ASSEMBLY INSTRUCTIONS
DX-WD1201
Espresso TV Stand for 32" TVs
Download from Www.Somanuals.com. All Manuals Search And Download.
4
DX-WD1201
Package contents
Package contents: hardware
Make sure you have all the hardware necessary to assemble your new TV stand:
Label
Hardware
Qty.
Label
Hardware
Qty.
Rubber
sleeve
Q
4
M2
17
Hidden cam
R
S
13
1
Cam cover
Cam dowel
N2
17
Warning
label
Angle
bracket
O
P
3
6
Metal pin
Label
Hardware
Qty.
T
2
Black1-7/8”flat
head screw
U
V
6
Black 9/16” large
head screw
24
Nail
1
2
3
4in
10
20
30
40
50
60
70
80
90
100mm
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1201
5
Package contents: parts
Note: All parts except for the back (G) have a lettered sticker to make identifying parts easier.
Letter
Description
Right end
Qty. Letter
Description
Qty.
1
1
1
1
1
1
Back
A
B
C
G
H
I
1
1
1
1
1
2
Left end
Upright
Top
Adjustable shelf
Stop molding
Top skirt
D
E
J
Bottom
Shelf
Bottom molding
End molding
K
W
F
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
6
DX-WD1201
Assembly instructions
Step1:
Assemble your stand on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
A hidden cam (M2) has an arrow. When you insert the hidden cam, make sure that the arrow points toward
the hole in the side of the part you are inserting it into.
Push seventeen hidden cams (M2) into the ends (A and B), top (D), bottom (E), and shelf (F). Then, insert the
metal end of a cam dowel (N2) into each hidden cam.
Do not tighten the hidden cams in this step.
Arrow
You’ll need:
M2 (17)
N2 (17)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1201
7
Tightening hidden cams:
In the remaining steps, use these illustrations for instructions on tightening hidden cams.
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not
completely tightened will loosen, and parts may separate.
Arrow
Make sure that you turn the
hidden cam a minimum of
190° to a maximum of 210°.
Note the position of the arrow
on the hidden cam.
Arrow
210°
In the illustration below,
the hidden cam has not
been tightened enough.
190°
You’ll need:
Phillips screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
8
DX-WD1201
Step 2:
Fasten the shelf (F) to the ends (A and B). Use a Phillips screwdriver to tighten four hidden cams (M2). See
Insert two metal pins (P) into the upright (C), then insert the other ends of metal pins (P) into the holes in the
shelf (F).
Notched edge
Finished edge
Notched
edge
Surface with holes
Arrow
210°
190°
You’ll need:
Phillips screwdriver
P (2)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1201
9
Step 3:
Slide the bottom molding (K) onto the notched edge of the bottom (E).
Fasten the bottom (E) to the ends (A and B). Use a Phillips screwdriver to tighten four hidden cams (M2). See
Fasten the bottom (E) to the upright (C). Use a Phillips screwdriver and two black 1-7/8" flat head screws (T).
fi
Surface
with
hidden
cams
US Patent #5,499,886
Holes for screws
Arrow
210°
190°
You’ll need:
T (2)
Phillips screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
10
DX-WD1201
Step 4:
Fasten three angle brackets (O) to the stop molding (I). Use a Phillips screwdriver and three black 9/16" large
head screws (U).
Fasten the stop molding (I) to the top (D). Use a Phillips screwdriver to tighten three hidden cams (M2).
Carefully turn your stand onto its top.
Fasten the ends (A and B) to the top (D). Use a Phillips screwdriver to tighten six hidden cams (M2).
Arrow
210°
190°
Notched edges
You’ll need:
Phillips screwdriver
O (3)
U (3)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1201
11
Step 5:
Slide the end moldings (W) onto the notched edges of the ends (A and B).
Fasten the top skirt (J) to the angle brackets (O) on the stop molding (I). Use a Phillips screwdriver and three
black 9/16" large head screws (U).
Note: There are no pre-drilled holes in the top skirt (J). The screws will tighten into the groove.
You’ll need:
Phillips screwdriver
U (3)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
12
DX-WD1201
Step 6:
Carefully turn your stand over onto its front edges. Unfold the back (G) and lay it over your stand.
Make equal margins along the side and bottom edges of the back (G). Push on opposite corners of your stand
if needed to make it “square.”
Fasten the back (G) to your stand using the nails (V).
Note: Make sure that you tap nails into the holes that line up over the upright (C) and shelf (F).
Note: Perforations have been provided for access through the back (G). Carefully cut out the holes needed.
Caution: Do not
These holes must line up over the
back edges on the upright (C) and
shelf (F).
stand your stand
upright without the
back fastened. Your
stand may collapse.
Do not tap
nails in this
edge
You’ll need:
Hammer
V (24)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1201
13
Step 7:
Carefully stand your stand upright.
Push the rubber sleeves (Q) over the remaining metal pins (P). Insert the metal pins (P) into the hole locations
of your choice in the right end (A) and upright (C). Set the adjustable shelf (H) onto the metal pins (P).
Apply the warning label (S) to the top (D). You should be able to read the label when the TV is removed from
your stand. When the TV is in place, it should hide the label. Peel off the backing and apply the label as
shown.
Caution: This is a permanent label intended to last for the life of the product. Once applied, do not try to
remove it. You may damage the finish on the top.
Push a cam cover (R) onto each visible hidden cam (M2).
Clean with your favorite furniture polish or a damp cloth. Wipe dry. Your stand is ready to use.
Warning: Never use this furniture with a TV
that is too large or too heavy. Severe injury
or death can occur. The TV and furniture
will be unstable and may tip.
•
•
The TV must weigh less than 95 lbs.
The base of the TV must be able to sit
completely on this shelf.
P and Q
You’ll need:
P (4)
Q (4)
R (13)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
14
DX-WD1201
Still need help?
For customer service, call: 800-305-2204 (U.S./Canada markets)
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
© 2012 BBY Solutions, Inc.
All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other
products and brand names are trademarks of their respective owners.
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1201
15
This page intentionally left blank.
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
Certificate of Conformity
1. This certificate applies to the Sauder
Woodworking Product identified by this
instruction booklet.
2. This certificate applies to the compliance of this
product with the CPSC Ban on Lead-Containing
Paint (16 CFR 1303).
3. This product was manufactured by:
Sauder Woodworking Company
502 Middle Street
Archbold, Ohio 43502
(419) 446-2711
4. Date of Manufacture: _________________
Lot number: 345973
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2012 BBY Solutions, Inc.
All rights reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
brand names are trademarks of their respective owners.
12-0782
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
|