PO Box 1200
305 Commerce Drive
Winfield, Alabama 35594
XB FREE FLOATING
FINISHING MOWER
Part No 999996
Download from Www.Somanuals.com. All Manuals Search And Download.
TO THE PURCHASER
This manual contains valuable information about your
new King Kutter Mower. It has been carefully prepared to
give you helpful suggestions for operating, adjusting, ser-
vicing and ordering repair parts.
Keep this manual in a convenient place for quick and
easy reference. Study it carefully. You have purchased a de-
pendable and sturdy mower, but only by proper care and op-
eration can you expect to receive the service and long life
designed and built into it.
Sometime in the future your mower may need new parts
to replace those that are worn or broken. If so, go to your
dealer and provide him with the model and part number.
Customer Information
Name ______________________________________________
Purchased From ______________________________________
Date Purchased ______________________________________
Model No. ___________________________________________
Serial No. ___________________________________________
3
Download from Www.Somanuals.com. All Manuals Search And Download.
It is the purchaser and/or operator’s responsibility to….
Read and understand the information contained in this
manual.
Operate, lubricate, assemble and maintain the
equipment in accordance with all instructions and
safety procedures in this manual.
Inspect the equipment and replace or repair any
parts that are damaged or worn which under contin-
ued operation would cause damage, wear to other
parts, or cause a safety hazard.
Return the equipment or parts to the authorized
King Kutter dealer, from where it was purchased, for
service or replacement of defective parts that are
covered by warranty. (The King Kutter Factory may
inspect equipment or parts before warranty claims
are honored.)
Payment of all costs incurred by the dealer for traveling
to or transporting the equipment for warranty inspection
and or claims.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
ITEM
PAGE
Safety.........................................................................6
Assembly Instructions ................................................8
Before Putting Into Service.......................................10
Safety Training .........................................................11
Operational Safety....................................................13
Transportation Safety ...............................................15
Attaching To Tractor..................................................16
Sizing PTO ...............................................................18
Operating Instructions ..............................................19
Maintenance.............................................................21
Belt Replacement.....................................................22
Maintenance Safety..................................................24
Safety Decal's And Locations...................................25
Replacement Parts...................................................32
PTO Shaft Parts .......................................................34
Spindle Unit Parts.....................................................35
Gearbox Parts ..........................................................36
PTO Shaft Cover Removal...................................…..38
Warranty ………………………………………………...41
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ AND FOLLOW THE INSTRUC-
TIONS IN THIS MANUAL AND ESPE-
CIALLY IN THE SAFETY SECTION.
FAILURE TO DO SO CAN RESULT IN
SERIOUS INJURY OR DEATH.
TAKE NOTE! THIS SAFETY ALERT
SYMBOL FOUND THROUGHOUT
THIS MANUAL IS USED TO CALL
YOUR ATTENTION TO INSTRUC-
TIONS INVOLVING YOUR PERSONAL
SAFETY AND THE SAFETY OF OTH-
ERS.
THIS SYMBOL MEANS
ATTENTION!
BECOME ALERT!
YOUR SAFTEY IS INVOLVED
SIGNAL WORDS:
The signal words DANGER, WARNING and CAUTION are used with the
safety messages in this manual and with each safety signs. They are defined as
follows:
DANGER: Indicates an immediate hazardous situation that, if not avoided,
could result in serious injury or death. This signal word is to be limited to the
most extreme situations typically for machine components that, for functional
purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous situation that, if not avoided,
could result in serious injury or death, and includes hazards that are exposed
when guards are removed. It may also be used to alert against unsafe practices.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practice.
If you have any questions not answered in this manual or require additional cop-
ies or the manual is damaged, please contact your dealer or King Kutter, Inc.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EQUIPMENT SAFETY GUIDELINES
Safety of the operator and by standards is one of the main concerns in designing and de-
veloping a mower. However, every year accidents occur which could have been avoided
by a few seconds of thought and a more careful approach to handling equipment. You, the
operator, can avoid many accidents by observing the following precautions and insist those
working with you, or for you, follow them.
In order to provide a better view, certain photographs or illustrations in this manual may
show an assembly with a safety shield removed. However, equipment should never be op-
erated in this condition. Keep all shields in place. If shield removal becomes necessary for
repairs, replace the shield prior to use.
Replace any safety sign that is not readable or is missing. Location of such safety signs is
indicated in this manual.
Never use alcoholic beverages or drugs that can hinder alertness or coordination while op-
erating this equipment. Consult your doctor about operating this machine while taking pre-
scription medications.
Under no circumstances should children under the age of 18 be allowed to work with this
equipment. Do not allow persons to operate or assemble this unit until they have read this
manual and have developed a thorough understanding of the safety precautions and of how it
works. Review the safety instructions with all users annually.
This equipment is dangerous to children and persons unfamiliar with its operation. The op-
erator should be a responsible, properly trained and physically able person familiar with
farm machinery and trained in this equipment’s operations. If the elderly are assisting with
farm work, their physical limitations need to be recognized and accommodated.
Use a tractor equipped with a Roll Over Protective System and seat belts. (ROPS)
Never exceed the limits of a piece of machinery. If its ability to do a job, or to do so safely,
is in question- DON’T TRY IT.
Do not modify the equipment in any way. Unauthorized modification could result in serious
injury or death and may impair the function and life of the equipment.
In addition to the design and the confirmation of this implement, including safety signs and
safety equipment, hazard control and accident prevention are dependent upon the aware
ness, concern, prudence, and proper training of personnel involved in the operation, trans
port, maintenance, and storage of the machine. Refer also to safety messages and opera-
tion instruction in each of the appropriate sections of the tractor and mower manuals. Pay
close attention to the safety signs affixed to the tractor and the finishing mower.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FINISHING MOWER ASSEMBLY INSTRUCTIONS
STEP 1
With finishing mower still in crate, lay flat on a level surface. Remove
the top & side sections of the crate, leaving the finishing mower rest-
ing on the bottom section. Set aside PTO shaft and tail wheel arm as-
semblies.
STEP 2
Insert tail wheel arms as shown in Figure A and tighten both the bolt & jam
nut.
STEP 3
Remove swivel links and lift pins that are wired on the lift arm “A” frame. Set
aside for step 5.
STEP 4
Remove the 4 bolts from the lift arm “A” frame.
Note: There are 2 different lengths of bolts.
STEP 5
Insert the swivel links in the center lift plate channel using the longer of the 2
bolts, on each side as shown in figure B.
STEP 6
Attach the other end of each swivel link to the outside lower hole on the lift
arm “A” frame using the shorter bolts as shown in Figure B.
STEP 7
Attach the Category 1 lift pins as shown in Figure B.
STEP 8
Tighten all nuts and bolts.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure A
Figure B
Figure C
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE PUTTING FINISHING MOWER INTO SERVICE
(IMPORTANT-INSTRUCTIONS PRIOR TO START UP)
SHIPPED WITH OIL IN GEARBOX
SHIPPED WITHOUT GREASE IN GREASE FITTINGS.
UNIT MUST BE SERVICED BEFORE USING.
•
•
Use Multi-Purpose Gear Oil (I.E. S.A.E. 80w/90 or S.A.E. 85w/140 Multi-
purpose gear oil) in Gearbox.
For all Grease Fittings use TYPE/grade II tube grease.
STEP 1
STEP 2
Place finishing mower so that the deck is secure and level.
Remove 1/2” Pipe Plug (Located at top of gearbox) and 1/8” Pipe Plug
(located at lower 1/3 of gearbox) if oil comes out lower hole replace lower
plug immediately and continue to Step 4. If no oil comes out continue to
Step 3.
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
STEP 8
Fill gearbox using multi-purpose gear oil through top 1/2” fill hole until gear
oil is level with lower 1/8" hole.
Replace both the 1/2” pipe plug (located at top of gear box) and
1/8"
pipe plug (located at lower 1/3 of gear box) and clean away any excess oil.
Fill spindle units (3) with grease until full. There are easy access holes in
top cover for greasing spindle units. (Figure C page 21)
Grease wheel axles (4), wheel forks (4), front roller axle (1), and PTO
shaft universal joints (2). (Figure C page 21)
Check air pressure in tires, maintain rated PSI listed on the tire at all
times.
Check all bolts, nuts and belt to insure they are tight and secure.
CAUTION:
DO NOT over fill gearbox. This could cause damage to oil seals and can cause per-
manent damage to the gearbox. This issue will not be covered under warranty.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY TRAINING
Safety is a primary concern in the design and manufacture of our product. Un-
fortunately, our efforts to provide safe equipment can be wiped out by a single
careless act of an operator or bystander.
In addition to the design and configuration of equipment, hazard control and ac-
cident prevention are dependent upon the awareness, concern, prudence and
proper training of personnel involved in the operation, transport, maintenance
and storage of this equipment.
It has been said, “ The best safety device is an informed, careful operator.” We
ask you to be that kind of operator. It is the operator’s responsibility to read and
understand all safety and operating instructions in the manual and to follow
them. Accidents can be avoided.
Working with unfamiliar equipment can lead to careless injuries. Read this man-
ual, and the manual for your tractor, before assembly or operating, to acquaint
yourself with the machines. If this machine is used by any person other than
you, or is loaned or rented, it is the finishing mower owner’s responsibility to
make certain that owner's manual be available to the operator prior to operating:
1- Reads and understands the operator’s manuals.
2- Is instructed in safe and proper use.
Know your controls and how to stop tractor, engine, and the mower quickly in an
emergency. Read this manual and the one provided with your tractor.
Train all new personnel and review instructions frequently with existing workers.
Be certain only a properly trained and physically able person will operate the
machinery. A person who has not read and understood all operating and safety
instructions is not qualified to operate the machine. An untrained operator ex
poses himself and bystanders to possible serious injury or death. If the elderly
are assisting with farm work, their physical limitations need to be recognized and
accommodated.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARTION
Never operate the tractor and mower until you have read and completely under-
stand this manual, the Tractor Operator’s Manual, and each of the safety mes-
sages found on the safety signs on the tractor and mower.
Personal protection equipment including hardhat, safety glasses, safety shoes, and gloves
are recommended during assembly, installation, operation, adjustment, maintenance, re-
pairing, removal, or moving the implement. Do not allow long hair, loose fitting clothing, or
jewelry to be around equipment.
PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING
LOSS! Tractors with or without mowers attached can often be noisy enough to cause per-
manent, partial hearing loss. We recommend that you wear hearing protection on a full-
time basis if the noise in the operator’s position exceeds 80 db. Noise over 80 db on a
long-term basis can cause severe hearing loss. Noise over 90 db adjacent to the operator
over a long-term basis may cause permanent, total hearing loss. NOTE: Hearing loss from
loud noise (from tractors, chain saws, radios, and other such sources close to the ear) is
cumulative over a lifetime without hope of natural recovery.
Operate the mower only with a tractor equipped with an approved Roll-Over-Protective
System (ROPS). Always wear your seat belt. Serious injury of even death could result
from falling off the tractor — particularly during a turnover when the operator could be
pinned under the ROPS or the tractor.
Clear area to be cut of stones, branches or other debris that might be thrown, causing in-
jury or damage.
Operate only in daylight or good artificial light.
Ensure mower is properly mounted, adjusted and in good operating condition.
Ensure that all safety shielding and safety signs are properly installed and in good condi-
tion.
STARTING AND STOPPING SAFETY
Check the tractor master shield over the PTO stub shaft. Make sure it is in good condition
and fastened securely to the tractor. Purchase a new shield if old shield is damaged or
missing.
All tractors that are not equipped with a “live” power takeoff (PTO) need to be equipped
with an over-running PTO clutch. These are available through most farm equipment
stores. NOTE: The addition of an over-running PTO clutch may change the length of the
PTO driveline required. Pay extra attention to the instructions on the PTO driveline Instal-
lation. Be sure that the driveline system guarding is adequate.
Mower operating power is supplied from tractor PTO. Refer to your tractor manual for PTO
engagement and disengagement instructions. Know how to stop tractor and mower
quickly in case of an emergency.
When engaging PTO, the engine RPM should always be at idle speed. Once engaged and
ready to start cutting, raise PTO speed to 540 RPM and maintain throughout cutting opera-
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL SAFETY
The use of this equipment is subject to certain hazards that cannot be pro-
tected against by the mechanical means or product design. All operators of
this equipment must read and understand this entire manual, paying particular
attention to safety and operating instructions, prior to using. If there is some-
thing in this manual you do not understand, ask your supervisor, or your
dealer, to explain it to you.
Most accidents occur because of neglect or carelessness. Keep all helpers
and bystanders at least several hundred feet from an operating finishing
mower. Only properly trained people should operate this machine.
When machine is operated in populated areas where thrown objects could in-
jure persons or property, operation must be stopped when anyone comes
within several hundred feet.
The majority of the accidents involve entanglement on the driveline, injury of
bystanders by the objects thrown by the rotating blades, and operators being
knocked off the tractor by low hanging limbs and then being run over by the
mower. Accidents are most likely to occur with machines that are loaned or
rented to someone who has not read the owner’s manual and is not familiar
with a finishing mower.
The finishing mower is designed for use only on tractors with 540-RPM power
take off.
Install and secure all guards and shields before starting or operating. The dis-
charge chute, bands, flaps, driveline guards and tractor, shields should be
used and maintained in good working condition. They should be inspected
carefully, at least daily, for missing or broken cable, chain links, shields, or
guards. (Worn items must be replaced at once to reduce possibility of injury)
Disengage power takeoff (PTO) and place transmission in neutral before at-
tempting to start engine.
Many varied objects, such as wire, cable, rope, or chains, can become entan-
gled in the operating parts of the mower. These items could then swing out
side the housing at greater velocities than the blades. Such a situation is ex-
tremely hazardous. Inspect the cutting area for such objects before mowing.
Remove any like objects from the site.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL SAFETY continued...
Never allow the cutting blade to contact such items. Cut material higher at
first, allowing finishing mower to clear hidden objects. Never assume an area
is clear. Always Check!
Always stop the tractor, disengage PTO, set brake, shut off the tractor engine,
remove the ignition key, lower implement to the ground and allow cutter
blades to come to a complete stop before dismounting tractor. Never leave
equipment unattended with the tractor running.
Never place hands or feet under mower with tractor engine running or before
you are sure all motion has stopped. Stay clear of all moving parts.
Do not reach or place any part of your body under equipment until it is
blocked securely.
Do not allow riders on the finishing mower or tractor at anytime. There is no
safe place for any riders.
Do not operate unless all personnel, livestock, and pets are several hundred
feet away to prevent injury by thrown objects. Never direct discharge chute
toward anyone.
Never operate tractor and finishing mower under trees with low hanging limbs.
Operators can be knocked off the tractor and then run over by the rotating
blades.
The rotating parts of this machine have been designed and tested for rugged
use. However, they could fail upon impact with heavy, solid objects such as
steel guardrails and concrete abutment. Such impact could cause the broken
objects to be thrown outward at very high velocities. To reduce the possibility
of property damage, serious injury, or even death, never allow the cutting
blades to contact such obstacles.
-
Stop mower and tractor immediately upon striking an obstruction. Turn en-
gine off, remove key, inspect and repair any damage before resuming opera-
tion.
Stay alert for uneven terrain, holes, rocks, and roots and other hidden haz-
ards. Keep away from drop-offs and hazards that could cause roll over. Use
extreme care and maintain minimum ground speed when transporting or oper
ating on hillsides, over rough ground and when operating close to ditches or
fences. Be careful and slow down when turning sharp corners and changing
direction on slopes. Do not start or stop suddenly on slopes. Avoid operation
on steep slopes. In extremely uneven terrain, rear wheels weights, front trac-
tor weight, and/or tire ballast should be used to improve stability.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONAL SAFETY continued...
Pass finishing mower diagonally through sharp dips and avoid sharp drops to
prevent “hanging up” tractor and finishing mower. Practice will improve your
skills in maneuvering on rough terrain. Always cut down slopes, never across
the face. Always check tractor manual for proper use on slopes.
When using a unit, a minimum 20% of tractor and equipment weight must be
on tractor front wheels. Without this weight, tractor could tip over, causing
personal injury or death. The weight may be attained with a front- end loader,
front wheel weights, ballast in the tires or front tractor weights. When attain-
ing a minimum 20% of tractor and equipment weight on the front wheels, you
must not exceed the ROPS weight certification. Weigh the tractor and equip-
ment. Do not guess or estimate!
TRANSPORT SAFETY
Comply with state and local laws governing highway safety and movement of
farm machinery on public roads.
The use of flashing amber lights is acceptable in most localities. However,
some localities prohibit their use. Local laws should be checked for all lighting
and marking requirements.
At all times, when driving the tractor and equipment on the road or highway
under 20 mph (32 kph) use flashing amber warning lights and a slow moving
vehicle (SMV) identification emblem. Do not exceed 20 mph (32 kph). Re-
duce speed on rough roads and surfaces.
Plan your route to avoid heavy traffic.
Always install transport locks, pins or brackets before transporting.
Do not drink and drive.
Be a safe and courteous driver. Always yield to oncoming traffic in all situa-
tions, including narrow bridges, intersections, etc. Watch for traffic when op-
erating near or crossing roadways.
Turn curves or go up or down hills only at a low speed and at a gradual steer-
ing angle. Make certain that a least 20% of the tractor’s weight is on the front
wheels to maintain safe steerage. Slow down on rough or uneven surface.
Always check tractor manual for proper use on slopes.
Use extreme care and maintain minimum ground and when operating close to
ditches or fences. Be careful when turning sharp corners.
Never allow riders on either tractor or mower.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING TO TRACTOR
WARNING
Never stand between
tractor and finishing mower
while backing up tractor
to the hitch.
STEP 1
Attach to tractor's category 1 three point hitch as described in
the Tractor's Operator’s Manual.
WARNING
Failure to install retaining clip on gearbox input shaft would allow driveline to
swing freely if bolt is sheared causing possible injury or death.
STEP 2
Determine if the PTO shaft needs to be shortened.
NOTE:
Due to the many variations in the tractor hitch points and distances between
equipment gearbox input shaft and tractor PTO out put shafts, some combina-
tions may require PTO shafts to be shortened as described by the following
steps.
STEP 3
Raise and lower finishing mower in order to locate the shortest distance be-
tween equipment gearbox input shaft and tractor PTO output shaft. With the
finishing mower in the shortest distance position shut down the tractor and
SECURELY BLOCK FINISHING MOWER IN POSITION.
STEP 4
Pull apart PTO shaft and attach outer section to tractor PTO output shaft.
NOTE: Be sure to pull on PTO shaft section to ensure yoke has locked into
place.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING TO TRACTOR continued....
STEP 5
Place and hold inner PTO shaft section next to outer section and check if PTO
shaft is too long. Each section should end approximately 3 inches short of
reaching u-joint shield on the opposite section. If the shaft is too long meas-
ure 3 inches back from each u-joint shield and mark the other shaft section.
Be sure to do this for both PTO shaft halves. NOTE: Do not cut PTO shaft
sections at this time.
STEP 6
Raise finishing mower and remove blocking. Raise and lower finishing mower
in order to locate the longest distance between equipment input shaft and the
tractor PTO output shaft. With the finishing mower in the longest distance po-
sition shut down the tractor and SECURELY BLOCK THE FINISHING
MOWER IN POSITION.
STEP 7
As in step 5 hold PTO shaft sections together and check for a minimum of 6
inches of overlap. If PTO shaft has been marked for cutting the overlap is the
distance measured between the two marks. If the PTO shaft has less than a
6 inch overlap, DO NOT USE. Contact your authorized King Kutter Dealer.
NOTE
If the PTO shaft length is too long go to SIZING PTO SHAFT (pg. 18)
STEP 8
Apply any multi-purpose grease to the outside of the male (inner) PTO shaft
section. Assemble PTO shaft and install on finishing mower and tractor.
WARNING - Failure to install retaining clip on gearbox input shaft would al-
low driveline to swing freely if bolt is sheared causing possible injury
or death.
STEP 9
Pull on tractor side of PTO shaft yoke to be sure it has locked in place. Make
certain PTO shaft shielding is in place and good working condition.
STEP 10
The PTO shaft shield is a non-rotating design and must be secured prior to
equipment use. Using the chain on each yoke shield attach to a fixed object
on the tractor and equipment ends that will not allow the PTO shaft shield to
rotate during operation.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SIZING PTO SHAFT
STEP 1
Cutting the PTO shaft to length.
NOTE: Be sure to cut equal lengths
of each PTO shaft section. Clamp
end of PTO shaft in a vice and cut off
shield where marked. (Figure 1-A &
1-B)
Figure 1-A
STEP 2
Using cut section of the shield as a
guide cut shaft off the same amount.
(Figure 2)
STEP 3
Repeat steps 1 and 2 for other PTO
shaft section.
Figure 1-B
STEP 4
Use a file to deburr PTO shafts.
Clean up all chips, burrs and filings
from both ends of the PTO shaft.
Note: If you shear the bolt that attaches
the PTO shaft to the gearbox re-
place with a grade 2 bolt only. Re-
placement with another grade of
bolt will void your warranty and may
cause terminal damage to the PTO
shaft, gearbox, or tractor.
Figure 2
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
This mower was designed to CUT LAWN GRASS ONLY. Use of your finish-
ing mower to cut any material other than lawn grass may damage the mower
and void your warranty.
CUTTING HEIGHT ADJUSTMENT
To prevent blades from striking the ground your finishing mower
should be set to the highest position that will give desired grass
height. By setting your mower up this way you reduce blade wear and
stress on the mower. Mowing at regular intervals will yield far better
results than periodic mowing. (i.e. weekly vs. by-weekly mowing.)
STEP 1
Raise finishing mower off the ground with the tractor and SECURELY
BLOCK IN POSITION.
STEP 2
Remove pin from top of wheel fork assembly. Lower wheel fork
assembly from tail wheel arm.
STEP 3
Arrange spacers until desired cutting height is achieved. Cutting heights
range from approximately 2.0-6.0 inches in height.
STEP4
Reinstall wheel fork assembly into tail wheel arm and install keeper pin.
STEP 5
Repeat adjustment process on remaining wheel fork assemblies. NOTE:
Make sure all are adjusted to the same height for an even cut.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
FINISHING MOWER OPERATION
STEP 1
Before each use perform the maintenance described in maintenance section (pg#
21)
STEP2
Read, understand, and follow the information on safety training, preparation, start-
ing and stopping safety, operational safety, transport safety warning sections of this
manual (pages 11 thru 16)
STEP 3
With tractor running, lower finishing mower to ground so that the swivel links are
parallel to the ground. This allows the free-floating hitch system to follow the con-
tour of the ground, thus mowing evenly on uneven terrain.
STEP 4
With the tractor at idle RPM, engage PTO and slowly advance throttle to 540 PTO
RPM. NOTE: Finishing mower designed to run at 540 PTO RPM only.
STEP 5
Select a low gear for the tractor and begin to mow. Tractor ground
speed is to be controlled by gear selection only and not engine speed.
Tractor ground speed should allow finishing mower to maintain 540 PTO
RPM and thus maximum blade tip speed.
NOTE: Do not allow the tractor engine or finishing mower to bog down or stall.
This causes undue wear and tear on the mower and tractor. If this continues to
happen reduce ground speed and raise cutting height of finishing mower. Never at-
tempt to clean out a plugged discharge chute until the tractor has been shut down
and the mower blades have completely stopped.
STEP 6
After each use clean all debris from the top and bottom of the finishing
mower. Replace any missing or illegible safety decals. Inspect for any
damaged or worn parts and replace before next use. Store finishing mower
in a dry environment.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
1). Periodically check and maintain proper gear oil level.
2). Every 8 hours, grease spindles (3), roller axle (1), wheel forks (4), wheel axles
(4), PTO shaft universal joints (2), and PTO telescoping surface.
NOTE: Use only a grade Type II tube grease.
3). Keep tires inflated to rated PSI (listed on tire) at all times.
4). Before each use check to make sure all safety features are installed and
working properly.
5). Keep blades sharp and balanced at all times. When replacing blades, replace
all 3 blades and blade bolts at the same time.
NOTE: Blade bolts are left hand thread!
6). Periodically check all nuts, bolts, and belt to insure they are tight and secure.
Figure C
(grease points at arrows)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TO REPLACE BELT:
STEP 1
STEP 2
STEP 3
Remove PTO shaft.
Remove top cover.
Loosen nut on adjustment pulley to allow for movement.
(see Figure “D”)
STEP 4
STEP 5
Loosen nut on right side of “L” bracket. (see Figure “D”)
Loosen belt by moving adjustment pulley in opposite direction
you would to tighten belt.
STEP 6
STEP 7
Remove belt from all pulleys and idlers, leaving it on the main pul
ley. (See Figure E)
Loosen nuts (4) retaining the gearbox to the gearbox plate.
Note: the top of the nuts should be flush with the end of the bolts.
STEP 8
STEP 9
Remove bolts (4) holding the gearbox plate to the finishing mower deck.
Remove the gearbox and gearbox plate assembly from the finish
ing mower. Note: the belt should be removed with the assembly.
STEP 10
Turn gearbox and plate assembly over and allow to rest on the
gearbox. This will allow a space to develop between the main pul
ley and the gearbox plate flange. The belt can be removed through
this space.
STEP 11
STEP 12
Install new belt.
Re-assemble by reversing steps 1 through 10.
TO ADJUST BELT:
STEP 1
STEP 2
STEP 3
Remove top cover.
Loosennutonadjustmentpulleytoallowformovement. (seeFigureD)
Tighten nut on right side of “L” bracket until belt is sufficiently
tight. (See Figure D)
STEP 4
STEP 5
Re-tighten nut on adjustment pulley.
Install top cover.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure D
Figure E
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE SAFETY
Good maintenance is your responsibility. Poor maintenance is an invitation to trou-
ble.
Follow good shop practices.
Keep service area clean and dry
Be sure electrical outlets and tools are properly grounded
Use adequate light for the job at hand.
Make sure there is plenty ventilation. Never operate the engine of the towing vehi-
cle in a closed building. The exhaust fumes may cause asphyxiation.
Before working on this machine, disengage the PTO, shut off the engine, set the
bakes, and remove the ignition keys.
Be certain all moving parts on attachments have come to a complete stop before
attempting to perform maintenance.
Never work under equipment unless it is blocked securely.
Always use personal protection devices such as eye, hand and hearing protectors,
when performing any service or maintenance.
Frequently check mower blades. They should be sharp, free of nicks and cracks
and securely fastened. NOTE: Blade bolts are left hand thread!
Periodically tighten all bolts, nuts, and screws and check that all cotter pins are
properly installed to ensure unit is in safe condition.
When completing a maintenance or service function, make sure all safety shields
and devices are installed before placing unit in service.
After servicing, be sure all tools, parts and service equipment are removed from
mower.
Do not allow debris, grease or oil to build up on any deck or platform.
Where replacement parts are necessary for periodic maintenance and servicing,
genuine factory replacement parts must be used to restore your equipment to origi-
nal specifications.
The manufacturer will not be responsible for injuries or damages caused by use of
unapproved parts and/or accessories.
A fire extinguisher and the first aid kit should be kept readily accessible while per-
forming maintenance on this equipment.
STORAGE SAFETY
Following operation, or when unhooking the mower, stop the tractor, set
the brakes, disengage the PTO, shut off the engine and remove the igni-
tion keys.
Store the unit in an area away from human activity.
Do not park equipment where it can be exposed to direct contact to livestock for
long periods of time. Damage and livestock injury could result.
Make sure all parked machines are on a hard, level surface and engage all safety
devices.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SIGN LOCATIONS
The types of safety signs and locations on the equipment are shown in the illustra-
tion below. Good safety requires that you familiarize yourself with the various safety
signs, the type of warning and the area, or particular function related to that area,
that requires your SAFTY AWARENESS
REMEMBER: If safety signs have been damaged, removed, become illegible or
parts have been replaced without signs, new safety signs must be applied. New
safety signs are available from your authorized dealer, distributor or factory.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
1
28
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
30
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
8
31
Download from Www.Somanuals.com. All Manuals Search And Download.
9
10
32
Download from Www.Somanuals.com. All Manuals Search And Download.
11
MODEL NO.
DESCRIPTION
SN# XXXXXXXXXX
12
33
Download from Www.Somanuals.com. All Manuals Search And Download.
XB FINISHING MOWER
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Ref.
No.
Part Name
Part Number
5-1/2’
1
2
Top Cover
Gearbox Plate
124684
403029
502303
164090
403682
1671081
184000
165114
502011
502010
500001
502012
3
Spindle Unit -Spindle
Idler Pulley -Single
Belt Adjustment Assembly
V -Belt*
4
5
6
7
Gear Box
8
Main Pulley -Single
Bolt 3/4” x 4” w/ nut
Swivel Link Set
9
10
11
12
CAT. 1 Lift Pin (Pkg. 2)
Lift Arm Spacer w/ Nut & Bolt
13
14
15
Lift Arm Assembly
Center Roller w/ Axle
Roller Axle
403662
502110
403670
16
17
18
19
20
21
22
23
24
25
26
27
28
Height Adjuster Set
Tail Wheel Arm
502120
403700
403665
403681
403023
502125
502015
502690
502316
502313
147022
502310
502297
Side Panel RH
Side Panel LH w/ Chute
Wheel Fork
Axle Bolt 3/4” x 5” w/ Nut
Tire & Rim w/ Axle & Nut
Chain Assembly
Blade Set w/ Bolts
Spindle Pulley - Single
22” PTO Shaft
LH Blade Bolt Set w/ Washers
Plastic Knob
1
* B-108
33
Download from Www.Somanuals.com. All Manuals Search And Download.
22" PTO 147022
Ref.
No.
Part Name
147022
1
2
Roll Pin Kit
500131
151045
151040
151050
151035
151090
151091
170015
170110
124310
124311
Male Tube End Yoke
Implement End Yoke
Female Tube End Yoke
Tractor End Yoke
3
4
5
6
Inner Tube 14 Series
Outer Tube 14 Series
Cross Kit # 4
7
8
9
Quick Disconnect Pin
Safety Shield BYPY
Safety Shield Eurocardan
10
10
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Spindle Unit
Ref.
No.
Part Name
502303
Bearing Kit - (2) Ball Bearings (6205),
(2) Seals (TCM25x52x7TC), (4) Snap Rings
1 & 2
555009
502313
Spindle Pulley /w Nut & Key
3
4
Blade Bolt Set (3) /w Washer
502310
35
Download from Www.Somanuals.com. All Manuals Search And Download.
40 HP GEARBOX
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Ref.
No.
Part Name
Gearbox
184000
1
2
Snap Ring
Input Seal (NAK 35 x 54 x 10)
Front Cap
106138
156010
129015
124130
131031
131030
155005
185007
186010
155010
129010
185005
-
3
4
Front Cap Gasket
Snap Ring
5
6
Snap Ring
7
Bearing (Hoover 208)
Input Gear
8
9
Input Shaft
10
11
12
13
14
15
16
17
18
19
20
Bearing (NSK 6207)
Housing
Output Shaft
Spacer
Output Seal (NAK 40 x 54 x 7)
Bottom Cap Gasket
Bottom Cap
156005
124131
129005
501110
131035
131040
-
1’ Castle Nut /w Washer & Cotter Pin
1/2” Pipe Plug
1/8” Pipe Plug
3/8” x 1” Bolt & Lockwasher
37
Download from Www.Somanuals.com. All Manuals Search And Download.
PTO SHAFTS COVER REMOVAL
BONDIOLI- (BYPY)
1). There are 3 white tabs around the cover as shown in (A in FIG. 1). Take a
screwdriver and press against the tabs one at a time with downward angular
pressure toward the end of shaft marked (B in FIG. 2). As you are pressing
tab grasp cover at point marked (B in FIG. 2) and apply pressure against
cover in the direction of arrow, do this for each tab. (Sometimes the other tabs
may relock, if they do you must repeat unlock procedure.) You will feel it click
when the tab releases, after all 3 tabs are released you can slide the cover
down the shaft in direction of (C in FIG. 2).
2) To put cover back into place slide cover back toward end until all the tabs
relock. (You may have to tap lightly with screwdriver or hammer handle).
NOTE: Cover may be longer on some models but, they will come off the
same as above.
EUROCARDAN SERIES 4
1)
First you must locate the black tab (D in FIG. 3) put flat screwdriver in slot in
end of tab and turn until the flat side is pointing towards center of shaft. Once
you do this take the thin flat screwdriver and put into slot labeled (E in FIG. 3)
pry tab all the way out as shown in (FIG. 3)
2). There are 3 white tabs around the cover as shown in (G in FIG. 4). You must
line up cover slots and tabs (as shown in FIG. 4, F & G) Take a screwdriver
and press against the tabs one at a time with downward angular pressure to-
ward the end of shaft. As you are pressing tab grasp cover and apply pres-
sure against cover in the direction of arrow, (H in FIG-3) do this for each tab.
(Sometimes the other tabs may relock, if they do you must repeat unlock pro-
cedure.) You will feel it click when the tab releases, after all 3 tabs are re-
leased you can slide the cover down the shaft in
PTO
SHAFTS COVER REMOVAL direction of (H in FIG. 3).
3)
To put cover back into place slide cover back toward end (be sure tabs and
slots line up) until all the tabs relock. (You may have to tap lightly with screw-
driver or hammer handle). Once they have relocked replace black tab that
was removed with flat side toward shaft center then turn flat side up to lock in
place.
LA MAGDALENA
1)
There are 3 black tabs around the cover (K in FIG. 5). Take a screwdriver and
press against the tabs one at a time with downward angular pressure toward
the end of shaft marked (J in FIG. 5). As you are pressing tab grasp cover at
point marked (J in FIG. 5) and apply pressure against cover in the direction of
arrow, do this for each tab.
2)
To replace slide cover back toward end and line up black tabs with the holes
38
Download from Www.Somanuals.com. All Manuals Search And Download.
BONDIOLI COVER REMOVAL
FIGURE- 1
FIGURE– 2
EUROCARDAN SERIES 4 COVER REMOVAL
FIGURE– 3
FIGURE– 4
LA MAGDALENA COVER REMOVAL
FIGURE– 5
39
Download from Www.Somanuals.com. All Manuals Search And Download.
PTO SHAFTS COVER REMOVAL
EUROCARDAN SERIES 5
1). There are 2 black tabs around the cover as shown in (B in FIG. 1). Take a flat
screwdriver and pry under the tabs one at a time at point (B in FIG. 2) lifting
tab over on top of (e-shaped lock). After both tabs are released you can
slide the locking ring down the shaft in direction of (C in FIG. 3). Then you
will see a metal e-ring (E in FIG. 4) at point (D in FIG. 4) you must pry under
ring and remove it, (it will just slide down shaft unless you take PTO apart)
then apply pressure against cover (A in FIG. 1) in the direction of arrow and
slide cover down shaft.
2) To put cover back into place slide cover back toward end, making sure cover
and locking mechanism (F in FIG. 4) line up. Replace metal e-ring, slide the
locking ring back into place, be sure the tabs lock securely over locks.
NOTE: Cover may be longer on some models but, they will come off the
same as above.
FIGURE- 1
FIGURE– 2
FIGURE– 3
FIGURE– 4
40
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Limited Warranty.
King Kutter, Inc. (“King Kutter”), P.O. Box 1200, Winfield, Alabama 35594, warrants to the original retail
purchaser (“Purchaser”) that the product that is the subject of this sale is free from defects in material and
workmanship at the time of sale.
Under this warranty, King Kutter will repair the defective product free of charge to the Purchaser, with ei-
ther new or used and reconditioned replacement parts. All warranty service will be performed at service
centers designated by King Kutter. If King Kutter is unable to repair the product to conform to the warranty
after a reasonable number of attempts, King Kutter will provide, at its option, one of the following: (a) a re-
placement for the product or, (b) a full refund of the purchase price. Repair, replacement, or refunds are
the Purchaser’s EXCLUSIVE remedies against King Kutter under this limited warranty. King Kutter will not
be liable for any special, incidental or consequential damages based upon breach or warranty, breach of
contract, negligence, strict tort liability, or any other legal theory. Such damages include, but are not lim-
ited to, loss of profits, loss of savings or revenue, loss of use of the product or any associated equipment,
cost of capital, cost of any substitute equipment, facilities or services, down time, the claims of third parties
including customers, and injury to property. These limitations also apply, to the extent allowed by law, to
personal injury.
The purchaser must notify the Seller in writing of any defect in material or workmanship within one (1) year
following the date of purchase. If the equipment is used for commercial purposes, the Purchaser must no-
tify the Seller in writing of any defect in material or workmanship within ninety (90) days following the date
of purchase. In no event will King Kutter be liable under this warranty unless written notice is received by
the Seller within one (1) year from the date of original retail sale.
2. Warranty of Title.
King Kutter warrants that it transfers a good title to the product free of any encumbrances, and free of the
rightful claim of any third party for infringement of patent or copyright.
3. What is Not Covered by This Limited Warranty.
King Kutter will not be responsible for damage to or failure in the product which results from accident, mis-
use, abuse, neglect, installation of attachments not provided by King Kutter, modifications to the product,
or damage caused by use of the product for purposes other than those for which it was designed.
4. No Other Warranties.
Unless modified in writing and signed by both parties, this agreement is understood to be the complete and
exclusive agreement and warranty between King Kutter and Purchaser, superseding all prior agreements,
oral and written, and all other communication between King Kutter and Purchaser related to the subject
matter of this agreement.
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, IN-
CLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IM-
PLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. No employee of King Kutter nor any-
one else is authorized to make any warranty or representation in addition to or different from those made in
this agreement.
5. Allocation of Risk.
This agreement allocates the risk of product failure between King Kutter and the Purchaser. This Alloca-
tion is recognized by both parties as reflected in the price of the goods. The Purchaser acknowledges that
he or she has read this agreement, understands it, and is bound by its terms.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
FIVE YEAR LIMITED GEARBOX WARRANTY
King Kutter warrants to the original purchaser of any new King Kutter product equipped with a
Gearbox, a Gearbox only limited Five (5) year warranty, for non-commercial, non-state, non-
municipalities, and non-rental use and for 90 days for commercial non-rental use or a 30-day war-
ranty is offered for rental use.
Under no circumstances will this Warranty apply in the event that the product, in good faith opin-
ion of King Kutter, has been subjected to improper operation, improper maintenance, misuse, fire
or an accident. This Warranty does not apply in the event that the product has been materially
modified or repaired by someone not authorized prior to repair by King Kutter. This Warranty does
not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover
repairs made with parts other than those obtainable through King Kutter.
This Warranty is extended solely to the original purchaser of the product. Should the original pur-
chaser sell or otherwise transfer this product to a third party, this Warranty does not transfer to the
third party purchaser in any way. There are no third party beneficiaries of this Warranty.
King Kutter’s obligation under this Warranty is limited to, at King Kutter’s option, the repair or re-
placement of the product if King Kutter in its sole discretion, deems it to be defective or in non-
compliance with this Warranty. The product must be returned to King Kutter with proof of
purchase within thirty (30) days after such defect or noncompliance is discovered or
should have been discovered, routed through the dealer and distributor from whom the
purchase was made, transportation charges prepaid. THERE ARE NO OTHER REMEDIES
UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND
EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE DESCRIPTION ON THE
FACE OF THIS WARRANTY. KING KUTTER MAKES NO OTHER WARRANTY, EXPRESS OR
IMPLIED, AND KING KUTTER SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF
MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE.
King Kutter shall not be liable for any incidental or consequential losses, damages or ex-
penses, arising directly or indirectly from the product, whether such claim is based upon
breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory.
Without limiting the generality of the foregoing, King Kutter specifically disclaims any damages
relating to lost profits, business revenues or goodwill, loss of crops, loss of delay in harvesting;
any expense or loss incurred for labor, supplies, substitute machinery or rental; or any other type
of damage to property or economic loss.
Any and ALL repairs must be pre-approved by King Kutter prior to any repairs being made and
subject to all conditions, restrictions, and purchaser obligations as stated within this warranty.
Five (5) Year Limited Gearbox Warranty is a variable warranty based on purchase date, within
one year from original purchase date, to the original owned. Warranty would include parts and
labor based on all restrictions and limits as stated above. King Kutter reserves the right to limit la-
bor in hours and hourly charges. All repairs must be pre-approved prior to work being done. Years
2 through 5 are parts only warranty. NO LABOR WILL BE PAID.
.........Continued on next
42
Download from Www.Somanuals.com. All Manuals Search And Download.
King Kutter reserves the right to ask and inspect all parts prior to a warranty decision being made. Inciden-
tal expenses such as lubricants and transportation to and from the dealer are not covered by warranty.
It is the original purchaser’s burden and obligation to maintain proof of purchase, a copy of which must ac-
company any and all warranty claims.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, in-
cluding without limitation, King Kutter, its authorized dealers, distributors, and service centers, is author-
ized to alter, modify or enlarge this Warranty.
This Warranty is effective on any King Kutter product purchased January 1, 2008 and after and is subject to
change without notice.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Ingersoll Rand Lawn Mower FA10 User Manual
Invacare Mobility Aid 6300 5F User Manual
JBL Speaker System SP6CSII User Manual
JVC Stereo Receiver RX 8010RBK User Manual
Kenwood Blender BL760 User Manual
Kenwood Car Speaker KFC HQ710 User Manual
Kettler High Chair 01491 000 User Manual
KitchenAid Ice Maker 2313684A User Manual
KitchenAid Indoor Furnishings KKFV01LPCR User Manual
Kodak Camera Accessories CIS 267E User Manual