Sidewall Propeller Fans
Belt and Direct Drive
Exhaust, Supply and Reversible
December
2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Comparison
Direct Drive Fan Selection
Three propeller and drive frame combinations are available. Models SE1 and SS1 are designed for smaller
size applications where lower volumes and static pressures are found. Models SE2, SS2, SCE3 and SCS3
are designed and constructed for applications with higher volumes and static pressures.
Construction
Levels
Size Range
diameter
Models
Performance
Fabricated
aluminum
propeller riveted
to the hub
Up to 6,700 cfm
(11,383) and up to
5/8 in. wg (156)
SE1
SS1
8 to 24 in.
(203 to 610)
1
Fully welded and
gusseted steel
blade and hub
design
Up to 45,000 cfm
(76,455) and up to
1 in. wg (249)
Level 1
Sizes 12 to 24
Level 1
Sizes 8 to 12
SE2
SS2
16 to 54 in.
(406 to 1372)
2
3
SCE3
SCS3
SCR3
Up to 45,000 cfm
(76,455) and up to
1 in. wg (249)
Cast aluminum
air foil blades
24 to 54 in.
(610 to 1372)
All measurements given in in. (mm), cfm (m3/hr) or in. wg (Pa).
Level 3
Level 2
Belt Drive Fan Selection Propeller Types
Three propeller drive frame construction levels and two blade designs are available. The application
requirements for sound and static pressure determine propeller type. Propellers are available in fabricated
steel, fabricated aluminum or cast aluminum.
Construction
Levels
Size Range
diameter
Models
Performance
Galvanized steel
blades riveted to
the hub
Up to 30,000 cfm
(50,970) and up to
5/8 in. wg (156)
SBE-1
SBS-1
20 to 54 in.
(508 to 1372)
1
2
Dual thickness
galvanized steel
blades riveted to SBS-2
the hub
Up to 53,000 cfm
(90,048) and up to
3/4 in. wg (19)
SBE-2
20 to 60 in.
(508 to 1524)
Level 1
Level 2
Fabricated, fully
welded and
Up to 87,000 cfm
(149,513) and up
to 1 in. wg (249)
SBE-3
24 to 72 in.
(610 to 1829)
3
3
gusseted steel
SBS-3
blade and hub
design
Cast aluminum
air foil blades
and hub design
SBCE
SBCS
SBCR
Up to 87,000 cfm
(149,513) and up
to 1 in. wg (249)
24 to 72 in.
(610 to 1829)
Level 3
Fabricated
Level 3
Cast Aluminum
All measurements given in in. (mm), cfm (m3/hr) or in. wg (Pa).
Blade Designs
L Propeller: Swept, steeply pitched blade design. These propellers typically run
at lower RPMs and generate low sound levels making them the best selection for
sound critical applications or applications that require the best combination of
both air and sound performance. Typically used when the static pressure is 0.5 in.
wg (13 mm) or less.
H Propeller: Straight, moderately pitched blade. It is designed for applications
where static pressures are above 0.5 in. wg (13 mm). These propellers typically run
at higher RPMs and generate slightly higher sound levels than the “L” propellers.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Options Overview
Mounting Option
Description
Page
l
wal
Standard Wall
Mounting
Fan can be mounted
directly to a wall.
5
wall
Standard
Horizontal
Mounting
Fan can be horizontally
mounted to move air up
or down.
6
The wall collar is an
easy way to mount the
sidewall propeller fan
and its accessories.
7
Wall Collar
The wall housing is
the easiest and most
flexible way to mount the
sidewall propeller fan
and all its accessories.
8-9
Wall Housing
The filtered supply wall
housing is flexible and
easy way for installations
where filtering is
Filtered
Supply Wall
Housing
10
required.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Wall Mounting
Mounting Fan Directly to Wall
The split drawing below illustrates the typical ways of mounting fans directly to the wall when a wall housing
or collar is not used.
For exhaust fans, there is a minimum dimension (M) which must be maintained between the propeller and
damper or guard to achieve optimum performance (failure to meet this minimum dimension will result in loss
of fan performance, increased noise and shortened fan and damper life). There is also a minimum required wall
opening dimension (W.O.) to allow the venturi to fit into the wall opening.
See the chart at right for the minimum “M” and wall opening dimensions.
Fan
Size
Wall
Opening
M
spacer
This installation may
require a spacer (by
others) between the
fan and wall to achieve
the minimum “M”
dimension.
l
8
10
12
14
16
18
20
24
30
36
42
48
54
60
72
6 (152)
6 (152)
7 (178)
8 (203)
9 (229)
10 (254)
12 (305)
13 (330)
13 (330)
14 (356)
15 (381)
16 (406)
17 (432)
19 (483)
19 (483)
101⁄2 (267)
121⁄2 (318)
141⁄2 (368)
161⁄2 (419)
181⁄2 (470)
201⁄2 (521)
221⁄2 (572)
261⁄2 (673)
321⁄2 (826)
381⁄2 (978)
441⁄2 (1130)
501⁄2 (1283)
561⁄2 (1435)
621⁄2 (1588)
741⁄2 (1892)
guard
wal
Fans can be mounted
directly to a wall
M
only if the wall is of
sufficient thickness to
meet the minimum “M”
dimension as shown
here.
damper
All dimensions given in inches (mm).
wall
Motor Side Guard
Protective guards of welded steel wire completely enclose the motor and drive side
of the fan. Guards are coated with Permatector, a thermal setting polyester urethane.
Other paint finishes are also available. Sizes 20 and larger only.
OSHA Motor Side Guard
Protective guards of expanded metal screen in structural steel frames are available to
completely enclose the motor and drive side of the fan.
Weatherhood
Weatherhoods shield wall openings and dampers from rain and snow. Weatherhoods
are shipped unassembled in kit form for field assembly. Construction is of galvanized
steel with wire mesh birdscreen. Mounting flanges have prepunched mounting holes.
45° turn down is for exhaust and 90° turn down is for exhaust and supply. Options
include aluminum construction, insect screen and painted finish.
Damper Guard
Damper guards meet the OSHA requirements completely enclose the damper or
wall openings on the discharge side of the fan. They are constructed of expanded
galvanized steel screen in galvanized steel frames. Mounting flanges have prepunched
mounting holes. Options include aluminum construction and painted finish.
Dampers
Used alone or in conjunction with the wall housing or wall collar, a complete line of
dampers is available for exhaust or supply configurations.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Horizontal Mounting Option
Horizontally mounted fans are available for applications requiring vertical airflow. Typical applications
include mounting fans in ductwork or plenums as transfer fans or suspending them from the ceiling in a
wall housing for use as recirculation fans. Both belt and direct drive fans can be horizontally mounted.
Motors can be mounted on top or on bottom with airflow up or down. Specify configuration best suited for
access and service.
Horizontally mounted fans are put under different stresses than fans mounted in a wall. Construction
modifications are required depending on motor location (top or bottom) and whether the fan is belt or direct
drive.
These modifications may include the following:
A - Grooved shaft with snap rings
(belt drive fans)
B - Motor pulley retaining hardware
(belt drive fans with motor on bottom)
C - Reinforcing angles on fan panel - not shown
(all fans with motor on bottom)
D - Propeller retaining hardware
(direct drive fans with motor on top)
A
Exhaust Fan
Supply Fan
Motor on Top
Motor on Top
Air Blowing Upward
Air Blowing Downward
Airflow
Airflow
Guarding is strongly
recommended
D - Retaining Hardware
Hangers by others
Motor on Bottom
Air Blowing Upward
Motor on Bottom
Air Blowing Downward
Airflow
Airflow
(Shown as suspended
installation with fan
(Shown as suspended
installation with fan
mounted in wall housing.)
mounted in wall housing.)
Wall
Housing
Exhaust Fan
Supply Fan
Guard or Diffuser
B
NOTE: Protective guarding is also required below the fan for safety. When guarding is not ordered with the fan, it must
be supplied by the installer. When specifying a fan for horizontal mounting, the motor location (top or bottom)
and airflow (upward or downward) are required information.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Collar Mounting Option
Wall collars offer an alternate method for mounting sidewall propeller fans and
the optional accessories shown here. Standard construction is of galvanized steel
(painted steel is optional) with heavy gauge mounting flanges and pre-punched
mounting holes.
F
W. O.
D
A
C
E
G*
B
Motor Side
Guard
Wall Collar
Damper Guard
Weatherhood
Size
Damper
A
B**
W.O.
C
D
E
F
Width
G*
8
10
12
14
16
18
20
24
30
127⁄8 (327)
147⁄8 (378)
177⁄8 (454)
197⁄8 (505)
217⁄8 (556)
237⁄8 (606)
257⁄8 (657)
317⁄8 (810)
377⁄8 (962)
161⁄8 (410)
161⁄8 (410)
161⁄8 (410)
183⁄8 (467)
183⁄8 (467)
183⁄8 (467)
183⁄8 (467)
183⁄8 (467)
141⁄4 (362)
161⁄4 (413)
191⁄4 (489)
211⁄4 (540)
231⁄4 (591)
251⁄4 (641)
271⁄4 (692)
333⁄4 (857)
51⁄2 (140)
61⁄2 (165)
53⁄8 (137)
63⁄8 (162)
63⁄4 (171)
6 (152)
101⁄4 (260)
121⁄4 (311)
141⁄4 (362)
161⁄4 (413)
181⁄4 (464)
201⁄4 (514)
221⁄4 (565)
261⁄4 (667)
321⁄4 (819)
381⁄4 (972)
131⁄4 (337)
147⁄8 (378)
163⁄8 (416)
171⁄2 (445)
193⁄8 (492)
22 (559)
243⁄4 (629)
267⁄8 (683)
291⁄8 (740)
111⁄4 (286)
133⁄8 (340)
155⁄8 (397)
175⁄8 (448)
195⁄8 (498)
215⁄8 (549)
235⁄8 (600)
303⁄8 (772)
361⁄2 (927)
101⁄2 (267)
121⁄2 (318)
141⁄2 (368)
161⁄2 (419)
181⁄2 (470)
201⁄2 (521)
221⁄2 (572)
291⁄8 (740)
351⁄8 (892)
85⁄8 (219)
9 (229)
10 (254)
12 (305)
14 (356)
16 (406)
18 (457)
20 (508)
22 (559)
26 (660)
32 (813)
38 (965)
44 (1118)
50 (1270)
56 (1422)
62 (1575)
74 (1880)
11 (279)
11 (279)
11 (279)
11(279)
16 (406)
18 (457)
21 (533)
22 (559)
24 (610)
27 (686)
32 (813)
32 (813)
32 (813)
61⁄2 (165)
63⁄8 (162)
61⁄2 (165)
63⁄4 (171)
183⁄8 (467) 393⁄4 (1010)
183⁄4 (476) 453⁄4 (1162)
183⁄4 (476) 513⁄4 (1314)
187⁄8 (479) 573⁄4 (1467)
201⁄8 (512) 633⁄4 (1619)
21 (533) 693⁄4 (1772)
22 (559) 833⁄4 (2127)
36 437⁄8 (1114)
42 497⁄8 (1127)
48 557⁄8 (1419)
54 617⁄8 (1572)
60 677⁄8 (1724)
72 817⁄8 (2080)
33 (838) 421⁄2 (1080) 411⁄8 (1045)
353⁄4 (908) 481⁄2 (1232) 471⁄8 (1197)
10 (254) 441⁄4 (1124)
9 (229) 501⁄4 (1276) 403⁄8 (1026) 545⁄8 (1387) 531⁄4 (1353)
71⁄2 (191) 561⁄4 (1429) 443⁄4 (1137) 607⁄8 (1546) 591⁄2 (1511)
71⁄4 (184) 621⁄4 (1581) 483⁄8 (1229)
67 (1702) 655⁄8 (1667)
71⁄2 (191) 741⁄4 (1886) 531⁄4 (1353) 791⁄2 (2019) 781⁄8 (1984)
*Dimensions are for exhaust fan guard. See CAPS for supply fan and for optional OSHA motor side guard dimensions. **All sizes except 20 and 72 are 2 in (51 mm)
larger if a VCD damper is used. For complete dimensional information refer to submittal. All dimensions given in inches (mm).
Motor Side Guard — Protective guards of welded steel wire
completely enclose the motor and drive side of the fan. Guards
are coated with Permatector, a thermal setting polyester
urethane. Other paint finishes are also available. Sizes 20 and
larger only.
OSHA Motor Side Guard — Protective
guards of expanded metal screen in structural
steel frames are available to completely
enclose the motor and drive side of the fan.
Dampers — Used alone or in conjunction with the wall housing
or wall collar, a complete line of dampers is available for exhaust
or supply configurations.
Note: Wall collar, fan, damper and guards ship
completely factory assembled except when
ordered as a kit.. Weatherhood ships loose.
Damper Guard — Damper guards meet the OSHA requirements completely
enclose the damper or wall openings on the discharge side of the fan. They are
constructed of expanded galvanized steel screen in galvanized steel frames.
Mounting flanges have prepunched mounting holes. Options include aluminum construction and painted
finish.
Weatherhood — Weatherhoods shield wall openings and dampers from rain and snow. Weatherhoods
are shipped unassembled in kit form for field assembly. Construction is of galvanized steel with wire mesh
birdscreen. Mounting flanges have prepunched mounting holes. 45° turn down is for exhaust and 90° turn
down is for exhaust and supply. Options include aluminum construction, insect screen and painted finish.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Housing Mounting Option
Wall housings are the safest, most efficient and sturdy platform for mounting
sidewall propeller fans and their optional accessories. Wall housings allow
for a wide range of mounting arrangements to meet specific applications. It
is constructed of galvanized steel (painted steel optional) with heavy gauge
mounting flanges and prepunched
mounting holes. Protective guards
of welded steel wire completely
protect the drive side of the wall
housing. Guards are coated with
A
W. O.
F
D
Permatector, a thermal setting
polyester urethane. Other paint
finishes are also available.
Wall housing guards that meet
the OSHA requirements are also
available.
C
E
B*
Wall Housing
B*
Damper Guard
Weatherhood
F
Material
Gauge (ga)
Thickness
Size
Damper
A
W.O.
C
D
E
Width
8
10
12
14
16
18
20
24
30
131⁄4 (337)
151⁄4 (387)
181⁄4 (464)
201⁄4 (514)
221⁄4 (565)
241⁄4 (616)
261⁄4 (667)
321⁄4 (819)
381⁄4 (972)
19 (483)
19 (483)
23 (584)
26 (660)
27 (686)
28 (711)
32 (813)
37 (940)
38 (965) 393⁄4 (1010)
39 (991) 453⁄4 (1162)
44 (1118) 513⁄4 (1314)
44 (1118) 573⁄4 (1467)
52 (1321) 633⁄4 (1619)
54 (1372) 693⁄4 (1172)
60 (1524) 843⁄4 (2153)
141⁄4 (362)
161⁄4 (413)
191⁄4 (489)
211⁄4 (540)
231⁄4 (591)
251⁄4 (641)
271⁄4 (692)
333⁄4 (857)
51⁄2 (140)
61⁄2 (165)
53⁄8 (137)
63⁄8 (162)
63⁄4 (171)
6 (152)
61⁄2 (165)
63⁄8 (162)
61⁄2 (165)
63⁄4 (171)
101⁄4 (260)
121⁄4 (311)
141⁄4 (362)
161⁄4 (413)
181⁄4 (464)
201⁄4 (514)
221⁄4 (565)
261⁄4 (667)
321⁄4 (819)
381⁄4 (972)
131⁄4 (337)
147⁄8 (378)
163⁄8 (416)
171⁄2 (445)
193⁄8 (492)
22 (559)
243⁄4 (629)
267⁄8 (683)
291⁄8 (740)
111⁄4 (286)
133⁄8 (340)
155⁄8 (397)
175⁄8 (448)
195⁄8 (498)
215⁄8 (549)
235⁄8 (600)
303⁄8 (772)
361⁄2 (927)
101⁄2 (267)
121⁄2 (318)
141⁄2 (368)
161⁄2 (419)
181⁄2 (470)
201⁄2 (521)
221⁄2 (572)
291⁄8 (740)
351⁄8 (892)
10 (254)
12 (305)
14 (356)
16 (406)
18 (457)
20 (508)
22 (559)
26 (660)
32 (813)
38 (965)
44 (1118)
50 (1270)
56 (1422)
62 (1575)
74 (1880)
20
20
20
20
20
20
18
18
18
18
18
18
16
16
12
36 441⁄4 (1124)
42 503⁄8 (1280)
48 563⁄8 (1432)
54 623⁄8 (1584)
60 683⁄8 (1737)
72 831⁄8 (2111)
33 (838) 421⁄2 (1080) 411⁄8 (1045)
353⁄4 (908) 481⁄2 (1232) 471⁄8 (1197)
10 (254) 441⁄4 (1124)
9 (229) 501⁄4 (1276) 403⁄8 (1026) 545⁄8 (1387) 531⁄4 (1353)
71⁄2 (191) 561⁄4 (1429) 443⁄4 (1137) 607⁄8 (1546) 591⁄2 (1511)
71⁄4 (184) 621⁄4 (1581) 483⁄8 (1229)
67 (1702) 655⁄8 (1667)
71⁄2 (191) 741⁄4 (1886) 531⁄4 (1353) 791⁄2 (2019) 781⁄8 (1984)
* B dimension will increase by 6 in (152 mm) when a heavy duty motorized backdraft damper is specified. For complete dimensional information refer to submittal.
All dimensions given in inches (mm).
Dampers — Used alone or in conjunction with the wall housing or
wall collar, a complete line of dampers is available for exhaust or
supply configurations.
Damper Guard — Damper guards meet the OSHA requirements
completely enclose the damper or wall openings on the discharge
side of the fan. They are constructed of expanded galvanized
steel screen in galvanized steel frames. Mounting flanges
have prepunched mounting holes. Options include aluminum
construction and painted finish.
Weatherhood — Weatherhoods shield wall openings and
dampers from rain and snow. Weatherhoods are shipped
unassembled in kit form for field assembly. Construction is
Note: Wall housing, fan, damper and guards ship
completely factory assembled except when
of galvanized steel with wire mesh birdscreen. Mounting flanges have
ordered as a kit. Weatherhood ships loose.
prepunched mounting holes. 45° turn down is for exhaust and 90° turn down
is for exhaust and supply. Options include aluminum construction, insect screen and painted finish.
Diffusers - Wall Housing Mounted - Manual Operator
Diffusers are constructed with heavy
gauge galvanized steel frames, blades and
prepunched mounting flanges. They are
Closure Angles
An extra set of
mounting flanges
is available for
Mounting
Angles
Closure Angles
INTERIOR
EXTERIOR
designed to mount to the interior end of the wall
housing when used in the supply configuration.
Manual quadrants set the angle of the blades to
deflect air in 1, 2 or 4 directions.
field installation to
close off the interior
wall opening for a
finished appearance.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Housing Mounting Arrangements
The wall housing is designed to reduce installation time and provide maximum installation flexibility.
Attached accessories such as backdraft dampers, guards and weatherhoods may mount to either end. As a
result a wide variety of configurations are available to accommodate the needs of the system designer.
The following information will help determine the correct arrangement required. When ordering specify
arrangement by the drawing number 1A, 2A, 1B or 2B as shown in the diagrams below.
NOTE: Weatherhoods are strongly recommended for all configurations to help prevent moisture infiltration.
Mounting flange, damper and guard ship factory mounted on all arrangements as shown except when
ordered as a kit.
Mounting Arrangements for Interior Service Applications
Flush interior
2A Exhaust
Flush exterior
The arrangements shown below are the most
commonly used and should be considered first
for most applications. The choice of flush interior
or exterior mounting are based on appearance or
space considerations.
1A Exhaust
Exhaust
Exhaust
Belts, pulleys and motors are serviced from
inside the building with these arrangements. For
applications requiring service from outside the
building, see reverse mounting arrangements below.
Supply
Supply
1B Supply
2B Supply
Mounting Arrangements for Exterior Service Applications (Optional)
Reverse mounting a wall housing simply involves
Flush exterior
Flush interior
installing the wall housing through the wall
opening in the opposite direction of the above
configurations. This results in an opposite effect
on fan function. An exhaust fan in a wall housing
will function as a supply fan when the housing is
reverse mounted.
1A-R Supply
2A-R Supply
Supply
Supply
Exhaust
Example: When the exhaust arrangement shown as
1A is reversed (shown as 1A-R) the same unit now
becomes a supply arrangement. The construction,
fan position and mounting angle location in both
configurations remain identical.
Exhaust
1B-R Exhaust
2B-R Exhaust
EXHAUST FAN in Wall Housing with Gravity
Damper and Weatherhood
Airflow
Pressure Loss
CFM x 1000
SUPPLY FAN in Wall Housing with Gravity
Damper and Weatherhood
Airflow
Pressure Loss
CFM x 1000
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Filtered Supply Wall Housing
Mounting Options
Filtered supply wall housings are available in seven sizes
for fans ranging from size 24 to 54 inches (610 to 1372 mm).
They are designed with the draw-thru concept to achieve the
highest filter and fan efficiencies.
Standard construction is galvanized steel (painted steel
optional). Mounting flanges are factory installed for either flush
exterior or flush interior. Permanent 2 inch (51 mm) washable
filters are accessed through a bolted panel and can be easily
removed for cleaning.
All accessory items available with the standard wall housing can be used with the filtered supply wall housing.
Diffusers - Wall Housing Mounted - Manual Operator
Diffusers are constructed with heavy gauge galvanized steel frames,
blades and prepunched mounting flanges. They are designed to mount to
the interior end of the wall housing when used in the supply configuration.
Manual quadrants set the angle of the blades to deflect air in 1, 2 or 4
Mounting
Closure Angles
directions.
Angles
INTERIOR
EXTERIOR
Closure Angles
An extra set of mounting flanges is available for field installation to close
off the interior wall opening for a finished appearance.
Notes:
Size
A
B
C
Wall Opening
Filter Size & Quantity
1. Additional bracing (by others) above or below the
housing is required for support of the filtered supply
wall housing.
24
30
36
42
48
54
321⁄4 (819)
381⁄4 (972)
441⁄4 (1124)
501⁄8 (1273)
561⁄8 (1426)
63 (1600)
65 (1651)
671⁄4 (1708)
727⁄8 (1851)
727⁄8 (1851)
24 (610)
26 (660)
281⁄4 (718)
34 (864)
34 (864)
333⁄4 (857)
393⁄4 (1010)
453⁄4 (1162)
513⁄4 (1314)
573⁄4 (1467)
633⁄4 (1619)
(4) 231⁄4 (591) x 161⁄4 (413)
(4) 245⁄8 (625) x 191⁄4 (489)
(6) 231⁄4 (591) x 221⁄8 (562)
(6) 241⁄8 (613) x 251⁄8 (638)
(12) 231⁄4 (591) x 183⁄4 (476)
(12) 231⁄4 (591) x 203⁄4 (527)
Attach at least two supports (either vertical or angled)
to the end of housing.
Vertical supports must carry 500# minimum per
support, and angled (45°) supports a minimum of 750#
per support.
623⁄8 (1584) 7911⁄16 (2024) 4011⁄16 (1033)
2. Filtered supply wall housing, fan damper and guards
ship completely factory assembled. Weatherhood
ships loose.
Filters are 2 in (51 mm) nominal thickness. Above filter sizes are actual dimensions. All dimensions given in
inches (mm).
Weatherhood
Weatherhoods shield wall openings and dampers from rain and snow. Weatherhoods are
shipped unassembled in kit form for field assembly. Construction is of galvanized steel with
wire mesh birdscreen. Mounting flanges have prepunched mounting holes. 45° turn down is for
exhaust and 90° turn down is for exhaust and supply. Options include aluminum construction,
insect screen and painted finish.
Damper Guard
Damper guards meet the OSHA requirements completely enclose the damper or wall openings
on the discharge side of the fan. They are constructed of expanded galvanized steel screen in
galvanized steel frames. Mounting flanges have prepunched mounting holes. Options include
aluminum construction and painted finish.
Dampers
Used alone or in conjunction with the wall housing or wall collar, a complete line of dampers is
available for exhaust or supply configurations
FILTERED SUPPLY FAN in Wall Housing with Filter
Bank, Gravity Damper and Weatherhood
Note: This chart is for manual
calculations only. CAPS has
filter losses built into the
selection tool when the filtered
housing option is selected.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Backdraft Dampers
Used alone or in conjunction with the wall housing or wall collar, backdraft dampers are available for exhaust or supply
configurations. Backdraft dampers are constructed with galvanized frames, aluminum blades and vinyl blade seals.
Actuators are available in 24, 120, 208, 230 or 460 volts. Actuators for 50 cycle voltages are also available. Actuators for
50 cycle voltages are also available.
Damper Type
Description
Flush Exterior
Flush Interior
¹
WD-320 and WD-300
exhaust dampers are
available as either gravity
operated or motorized
Exhaust backdraft dampers For applications where the
Exhaust - Gravity or Motorized
are Model WD-320, which
has the prepunched
mounting flange is required
on the inlet end of the
damper (so that the damper
projects to the exterior), the
Model WD-300 is available.
mounting flange located
on the outlet end of the
damper for a flush exterior
appearance.
Airflow
Airflow
Model WD-320 shown
Wall Housing Installation
Wall Installation
²
• WD-430 and WD-420
intake dampers are
only available as gravity
operated
• Model WD-430 has a
prepunched mounting
flange located on the inlet
end of the damper for a
flush exterior appearance
• Model WD-420 is for
applications where a
prepunched mounting
flange is required on the
outlet end of damper (so
the damper projects to
the exterior)
Supply – Gravity
• Galvanized steel frame
and aluminum blades
Airflow
Airflow
• Flange on intake
• Flange on discharge
Wall Housing Installation
Wall Installation
Model WD-430 shown
³
• WD-220 and WD-210
intake dampers are only
available as motorized
• Model WD-220 has a
prepunched mounting
flange located on the inlet
end of the damper for a
flush exterior appearance
• Model WD-210 is for
applications where
a mounting flange is
required on the outlet end
of the damper (so that
the damper projects to
the exterior)
Supply - Motorized
• Galvanized steel frame
and aluminum blades
Airflow
Airflow
• Flange located opposite
of motor side of the
damper
• Flange located on motor
side of the damper
Wall Housing Installation
Wall Installation
Model WD-220 shown
Volume Control/Heavy Duty Dampers
Volume control dampers are available for exhaust or supply configurations and may be used alone or in conjunction
with the wall housing or wall collar. Constructed with heavy galvanized steel frames and blades, model VCD dampers
are designed to handle higher air volumes than the standard backdraft damper. Dampers are available in standard
leakage (VCD-20), low leakage (VCD-23) and insulated low leakage (VCD-34) configurations. Actuators are available in
24, 120, 208, 230 or 460 volts. Actuators for 50 cycle voltages are also available.
Damper Type
Description
Flush Exterior
Flush Interior
Model VCD-20 - Standard leakage The VCD damper has the
N/A
Exhaust or Supply - Motorized
parallel blade set-up and
a prepunched mounting
flange that provides a flush
exterior appearance.
Model VCD-23 - Low leakage
– This damper has blade and jamb
seals for minimal leakage when
closed.
Airflow
Airflow
Model VCD-34 - Insulated low
leakage – This damper has blade
and jamb seals for minimal
leakage when closed. Blades are
constructed with 1⁄2 in. (13 mm)
polystyrene insulation between two
galvanized steel skins.
Wall Installation
Wall Housing Installation
¹
²
³
Model WD-320 and WD-300 are used with fans where the motor is 5 hp or less. For fans with motors larger than 5 hp, the Model GM-31 medium duty gravity backdraft damper or
the Model VCD heavy duty motorized backdraft dampers are required.
Model WD-430 and WD-420 are used with fans where the motor is 5 hp or less. For fans with motors larger than 5 hp, the Model VCD heavy duty motorized backdraft dampers are
required.
Model WD-220 and WD-210 are used with fans where the motor is 3 hp or less. For fans with motors larger than 3 hp, the Model VCD heavy duty motorized backdraft damper is
required.
Note: Wall housing length increases by 6 inches (152 mm) when a heavy duty backdraft damper is specified.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Options and Accessories
Electrical
Disconnect Switches
Toggle type and heavy duty disconnect switches are available for positive
electrical shut-off and safety in servicing fans. The following switches are
available to meet individual electrical requirements and can be factory
mounted or shipped loose for field mounting. Wiring from the motor to the
disconnect box is provided with factory mounted disconnect switches.
• NEMA-1 - General purpose
• NEMA-3R - Rainproof
• NEMA 4 - Watertight
• NEMA-3R & NEMA 4 - Heavy Duty
• NEMA-7 & 9 - for Class 1 and Class 2 hazardous locations.
NEMA-3R
and NEMA-1
1-Point Wiring
Available when the following items are selected: common
voltages on the motor and the actuator, disconnect mounted
and wired and a wall housing. The wires are pulled from the
motor and the actuator on the damper to the disconnect box.
(Hard wiring of the components to the disconnect switch is by
others.)
1-Point wiring
Junction Box
or Disconnect
Exception: When a specific voltage is not available on the
actuator, Greenheck will provide a hard wired transformer
to the actuator. Greenheck will then pull the wires from the
transformer to the disconnect box.
UL/cUL 705
All belt and selected direct drive fans with TE standard efficiency, single speed motors are available with the
UL705 listing for electrical.
Extended Wiring Pigtail
Available only in conjunction with factory mounted disconnect switches, liquid tight wiring pigtails allow direct
hook-up to the power supply which eliminates field wiring at the fan. Internal or external power supply can be
specified.
End Switches
Factory mounted end switches allow the damper to open completely before the fan is energized. This will reduce
the back pressure and brake horsepower load on the fan motor at startup. (Field supplied motor starter with a
relay is required to complete the wiring on a system using an end switch.)
Options
Coatings
A variety of special coatings ranging from enamels to phenolics are available for decorative or protective
purposes. When a special coating is selected for the fan, all accompanying accessory items are also coated
unless so specified. Consult your local representative for more details.
Welded and Painted Fan Construction
For applications where extra heavy construction is required, welded steel construction is available. With this
option, all stationary connections which are normally bolted are welded and coated with an industrial grade
paint. This option applies to belt drive level 3 fans and direct drive level 2 and 3 fans only.
Propeller Fan Rotation Guide
Propeller blade should cup and throw the air when rotating in the correct rotation as shown below.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Basics of Fan Selection
The first consideration in any fan selection is the amount of air to be moved and the resistance to this air
movement. With specific performance and application criteria in mind, propeller fan selections typically
require decisions based on the following criteria.
How Accessories Affect Static Pressure
Belt Drive vs. Direct Drive
All accessory losses must be accounted for when
calculating a fan’s static pressure load. In most
cases dampers, guards and weatherhoods actually
add very little to the total system pressure. This
means that propeller fans used in conjunction with
common accessories can typically be specified
with low pressure capabilities (below 3⁄8 in. wg).
However, in cases where airflow velocities exceed
1500 fpm through the damper or where filters are
used, static pressure loss may be significant. For
more specific information on pressure losses due
to accessories, refer to pages 9 and 10.
Belt drive fans offer the ability to adjust fan speed
for system balancing if necessary. They also offer
more flexibility in speeds and motor selections. In
a cost comparison, belt drive fans are typically less
costly than comparable size direct drive fans with
low speed motors.
Direct drive fans are often preferred for jobs where
maintenance access is difficult. Maintenance costs
are generally lower with direct drive fans, since
there are no belts or bearings to replace and no
pulleys to adjust.
Larger Fans vs. Smaller Fans
Motor Service Factor
In most applications, several fans may meet the
specified airflow and pressure requirements. Just
as larger fans tend to turn slower and generate
less sound, they also tend to have higher initial
costs but lower operating costs. Smaller fans, with
their higher speeds, have more stable performance
curves, lower initial costs, higher sound levels, and
higher operating costs.
Motors for sidewall propeller fans are cooled
by the airstream. With an uninterrupted flow
of cooling air, motors may be operated in their
service factor range (up to 20% above the motor’s
nameplate horsepower) without damage due to
overheating. Lesser overloads are recommended
for applications using totally enclosed or explosion
resistant motors.
Low Sound vs. High Static Pressure
Belt drive performance tables in this catalog show
two speed selections for each propeller type (L or
H) at a given motor hp. The first selection is a 1.0
bhp service factor. The second speed selection is
at 1.2 bhp service factor. Direct drive performance
tables show BHP levels with service factors ranging
up to 1.2 bhp. When a selection at 1.2 bhp service
factor is not desirable for the application, specify
the next higher motor horsepower.
Fans selected for high static pressures run at
higher speeds and produce higher tip speeds,
resulting in higher sound levels. Conversely, in
low pressure applications, fans generally run at
lower speed producing lower sound levels and are
recommended for sound sensitive applications.
Direct Drive Model Number Code
The model number system is designed to completely identify the fan. The correct code letters must be
specified to designate direct drive with exhaust or supply air configuration. The remainder of the model
number is determined by the size and performance selected from pages 15 through 21.
S E 2 - 24 - 6 20 - B 7
Motor HP
Sidewall Roof Propeller
S - Fabricated Prop
SC - Cast Prop
4 = 1⁄4
3 = 1⁄3
5 = 1⁄2
7 = 3⁄4
10 = 1
30 = 3
15 = 11⁄2 50 = 5
20 = 2
75 = 71⁄2
(Level 3 only)
E - Exhaust
S - Supply
R - Reversible
Motor RPM
A = 1750
B = 1160
C = 860
D = 1550
E = 1050
(50Hz)
F = 690
G = 1300
J = 1440
L = 1290
P = 1650
Level of
Construction
1, 2, 3
Fan Size
Blade Pitch
No of Blades
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Drive - Level 1
Dimensional Data: Models SE1/SS1
All direct drive models are available in either exhaust (Model SE1) or supply (Model SS1) arrangements.
Max.
Motor
Frame
Size
Material Gauges
Approx.
Weight
(lbs.)
Panel/Drive frame - Galvanized steel with one-piece drawn venturi
Sizes 8-12; D, G, & E motor speeds - zinc plated heavy welded wire
guard/support structure (paint optional).
Sizes 12-24; A, B, & C motor speeds - bolted structural steel channels
and motor plate. (paint optional).
Propeller - Aluminum blades riveted to a steel hub.
Fan
Fan
Panel
Drive
Frame
Size
8
18
18
18
18
18
18
18
18
-
48
48
15
16
20
27
30
35
39
45
10
12
14
16
18
20
24
-
14*
14
14
14
14
14
48
56
Motors - Heavy duty, permanently lubricated, sleeve bearing type on
sizes 8-12 and ball bearing type on sizes 14-24.
56
56
145T
145T
* A, B, and C motor speeds only. Approximate weight does
not include accessories.
Model SE1 exhaust shown
A Sq.
B*
C*
F*
D
D
Sizes 8-12
D, G, & E
E
Motor Speeds
Exhaust
Supply
Airflow
Airflow
Model SS1 supply shown
A Sq.
B*
C*
F*
D
D
Sizes 12-24
A, B, & C
Motor Speeds
E
Exhaust
Supply
Airflow
Airflow
Fan
Size
Damper
Size**
A Panel**
B*
C*
D
E
F*
8
13 (330)
15 (381)
18 (457)
20 (508)
22 (559)
24 (610)
26 (660)
32 (813)
7 (178)
83⁄4 (222)
103⁄4 (273) 81⁄4 (210)
111⁄4 (286) 81⁄2 (216)
113⁄4 (298) 87⁄8 (225)
5 (127)
5 (127)
1 (25)
1 (25)
1 (25)
1 (25)
1 (25)
83⁄8 (213)
103⁄8 (264) 8 (203)
123⁄8 (314) 131⁄8 (333) 14 (356)
143⁄8 (365) 141⁄4 (362) 16 (406)
163⁄8 (416) 14 (356)
183⁄8 (467) 141⁄4 (362) 20 (508)
8 (203)
10 (254)
10
12
14
16
18
20
24
12 (305)
18 (457)
14 (356)
171⁄4 (438) 11 (279)
20 (508)
125⁄8 (321) 11⁄4 (32) 243⁄8 (619) 21 (533)
107⁄8 (276) 1 (25)
1 (25)
201⁄2 (521) 18 (457)
22 (559)
26 (660)
* Varies with motor selection. All dimensions given in inches (mm). **Square dimension.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Drive - Level 1
Model SE1 for exhaust — Model SS1 for supply
CFM/Static Pressure in Inches WG
0.00 0.05 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75
Motor Fan Max Sones
HP RPM BHP @ F.A.
Model Number
SE1/SS1 Performance Limits
SE1/SS1-8-424-G
SE1/SS1-8-426-D
SE1/SS1-8-428-P
SE1/SS1-8-440-E
SE1/SS1-8-440-G
SE1/SS1-8-440-D
1350 28W
1550 39 W
3.2
3.7
3.9
1.5
3.5
4.9
4.6
4.8
5.2
300
310
329
311
399
459
575
590
606
626
804
924
263
282
302
224
354
419
525
551
573
533
738
869
190
231
266
126
256
351
462
502
536
361
655
800
1/80
190
237
100
198
307
407
468
511
140
214
1/40 1650 53 W
1/100 1050 50 W
1/40 1350 55 W
1/25 1550 75 W
1/50 1550 45 W
149
174
255
138
198
167
272
115
249
SE1/SS1-10-424-D
SE1/SS1-10-426-P
SE1/SS1-10-428-P
SE1/SS1-10-440-E
SE1/SS1-10-440-G
SE1/SS1-10-440-D
SE1/SS1-12-426-D
SE1/SS1-12-436-G
SE1/SS1-12-432-E
SE1/SS1-12-432-G
SE1/SS1-12-432-D
SE1/SS1-12-432-C8
SE1/SS1-12-432-B6
SE1/SS1-12-432-A4
SE1/SS1-14-440-C8
SE1/SS1-14-440-B6
SE1/SS1-14-432-A4
SE1/SS1-14-436-A3
SE1/SS1-16-436-C8
SE1/SS1-16-426-B6
SE1/SS1-16-428-B6
SE1/SS1-16-436-B4
SE1/SS1-16-421-A3
SE1/SS1-16-428-A5
SE1/SS1-16-436-A7
SE1/SS1-18-434-C8
SE1/SS1-18-436-C6
SE1/SS1-18-424-B6
SE1/SS1-18-429-B4
SE1/SS1-18-436-B3
SE1/SS1-18-424-A5
SE1/SS1-18-429-A7
SE1/SS1-20-428-C6
SE1/SS1-20-436-C4
SE1/SS1-20-424-B4
SE1/SS1-20-428-B3
SE1/SS1-20-436-B5
SE1/SS1-20-420-A7
SE1/SS1-20-428-A10
SE1/SS1-20-432-A15
SE1/SS1-24-432-C4
SE1/SS1-24-436-C3
SE1/SS1-24-437-C5
SE1/SS1-24-428-B5
SE1/SS1-24-432-B7
1/30
1/20
55 W
78 W
428
484
1650
407
213
1/40 1050 105 W 3.2
1/20 1350 135 W 4.9
1/12 1550 170 W 5.9
1550 105 W 6.6
1350 120 W 7.5
1/20 1050 125 W 4.3
1/12 1350 170 W 6.0
615
763
929
564
726
877
641
748
779
463
886
1113 1055 975
609
359
383
798
428
721
1/10
1269 1202 1101 1048 973
981 877 744 678 622
1262 1185 1097 1037 986
1449 1382 1309 1271 1224 1129 1042 952
804
540
860
1550 190 W 7.5
614
478
1/8
860 0.03
1/6 1160 0.07
1/4 1750 0.27
860 0.07
1/6 1160 0.15
4.0
4.8
8.7
5.9
7.3
664
511
872
438
816
348
755
248
660
1084 991
503
431
1636 1577 1515 1481 1447 1365 1282 1207 1085 947
1189 1055 919 711 649 551 408
1604 1493 1406 1350 1297 1207 908
706 585
1/8
837
720
1/4
1/3
1/8
0.29
0.39
12.9 2404 2351 2299 2273 2245 2189 2134 2052 1912 1636
14.8 2734 2674 2615 2585 2553 2487 2422 2340 2192 1829 1220
5.0
7.5
7.6
9.5
13.5 2552 2506 2461 2438 2415 2367 2309 2252 2143 1916
15.3 3372 3315 3257 3228 3199 3140 3078 3016 2908 2700 2468 1861
16.6 4076 4015 3954 3923 3892 3828 3760 3693 3591 3349 2902 2298
8.7
9.2
6.7
7.2
12.6 3747 3621 3466 3370 3267 3034 2732 2548 1727 1363
15.7 4224 4151 4079 4043 4006 3925 3835 3745 3592 3252
17.4 4885 4807 4729 4690 4651 4565 4460 4354 4196 3926 3460 2984
10.8 3133 3001 2823 2727 2641 2390 2085 1632
11.7 3888 3717 3523 3420 3285 2918 2237 2091 1873
13.8 3655 3561 3467 3419 3364 3255 3095
14.3 4227 4128 4030 3974 3901 3755 3621 3493 3175 2287
14.4 5245 5118 4991 4926 4849 4697 4525 4321 3863 2920 2650
24
25
26
9.1
1750
860 0.12
0.15
1160 0.19
0.29
2003 1876 1732 1621 1433 1037 849
2108 2027 1942 1894 1846 1725 1588
2235 2148 2058 2012 1964 1840 1710 1534 1126
705
1/6
1/4
1/3
2702 2609 2512 2461 2410 2281 2067 1761 1359 1049
0.38
1/2 1750 0.60
3/4
1/8
0.89
0.15
0.19
0.20
2661 2464 2202 2032 1874 1346
2778 2595 2319 2102 1963 1385 1108 912
2800 2690 2568 2501 2427 2257 2025
860
1/6
1/4 1160 0.30
3238 3120 2987 2908 2828 2668 2434 2145 1510 1183
1/3
1/2
3/4
1/6
0.40
0.60
0.88
0.19
0.29
0.30
1750
860
1/4
1/3 1160 0.40
1/2
3/4
1
11⁄2
1/4
1/3
0.60
0.87
1750 1.19
1.73
0.29
860 0.39
0.58
4682 4617 4552 4519 4486 4421 4362 4303 4215 4036 3810
6377 6311 6246 6214 6181 6116 6050 5965 5820 5580 5368 5087
7115 7038 6962 6924 6886 6809 6733 6653 6518 6292 6016 5688
5000 4767 4540 4409 4233 3789
10.0 5457 5232 5002
11.6 6136 5953 5764 5631 5497 5150 4720 4341
14.1 5908 5794 5680 5623 5566 5382 5175 4898
14.7 6745 6572 6399 6313 6229 6064 5830 5569 5007
1/2
3/4
0.58
0.83
1160
Performance certified is for Models SE1/SS1 for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
Numbers in blue have a larger BHP and require the next size larger motor.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Drive - Level 2
Dimensional Data: Models SE2/SS2
All direct drive models are available in either exhaust (Model SE2) or supply (Model SS2) arrangements.
Material Gauges
Max.
Motor
Frame
Size
Approx.
Weight
(lbs.)
Panel/Drive frame - Galvanized steel with one-piece
drawn venturi, bolted structural steel channels and
motor plate (paint optional).
Propeller - Heavy duty, welded and gusseted painted
steel.
Fan
Fan
Drive
Prop
Hub
Prop
Blade
Size
Panel Frame
16
18
20
24
30
36
42
48
54
18
18
18
18
16
16
14
14
14
14
14
12
12
12
12
10
10
10
14
14
14
14
12
12
11
11
10
16
16
16
16
16
16
14
14
14
56
40
45
56
145T
145T
184T
215T
254T
254T
256T
60
Motors - Heavy duty, permanently lubricated, ball
bearing type.
85
130
230
290
375
465
Approximate weight does not include accessories.
Model SE2 exhaust shown
A Sq.
F*
B*
C*
D
D
E
Exhaust
Supply
Airflow
Airflow
Fan
Damper
Size**
A Panel**
B*
C*
D
E
F*
Size
16
18
20
24
30
36
42
48
54
22 (559)
24 (610)
26 (660)
32 (813)
38 (965)
44 (1118) 201⁄2 (521)
50 (1270) 26 (660)
56 (1422) 265⁄8 (676)
62 (1575) 28 (711)
131⁄2 (343)
131⁄2 (343)
171⁄4 (438)
20 (508)
101⁄4 (260)
101⁄4 (260)
131⁄2 (343)
131⁄2 (343)
163⁄8 (416)
163⁄8 (416)
181⁄4 (464)
205⁄8 (524)
1 (25)
1 (25)
1 (25)
11⁄4 (32) 245⁄8 (625)
11⁄4 (32) 305⁄8 (778)
163⁄8 (416)
183⁄8 (467)
201⁄2 (521)
14 (356)
18 (457)
141⁄4 (362) 20 (508)
18 (457)
21 (533)
22 (559)
26 (660)
213⁄4 (552) 32 (813)
201⁄2 (521)
2 (51)
2 (51)
2 (51)
365⁄8 (930)
425⁄8 (1083) 28 (711)
491⁄4 (1251)
553⁄8 (1407) 301⁄8 (765) 56 (1422)
28 (711)
38 (965)
44 (1118)
281⁄2 (724) 50 (1270)
227⁄16 (570) 2 (51)
* Varies with motor selection. All dimensions given in inches (mm). **Square dimension.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Drive - Level 2
Model SE2 for exhaust — Model SS2 for supply
CFM / Static Pressure in Inches WG
Motor Fan
Max Sones
Model Number
HP RPM BHP @ F.A.
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
SE2 / SS2 Performance Limits
SE2/SS2-16-427-B6
SE2/SS2-16-435-B6
SE2/SS2-16-417-A4
SE2/SS2-16-423-A3
SE2/SS2-16-430-A5
SE2/SS2-18-423-B6
SE2/SS2-18-430-B4
SE2/SS2-18-435-B3
SE2/SS2-18-411-A4
SE2/SS2-18-415-A3
SE2/SS2-18-421-A5
SE2/SS2-20-420-B6
SE2/SS2-20-423-B4
SE2/SS2-20-430-B3
SE2/SS2-20-407-A4
SE2/SS2-20-410-A3
SE2/SS2-20-415-A5
SE2/SS2-20-420-A7
SE2/SS2-20-427-A10
SE2/SS2-20-435-A15
SE2/SS2-24-615-C4
SE2/SS2-24-620-C3
SE2/SS2-24-630-C5
SE2/SS2-24-620-B7
SE2/SS2-24-625-B10
SE2/SS2-24-600-A7
SE2/SS2-24-604-A10
SE2/SS2-24-610-A15
SE2/SS2-24-615-A20
SE2/SS2-30-618-C7
SE2/SS2-30-625-C10
SE2/SS2-30-635-C15
SE2/SS2-30-605-B7
SE2/SS2-30-610-B10
SE2/SS2-30-615-B15
SE2/SS2-30-620-B20
SE2/SS2-36-607-C7
SE2/SS2-36-611-C10
SE2/SS2-36-617-C15
SE2/SS2-36-600-B10
SE2/SS2-36-605-B15
SE2/SS2-36-609-B20
SE2/SS2-36-614-B30
SE2/SS2-42-602-C10
SE2/SS2-42-608-C15
SE2/SS2-42-612-C20
SE2/SS2-42-617-C30
SE2/SS2-42-627-C50
SE2/SS2-48-407-C15
SE2/SS2-48-410-C20
SE2/SS2-48-415-C30
SE2/SS2-48-422-C50
SE2/SS2-54-420-F50
SE2/SS2-54-410-C50
SE2/SS2-54-416-C75
0.15
0.20
0.30
11.3
11.6
18.7
19.9
23
12.5
14.2
16.2
21
22
22
15.3
17.2
18.6
27
2213 1933 1849 1766 1536 1215 894
1/6
1160
2522 2239 2150 2055 1732 1434
1/4
1/3
1/2
1/6
1/4
1/3
1/4
1/3
1/2
1/6
1/4
2582 2414 2375 2336 2255 2156 2053 1869 1435 1084
3076 2899 2854 2809 2719 2621 2524 2331 1916
3531 3344 3297 3250 3155 3058 2944 2750 2303 1642
2917 2632 2562 2458 2249 2018
3376 3038 2944 2861 2662 2398 2084
3658 3311 3208 3089 2850 2556 1903
3121 2978 2941 2893 2799 2697 2586 2415
3623 3476 3439 3400 3300 3199 3091 2920
4177 4015 3975 3931 3807 3683 3574 3416 3059 2558
3697 3350 3257 3137 2857 2532 2155
3997 3626 3522 3419 3153 2834 2430
1750 0.38
0.56
0.20
1160 0.29
0.35
0.30
1750 0.41
0.59
0.21
1160 0.30
0.40
4468 4087 3989 3882 3626 3281
1/3
0.37
0.37
0.57
0.88
1.19
1.76
0.28
3579 3382 3333 3282 3180 3053 2922 2744 2300 1869 1342
4035 3835 3785 3731 3623 3461 3254 3113 2791
4934 4697 4637 4578 4454 4330 4185 3957
5577 5355 5300 5243 5121 4999 4877 4614 4138 3544 2992
6633 6364 6297 6231 6099 5968 5837 5613
7266 6980 6909 6837 6691 6543 6396 6115 5453 4658
4687 4200 4058 3895 3561 3126 2488
5300 4710 4557 4410 3993 3445 2607
28
29
30
33
1/2
3/4
1
11⁄2
1/4
1/3
1/2
3/4
1
3/4
1
11⁄2
2
1750
35
15.7
18.5
18.8
23
25
36
39
40
41
23
28
32
29
30
31
33
27
30
31
34
36
37
40
30
32
33
35
41
43
44
48
53
52
53
860
0.36
0.54
0.86
1.13
0.87
1.18
1.70
2.28
0.79
1.18
1.80
0.86
1.17
1.72
2.29
0.82
1.11
1.61
1.21
1.72
2.34
3.29
1.08
1.73
2.42
3.32
5.95
1.84
2.40
3.58
5.91
5.76
5.68
8.68
6439 5768 5599 5412 4993 4387
7148 6728 6619 6502 6268 6049 5831 5308 4315
7917 7491 7391 7291 7060 6781 6501 6035 4850 2745
5070 4877 4828 4778 4676 4573 4455 4251 3911 3518 3161 2287
6297 6081 6027 5973 5865 5747 5627 5447 5084 4671 4203
8137 7904 7845 7787 7670 7559 7448 7281 6968 6571 6178 5106
9537 9310 9253 9197 9083 8961 8835 8646 8315 7915 7508 6559
9698 9066 8886 8707 8309 7892 7340 6370
1160
1750
860
3/4
1
11515 10823 10644 10461 10097 9629 9051 7945
13290 12505 12291 12076 11647 11060 10192 7951
11⁄2
3/4
1
7911 7479 7369 7257 7034 6795 6551 6210 5496 4497 3377
9662 9293 9201 9103 8872 8640 8392 7976 7204 6248 5108
12000 11565 11456 11348 11130 10890 10619 10200 9404 8327 6921
13905 13434 13316 13198 12939 12665 12391 11954 11144 10136 8640
9985 9347 9183 9012 8669 8255 7829 7039 5325 3679 2486
12131 11529 11360 11187 10840 10449 10058 9289 7622 5532 3782
15162 14491 14324 14153 13810 13442 12926 12117 10512 7704 5270
8200 7791 7656 7515 7224 6913 6617 6214 5478 4679 3902
11977 11535 11424 11313 11077 10828 10580 10147 9384 8487 7337 5080
14957 14468 14345 14223 13976 13728 13480 13098 12411 11537 10483 7678
18400 17945 17832 17718 17490 17263 16965 16517 15787 15003 13722 10993
8673 7991 7811 7632 7254 6888 6531 5979 4937 3944 2850
14642 14035 13883 13732 13396 13058 12692 12072 10980 9558 8035
18363 17675 17503 17331 16966 16600 16233 15619 14477 13041
21840 21148 20975 20802 20440 20032 19624 18975 17694 16259 14629 8191
28811 27924 27702 27480 27037 26533 26023 25261 24002 22494 20376 13589
18124 17081 16823 16565 16049 15499 14820 13815 12067 9984 7536
21801 20853 20616 20362 19848 19333 18699 17684 15807 13843 11719
27004 26027 25783 25539 24915 24272 23638 22726 21025 19172 16924
34332 33166 32874 32583 31944 31257 30570 29594 27990 25869 23518
41542 39736 39284 38845 38011 37177 36322 34995 32089 28911 25289 14535
35642 34502 34217 33932 33364 32826 32287 31334 29690 27722 25548 20120
45612 44465 44179 43892 43319 42745 42051 40967 39103 37130 34973 30171
1160
860
11⁄2
2
3/4
1
11⁄2
1
11⁄2
2
1160
3
1
11⁄2
2
3
5
11⁄2
2
860
860
3
5
690
860
5
71⁄2
54
Performance certified is for Models SE2/SS2 for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
Numbers in blue have a larger BHP and require the next size larger motor.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Drive - Level 3
Dimensional Data: Models SCE3/SCS3
All direct drive models are available in either exhaust (Model SCE3) or supply (Model SCS3) arrangements.
Material Gauges
Drive
Max.
Motor
Frame
Size
Approx.
Weight
(lbs.)
Panel/Drive frame - Galvanized steel with one-piece
drawn venturi, bolted structural steel channels and
motor plate. (paint optional).
Fan
Fan
Prop
Prop Hub
Size Panel Frame
Blade
20
24
30
36
42
48
54
18
18
16
16
14
14
14
12
12
12
12
10
10
10
145T
184T
184T
215T
254T
254T
256T
55
Propeller - Heavy duty, cast aluminum.
80
Motors - Heavy duty, permanently lubricated, ball
bearing type.
125
220
290
386
477
Cast
Cast
Aluminum Aluminum
Prop
Prop
Approximate weight does not include accessories.
Model SCE3 exhaust shown
F*
A sq.
B*
C*
D
D
E
Exhaust
Supply
Airflow
Airflow
Fan
Damper
Size**
A Panel**
B*
C*
D
E
F*
Size
20
24
30
36
42
48
54
26 (660)
32 (813)
38 (965)
44 (1118)
50 (1270)
56 (1422)
62 (1575)
171⁄4 (438)
20 (508)
201⁄2 (521)
201⁄2 (521)
26 (660)
131⁄2 (343)
131⁄2 (343)
163⁄8 (416)
163⁄8 (416)
181⁄4 (464)
205⁄8 (524)
1 (25)
201⁄2 (521)
18 (457)
21 (533)
22 (559)
26 (660)
213⁄4 (552) 32 (813)
11⁄4 (32) 245⁄8 (625)
11⁄4 (32) 305⁄8 (778)
2 (51)
2 (51)
2 (51)
365⁄8 (930)
425⁄8 (1083) 28 (711)
491⁄4 (1251)
553⁄8 (1407) 301⁄8 (765) 56 (1422)
28 (711)
38 (965)
44 (1118)
265⁄8 (676)
281⁄2 (724) 50 (1270)
28 (711)
227⁄16 (570) 2 (51)
* Varies with motor selection. All dimensions given in inches (mm). **Square dimension.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Drive - Level 3
Model SCE3 for exhaust — Model SCS3 for supply
CFM / Static Pressure in Inches WG
Motor Fan Max Sones
HP RPM BHP @ F.A.
Model Number
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
SCE3/SCS3 Performance Limits
SCE3/SCS3-20-617-B4
SCE3/SCS3-20-622-B3
SCE3/SCS3-20-630-B5
SCE3/SCS3-20-307-A4
SCE3/SCS3-20-312-A3
SCE3/SCS3-20-320-A5
SCE3/SCS3-20-327-A7
SCE3/SCS3-20-429-A10
SCE3/SCS3-24-620-C4
SCE3/SCS3-24-627-C3
SCE3/SCS3-24-630-C5
SCE3/SCS3-24-412-B4
SCE3/SCS3-24-417-B3
SCE3/SCS3-24-617-B5
SCE3/SCS3-24-625-B7
SCE3/SCS3-24-630-B10
SCE3/SCS3-24-407-A5
SCE3/SCS3-24-315-A7
SCE3/SCS3-24-415-A10
1/4
0.29
22
23
25
31
33
37
41
42
3243 2990 2924 2851 2703 2529 2292 1796
3766 3517 3451 3381 3241 3067 2871 2468
4394 4115 4049 3984 3809 3635 3448 3039
2984 2707 2629 2554 2410 2250 2083 1789 1213
3753 3486 3424 3364 3240 3087 2909 2623 2082 1415
4673 4463 4383 4304 4152 4011 3873 3667 3222 2608 1804
5504 5189 5129 5069 4931 4772 4613 4365 3931 3335 2471
6005 5797 5745 5692 5564 5434 5303 5106 4739 4327 3763
1/3 1160 0.40
1/2
1/4
1/3
0.55
0.27
0.40
1/2 1750 0.62
3/4
1
1/4
1/3
1/2
1/4
1/3
1/2 1160 0.60
3/4
1
1/2
3/4
1
0.92
1.26
0.28 16.7 4777 4292 4146 3999 3695 3312 2822
860 0.39 16.2 5612 5090 4940 4787 4420 3982 3385
0.45 18.2 5924 5401 5252 5094 4653 4184 3656
0.28 18.8 4685 4204 4105 4007 3762 3481 3172 2538
0.38
21
24
27
28
39
40
46
49
53
5446 4960 4843 4725 4461 4167 3905 3412
5994 5634 5537 5440 5248 5053 4828 4472 3675
7249 6872 6772 6672 6462 6248 6013 5592 4773
7991 7644 7535 7426 7206 6984 6694 6203 5304
5559 5316 5250 5169 5010 4854 4691 4434 3963 3367 2586
7200 6785 6689 6593 6393 6186 6008 5746 5228 4642 3857
7728 7431 7356 7276 7103 6940 6782 6541 6130 5680 5163
8561 8331 8273 8216 8097 7976 7856 7674 7356 7005 6637 5750
9721 9501 9446 9391 9281 9159 9033 8844 8488 8126 7757 6886
0.87
1.10
0.62
0.88
1750 1.17
1.81
SCE3/SCS3-24-615-A15 11⁄2
SCE3/SCS3-24-620-A20
SCE3/SCS3-30-315-C4
SCE3/SCS3-30-320-C3
SCE3/SCS3-30-422-C5
SCE3/SCS3-30-623-C7
SCE3/SCS3-30-627-C10
SCE3/SCS3-30-409-B5
SCE3/SCS3-30-317-B7
SCE3/SCS3-30-612-B10
2
2.37
1/4
1/3
1/2
3/4
1
1/2
3/4
1
0.30 16.5 7276 5972 5609 5236 4402 2816
0.40 19.0 8235 6951 6532 6111 5245 3909
860 0.59
0.87
21
9389 8340 8040 7711 6993 6222 4858
23 10396 9831 9655 9433 8937 8357 7699 6456
23 11192 10384 10182 9958 9484 8897 8174 6869
1.01
0.63
0.85
26
8794 8076 7878 7680 7286 6886 6363 5594 3748
29 10420 9538 9269 9010 8493 7941 7343 6384
1160 1.21
1.87
32 10679 10168 10038 9904 9637 9349 9047 8544 7622 6348
36 13263 12742 12615 12489 12237 11942 11611 11091 10081 8865
40 14779 14160 14005 13849 13537 13220 12901 12376 11276 9927
25 11645 10275 9900 9546 8692 7632 6426
SCE3/SCS3-30-620-B15 11⁄2
SCE3/SCS3-30-625-B20
SCE3/SCS3-36-407-C5
SCE3/SCS3-36-415-C7
SCE3/SCS3-36-612-C10
2
2.32
0.60
0.86
1/2
3/4
1
34 13452 12100 11762 11424 10596 9480 8239
860 1.21
1.75
25 14903 13880 13580 13281 12683 12079 11454 10212
30 17206 16138 15847 15555 14959 14327 13561 12192
31 19898 18735 18408 18081 17299 16428 15538 13942
37 13250 12067 11799 11452 10652 9938 9223 7620 4470
38 14446 13289 13000 12698 12093 11443 10672 9209
43 17128 16145 15888 15629 15110 14561 13964 13052 11211 8411
48 17903 17169 16986 16802 16424 16015 15607 14993 13899 12434 10501
49 21781 20957 20751 20546 20134 19710 19269 18607 17398 15999 14133
25 14274 13009 12625 12182 11224 10210 8748 5893
27 16960 15417 15027 14641 13687 12645 11511 8704
28 20327 18789 18421 17960 17008 15991 14609 11992
31 23088 21265 20790 20297 19236 18050 16564
35 14770 13609 13290 12964 12277 11524 10705 9283 6513
34 17791 16813 16543 16272 15653 14934 14156 12957 9944
35 21138 19913 19598 19283 18657 18039 17251 15978 13640
36 24242 23108 22791 22474 21840 21181 20517 19111 16580 12206
32 18398 15714 14918 14090 12218 10042 6727
SCE3/SCS3-36-620-C15 11⁄2
SCE3/SCS3-36-627-C20
SCE3/SCS3-36-305-B7
SCE3/SCS3-36-307-B10
2
3/4
1
2.30
0.94
1.18
SCE3/SCS3-36-410-B15 11⁄2 1160 1.82
SCE3/SCS3-36-609-B20
SCE3/SCS3-36-617-B30
SCE3/SCS3-42-610-F7
SCE3/SCS3-42-615-F10
2
3
3/4
1
2.42
3.54
0.85
1.16
1.76
2.40
1.16
1.64
2.24
3.11
0.90
1.20
690
860
SCE3/SCS3-42-622-F15 11⁄2
SCE3/SCS3-42-629-F20
SCE3/SCS3-42-605-C10
2
1
SCE3/SCS3-42-610-C15 11⁄2
SCE3/SCS3-42-615-C20
SCE3/SCS3-42-620-C30
SCE3/SCS3-48-410-F7
SCE3/SCS3-48-414-F10
2
3
3/4
1
32 21562 18368 17420 16448 14580 12041 8226
SCE3/SCS3-48-614-F15 11⁄2
690 1.78
2.37
35 25271 23113 22519 21926 20713 19474 17794 14865
38 29125 26642 26019 25396 24108 22773 21122 18057
41 32762 30379 29640 28898 27385 25882 24151 20889
45 23073 21487 21054 20621 19708 18766 17714 16029 12669 7307
48 26491 24711 24266 23812 22881 21974 21083 19377 16101 11261
51 31497 29785 29357 28909 27957 27004 26029 24538 21223
52 39085 37241 36752 36264 35287 34162 33029 31264 27766
53 43290 41324 40745 40167 38989 37745 36536 34864 30731
28 24805 22316 21660 20953 19422 17603 15619 12506
28 30602 27772 27138 26500 25218 23953 22581 19674 11567
31 36325 33687 33047 32411 31012 29503 27774 25025 18028
40 44402 41230 40512 39795 38189 36133 34392 30263 22490
42 22960 20143 19493 18842 17457 15965 14473 12260 8206
42 31594 29768 29284 28783 27774 26704 25565 23289 19595 15339 10240
45 42371 40506 40040 39569 38391 37237 36172 34553 31073 27246 20063
50 51206 48980 48424 47828 46616 45404 44315 42712 39307 35027 29939
SCE3/SCS3-48-619-F20
SCE3/SCS3-48-625-F30
2
3
3.29
1.80
2.33
SCE3/SCS3-48-605-C15 11⁄2
SCE3/SCS3-48-609-C20
SCE3/SCS3-48-614-C30
SCE3/SCS3-48-622-C50
2
3
5
860 3.44
5.61
SCE3/SCS3-48-630-C75 71⁄2
7.66
1.72
2.42
3.47
5.82
2.47
3.51
5.79
9.00
SCE3/SCS3-54-306-F15 11⁄2
SCE3/SCS3-54-311-F20
SCE3/SCS3-54-317-F30
SCE3/SCS3-54-328-F50
SCE3/SCS3-54-300-C20
SCE3/SCS3-54-307-C30
SCE3/SCS3-54-315-C50
2
3
5
2
3
5
690
860
SCE3/SCS3-54-323-C75 71⁄2
Performance certified is for Models SCE3/SCS3 for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
Numbers in blue have a larger BHP and require the next size larger motor.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Drive - Level 3 - Reversible
Dimensional Data: Model SCR3
Material Gauges
Max.
Motor
Frame
Size
Approx.
Weight
(lbs.)
Panel/Drive frame - Galvanized steel with one-piece
drawn venturi, bolted structural steel channels and
motor plate. (paint optional).
Fan
Fan
Drive
Prop
Blade
Prop Hub
Size Panel Frame
24
30
36
42
48
54
16
16
16
14
14
14
14
11
11
10
10
10
184T
184T
215T
254T
254T
256T
80
Propeller - Heavy duty, cast aluminum.
125
220
290
386
477
Motors - Heavy duty, permanently lubricated, ball
bearing type.
Cast
Cast
Aluminum Aluminum
Prop
Prop
Approximate weight does not include accessories.
Model SCR3 reversible shown
B*
A sq.
C*
D
E
Exhaust
Airflow
Supply
Airflow
Fan
Damper
A Panel**
B*
C*
D
E
Size
20
24
30
36
42
48
54
Size**
22 (559)
26 (660)
32 (813)
38 (965)
26 (660)
32 (813)
38 (965)
44 (1118)
50 (1270)
56 (1422)
62 (1575)
171⁄4 (438)
20 (508)
201⁄2 (521)
201⁄2 (521)
26 (660)
131⁄2 (343)
131⁄2 (343)
163⁄8 (416)
163⁄8 (416)
181⁄4 (464)
205⁄8 (524)
1 (25)
201⁄2 (521)
11⁄4 (32) 245⁄8 (625)
11⁄4 (32) 305⁄8 (778)
2 (51)
2 (51)
2 (51)
365⁄8 (930)
425⁄8 (1083) 44 (1118)
491⁄4 (1251)
50 (1270)
553⁄8 (1407) 56 (1422)
265⁄8 (676)
28 (711)
227⁄16 (570) 2 (51)
* Varies with motor selection. All dimensions given in inches (mm). **Square dimension.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Drive - Level 3 - Reversible
Model SCR3 Reversible for exhaust and supply
CFM / Static Pressure in Inches WG
0.00 0.05 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75
Motor Fan Max
HP RPM BHP
Model Number
Sones
24 Performance Limits
SCR3-24-627-C4
SCR3-24-632-C3
SCR3-24-416-B4
SCR3-24-420-B3
SCR3-24-623-B5
SCR3-24-632-B7
SCR3-24-410-A5
SCR3-24-414-A7
SCR3-24-418-A10
SCR3-24-425-A15
SCR3-24-626-A20
1/4
0.29 16.7 4981 4664 4269 4007 3498
860
1/3
1/4
1/3
1/2
3/4
1/2
3/4
1
0.35 16.9 5478 5153 4731 4391 3789
0.29 18.1 4521 4241 3949 3784 3619 3015 2232
0.37 19.3 5200 4904 4597 4434 4271 3815 2837
1160
0.58
0.86
0.57
0.83
22
27
32
34
35
38
41
6093 5869 5627 5499 5371 5029 4529 3791
7389 7148 6896 6739 6582 6207 5689
5233 5028 4828 4730 4632 4403 4167 3921 3364
6297 6114 5930 5834 5738 5546 5331 5108 4625
7332 7141 6949 6853 6752 6552 6348 6112 5758 4623
8928 8701 8474 8364 8259 8050 7831 7581 7160 6055
9935 9786 9636 9561 9486 9325 9155 8984 8707 8111 6996
1750 1.15
1.67
11⁄2
2
2.31
30 Performance
SCR3-30-415-C4
SCR3-30-419-C3
SCR3-30-620-C5
SCR3-30-629-C7
SCR3-30-412-B5
SCR3-30-418-B7
SCR3-30-423-B10
SCR3-30-624-B15
SCR3-30-630-B20
SCR3-30-407-A10
SCR3-30-410-A15
SCR3-30-413-A20
SCR3-30-420-A30
SCR3-30-623-A50
1/4
1/3
1/2
3/4
1/2
3/4
1
0.29 16.6 6262 5732 5131 4718 4013
0.38 17.2 7219 6523 5854 5466 4860
0.56 18.8 8118 7694 7218 6953 6682 5738
860
0.84
0.58
0.88
2
9694 9233 8450 7977 7404
24
27
7490 7051 6640 6429 6211 5688 4914
9414 8921 8440 8206 7968 7466 6763 5490
1160 1.14
1.74
29 10658 10134 9606 9329 8999 8338 7672 6255
33 12167 11796 11425 11239 11041 10647 10032 9244 8158
35 13226 12911 12595 12375 11987 11233 10437 9304
11⁄2
2
2.18
1
1.21
47
8583 8290 7998 7882 7765 7533 7258 6770 6243
11⁄2
2
1.63
46 10337 10022 9712 9571 9429 9146 8892 8652 8266 7375
45 11779 11498 11216 11077 10943 10673 10403 10114 9643 8634
53 15176 14806 14437 14258 14084 13737 13393 13070 12585 11691 10359
63 17896 17658 17419 17300 17180 16942 16703 16454 16067 15380 14269 13199
1750 2.09
3.34
3
5
5.5
36 Performance
SCR3-36-412-C5
SCR3-36-419-C7
SCR3-36-425-C10
SCR3-36-628-C15
SCR3-36-406-B7
SCR3-36-410-B10
SCR3-36-415-B15
SCR3-36-616-B20
SCR3-36-623-B30
SCR3-36-630-B50
1/2
3/4
1
0.55
23
9047 8380 7589 7156 6726
0.85
23 12243 11532 10734 10259 9750 8734
860
1.15
27 14110 13544 12541 12029 11535 10271 8338
31 16432 15855 15258 14814 14370 13429 12309
11⁄2
3/4
1
1.74
0.84
1.14
38
9490 8991 8415 8053 7676
38 10863 10436 9964 9700 9412 8797 8226 7493
11⁄2
2
3
5
1.71
38 14215 13624 13075 12814 12552 11874 11201 10530 9442
44 15749 15311 14874 14666 14468 14071 13650 13183 12407
49 19714 19293 18873 18658 18420 17943 17467 16951 16028 14204
51 23117 22703 22290 22083 21876 21222 20473 19750 18648 16179
1160
2.2
3.44
4.66
42 Performance
SCR3-42-417-F7
SCR3-42-620-F10
SCR3-42-629-F15
SCR3-42-415-C10
SCR3-42-422-C15
SCR3-42-621-C20
SCR3-42-630-C30
SCR3-42-408-B15
SCR3-42-412-B20
SCR3-42-418-B30
SCR3-42-621-B50
SCR3-42-630-B75
3/4
1
0.69
690 1.12
1.72
22 13597 12267 10835 9808 8589
25 16651 15569 14511 13928 13315 11602
11⁄2
1
30 19201 18039 16406 15463 14600 12682
30 16078 14907 13968 13436 12804 11234
1.15
11⁄2
2
1.77
35 18875 17758 16552 15875 15182 13699 11683
36 21190 20336 19478 19048 18614 17612 16541 15213
43 24181 23243 22221 21682 20821 18963 17704 16613
50 15026 14328 13600 13216 12824 11978 10952 9650 7136
51 18959 18189 17432 17066 16700 15890 15029 14017 11855
54 23445 22661 21885 21501 21117 20314 19400 18384 16497
60 28583 27949 27315 26999 26680 26042 25405 24704 23590 21563
73 32616 31921 31226 30878 30483 29683 28884 27018 25357 23149
860
2.28
3
3.48
1.76
2.33
11⁄2
2
3
1160 3.47
5.54
5
71⁄2
8.55
48 Performance
SCR3-48-414-F7
SCR3-48-418-F10
SCR3-48-619-F15
SCR3-48-624-F20
SCR3-48-414-C15
SCR3-48-418-C20
SCR3-48-620-C30
SCR3-48-629-C50
SCR3-48-403-B15
SCR3-48-407-B20
SCR3-48-412-B30
SCR3-48-418-B50
SCR3-48-417-B75
3/4
1
0.87
28 18011 16528 14580 13364 11950
1.17
30 20555 19027 16931 15671 14268 10900
690
11⁄2
2
1.75
33 23382 22284 20801 19931 19057 17136 14215
2.29
1.69
37 26551 25172 23613 22714 21701 19145 15868
11⁄2
2
40 22448 21297 19941 19200 18353 16384 14153
2.27
42 25619 24430 23020 22243 21306 19279 16958 14401
48 30092 29264 28435 27770 27003 25523 24096 22719 19594
56 35190 33738 32249 31430 30610 28531 26291 24091 20049
56 14101 13313 12413 11885 11323 10099 8759
860
3
3.52
5
5.6
1.6
11⁄2
2
2.31
69 20861 20047 19222 18773 18324 17285 16039 14683 12327
69 28014 27172 26330 25844 25330 24303 23202 22039 19654 15119
72 34556 33674 32792 32352 31787 30634 29386 27973 25647 21187
69 37004 36466 35928 35659 35390 34852 34216 33475 32363 30250 27397
3
3.57
1160
5
5.57
71⁄2
8.95
SCR3-48-420-B100 10
54 Performance
11.14 75 41055 40543 40032 39776 39520 39008 38383 37504 36185 34026 31482 28124
SCR3-54-409-F15
SCR3-54-413-F20
SCR3-54-420-F30
SCR3-54-623-F50
SCR3-54-409-C20
SCR3-54-410-C30
SCR3-54-417-C50
SCR3-54-618-C75
11⁄2
2
1.62
2.31
3.48
5.52
2.38
3.37
36 21244 19996 18972 18303 17490 15579 12407
35 25286 24141 22996 22310 21495 19866 17523
690
3
35 32665 31099 29514 28700 27784 25855 23632 20807
5
46 38452 37244 36028 35293 34558 33088 31492 29814 27135
51 26479 25468 24556 24145 23734 22661 21344 19757 16344
53 28003 26997 26093 25707 25320 24416 23141 21715 18977
52 37090 35925 34761 34229 33715 32688 31591 30131 27681 21769
61 41795 40904 40014 39569 39124 38309 37501 36693 35197 31916 25633
68 50142 49192 48243 47768 47283 46066 44850 43285 40770 37198 33806
2
3
5
860 5.81
8.46
71⁄2
SCR3-54-625-C100 10
11.7
Performance certified is for Model SCR3 for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation type A: free inlet
hemispherical sone levels.
21
Numbers in blue have a larger BHP and require the next size larger motor.
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Drive Model Number Code
The model number system is designed to completely identify the fan. The correct code letters must be
specified to designate belt drive with exhaust or supply air configuration. The remainder of the model
number is determined by the size and performance selected from pages 26 through 38.
SB E - 2 L 24 - 7
Motor HP
Sidewall Belt Drive
SB - Fabricated Propeller
SBC - Cast Propeller
(Level 3 only)
4= 1⁄4 15 = 11⁄2 75 = 71⁄2
3= 1⁄3 20 = 2
5= 1⁄2 30 = 3
7= 3⁄4 50 = 5
10= 1
100 = 10
150 = 15
200 = 20
E - Exhaust
S - Supply
For specific motor limitations and
availability see page 31.
R - Reversible
Fan Size
Level of
Construction
1, 2, 3
Propeller Type
L - Low
H - High
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Drive - Level 1
Dimensional Data: Models SBE-1/SBS-1
All belt drive models are available in either exhaust (Model SBE-1) or supply (Model SBS-1) arrangements.
Material Gauges
Max
Propeller - Galvanized steel, riveted blades
Approx.
Weight
(lbs.)
Propeller
Shaft Motor
(aluminum optional).
Fan
Fan
Drive
Size Panel Frame
Size
Frame
Size
Hub
Blade
Bearings - Stamped steel pillow blocks up to size 36
and cast pillow blocks for size 42 and larger.
L
H
L
H
3
20
24
30
36
42
48
54
18
18
18
18
16
16
16
14
14
12
12
12
12
12
14
16 18
16 18
16
⁄
⁄
⁄
⁄
4
4
4
4
56
56
60
70
Panel/Drive frame - Galvanized steel with
one-piece drawn venturi, bolted structural steel
channels and one-piece motor/bearing plate (paint
optional).
3
3
3
14
14 12
14 12
12 11
12 11
12 11
56
95
16
145T
145T
145T
145T
110
150
175
205
14
1
1
1
14
14
Approximate weight does not include accessories.
Model SBE-1H exhaust shown
B
A
sq.
F
D
C
D
E
E
x
haust
Supply
A
ir
f
l
o
w
Airflow
Fan
Size
Damper
Size**
A Panel**
B
C
D
E
F
20
24
30
36
42
48
54
26 (660)
32 (813)
38 (965)
191⁄2 (495) 161⁄4 (413) 1 (25)
191⁄2 (495) 161⁄8 (410) 11⁄4 (32) 245⁄8 (625)
221⁄2 (572) 181⁄4 (464) 11⁄4 (32) 305⁄8 (778) 21 (533) 32 (813)
365⁄8 (930)
23 (584) 38 (965)
201⁄2 (521)
20 (508) 22 (559)
20 (508) 26 (660)
44 (1118) 211⁄2 (546) 161⁄2 (419) 2 (51)
50 (1270) 25 (635)
56 (1422) 25 (635)
62 (1575) 25 (635)
20 (508)
19 (483)
2 (51)
2 (51)
423⁄4 (1086) 23 (584) 44 (1118)
483⁄4 (1238) 23 (584) 50 (1270)
551⁄4 (1403) 24 (610) 56 (1422)
191⁄2 (495) 2 (51)
All dimensions given in inches (mm). **Square dimension.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Drive - Level 2
Dimensional Data: Models SBE-2/SBS-2
Material Gauges
Propeller
Hub Blade
Max
Propeller - Reinforced galvanized steel, riveted
Approx.
Weight
(lbs.)
Shaft Motor
blades, keyed hub.
Fan
Fan
Drive
Size
Frame
Size
Size Panel Frame
Bearings - Cast iron pillow blocks with grease
fittings.
L
H
L
H
3
20
24
30
36
42
48
54
60
18
18
18
18
16
16
16
14
14
14
12
12
12
12
12
12
14
16 18
16 18
16
⁄
4
4
145T
145T
184T
184T
184T
184T
184T
215T
65
Panel/Drive frame - Galvanized steel with
one-piece drawn venturi, bolted structural steel
channels and one-piece motor/bearing plate (paint
optional).
3
14
⁄
75
14 12
14 12
12 11
12 11
12 11
3⁄16 in
1
100
115
160
260
315
370
16
1
14
11⁄4
11⁄4
11⁄4
11⁄2
14
14
12
Approximate weight does not include accessories.
Model SBE-2L exhaust shown
B
A
sq.
F
C
D
E
E
x
haust
Supply
A
ir
f
l
o
w
Airflow
Fan
Damper
Size**
A Panel**
B
C
D
E
F
Size
20
24
30
36
42
48
54
60
26 (660)
32 (813)
38 (965)
191⁄2 (495) 161⁄4 (413)
191⁄2 (495) 161⁄8 (410)
211⁄2 (546) 171⁄4 (438)
1 (25)
201⁄2 (521)
20 (508)
20 (508)
21 (533)
22 (559)
22 (559)
26 (660)
32 (813)
38 (965)
11⁄4 (32) 245⁄8 (625)
11⁄4 (32) 305⁄8 (778)
44 (1118) 211⁄2 (546) 161⁄2 (419)
2 (51)
2 (51)
2 (51)
2 (51)
365⁄8 (930)
50 (1270) 25 (635)
56 (1422) 25 (635)
62 (1575) 26 (660)
68 (1727) 28 (711)
20 (508)
19 (483)
201⁄2 (546)
423⁄4 (1086) 251⁄2 (648) 44 (1118)
483⁄4 (1238) 251⁄2 (648) 50 (1270)
551⁄4 (1403) 24 (610)
611⁄4 (1556) 24 (610)
56 (1422)
62 (1575)
217⁄16 (545) 2 (51)
All dimensions given in inches (mm). **Square dimension.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Drive - Level 3 and Reversible
Dimensional Data: Models SBE-3/SBS-3, SBCE-3/SBCS-3 and SBCR
Material Gauges
Max
Approx.
Weight
(lbs.)
Propeller
Shaft Motor
Size Frame
Size
Propellers- SBE-3/SBS-3 - Heavy duty, welded,
reinforced, steel blades coated in Permatector™.
SBCE-3/SBCS-3 - Heavy duty, cast aluminum blades.
All with keyed hubs.
Fan
Fan
Drive
Hub Blade
Steel Steel
Size Panel Frame
3
24
30
36
42
48
54
60
72
16
16
16
14
14
14
14
12
14
12
12
12
12
10
10
10
12
12
12
11
11
16
16
16
14
14
14
12
12
⁄4
145T
184T
184T
215T
215T
254T
256T
256T
90
140
260
320
420
590
755
1050
1
1
Bearings - Cast iron pillow blocks with grease fittings.
Panel/Drive Frame - Galvanized steel with one-piece
drawn venturi, bolted structural steel channels and
one-piece motor/bearing plate on sizes 24-36, two piece
on sizes 42-72 (all-welded panel/drive frame optional,
paint optional).
11⁄2
11⁄2
11⁄2
13⁄4
2
10
3⁄16 in
3⁄16 in
Approximate weight does not include accessories.
LEVEL 3 — Model SBE-3L exhaust shown
B
A sq.
F
D
C
D
E
Exhaust
Supply
Airflow
Airflow
REVERSIBLE — Model SBCR reversible shown
A sq.
B
C
D
E
Exhaust
Airflow
Supply
Airflow
Fan
Size
Damper
Size**
A Panel**
B
C
D
E
F
24
30
36
42
48
54
60
72
32 (813)
19 (483)
155⁄8 (397) 11⁄4 (32)
245⁄8 (625) 201⁄2 (521) 26 (660)
38 (965) 211⁄2 (546) 171⁄4 (438) 11⁄4 (32)
305⁄8 (778)
365⁄8 (930)
20 (508)
27 (686)
32 (813)
38 (965)
44 (1118)
50 (1270)
28 (711)
28 (711)
23 (584)
23 (584)
2 (51)
2 (51)
2 (51)
423⁄4 (1086) 291⁄4 (743) 44 (1118)
483⁄4 (1238) 301⁄2 (775) 50 (1270)
56 (1422) 311⁄2 (800) 271⁄2 (699)
62 (1575) 353⁄4 (908) 301⁄4 (768)
2 (51) 551⁄4 (1403) 361⁄4 (921) 56 (1422)
611⁄4 (1556) 351⁄2 (902) 62 (1575)
68 (1727)
82 (2083)
35 (889) 287⁄16 (722) 2 (51)
35 (889)
281⁄4 (718) 21⁄8 (54) 731⁄4 (1861) 351⁄2 (902) 74 (1880)
All dimensions given in inches (mm). **Square dimension.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using The Performance Table
Shown below is a portion of a typical performance table used in this catalog. Performance data shown
offers the best selections for each propeller type (“L” or “H”) relative to sound, RPM and static pressure.
Consider “L” type propellers first for most applications.
Many sidewall applications can be met with the “L” type propeller. When using the performance tables, look
first at the “L” selections, because they offer the lowest speed and sound levels.
CFM / Static Pressure in Inches WG
Motor Fan Max
HP RPM BHP
Model Number
*Sones
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Level 1 Performance
Max RPM L - 1085 H - 1221
Max Motor Frame Size - 56
TS = RPM x 5.235
705 0.17 11.6 3606 2836 2451
“L” type
low pressure
propeller
CFM values
shown in
SBE/SBS-1L20-4
SBE/SBS-1H20-4
1/4
1/4
810 0.25 13.3 4143 3510 3325 3084
861 0.30 14.3 4404 3795 3672 3455
773 0.17 11.1 2904 2453 2293 2112 1596 924
892 0.27 14.1 3351 2987 2873 2744 2436 2011 1409 886
953 0.30 16.2 3581 3247 3148 3034 2769 2469 2002 1160 657
889 0.33 14.9 4547 3950 3830 3655 3067
947 0.40 16.1 4844 4271 4156 4044 3648
998 0.37 16.7 3750 3436 3342 3244 3006 2727 2398 1588 873
1039 0.40 17.2 3904 3608 3517 3427 3212 2954 2676 2037 1064 603
1021 0.50 17.0 5222 4675 4566 4461 4181 3747
1085 0.60 17.9 5550 5021 4919 4817 4621 4269 3712
black are the
most efficient
selections.
Values shown
in gray are not
recommended.
676
304
348
“H” type
high pressure
propeller
SBE/SBS-1L20-3
SBE/SBS-1H20-3
SBE/SBS-1L20-5
SBE/SBS-1H20-5
1/3
1/3
1/2
1/2
393
1107 0.50 18.0 4159 3885 3805 3720 3534 3315 3065 2599 1368 935
502
1221 0.60
20
4587 4339 4277 4203 4049 3873 3675 3333 2514 1456 1064
Shows level of
Note that each max.
BHP is cataloged at
a 1.0 and 1.2 service
factor. See page 13.
Optimum selection
range for the “L” type
propeller.
Optimum selection
range for the “H”
type propeller.
construction based on
fan RPM & motor frame
size. See Performance
Charts.
20 Belt Drive SBE/SBS
Model SBE for exhaust — Model SBS for supply
CFM / Static Pressure in Inches WG
Motor Fan Max
HP RPM BHP
Model Number
*Sones
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Level 1 Performance
Max RPM L - 1085 H - 1221
Max Motor Frame Size - 56
TS = RPM x 5.235
705 0.17 11.6 3606 2836 2451
CFM values shown in
SBE/SBS-1L20-4
SBE/SBS-1H20-4
1/4
1/4
810 0.25 13.3 4143 3510 3325 3084
861 0.30 14.3 4404 3795 3672 3455
773 0.17 11.1 2904 2453 2293 2112 1596 924
black are the most efficient
selections. Values shown in
gray are not recommended.
676
304
892 0.27 14.1 3351 2987 2873 2744 2436 2011 1409 886
348
953 0.30 16.2 3581 3247 3148 3034 2769 2469 2002 1160 657
889 0.33 14.9 4547 3950 3830 3655 3067
947 0.40 16.1 4844 4271 4156 4044 3648
998 0.37 16.7 3750 3436 3342 3244 3006 2727 2398 1588 873
1039 0.40 17.2 3904 3608 3517 3427 3212 2954 2676 2037 1064 603
1021 0.50 17.0 5222 4675 4566 4461 4181 3747
SBE/SBS-1L20-3
SBE/SBS-1H20-3
SBE/SBS-1L20-5
1/3
1/3
1/2
1/2
393
1085 0.60 17.9 5550 5021 4919 4817 4621 4269 3712
1107 0.50 18.0 4159 3885 3805 3720 3534 3315 3065 2599 1368 935
502
SBE/SBS-1H20-5
Level 2 Performance
SBE/SBS-2L20-5
1221 0.60
20
4587 4339 4277 4203 4049 3873 3675 3333 2514 1456 1064
Max Motor Frame Size - 143T TS = RPM x 5.235
Max RPM L - 1241 H - 1391
1021 0.50 17.0 5222 4675 4566 4461 4181 3747
1085 0.60 17.9 5550 5021 4919 4817 4621 4269 3712
1107 0.50 18.0 4159 3885 3805 3720 3534 3315 3065 2599 1368 935
1/2
1/2
3/4
3/4
502
SBE/SBS-2H20-5
SBE/SBS-2L20-7
SBE/SBS-2H20-7
1221 0.60
1168 0.75
1241 0.90
1262 0.75
1391 0.90
20
20
22
21
25
4587 4339 4277 4203 4049 3873 3675 3333 2514 1456 1064
5974 5466 5371 5275 5090 4861 4527
6348 5853 5764 5674 5496 5325 5053 4479
4742 4501 4441 4375 4226 4065 3883 3562 2849 1635 1255 495
5226 5008 4954 4899 4774 4639 4493 4244 3741 3005 1886 1138
Performance certified is for Models SBE/SBS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
24 Belt Drive SBE/SBS
Model SBE for exhaust — Model SBS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
Model Number
*Sones
HP
RPM BHP
Level 1 Performance
Max RPM L - 809 H - 1010
Max Motor Frame Size - 56
TS = RPM x 6.283
513 0.19 10.3 4818 3784
CFM values shown in
black are the most efficient
selections. Values shown in
gray are not recommended.
SBE/SBS-1L24-4
1/4
558 0.25 11.0 5241 4402 3971
593 0.30 11.8 5569 4803 4551 4050
674 0.17 10.2 3524 2894 2680 2416 1616 1155 821
SBE/SBS-1H24-4
SBE/SBS-1L24-3
SBE/SBS-1H24-3
SBE/SBS-1L24-5
SBE/SBS-1H24-5
1/4
1/3
1/3
1/2
1/2
3/4
785 0.30 13.3 4105 3618 3445 3267 2848 2105 1655 1133 444
614 0.33 12.4 5766 5040 4807 4396
653 0.40 12.8 6133 5466 5256 5037
829 0.33 14.8 4335 3877 3734 3568 3220 2595 2006 1445 769
877 0.36 16.1 4586 4157 4041 3887 3564 3179 2472 1845 1108 491
704 0.50 13.8 6612 6000 5831 5628 4992
748 0.60 14.8 7025 6455 6300 6128 5723 4939
961 0.55 18.5 5025 4641 4535 4428 4145 3846 3485 2574 1701 1103 540
1010 0.60 19.9 5281 4920 4819 4717 4471 4193 3902 3093 2108 1439 904
775 0.67 15.5 7279 6732 6582 6430 6061 5383
SBE/SBS-1L24-7
809 0.76 17.4 7598 7079 6935 6792 6454 5948 5237
Level 2 Performance
Max RPM L - 986 H - 1148
Max Motor Frame Size - 143T
TS = RPM x 6.283
688 0.47 13.5 6461 5833 5652 5444 4730
704 0.50 13.8 6612 6000 5831 5628 4992
748 0.60 14.8 7025 6455 6300 6128 5723 4939
SBE/SBS-2L24-5
1/2
961 0.55 18.5 5025 4641 4535 4428 4145 3846 3485 2574 1701 1103 540
1010 0.60 19.9 5281 4920 4819 4717 4471 4193 3902 3093 2108 1439 904
805 0.75 17.1 7560 7038 6894 6750 6408 5882 5170
SBE/SBS-2H24-5
SBE/SBS-2L24-7
SBE/SBS-2H24-7
SBE/SBS-2L24-10
1/2
3/4
3/4
1
856 0.90
1110 0.85
1148 0.90
886 1.00
942 1.20
960 1.27
986 1.37
21
23
25
23
28
30
33
8039 7555 7419 7284 6989 6654 6011
5804 5476 5392 5299 5115 4872 4619 4200 2975 2199 1601 626
6003 5685 5606 5518 5340 5122 4882 4502 3343 2510 1853 910
8321 7856 7726 7595 7326 7003 6512
8847 8409 8294 8171 7925 7643 7340 6476
9016 8587 8476 8355 8114 7847 7549 6769
SBE/SBS-2L24-15
11⁄2
9260 8842 8738 8620 8385 8139 7849 7205
Level 3 Performance
Max RPM L - 1127 H - 1485
Max Motor Frame Size - 145T
TS = RPM x 6.283
838 0.49 15.5 6598 6001 5836 5599 5047 4507
SBE/SBS-3L24-7
SBE/SBS-3H24-7
3/4
3/4
964 0.75
1024 0.90
21
24
7590 7084 6945 6802 6429 5961 5459 4645
8062 7592 7463 7329 7034 6634 6154 5492
1099 0.50 18.5 5732 5377 5281 5184 4983 4756 4514 4095 2979
1263 0.78
1330 0.90
1061 1.00
1127 1.20
1392 1.00
1485 1.18
22
24
25
27
25
28
6588 6286 6203 6119 5952 5776 5593 5277 4680 3710 2590
6937 6650 6576 6496 6337 6174 6007 5721 5195 4494 3495
8354 7902 7778 7651 7392 7016 6588 5914
8873 8454 8337 8220 7977 7686 7321 6668 5569
7261 6987 6918 6842 6690 6538 6378 6124 5639 5071 4170
7746 7489 7425 7358 7216 7073 6928 6704 6271 5793 5208 3470
SBE/SBS-3L24-10
SBE/SBS-3H24-10
1
1
Performance certified is for Models SBE/SBS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
Numbers in blue have a larger BHP and require the next size larger motor.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
30 Belt Drive SBE/SBS
Model SBE for exhaust — Model SBS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
*Sones
Level 1 Performance
Max RPM L - 696 H - 882
390 0.16 9.5 6453
448 0.25 10.9 7413 5790
475 0.30 11.6 7860 6394 5880
503 0.17 9.4 5747 4619 4164
Max Motor Frame Size - 56
TS = RPM x 7.854
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBE/SBS-1L30-4
SBE/SBS-1H30-4
1/4
1/4
577 0.25 11.8 6593 5682 5389 5018
610 0.30 12.6 6970 6129 5860 5559 4743
491 0.33 12.1 8125 6742 6249
523 0.40 13.0 8654 7427 6970 6503
631 0.33 13.1 7210 6396 6156 5888 5163
675 0.40 14.1 7713 6950 6763 6515 5939 5160
564 0.50 14.3 9333 8261 7862 7436
598 0.60 15.5 9895 8898 8583 8185 7366
725 0.50 15.5 8284 7571 7398 7213 6746 6145
769 0.60 16.9 8787 8112 7949 7785 7376 6876 6248
645 0.75 17.2 10673 9766 9508 9190 8446 7562
SBE/SBS-1L30-3
SBE/SBS-1H30-3
SBE/SBS-1L30-5
SBE/SBS-1H30-5
SBE/SBS-1L30-7
SBE/SBS-1H30-7
1/3
1/3
1/2
1/2
3/4
685
827 0.75 19.1 9450 8819 8667 8515 8188 7779 7279 6326
882 0.90 22 10078 9484 9342 9199 8914 8560 8174 7424
696 0.94 19.2 11517 10696 10456 10217 9570 8874
Max RPM L - 950 H - 1221 Max Motor Frame Size - 184T
0.9
18.7 11335 10496 10253 10009 9332 8622
3/4
1
SBE/SBS-1L30-10
Level 2 Performance
TS = RPM x 7.854
645 0.75 17.2 10673 9766 9508 9190 8446 7562
685 0.90 18.7 11335 10496 10253 10009 9332 8622
827 0.75 19.1 9450 8819 8667 8515 8188 7779 7279 6326
SBE/SBS-2L30-7
SBE/SBS-2H30-7
SBE/SBS-2L30-10
SBE/SBS-2H30-10
SBE/SBS-2L30-15
SBE/SBS-2H30-15
SBE/SBS-2L30-20
3/4
3/4
1
882 0.90
22 10078 9484 9342 9199 8914 8560 8174 7424
710 1.00 19.7 11748 10949 10714 10479 9872 9192 8383
754 1.20
917 1.00
968 1.20
812 1.50
864 1.81
1048 1.50
1110 1.80
895 2.00
950 2.41
1152 2.00
1221 2.40
21 12477 11736 11519 11298 10806 10175 9528
23 10478 9906 9768 9631 9357 9049 8680 8012
26 11061 10519 10385 10255 9996 9736 9403 8847 7570
24 13436 12749 12570 12364 11954 11426 10838 9893
27 14297 13650 13489 13309 12923 12522 11971 11132
29 11975 11474 11349 11227 10987 10747 10507 10029 9071
31 12683 12211 12092 11974 11747 11521 11294 10901 10090 9019
29 14810 14186 14030 13868 13496 13123 12633 11830
32 15720 15132 14985 14838 14503 14152 13790 13039 11760
33 13163 12708 12594 12480 12259 12041 11823 11483 10749 9811
36 13951 13522 13414 13307 13095 12889 12683 12374 11734 10955 9980
1
11⁄2
11⁄2
2
SBE/SBS-2H30-20
2
Level 3 Performance
Max RPM L - 1100 H - 1432
Max Motor Frame Size - 184T
TS = RPM x 7.854
824 1.51
905 2.01
961 2.40
1076 1.53
1182 2.04
1260 2.40
1036 3.01
1100 3.61
1353 3.01
1432 3.53
23 13052 12289 12098 11898 11483 11006 10403 9137
26 14335 13640 13467 13293 12924 12540 12102 11263 9366
29 15222 14568 14404 14241 13905 13549 13167 12519 10795
30 11401 11026 10932 10833 10601 10369 10102 9652 8854 7967 6444
35 12524 12182 12097 12012 11820 11609 11398 11026 10338 9590 8780 5817
38 13351 13030 12950 12870 12708 12510 12312 12015 11376 10705 9980 8065
35 16410 15803 15651 15500 15196 14874 14544 13993 12801 11093
41 17423 16852 16709 16566 16281 15991 15680 15201 14241 12775 11254
44 14336 14037 13963 13888 13739 13574 13390 13113 12580 11984 11343 9939
49 15173 14891 14820 14750 14609 14468 14297 14036 13586 13022 12446 11176
SBE/SBS-3L30-20
SBE/SBS-3H30-20
2
2
SBE/SBS-3L30-30
SBE/SBS-3H30-30
3
3
Performance certified is for Models SBE/SBS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
Numbers in blue have a larger BHP and require the next size larger motor.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
36 Belt Drive SBE/SBS
Model SBE for exhaust — Model SBS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
*Sones
Level 1 Performance
Max RPM L - 551 H - 694
Max Motor Frame Size - 56
TS = RPM x 7.854
329 0.25 12.3 9491 6448
1/3 361 0.34 11.8 10415 7958 6849
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBE/SBS-1L36-3
SBE/SBS-1H36-3
384 0.40 11.8 11078 8915 8018 6662
410 0.25 10.0 9011 6831 6112
1/3 450 0.33 11.1 9890 7967 7391 6725
481 0.40 12.1 10572 8812 8290 7743
412 0.50 12.7 11886 9913 9250 8354
438 0.61 13.6 12636 10809 10290 9572
521 0.52 13.5 11451 9845 9398 8912 7811
556 0.61 14.9 12220 10729 10328 9891 8958
471 0.76 14.5 13588 11925 11442 10947 9408
500 0.90 15.3 14425 12890 12435 11981 10808 8915
591 0.75 16.4 12989 11605 11223 10844 9985 9016
628 0.90 18.2 13802 12520 12156 11800 11035 10205 9228
SBE/SBS-1L36-5
SBE/SBS-1H36-5
SBE/SBS-1L36-7
SBE/SBS-1H36-7
SBE/SBS-1L36-10
1/2
1/2
3/4
3/4
518 1.01 16.1 14944 13482 13044 12605 11569 10084
551 1.21 17.7 15896 14558 14146 13733 12908 11731 10007
1
651 1.01 18.8 14308 13083 12731 12386 11668 10880 9995
SBE/SBS-1H36-10
Level 2 Performance
SBE/SBS-2L36-10
1
694 1.23
20
15253 14135 13798 13468 12824 12111 11358 9875
Max RPM L - 693 H - 870
Max Motor Frame Size - 184T
TS = RPM x 7.854
518 1.01 16.1 14944 13482 13044 12605 11569 10084
550 1.21 17.6 15867 14525 14113 13699 12873 11682 9934
651 1.01 18.8 14308 13083 12731 12386 11668 10880 9995
1
1
SBE/SBS-2H36-10
SBE/SBS-2L36-15
SBE/SBS-2H36-15
SBE/SBS-2L36-20
694 1.23
593 1.51
631 1.81
744 1.50
792 1.80
653 2.01
693 2.41
821 2.02
870 2.40
20
20
22
23
27
24
27
30
34
15253 14135 13798 13468 12824 12111 11358 9875
17108 15909 15527 15144 14377 13512 12329
11⁄2
11⁄2
2
18204 17113 16759 16400 15680 14959 14025 12176
16352 15358 15021 14714 14106 13486 12810 11706
17407 16519 16198 15894 15316 14753 14145 13170
18839 17784 17467 17120 16424 15728 14942 13287
19993 18999 18744 18416 17762 17106 16450 15154
18044 17217 16907 16601 16043 15496 14935 14011 12258
19121 18388 18096 17803 17259 16736 16223 15389 13871
SBE/SBS-2H36-20
2
Level 3 Performance
Max RPM L - 819 H - 1321
Max Motor Frame Size - 184T
TS = RPM x 7.854
614 1.52 18.1 16901 15679 15294 14909 14075 13113 11866
SBE/SBS-3L36-20
SBE/SBS-3H36-20
2
2
675 2.02
716 2.41
833 1.52
915 2.04
967 2.40
771 3.01
819 3.60
1046 3.00
1106 3.60
1241 5.01
1321 6.00
20
22
26
30
33
25
28
38
40
52
59
18580 17464 17178 16828 16128 15335 14463 12727
19709 18646 18404 18098 17438 16759 15972 14576
15014 14373 14212 14041 13682 13275 12740 11908 10095
16492 15908 15762 15616 15299 14972 14598 13867 12585 10735 8063
17429 16877 16739 16600 16313 16003 15694 15059 13876 12427 10502
21223 20222 19997 19772 19169 18556 17898 16802 14296
SBE/SBS-3L36-30
SBE/SBS-3H36-30
SBE/SBS-3H36-50
3
3
5
22544 21590 21378 21166 20658 20081 19504 18511 16505
18853 18342 18215 18087 17831 17554 17268 16833 15767 14646 13192
19935 19452 19331 19210 18968 18721 18450 18044 17147 16121 15045 11743
22368 21937 21830 21722 21507 21291 21076 20715 20113 19273 18372 16280
23810 23405 23304 23203 23001 22799 22596 22277 21711 21077 20233 18473
Performance certified is for Models SBE/SBS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
Numbers in blue have a larger BHP and require the next size larger motor.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
42 Belt Drive SBE/SBS
Model SBE for exhaust — Model SBS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
*Sones
Level 1 Performance
Max RPM L - 424 H - 533
250 0.24 9.4 11651
275 0.33 10.3 12816 8583
294 0.40 11.1 13701 10026
Max Motor Frame Size - 145T
TS = RPM x 10.995
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBE/SBS-1L42-3
SBE/SBS-1H42-3
1/3
1/3
314 0.25
9.4 10844 7332
345 0.33 11.1 11915 9126 7744
369 0.40 12.6 12744 10191 9283
316 0.50 12.0 14726 11363 10252
SBE/SBS-1L42-5
SBE/SBS-1H42-5
SBE/SBS-1L42-7
SBE/SBS-1H42-7
SBE/SBS-1L42-10
1/2
1/2
3/4
3/4
1
335 0.60 13.0 15612 12415 11671 10248
400 0.51 14.7 13814 11527 10841 9931
426 0.61 16.3 14712 12605 11980 11333
362 0.75 14.5 16870 13939 13189 12422
385 0.90 15.8 17942 15273 14451 13804 11298
460 0.78 18.5 15887 13987 13420 12834 11361
482 0.90
20
16646 14868 14327 13784 12592 10507
398 1.00 16.8 18548 16016 15189 14528 12837
424 1.21 18.8 19759 17478 16705 15953 14777
500 1.00
533 1.22
20
21
17268 15573 15060 14539 13448 11853
18408 16849 16388 15899 14900 13752 11887
SBE/SBS-1H42-10
Level 2 Performance
SBE/SBS-2L42-10
1
Max RPM L - 723 H - 907
Max Motor Frame Size - 184T
TS = RPM x 10.995
398 1.00 16.8 18548 16016 15189 14528 12837
424 1.21 18.8 19759 17478 16705 15953 14777
1
1
500 1.00
533 1.22
456 1.50
484 1.80
577 1.53
608 1.81
502 2.01
532 2.40
630 2.00
673 2.41
575 3.01
611 3.60
721 3.00
766 3.61
681 5.08
723 6.00
853 4.99
907 5.95
21
22
21
23
24
26
24
27
28
31
32
31
36
40
36
39
48
56
17268 15573 15060 14539 13448 11853
18408 16849 16388 15899 14900 13752 11887
21251 19152 18532 17809 16577 15188
SBE/SBS-2H42-10
SBE/SBS-2L42-15
SBE/SBS-2H42-15
SBE/SBS-2L42-20
SBE/SBS-2H42-20
SBE/SBS-2L42-30
SBE/SBS-2H42-30
SBE/SBS-2L42-50
11⁄2
11⁄2
2
22555 20599 20064 19420 18117 17086 15458
19927 18529 18109 17678 16773 15831 14681
20998 19701 19302 18903 18053 17182 16275 14193
23394 21521 21006 20440 19128 18098 16824
24792 23046 22560 22074 20881 19757 18819 16579
21758 20527 20142 19757 18951 18122 17251 15564
23243 22131 21771 21411 20682 19906 19122 17893
26796 25212 24762 24312 23339 22193 21216 19836
2
3
28474 26984 26586 26162 25316 24279 23201 21952 18527
24900 23864 23572 23236 22564 21861 21137 20017 17604
3
26455 25479 25235 24931 24298 23664 22982 21961 20125 16908
31736 30400 30066 29712 28952 28192 27265 25814 23967 20093
33693 32435 32120 31805 31102 30386 29642 28275 26322 24165
29459 28583 28364 28145 27603 27035 26466 25556 24003 22312 19563
31324 30500 30294 30088 29630 29095 28561 27738 26299 24797 22915
5
SBE/SBS-2H42-50
5
Level 3 Performance
Max RPM L - 762 H - 951
Max Motor Frame Size - 184T
TS = RPM x 10.995
527 1.99 18.3 22520 20843 20397 19944 18862 17664 16166
SBE/SBS-3L42-30
SBE/SBS-3H42-30
3
3
606 3.00
640 3.61
657 1.99
755 3.00
800 3.60
714 5.02
762 6.01
893 5.01
951 6.00
24
26
24
30
31
30
33
37
43
25896 24438 24073 23695 22908 21971 20980 19316
27349 25968 25623 25278 24537 23737 22813 21321 17720
19872 18805 18554 18303 17771 17180 16461 15333 13065
22836 21890 21671 21453 21016 20567 20053 19187 17554 15662
24197 23301 23090 22883 22471 22059 21605 20878 19377 17765 15725
30512 29274 28964 28655 28028 27360 26666 25424 23169 19687
32563 31403 31113 30823 30243 29634 29008 27942 25934 23434
27010 26207 26007 25816 25447 25078 24709 24107 22961 21608 20168 16141
28764 28010 27822 27634 27286 26939 26592 26072 25063 23863 22589 19606
SBE/SBS-3L42-50
SBE/SBS-3H42-50
5
5
Performance certified is for Models SBE/SBS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
Numbers in blue have a larger BHP and require the next size larger motor.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
48 Belt Drive SBE/SBS
Model SBE for exhaust — Model SBS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
*Sones
Level 1 Performance
Max RPM L - 355 H - 429
Max Motor Frame Size - 145T
TS = RPM x 12.566
231 0.31
266 0.50
282 0.60 10.5 18171 14077 11902
278 0.33 9.6 14144 9240
320 0.50 11.3 16281 12822 11273 8844
341 0.61 12.3 17349 14214 13047 11371
305 0.76 11.8 19653 16196 14706 12401
324 0.90 13.0 20877 17700 16601 14948
368 0.76 13.6 18723 15953 15022 13860
393 0.93 15.5 19995 17450 16655 15783 13052
335 1.00 13.7 21586 18559 17626 16200
355 1.20 15.4 22875 20096 19220 18193 14778
408 1.04 16.4 20758 18314 17617 16777 14587
8.6 14885
9.7 17140 12381
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBE/SBS-1L48-5
SBE/SBS-1H48-5
1/2
1/2
SBE/SBS-1L48-7
SBE/SBS-1H48-7
SBE/SBS-1L48-10
3/4
3/4
1
SBE/SBS-1H48-10
Level 2 Performance
SBE/SBS-2L48-10
1
429 1.21
1.3 21827 19513 18907 18147 16322 13506
Max Motor Frame Size - 184T
Max RPM L - 608 H - 734
TS = RPM x 12.566
335 1.00 13.7 21586 18559 17626 16200
1
1
355 1.20 15.4 22875 20096 19220 18193 14778
408 1.04 16.4 20758 18314 17617 16777 14587
429 1.21 19.3 21827 19513 18907 18147 16322 13506
384 1.51 17.9 24744 22197 21482 20668 18419
407 1.80 18.9 26226 23841 23203 22474 20720 17923
SBE/SBS-2H48-10
SBE/SBS-2L48-15
SBE/SBS-2H48-15
SBE/SBS-2L48-20
SBE/SBS-2H48-20
SBE/SBS-2L48-30
SBE/SBS-2H48-30
SBE/SBS-2L48-50
11⁄2
11⁄2
2
462 1.51
491 1.81
21
22
23506 21374 20811 20248 18770 16860 13759
24981 22990 22460 21930 20671 19129 16981
422 2.00 19.6 27192 24904 24289 23637 22154 19746
448 2.40
509 2.02
540 2.41
483 3.03
513 3.60
582 3.01
618 3.61
572 5.02
608 5.99
688 4.99
734 6.05
21
23
24
23
28
27
29
33
36
34
39
28868 26733 26154 25575 24229 22469 19898
25897 23985 23474 22963 21831 20485 18700 14388
27474 25681 25206 24724 23761 22529 21119 18065
31123 29170 28633 28096 26963 25668 23839 19730
33056 31241 30735 30230 29218 28043 26799 23721
29611 27947 27527 27081 26187 25232 24055 21925
31442 29875 29484 29078 28236 27395 26391 24703 20285
36858 35237 34822 34368 33461 32554 31504 29811 24906
39177 37652 37271 36864 36010 35157 34288 32745 29209
35004 33596 33244 32893 32158 31402 30646 29317 26560 22373
37344 36025 35695 35365 34700 33991 33283 32220 29911 26937 22215
2
3
3
5
SBE/SBS-2H48-50
5
Level 3 Performance
Max RPM L - 686 H - 862
Max Motor Frame Size - 215T
TS = RPM x 12.566
415 1.99 18.0 27276 24912 24215 23465 21703 19225
SBE/SBS-3L48-30
SBE/SBS-3H48-30
3
3
477 3.03
506 3.61
519 1.98
597 3.01
634 3.62
565 5.02
600 6.02
707 5.01
754 6.01
646 7.51
686 9.00
809 7.51
862 9.01
23
25
24
30
33
30
33
41
44
38
44
48
54
31351 29261 28772 28223 26914 25381 23672
33257 31277 30810 30350 29181 27830 26385 23228
23494 22018 21590 21159 20227 19128 18054 16079
27025 25742 25421 25066 24316 23547 22590 21178 18405
28700 27492 27190 26888 26184 25479 24681 23333 20969 17480
37135 35361 34918 34499 33657 32570 31377 29437 24082
SBE/SBS-3L48-50
SBE/SBS-3H48-50
SBE/SBS-3L48-75
SBE/SBS-3H48-75
5
39435 37765 37347 36934 36157 35241 34217 32427 28734
32004 30921 30650 30379 29816 29183 28550 27492 25489 23319 20320
34132 33116 32862 32608 32100 31530 30937 30047 28205 26350 24136
42459 40907 40520 40132 39389 38667 37749 36264 33435 28965
45088 43627 43262 42896 42175 41495 40773 39429 36866 33882
36622 35675 35438 35202 34728 34249 33696 32866 31331 29575 27852 22774
39021 38132 37910 37688 37244 36800 36324 35546 34248 32623 30989 27270
5
71⁄2
71⁄2
Performance certified is for Models SBE/SBS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
Numbers in blue have a larger BHP and require the next size larger motor.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
54 Belt Drive SBE/SBS
Model SBE for exhaust — Model SBS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
*Sones
Level 1 Performance
Max RPM L - 343 H - 377
Max Motor Frame Size - 145T
TS = RPM x 13.135
224 0.51
257 0.77
272 0.90
244 0.49
281 0.75
299 0.91
283 1.03
300 1.21
310 1.01
329 1.21
325 1.56
343 1.81
355 1.52
377 1.82
10.7 19676 12031
12.0 22575 17498 14789
12.7 23892 19346 17418 14251
10.6 18660 13392
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBE/SBS-1L54-7
SBE/SBS-1H54-7
3/4
3/4
12.2 21490 17541 16040
13.4 22867 19233 18136 16425
13.3 24859 20604 19008 16462
14.1 26352 22515 21155 19430
14.0 23708 20252 19215 17828
15.6 25161 21986 21010 20033
16.5 28548 25088 24008 22726 18692
17.3 30129 26851 26014 24825 21850 16537
17.4 27149 24310 23414 22509 20237
19.0 28832 26243 25408 24557 22802 19924
SBE/SBS-1L54-10
SBE/SBS-1H54-10
SBE/SBS-1L54-15
1
1
11⁄2
11⁄2
SBE/SBS-1H54-15
Level 2 Performance
SBE/SBS-2L54-15
Max RPM L - 508 H - 562
Max Motor Frame Size - 184T
16.5 28548 25088 24008 22726 18692
17.3 30129 26851 26014 24825 21850
17.4 27149 24310 23414 22509 20237
19.0 28832 26243 25408 24557 22802 19924
18.0 31271 28113 27322 26297 23790
19.6 33379 30420 29680 28940 26821 23826
TS = RPM x 13.135
325 1.56
343 1.81
355 1.52
377 1.82
356 2.00
380 2.41
390 2.01
414 2.41
408 3.07
433 3.61
446 3.01
474 3.61
478 4.87
508 5.97
528 4.99
562 6.03
11⁄2
11⁄2
2
SBE/SBS-2H54-15
SBE/SBS-2L54-20
SBE/SBS-2H54-20
SBE/SBS-2L54-30
SBE/SBS-2H54-30
SBE/SBS-2L54-50
20
22
22
26
26
30
35
44
35
40
29826 27374 26567 25750 24103 21767
2
31662 29444 28684 27924 26374 24628 21971
35839 33083 32394 31704 30019 27876 24657
38035 35439 34789 34139 32810 30926 28749
34109 32145 31468 30762 29338 27897 26104
36250 34402 33873 33209 31882 30526 29170 26145
41988 39636 39048 38459 37283 36006 34299 31347
44623 42410 41857 41303 40196 39088 37699 35194 28363
40380 38721 38307 37854 36662 35469 34252 32427 27435
42980 41422 41032 40643 39618 38498 37370 35655 32079
3
3
5
SBE/SBS-2H54-50
5
Level 3 Performance
Max RPM L - 619 H - 779
Max Motor Frame Size - 254T
TS = RPM x 13.135
339 1.97
390 3.01
415 3.61
430 2.03
491 3.00
526 3.62
463 5.01
492 6.02
584 5.01
618 6.02
530 7.51
563 9.03
666 7.38
710 9.02
584 10.04
619 12.00
738 10.01
779 12.00
20
25
27
27
33
38
40
44
48
52
46
49
57
63
51
56
68
75
29862 26277 25025 23452 19663
SBE/SBS-3L54-30
SBE/SBS-3H54-30
3
3
34354 31312 30531 29462 26898 24533 21251
36557 33708 32974 32162 30005 27535 24061
27612 25569 25157 24640 23580 22036 20032
31529 29634 29274 28913 28053 27125 25868 23501
33776 31946 31609 31272 30565 29698 28831 26933
40785 38252 37593 36935 35395 33426 31153 26792
43339 40968 40348 39728 38489 36778 34740 31783 26116
37501 35765 35447 35144 34537 33881 33101 31897 28836
39684 38044 37683 37396 36823 36250 35558 34451 32025 28547
46687 44501 43926 43351 42200 40903 39302 36323 30423
49594 47550 47008 46467 45384 44301 42910 40440 36084 30683
42766 41244 40864 40558 40026 39494 38962 37956 36129 33526
45591 44164 43807 43450 42943 42444 41945 41121 39515 37449 34796
51443 49482 48960 48438 47394 46350 45173 42994 38597 33058
54526 52685 52198 51706 50721 49736 48751 46840 42826 39077 33870
47389 46016 45673 45329 44791 44311 43831 43111 41571 39835 37550
50022 48721 48396 48070 47487 47032 46578 45895 44548 43085 41129 35732
SBE/SBS-3L54-50
SBE/SBS-3H54-50
SBE/SBS-3L54-75
SBE/SBS-3H54-75
SBE/SBS-3L54-100
SBE/SBS-3H54-100
5
5
71⁄2
71⁄2
10
10
Performance certified is for Models SBE/SBS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
Numbers in blue have a larger BHP and require the next size larger motor.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
60 Belt Drive SBE/SBS
Model SBE for exhaust — Model SBS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
*Sones
Level 2 Performance
Max RPM L - 399 H - 521
Max Motor Frame Size - 215T
TS = RPM x 15.691
219 0.99
1 1/2 252 1.52
267 1.80
285 0.98
1 1/2 328 1.50
348 1.81
11.8 29223
14.9 33627 26297
16.7 35628 28888 26731
19.3 25029 21665 20507 19031
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBE/SBS-2L60-15
SBE/SBS-2H60-15
23
25
28805 25931 25163 24307 21827
30561 27858 27152 26428 24458 21479
277 2.01
294 2.41
361 2.01
383 2.41
317 3.02
337 3.63
415 3.01
438 3.60
375 5.00
399 6.02
489 5.00
521 6.01
17.9 36963 30532 28569
SBE/SBS-2L60-20
SBE/SBS-2H60-20
SBE/SBS-2L60-30
SBE/SBS-2H60-30
SBE/SBS-2L60-50
2
20
26
28
23
25
31
34
28
31
42
47
39231 33280 31524 29592
31703 29065 28432 27734 25998 23625
33635 31095 30577 29920 28558 26588 23870
42300 36880 35324 33661
2
3
44969 39902 38533 37026 33664
36445 34024 33548 33054 31839 30400 28519
38465 36115 35664 35214 34128 32978 31354 28368
50040 45536 44345 43137 40410 37274
53242 49009 47929 46800 44361 41676 38401
42944 40718 40314 39911 39104 38087 37057 34972 29773
45754 43590 43208 42830 42072 41233 40266 38708 34835
3
5
SBE/SBS-2H60-50
5
Level 3 Performance
Max RPM L - 503 H - 659
Max Motor Frame Size - 256T
TS = RPM x 15.691
317 3.02
375 5.00
399 6.02
415 3.01
489 5.00
521 6.01
430 7.54
457 9.05
559 7.51
595 9.00
473 10.04
503 12.10
615 10.00
659 12.00
23
28
31
31
42
47
41
56
51
56
67
72
60
70
42300 36880 35324 33661
50040 45536 44345 43137 40410 37274
SBE/SBS-3L60-50
SBE/SBS-3H60-50
5
5
53242 49009 47929 46800 44361 41676 38401
36445 34024 33548 33054 31839 30400 28519
42944 40718 40314 39911 39104 38087 37057 34972 29773
45754 43590 43208 42830 42072 41233 40266 38708 34835
57379 53451 52469 51451 49333 46970 44412
SBE/SBS-3L60-75
SBE/SBS-3H60-75
SBE/SBS-3L60-100
SBE/SBS-3H60-100
7 1/2
7 1/2
1 0
60982 57286 56362 55438 53476 51359 49101 45184
49091 47075 46626 46274 45568 44862 44021 42669 39714 35627
52253 50358 49884 49518 48855 48192 47529 46261 43933 40629 35715
63117 59546 58653 57760 55891 53922 51775 48286
67120 63762 62923 62083 60374 58582 56644 53530
54009 52176 51718 51314 50673 50031 49389 48236 46188 43214 39510
57873 56163 55735 55307 54653 54054 53455 52537 50625 48395 45470
1 0
72 Belt Drive SBE/SBS
Model SBE for exhaust — Model SBS for supply
Level 3 Performance
Max RPM L - 492 H - 559
Max Motor Frame Size - 256T
TS = RPM x 18.802
236 2.00
271 3.02
288 3.61
266 2.00
306 3.01
324 3.61
321 5.05
341 6.01
362 5.04
387 6.03
367 7.52
391 9.03
414 7.52
442 9.01
405 10.01
430 12.10
456 10.02
486 12.00
463 15.10
492 18.00
522 15.00
559 18.10
17.5 41661 36581 34402 32305
47840 43440 42315 40635 36937
SBE/SBS-3L72-30
3
3
20
22
24
28
30
26
29
35
39
33
38
43
50
41
45
51
57
52
57
64
75
50841 46713 45654 44576 40999
40185 35934 34790 33352 29513
46228 42491 41629 40634 38280 35026
SBE/SBS-3H72-30
48947 45342 44616 43707 41829 39122 35680
56667 52986 52036 51086 48805 45604 42580
60197 56743 55852 54958 53170 50373 47427
54688 51305 50655 50006 48405 46723 44302 39813
58465 55195 54588 53980 52646 51074 49325 45737
64787 61577 60768 59938 58276 56442 53627 49588
69024 66011 65258 64489 62930 61371 59275 55346
62543 59374 58806 58238 57102 55698 54228 51410 44663
66773 63726 63155 62623 61559 60428 59051 56986 51688
71495 68587 67859 67128 65622 64117 62514 58687
75909 73169 72484 71799 70395 68977 67559 64603 58769
68888 65934 65321 64806 63775 62743 61437 59435 54874 47671
73421 70649 69956 69464 68496 67529 66500 64622 60962 55889
81734 79190 78554 77918 76637 75320 74003 72027 66649 61379
86854 84459 83861 83262 82065 80838 79599 77740 73537 68410
78859 76279 75633 75025 74124 73223 72322 70752 67837 63842 58785
84449 82039 81436 80834 79872 79030 78189 76927 74244 71276 67313
SBE/SBS-3L72-50
SBE/SBS-3H72-50
SBE/SBS-3L72-75
SBE/SBS-3H72-75
SBE/SBS-3L72-100
SBE/SBS-3H72-100
SBE/SBS-3L72-150
SBE/SBS-3H72-150
5
5
7 1/2
7 1/2
1 0
1 0
1 5
1 5
Performance certified is for Models SBE/SBS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
24-30 Belt Drive SBCE/SBCS
Cast Aluminum
Model SBCE for exhaust — Model SBCS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
24 Performance
*Sones
Max RPM L - 1194 H - 1396
Max Motor Frame Size - 145T
TS = RPM x 6.283
707 0.25 11.7 4871 4203 3934 3666 3046
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBCE/SBCS-3L24-3
SBCE/SBCS-3H24-3
1/3
1/3
777 0.33 13.3 5353 4759 4578 4333 3826 3181
828 0.40 14.6 5704 5156 5000 4804 4346 3836
829 0.25 13.1 4726 4160 4012 3859 3528 3131 2459 998
911 0.33 15.2 5193 4686 4549 4414 4128 3824 3457 1842 771
968 0.40 16.7 5518 5046 4917 4788 4531 4251 3945 3338 1239
892 0.50 16.3 6145 5646 5503 5358 4955 4525 4034
SBCE/SBCS-3L24-5
SBCE/SBCS-3H24-5
SBCE/SBCS-3L24-7
SBCE/SBCS-3H24-7
SBCE/SBCS-3L24-10
1/2
1/2
3/4
3/4
1
948 0.60 18.0 6531 6070 5936 5800 5474 5073 4647 3825
1043 0.50 18.7 5946 5515 5394 5274 5038 4790 4529 4086 1820 1066
1108 0.60
1021 0.75
1085 0.90
1194 0.75
1268 0.90
1124 1.00
1194 1.20
1314 1.00
1396 1.20
20
20
21
22
23
22
24
24
26
6317 5917 5803 5690 5466 5244 5001 4621 3734 1589 878
7034 6617 6493 6368 6116 5761 5390 4774
7475 7092 6975 6858 6622 6349 5999 5463
6807 6438 6339 6233 6023 5817 5609 5268 4627 3509 1584
7229 6881 6794 6696 6498 6301 6107 5800 5243 4536 2159 917
7743 7380 7267 7154 6927 6698 6362 5856 4888
8225 7892 7788 7682 7469 7253 7004 6527 5677
7491 7156 7072 6981 6790 6599 6412 6124 5603 4981 3940 1304
7958 7643 7564 7485 7306 7126 6948 6684 6208 5685 5051 1966
SBCE/SBCS-3H24-10
30 Performance
1
Max RPM L - 1262 H - 1616
Max Motor Frame Size - 184T
TS = RPM x 7.854
569 0.33 13.0 7847 6270 5795 5113
SBCE/SBCS-3L30-5
SBCE/SBCS-3H30-5
1/2
1/2
654 0.50 15.2 9019 7723 7321 6931 5825
695 0.60 16.6 9585 8388 8025 7647 6798
728 0.33 14.5 7043 6131 5893 5647 5111 4342 3084
837 0.50 17.6 8097 7305 7109 6902 6478 6018 5432 4155
890 0.60 19.1 8610 7863 7681 7492 7098 6696 6238 5288
749 0.75 18.5 10329 9246 8927 8580 7894 6971
SBCE/SBCS-3L30-7
SBCE/SBCS-3H30-7
SBCE/SBCS-3L30-10
SBCE/SBCS-3H30-10
3/4
3/4
1
795 0.90
958 0.75
1018 0.90
824 1.00
875 1.20
1055 1.00
1121 1.20
943 1.50
1002 1.80
1207 1.50
1283 1.80
1038 2.00
1103 2.40
1329 2.00
1412 2.40
1188 3.00
1262 3.60
1521 3.00
1616 3.60
20
21
23
21
23
24
26
25
28
30
34
29
32
35
39
36
40
43
47
10964 9966 9665 9359 8700 7988 6979
9268 8571 8402 8233 7875 7504 7125 6434 4568
9848 9190 9031 8872 8544 8201 7850 7277 5927
11364 10408 10126 9836 9204 8587 7726
12067 11169 10927 10653 10081 9486 8839 7440
10206 9569 9416 9263 8951 8623 8286 7759 6591 4668
10845 10242 10098 9954 9665 9362 9051 8572 7667 6305
13005 12173 11962 11727 11220 10666 10120 9119
1
SBCE/SBCS-3L30-15 11⁄2
SBCE/SBCS-3H30-15 11⁄2
13818 13038 12839 12640 12168 11672 11148 10388
11677 11117 10980 10846 10578 10308 10022 9584 8814 7822 6497
12412 11886 11754 11627 11375 11122 10863 10458 9762 8982 7921
14315 13562 13370 13178 12740 12277 11771 11028 9312
15211 14504 14324 14143 13762 13329 12877 12162 10837
12857 12349 12222 12097 11853 11610 11366 10976 10309 9588 8680 5623
13660 13182 13062 12943 12712 12483 12254 11898 11279 10645 9926 7863
16383 15727 15562 15394 15059 14678 14275 13631 12547 11117
17404 16786 16632 16475 16159 15835 15456 14881 13842 12738 11164
14715 14271 14160 14049 13829 13617 13404 13085 12521 11939 11347 9800
15634 15216 15111 15007 14798 14596 14396 14096 13579 13041 12487 11270
SBCE/SBCS-3L30-20
SBCE/SBCS-3H30-20
SBCE/SBCS-3L30-30
SBCE/SBCS-3H30-30
2
2
3
3
Performance certified is for Models SBCE/SBCS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
36-42 Belt Drive SBCE/SBCS
Cast Aluminum
Model SBCE for exhaust — Model SBCS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
36 Performance
*Sones
Max RPM L - 1183 H - 1480
Max Motor Frame Size - 184T
TS = RPM x 9.424
516 0.50 16.8 11939 9557 8829
593 0.75 19.4 13721 11814 11168 10528
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBCE/SBCS-3L36-7
SBCE/SBCS-3H36-7
3/4
3/4
630 0.90
21 14577 12834 12261 11645 10267
644 0.50 16.4 11014 9546 9133 8714 7772 6388
740 0.75 19.3 12655 11375 11058 10720 9987 9269 8128 5237
786 0.90
652 1.00
693 1.20
814 1.00
865 1.20
747 1.50
793 1.80
932 1.50
991 1.81
822 2.01
873 2.41
1026 2.00
1090 2.41
939 3.00
998 3.61
1174 3.00
1248 3.60
1113 5.01
1183 6.01
1392 5.00
1480 6.01
21 13442 12239 11937 11639 10951 10296 9439 7708
22 15086 13432 12900 12305 11146
24 16034 14528 14037 13515 12409
21 13921 12764 12467 12179 11539 10887 10251 8712
24 14793 13713 13424 13152 12595 11952 11363 10148 6816
26 17284 15904 15505 15043 14034 13022
SBCE/SBCS-3L36-10
SBCE/SBCS-3H36-10
SBCE/SBCS-3L36-15
1
1
11⁄2
28 18348 17064 16709 16301 15395 14424 13478
27 15939 14947 14679 14413 13910 13358 12764 11955 9834
29 16948 16024 15773 15521 15038 14565 14009 13209 11486 8916
29 19019 17789 17447 17085 16238 15296 14379
SBCE/SBCS-3H36-15 11⁄2
SBCE/SBCS-3L36-20
SBCE/SBCS-3H36-20
SBCE/SBCS-3L36-30
SBCE/SBCS-3H36-30
SBCE/SBCS-3L36-50
2
2
3
3
5
5
32 20199 19058 18736 18414 17658 16812 15930 14506
31 17547 16654 16418 16174 15701 15243 14737 13939 12515 10428
35 18641 17801 17589 17360 16902 16471 16041 15285 14101 12341 9976
35 21726 20687 20387 20088 19454 18719 17906 16689
39 23092 22127 21851 21569 21006 20343 19635 18470 16315
39 20078 19297 19102 18902 18477 18060 17661 17032 15873 14769 12962
43 21343 20609 20426 20242 19850 19449 19067 18503 17426 16390 15077 10981
47 25752 24888 24672 24424 23919 23413 22823 21871 20143 18120
51 27372 26559 26355 26145 25670 25194 24713 23837 22246 20647
51 23806 23148 22983 22819 22490 22132 21773 21255 20412 19413 18480 15976
58 25311 24692 24537 24382 24073 23751 23413 22909 22117 21253 20313 18538
SBCE/SBCS-3H36-50
42 Performance
Max RPM L - 916 H - 1259
Max Motor Frame Size - 184T
TS = RPM x 10.995
459 0.76 15.0 15668 12712 11573
SBCE/SBCS-3L42-10
1
504 1.00 17.1 17205 14534 13822 12742
536 1.20 18.1 18297 15764 15173 14440
630 0.75
692 1.00
736 1.20
23 14710 13176 12736 12261 11152 9826 8273
25 16158 14789 14403 14003 13096 12041 10833 8546
27 17185 15919 15558 15190 14411 13492 12420 10692
SBCE/SBCS-3H42-10
SBCE/SBCS-3L42-15
1
577 1.50 19.7 19696 17316 16771 16196 14444
11⁄2
613 1.80
793 1.50
842 1.80
635 2.00
675 2.40
872 2.00
927 2.40
727 3.00
773 3.61
998 3.00
1061 3.61
862 5.01
916 6.01
1184 5.01
1259 6.01
21 20925 18692 18147 17635 16364 14566
29 18516 17367 17032 16698 16004 15223 14370 12822 9458
31 19660 18600 18285 17970 17329 16671 15872 14556 11992
23 21676 19551 18980 18485 17376 15648
SBCE/SBCS-3H42-15 11⁄2
SBCE/SBCS-3L42-20
SBCE/SBCS-3H42-20
SBCE/SBCS-3L42-30
SBCE/SBCS-3H42-30
SBCE/SBCS-3L42-50
SBCE/SBCS-3H42-50
2
2
3
3
5
5
25 23042 21097 20492 20012 19068 17750 16130
33 20361 19351 19047 18743 18130 17495 16775 15590 13189 9576
36 21645 20721 20435 20149 19576 18987 18390 17308 15214 12754
29 24817 23036 22520 21969 21104 20153 18783
31 26387 24729 24278 23762 22864 22051 21080 18935
40 23303 22459 22211 21945 21414 20882 20328 19443 17697 15606 13168
44 24774 23980 23776 23526 23026 22526 22019 21236 19699 17881 15890
37 29425 27971 27566 27161 26242 25478 24749 23472 20356
42 31269 29920 29539 29158 28347 27517 26831 25762 23038
51 27645 26934 26756 26579 26135 25687 25239 24559 23384 21956 20349 16653
57 29397 28728 28561 28393 28011 27590 27168 26536 25446 24224 22881 19615
Performance certified is for Models SBCE/SBCS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
48-54 Belt Drive SBCE/SBCS
Cast Aluminum
Model SBCE for exhaust — Model SBCS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
48 Performance
*Sones
Max RPM L - 908 H - 1182
Max Motor Frame Size - 215T
TS = RPM x 12.566
435 0.99 18.5 21897 17413 15801
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBCE/SBCS-3L48-15
SBCE/SBCS-3H48-15
11⁄2
11⁄2
500 1.51
531 1.80
566 0.99
650 1.50
691 1.80
550 2.00
585 2.32
716 2.01
761 2.40
630 3.01
669 3.50
819 3.00
871 3.60
746 5.00
793 5.88
971 5.00
1032 6.00
854 7.50
908 8.88
1112 7.51
1182 9.00
23
24
23
28
31
25
27
33
35
30
32
39
43
38
41
53
59
45
50
67
75
25169 21295 20354 19165
26730 23117 22183 21212
21010 18533 17717 17010 15233 13144 9229
24128 21973 21464 20750 19481 17983 16242 12200
25650 23608 23130 22600 21313 20083 18535 15959
27686 24227 23288 22434
29448 26249 25335 24494 22640
26578 24598 24136 23675 22413 21279 19918 17513
28249 26368 25935 25501 24434 23316 22195 20084 15370
31713 28809 27962 27113 25587 23623
33676 30972 30203 29404 27904 26301
SBCE/SBCS-3L48-20
SBCE/SBCS-3H48-20
SBCE/SBCS-3L48-30
SBCE/SBCS-3H48-30
SBCE/SBCS-3L48-50
SBCE/SBCS-3H48-50
SBCE/SBCS-3L48-75
2
2
3
30402 28632 28231 27827 27020 25867 24889 23274 19744 13540
32332 30648 30270 29892 29133 28230 27191 25779 22761 19268
37552 35186 34519 33835 32401 31082 29675
3
5
39918 37729 37102 36474 35144 33810 32626 30464
36044 34496 34157 33818 33140 32459 31682 30277 28102 25291 22178
38308 36841 36509 36191 35553 34913 34272 33002 30995 28669 25923 16703
42989 41003 40421 39838 38648 37395 36190 34476
45707 43860 43334 42786 41690 40528 39350 37736 34664
41278 39917 39577 39282 38690 38098 37504 36601 34556 32687 30384 25026
43876 42596 42275 41971 41415 40859 40300 39461 37668 35918 34068 29382
5
71⁄2
71⁄2
SBCE/SBCS-3H48-75
54 Performance
Max RPM L - 727 H - 856
Max Motor Frame Size - 254T
TS = RPM x 14.135
364 1.51 18.0 25482 21713 20664 19377
SBCE/SBCS-3L54-20
SBCE/SBCS-3H54-20
2
2
400 2.01
425 2.41
429 1.51
471 2.00
501 2.41
458 3.01
487 3.60
539 3.00
573 3.61
543 5.02
577 5.96
639 5.00
680 6.02
621 7.51
660 9.01
732 7.52
778 9.00
20
22
21
23
26
25
28
29
31
33
38
37
41
44
49
47
53
28002 24618 23706 22752 19950
29752 26685 25741 24882 22822
25150 22604 21870 21035 19310 17043 13521
27612 25349 24701 24032 22511 20907 18781
29370 27282 26674 26066 24696 23254 21708 18049
32062 29480 28382 27585 25914 23719
34092 31897 30843 29919 28420 26637 24050
31598 29657 29143 28577 27407 26078 24712 22298
33591 31765 31309 30796 29731 28536 27286 25299 20153
38013 36203 35539 34594 32996 31652 30072 26691
40393 38690 38264 37449 35716 34451 33186 30778
SBCE/SBCS-3L54-30
SBCE/SBCS-3H54-30
SBCE/SBCS-3L54-50
SBCE/SBCS-3H54-50
SBCE/SBCS-3L54-75
SBCE/SBCS-3H54-75
SBCE/SBCS-3L54-100
3
3
5
37461 35823 35414 35004 34086 33131 32068 30386 27398 22327
39864 38325 37941 37556 36748 35851 34954 33382 30664 27125 21725
43473 41891 41495 41090 39437 38008 36833 34916 30021
5
71⁄2
71⁄2
10
46203 44715 44342 43970 42720 41165 40006 38347 34940
42913 41483 41126 40768 40054 39254 38421 37100 34654 32044 28344
45609 44264 43928 43592 42919 42229 41445 40269 38025 35671 33163 23604
47883 46447 46088 45729 44718 43217 41935 40334 37224 30947
50894 49542 49204 48866 48191 46850 45438 43846 41235 37872
47192 45892 45567 45242 44592 43942 43205 42068 39973 37748 35353 27829
50182 48959 48654 48348 47737 47126 46501 45432 43599 41507 39367 33873
684 10.03 53
727 12.00 61
805 10.02 55
856 12.00 61
SBCE/SBCS-3H54-100 10
Performance certified is for Models SBCE/SBCS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
Numbers in blue have a larger BHP and require the next size larger motor.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
60-72 Belt Drive SBCE/SBCS
Cast Aluminum
Model SBCE for exhaust — Model SBCS for supply
CFM / Static Pressure in Inches WG
0.00 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75 1.00
Motor Fan Max
HP RPM BHP
Model Number
60 Performance
*Sones
Max RPM L - 620 H - 775
Max Motor Frame Size - 254T
TS = RPM x 15.691
310 1.51 16.6 30908 25347 22293 19082
341 2.01 19.4 33999 29312 27467 24664
CFM values shown
in black are the most
efficient selections.
Values shown in gray
are not recommended.
SBCE/SBCS-3L60-20
SBCE/SBCS-3H60-20
2
2
363 2.42
389 1.52
427 2.01
453 2.40
390 3.00
415 3.62
488 3.00
519 3.61
463 5.02
492 6.02
579 5.01
615 6.01
530 7.53
563 9.03
663 7.53
704 9.01
583 10.02
620 12.10
729 10.01
775 12.00
22
21
24
27
25
28
30
32
32
36
38
42
41
46
48
54
50
56
57
63
36192 31785 30693 28420 23150
29943 25920 24798 23553 20680 15870
32868 29286 28268 27248 24967 22058 17552
34870 31476 30591 29632 27574 25189 22147
38884 34776 33760 32638 27839
SBCE/SBCS-3L60-30
SBCE/SBCS-3H60-30
SBCE/SBCS-3L60-50
SBCE/SBCS-3H60-50
SBCE/SBCS-3L60-75
SBCE/SBCS-3H60-75
SBCE/SBCS-3L60-100
3
3
41377 37510 36555 35601 32117 27497
37564 34371 33650 32779 30979 28994 26657 21643
39950 36909 36232 35520 33845 32059 30140 26478
46162 42688 41830 40975 39264 35742 31582
49054 45784 44971 44165 42555 40364 36566 30638
44569 41770 41163 40556 39227 37725 36138 33558 27786
47340 44661 44089 43517 42374 40977 39563 37234 32691 25081
52842 49807 49049 48296 46801 45306 42821 37434
56133 53276 52561 51847 50438 49031 47623 43088 34085
51034 48490 47960 47430 46369 45239 43927 41918 38131 33224
54190 51775 51244 50745 49746 48747 47588 45736 42385 38434 33206
58127 55368 54678 53988 52623 51264 49905 46376 38202
61816 59221 58573 57924 56632 55354 54076 52119 44587
56115 53782 53238 52756 51791 50827 49796 48006 44851 41263 36767
59656 57462 56913 56439 55532 54624 53717 52131 49309 46183 42537 31181
5
5
71⁄2
71⁄2
10
SBCE/SBCS-3H60-100 10
72 Performance
Max RPM L - 578 H - 795
Max Motor Frame Size - 256T
TS = RPM x 18.802
278 2.00 19.3 41857 28605 23878 19635
SBCE/SBCS-3L72-30
SBCE/SBCS-3H72-30
3
3
319 3.03
338 3.60
381 1.99
438 3.02
465 3.58
378 5.04
401 5.71
519 5.02
551 6.00
432 7.52
459 8.69
594 7.56
631 9.00
476 10.06
505 12.00
653 10.00
694 12.00
544 15.00
578 18.00
748 15.00
24
27
28
34
37
33
37
46
52
41
45
58
65
48
54
69
77
63
72
90
48030 37936 33936 29771
50891 41519 38276 34437 26696
40824 35815 34566 33074 29443 24659
46931 42584 41485 40398 37929 34824 31069 23783
49824 45755 44693 43669 41527 39012 35800 29847
56913 48882 46438 43660 36768 29874
60376 53221 50620 48457 42331 35746 29279
55610 52015 51052 50092 48258 46311 44091 39883 30522
59039 55683 54777 53870 52112 50384 48405 44927 37456
65043 58947 56432 54138 49416 43402 37327
SBCE/SBCS-3L72-50
SBCE/SBCS-3H72-50
SBCE/SBCS-3L72-75
SBCE/SBCS-3H72-75
SBCE/SBCS-3L72-100
5
5
71⁄2
71⁄2
10
69109 63324 61492 59114 55204 49816 44056 35555
63646 60574 59733 58892 57219 55616 54013 51160 45205 37157
67611 64754 63963 63171 61587 60049 58540 56106 51062 44626 36346
71668 66060 64634 62341 58348 53680 48216 39954
76035 70697 69477 67767 63628 60117 55073 47224
69968 67229 66464 65699 64169 62660 61202 59001 54465 48597 41207
74361 71806 71103 70384 68944 67504 66111 64053 60168 55291 49391
81907 76884 75751 74618 70920 67400 63833 56750 44689
87026 82239 81173 80107 77299 73547 70545 64621 53266 42050
80147 77777 77176 76508 75172 73836 72500 70580 67340 63488 58637 46264
SBCE/SBCS-3H72-100 10
SBCE/SBCS-3L72-150 15
SBCE/SBCS-3H72-150 15
795 18.00 104 85183 82953 82395 81804 80547 79290 78033 76179 73186 69826 65974 55871
Performance certified is for Models SBCE/SBCS for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
*Sones shown apply to the highest cataloged CFM in black type at each fan RPM. For selections at other CFM and static pressure points, refer to the CAPS
computerized selection program.
Numbers in blue have a larger BHP and require the next size larger motor.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
24-72 Belt Drive SBCR
Reversible (Exhaust and Supply)
CFM / Static Pressure in Inches WG
Motor
HP
Fan
Max
Model Number
Sones
RPM BHP
0.00 0.05 0.10 0.125 0.15 0.20 0.25 0.30 0.375 0.50 0.625 0.75
24 Performance
Max RPM = 1623
Max Motor Frame Size = 145T
14.2 4792 4447 4061 3827 3413
15.0 5088 4766 4411 4216 3961
TS = RPM x 6.283
SBCR-24-4
SBCR-24-4
SBCR-24-3
SBCR-24-5
SBCR-24-7
SBCR-24-10
SBCR-24-15
841
893
983
0.24
0.28
0.39
1/4
1/3
1/2
3/4
1
16.6 5601 5312 5001 4829 4651 4127
19.4 6416 6165 5898 5763 5618 5308 4892 3875
1126 0.59
1288 0.89
1418 1.13
1623 1.77
23
27
35
7339 7119 6893 6774 6656 6406 6135 5807 4756
8080 7880 7680 7572 7465 7249 7015 6769 6313
9248 9074 8899 8812 8719 8531 8343 8148 7825 7171 5560
11⁄2
30 Performance
Max RPM = 1506
Max Motor Frame Size = 184T
15.2 7420 6809 6030 5422
16.1 7889 7323 6622 6141 5545
18.8 9033 8553 8000 7667 7305 6276
TS = RPM x 7.854
SBCR-30-3
SBCR-30-3
SBCR-30-5
SBCR-30-7
SBCR-30-10
SBCR-30-15
SBCR-30-20
SBCR-30-30
681
724
829
949
0.33
0.40
0.60
0.90
1/3
1/2
3/4
1
23
27
32
37
47
10341 9921 9461 9217 8944 8304 7416
11387 11006 10606 10385 10163 9650 9027 8221
1045 1.20
1196 1.78
1316 2.39
1506 3.58
11⁄2
2
13032 12699 12367 12185 11992 11604 11160 10680 9682
14339 14037 13735 13584 13417 13065 12713 12303 11634 10018
16410 16146 15881 15749 15617 15332 15025 14717 14215 13217 11824
3
36 Performance
Max RPM = 1420
Max Motor Frame Size = 184T
16.7 10384 9580 8639 8115 7177
18.1 11037 10299 9409 8967 8440
TS = RPM x 9.424
SBCR-36-5
SBCR-36-5
SBCR-36-7
SBCR-36-10
SBCR-36-15
SBCR-36-20
SBCR-36-30
SBCR-36-50
620
659
755
830
951
0.49
0.57
0.85
1.13
1.79
1/2
3/4
1
22
26
30
35
44
64
12645 12019 11258 10874 10495 9613
13901 13332 12675 12316 11969 11265 10429
15927 15431 14915 14602 14289 13677 13074 12361 10104
17519 17067 16615 16359 16074 15505 14955 14407 13436
11⁄2
2
1046 2.26
1198 3.40
1420 5.75
3
5
20064 19670 19276 19079 18875 18378 17881 17396 16678 15294
23782 23450 23117 22951 22784 22452 22043 21624 20995 19985 18886 17393
42 Performance
Max RPM = 1212
Max Motor Frame Size = 215T
17.2 12939 11634 9951 8604
18.6 13744 12530 11087 10017
TS = RPM x 10.995
SBCR-42-5
SBCR-42-5
SBCR-42-7
SBCR-42-10
SBCR-42-15
SBCR-42-20
SBCR-42-30
SBCR-42-50
530
563
644
709
812
893
0.50
0.60
0.90
1.19
1.80
2.39
1/2
3/4
1
23
26
32
37
48
67
15722 14691 13502 12884 12009
17308 16398 15341 14780 14218 12542
19823 19030 18145 17684 17200 16213 14810 12626
21800 21079 20306 19887 19467 18585 17625 16359 12952
24974 24344 23715 23354 22988 22255 21484 20706 19154
29588 29056 28525 28259 27983 27365 26747 26122 25137 23184 20457
11⁄2
2
3
5
1023 3.59
1212 5.96
48 Performance
Max RPM = 1166
Max Motor Frame Size = 215T
TS = RPM x 12.566
SBCR-48-7
SBCR-48-7
SBCR-48-10
SBCR-48-15
SBCR-48-20
SBCR-48-30
SBCR-48-50
SBCR-48-75
509
541
596
682
750
859
0.74
0.89
1.20
1.79
2.38
3.58
21
22
26
32
37
45
62
83
18042 16152 13446 11755
19176 17432 15068 13528 11927
21126 19601 17641 16402 15002 11943
24174 22893 21309 20403 19418 16986 14441
26584 25419 24052 23305 22476 20552 18308 15990
30448 29431 28350 27706 27062 25649 24004 22085 19067
36083 35225 34367 33934 33390 32303 31152 29930 27688 23511
41329 40580 39831 39457 39082 38184 37235 36278 34678 31491 27851 24113
3/4
1
11⁄2
2
3
5
1018 5.97
1166 8.96
71⁄2
54 Performance
Max RPM = 920
Max Motor Frame Size = 254T
TS = RPM x 14.135
SBCR-54-15
SBCR-54-15
SBCR-54-20
SBCR-54-30
SBCR-54-50
SBCR-54-75
SBCR-54-100
460
489
538
616
730
836
1.43
22
24
27
34
44
56
69
23743 22064 20143 18932 17613
25240 23683 21901 20962 19670 17383
27769 26390 24802 23961 23108 20807 18809
31795 30593 29260 28567 27848 26350 24285 22504
37679 36665 35622 35037 34451 33270 32012 30560 28033
43151 42265 41379 40921 40409 39387 38365 37273 35559 31893 27638
47486 46681 45876 45474 45058 44129 43200 42271 40785 37864 34642 31024
11⁄2
1.78
2.38
3.51
5.72
8.97
2
3
5
71⁄2
10
920 11.90
60 Performance
Max RPM = 811
Max Motor Frame Size = 256T
TS = RPM x 15.691
SBCR-60-20
SBCR-60-20
SBCR-60-30
SBCR-60-50
SBCR-60-75
SBCR-60-100
446
474
543
644
737
1.97
2.39
3.56
5.98
8.96
25
27
34
44
56
69
29819 27584 25099 23718 22220 18365
31691 29584 27337 26059 24741 21272
36304 34455 32649 31594 30479 28197 25170 22150
43057 41498 39960 39199 38438 36561 34662 32715 28612
49275 47912 46554 45889 45224 43877 42233 40590 38048 32357
54222 52984 51746 51134 50530 49321 48049 46555 44314 40222 34832
2
3
5
71⁄2
10
811 11.90
72 Performance
Max RPM = 771
Max Motor Frame Size = 256T
TS = RPM x 18.802
SBCR-72-20
SBCR-72-20
SBCR-72-30
SBCR-72-50
SBCR-72-75
SBCR-72-100
SBCR-72-150
371
394
451
535
612
674 12.00
771 17.90
2.00
26
28
35
47
59
71
94
38286 34158 29734 27617 25593
40659 36985 32714 30490 28675 24224
46542 43988 39709 37916 35972 32605 28738
55210 53296 49520 48026 46562 43398 40355 37687 31512
63156 61483 59068 57107 55633 53073 50315 47451 43930 33516
69554 68035 66516 64788 63007 60429 58104 55580 51763 46218
79564 78236 76908 76244 74957 71843 69602 67569 64378 58868 54239 48179
2
2.39
3.59
5.99
8.97
3
5
71⁄2
10
15
Performance certified is for Model SBCR for installation type A: free inlet, free outlet. Power rating (BHP) does not include transmission losses.
Performance ratings do not include the effects of appurtenances (accessories). *Speed (RPM) shown is nominal. Performance is based on actual speed of test.
The sound ratings shown are loudness values in fan sones at 5 ft (1.5 m) in a hemispherical free field calculated per AMCA Standard 301. Values are for installation
type A: free inlet hemispherical sone levels.
Numbers in blue have a larger BHP and require the next size larger motor.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Drive Specifications
Belt Drive
Belt driven, axial type sidewall fans shall be provided as follows:
Propellers shall be constructed with fabricated steel, fabricated aluminum, or cast aluminum blades and
hubs. Propellers shall be securely attached to fan shafts. All propellers shall be statically and dynamically
balanced to AMCA standard 204-05.
Motors shall be permanently lubricated, heavy duty type, carefully matched to the fan load and furnished at
the specified voltage, phase, and enclosure.
Ground and polished steel fan shafts shall be mounted in permanently lubricated, sealed ball bearing
pillow blocks and coated with an anti-corrosive coating. Bearings shall be selected for a minimum (L10) life
in excess of 100,000 hours (L50 average life of 500,000 hours) at maximum cataloged operating speeds.
Drives shall be sized for a minimum of 150 percent of driven horsepower. Pulleys shall be of the fully
machined cast iron type, keyed and securely attached to wheel and motor shafts. Motor sheaves shall be
adjustable for system balancing.
Drive frame and panel assemblies shall be galvanized steel or painted steel. Drive frames shall be formed
channels and fan panels shall have prepunched mounting holes, formed flanges, and a deep formed inlet
venturi. Drive frames and panels shall be bolted construction or welded construction (level 3 fans only).
The axial exhaust or supply fans shall bear the AMCA Certified Ratings Seals for both sound and air
performance.
Fans shall be Model SBE-1, SBE-2, SBE-3, SBS-1, SBS-2, SBS-3, SBCE and SBCS as manufactured by
Greenheck, Schofield, Wisconsin.
Reversible Belt Drive
Belt driven, axial type sidewall fans shall be provided as follows:
Propellers shall be constructed with cast aluminum blades and hubs. Propellers shall be securely attached
to fan shafts. All propellers shall be statically and dynamically balanced to AMCA standard 204-05.
Motors shall be permanently lubricated, heavy duty type, carefully matched to the fan load and furnished at
the specified voltage, phase, and enclosure.
Ground and polished steel fan shafts shall be mounted in permanently lubricated, sealed ball bearing pillow
blocks, and coated with an anti-corrosive coating. Bearings shall be selected for a minimum (L10) life in
excess of 100,000 hours (L50 average life of 500,000) at maximum cataloged operating speeds. Drives shall
be sized for a minimum of 150 percent of driven horsepower. Pulleys shall be of the fully machined cast
iron type, keyed and securely attached to wheel and motor shafts. Motor sheaves shall be adjustable for
system balancing.
Drive frame and panel assemblies shall be galvanized steel or painted steel. Drive frames shall be formed
channels and fan panels shall have prepunched mounting holes, formed flanges, and a deep formed double
inlet venturi. Drive frames and panels shall be bolted construction or welded construction.
The axial exhaust or supply fans shall be tested in accordance AMCA Standard 301 in both sound and air
performance.
Fans shall be Model SBCR as manufactured by Greenheck, Schofield, Wisconsin.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Drive Specifications
Direct Drive
Direct drive, axial type sidewall fans shall be provided as follows:
Propellers shall be constructed with fabricated steel, fabricated aluminum, or cast
aluminum blades and hubs. A standard square key and set screw or tapered bushing
shall lock the propeller to the motor shaft. All propellers shall be statically and
dynamically balanced to AMCA standard 204-05.
Motors shall be permanently lubricated, heavy duty type, carefully matched to the fan
load and furnished at the specified RPM, voltage, phase, and enclosure.
Motor drive frame assemblies and fan panels shall be galvanized steel or painted steel.
Drive frame assemblies shall be welded wire or formed channels and fan panels shall
have prepunched mounting holes, formed flanges, and a deep formed inlet venturi.
Drive frames and panels shall be bolted construction or welded construction (level 2 &
3 fans only).
The axial exhaust or supply fans shall bear the AMCA Certified Ratings Seals for both
sound and air performance.
Fans shall be Model SE1, SE2, SCE3, SS1, SS2, SCE3 and SCS3 as manufactured by
Greenheck, Schofield, Wisconsin.
Reversible Direct Drive
Direct drive, axial type sidewall fans shall be provided as follows:
Propellers shall be constructed with cast aluminum blades and hubs. A standard square key and
set screw or tapered bushing shall lock the propeller to the motor shaft. All propellers shall be
statically and dynamically balanced.
Motors shall be permanently lubricated, heavy duty type, carefully matched to the fan load and
furnished at the specified RPM, voltage, phase, and enclosure.
Motor drive frame assemblies and fan panels shall be galvanized steel or painted steel. Drive
frame assemblies shall be welded wire or formed channels and fan panels shall have prepunched
mounting holes, formed flanges, and a deep formed double inlet venturi. Drive frames and panels
shall be bolted construction or welded construction.
The axial exhaust or supply fans shall be tested in accordance AMCA Standard 301 in both sound
and air performance.
Fans shall be Model SCR3 as manufactured by Greenheck, Schofield, Wisconsin.
Our Warranty
Greenheck warrants this equipment to be free from defects in material and workmanship for a period
of one year from the purchase date. Any units or parts which prove defective during the warranty
period will be replaced at our option when returned to our factory, transportation prepaid. Motors are
warranted by the motor manufacturer for a period of one year. Should motors furnished by Greenheck
prove defective during this period, they should be returned to the nearest authorized motor service
station. Greenheck will not be responsible for any removal or installation costs.
As a result of our commitment to continuous improvement, Greenheck reserves the right to change
Prepared to Support
specifications without notice.
Green Building Efforts
Sidewall Propeller Rev. 4 December 2007 SP
Copyright © 2007 Greenheck
P.O. Box 410 • Schofield, WI 54476-0410 • Phone (715) 359-6171 • greenheck.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|