Dishwasher Installation Manual
Model DWL3025
Quality • Innovation • Style
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
PAGE
Before Using Your Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
WHAT DO I NEED TO HAVE TO INSTALL THE DISHWASHER? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Tools, parts & materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Cabinet Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
WHAT DO I NEED TO DO BEFORE I INSTALL THE DISHWASHER? . . . . . . . . . . . . . . . . . . . . . . . . 10-20
Prepare cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-14
Prepare dishwasher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-20
HOW DO I INSTALL THE DISHWASHER?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-25
Connect dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-23
Secure dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Check operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE USING THE DISHWASHER
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS
Doing so will:
make installation easier.
help you in the future if you have questions.
help if you have an electrical inspection.
This is the safety alert symbol.
This symbol alerts you to potential hazards that may seriously
injure you and others.
All safety messages follow the safety alert symbol and either the
word “DANGER” or “WARNING”.
DANGER
YOU CAN BE SERIOUSLY INJURED IF YOU DO NOT FOLLOW INSTRUCTIONS
IMMEDIATELY.
WARNING
YOU CAN BE SERIOUSLY INJURED IF YOU DO NOT FOLLOW INSTRUCTIONS.
All safety messages will tell you what the potential hazard is, how to reduce
the chance of injury and what can happen if the instructions are not followed.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
YOU NEED TO
• Carefully open dishwasher door while someone grasps the rear of the dishwasher. Remove
shipping materials and lower rack. Close dishwasher door. Latch the dishwasher door shut.
• Install this dishwasher as specified in these instructions.
• Have everything you need (tools, materials, parts) to properly install the dishwasher.
IMPORTANT
• Observe all governing codes and ordinances.
• Note to installer – Be sure to leave these instructions for the consumer’s and
inspector’s use.
• Note to consumer – Keep these instructions with your owner’s manual for future
reference.
• Skill level – Installation of this dishwasher requires basic mechanical, electrical, and
plumbing skills.
Proper installation is the responsability of the installer. Product failure
due to improper installation is not covered under warranty.
See warranty information.
• Completion time – 1 to 3 hours. New installations require more time than replacement
installations.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS AND MATERIALS NEEDED
ALL INSTALLATIONS
A Pliers
B. Phillips screwdriver
5
C. /8” open end wrench
D. Measuring tape or ruler
E. 10” adjustable wrench that opens to 11/8” (2.9 cm)
F. Flat-blade screwdriver
G. Gloves
H. Utility knife
I. 2 twist-on wire connetors which are the proper size to connect your house hold wiring to
16-gauge wiring in dishwasher
J. Small level
K. Safety glasses
L. 90° elbow with 3/8” (0.9 cm) N.P.T external threads on one end. (The other end must fit your
water supply line.)
M.Flashlight
N. Teflon® tape or pipe joint compound
O. Shallow pan
P. Shim stock (if instlled with built-up floor)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
In addition for new installations
Q. Electric drill
R. ½”, ¾”and 1½” hole saw bits
S. Small tubing cutter
T. Wire stripper
U. 1½”-2” screw-type clamp if connecting to waste-tee
V. Copper tubing (3/8” recommended) or flexible strainless steel braided fill line
W. Clamp connector or conduit connector to fit a 7/8” (2.2 cm) diametre hole
® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
Parts supplied
A. 2 drain hose clamps
1-large
1-small
B. 2 No. ST4.2 X 18 Phillips head screws
C. Drain hose
Make sure all these parts are included.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
REQUIREMENTS
Cabinet Requirements
Do not run water drain lines or electrical wiring where they can interfere with or contact
dishwasher motor or legs.
The location where the dishwasher will be installed must provide clearance between motor
and flooring.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher against freezing.
Damage from freezing is not covered by the warranty.
Check location where dishwasher will be installed. The location must provide:
- Easy access to water, electricity and drain.
- Convenient loading. Corner locations require a 2” (5.1 cm) minimum clearance between the
side of the dishwasher door and wall or cabinet.
- Square opening for proper operation and appearance.
- Cabinet front perpendicular to floor.
- Level floor. If floor at front of opening is not level with floor at rear of opening, shims may
be needed to level dishwasher.
NOTE: Shims must be securely attached to floor to
prevent their movement when dishwasher is being
operated.
If dishwasher will be left unused for a period of time or
in a location where it may be subject to freezing, have
it winterized by authorized service personnel.Make sure
pipes, wires and drain hose are within the shaded area.
See page 9 for dimensions.
HELPFUL TIP:
If the floor in the dishwasher opening in uneven (example: tile flooring only part way
into opening) you will needed to take special care in measuring dimensions and in
leveling dishwasher.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
It is the customer’s responsibility:
To assure that the electrical installation is adequate and in conformance will all national and
local codes and ordinances.
You must have:
- 120-volt, 60Hz, AC-only, 15- or 20-amp., fused electrical supply, and connected to an
individual, properly grounded branch circuit.
- Wiring must be 2-wire with ground and rated for 176°F (75°C).
We recommend:
- a time-delay fuse or circuit breaker.
- a separate circuit.
If direct wiring dishwasher:
- Use flexible, armored or non-metallic sheathed, copper wire
with grounding wire that meets the wiring requirements for
your home and local codes and ordinances.
- Use strain relief method provided with house wiring
junction box or install a cUL-listed/CSA-certified clamp
connector to the house wiring junction box. If using
conduit, use a cUL-listed/CSA-certified conduit connector.
If connecting dishwasher with a power supply cord:
- Use a cUL-listed, 16-gauge, three-conductor power supply
cord that meets all local codes and ordinaces. Maximum
length of the power supply cord is 6 feet (1.8 m).
- A clamp connector to fit a 7/8” (2.2 cm) diameter hole is
required to secure power supply cord to dishwasher
terminal box.
- Power supply cord must plug into a mating three-prong,
grounded outlet,located in the cabinet next to the
dishwasher opening. Outlet must meet all local codes
and ordinances.
WARNING
Electrical Shock Hazard
The improper connection of the equipment grounding conductor can
result in a risk of electric shock. Check with a qualified electrician if you
are in doubt that the appliance is properly grounded.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER
You must have:
- A hot water line with 20-120 psi (138-862 kPa) water pressure.
- 120°F (49°C) water at dishwasher.
3
- /8” (0.9 cm) O.D. tubing with compression fitting or flexible stainless steel braided fill line
(½”/1.3 cm) minimum plastic tubing is optional but not recommended).
- A 90° elbow with 3/8” (0.9 cm) N.P.T. external pipe threads on one end.
Do not solder within 6” (15.2 cm) from water inlet valve.
DRAIN
You must:
- Use the new drain hose supplied with your dishwasher. If this is not suitable, use a new
drain hose with a maximum length of 12 feet(3.7 m) that meets all current AHAM/IAPMO
test standards, is resistant to heat and detergent, and fits the drain connector on your
dishwasher.
above the subfloor or floor.
- Have a high drain loop 30 inches (76.2 cm)
- Connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20 inches
(50.8 cm) minimum above the floor.
- Use an air gap if the drain hose is connected to house
plumbing lower than 20 inches (50.8 cm) above
subfloor or floor.
- Use ½” (1.3 cm) minimum I.D. drain line fittings.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CABINET DIMENSIONS
24” (61 cm)**
All surfaces must be free
from intrusions
24”
(61 cm)
min.
34” (86.4 cm) min.*
3¼”
3¼”
(8.3 cm)
(8.3 cm)
5½”
(14 cm)
2”
(5.1 cm)
2”
(5.1 cm)
6” ***
(15.2 cm)
6” ***
(15.2 cm)
2”
(5.1 cm)
9”
10”
(25.4 cm)
(22.9 cm)
3¼”
(8.3 cm)
2¾”
(7 cm)
3¼”
(8.3 cm)
2¾”
(7 cm)
Cut openings in shaded area of cabinet walls or floor as specified in chart:
OPENING FOR:
Water Line
DIAMETER
½” (1.3 cm)
1½” (3.8 cm)
¾” (1.9 cm)
1½” (3.8 cm)
Drain Line
Direct Wire
Power Supply Cord
*
Measured from the lowest point on the underside of countertop.
May be reduced to 337/8” (86 cm) by removing wheels from dishwasher.
** Minimum, measured from narrowest point of opening.
*** Maybe increased to 67/8” (17.5 cm) if height of opening is 34½” (87.6 cm) at lowest point.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit breaker
box before installing dishwasher.
Failure to do so can result in death or electrical shock.
Do not use an extension cord or adapter plug with this appliance.
A. PREPARE CABINET
1. Disconnect the power supply. Turn water off. Put on gloves and safety glasses.
2. If you are replacing a dishwasher:
- Check that the water line “A” reaches to the back left of
opening where the water connection will be made.
- Check that the direct line “B” reaches to the back left of
opening where the electrical connection will be made.
If the water line and the direct wire reach into the opening far
6” (15.2 cm)
enough, go to step 10, page 12.
If you are installing a new dishwasher , complete all of the following steps:
Electrical
Follow all national and local codes and ordinaces for completing electrical supply to
cabinet.
If you are:
Use Steps:
3, 4 and 5
3a and 4a
Direct Wiring
Using a Power Supply cord
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HELPFUL TIP:
Wiring the dishwasher will be easier if you route wire into the cabinet opening from
the left side.
3. Direct wire method:
Cut a ¾” (1.9 cm) hole “C” in righthand cabinet side, rear
or floor. Optional locations are shown.
Wood Cabinet: Sand hole until smooth.
4. Run wire into house wiring junction box. Use strain relief method provided with junction
box. If no strain relief is provided, install a cUL-listed/CSA-certified clamp connector for
flexible-type wire. If installing conduit, attach a cUL-listed/CSA-certified conduit
connector to junction box.
5. Run other end of wire through cabinet hole. Cable must
extend to the left front of cabinet opening. Go to step 6.
6” (15.2 cm)
3a. Power supply cord method:
Cut a 1½” (3.8 cm) hole “D” in right-hand cabinet rear or
side. Optional locations are shown.
Wood cabinet: Sand hole until smooth.
4a. Install a mating, three-proung, grounding-type wall
receptacle “E” in the cabinet next to the dishwasher
opening. Go to step 6.
Water Line
HELPFUL TIP:
Routing the water line through the left side of cabinet opening will make water
connection easier.
6. Cut a ½” (1.3 cm) minimum hole “F” in left-hand cabinet
side,rear or floor. Optional locations are shown. (The hole
“F” is about 13/5” higher than hole “C” or hole “D”)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Measure overall length of copper tubing “G” required.
Attach copper tubing to water line with manual shutoff
valve. Carefully feed copper tubing through hole in
cabinet (copper tubing will bend and kink easily) until it
is far enough into the cabinet opening to connect it to
dishwasher inlet on the front left of dishwasher.
8. Turn shutoff valve “H” to “ON” position. Flush water
into a bucket to get rid of particles that may clog the
inlet valve.
9. Turn shutoff valve to “OFF” position.
Drain Hose
10. Cut a 1½” (3.8 cm) diameter hole in cabinet wall or floor
on the side of the opening closest to the sink.
11. Connect drain hose to waste tee or waste disposer following one method.
If you have:
And:
Go to Step:
11a.
An Air Gap
No Air Gap*
An Air Gap
No Air Gap*
A Waste Disposer
11c.
11b.
No Waste Disposer
11d.
* An air gap is recommended
11a. Waste disposer + air gap
1. Remove the disposer knockout plug.Cut end of drain
hose “I” if needed (do not cut ribbed section).
2. Attach drain hose to air gap “J” with large spring-type
clamp “K”. If the drain hose was cut, use a 1½” to 2”
(3.8 to 5 cm) screw-type clamp*.
3. Use a rubber hose connector* “L” with spring or
screwtype clamps* “M” to connect air gap to disposer
inlet “N”. This connection “N” MUST be before drain trap
“O” and at least 20” (50.8 cm) above the floor where
dishwasher will be installed. Go to step 12.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
11b. No waste disposer + air gap
1. Cut end of drain hose “I” if needed (do not cut ribbed
section).
2. Attach drain hose to air gap “J” with large springtype
clamp. If the drain hose was cut, use a 1½” to 2” (3.8 to
5 cm) screw-type clamp*.
3. Use a rubber hose connector* “L” with spring or
screwtype clamps* “M” to connect air gap to waste
tee “P”.
This connection “P” MUST be before drain trap “O” and
above the floor at 154/5” (40 cm) to 392/5” (100 cm),at least
20” (50.8 cm) above the floor where dishwasher will be
installed. Go to step 12.
11c. Waste disposer, no air gap
See note 3
(30” loop)
1. Remove the disposer knockout plug.
Do not cut end of drain hose.
2. Attach drain hose “I” to disposer inlet “N” with large
spring type clamp “K”.
This connecting “N” MUST be before drain trap “O” and
at least 20” (50.8 cm) above the floor where dishwasher
will be installed.
3. The drain hose must be looped up and securely fastened
to the underside of the counter before going to the drain. Hose
loop must be a minimum of 30” (76.8cm) above floor.
Go to step 12.
11d. No waste disposer + no air gap
See note 3
(30” loop)
1. Cut end of drain hose “I” (do not cut ribbed section).
2. Attach drain hose to waste tee “P” with 1½” to 2”
(3.8 to 5 cm) screw-type clamp* “M”.
This connecting
MUST be before drain trap “O” and
“P”
at least 20” (50.8 cm) above the floor where dishwasher
will be installed.
3. The drain hose must be looped up and securely fastened
to the underside of the counter before going to the drain. Hose
loop must be a minimum of 30” (76.8cm) above floor.
Go to step 12.
* Parts available from local plumbing supply stores.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HELPFUL TIP:
To reduce the vibration of the hose, keep the hose away from the floor and the edge of
the hole where it passes through the cabinet.
12. Insert drain hose “I” into hole cut in cabinet to the
back center of opening where drain connection
will be made.
B. PREPARE DISHWASHER
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
WARNING
Excessive Weight Hazard
Use two people to move and install dishwasher.
Failure to do so can result in back or other injury.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Grasp sides of dishwasher door and put dishwasher on its back.
2. Remove two screws “A” attaching access panel “B”
and lower panel “C” to dishwasher using a ¼” hex
socket,nut driver or Phillips screwdriver. Remove
panels and set panels aside on a protective surface.
Check that grounding clip “D” is attached to the
lower panel.
3. Apply pipe joint compound “E” to 90° elbow fitting
“F” and connect fitting to water inlet valve “G”.
Tighten elbow until snug, and be sure that it faces to
the rear.
4. Remove terminal box cover “H”. Pull appliance wires
“I” through hole in terminal box. Do not untie the
knot in the wires.
If you are direct wiring: install a cUL-
listed/CSAcertified clamp connector “J” to the
terminal box. If using conduit use a cUL-listed/CSA
certified conduit connector.
If you are installing a power supply cord kit, do so
now and follow kit instructions.
HELPFUL TIP:
Put cardboard under dishwasher until it is installed. The cardboard will help protect
floor covering during installation.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Measure height of cabinet opening from underside
of countertop to floor where dishwasher will be
installed “K” (you need the lowest point). Check
chart for that height opening. Put wheels “L” in the
required position. Turn both front leveler legs to the
same height.
Min. Cutout
Height
Wheel Position
(See Illustration)
Number of Turns
on Front Leg
34” (86.4 cm)
34¼” (87 cm)
34½” (87.6 cm)
1
2
3
10
5
Front Leg
0
If the minimum cutout height is less than 34” (86.4 cm), the adjustable legs can be removed
for additional clearance. This will allow the dishwasher to fit into a 334/5” (85.9 cm) high
cutout, but the dishwasher will be more difficult to move into position. If the wheels are
removed, protect the floor when moving the dishwasher.
HELPFUL TIP:
Built-up floors.
Countertop
Measure height of opening from underside of
countertop to built-up floor. If the height is at least
33¾” (84.5 cm), the dishwasher will fit into the opening
without modification to the countertop or flooring.
Put wheels “L” in position 1 and turn the front leveler
legs up all the way.
33¾”
(85.7 cm)
min.
Shim
Built-up Floor
Add shims as needed in the area shown to bring
dishwasher up to proper height.
Note: Shims must be securely attached to floor to
prevent their movement when the dishwasher is
operated.
2”
(5.1 cm)
Shim
Shim
2¾”
(7 cm)
6”
(15.2 cm)
2¾”
(7 cm)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Stand dishwasher upright.
7. The dishwasher must be secured to the cabinet.
There are two brackets on top of the dishwasher
that usually can be attached to the countertop. If
this is not possible,the brackets “M” may be moved
to the sides of the dishwasher.
If you are going to attach the dishwasher to the
countertop,skip to step 13.
If you are going the attach the dishwasher to the
sides of the cabinet, follow steps 8 through 12.
8. To remove the brackets from the top,flatten tab “N”
at back of brackets with pliers,and pull the brackets
out of the slots “O”.
9. Break off the end of the bracket along the scored
line “P”.
10. Open dishwasher door and place towel “Q” over
pump assembly and spray arm of dishwasher.This
will prevent screws from falling into pump area
when securing dishwasher to countertop.
11. Open dishwasher door and push the plastic buttons
“R” out of the side of the tub.
NOTE: Save the buttons to cover the holes after
dishwasher is installed.
12. Push bracket into slot “S” on the side of
dishwasher,and bend tab in towards the side of the
dishwasher so that it keeps the bracket in place.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Check the door spring tension. With another person
holding the dishwasher to prevent it from tipping, open
and close the door a few times. If the door opens by
itself, adjust the door spring tension.
To adjust the door spring tension, unhook the spring
“T” from the rear leg of dishwasher. With a 5/16” nut
driver or hex socket, remove the screw ”U” from the
tensioner “V”. The screw can be put into one of three
holes “1”, “2”, “3”, in front leg of dishwasher. The
dishwasher is shipped with the screw in the back hole.
If the door opened by itself, move the tensioner to hole
“2” or “3” and replace screw. Re-attach door spring to
rear leg. Tensioners on both sides of dishwasher should
be secured at same holes.
14. Grasp the dishwasher door at the edges of the door
panel “W”. Tilt dishwasher backwards on wheels “X”.
Move dishwasher close to cabinet opening. DO NOT
PUSH ON FRONT OF PANEL OR ON CONSOLE - THEY
MAY DENT.
15. If dishwasher has a power supply cord, insert power
supply cord into hole cut into cabinet.
16. Check that water line is on the left side of opening and
drain hose is near the center of the hole in the cabinet.
If using direct wire, check that it is on the right side of
opening.
17. Carefully move dishwasher completely into cabinet
opening. Do not kink or pinch copper tubing, drain
hose, power supply cord or direct wire between
dishwasher and cabinet.
Center dishwasher in opening.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HELPFUL TIP:
Built-up floors.
Tilt dishwasher backward to move into opening.
Once in position, support front of dishwasher by lowering
or shimming front feet.
18. Remove cardboard from under dishwasher.
HELPFUL TIP:
It is okay if dishwasher fits tightly into cabinet opening. Do not remove insulation
blanket - it reduces the sound level.
19. Align front of dishwasher door panel “Y” with cabinet doors
“Z”. You may need to adjust alignment to look good with
your cabinets.
HELPFUL TIP:
Prop up one side of frame to hold dishwasher up off floor
when adjusting front legs.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Check that leveling legs “AA” are firmly against the floor.
Close and latch the door, and place level against the
front panel “BB”. Check that dishwasher is plumb.
Adjust leveling leg or add shims under rear wheel until
dishwasher is level.
NOTE: Shims must be securely attached to floor to
prevent their movement when the dishwasher is
operated.Repeat for other side of dishwasher.
Place level against top front opening of tub “CC”. Check
that dishwasher is level from side to side. If dishwasher
is not level, adjust front legs up or down until
dishwasher is level.
C. CONNECT DISHWASHER
Electrical Connection
Check electrical requirements (see page 7).
You need to:
- Have the correct electrical supply and recommended
grounding method.
- Check that power supply is disconnected.
If you are:
Use Steps:
Direct Wiring
1-4
1a
Using a Power Supply cord
Water
Drain
Electrical
20
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Direct wire method:
WARNING
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in terminal
box. Do not use an extension cord. Failure to do so can result
in death, fire, or electrical shock.
Install strain relief and route direct wire so that it does
not touch dishwasher motor or lower part of dishwasher
tub. Pull direct wire “A” through hole in terminal box.
HELPFUL TIP:
• Select the proper size twist-on connectors to connect
your household wiring to 16-gauge dishwasher wiring.
• Insert wire ends into twist-n connector. Do not pretwist
bare wire.
• Twist connector.
• Gently tug on wires to be sure both are secured.
2. Connect the wire “B” as follows using twist-on
connectors “C” sized to connect direct wire to 16-
gauge dishwasher wire:
From bare ground wire “D” into a U-shaped hook.
Wrap ground wire hook clockwise around ground
connector “E” and under the washer “F”. Securely
tighten ground connector “E” and under the washer
“F”.
Securely tighten ground connector “E”. Do not untie
knot in the wires.
Power Supply Wire:
White
Terminal Box Wire:
White
Black
Black
Ground Wire
Ground Wire
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Tighten clamp connector or conduit connector screws “G”.
4. Reinstall terminal box cover “H” with wires inside terminal
box. Go to step 5. The cover must be outside the box on the
right side. Make sure no wires are pinched by cover.
Do not leave the box without the cover.
1a. Power Supply Cord Method:
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
Check that power supply cord does not touch dishwasher
motor or lower part of dishwasher tub. Go to step 5.
Water Connection
HELPFUL TIP:
Compression Fittings:
1 Slide nut “I” onto copper tubing “J” about 1” (2.5 cm).
2.Slide ferrule "K" onto the tubing. Do not position
ferrule on the end of the tubing.
3. Put the tubing into the elbow “L” as far as it will go.
4. Slide the nut and ferrule forward and start the nut
onto the elbow threads “M”. Be careful when handling
and positioning the copper tubing. It bends and kinks easily.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
5. To prevent vibration during operation, route the
water supply line so that it does not touch the
dishwasher base, frame or motor. Make sure the
water line stays within the shaded area shown on
page 7 when the dishwasher is installed in the
cabinet. With copper tubing “J” pushed into
compression fitting as far as it will go, use an
adjustable wrench and tighten compression fitting
nut “I” to elbow “L” on water inlet valve.
6. Place Paper towel under elbow. Turn on water supply and check for leaks.
Drain Connection
7. To help minimize vibration noise, route drain hose
to avoid contact with motor, door springs, water
line, cabinet, flooring or the edge of the hole where
it passes through the cabinet.
Do not remove drain loop “N” from side of
dishwasher.
8. Place the smaller drain hose clamp “N” onto the
small end of the drain hose “O”. Remove the plug
from the connector “P”.
9. Push the drain hose into the connector “P” up to
the rib “O” on the drain hose.
10. Use pliers to open clamp “N” and slide clamp onto
connector “P” between ribs “O” on connector.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
D. SECURE DISHWASHER
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
1. Open dishwasher door and place towel “A” over pump
assembly and spray arm of dishwasher. This will prevent
screws from falling into pump area when securing
dishwasher to countertop.
2. Check that dishwasher is still level and centered in the
opening.
3. Secure dishwasher to countertop with two, No. ST4.2 x 18
Phillips-head screws “B”. The dishwasher MUST be secured
to keep it from tipping when door is opened. Do Not drop
screws into bottom of dishwasher.
4. Open door about 3 inches (7.6 cm) and check that space
between inner door and tub is equal on both sides. If
spacing is not equal,loosen bracket screws and shift tub.
Tighten bracket screws. If securing to sides of cabinet,
replace the plastic buttons “C”.
Check that top of door does not contact screws, brackets,
or countertop. If it does,dishwasher must be lowered and re-leveled.
Remove paper or towel from dishwasher.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
E. CHECK OPERATION
1. Read the Owner’s Manual that came with your dishwasher.
2. Check that all parts have been installed and no steps were skipped. Check that you have
all the tools you used.
3. At fuse box or circuit breaker, turn on electrical power supply to dishwasher. Start
dishwasher and allow it to complete the shortest wash cycle. After the first two minutes,
unlatch door, wait five seconds, then open door. Check to see that there is water in the
bottom of the dishwasher and that there are no water leaks.
4. Check that grounding clip “A” is attached to the lower
panel. Place the lower panel “B” behind the access panel
“C”. Some models have insulation “D” on the access
panel which must fall behind the insulation “E” on the
lower panel. Hold the two panels together and place
them against dishwasher leg. Reinstall the screws
through the holes in the access panel and the slots in the
lower panel. Install right side screw first. Check that the
lower edge of the lower panel contacts the floor. Tighten
the screws.
If Dishwasher Does Not Operate:
– Has the circuit breaker tripped or the house fuse blown?
- Is the door closed tightly and latched?
- Has the cycle been set correctly to start the dishwasher?
- Is the water turned on?
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Side view
Model
DWL3025
25” (63,5 cm)
¾”(1.9cm)
insulation
may be
compress
-ed.
337/8 “ (86 cm)
minimum with
wheels removed
21”(53.3cm)
52
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
Do Not Return This Product To the Store
If you have a problem with this product,please contact the
“Haier Customer Satisfaction Center” at 1-877-337-3639.
DATED PROOF OF PURCHASE MODEL # AND SERIAL #
REQUIRED FOR WARRANTY SERVICE
Haier America
New York, NY 10018
Made in China
DWL3025DBWW/DBBB/SBSS
Issued:June 09
Printed in China
Part No. 0120504139B
Download from Www.Somanuals.com. All Manuals Search And Download.
|