multi channel audio recorded in formats other than the
Dolby Digital and DTS.
• Make connections to either the MULTI CH IN 1 or MULTI CH IN 2 jacks according to the number of audio output
jacks of the component.
Note
When you make connections to the MULTI CH IN 1 or MULTI CH IN 2 jacks, you will need to adjust the level of
the surround speakers and sub woofer using the controls on the connected component.
10GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connect the video jacks.
The following illustration shows how to connect a DVD player with COMPONENT VIDEO (Y,
P /C /B-Y, P /C /R-Y) output jacks. Connecting a TV with component video input jacks allows you
B
B
R
R
to enjoy higher quality video.
DVD player
TV monitor
OUTPUT
COMPONENT
R/CR/R–Y B/CB/B–Y
INPUT
OUTPUT
VIDEO
OUTPUT
INPUT
VIDEO
INPUT
VIDEO
COMPONENT
S
VIDEO
S
P
P
Y
P
R/CR/R–Y
P
B/CB/B–Y
Y
C
D
H
C
D
H
DIGITAL
(ASSIGNABLE)
ANTENNA
Y
OPTICAL
TV/SAT
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
IN
P
B/CB
AM
/B–Y
MD/
TAPE
IN
P
R/CR
/R–Y
MD/
TAPE
OUT
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
DVD
IN
MONITOR
OUT
L
L
CTRL
L
MONITOR A1 II
COMPONENT VIDEO
SA-CD/
CD
IN
SU
R
R
R
DVD
IN
R
SUB
AUDIO IN
AUDIO IN
AUDIO OUT AUDIO IN
AUDIO OUT AUDIO IN
WOOFER
SIGNAL GND
TV/SAT DVD
VIDEO 2
VIDEO 1
L
PRE OUT
SA-CD/
CD
L
L
L
L
+
–
IN
COAXIAL
CENTER
CENTER
L
R
R
R
R
R
R
R
SUB
SURR
BACK
SUB
SURR
S
IN
IN
OUT
IN
FRONT SURROUND
OUT
WOOFER
FRONT SURROUND
MULTI CH IN 1
WOOFER
PHONO SA-CD
/CD
MD/TAPE
MULTI CH IN 2
2ND ZONE
Tips
• When using the S-video jacks instead of the video jacks, your monitor must also be connected via an S-video jack.
S-video signals are on a separate bus from the video signals and will not be output through the video jacks.
• When the component is equipped with S-video jacks, you can connect the component to the S-video jacks on this
receiver.
• (Models of area code U, CA only) This receiver can convert standard video signals to S-video signals for output
from the MONITOR S-VIDEO OUT jacks.
11GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1c: Connecting components with only analog audio jacks
Hooking up audio components
For details on the required cords (A–H), see page 6.
Turntable
A
DIGITAL
(ASSIGNABLE)
ANTENNA
OPTICAL
TV/SAT
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
IN
AM
MD/
TAPE
IN
MD/
TAPE
OUT
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
L
L
CTRL
L
MONITOR A1 II
CO
SA-CD/
CD
IN
R
R
DVD
IN
R
SUB
AUDIO IN
AUDIO IN
AUDIO OUT AUDIO IN
AUDIO OUT AUDIO IN
WOOFER
SIGNAL GND
TV/SAT DVD
VIDEO 2
VIDEO 1
L
PRE OUT
SA-CD/
CD
L
L
L
L
IN
COAXIAL
CENTER
CENTER
L
R
R
R
R
R
R
SUB
SURR
BACK
SUB
IN
IN
OUT
IN
FRONT SURROUND
OUT
WOOFER
FRONT SURROUND
MULTI CH IN 1
WOOFER
PHONO SA-CD
/CD
MD/TAPE
MULTI CH IN 2
2ND ZONE
OUT
IN
A
A
A
OUTPUT
LINE
INPUT OUTPUT
LINE LINE
L
L
R
R
Super Audio CD/CD
player
MD/Tape deck
Note
If your turntable has a ground wire, connect it to the U SIGNAL GND terminal.
12GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Hooking up video components
If you connect your TV to the MONITOR jacks, you can watch the video from the selected input
(page 22). For details on the required cords (A–H), see page 6.
VCR
INPUT OUTPUT
VIDEO
IN
VIDEO
OUT
TV monitor
AUDIO
OUT
AUDIO
IN
INPUT
VIDEO
L
INPUT
S
VIDEO
R
B
B
C
D
OUT
IN
DIGITAL
(ASSIGNABLE)
ANTENNA
Y
OPTICAL
TV/SAT
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
IN
P
B/CB
AM
/B–Y
MD/
TAPE
IN
P
R/CR
/R–Y
MD/
TAPE
OUT
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
DVD
IN
MONITOR
OUT
L
L
CTRL
L
MONITOR A1 II
COMPONENT VIDEO
SA-CD/
CD
IN
SU
R
R
R
DVD
IN
R
SUB
AUDIO IN
AUDIO IN
AUDIO OUT AUDIO IN
AUDIO OUT AUDIO IN
WOOFER
SIGNAL GND
TV/SAT DVD
VIDEO 2
VIDEO 1
L
PRE OUT
SA-CD/
CD
L
L
L
L
+
–
IN
COAXIAL
CENTER
CENTER
L
R
R
R
R
R
R
R
SUB
SURR
BACK
SUB
SURR
S
IN
IN
OUT
IN
FRONT SURROUND
OUT
WOOFER
FRONT SURROUND
MULTI CH IN 1
WOOFER
PHONO SA-CD
/CD
MD/TAPE
MULTI CH IN 2
2ND ZONE
To the
VIDEO 3
INPUT jacks
(Front panel)
OUT
IN
OUT
IN
B
B
B
D
D
INPUT OUTPUT
INPUT
VIDEO
OUTPUT
VIDEO
S
S
VIDEO
IN
VIDEO
OUT
AUDIO
OUT
AUDIO
IN
L
R
Camcorder or
video game
VCR
Tips
• When using the S-video jacks instead of the video jacks, your monitor must also be connected via an S-video jack.
S-video signals are on a separate bus from the video signals and will not be output through the video jacks.
• When the component is equipped with S-video jacks, you can connect the component to the S-video jacks on this
receiver.
• (Models of area code U, CA only) This receiver can convert standard video signals to S-video signals for output
from the MONITOR S-VIDEO OUT jacks.
13GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Connecting the antennas
Connect the supplied AM loop antenna and FM wire antenna.
AM loop antenna
(supplied)
FM wire antenna
(supplied)
DIGITAL
(ASSIGNABLE)
ANTENNA
OPTICAL
TV/SAT
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
IN
AM
MD/
TAPE
IN
MD/
TAPE
OUT
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
L
L
CTRL
L
MONITOR A1 II
COM
SA-CD/
CD
IN
R
R
DVD
IN
R
SUB
AUDIO IN
AUDIO IN
AUDIO OUT AUDIO IN
AUDIO OUT AUDIO IN
WOOFER
SIGNAL GND
TV/SAT DVD
VIDEO 2
VIDEO 1
L
PRE OUT
SA-CD/
CD
L
L
L
L
IN
COAXIAL
CENTER
CENTER
L
R
R
R
R
R
R
SUB
SURR
BACK
SUB
IN
IN
OUT
IN
FRONT SURROUND
OUT
WOOFER
FRONT SURROUND
MULTI CH IN 1
WOOFER
PHONO SA-CD
/CD
MD/TAPE
MULTI CH IN 2
2ND ZONE
*
*
The shape of the connector varies depending on the area code.
Notes
• To prevent noise pickup, keep the AM loop antenna away from the receiver and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
• Do not use the U SIGNAL GND terminal for grounding the receiver.
14GB
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Connecting speakers
Connect your speakers to the receiver. This receiver allows you to use a 7.1 channel speaker system.
To fully enjoy theater-like multi channel surround sound requires five speakers (two front speakers, a
center speaker, and two surround speakers) and a sub woofer (5.1 channel).
You can enjoy high fidelity reproduction of DVD software recorded in the Surround EX format if you
connect one additional surround back speaker (6.1 channel) or two surround back speakers (7.1
channel) (see “Selecting the surround back decoding mode” on page 32).
Example of 7.1 channel speaker system configuration
Center speaker
Front speaker (Right)
Surround speaker (Right)
Front speaker (Left)
Sub woofer
Surround speaker (Left)
Surround back speaker (Right)
Surround back speaker (Left)
Tips
• When you connect 6.1 channel speaker system, place the surround back speaker right behind the listening position
(see “When placing only one surround back speaker” illustration on page 19).
• Since the sub woofer does not emit highly directional signals, you can place it wherever you want.
continued
15GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Required cords
A Speaker cords (not supplied)
B Monaural audio cord (not supplied)
(+)
(–)
Black
Surround speaker
(Right)
Surrond speaker
(Left)
Front speaker
(Right)
Front speaker
(Left)
E
e E
e E
e E
e
A
A
A
A
SPEAKERS
FRONT B*
FRONT A
Y
R
R
L
L
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
P
B/CB
/B–Y
+
–
–
+
P
R/CR
/R–Y
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
DVD
IN
MONITOR
OUT
L
FRONT B
CTRL
MONITOR A1 II
COMPONENT VIDEO
SPEAKERS
SURROUND
R
L
R
SUB
AUDIO OUT AUDIO IN
WOOFER
VIDEO 1
L
PRE OUT
L
+
–
–
+
–
+
CENTER
L
R
R
R
L
R
SURR
BACK
SUB
SURROUND BACK
SPEAKERS
CENTER
OUT
FRONT SURROUND
MULTI CH IN 1
WOOFER
AC OUTLET
2ND ZONE
A
A
A
B
INPUT
AUDIO
IN
E
e E
e E
e
Surround back
speaker (Right)**
Surround back
speaker (Left)**
Center speaker
* If you have an additional front speaker system, connect them to the SPEAKERS FRONT B terminals. You can
select the front speakers you want to use with SPEAKERS (OFF/A/B/A+B) button. For details, see “Selecting the
speaker system” (page 40).
**If you connect only one surround back speaker, connect it to the SPEAKERS SURROUND BACK L terminals.
16GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• The AC OUTLET(s) on the rear of the receiver is a
switched outlet, which supplies power to the
connected component only while the receiver is
turned on.
4: Connecting the AC
power cord
• Make sure that the total power consumption of the
component(s) connected to the receiver’s AC
OUTLET(s) does not exceed the wattage stated on
the rear panel. Do not connect high-wattage
electrical home appliances such as electric irons,
fans, or TVs to this outlet. This may cause a
malfunction.
Setting the voltage selector
If your receiver has a voltage selector on the rear
panel, check that the voltage selector is set to the
local power supply voltage. If not, use a
screwdriver to set the selector to the correct
position before connecting the AC power cord to
a wall outlet.
Performing initial setup
operations
120V
240V
220V
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure.
This procedure can also be used to return
settings you have made to their factory defaults.
Use the buttons on the receiver for the operation.
VOLTAGE SELECTOR
1
2
Press ?/1 to turn off the receiver.
Connecting the AC power
cord
Hold down ?/1 for 5 seconds.
“PUSH ENTER” flashes in the display.
Connect the AC power cord to a wall outlet.
3
Press ENTER.
“MEMORY CLEARING” appears in the
display for a while, then “MEMORY
CLEARED” appears.
NT A
L
The following are reset to their factory
settings.
• All settings in the SET UP, LEVEL,
EQUALIZER and CUSTOMIZE menus.
• The sound field memorized for each
input and preset station.
–
+
L
b
To a wall
outlet
NT B
–
+
• All sound field parameters.
• All preset stations.
• All index names for inputs and preset
stations.
CENTER
AC OUTLET
• MASTER VOLUME –/+ is set to “VOL
MIN”.
• Input is set to DVD.
*
AC OUTLET
AC power cord
* The configuration, shape and number of AC outlets
vary according to the area code.
17GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x SUB WOOFER XXX
(Sub woofer selection)
5: Setting up the speakers
• YES
You can use the SET UP menu to set the size,
distance and location of the speakers connected
to this receiver.
If you connect a sub woofer, select “YES”.
• NO
If you did not connect a sub woofer, select
“NO”. The front speakers are automatically
set to “LARGE” and you cannot change this
setting. This activates the bass redirection
circuitry and outputs the LFE signals from
other speakers.
• In order to take full advantage of the Dolby
Digital bass redirection circuitry, we
recommend that you set the cut off frequency
on the sub woofer as high as possible.
1
2
Press ?/1 to turn on the receiver.
Press MAIN MENU repeatedly to select
“
SET UP ”.
3
Press or repeatedly to select the
parameter you want to adjust.
For details, see “Speaker setup parameters”
below.
Note
Some speaker setup items may appear dimmed in
the display. This means that they have been
adjusted automatically due to other speaker
settings or may not be adjustable.
x FRONT SP XXXXX
(Front speakers size)
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
• SMALL
4
5
The setting is entered automatically.
Note
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
front channel bass frequencies from the sub
woofer. When the front speakers are set to
“SMALL”, the center, surround and surround
back speakers are also automatically set to
“SMALL” (unless previously set to “NO”).
Press ENTER if you select the setting for “SP.
PATTERN X–X”.
Repeat steps 3 and 4 until you have set
all of the items that follow.
Speaker setup parameters
The initial settings are underlined.
x EASY SET UP XXX (Speaker easy setup)
x CTR SP XXXXX
• YES
(Center speaker size)
If you want to set up your speakers
automatically, select “YES”. You can select a
pre-defined speaker pattern (see the supplied
“Easy Setup Guide”).
• LARGE
If you connect a large speaker that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the center speaker
to “LARGE”.
• NO
If you want to adjust the settings of each
speaker manually, select “NO”.
• SMALL
x SP. PATTERN X–X
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
center channel bass frequencies from the front
(Speaker setup pattern)
When you select “EASY SET UP YES”, select
the speaker setup pattern. Turn –/+ to select the
speaker setup pattern and press ENTER to enter
the selection. Check your speaker pattern using
the supplied “Easy Setup Guide”.
a)
speakers (if set to “LARGE”) or sub woofer.
18GB
Download from Www.Somanuals.com. All Manuals Search And Download.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the sub woofer or other “LARGE”
speakers.
However, since bass sounds have a certain amount of
directionality, it is best not to cut them, if possible.
Therefore, even when using small speakers, you can
set them to “LARGE” if you want to output the bass
frequencies from that speaker. On the other hand, if
you are using a large speaker, but prefer not to have
“SMALL”.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE”. If there is not enough bass,
you can use the BASS parameter in the
EQUALIZER menu to boost the bass levels. To
adjust the bass, see page 37.
• NO
If you did not connect a center speaker, select
“NO”. The sound of the center channel will be
b)
output from the front speakers.
xSURR SP XXXXX
(Surround speakers size)
• LARGE
If you connect large speakers that will
effectively reproduce bass frequencies, select
“LARGE”. Normally, select “LARGE”.
However, if the front speakers are set to
“SMALL”, you cannot set the surround
speakers to “LARGE”.
• SMALL
If the sound is distorted, or you feel a lack of
surround effects when using multi channel
surround sound, select “SMALL” to activate
the bass redirection circuitry and output the
surround channel bass frequencies from the
sub woofer or other “LARGE” speakers.
• NO
x FRONT DIST. X.X m (XX ft.)
(Front speaker distance)
Initial setting: 3.0 m (10 ft.)
Lets you set the distance from your listening position
to the front speakers (A). You can adjust from 1.0
meter to 7.0 meters (3 to 23 feet) in 0.1 meter (1 foot)
steps.
If you did not connect surround speakers,
If both front speakers are not placed an equal distance
from your listening position, set the distance to the
closest speaker.
c)
select “NO”.
xSB SP XXXXXX
(Surround back speakers selection)
When placing only one surround back speaker
When the surround speakers are set to “NO”, the
surround back speakers are also automatically
set to “NO” and the setting cannot be changed.
• DUAL
B
A
A
30˚ 30˚
If you connect two surround back speakers,
select “DUAL”. The sound will be output to a
maximum of 7.1 channels.
100˚-120˚
100˚-120˚
C
C
• SINGLE
If you connect only one surround back
speaker, select “SINGLE”. The sound will be
output to a maximum of 6.1 channels.
• NO
D
When placing two surround back speakers
If you did not connect surround back speaker,
select “NO”.
(The angle E should be the same)
B
Tips
• a)–c) correspond to the following Dolby Pro Logic
modes
a) NORMAL
A
A
30˚ 30˚
100˚-120˚
100˚-120˚
b) PHANTOM
c) 3 STEREO
E
E
D
E
• The “LARGE” and “SMALL” settings for each
speaker determine whether the internal sound
processor will cut the bass signal from that channel.
D
continued
19GB
Download from Www.Somanuals.com. All Manuals Search And Download.
For example, setting the center speaker distance 1–2
meters (3–6 feet) closer than the actual speaker
position will create a fairly realistic sensation of being
“inside” the screen. If you cannot obtain a satisfactory
surround effect because the surround speakers are too
close, setting the surround speaker distance closer
(shorter) than the actual distance will create a larger
sound stage.
x CTR DIST. X.X m (XX ft.)
(Center speaker distance)
Initial setting: 3.0 m (10 ft.)
Lets you set the distance from your listening position
to the center speaker. Center speaker distance should
be set from a distance equal to the front speaker
distance (A on page 19) to a distance 1.5 meters (5
feet) closer to your listening position (B on page 19).
Adjusting these parameter while listening to the sound
often results in much better surround sound. Give it a
x SURR DIST. X.X m (XX ft.)
(Surround speaker distance)
Initial setting: 3.0 m (10 ft.)
x PL. XXXX/XXXX
Lets you set the distance from your listening position
to the surround speakers. Surround speaker distance
should be set from a distance equal to the front speaker
distance (A on page 19) to a distance 4.5 meters (15
feet) closer to your listening position (C on page 19).
If both surround speakers are not placed an equal
distance from your listening position, set the distance
to the closest speaker.
(Surround speaker position)*
Lets you specify the location of your surround speakers
for proper implementation of the surround effects in
the Cinema Studio EX modes (page 30).
x SB DIST. X.X m (XX ft.)
120˚
100˚
Lets you set the distance from your listening position
to the surround back speaker. Surround back speaker
distance should be set from a distance equal to the front
speaker distance (A on page 19) to a distance 4.5
meters (15 feet) closer to your listening position (D on
page 19).
A
A
B
B
If you connect two surround back speakers and both
surround back speakers are not placed an equal
distance from your listening position, set the distance
to the closest speaker.
D
D
C
Tip
60
C
The receiver lets you to input the speaker position in
terms of distance. However, it is not possible to set the
center speaker further than the front speakers. Also, the
center speaker cannot be set more than 1.5 meters (5
feet) closer than the front speakers.
30
• SIDE/LOW
Likewise, the surround speakers and the surround back
speakers cannot be set further away from the listening
position than the front speakers. And they can be no
more than 4.5 meters (15 feet) closer.
Select if the location of your surround speakers
corresponds to section A and C.
• SIDE/HIGH
Select if the location of your surround speakers
corresponds to section A and D.
• BEHD/LOW
This is because incorrect speaker placement is not
conducive to the enjoyment of surround sound.
Please note that, setting the speaker distance closer than
the actual location of the speakers will cause a delay in
the output of the sound from that speaker. In other
words, the speaker will sound like it is further away.
Select if the location of your surround speakers
corresponds to section B and C.
• BEHD/HIGH
Select if the location of your surround speakers
corresponds to section B and D.
* This setup item is not available when the surround
speakers size parameter is set to “NO”.
20GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
Surround speaker position is designed specifically for
implementation of the Cinema Studio EX modes.
For other sound fields, speaker position is not so
critical. Those sound fields were designed under the
premise that the surround speakers would be located
behind the listening position, but presentation remains
fairly consistent even with the surround speakers
positioned at a rather wide angle. However, if the
speakers are pointing toward the listener from the
immediate left and right of the listening position, the
surround effects becomes unclear unless set to
“SIDE/LOW” or “SIDE/HIGH”.
6: Adjusting the speaker
levels and balance
— TEST TONE
Adjust the speaker levels and balance while
listening to the test tone from your listening
position. Use the remote for the operation.
Tip
The receiver employs a test tone with a frequency
centered at 800 Hz.
Nevertheless, each listening environment has many
variables, such as wall reflections, and you may obtain
better results using “BEHD/HIGH” if your speakers
are located high above the listening position, even if
they are to the immediate left and right.
1
2
Press ?/1 to turn on the receiver.
Press TEST TONE.
“TEST TONE [XXX]” appears in the
display and the test tone is output from each
speaker in sequence.
Therefore, although it may result in a setting contrary
to the above explanation, we recommend that you
playback multi channel surround encoded software and
select the setting that provides a good sense of
spaciousness and that best succeeds in forming a
cohesive space between the surround sound from the
surround speakers and the sound of the front speakers.
If you are not sure which sounds best, select
“BEHD/LOW” or “BEHD/HIGH” and then use the
speaker distance parameter and speaker level
adjustments to obtain proper balance.
Front (left) t Center t Front (right) t
Surround (right) t Surround back (right)*
t Surround back (left)* t Surround
(left) t Sub woofer
* You will only hear the test tone from the
– surround back left and right speakers when
surround back speaker selection is set to
“DUAL”.
– surround back left speaker when surround
back speaker selection is set to “SINGLE”.
3
4
using the LEVEL menu so that the level
of the test tone sounds the same from
each speaker.
For details on the LEVEL menu settings,
see page 35.
Tips
• To adjust the level of all speakers at the same
time, press MASTER VOL +/– on the remote or
turn MASTER VOLUME –/+ on the receiver.
• The adjusted value are shown in the display
during adjustment.
Press TEST TONE again after
adjustment.
The test tone turns off.
Notes
• The test tone cannot be used when MULTI CH IN
1/2 or ANALOG DIRECT function is used.
• Although these adjustments can also be made via the
front panel using the LEVEL menu (when the test
tone is output, the receiver switches to the LEVEL
menu automatically), we recommend you follow the
procedure described above and adjust the speaker
levels from your listening position using the remote.
21GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the headphones
Connect the headphones to the PHONES jack.
output is automatically canceled and “SP.A”
and “SP.B” do not light up in the display.
• When the headphones are connected, you can
select only the following sound fields
(page 31).
Amplifier Operation
Selecting the component
1
Turn INPUT SELECTOR to select the
input.
To select the
Display/light up
– HP 2CH (HEADPHONE 2CH)
VCR
VIDEO 1 or
VIDEO 2
– HP DIRECT (HEADPHONE DIRECT)
– HP MULTI 1 (HEADPHONE MULTI 1)
– HP MULTI 2 (HEADPHONE MULTI 2)
Camcorder or video game VIDEO 3
DVD player
DVD
Satellite tuner
MD or tape deck
TV/SAT
MD/TAPE
SA-CD/CD
– HP THEATER (HEADPHONE
THEATER)
Super Audio CD or CD
player
Built-in tuner (FM/AM)
Turntable
TUNER FM/AM
PHONO
2
3
Turn on the component and start
playback.
Note
If you select the VCR or DVD player, set the
TV’s video input to match the component you
selected.
Turn MASTER VOLUME –/+ to adjust
the volume.
Note
To avoid damaging your speakers, make sure that
you turn down the volume before you turn off the
receiver.
To mute the sound
Press MUTING on the remote.
The muting function will be canceled when you
do the following.
• Press MUTING on the remote again.
• Turn the power off.
• Increase the volume.
22GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to multi channel
sound
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and AM
antennas to the receiver (see page 14).
— MULTI CH IN
You can select the audio directly from the
components connected to the MULTI CH IN 1
or 2 jacks. This enables you to enjoy high quality
analog inputs like DVD or Super Audio CD.
When MULTI CH IN function is selected, the
equalizer and sound field cannot be used.
Tip
The tuning scale differs depending on the area code as
shown in the following table. For details on area codes,
see page 3.
Area code
U, CA
E2/E3
AR
FM
AM
Press MULTI CH IN/DIRECT repeatedly to
select “MULTI 1 DIRECT” or “MULTI 2
DIRECT”.
100 kHz
50 kHz
50 kHz
10 kHz*
9 kHz*
10 kHz
To cancel the MULTI CH IN function, press
MULTI CH IN/DIRECT repeatedly until
“MULTI CH IN 1”, “MULTI CH IN 2” and
“A.DIRECT” indication turns off.
* The AM tuning scale can be changed (see page 59).
Automatic tuning
If you do not know the frequency of the station
you want, you can let the receiver scan all
available stations in your area.
When MULTI CHANNEL
DECODING indicator lights up
The MULTI CHANNEL DECODING indicator
lights up when the receiver is decoding multi
channel sources.
However, this indicator does not light up if you
select 2CH STEREO mode.
1
Turn INPUT SELECTOR to select the
FM or AM band.
The last received station is tuned in.
2
Press TUNING + or TUNING –.
Press TUNING + to scan from low to high;
press TUNING – to scan from high to low.
The receiver stops scanning whenever a
station is received.
Tip
If “STEREO” flashes in the display and the FM stereo
reception is poor, press FM MODE to change to
monaural (MONO). You will not be able to enjoy the
stereo effect, but the sound will be less distorted. To
return to stereo mode, press FM MODE again.
continued
23GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct tuning
Presetting radio stations
You can enter the frequency of the station you
want directly. Use the remote for the operation.
You can preset up to 30 FM or AM stations.
Then you can easily tune in the stations you
often listen to.
1
Press TUNER repeatedly to select the
FM or AM band.
The last received station is tuned in.
Presetting radio stations
Tip
You can also use INPUT SELECTOR on the
receiver.
1
FM or AM band.
The last received station is tuned in.
2
3
Press D.TUNING.
2
3
Tune in the station that you want to
preset using Automatic Tuning
(page 23) or Direct Tuning (page 24).
Press the numeric buttons to enter the
frequency.
Example 1: FM 102.50 MHz
Press 1 b 0 b 2 b 5 b 0
Example 2: AM 1,350 kHz
(You do not have to enter the last “0” when
the tuning scale is set to 10 kHz.)
Press 1 b 3 b 5 b 0
If you have tuned in an AM station, adjust
the direction of the AM loop antenna for
optimum reception.
Press MEMORY.
“MEMORY” appears in the display for a
few seconds. Do steps 4 to 5 before the
display goes out.
4
Press PRESET TUNING + or PRESET
TUNING – repeatedly to select a preset
station number.
Each time you press the button, you can
select the preset station number as follows:
If you cannot tune in a station
and the entered numbers flash
Make sure you have entered the right frequency.
If not, repeat steps 2 and 3. If the entered
numbers still flash, the frequency is not used in
your area.
tC0y...yC2yC1T
If “MEMORY” goes out before you select
the preset station number, start again from
step 3.
Tip
You can also use the remote to select a preset
station number. Press SHIFT repeatedly to select
a memory page (A, B or C) and then press the
numeric button to select a preset number.
5
Press MEMORY again.
The station is stored to the selected preset
number.
If “MEMORY” goes out before you press
MEMORY, start again from step 3.
6
Repeat steps 2 to 5 to preset another
station.
24GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning to preset stations
Changing the display
1
Turn INPUT SELECTOR to select the
FM or AM band.
Changing the information in
the display
The last received station is tuned in.
2
Press PRESET TUNING + or PRESET
TUNING – repeatedly to select the
preset station you want.
You can check the sound field etc. by changing
the information in the display.
Each time you press the button, you can
select the preset station as follows:
Press DISPLAY repeatedly.
Each time you press DISPLAY, the display will
change cyclically as follows.
tA1yA2y...yA0yB1yB2y...yB0T
*
Index name of the input t Selected input t
Sound field currently applied
tC0y...yC2yC1T
When the tuner is selected
*
Using the remote
Preset station name t Frequency t Sound
field currently applied
1 Press TUNER repeatedly to select the FM or
* Index name appears only when you have assigned
one to the input or preset station (page 39). Index
name does not appear when only blank spaces have
been entered, or it is the same as the input name.
AM band.
2 Press PRESET/CH/D.SKIP +/– repeatedly
to select the preset station you want.
To select the preset station
directly
Adjusting the brightness of
the display
Press the numeric buttons on the remote.
The preset station of the selected number in the
current memory page is tuned in. Press SHIFT
repeatedly on the remote to change the memory
page.
Press DIMMER repeatedly.
The brightness of the display will change in 3
steps.
25GB
Download from Www.Somanuals.com. All Manuals Search And Download.
About the indications in the display
1 2
3
4
5
6
7
8
9
q;
qa
MULTI CH IN 1 2 EQ D.RANGE
A.DIRECT
;
;
DIGITAL EX
PRO LOGIC II 96/24 NEO:6
DTS-ES
SP.A SP.B
SLEEP
OPT COAX MONO
D.ASSIGN STEREO
MEMORY
SW LFE
L
C
S
R
SL
SR
qh
qg
qf
qd
qs
SBL SB SBR
qj
A SW: Lights up when sub woofer selection is
set to “YES” (page 18) and the audio signal is
output from the SUB WOOFER jacks.
I OPT: Lights up when the source signal is a
digital signal being input through the
OPTICAL terminal or when INPUT MODE is
set to “OPT FIXED” (page 35).
B LFE: Lights up when the disc being played
back contains the LFE (Low Frequency
Effect) channel and the LFE channel signal is
actually being reproduced.
J COAX: Lights up when the source signal is a
digital signal being input through the
COAXIAL terminal or when INPUT MODE
is set to “COAX FIXED” (page 35).
C SP.A/SP.B: Lights up in accordance with the
speaker system being used (A or B). Turns off
when speaker output is turned off or when
headphones are connected.
K Tuner indicators: Lights up when using the
receiver to tune in radio stations, etc. See
pages 23–25 for tuner operations.
“MULTI 1 DIRECT” or “MULTI 2 DIRECT”
is selected.
L D.ASSIGN: Lights up when the digital assign
function is used for the selected input.
M NEO:6: Lights up when DTS Neo:6 Cinema/
Music mode decoding is activated. However,
this indicator does not light up if both the
E EQ: Lights up when the equalizer functions.
F D.RANGE: Lights up when dynamic range
center and surround speakers are set to “NO”.
compression is activated (page 36).
N ; PRO LOGIC II: “; PRO LOGIC” lights
up when the receiver applies Pro Logic
processing to 2 channel signals in order to
output the center and surround channel
signals. “; PRO LOGIC II” lights up when
the Pro Logic II Movie/Music decoder is
activated. However, both indicators do not
light up if both the center and surround
speakers are set to “NO” and “A.F.D. AUTO”,
“PRO LOGIC”, “PLII MOVIE” or
G ; DIGITAL EX: “; DIGITAL” lights up
when the receiver is decoding signals recorded
in the Dolby Digital format.
“; DIGITAL EX” lights up when the
receiver is decoding signals recorded in the
Dolby Digital EX format.
H DTS-ES 96/24: “DTS” lights up when DTS
signals are input. “DTS-ES” lights up when
DTS-ES signals are input. “DTS 96/24” lights
up when the receiver is decoding DTS 96 kHz/
“PLII MUSIC” is selected.
Note
Note
Dolby Pro Logic and Dolby Pro Logic II
decoding do not function for DTS format signals.
When playing a DTS format disc, be sure that you
have made digital connections and that INPUT
MODE is not set to “ANALOG FIXED”
(page 35).
O A.DIRECT: Lights up when you select
ANALOG DIRECT.
26GB
Download from Www.Somanuals.com. All Manuals Search And Download.
P SLEEP: Lights up when sleep timer is
activated.
Q Playback channel indicators: The letters
(L, C, R, etc.) indicate the channels being
played back. The boxes around the letters vary
to show how the receiver downmixes the
source sound (based on the speakers settings).
L (Front Left), R (Front Right), C (Center
(monaural)), SL (Surround Left), SR
(Surround Right), S (Surround (monaural or
the surround components obtained by Pro
Logic processing)), SB (Surround Back (the
surround back components obtained by 6.1
channel decoding)), SBL (Surround Back
Left), SBR (Surround Back Right)
Example:
Recording format (Front /Surround): 3/2
Output channel: Surround speakers absent
Sound Field: A.F.D. AUTO
L
C
R
SL
SR
27GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to analog audio
(ANALOG DIRECT)
Enjoying Surround Sound
You can switch the audio of the selected input to
the two channel analog input. This function
enables you to enjoy high quality analog
sources.
Using only the front
speakers
When using this function, only the volume and
front speaker balance can be adjusted.
In this mode, the receiver outputs the sound
from the front left/right speakers only. There is
no sound from the sub woofer.
1
Turn INPUT SELECTOR to select the
input you want to listen to in analog
audio.
Listening to 2 channel stereo
sources (2CH STEREO)
2
Press MULTI CH IN/DIRECT repeatedly
to select “ANALOG DIRECT”.
Standard 2 channel stereo sources completely
bypass the sound field processing and multi
channel surround formats are downmixed to 2
channel.
“ANALOG DIRECT” appears in the display
and the analog audio is output.
To cancel the ANALOG DIRECT function,
press MULTI CH IN/DIRECT repeatedly until
“MULTI CH IN 1”, “MULTI CH IN 2” and
“A.DIRECT” indication turns off.
Press 2CH.
“2CH STEREO” appears in the display and the
receiver switches to the 2CH STEREO mode.
Note
When the ANALOG DIRECT function is selected, the
equalizer and sound field cannot be used.
Note
No sound is output from the sub woofer in the 2CH
STEREO mode. To listen to the 2 channel stereo
sources using the front left/right speakers and a sub
woofer, set to the A.F.D. mode.
28GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying stereo sound in multi
channel (2 channel decoding
mode)
Enjoying higher fidelity
sound
— AUTO FORMAT DIRECT
This mode lets you specify the type of decoding
for 2 channel audio sources. This receiver can
reproduce 2 channel sound in 5 channels
through Dolby Pro Logic II; 6 channels through
DTS Neo:6 or 4 channels through Dolby Pro
Logic. However, DTS 2CH sources are not
decoded by DTS Neo:6; they are output in 2
channels.
The Auto Format Direct (A.F.D.) mode allows
you to select the decoding mode you want for
your audio sound.
A.F.D. mode
(Display)
Decoding mode
A.F.D. AUTO
As encoded
(A.F.D. AUTO)
Press A.F.D. repeatedly to select the 2
channel decoding mode.
PRO LOGIC
Dolby Pro Logic
(PRO LOGIC)
The selected type of decoding appears in the
display.
PRO LOGIC II MOVIE Dolby Pro Logic II
(PLII MOVIE)
x PRO LOGIC (PRO LOGIC)
PRO LOGIC II MUSIC
(PLII MUSIC)
Performs Dolby Pro Logic decoding. The source
recorded in 2 channel is decoded into 4.1 channels.
Neo:6 Cinema
DTS Neo:6
x PLII MOVIE (PRO LOGIC II MOVIE)
(NEO6 CINEMA)
Performs Dolby Pro Logic II Movie mode decoding.
This setting is ideal for movies encoded in Dolby
Surround. In addition, this mode can reproduce sound
in 5.1 channel when watching videos of overdubbed or
old movies.
Neo:6 Music
(NEO6 MUSIC)
Decoding the input audio
signal automatically
x PLII MUSIC (PRO LOGIC II MUSIC)
Performs Dolby Pro Logic II Music mode decoding.
This setting is ideal for normal stereo sources such as
CDs.
In this mode, the receiver automatically detects
the type of audio signal being input (Dolby
Digital, DTS, standard 2 channel stereo, etc.)
and performs the proper decoding if necessary.
This mode presents the sound as it was recorded/
encoded, without adding any surround effects.
However, if there are no low frequency signals
(Dolby Digital LFE, etc.) it will generate a low
frequency signal for output to the sub woofer.
Note
Dolby Pro Logic and Dolby Pro Logic II decoding do
not function for DTS format signals.
x NEO6 CINEMA
Performs DTS Neo:6 Cinema mode decoding.
x NEO6 MUSIC
Press A.F.D. repeatedly to select “A.F.D.
AUTO”.
Performs DTS Neo:6 Music mode decoding. This
setting is ideal for normal stereo sources such as CDs.
The receiver automatically detects the type of
audio signal being input and performs the proper
decoding if necessary.
If you connect a sub woofer
When the audio signal is 2 channel stereo or if
the source signal does not include a LFE signal,
the receiver generates a low frequency signal for
output to the sub woofer. However the low
frequency signal is not generated when “Neo:6
Cinema” or “Neo:6 Music” is selected.
29GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x CINEMA ST. EX B
(CINEMA STUDIO EX B) DCS
Selecting a sound field
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Kim Novak Theater” cinema
production studio. This mode is ideal for watching
science-fiction or action movies with lots of sound
effects.
You can take advantage of surround sound
simply by selecting one of the receiver’s pre-
programmed sound fields. They bring the
exciting and powerful sound of movie theaters
and concert halls into your home.
x CINEMA ST. EX C
(CINEMA STUDIO EX C) DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment scoring stage. This mode is
ideal for watching musicals or films where orchestra
music is featured in the soundtrack.
Selecting a sound field for
movies
Press MOVIE repeatedly to select the
sound field you want.
About CINEMA STUDIO EX modes
The selected sound field appears in the display.
CINEMA STUDIO EX modes are suitable for
watching motion picture DVDs (etc.), with
multi channel surround effects. You can
reproduce the sound characteristics of Sony
Pictures Entertainment’s dubbing studio in your
home.
The CINEMA STUDIO EX modes consist of
the following three elements.
• Virtual Multi Dimension
Sound field
Display
CINEMA STUDIO EX A
CINEMA ST. EX A
DCS
CINEMA STUDIO EX B
DCS
CINEMA ST. EX B
CINEMA ST. EX C
CINEMA STUDIO EX C
DCS
Creates 5 sets of virtual speakers from a single
pair of actual surround speakers.
• Screen Depth Matching
Creates the sensation that the sound is coming
from inside the screen like in theaters.
• Cinema Studio Reverberation
Reproduces the type of reverberation found in
theaters.
About DCS (Digital Cinema
Sound)
Sound fields with DCS marks use DCS
technology.
DCS is the concept name of the surround
technology for home theater developed by Sony.
DCS uses the DSP (Digital Signal Processor)
technology to reproduce the sound
characteristics of an actual cinema cutting studio
in Hollywood.
The CINEMA STUDIO EX modes integrate
these three elements simultaneously.
When played at home, DCS will create a
powerful theater effect that mimics the artistic
combination of sound and action as envisioned
by the movie director.
Notes
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
x CINEMA ST. EX A
(CINEMA STUDIO EX A) DCS
Reproduces the sound characteristics of the Sony
Pictures Entertainment “Cary Grant Theater” cinema
production studio. This is a standard mode, great for
watching most any type of movies.
30GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn off the surround effect
Selecting a sound field for
music
Press 2CH to select “2CH STEREO” or press
A.F.D. repeatedly to select “A.F.D. AUTO”.
Press MUSIC repeatedly to select the
sound field you want.
Tips
• The receiver lets you apply the last selected sound
field to an input whenever it is selected (Sound Field
Link). For example, if you select HALL for the
SA-CD/CD input, then change to a different input
and then return to SA-CD/CD, HALL will
automatically be applied again.
The selected sound field appears in the display.
Sound field
HALL
Display
HALL
JAZZ CLUB
LIVE CONCERT
JAZZ CLUB
LIVE CONCERT
• You can identify the encoding format of DVD
software, etc. by looking at the logo on the package.
–
–
: Dolby Digital discs
: Dolby Surround encoded
xHALL
Reproduces the acoustics of a classical concert hall.
programs
: DTS Digital Surround encoded programs
xJAZZ CLUB
–
Reproduces the acoustics of a jazz club.
Notes
xLIVE CONCERT
• Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
• When one of the following sound fields are selected,
no sound is output from the sub woofer if all the
speakers are set to “LARGE” in the SET UP menu.
However, the sound will be output from the sub
woofer if the digital input signal contains LFE (Low
Frequency Effect) signals, or if the front, center, or
surround speakers are set to “SMALL”.
– HALL
Reproduces the acoustics of a 300-seat live house.
When the headphones are
connected
You can select only from the following sound
fields.
xHP 2CH (HEADPHONE 2CH)
Outputs the sound in 2 channel (stereo). Standard 2
channel stereo sources completely bypass the sound
field processing and multi channel surround formats
are downmixed to 2 channels.
– JAZZ CLUB
– LIVE CONCERT
xHP DIRECT (HEADPHONE DIRECT)
Outputs the analog signals without processing by the
equalizer, sound field, etc.
xHP MULTI 1/2
(HEADPHONE MULTI 1 or 2)
Outputs the front analog signals from MULTI CH IN 1
or 2 jacks.
xHP THEATER
(HEADPHONE THEATER) DCS
Allows you to experience a theater-like environment
while listening through a pair of headphones.
Note
If you connect a pair of headphones while a sound field
is operating, the system will automatically switch to
“HP 2CH” if using a sound field selected with the 2CH
or A.F.D. button, or to “HP THEATER” if using a
sound field selected with the MOVIE or MUSIC
button.
31GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the surround
back decoding mode
— SURR BACK DECODING
This function lets you select the decoding mode
for the surround back signals of the multi
channel input stream.
By decoding the surround back signal of DVD
software (etc.) recorded in Dolby Digital EX,
DTS-ES Matrix, DTS-ES Discrete 6.1, etc.
format, you can enjoy the surround sound
intended by the filmmakers.
to select the surround back decoding
mode.
“SB DEC XXXXXX” appears in the display.
decoding mode” on page 33.
Tip
“SB DEC XXXXXX” in the CUSTOMIZE menu
(page 38).
Note
You can select the surround back decoding mode only
when A.F.D. mode is selected (page 29).
32GB
Download from Www.Somanuals.com. All Manuals Search And Download.
How to select the surround back decoding mode
You can select the surround back mode you want according to the input stream.
When you select “AUTO”
a)
When the input stream contains the 6.1 channel decode flag , the appropriate decoder is applied to
decode the surround back signal.
Input stream
Dolby Digital 5.1
Dolby Digital EX
DTS 5.1
Output channel
Applied surround back decoder
e)
5.1
—
b)
e)
6.1
Matrix decoder conforms to Dolby Digital EX
e)
5.1
—
c)
e)
DTS-ES Matrix 6.1
6.1
DTS Matrix decoder
DTS Discrete decoder
d)
e)
DTS-ES Discrete 6.1
6.1
When you select “MATRIX”
Dolby Digital EX is applied to decode the surround back signal regardless of the 6.1 channel decode
a)
flag in the input stream. This decoder conforms to Dolby Digital EX and functions the same as the
f)
decoders used in movie theaters.
Input stream
Dolby Digital 5.1
Dolby Digital EX
DTS 5.1
Output channel
Applied surround back decoder
e)
6.1
Matrix decoder conforms to Dolby Digital EX
Matrix decoder conforms to Dolby Digital EX
Matrix decoder conforms to Dolby Digital EX
Matrix decoder conforms to Dolby Digital EX
Matrix decoder conforms to Dolby Digital EX
b)
e)
6.1
e)
6.1
c)
e)
DTS-ES Matrix 6.1
6.1
d)
e)
DTS-ES Discrete 6.1
6.1
When you select “OFF”
Surround back decoding is not performed.
a)
6.1 channel decode flag is the information recorded in software like DVDs.
b)
Dolby Digital DVD that includes a Surround EX flag. The Dolby Corporation web page can help you distinguish
Surround EX films.
c)
d)
Software encoded with a flag to denote it has both Surround EX and 5.1 channel signals.
Software encoded with both 5.1 channel signals and an extension stream designed for returning those signals to
6.1 discrete channels. Discrete 6.1 channel signals are DVD specific signals not used in movie theaters.
When two surround back speakers are connected, the output channel will be 7.1 channels.
This decoder can be used for all 6.1 formats (Dolby Digital EX, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1).
e)
f)
Note
There may be no sound from the surround back speaker in Dolby Digital EX mode. Some discs have no Dolby Digital
EX flag even though the packages have Dolby Digital EX logos. In this case, select “MATRIX”.
33GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Selectable audio inputs for each
input
Advanced Adjustments and Settings
VIDEO 3 OPT
VIDEO 3, VIDEO 1, VIDEO 2
DVD COAX
Assigning the audio input
— DIGITAL ASSIGN
DVD, VIDEO 1, VIDEO 2
TV/SAT OPT
You can assign a digital audio input for another
input. This function is convenient in the
following example.
TV/SAT, VIDEO 1, VIDEO 2
SA-CD/CD COAX, SA-CD/CD OPT
SA-CD/CD, VIDEO 1, VIDEO 2
MD/TAPE OPT
When you have two DVD players and no
digital audio input jack is available for the
second DVD player.
MD/TAPE, VIDEO 1, VIDEO 2
Connect the first DVD player to the DVD
COAXIAL IN jack on the receiver. You can
connect the second DVD player to the TV/SAT
OPTICAL IN jack and its analog audio/video
output jacks to the VIDEO 2 AUDIO IN and
VIDEO IN jacks on the receiver.
Then, assign the DVD COAXIAL’s digital
audio input to DVD (DVD–DVD) and the
TV/SAT OPTICAL’s digital audio input to
VIDEO 2 (TV/SAT–VIDEO 2).
Notes
• You cannot assign several audio inputs to the same
input.
• You cannot use the audio input for the original input
when it is assigned to another input.
• When you assign the audio input, the INPUT MODE
setting may change automatically (page 35).
• You cannot assign for TUNER and PHONO.
1
2
Press MAIN MENU repeatedly to select
CUSTOMIZE ”.
“
Press or repeatedly to select
“DIGITAL ASSIGN”.
3
4
Press ENTER.
Press
or
repeatedly to select the
digital audio input you want to assign.
5
assign the digital audio input jack
selected in step 4.
The input you can assign varies for each
audio input. For details, see “Selectable
audio inputs for each input”.
Tip
When you assign the SA-CD/CD digital audio input,
only “SA-CD” appears in the display.
34GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching the audio input
mode for digital
components
Customizing sound fields
By adjusting the LEVEL menu, you can
customize the sound fields to suit your particular
listening situation.
— INPUT MODE
Note on the displayed items
The setup items you can adjust in each menu vary
depending on the sound field. Certain setup parameters
may be dimmed in the display. This means that the
selected parameter is either unavailable or fixed and
unchangeable.
You can switch the audio input mode for
components which have digital audio input
jacks.
1
2
Turn INPUT SELECTOR to select the
input.
Adjusting the LEVEL menu
Press INPUT MODE repeatedly to
select the audio input mode.
You can adjust the balance and level of each
speaker. These settings are applied to all sound
fields except for effect level parameter. The
effect level parameter settings are stored
individually for each sound field.
The selected audio input mode appears in
the display.
Audio input modes
• AUTO 2CH
1
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
Gives priority to digital signals when there are
both digital and analog connections. If there
are no digital signals, analog is selected.
• COAX FIXED
Specifies the digital audio signals input to the
DIGITAL COAXIAL input jack.
• OPT FIXED
2
3
Press MAIN MENU repeatedly to select
“
LEVEL ”.
Press or
repeatedly to select the
parameter you want to adjust.
Specifies the digital audio signals input to the
DIGITAL OPTICAL input jacks.
• ANALOG FIXED
Specifies the analog audio signals input to the
AUDIO IN (L/R) jacks.
For details, see “LEVEL menu parameters”
below.
4
5
While monitoring the sound, turn –/+ to
select the setting you want.
The setting is entered automatically.
Notes
Repeat steps 3 and 4 to adjust the other
parameters.
• When signals with a sampling frequency of more
than 48 kHz is input, the equalizer and sound field
cannot be used.
LEVEL menu parameters
• You cannot select the digital audio input which is
assigned to another function by DIGITAL ASSIGN
function (page 34).
The initial setting is underlined.
L
R
x
BALANCE L/R XX
(Front speaker balance)1)
Initial setting: BALANCE (0)
Lets you adjust the balance between front left and right
speakers. You can adjust in the range of BALANCE L
(+1 to +8), BALANCE (0), BALANCE R (+1 to +8) in
17 steps.
continued
35GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x CENTER XXX.X dB
x EFFECT XXX (Effect level)
(Center speaker level)1)
Initial setting: STD
Lets you adjust the “presence” of the surround effect.
x SURR L XXX.X dB
(Surround speaker (Left) level)1)
Resetting sound fields to the
initial settings
x SURR R XXX.X dB
(Surround speaker (Right) level)1)
x SB XXX.X dB
Use the buttons on the receiver for the operation.
(Surround back speaker level)1)2)
1
2
Press ?/1 to turn off the power.
x SB LEFT XXX.X dB
(Surround back (Left) level)1)3)
While holding down 2CH, press
?/1.
x SB RIGHT XXX.X dB
“SF. INITIALIZE” appears in the display
and all sound fields are reset to the initial
setting.
(Surround back (Right) level)1)3)
x SW XXX.X dB
(Sub woofer level)1)
Initial setting: 0 dB
You can adjust from –10 dB to +10 dB in 0.5 dB steps.
1)
The parameters can be adjusted seperately for
MULTI CH IN 1 and 2.
2)
Only when the surround back speaker is set to
“SINGLE” in the SET UP menu (page 19).
3)
Only when the surround back speaker is set to
“DUAL” in the SET UP menu (page 19).
D.RANGE
x
COMP. XXX
(Dynamic range compressor)
Lets you compress the dynamic range of the sound
track. This may be useful when you want to watch
movies at low volumes late at night.
• OFF
The dynamic range is not compressed.
• STD
The dynamic range is compressed as intended by the
recording engineer.
• MAX
The dynamic range is compressed dramatically.
Tip
Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the dynamic
range information included in the Dolby Digital signal.
We recommend using the “MAX” setting. This greatly
compresses the dynamic range and lets you view
movies late at night at low volumes. Unlike analog
limiters, the levels are predetermined and provide a
very natural compression.
Note
Dynamic range compression is possible with Dolby
Digital sources only.
36GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the equalizer
Advanced settings
You can adjust the tonal quality (bass, treble
level) of the front speakers using the
EQUALIZER menu.
Using the CUSTOMIZE menu
to adjust the receiver
1
Start playing a source encoded with
multi channel surround effects (DVD,
etc.).
You can adjust various receiver settings using
the CUSTOMIZE menu.
2
CUSTOMIZE ”.
2
3
Press MAIN MENU repeatedly to select
“
“
EQUALIZER ”.
Press or repeatedly to select the
parameter you want to adjust.
Press or repeatedly to select the
parameter you want to adjust.
For details, see “CUSTOMIZE menu
parameters” below.
For details, see “EQUALIZER menu
parameters” below.
3
4
Turn –/+ to select the setting you want.
4
5
While monitoring the sound, turn –/+ to
select the setting you want.
The setting is entered automatically.
Repeat steps 2 and 3 to adjust the other
items.
The setting is entered automatically.
Repeat steps 3 and 4 to adjust the other
items.
CUSTOMIZE menu parameters
The initial settings are underlined.
DTS 96/24
Note
You cannot adjust the equalizer when the receiver is
decoding signals with a sampling frequency of more
than 48 kHz, or when DTS 96/24, DTS-ES Matrix or
DTS Neo:6 decoding is applied.
x
96/24 DEC XXXX
(DTS 96/24 decoding mode)
• AUTO
When a DTS 96/24 signal is input, it is played back
at 96 kHz sampling frequencies.
• OFF
EQUALIZER menu parameters
xBASS XXX.X dB
Even when a DTS 96/24 signal is input, it is played
back at 48 kHz sampling frequencies.
(Front speaker bass level)
xTREBLE XXX.X dB
Notes
(Front speaker treble level)
• This parameter is valid only in the A.F.D. mode
(page 29). In other sound fields, this parameter is
always set to “96/24 DEC OFF”.
Initial setting: 0 dB
You can adjust from –10 dB to +10 dB in 0.5 dB steps.
• DTS 96/24 decoding is only valid in the A.F.D. mode
(page 29). When the system is set to other sound
fields, standard 48 kHz decoding is used.
• Even when a DTS 96/24 signal is input, standard
48 kHz decoding is used if any speakers are set to
“SMALL” or if the sub woofer is set to “NO”.
xEQUALIZER XXX
Initial setting: OFF
Select “ON” to activate the equalizer.
Note
The EQ indicator in the display lights up when the
equalizer is turned on. When you adjust the equalizer
using the EQUALIZER parameters, the settings are
applied to all sound fields and can be reproduced
whenever you turn on the equalizer.
continued
37GB
Download from Www.Somanuals.com. All Manuals Search And Download.
x SB DEC XXXXXX
x DUAL MONO XXXX
(Surround back decoding mode)
(Digital broadcast language selection)
You can also use the SURR BACK DECODING to set
the surround back decoding mode (page 32).
Lets you select the language you want to listen to
during digital broadcast. This feature only functions
for Dolby Digital sources.
For details on each decoding mode, see page 33.
• M/S (Main/Sub)
• OFF
Sound of the main language will be output through
the front left speaker and sound of the sub language
will be output through the front right speaker
simultaneously.
• AUTO
• MATRIX
Note
This parameter is valid only in the A.F.D. mode
(page 29).
• MAIN
Sound of the main language will be output.
• SUB
x DEC. PRI. XXXX
Sound of the sub language will be output.
• M+S (Main + Sub)
(Digital audio input decoding priority)
Lets you specify the input mode for the digital signal
input to the DIGITAL IN jacks.
Mixed sound of both the main and sub languages will
be output.
The initial setting is “DEC. PRI. AUTO” for VIDEO 1,
2, 3 and TV/SAT, and “DEC. PRI. PCM” for DVD,
MD/TAPE and SA-CD/CD.
x DIGITAL ASSIGN
(Digital audio input assignment)
• AUTO
Lets you assign the digital audio input to other input.
For details, see “Assigning the audio input” on
page 34.
Automatically switches the input mode between
DTS, Dolby Digital, or PCM.
• PCM
x NAME IN
(Naming preset stations and inputs)
PCM signals are given priority (to prevent the
interruption when playback starts). Even when other
signals are input, the sound is output. However, this
receiver cannot decode DTS-CD when set to “DEC.
PRI. PCM”.
Lets you set the name of preset stations and inputs
selected with INPUT SELECTOR. For details, see
“Naming preset stations and inputs” on page 39.
Note
When set to “DEC. PRI. AUTO” and the sound from
the digital audio jacks (for SA-CD/CD, etc.) is
interrupted when playback starts, set to “DEC. PRI.
PCM”.
x POWER SAVE XXX (CONTROL A1II
power save function)
• ON
during standby mode when the power save function
is activated.
• OFF
Lets you turn on the system automatically when the
component connected via monaural mini-plug cords
(page 42) is turned on.
38GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Sleep Timer
Other Operations
You can set the receiver to turn off automatically
at a specified time. Use the remote for the
operation.
Naming preset stations
and inputs
1
2
Press ALT to light up the button.
Press SLEEP while the power is on.
You can enter a name of up to 8 characters for
preset stations and inputs selected with INPUT
SELECTOR, and display it in the receiver’s
display.
Each time you press SLEEP, the display
changes cyclically as follows:
2-00-00 t 1-30-00 t 1-00-00 t
0-30-00 t OFF
1 To index a preset station
While using Sleep Timer, “SLEEP” lights up in
the display.
Turn INPUT SELECTOR to select the
FM or AM band, then tune in the preset
station you want to create an index
name for (page 25).
Tip
To check the remaining time before the receiver turns
off, press ALT to light up the button (page 45), then
press SLEEP. The remaining time appears in the
display. If you press SLEEP again, the sleep timer will
be canceled.
To index an input
Turn INPUT SELECTOR to select the
input you want to create an index name
for.
2
3
4
Press MAIN MENU repeatedly to select
CUSTOMIZE ”.
“
Press or repeatedly to select
“NAME IN”.
Press ENTER.
The cursor flashes and you can select a
character.
5
Use
name.
or
and –/+ to create an index
Turn –/+ to select a character, then press >
to move the cursor to the next position.
Tips
• You can select the character type as follows by
turning –/+.
Alphabet (upper case) t Numbers t Symbols
• To enter a blank space, turn –/+ until a blank
space appears in the display.
• If you made a mistake, press < or > repeatedly
until the character you want to change flashes,
then turn –/+ to select the correct character.
6
Press ENTER to store the index name.
39GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the speaker
system
Recording
Before you begin, make sure you have
connected all components properly.
You can select the front speaker system you
want to use.
Recording on an audio tape or
MiniDisc
Press SPEAKERS (OFF/A/B/A+B)
repeatedly to select the front speaker
system you want to use.
You can record on a cassette tape or MiniDisc
using the receiver. See the operating instructions
of your cassette deck or MD deck if you need
help.
The selected speaker system appears in the
display. To turn off the speaker output, press
SPEAKERS (OFF/A/B/A+B) repeatedly until
“SP.A” and “SP.B” indication turn off.
1
2
Select the component to be recorded.
Prepare the component for playing.
The speaker system
• SP.A
For example, insert a CD into the CD
player.
The speakers connected to the SPEAKERS
FRONT A terminals.
• SP.B
The speakers connected to the SPEAKERS
FRONT B terminals.
• SP.A and SP.B
The speakers connected to both the
SPEAKERS FRONT A and B terminals
(parallel connection).
3
4
Insert a blank tape or MD into the
recording deck and adjust the
recording level, if necessary.
Start recording on the recording deck,
then start playback on the playback
component.
Notes
• You cannot record a digital audio signal using a
component connected to the analog MD/TAPE OUT
jacks. To record a digital audio signal, connect a
digital component to the DIGITAL OPTICAL MD/
TAPE OUT jacks.
• Sound adjustments do not affect the signal output
from the MD/TAPE OUT jacks.
• The analog audio signals of the current input is
output from the MD/TAPE OUT jacks.
• The signals input to the MULTI CH IN 1 or 2 jacks
are not output from the MD/TAPE OUT jacks even
when MULTI CH IN 1 or 2 is being used. The analog
audio signals of the current or previously used input
are output.
• Some sources contain copy guards to prevent
recording. In this case, you may not be able to record
from the sources.
40GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording on a video tape
Listening to the sound in
another zone
You can record from a VCR, a TV or a DVD
using the receiver. You can also add audio from
a variety of audio sources when editing a video
tape. See the operating instructions of your VCR
or DVD player if you need help.
Y
1
2
Select the program source to be
recorded.
S-VIDEO
OUT
S-VIDEO
IN
S-VIDEO
OUT
S-VIDEO
IN
P
B/CB
/B–Y
P
R/CR
/R–Y
Prepare the component for playing.
VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT VIDEO IN
VIDEO OUT
TV/SAT
IN
DVD
IN
MONITOR
OUT
L
L
CTRL
L
For example, insert a video tape you want to
record into VCR.
MONITOR A1 II
COMPONENT VIDEO
SU
R
R
R
R
SUB
AUDIO IN
AUDIO OUT AUDIO IN
AUDIO OUT AUDIO IN
WOOFER
3
4
Insert a blank video tape into the VCR
(VIDEO 1 or VIDEO 2) for recording.
DVD
VIDEO 2
VIDEO 1
L
PRE OUT
L
L
+
–
CENTER
CENTER
L
Start recording on the recording VCR,
then start playing the video tape or
DVD you want to record.
R
R
R
R
R
SUB
SURR
BACK
SUB
SURR
S
FRONT SURROUND
OUT
WOOFER
FRONT SURROUND
WOOFER
MULTI CH IN 2
MULTI CH IN 1
2ND ZONE
Tip
You can record the sound from any audio source onto
a video tape while copying from a video tape or DVD.
Locate the point where you want to start recording
from another audio source, select the program source,
then start playback. The audio from that source will be
recorded onto the audio track of the video tape instead
of the audio from the original medium. To resume
audio recording from the original medium, select the
video source again.
2ND ZONE
You can select analog audio signals for output to
the 2nd zone.
Press 2ND ZONE repeatedly to select the
analog audio signals for output to a stereo
amplifier in another room.
Each time you press the button, the audio source
changes cyclically as follows:
SOURCE t MD/TAPE t SA-CD/CD
Notes
*1
• You cannot record a digital audio signal using a
component connected to the analog VIDEO 1
AUDIO OUT or VIDEO 2 AUDIO OUT jacks.
• Make sure to make both digital and analog
connections to the TV/SAT and DVD inputs. Analog
recording is not possible if you make only digital
connections.
*2
t TUNER
*1
The audio signals of the current INPUT
SELECTOR is output.
*2
The audio signals of the last selected TUNER
function (AM/FM) is output.
Tips
• The analog audio signals of the current input are
output from the VIDEO 1 AUDIO OUT or VIDEO 2
AUDIO OUT jacks.
• Only signals from components connected to the
analog input jacks are output through the 2ND ZONE
OUT jacks. No signals are output from components
connected to only the digital input jacks.
• When “SOURCE” is selected, the signals input to the
MULTI CH IN 1 or 2 jacks are not output from the
2ND ZONE OUT jacks even when MULTI CH IN 1
or 2 is selected. The analog audio signals of the
current function are output.
• The signals input to the MULTI CH IN 1 or 2 jacks
are not output from VIDEO 1 AUDIO OUT or
VIDEO 2 AUDIO OUT jacks even when MULTI
CH IN 1 or 2 is being used. The analog audio signals
of the current or previously used input are output.
continued
41GB
Download from Www.Somanuals.com. All Manuals Search And Download.
2nd zone connections
CONTROL A1II Control
Main receiver
System
Audio/video components
The CONTROL A1II Control System was
designed to simplify the operation of audio
systems composed of separate Sony
components. CONTROL A1II connections
provide a path for the transmission of control
signals which enable automatic operation and
control features usually associated with
integrated systems.
Currently, CONTROL A1II connections
between a Sony CD player, amplifier (receiver),
MD deck and cassette deck provide automatic
function selection.
STR-DE897
2ND
ZONE
OUT
2nd zone
Note
Speaker
Speaker
Do not operate a 2 way remote control unit when the
CONTROL A1II jacks are connected via a PC
interface kit to a personal computer running “MD
Editor” or similar application. Also, do not operate the
connected component in a manner contrary to the
functions of the application, as this may cause the
application to operate incorrectly.
Amplifier/Receiver
CONTROL A1II and CONTROL A1
compatibility
The CONTROL A1 control system has been updated
to the CONTROL A1II which is the standard system in
the Sony 300 disc CD changer and other recent Sony
components. Components with CONTROL A1 jacks
are compatible with components with CONTROL
A1II, and can be connected to each other. Basically,
the majority of the functions available with the
CONTROL A1 control system will be available with
the CONTROL A1II control system.
However, when making connections between
components with CONTROL A1 jacks and
components with CONTROL A1II jacks, the number
of functions that can be controlled may be limited
depending on the component. For detailed information,
refer to the operating instructions supplied with the
component(s).
If you have a Sony CD changer with a
COMMAND MODE selector
If your CD changer’s COMMAND MODE
selector can be set to CD 1, CD 2, or CD 3, be
sure to set the command mode to “CD 1” and
connect the changer to the CD jacks on the
amplifier (receiver).
42GB
Download from Www.Somanuals.com. All Manuals Search And Download.
If, however, you have a Sony CD changer with
VIDEO OUT jacks, set the command mode to
“CD 2” and connect the changer to the VIDEO
2 jacks on the amplifier (receiver).
Connections
You can connect up to 10 CONTROL A1II
compatible components in any order. However,
you can connect only one of each type of
component (i.e., 1 CD player, 1 MD deck, 1 tape
deck and 1 receiver).
(You may be able to connect more than one CD
player or MD deck, depending on the model.
Refer to the operating instructions supplied with
the respective component for details.)
Example
MD
deck
Tape
deck
CD
player
Other
components
Amplifier
(Reciever)
In the CONTROL A1II control system, the
control signals flow both ways, so there is no
distinction of IN and OUT jacks. If a component
has more than one CONTROL A1II jack, you
can use either one, or connect different
components to each jack.
Some CONTROL A1 compatible components
are supplied with a connecting cord as an
accessory. In this case, use the connecting cord
for your connection.
When using a commercially available cord, use
a monaural mini-plug cord less than 2 meters
long, with no resistance.
Basic Functions
The input selector on the receiver automatically
switches to the correct input when you press the
play button on one of the connected components
(Auto input selection).
The CONTROL A1II functions will operate as
long as the component you want to operate is
turned on, even if all of the other connected
components are not turned on.
Note
When recording, do not play any components other
than the recording source. It will cause the automatic
input selection to operate.
43GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations Using the Remote RM-PG413
You can use the remote RM-PG413 to operate
the components in your system.
Remote button
description
Before you use your
remote
qj
qk
1
TV ?/1
AV ?/1
P
?/1
L
RM SET UP
2
3
SYSTEM STANDBY SLEEP
VIDEO1 VIDEO2 VIDEO3 DVD
Inserting batteries into the
remote
ql
w;
wa
4
5
6
7
8
AV1
TV/SAT
AV2
TAPE
2ND
MD/DAT SA-CD/CD
Insert R6 (size-AA) batteries with the + and –
properly oriented in the battery compartment.
When using the remote, point it at the remote
M1
M2
ws
wd
wf
TUNER PHONO MULTI CH SOURCE
sensor
on the receiver.
2CH
A.F.D.
DIRECT
ANGLE
MOVIE
DUAL
MUSIC
SB
1
4
7
2
5
8
3
TEST
TONE
wg
wh
MONO DECODING
9
6
JUMP/
TIME
PRESET/
CH/D.SKIP
AUDIO
9
wj
SUBTITLE ENTER
.
>
q;
qa
qs
0/10
>10/11
12
wk
wl
e;
ea
SHIFT D.TUNING
DISC
ALT
-
m
M
ANT
CLEAR SEARCH MODE
Tip
Under normal conditions, the batteries should last for
about 6 months. When the remote no longer operates
the receiver, replace all batteries with new ones.
X
x
H
TOP MENU/
GUIDE
MUTING
qd
AV MENU
es
MASTER
VOL
Notes
F
f
• Do not leave the remote in an extremely hot or humid
place.
G
g
qf
ed
• Do not use a new battery with an old one.
• Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a
malfunction.
O
ENTER
DISPLAY
TV VOL
RETURN/EXIT
TV/
ef
eg
MAIN
MENU
TV CH
VIDEO
qg
qh
• If you do not use the remote for an extended period
of time, remove the batteries to avoid possible
damage from battery leakage and corrosion.
WIDE DIMMER
eh
ej
The tables below show the settings of each
button.
Remote
Button
Operations Function
A.F.D. 9 Receiver
Selects the decoding
mode for audio sound.
44GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
Button
Operations
Function
Remote
Button
Operations
Function
ALT wl
Remote
When ALT button
DUAL
MONO 9
Receiver
Selects the language
you want during digital
broadcast.
lights up, it changes
remote key function to
activate those buttons
with orange printing.
DVD w;
Receiver
To watch DVD.
ENTER qf Receiver/
Enters the selection.
ANGLE 9 DVD player Selects viewing angle
VCR/
Satellite tuner/
or changes the angles.
ANT qa
VCR
Selects output signal
from the antenna
terminal: TV signal or
VCR program.
DVD player
ENTER wk TV/VCR/
After selecting a
Satellite tuner/ channel, disc or track
LD player/
MD deck/
DAT deck/
Tape deck
using the numeric
buttons, press to enter
the value.
AUDIO 9 TV/VCR/
Changes the sound to
DVD player Multiplex, Bilingual
or Multi channel TV
Sound.
JUMP/
TIME 9
Satellite tuner Toggles between the
previous and the
AV MENU VCR/
qf
Displays menu.
Satellite tuner/
DVD player
current channels.
CD player/
Shows the time or
AV 14 and Remote
AV 2 3
Select the command
mode of the remote.
VCD player/ displays the playing
DVD player/ time of disc, etc.
MD deck
AV ?/1 qj TV/VCR/
Turns the audio and
video components on
CD player/
VCD player/ or off.
LD player/
DVD player/
MD deck/
MAIN
MENU eg
Receiver
Receiver
Receiver
Selects the menu of the
receiver.
MASTER
VOL +/– ed
Adjusts the master
volume of the receiver.
MD/DAT
wa
To listen to Minidisc or
DAT deck.
DAT deck
CLEAR qa DVD player Press if you make a
mistake when you
MOVIE 9 Receiver
Selects the pre-
programmed sound
fields for movie.
press the numeric
button or press to
return to continuous
play etc.
MULTI CH Receiver
wf
Selects MULTI CH IN
1/2 source.
DIMMER
eh
Receiver
Adjusts the brightness
of the display.
MUSIC wg Receiver
Selects the pre-
programmed sound
fields for music.
DIRECT 9 Receiver
Selects ANALOG
DIRECT.
MUTING
Receiver
Mutes the sound from
the receiver.
es
DISC e;
CD player/
VCD player
Selects a disc directly
(multi-disc changer
only).
M1 6 and Remote
M2 5
To perform several
commands in sequence
automatically.
DISPLAY
TV/VCR/
Selects information
qf
VCD player/ displayed on the TV
PHONO 8 Receiver
To listen to turntable.
Selects preset stations.
Selects preset
LD player/
screen.
PRESET/
Receiver
DVD player
CH/
TV/VCR/
D.TUNING Receiver
qa
Enters direct tuning
mode.
D.SKIP +/– Satellite tuner channels.
wj CD player/ Skips discs (multi-disc
VCD player/ changer only).
DVD player/
MD deck
continued
45GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
Button
Operations Function
Remote
Button
Operations Function
TV Adjusts the volume of
RETURN/ VCD player/ Returns to the previous
TV VOL
EXIT qf
LD player/
menu.
+/– qg
the TV.
DVD player
TV ?/1 2 TV
Turns the TV on or off.
Satellite tuner Exits the menu.
VIDEO1
4
Receiver
To watch VCR.
(VTR mode 3)
RM SET UP Remote
Set up the remote.
1
VIDEO2
3
Receiver
Receiver
To watch VCR.
(VTR mode 1)
SA-CD/CD Receiver
ws
To listen to Super Audio
CD or compact disc.
VIDEO3
ql
To watch VCR.
(VTR mode 2)
SB
Receiver
Selects the surround
back decoding modes.
DECODING
wh
WIDE ej TV
Selects the wide picture
mode.
SEARCH
MODE e;
DVD player Selects searching mode.
Press to select the unit
for search (track, index,
etc.)
?/1 qk
Receiver
Turns the receiver on or
off.
2CH 9
Receiver
Selects 2CH STEREO
mode.
SHIFT qa Receiver
Selects a memory page
for presetting radio
stations or tuning to
preset stations.
V/v qf
Receiver
Receiver
Selects a menu item.
B/b qf
Adjusts or changes the
setting.
SLEEP qk Receiver
Activates the sleep
function and the
duration which the
receiver turns off
automatically.
1-9 9 and Receiver
0/10 q;
Use with SHIFT to
preset radio station or
tuning to preset stations
and with D.TUNING
for direct tuning.
SOURCE wd Remote
Selects 2ND ZONE
output.
CD player/
VCD player/ 0/10 selects track 10.
Selects track numbers.
LD player/
MD deck/
DAT deck
SUBTITLE DVD player Changes the subtitles.
q;
SYSTEM
STANDBY TV/VCR/
Receiver/
Turns off the receiver
and other Sony audio/
TV/VCR/
Satellite tuner numbers.
>10/11 q; CD player/ Selects track numbers
Selects channel
(Press AV Satellite tuner/ video components.
?/1 qj and CD player/
?/1 qk at VCD player/
VCD player/ over 10.
LD player/
MD deck
the same
time)
LD player/
DVD player/
MD deck/
./> VCR/
Skips tracks.
DAT deck
q;
CD player/
VCD player/
DVD player/
LD player/
MD deck/
TAPE 5
Receiver
Receiver
To listen to audio tape.
Outputs test tone.
TEST
TONE 9
TOP MENU/ DVD player Displays DVD title.
DAT deck/
Tape deck
GUIDE qf Satellite tuner Displays guide menu.
TUNER 7 Receiver
To listen to radio
programs.
m/M CD player/
Searches tracks in the
qa
VCD player/ forward or backward
DVD player direction.
LD player/
TV CH +/– TV
qh
Selects preset TV
channels.
MD deck
TV/SAT 6 Receiver
To watch TV programs
or satellite receiver.
VCR/
Fastforwards or
rewinds.
DAT deck/
Tape deck
TV/VIDEO TV
ef
Selects input signal: TV
input or video input.
46GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote
Button
Operations
Function
Selecting the command
mode of the remote
H qs
VCR/
Starts playback.
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
Set the remote command mode using the RM
SET UP button and the remote command mode
buttons.
Selecting the command mode
X qd
VCR/
CD player/
VCD player/ recording with
LD player/
DVD player/ standby.)
MD deck/
DAT deck/
Pauses playback or
record. (Also start
You can switch the command mode (AV1 and
AV2) of the remote. If the command mode of the
receiver and the remote is different, you cannot
use the remote to operate the receiver.
components in record
Press AV1 or AV2 while holding down RM
SET UP.
Tape deck
The indicator flashes once (twice for AV2) ,
then the command mode switches.
x ea
VCR/
Stops playback.
CD player/
VCD player/
LD player/
DVD player/
MD deck/
DAT deck/
Tape deck
To check the command mode of
the remote
Press RM SET UP. You can check the remote by
the indicator.
O qf
VCD player/ Returns to the previous
Mode
AV1
AV2
Indicator flashes
LD player/
menu or exits the menu.
once
DVD player
twice
V/v/B/b
qf
VCR/
Selects a menu item.
Satellite tuner/
DVD player
To reset the remote to factory
settings
-/-- e;
TV
Selects the channel
entry mode, either one
or two digit.
Press ?/1, AV ?/1 and MASTER VOL – at
the same time.
2ND ql
Remote
Selects the command
mode of the remote.
The indicator flashes 3 times, then goes off.
Note
Notes
If the command mode of the receiver and the remote is
different, you cannot use the remote to operate the
receiver. To change the command mode of the
receiver, see page 57.
• Some functions explained in this section may not
work depending on the model.
• The above explanation is intended to serve as an
example only. Therefore, depending on the
component the above operation may not be possible
or may operate differently than described.
• To activate the buttons with orange printing, press
ALT first before pressing the buttons.
• When you press input buttons (VIDEO1, VIDEO2,
VIDEO3 or DVD), the input mode of the TV might
not switch to the corresponding input mode that you
want. In this case, press TV/VIDEO button to switch
the input mode of the TV.
• The 2ND button on the remote is not available for
receiver operation.
47GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To cancel programming
Programming the remote
Press RM SET UP during any step. The remote
automatically exits the programming mode.
You can program the remote to control non-
Sony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
To activate the input after
programming
Press the programmed button to activate the
input you want.
Furthermore, you can also program the remote
for Sony components that the remote is unable to
control. Note that the remote can only control
components that accept infrared wireless control
signals.
If programming is unsuccessful,
check the following:
• If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
• If the indicator flashes 4 times in quick
an error has occurred. Start again from step 1.
1
Press AV ?/1 while holding down RM
SET UP.
The indicator lights up.
Notes
2
Press the input button (including TV
?/1) for the component you want to
control.
• The indicator turns off while a valid button is
pressed.
• In step 2, if several input buttons are pressed, only the
last pressed button is valid.
For example, if you are going to control a
CD player, press SA-CD/CD.
• In step 2, if you press TV ?/1, only TV VOL +/– ,
TV CH +/–, TV/VIDEO and WIDE buttons are
reprogrammed.
3
Press the numeric buttons to enter the
more than one code exists)
corresponding to the component and
the maker of the component you want
to control.
• In step 3, if an input button is pressed, the new input
is selected and the programming procedure returns to
the beginning of step 3.
• For the numeric codes, only the first three numbers
entered are valid.
See the tables on pages 49–50 for
information on the numeric code(s)
corresponding to the component and the
maker of the component (the first digit and
the last two digits of the numeric code
correspond to the category and the maker’s
code respectively.)
To clear the memory of the
remote
To clear all programmed and learned signals, do
the following to reset the remote to factory
settings.
Press ?/1, AV ?/1 and MASTER VOL – at
the same time.
4
5
Press ENTER.
Once the numeric code has been verified,
the indicator slowly flashes twice and the
remote automatically exits the
The indicator flashes 3 times, then goes off.
programming mode.
Repeat steps 1 to 4 to control other
components.
48GB
Download from Www.Somanuals.com. All Manuals Search And Download.
The numeric codes
To control a DAT deck
corresponding to the component
and the maker of the component
Maker
Code(s)
203
SONY
Use the numeric codes in the tables below to
control non-Sony components and also Sony
components that the remote is normally unable
to control. Since the remote signal that a
component accepts differs depending on the
model and year of the component, more than one
numeric code may be assigned to a component.
If you fail to program your remote using one of
the codes, try using other codes.
PIONEER
219
To control an MD deck
Maker
Code(s)
301
SONY
DENON
JVC
302
303
KENWOOD
304
Notes
• The numeric codes are based on the latest
information available for each brand. There is a
chance, however, that your component will not
respond to some or all of the codes.
To control a tape deck
Maker
Code(s)
201, 202
204, 205
206, 207, 208, 209
210
SONY
• All of the input buttons on this remote may not be
available when used with your particular component.
DENON
KENWOOD
NAKAMICHI
PANASONIC
PHILIPS
To control a CD player
Maker
Code(s)
101, 102, 103
104, 123
105, 106, 107
108, 109, 110
111, 116
116
216
SONY
211, 212
213, 214
215, 216
217, 218
DENON
PIONEER
TECHNICS
YAMAHA
JVC
KENWOOD
MAGNAVOX
MARANTZ
ONKYO
To control an LD player
112, 113, 114
115
Maker
Code(s)
601, 602, 603
606
PANASONIC
PHILIPS
SONY
116
PIONEER
PIONEER
TECHNICS
YAMAHA
117
115, 118, 119
120, 121, 122
To control a video CD player
Maker
Code(s)
SONY
605
continued
49GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To control a VCR
To control a TV
Maker
Code(s)
Maker
Code(s)
SONY
701, 702, 703, 704, 705,
706
SONY
501, 502
DAEWOO
504, 505, 506, 507, 515,
544
AIWA*
710, 750, 757, 758
707, 708, 709, 759
740
AKAI
FISHER
508
BLAUPUNKT
EMERSON
GOLDSTAR
503, 511, 512, 515, 534,
544
711, 712, 713, 714, 715,
716, 750
GRUNDIG
HITACHI
517, 534
FISHER
717, 718, 719, 720
721, 722, 730
723, 753
513, 514, 515, 544
521, 522
GENERAL ELECTRIC
GOLDSTAR
GRUNDIG
ITT/NOKIA
JVC
516
724
MAGNAVOX
MITSUBISHI/MGA
NEC
503, 518, 544
503, 519, 544
503, 520, 544
509, 524
HITACHI
722, 725, 729, 741
717
ITT/NOKIA
JVC
726, 727, 728, 736
730, 731, 738
732, 733, 734, 735
736
PANASONIC
PHILIPS
MAGNAVOX
MITSUBISHI/MGA
NEC
515, 518
PIONEER
509, 525, 526, 540
510, 527, 528, 529, 544
RCA/PROSCAN
SAMSUNG
PANASONIC
729, 730, 737, 738, 739,
740
503, 515, 531, 532, 533,
534, 544
PHILIPS
729, 730, 731
729
SANYO
508, 545, 546, 547
535
PIONEER
SHARP
RCA/PROSCAN
722, 729, 730, 731, 741,
747
TELEFUNKEN
THOMSON
TOSHIBA
ZENITH
523, 536, 537, 538
530, 537, 539
535, 540, 541
542, 543
SAMSUNG
SANYO
742, 743, 744, 745
717, 720, 746
748, 749
SHARP
TELEFUNKEN
TOSHIBA
ZENITH
751, 752
To control a satellite tuner or
cable box
747, 755, 756
754
Maker
Code(s)
SONY
801, 802, 803, 804
* If an AIWA VCR does not work even though you
enter the code for AIWA, enter the code for Sony
instead.
JERROLD/G.I.
806, 807, 808, 809, 810,
811, 812, 813, 814
PANASONIC
RCA
818
To control a DVD player
805, 819
815, 816, 817
Maker
Code(s)
401, 402, 403
406, 408
407
S. ATLANTA
SONY
To control a tuner
PANASONIC
PHILIPS
PIONEER
TOSHIBA
DENON
Maker
Code(s)
409
SONY
002, 003, 004, 005
404
405
50GB
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press the appropriate button on the
remote control to be learned to send
the remote button code.
Learning the commands of
your components
Lightly pressing the button once should be
sufficient.
By using the Learning function, it is possible for
this remote to perform learned commands.
If learning is completed successfully, the
indicator slowly flashes twice and the
mode.
When learning is not completed
successfully, the indicator flashes 4 times in
quick succession and the procedure returns
to step 5.
If the memory of the remote is already full,
the indicator flashes 8 times in quick
succession and the remote automatically
exits the learning mode.
Setting remote control codes
that are not stored in the remote
When a remote control code is not one of the
presets stored in the remote, it is possible for the
remote to learn the code using the Learning
function.
1
Press TV ?/1 while holding down
RM SET UP.
The indicator lights up.
Notes
2
Press the input button (including TV
?/1) for the component you want to
control.
• You can program more than 80 keys for the Learning
function. In some cases, you may not be able to
program even if you have not programmed 80
buttons. The number of buttons you can program for
each input button are shown in the following table.
For example, if you are going to learn an
operation for a CD player, press SA-CD/
CD.
Input button area
Number of Buttons
you can program
3
4
Press the button you want to use for
the Learning function.
VIDEO 1, VIDEO 2,
DVD
78 keys
78 keys
78 keys
The indicator turns off while a valid button
is pressed, then flashes slowly.
VIDEO 3, TV/SAT,
TAPE
Point the remote control code receiver
section of the remote towards the
receiver/transmitter on the remote
control to be learned.
MD/DAT, SA-CD/CD,
TUNER
PHONO, MULTI CH
52 keys
7 keys
TV buttons, (TV ?/1,
TV VOL +/– , TV CH +/–,
WIDE, TV/VIDEO
5–10 cm
button is pressed.
• In step 3, if several buttons that can be used for
learning are pressed, only the last pressed button is
valid. The indicator flashes slowly, it turns on while
a valid button is pressed.
• In step 5, if a button that can be used for learning is
pressed, the new button is selected and the learning
procedure returns to the beginning of step 5.
continued
51GB
Download from Www.Somanuals.com. All Manuals Search And Download.
To activate the input after
programming
Performing several
commands in sequence
automatically
Press the programmed button to activate the
input you want.
To cancel learning
(Macro Play)
Press RM SET UP during any step. The remote
automatically exits the learning mode.
The Macro Play function lets you link several IR
codes in a sequential order as a single command.
The remote provides 2 macro lists (M1 and M2).
You can specify up to 10 IR codes for each
macro list.
To clear the learned codes
Start over from step 1. After step 3, press
TV ?/1 for more than 2 seconds. The indicator
lights up twice slowly and the learned code is
cleared. If TV ?/1 is pressed less than 2
seconds, the learning procedure returns to the
beginning of step 5.
When a learned code is cleared, if the button was
previously programmed for another input
selector, the programmed code for that button
can be used.
Setting the sequence of IR codes
1
Press M1 (or M2) while holding down
RM SET UP.
The indicator lights up.
2
Press the numeric buttons to select the
macro step number.
To clear the memory of the
remote
For example, to program step 1, press 1.
The indicator flashes slowly.
To clear all programmed and learned signals, do
the following to reset the remote to factory
settings.
3
4
Point the remote control code receiver
section of the remote towards the
receiver/transmitter on the remote
control to be learned.
Press ?/1, AV ?/1 and MASTER VOL – at
the same time.
Press the appropriate button on the
remote control to be learned to send
the remote button code.
The indicator flashes 3 times, then goes off.
To use a command that has been
learned
Lightly pressing the button once should be
sufficient.
When selecting a learned input, press the learned
button for that input.
If learning is completed successfully, the
indicator slowly flashes twice and the
mode.
When learning is not completed
successfully, the indicator flashes 4 times in
quick succession and the procedure returns
to step 4.
5
Repeat steps 1 through 4 to program
up to 10 IR codes.
52GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
If programming is unsuccessful, check the following:
– If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
– If the indicator lights up 4 times in quick
succession in step 3, an error has occurred. Start
again from step 1.
To cancel programming
Press RM SET UP during any step. The remote
automatically exits the macro setting mode.
To delay the output of an IR code
Start over from step 1. In step 3,
• Press M1 (TV/SAT) when the macro setting
is M1.
• Press M2 (TAPE) when the macro setting is
M2.
1 second delay is programmed at this program
step. The indicator lights up twice slowly, then
the remote automatically exits the macro setting
mode.
To clear the programmed IR
codes
Clear each macro step individually. In step 3,
• Press M1 (TV/SAT) when the macro setting
is M1.
• Press M2 (TAPE) when the macro setting is
M2.
The IR code is cleared. The indicator lights up
twice slowly, then the remote automatically
exits the macro setting mode.
To start macro play
ALT indicator turns on.
Note
If the Macro Play function does not work properly,
program a delay between each operation. See “To
delay the output of an IR code”.
53GB
Download from Www.Somanuals.com. All Manuals Search And Download.
On cleaning
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
Additional Information
Precautions
On safety
Should any solid object or liquid fall into the cabinet,
unplug the receiver and have it checked by qualified
personnel before operating it any further.
If you have any question or problem concerning your
receiver, please consult your nearest Sony dealer.
On power sources
• Before operating the receiver, check that the
operating voltage is identical with your local power
supply. The operating voltage is indicated on the
nameplate at the rear of the receiver.
• The receiver is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the receiver itself has been turned off.
• If you are not going to use the receiver for a long
time, be sure to disconnect the receiver from the wall
outlet. To disconnect the AC power cord, grasp the
plug itself; never pull the cord.
• (Models of area code U, CA only)
One blade of the plug is wider than the other for the
purpose of safety and will fit into the wall outlet only
one way. If you are unable to insert the plug fully into
the outlet, contact your dealer.
• AC power cord must be changed only at the qualified
service shop.
On heat buildup
Although the receiver heats up during operation, this is
not a malfunction. If you continuously use this receiver
at a large volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid burning
yourself, do not touch the cabinet.
On placement
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and prolong the
life of the receiver.
• Do not place the receiver near heat sources, or in a
place subject to direct sunlight, excessive dust or
mechanical shock.
• Do not place anything on top of the cabinet that
might block the ventilation holes and cause
malfunctions.
• Use caution when placing the receiver on surfaces
that have been specially treated (with wax, oil,
polish, etc.) as staining or discoloration of the surface
may result.
On operation
Before connecting other components, be sure to turn
off and unplug the receiver.
54GB
Download from Www.Somanuals.com. All Manuals Search And Download.
There is no sound from analog 2 channel
sources.
• Check that the DIGITAL ASSIGN function is not
used to assign the audio input of other input to the
selected input (page 34).
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem.
• Check that the INPUT MODE is not set to
“COAX FIXED” or “OPT FIXED” (page 35).
• Check that you have not selected MULTI CH IN
1 or 2.
There is no sound or only a very low-level
sound no matter which component is
selected.
• Check that the speakers and components are
connected securely.
COAXIAL or OPTICAL input jack).
• Check that the DIGITAL ASSIGN function is not
used to assign the audio input of other input to the
selected input (page 34).
• Check that both the receiver and all components
are turned on.
• Check that the INPUT MODE is not set to
“ANALOG FIXED” (page 35). Check that the
INPUT MODE is not set to “COAX FIXED” for
the sources from OPTICAL input jack, or set to
“OPT FIXED” for the sources from COAXIAL
input jack.
• Check that you have selected the correct
component on the receiver.
• Check that MASTER VOLUME –/+ is not set at
“VOLUME MIN”.
• Check that the SPEAKERS (OFF/A/B/A+B) is
not set to off (page 40).
• Check that you have not selected MULTI CH IN
1 or 2.
• Check that the headphones are not connected.
• Press MUTING on the remote to cancel the
muting function.
The left and right sounds are unbalanced or
reversed.
• Check that the speakers and components are
connected correctly and securely.
There is no sound from a specific component.
• Check that the component is connected correctly
to the audio input jacks for that component.
• Check that the cord(s) used for the connection is
(are) fully inserted into the jacks on both the
receiver and the component.
• Adjust balance parameters in the LEVEL menu.
There is severe hum or noise.
• Check that the speakers and components are
connected securely.
• Check that you have selected the correct
component on the receiver.
• Check that the connecting cords are away from a
transformer or motor, and at least 3 meters (10
feet) away from a TV set or fluorescent light.
• Move your TV away from the audio components.
• Make sure you have grounded U SIGNAL GND
terminal (only when a turntable is connected).
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the PHONES
jack to verify that sound is output from the
headphones. If only one channel is output from the
headphones, the component may not be connected
to the receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both channels are
output from the headphones, the front speaker
may not be connected to the receiver correctly.
Check the connection of the front speaker which is
not outputting any sound.
There is no sound from the surround back
speakers.
• Some discs have no Dolby Digital EX flag even
though the packages have Dolby Digital EX
logos. In this case, select “MATRIX” (page 38).
continued
55GB
Download from Www.Somanuals.com. All Manuals Search And Download.
There is no sound or only a very low-level
sound is heard from the center/surround/
surround back speakers.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied) to
connect the receiver to an outdoor FM antenna as
shown below. If you connect the receiver to an
outdoor antenna, ground it against lightning. To
prevent a gas explosion, do not connect the ground
wire to a gas pipe.
• Select a CINEMA STUDIO EX mode (page 30).
• Adjust the speaker level (page 21).
• Make sure the center/surround speakers size
parameter are set to either “SMALL” or
“LARGE” (pages 18 and 19).
Outdoor FM antenna
Receiver
• Make sure the surround back speakers selection is
set to either “DUAL” or “SINGLE”.
ANTENNA
There is no sound from the sub woofer.
• Check that the sub woofer is connected correctly
and securely.
AM
Ground wire
(not supplied)
• Make sure the sub woofer selection parameter is
set to “YES” (page 18).
• There is no sound output from the SUB WOOFER
depending on the sound field.
To ground
The surround effect cannot be obtained.
• Make sure the sound field function is on (press
A.F.D., MOVIE or MUSIC).
Radio stations cannot be tuned in.
• Check that the antennas are connected securely.
Adjust the antennas and connect an external
antenna if necessary.
• Sound fields do not function for the signals with a
sampling frequency of more than 48 kHz.
Dolby Digital or DTS multi channel sound is
not reproduced.
• Check that the playing DVD, etc. is recorded in
Dolby Digital or DTS format.
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use direct
tuning.
• Make sure you set the tuning interval correctly
(when tuning in AM stations with direct tuning).
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
preset stations). Preset the stations (page 24).
• Press DISPLAY repeatedly so that the frequency
appears in the display.
• When connecting the DVD player, etc. to the
digital input jacks of this receiver, check the audio
setting (settings for the audio output) of the
connected component.
Recording cannot be done.
• Check that the components are connected
correctly.
There is no picture or an unclear picture
appears on the TV screen or monitor.
• Select the appropriate input on the receiver.
• Set your TV to the appropriate input mode.
• Move your TV away from the audio components.
• Select the source component with INPUT
SELECTOR.
• Make sure that INPUT MODE is set to
“ANALOG FIXED” (page 35) before recording
from a digital component connected to the analog
MD/TAPE jacks.
The DIGITAL OPTICAL MD/TAPE OUT jack
flashes red.
• When “AUTO 2CH” is selected for INPUT
MODE, the jack flashes red when no digital audio
signal is input. This depends on the INPUT
MODE function, and is not a malfunction.
• Make sure that INPUT MODE is set to “COAX
FIXED” or “OPT FIXED” (page 35) before
recording from a digital component connected to
the DIGITAL OPTICAL MD/TAPE OUT jack.
56GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
If you are unable to remedy the
problem using the
troubleshooting guide
The remote does not function.
• Point the remote at the remote sensor
receiver.
on the
Clearing the receiver’s memory may remedy the
problem (page 17). However, note that all
memorized settings will be reset to their factory
settings and you will have to readjust all settings
on the receiver.
• Remove any obstacles in the path between the
remote and the receiver.
• Replace all the batteries in the remote with new
ones, if they are weak.
• Check if the command modes of the receiver and
the remote is the same. If the command mode of
the receiver and the remote is different, you
cannot operate the receiver with the remote. To
switch the command mode of the receiver, press
?/1 to turn off the power. Then, press ?/1 while
pressing ENTER. Each time you press ?/1, the
command mode switches between “COM MODE
AV2” and “COM MODE AV1”. (The initial
setting is “COM MODE AV2”.)
If the problem persist
Consult your nearest Sony dealer.
Reference sections for clearing
the receiver’s memory
To clear
See
All memorized settings
Customized sound fields
page 17
page 36
• Make sure you select the correct input on the
remote.
• To activate the buttons with orange printing, press
ALT first before pressing the buttons.
• Before you use the V/v/B/b button for receiver
operation, press MAIN MENU. To operate other
components, press TOP MENU/GUIDE or AV
MENU after pressing the input button.
Error messages
If there is a malfunction, the display shows a
message. You can check the condition of the
receiver by the message. Refer to the following
table to solve the problem.
DECODE ERROR
Appears when the signal which the receiver cannot
decode (ex. DTS-CD) is input when “DEC. PRI.
XXXX” is set to “DEC. PRI. PCM”. Set to “DEC.
PRI. AUTO”.
PROTECTOR
Irregular current is output from the speakers. The
receiver will automatically turn off after a few
seconds. Check the speaker connection and turn on
the power again. If this problem persists, turn off the
receiver and consult your nearest Sony dealer.
57GB
Download from Www.Somanuals.com. All Manuals Search And Download.
1)
Measured under the following conditions:
Specifications
Area code
U, CA
E2/E3
AR
Power requirements
120 V AC, 60 Hz
240 V AC, 50 Hz
230 V AC, 50 Hz
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(Models of area code U only)
2)
Depending on the sound field settings and the
source, there may be no sound output.
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 100 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
3)
Measured under the following conditions:
Area code
Power requirements
AR
220 V AC, 50 Hz
Frequency response
PHONO
Amplifier section
Power Output
Models of area code U, CA
Rated Power Output at Stereo Mode
(8 ohms 20 Hz – 20 kHz, THD 0.09%)
RIAA equalization curve
0.5 dB
MULTI CH IN 1, 2,
SA-CD/CD, TV/SAT,
MD/TAPE, DVD,
VIDEO 1, 2, 3
10 Hz – 70 kHz
+0.5/–2 dB (with sound
field and equalizer
bypassed)
1)
100 W + 100 W
1)
Reference Power Output
(8 ohms 20 Hz – 20 kHz, THD 0.09%)
2)
FRONT
:
100 W/ch
100 W
100 W/ch
100 W/ch
Inputs (Analog)
PHONO
2)
CENTER
:
Sensitivity: 8 mV
2)
SURR
:
Impedance: 50 kiloohms
2)
SURR BACK
:
4)
S/N : 86 dB
(8 ohms 1 kHz, THD 0.7%)
5)
(A, 8 mV
)
2)
FRONT
:
110 W/ch
110 W
110 W/ch
110 W/ch
2)
MULTI CH IN 1, 2,
SA-CD/CD, TV/SAT,
MD/TAPE, DVD,
VIDEO 1, 2, 3
Sensitivity: 500 mV
CENTER
:
2)
Impedance: 50 kiloohms
SURR
:
4)
2)
S/N : 96 dB
SURR BACK
:
5)
(A, 500 mV
)
Models of area code E2/E3
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7%)
4)
INPUT SHORT (with sound field and equalizer
bypassed).
1)
5)
110 W + 110 W
Weighted network, input level.
1)
Reference Power Output
(8 ohms 1 kHz, THD 10%)
Inputs (Digital)
2)
FRONT
:
130 W/ch
130 W
130 W/ch
130 W/ch
DVD, SA-CD/CD
(Coaxial)
Sensitivity: –
Impedance: 75 ohms
S/N: 100 dB
2)
CENTER
:
2)
SURR
:
2)
SURR BACK
:
(A, 20 kHz LPF)
TV/SAT, SA-CD/CD,
MD/TAPE, VIDEO 3
(Optical)
Sensitivity: –
Impedance: –
S/N: 100 dB
Models of area code AR
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7%)
1)
3)
(A, 20 kHz LPF)
110 W + 110 W
100 W + 100 W
1)
Outputs (Analog)
Reference Power Output
(8 ohms 1 kHz, THD 10%)
MD/TAPE (OUT),
VIDEO 1, 2
(AUDIO OUT)
Voltage: 500 mV
Impedance: 10 kiloohms
2)
FRONT
:
130 W/ch
130 W
130 W/ch
130 W/ch
2)
CENTER
:
2)
SURR
:
SUB WOOFER
Voltage: 2 V
Impedance: 1 kiloohms
2)
SURR BACK
:
58GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Outputs (Digital)
Video section
Inputs/Outputs
Video:
MD/TAPE (Optical)
Sensitivity: –
1 Vp-p, 75 ohms
S-video:
Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
Equalizer
Gain levels
10 dB, 0.5 dB step
COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms
PB/CB/B-Y: 0.7 Vp-p,
75 ohms
FM tuner section
PR/CR/R-Y: 0.7 Vp-p,
75 ohms
Tuning range
Antenna
Antenna terminals
Intermediate frequency
Sensitivity
Mono:
Stereo:
Useable sensitivity
S/N
87.5 - 108.0 MHz
FM wire antenna
75 ohms, unbalanced
10.7 MHz
80 MHz HD Pass Through
General
Power requirements
18.3 dBf, 2.2 µV/75 ohms
38.3 dBf, 22.5 µV/75 ohms
11.2 dBf, 1 µV/75 ohms
Area code
U, CA
E2/E3
AR
Power requirements
120 V AC, 60 Hz
120/220/240 V AC, 50/60 Hz
220–230 V AC, 50/60 Hz
Mono:
Stereo:
76 dB
70 dB
Harmonic distortion at 1 kHz
Power consumption
Mono:
0.3%
Stereo:
Separation
Frequency response
0.5%
Area code
U, E2/E3
CA
Power consumption
300 W
45 dB at 1 kHz
30 Hz – 15 kHz,
+0.5/–2 dB
410 VA
Selectivity
60 dB at 400 kHz
AR
260 W
AM tuner section
Tuning range
Power consumption (during standby mode)
0.3 W (when “POWER
SAVE” in the
CUSTOMIZE menu is set
to “ON”) (page 38)
Models of area code U, CA
6)
6)
With 10-kHz tuning scale: 530 – 1,710 kHz
With 9-kHz tuning scale: 531 – 1,710 kHz
Models of area code E2/E3
With 10-kHz tuning scale: 530 – 1,610 kHz
With 9-kHz tuning scale: 531 – 1,602 kHz
Models of area code AR
AC outlets
6)
6)
Area code
U, CA
AC outlets
2 switched, 120 W/1A MAX
1 switched, 100 W MAX
E2/E3
With 10-kHz tuning scale: 530 – 1,610 kHz
Antenna
Intermediate frequency
Usable sensitivity
Loop antenna
450 kHz
50 dB/m (at 1,000 kHz or
999 kHz)
Dimensions (w/h/d) (Approx.)
430 × 157.5 × 371 mm
(16 7/8 × 6 2/8 × 14 5/8
inches) including
projecting parts and
controls
S/N
54 dB (at 50 mV/m)
0.5% (50 mV/m, 400 Hz)
Harmonic distortion
Selectivity
At 9 kHz:
Mass (Approx.)
10.7 kg (23 lb 10 oz)
35 dB
40 dB
At 10 kHz:
Supplied accessories
6)
FM wire antenna (1)
AM loop antenna (1)
Remote commander RM-PG413 (1)
R6 (size-AA) batteries (2)
You can change the AM tuning scale to 9 kHz or 10
kHz. After tuning in any AM station, turn off the
receiver. While holding down PRESET TUNING +
or TUNING +, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the procedure.
For details on the area code of the component you
are using, see page 3.
Design and specifications are subject to change
without notice.
59GB
Download from Www.Somanuals.com. All Manuals Search And Download.
List of button locations and reference pages
Illustration number
How to use this page
r
Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.
DISPLAY 7 (25, 56)
R
R
Main unit
SPEAKERS (OFF/A/B/A+B) 6
(16, 40, 55)
M - O
ALPHABETICAL ORDER
MAIN MENU 5 (18, 35, 37, 39)
MASTER VOLUME –/+ qk (17,
21, 22, 55)
SURR BACK DECODING qj
(32)
A - I
A.F.D. (button/indicator) qf (29,
31, 56)
TUNER FM/AM (indicator) wd
(22)
MD/TAPE (indicator) wg (22)
DIMMER 8 (25)
TUNING +/– ef (23, 59)
TV/SAT (indicator) wh (22)
VIDEO 1 (indicator) e; (22)
VIDEO 2 (indicator) wl (22)
DISPLAY 7 (25, 56)
Display q; (25)
(30, 31, 56)
ENTER 9 (17, 18, 39, 57)
FM MODE 4 (23)
MULTI CHANNEL DECODING
(indicator) qa (23)
MULTI CH IN/DIRECT qs (23,
28)
INPUT MODE w; (35)
INPUT SELECTOR wa (22, 23,
24, 25, 35, 38, 39, 56)
IR (receptor) 3 (44, 57)
MUSIC(button/indicator) qh (31,
56)
NUMBERS AND SYMBOLS
2CH (button/indicator) qd (28,
31, 36)
P - Z
2ND ZONE ql (41)
–/+ ea (18, 35, 37, 39)
?/1 (power) 1 (17, 18, 21, 36,
57, 59)
PHONES (jack) eg (22, 55)
PHONO (indicator) ws (22)
PRESET TUNING +/– eh (24,
59)
</> es (18, 35, 37, 39)
SA-CD/CD (indicator) wf (22)
234567 8 9
q;
qa qs qd qf qg qh qj
1
es ea
eh egef
ed
e; wl wkwj wh wgwf wd ws
wa w;ql qk
60GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
Adjusting
CUSTOMIZE parameters 37
on a video tape 41
on an audio tape or MD 40
EQUALIZER parameter 37
LEVEL parameter 35
SET UP parameters 18
speaker level and balance 21
Automatic tuning 23
Selecting
component 22
front speaker system 40
sound field 30
SET UP menu 18
Sleep Timer 39
C
Changing
display 25
Clearing receiver’s memory 17
CUSTOMIZE menu 37
customizing 35
pre-programmed 30
resetting 36
selecting 30
D
Digital Cinema Sound 30
Direct tuning 24
Speakers
adjusting speaker level and balance 21
connection 15
placement 15
Dual Mono 38
Dubbing. See Recording
Supplied accessories 59
E
Editing. See Recording
T
EQUALIZER menu 37
Test tone 21
Tuning
automatically 23
directly 24
preset stations 24
I
Indexing. See Naming
L
Labeling. See Naming
LEVEL menu 35
N
Naming 39
P
Preset stations
how to 24
how to tune 25
61GB
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sony Corporation Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
|