• If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this product does not disable your alarm equipment.
• If you have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
US Number is located on the cabinet bottom.
REN Number is located on the cabinet bottom.
Rights of the Telephone Company
Should your equipment cause trouble on y our line which may harm the telephone
network, the telephone company shall, where practicable, notify you that temporary
discontinuance of service may be required. Where prior notice is not practicable and the
circumstances warrant such action, the telephone company may temporarily discontinue
service immediately. In case of such temporary discontinuance, the telephone company
must: (1) promptly notify you of such temporary discontinuance; (2) afford you the
opportunity to correct the situation; and (3) inform you of your right to bring a complaint
to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules
and Regulations.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business
and not inconsistent with FCC Rules and Regulations. If these changes are expected to
affect the use or performance of your telephone equipment, the telephone company
must give you adequate notice, in writing, to allow you to maintain uninterrupted service.
3. Press mute/menu again to save.
NOTE: In case of power failure, the handset may display
UNAVAILABLE when the TALK/CALL BACK button is pressed. You
must then place the handset on the main base for 20 seconds to
reset the unit.
Base Station
Temporary Tone
Introduction
Handset Layout
Model 25922 Series
5.8 GHz Cordless
Handset System
User’s Guide
NOTE: If no name is entered, READY shows in the display.
1. Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and
place your cordless telephone on a level surface, such as a desktop or tabletop, or
you may mount it on the wall.
This feature is useful only if you have pulse (rotary) service. Temporary Tone Dialing
enables pulse (rotary) service phone users to access touch tone services offered by
banks, credit card companies, etc. For example, when you call your bank you may need
to enter your bank account number. Temporarily switching to touch tone mode allows
you to send your number.
CAUTION: When using telephone equipment, there are basic
display
safety instructions that should always be followed. Refer to the
IMPORTANT SAFETY INSTRUCTIONS provided with this product
and save them for future reference.
Local Area Code
TALK/CALL BACK
(button)
1. Press the mute/menu button until AREA CODE - - - shows in the display. - - - is
Pre-dialing
delete (button)
the default.
1. Make sure the phone is OFF (not in TALK mode).
2. Dial a telephone number (the number you dial shows in the display).
IMPORTANT: Because cordless phones operate on electricity, you
should have at least one phone in your home that isn’t cordless, in
case the power in your home goes out.
2
2. Use the touch-tone pad on the handset to enter your three digit area code.
3. Press mute/menu again to save.
1. Dial the telephone number and wait for the line to connect.
CALLER ID-VOLUME (5)
CALLER ID-VOLUME (6)
2. When your call is answered, press the *EXIT/tone button on the handset to
temporarily change from pulse dialing to tone dialing.
(button)
NOTE: If you make a mistake dialing the number, use the delete
button to backspace and erase the wrong number, and enter the
correct number.
(button)
NOTE: If you make a mistake, press the delete button to erase a
wrong number.
Before You Begin
3. Follow the automated instructions to get the information you need.
mem
redial (button)
(memory button)
3. Press the TALK/CALL BACK button on that handset. The number automatically dials
and the call timer starts counting the minutes and seconds in the display.
4. Hang up the handset and the phone automatically returns to pulse (rotary)
dialing mode.
Ringer ON/OFF
Parts Checklist
(for model 25922xx1)
1. Press the mute/menu button until RINGER 41 ON shows in the display.
1 ON is the default.
Make sure your package includes the items shown here.
4. When finished, press the TALK/CALL BACK button again to hang up.
format/trans
(format/transfer
button)
chan
Call Transfer (applicable only with additional
handsets)
NOTE : You may enter up to 32 pre-dial digits.
(channel button)
2. Use the CALLER ID-VOLUME (5or6) button or the touch-tone pad on the handset to
scroll to 1 ON or 2 OFF.
3. Press mute/menu to save.
2. Plug one end of the telephone line cord into the TEL LINE jack at the back of the base
and the other end into a modular jack.
Redial
During an external call, you may transfer the external call to another handset.
Handset battery
pack
Battery compartment
While the phone is ON (in TALK mode), press the redial button to redial the last number
you dialed (up to 32 digits).
1. Press the format/trans button on the originating handset. TRANSFERRING shows in
the display. All registered handsets will be paged.
Base
cover
NOTE: If you turn the ringer off, RINGER OFF shows on the display.
3. Plug the AC power converter into the electrical outlet and the DC connector into the
jack at the back of the base.
#PAUSE/ringer
(button)
*EXIT/tone
(button)
- OR -
Ringer Tone
2. Press the format/trans button or TALK/CALL BACK on receiving handset to answer
call.
4. Place the handset in the base cradle. The charge/in use indicator turns on, verifying
the battery is charging. The unit will take 20 seconds to register and verify its security
code. READY shows in the handset’s display.
While the phone is OFF (in standby mode), press the redial button and then the
TALK/CALL BACK button to redial the last number.
Interference Information
You can choose from 3 ring tones.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference; and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
1. Press the mute/menu button until RINGER TONE 401 shows in the display.
01 is the default.
2. Use the CALLER ID-VOLUME (5or6) button on the handset to select from 01 to 03.
Handset
mute/menu
(button)
NOTE: To cancel the call transfer, you may press *EXIT/tone button
or the format/trans button on the originating handset.
flash/call waiting
(button)
Wall mount bracket
Telephone line cord
AC power adaptor
Flash
NOTE: In case of a power failure, the handsets may display
UNAVAILABLE when the TALK/CALL BACK button is pressed. You
must then place all handsets on the main base cradle for 20
seconds to re-register.
For Model 25922xx2 there will be ONE additional handset, charge cradle, battery pack
and cover than shown above.
Use the flash/call waiting button to activate custom calling services such as call
waiting, which are available through your local phone company.
NOTE: If there is no answer within 2 minutes after transferring
the call, then the handsets will be rung back (callback). If no
handset answers within 30 seconds, then the external call will be
automatically dropped.
3. Press mute/menu to save.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
For Model 25922xx3 there will be TWO additional handsets, charge cradles, battery
packs and covers than shown above.
TIP: Do not use the TALK/CALL BACK button to activate custom
calling services such as call waiting or you’ll hang up the phone.
Base Layout
Tone/Pulse
5. Allow the phone to charge for 16 hours prior to first use. If you don’t properly charge
the phone, battery performance is compromised.
1. Press the mute/menu button until 41 TONE 2 PULSE shows in the display.
1 TONE is the default.
For Model 25922xx4 there will be THREE additional handsets, charge cradles, battery
packs and covers than shown above.
Caller ID (CID)
Channel Button
CAUTION: To reduce risk of personal injury, fire, or damage use
only the 5-2748 (gray) or 5-2749 (black) power adaptor listed in
the user’s guide. This power adaptor is intended to be correctly
orientated in a vertical or floor mount position.
IMPORTANT: In order to use this unit’s Caller ID features, you must
subscribe to either the standard Name/Number Caller ID Service or
Call Waiting Caller ID Service. To know who is calling while you are
on the phone, you must subscribe to Call Waiting Caller ID Service.
2. Use the CALLER ID-VOLUME (5or6) button or the touch-tone pad on the handset to
scroll to 1 TONE or 2 PULSE.
3. Press mute/menu to save.
While talking on the phone, it may be necessary for you to manually change the
channel to improve reception and reduce noise or static on the line. Press and release
the chan button to move to the next clear channel.
Wall plate
Telephone Jack Requirements
Privacy of Communications may not be ensured when using this product.
To use this phone, you need an RJ11C type modular telephone
jack, which might look like the one pictured here, installed in
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television
that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from
that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and Resolve
Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing
Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when
ordering copies.
Wall Mounting
Exit
Modular
your home. If you don’t have a modular jack, call your local
telephone
page (button)
Transfer ON/OFF
This unit receives and displays information transmitted by your local phone company.
This information can include the phone number, date, and time; or the name, phone
number, date, and time.
1. Turn the base over.
Press the *EXIT/tone button to cancel any command you initiated.
charge/in use
(indicator)
phone company to find out how to get one installed.
In order to use the Call Transfer feature (applicable ONLY with additional handsets),
you must have the Transfer ON/OFF set to ON through the menu of the transferring
handset.
Equipment Approval Information
line jack
2. Attach the wall mounting pedestal by first inserting the tabs on the open edge of
the pedestal into the slots on the lower portion of the bottom of the base. Then push
down and snap the pedestal into place.
Page
Your telephone equipment is approved for connection to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
Technical Requirements for Telephone Terminal Equipment published by ACTA.
Installation
Caller ID name
This feature assists in locating a misplaced handset.
1. Press the mute/menu button until TRANSFER 41 OFF shows in the display.
2. Use the CALLER ID-VOLUME (5or6) button or the touch tone pad on the handset
and select 1OFF.
3. Slip the mounting holes (on the back of the base) over the wall plate posts, and slide
the unit down into place. (Wall plate not included.)
Digital Security System
Press the page button on the base. The handset beeps continuously for about 2
minutes until you press the TALK/CALL BACK button on the handset or the page button
on the base.
Installing the Phone
1
Notification to the Local Telephone Company
Caller ID phone number
Caller ID Record Number
Your cordless phone uses a digital security system to protect against false ringing,
unauthorized access, and charges to your phone line.
On the bottom of this equipment is a label indicating, among other information, the
US number and Ringer Equivalence Number (REN) for the equipment. You must, upon
request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number is
called. In most (but not all) areas, the sum of the RENs of all devices connected to one line
should not exceed 5. To be certain of the number of devices you may connect to your line
as determined by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this product.
It is designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
NOTE : If desired, gather the extra telephone line and power adaptor
cord and store inside the wall mounting pedestal.
Installing the Handset Battery
3. Press mute/menu again to save.
NOTE: You may still page the handset when the ringer is off.
INSTALLATION NOTE: Some cordless telephones operate at
frequencies that may cause or receive interference with nearby
TVs, microwave ovens, and VCRs. To minimize or prevent such
interference, the base of the cordless telephone should not be
placed near or on top of a TV, microwave ovens, or VCR. If such
interference continues, move the cordless telephone farther away
from these appliances.
NOTE: You must connect the handset battery before use.
Time
Date
Caller status; NEW or REPEAT
Setup
Default Setting
CAUTION: To reduce the risk of fire or personal injury, use only
the Thomson Inc. approved Nickel-Cadmium (Ni-Cd) battery
model 5-2729 or Nickel-Metal Hydride (Ni-MH) battery model
5-2522, which are compatible with this unit.
Ringer ON/OFF Shortcut
You may return handset settings to the factory default setup using this menu.
There are eight programmable menus available: Language, Handset Name, Area Code,
Ringer On/Off, Ringer Tone, Tone/Pulse, Transfer ON/OFF and Default Setting.
Apart from the setting in the main menu, there is a shortcut to set the ringer. Make sure
Call Waiting Caller ID
1. Press the mute/menu button until DEFAULT 4NO shows in the display. NO is
the default.
the phone is OFF (not in talk mode).
Provided you subscribe to Call Waiting Caller ID service from your phone company; if
you receive an incoming call and you are already on the phone, a beep indicates the
presence of a Call Waiting call on the line. Only the handset that is in use at the time of
the call will display and store the Call Waiting Caller ID information.
During programming, you may press the mute/menu button at any time to go to the
next option. To exit the menu, keep the previous setting and return to the standby
mode, press the *EXIT/tone button.
Notice: The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
1. Press the #PAUSE/ringer button to go to the RINGER ON/OFF menu.
RINGER 41 ON shows in the display. 1 ON is the default.
1. Locate battery and battery door which are packaged together inside a plastic bag
and are separate from the handset.
2. Use the CALLER ID-VOLUME (5or6) button on the handset to scroll to YES or NO.
NOTE: If you choose YES, all settings in the programmable menu
return to the factory defaults.
3. Press mute/menu to save.
Certain other communications devices may also use the 5.8 GHz / 900
MHz frequency for communication, and, if not properly set, these
devices may interfere with each other and/or your new telephone.
If you are concerned with interference, please refer to the owner’s
manual for these devices on how to properly set channels to avoid
interference. Typical devices that may use the 5.8 GHz frequency
for communication include wireless audio/video senders, wireless
computer networks, multi-handset cordless telephone systems, and
some long-range cordless telephone systems.
2. Use the CALLER ID-VOLUME (5or6) button or the touch-tone pad on the handset to
scroll to 1 ON or 2 OFF.
Hearing Aid Compatibility (HAC)
2. Locate the battery compartment on the back of the handset.
Display Language
• When you hear the call waiting beep in the handset receiver, press the flash/
call waiting button to put the current call on hold and answer the incoming call.
Press the flash/call waiting button again to return to the original call.
This telephone system meets FCC standards for Hearing Aid Compatibility.
3. Plug the battery pack cord into the jack inside the compartment. PLEASE REGISTER
shows in the display.
3. Press the #PAUSE/ringer button to save your selection. You will hear a
confirmation tone.
1. Press the mute/menu button until 41ENG 2FRA 3ESP shows in the display. 1ENG is
Licensing
the default. (ENG stands for English. FRA stands for French. ESP stands for Spanish.)
Notes
Cordless Phone Basics
Charge/In Use Indicator
NOTE: To ensure proper battery installation, the connector is keyed
and can be inserted only one way.
• This equipment may not be used on coin service provided by the telephone company.
Licensed under US Patent 6,427,009.
2. Use the CALLER ID-VOLUME (5or6) button or the touch-tone pad on the handset to
enter your selection.
Volume
Receiving CID Records
• Party lines are subject to state tariffs, and therefore, you may not be able to use your
own telephone equipment if you are on a party line. Check with your local telephone
company.
• Notice must be given to the telephone company upon permanent disconnection of your
telephone from your line.
When the phone is ON (in TALK mode) press the CALLER ID-VOLUME (5or6) button to
adjust the listening level. Choose from five volume settings. VOL 1 is the lowest volume
and VOL 5 is the highest volume.
FCC RF Radiation Exposure Statement
When you receive a call, the Caller ID information is transmitted between the first and
second ring. The Caller ID information appears on the display while the phone rings,
giving you a chance to monitor the information and decide whether or not to answer
the call.
The phone is ON when the charge/in use indicator on the base is lit. The handset visual
battery
pack
3. Press mute/menu again to save.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20 centimeters between the radiator and your body. This transmitter must not be co-located
or operated in conjunction with any other antenna or transmitter.”
ringer and base indicator flash when you receive a call.
black wire
Handset Name
Answering a Call
NOTE: The phone will automatically reset VOL 5 to VOL 4 after you
hang up.
Important Installation Guidelines
1. Press the mute/menu button until ENTER NAME shows in the display.
1. When the phone rings, pick up the handset and press the TALK/CALL BACK button.
• Avoid sources of noise and heat, such as motors, fluorescent lighting, microwave
ovens, heating appliances and direct sunlight.
Storing CID Records (In CID Memory)
2. Use the touch-tone pad on the handset to enter the name (up to 15 characters).
More than one letter is stored in each of the number keys. For example, to enter the
name Bill Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the
letter I. Press the 5 key 3 times for the letter L. Wait for one second. Press the 5 key 3
times for the second letter L. Press the 1 key to insert a space between the L and the
S. Press the 7 key 4 times for the letter S; press the 6 key once for the letter M; press
the 4 key 3 times for the letter I; press the 8 key for the letter T; press the 4 key twice
for the letter H..
PRESS DOWN
2. When finished, press the TALK/CALL BACK button again or place the handset on the
base cradle to hang up.
Mute
FIRMLY
If you are not at home or cannot answer, your telephone’s Caller ID memory stores the
data for the 40 most recent calls you received so you can see who called while you
were unavailable. When the 41st call is received, the oldest Caller ID record (1st call) is
automatically deleted.
CAUTION:
RISKOFELECTRICSHOCK
DONOTOPEN
red wire
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
Use mute during a phone conversation to speak privately and off-line with a third party.
Making a Call
1. Press the mute/menu button. MUTE shows in the display. The party on the telephone
will not hear you.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
THE LIGHTNING
CAUTION: TO REDUCE THE
4. Insert the battery pack.
FLASH AND ARROW RISK OF ELECTRIC SHOCK, DO
WARNING:TO
1. Pick up the handset and press the TALK/CALL BACK button. Wait for the dial tone.
The call timer starts counting minutes and seconds in the display.
HEAD WITHIN THE NOT REMOVE COVER (OR
WARNING SIGN
ALERTING YOU OF
IMPORTANT
BACK). NO USER
5. Close the battery compartment by pushing the door up until it snaps into place.
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSETHIS
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
• Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
Thomson Inc.
You may review the stored information at any time. Calls received since your last review
show as NEW in the display. Calls that have not been previously reviewed but were
received from the same number more than once show as REPT in the display.
2. Press the mute/menu button when finished.
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
10330 North Meridian Street
2. Dial a telephone number.
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
Model 25922
00017560 (Rev. 2 Dom E)
07-36
Indianapolis, IN 46290
© 2007 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
• Never touch non-insulated telephone wires or terminals, unless the telephone line
has been disconnected at the network interface.
3. When finished, press the TALK/CALL BACK button again or place the handset on the
base cradle to hang up.
NOTE: If you make a mistake press the delete button to backspace
and erase the wrong character(s) or number(s).
PRODUCT TO RAIN
OR MOISTURE.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
Printed in China
• Use caution when installing or modifying telephone lines.
Download from Www.Somanuals.com. All Manuals Search And Download.
|