1U03 2384
Range Hood
Model: BUF-01A/02A INSTALLATION MANUAL
NAMES OF PARTS
CIRCUIT DIAGRAM
SAFETY INSTRUCTIONS
Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire ProtectionAssociation
(NFPA), and The American Society for Heating,
Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
Motor
Fan Switch
Enclosure
Connector
Switch
Pilot Lamp
Connector
Grey
Yellow
Yellow
Black
Yellow
Red
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the
outdoors.
e) This unit is designed for ducted or ductless
installation. When ductless kit part numbers
FDK-02A is installed, this unit is certified ductless.
The end user is responsible to ensure compliance
with all Federal, State and Local Environmental
and Fire codes.
Connector
WARNING indicates a potentially
WARNING:
hazardous situation which, if not
avoided, could result in death or
serious injury.
White
Red
Connector
White
Black
Connector
Front cover
Lamp:50W
Black
White
White
White
120V
60Hz
CAUTION:
CAUTION indicates a potentially
Lamp
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
(standard MR16-GU10, 50Watt)
(not supplied)
Filter
Green
Capacitor
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
5. This unit must be grounded.
ACCESSORIES
RANGE HOOD LOCATION
NOTE: The safety instructions are explained with the following
6. Check that the hood is correctly installed, since
incorrect installation could result in the range hood
becoming detached and falling off.
pictographic symbols.
The range hood must be installed just above the cooktop.
1
2
Screw M5×30
Four (4) pieces
Nut with plate
Four (4) pieces
The minimum distance from the cooking surface to the bottom of the
range hood must be 24".
means prohibition. It indicates actions, if any,
that mustn’t be done.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
means forcible execution. It indicates actions, if
any, that must be done.
DIMENSIONS
CAUTION
18-11/16"
(Unit: inch)
5-3/16"
WARNING
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls or ceilings or into attics,
crawl spaces, or garages.
6-11/16"
4-1/4"
Holes for mounting range hood
3. Read specification label on this product for further
information and requirements.
17-1/4"
5-7/8"
The total weight of the BUF-01A/02A range hood unit is 18 lbs. (8 kg)
4. Use only for the purpose of kitchen ventilation.
3
4
Power requirements are:
BUF-01A: AC120 V, 60 Hz, 1.5 Amp
BUF-02A: AC120 V, 60 Hz, 2.1 Amp
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
19-11/16"
4-15/16"
WARNING:
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.
• Check that the hood is correctly installed, since incorrect installation
could result in the detachment of the range hood and the unit could fall.
CAUTION:
7. Keep your hands and other objects away from
the fan while it is in motion. The range hood may
injure you or damage itself.
• To protect hands from injury, wear working gloves when installing the
range hood.
INSTALLATION
Make the duct joint secure and air tight using non-flammable
tape such as duct tape, etc. (not supplied)
(5) Remove 4 screws to detach the front cover.
Then, turn it over and remove 2 cushions of foamed
polystyrene put on its both ends.
1. Preparation
4. Final Assembly and Check
3
Assembly
Note: Make sure that the shutter installed in the exhaust pipe
1
WARNING:
• If the range hood is not installed properly, it could become detached
and fall.
• Ensure that the metal duct does not touch other metal housing
materials, otherwise fire or electric shock could result.
moves freely.
Front cover
(1) Replace the front cover with 4 screws.
To prevent the screw holes from being damaged, be sure
not to over tighten the screws (with the torque of 13 inch-lbs.
[1.5 N-m] or less).
Cushion
Roof cap
According to the conditions where
the range hood is installed,
determine whether it will be
1
6" round duct
(For vertical
discharge)
(2) One 50Watt halogen light bulb (not supplied) can be mounted
in this range hood.
Prior to function check, install light bulb (Bulb type standard
MR16-GU10), rated 120V - 50Watt or below.
discharged vertically or horizontally
(6" Round duct). For vertical or
horizontal discharge, run duct work
between the hood location and the
roof cap or wall cap. For best result
in either direction, use a minimum
number of transitions and elbows.
Be sure to attach a roof cap or wall
cap to avoid rain/wind entry.
The following light bulbs are recommended for this range
hood.
• GE Model No. Q50GU10/FL/CD
Soffit
Wall cap
• PHILIPS Model No. Twistline 50W GU10 120V MR16
3. Connecting Power Supply Wires
6" round duct
(For horizontal
discharge)
Turn the lamp clock-wise to install.
Range hood
WARNING:
• Remove the cushions without fail, otherwise there is a risk of fire.
WARNING:
The range hood unit must be mounted to a liner which has the
following dimensions. Install the liner securely after checking that
the opening size of the liner is the same as the figure below.
2
Note: When installing
the bulb, be sure
to fix to the socket
securely.
• Electrical wiring should be done by a qualified person(s) in
accordance with all applicable codes and standards, including
fire-rated construction. An unqualified person doing the work could
result in fire, electric shock or injury.
• This range hood uses 120V AC. Do not connect to other voltage
since fire, electric shock or damage could result.
Front
Liner Dimensions (Unit: inch)
2. Range Hood Mounting
18-11/16"
17-1/2"
Liner
Remove the nut (not supplied) from
the conduit connector at the end of
power wiring.
CAUTION:
• Wear working gloves to avoid injury.
1
4-∅1/4"
Holes for mounting range hood
Lamp
Front cover
Center line
Hold up the range hood and insert it into the opening of the liner.
When the 4 securing plates on both sides have passed through
the top of the liner, turn them outward to secure the range hood
on the liner temporarily. Make sure the top of the exhaust pipe is
inserted into the bottom of the duct.
Range hood cutout
1
Push the lamp,
and turn it
WARNING:
Be sure to switch power OFF at service panel before wiring.
Lamp
clock-wise.
(standard MR16-GU10, 50Watt)
(not supplied)
CAUTION:
• The liner shape illustrated in this installation manual is only for
reference.
Connect the conduit through the connecting hole of the enclosure
using the nut previously removed.
2
Check
2
Duct
(1) Turn on the electrical circuit to the range hood.
Duct
(2) Make sure that the switch and light operate correctly.
Refer to page 5 of the Operation Manual.
Securing plate
[each side
two (2) places]
CAUTION:
• When the liner is installed in the wooden hood, the inside of the
wooden hood placed above the cooking surface must be fully
covered by the metal barrier including bottom edges. Select a
suitable liner and metal barrier according to the size and shape of
the wooden hood and install properly.
• The liner should be installed tightly. If the liner installation is not
correct, the range hood unit may become detached and fall.
Conduit
(3) Make sure that the range hood has no abnormal noises and/
or vibration.
Range hood unit
Liner
Liner
Securing
plate
Liner
Run house wiring between service panel and hood location.
3
4
Tape
Prepare the range hood unit.
Exhaust pipe
Securing plate turns
while passing through
the opening of Liner
Detach
the tape
(1) The range hood is supplied
Range hood unit
with the exhaust pipe fixed
on its top plate.
Push to turn ON
(2) Detach the tape stuck on
the exhaust pipe.
Align 4 screw holes of the liner and range hood unit, then fix
securely using the supplied screws and nuts.
2
CAUTION:
(3) Arrange the ends of
6" round duct and
Connect the electrical wires as follows:
Connect wires tightly and securely using wire connectors
(not supplied).
3
• To reduce the risk of injury, keep your hands and other objects
away from the fan while it is in motion.
• Wear working gloves to avoid injury.
Note: Fasten all the screws and nuts evenly.
wiring conduit so that
they can connect
with the top of the
5-7/8"
• Black to Black • White to White • Green to Green
Nut with plate
Nut with plate
[Right & left,
Each two (2) places]
range hood.
Range hood unit
Liner
5-3/16"
5. Explanation to the End User
(4) Be sure to keep 1-3/16"
Duct
(1) Referring to the Operation Manual, explain the operation of this
range hood to end users.
(2) The Installation Manual and Operation Manual should be given to
the end user.
overlapping length of the
pipe and duct.
Four (4) screws
1-3/16"
Range hood
unit
Liner
Download from Www.Somanuals.com. All Manuals Search And Download.
|