Giant Coffeemaker p46w User Manual

Triplex Ceramic  
Plunger Pump  
OperatingInstructions/  
Repair and Service  
Manual  
Models  
P46W, P46W-HK & P46HT  
Contents:  
InstallationInstructions: page 2  
Pump Specifications:  
Kits/TorqueSpecs:  
PumpMountingSelection  
Guide:  
Exploded View:  
Parts List:  
TroubleShooting:  
Recommended Spare  
Parts List:  
page 3-4  
page 5  
page 5  
page 6  
page 7  
page 8  
page 8  
RepairInstructions:  
Dimensions:  
WarrantyInformation:  
page 9-11  
back page  
back page  
Updated 3/02  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model P46W/P46W-HK  
Volume ........................................................................................................ Up to 3.9 GPM  
Discharge Pressure .................................................................................... 2200 PSI  
Inlet Pressure.............................................................................................. -4.35 - 140 psi  
Maximum Crankshaft Rotation Speed ........................................................ Up to 1420 RPM  
Stroke.......................................................................................................... 14.1mm  
Crankcase Oil Capacity .............................................................................. 8 fl. oz.  
Temperature of Pumped Fluids................................................................... Up to 220oF  
Plunger Diameter........................................................................................ 18mm  
Inlet Ports ................................................................................................... (2) 1/2" BSP  
Discharge Ports .......................................................................................... (2) 3/8" BSP  
Pulley Mounting .......................................................................................... Either Side  
Shaft Rotation ................................................................................ Top of pulley towards Head  
Weight ......................................................................................................... 16 lbs.  
Crankshaft Diameter .................................................................................. 18mm  
Volumetric Efficiency @ 1420 .................................................................... 0.96  
Mechanical Efficiency @ 1420 .................................................................. 0.80  
Consult the factory for special requirements that must be met if the pump is  
to operate beyond one or more of the limits specified above.  
PULLEY INFORMATION  
HORSEPOWER INFORMATION  
Pulley selection and pump speed are based on a 1725 Horsepower ratings shown are the power require-  
RPM motor and "B" section belts. When selecting ments for the pump. Gas engine power outputs must  
desired GPM, allow for a ±5% tolerance on pumps be approximately twice the pump power requirements  
output due to variations in pulleys, belts and motors shown above.  
among manufacturers.  
1. Select GPM required, then select appropriate when selecting an electric motor as the power source.  
motor and pump pulley from the same line. To compute specific pump horsepower requirements,  
We recommend that a 1.1 service factor be specified  
2. The desired pressure is achieved by selecting the use the following formula:  
(GPH X PSI) / 1460 = HP  
correct nozzle size that corresponds with the pump  
GPM.  
P46W & P46W-HK PULLEY SELECTION &  
HORSEPOWER REQUIREMENTS  
PUMP MOTOR  
RPM GPM 1000 PSI 1500 PSI 1700 PSI 2200 PSI  
PULLEY PULLEY  
7.75"  
7.75"  
7.75"  
7.75"  
7.75"  
3.55"  
4.25"  
5.25"  
5.95" 1305  
6.45" 1420  
745 2.0  
910 2.5  
1140 3.1  
1.4  
1.7  
2.1  
2.5  
2.7  
2.1  
2.6  
3.2  
3.7  
4.0  
2.3  
2.9  
3.6  
4.2  
4.5  
3.0  
3.8  
4.7  
5.4  
5.9  
3.6  
3.9  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model P46HT  
Volume ........................................................................................................ Up to 123 GPH (2.1 PGM)  
Discharge Pressure .................................................................................... 900 PSI  
Inlet Pressure.............................................................................................. See NPSHR curve below  
Maximum Crankshaft Rotation Speed ........................................................ 900 RPM  
Plunger Diameter........................................................................................ 18mm  
Crankcase Capacity.................................................................................... 8 fl. oz.  
Temperature................................................................................................ Up to 220oF  
Inlet Ports ................................................................................................... (2) 1/2” BSP  
Discharge Ports .......................................................................................... (2) 3/8” BSP  
Pulley Mounting .......................................................................................... Either Side  
Shaft Rotation ............................................................................................. Top of pulley towards head  
Weight ......................................................................................................... 16 lbs.  
Crankshaft .................................................................................................. 18 mm  
23  
20  
16  
13  
10  
6.6  
3.3  
0
200  
400  
600  
800  
1000  
1200  
1400  
1600 1700  
RPM  
NPSHR Chart  
Consult the factory for special requirements that must be met if the pump is  
to operate beyond one or more of the limits specified above.  
PULLEY INFORMATION  
HORSEPOWER INFORMATION  
Pulley selection and pump speed are based on a 1725 RPM Horsepower ratings shown are the power requirements for  
motor and "B" section belts. When selecting desired GPM, the pump. Gas engine power outputs must be approxi-  
allow for a ±5% tolerance on pumps output due to variations mately twice the pump power requirements shown above.  
in pulleys, belts and motors among manufacturers.  
We recommend that a 1.1 service factor be specified when  
1.  
SelectGPMrequired,thenselectappropriatemotorand selecting an electric motor as the power source. To compute  
pump pulley from the same line.  
specific pump horsepower requirements, use the following  
2.  
The desired pressure is achieved by selecting the formula:  
correct nozzle size that corresponds with the pump GPM.  
(GPH X PSI) / 1440 = HP  
P46HT PULLEY SELECTION & HORSEPOWER  
REQUIREMENTS  
PUMP MOTOR  
PULLEY PULLEY  
RPM GPM GPM 200 PSI 400 PSI 600 PSI 900 PSI  
7.75"  
7.75"  
7.75"  
2.0"  
3.25"  
4.25"  
385 0.9 54.0  
676 1.6 96.0  
900 2.1 123  
0.1  
0.2  
0.3  
0.2  
0.4  
0.6  
0.4  
0.7  
0.9  
0.6  
1.0  
1.3  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
P46W, P46W-HK & P46HT REPAIR KITS  
Ceramic Plunger Assembly Kit #09539  
Plunger Packing Kit, P46W #09038  
Item  
24A  
24B  
24C  
25  
Part #  
07021  
08456  
07676  
Description  
Ceramic Plunger  
Tension Screw  
Copper Ring  
Flinger  
Qty.  
3
3
3
3
Item  
31  
40  
Part # Description  
Qty.  
3
07241  
07234  
V-Sleeve  
O-Ring  
3
06648/13333*  
Complete Plunger Packing Kit, P46W #09081  
Item  
31  
40  
50  
51  
Qty.  
3
3
* p/n 13333 is needed for older P46W pumps with brass  
retainers (p/n 08064).  
3
Valve Assembly Kit P46W & P46W-HK #09039  
Item  
34  
Part #  
07325  
Description  
Spring Retainer  
Qty.  
3
3
35  
36  
37  
38  
40  
42  
44  
06017-0100 Valve Spring  
3
3
3
3
3
3
3
Plunger Packing Kit, P46W-HK, P46HT #09514  
06016  
06014  
06015  
07234  
12004  
07035  
Valve Plate  
Valve Seat  
O-Ring, Valve Seat  
O-Ring,Adapter  
O-Ring, Manifold Plug  
O-Ring, Discharge Plug  
Item  
31A  
40  
Part #  
11511  
07234  
11512  
07240  
Description  
Sleeve  
O-Ring,Adapter  
High Temp. Rear Seal  
Support Ring  
Qty.  
3
3
50  
51  
6
3
Valve Assembly Kit, P46HT #09497  
Item  
34  
Part #  
Description  
Qty.  
3
3
06018-0100 Valve Cage  
06017-0100 Valve Spring  
35  
36  
37  
38  
40  
42  
44  
06016  
06014  
06015  
07234  
12004  
07035  
Valve Plate  
Valve Seat  
O-Ring  
O-Ring,Adaptor  
O-Ring, Manifold Plug  
O-Ring, Discharge Plug  
3
3
3
3
3
3
P46W, P46W-HK & P46HT TORQUE SPECIFICATIONS  
Position  
Item#  
08456  
07235  
07034  
08040  
Description  
Torque Amount  
24B  
41  
43  
Tension Screw, Plunger  
Plug, Manifold (Inlet)  
Plug, Manifold (Outlet)  
Hex Nut, Manifold Stud  
105 in-lbs.  
52 ft.-lbs.  
52 ft.-lbs  
35 ft.-lbs  
46  
Pump Mounting Selection Guide  
Bushings  
01065 - 18 mm Tapered H Bushing  
Rails  
01034 - Steel Box Rails  
(L=9.25” x W=1.18” x H=1.62”)  
01075 - Plated Steel Channel Rails  
Pulley & Sheaves  
01061 - 7.75” Cast Iron 1 gr. - AB Section  
01062 - 7.75” Cast Iron - 2 gr. - AB Section  
01066 - 18 mm - 8” Steel Pulley - 1 gr.  
(L=9.00” x W=2.12” x H=2.50”)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Exploded View - P46W, P46W-HK, P46HT  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
P46W, P46W-HK & P46HT PARTS LIST  
ITEM PART  
DESCRIPTION  
Support Ring  
QTY.  
ITEM PART  
DESCRIPTION  
Crankcase  
QTY.  
32  
33  
34  
07231  
07232  
07325  
3
3
1
07222  
07181  
07182  
08004  
08005  
08008  
01009  
07188  
07223  
1
1
1
1
1
1
1
4
Pressure Spring  
Retainer,Spring  
(P46W,&P46HT)  
2
Vent/FillerPlugwithSeal  
Gasket,OilFillerCap  
Cover,Crankcase  
O-Ring  
2A  
3
6
6
6
6
6
6
3
3
3
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
06018-0100 Retainer,Spring(P46HT)  
06017-0100 Valve Spring  
4
5
Oil Dipstick  
06016  
06014  
06015  
07233  
07234  
07235  
12004  
07034  
Valve Plate  
6
O-Ring  
ValveSeat  
9
CylinderScrewwithSlot  
Spring Washer  
(ExcludingP46HT)  
O-Ring  
10  
Suction Valve Adaptor  
O-Ring,Adapter  
Plug Manifold(Inlet)  
4
10  
07223-0100 Spring Washer (P46HTonly) 4  
11  
08012  
06709  
07224  
08015  
08020  
07225  
07226  
07227  
01024  
08024  
07201  
01031  
07021  
08456  
07676  
06648  
07206  
11510  
07207  
07033  
07230  
07241  
11511  
OilDrainPlugwithSeal  
Gasket,OilDrainPlug  
BearingCover  
RadialShaftSeal  
BallBearing  
1
1
2
2
2
6
1
1
1
3
3
3
3
3
3
3
3
3
2
1
3
3
O-Ring,ManifoldPlug(Inlet) 3  
Plug&O-Ring  
11A  
12  
(P46W&P46W-HK)  
Plug&O-Ring(P46HT)  
O-Ringfor43  
3
3
3
2
2
2
1
14  
43  
44  
45  
46  
47  
48  
49  
07792  
07035  
07215  
08040  
08041  
07237  
07238  
15  
16  
Screw and Washer  
Shaft Protector  
Crankshaft  
Stud, Manifold  
17  
Hex Nut, Manifold Stud  
Spring Washer, Stud  
Housing,RearV-Sleeve  
O-Ring,Rear  
18  
19  
Key  
20  
Connecting Rod  
Crosshead Assy.  
Crosshead Pin  
PlungerPipe  
22  
V-SleeveHousing  
1
3
23  
50  
50  
07239  
11512  
RearV-Sleeve(P46Wonly)  
HighTemperatureSeal  
(P46W-HK&P46HT)  
24A  
24B  
24C  
25*  
26  
Tension Screw  
CopperRing  
6
51  
07240  
07109  
07110  
13338  
08486  
SupportRing,RearV-Sleeve 3  
Flinger  
52  
Plug, 1/2" BSP  
Gasket  
1
1
1
RadialShaftSeal  
Spacer Sleeve  
52A  
53  
26A  
28  
Plug, 3/8" BSP  
Copper Crush Washer  
(P46W&P46W-HK)  
Shim, Manifold Stud  
Manifold  
53A  
29  
1
30  
Pressure Ring  
31  
V-Sleeve(P46Wonly)  
V-Sleeve,HighTemp.  
(P46W-HK,P46HT)  
31A  
3
* This will not fit into older P46W pumps with brass retainers (#08064). It can only be used with part number 11510 (#26A).  
You can substitute p/n 13333 for 06648 only if the brass retainer (#08064) is used.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PUMPSYSTEMMALFUNCTION  
MALFUNCTION  
CAUSE  
REMEDY  
The Pressure and/  
or the Delivery  
Drops  
Worn packing seals  
Broken valve spring  
Belt slippage  
Replace packing seals  
Replace spring  
Tighten or Replace belt  
Replacenozzle  
Worn or Damaged nozzle  
Fouled discharge valve  
Fouled inlet strainer  
Worn or Damaged hose  
Worn or Plugged relief valve on pump  
Cavitation  
Clean valve assembly  
Cleanstrainer  
Repair/Replace hose  
Clean, Reset, and Replace worn parts  
Check suction lines on inlet of  
pump for restrictions  
Unloader  
Check for proper operation  
Water in crankcase  
Noisy Operation  
Highhumidity  
Worn seals  
Reduce oil change interval  
Replace seals  
Worn bearings  
oilwith  
Cavitation  
Replacebearings,Refillcrankcase  
recommendedlubricant  
Check inlet lines for restrictions  
and/or proper sizing  
Rough/Pulsating  
Operationwith  
Pressure Drop  
Worn packing  
Inlet restriction  
Replacepacking  
Check system for stoppage, air  
leaks, correctly sized inlet  
plumbing to pump  
Accumulator pressure  
Unloader  
Cavitation  
Recharge/Replaceaccumulator  
Check for proper operation  
Check inlet lines for restrictions  
and/or proper size  
Pump Pressure as  
Rated, Pressure  
Drop at gun  
Restricted discharge plumbing  
Re-size discharge plumbing to  
flow rate of pump  
Excessive  
Leakage  
Worn plungers  
Replace plungers  
Worn packing/seals  
Excessivevacuum  
Cracked plungers  
Inlet pressure too high  
Adjust or Replace packing seals  
Reduce suction vacuum  
Replace plungers  
Reduce inlet pressure  
High Crankcase  
Temperature  
Wrong Grade of oil  
Improper amount of oil in crankcase  
Giant oil is recommended  
Adjust oil level to proper amount  
Preventative Maintenance Check-List & Recommended Spare Parts List  
Check  
Daily  
Weekly  
50hrs  
Every  
500 hrs  
Every  
1500 hrs  
Every  
3000 hrs  
Oil Level/Quality  
Oil Leaks  
Water Leaks  
Belts, Pulley  
Plumbing  
X
X
X
X
X
Recommended Spare Parts  
Oil Change (1 Gallon) p/n 1154  
Plunger Packing Kits (1kit/pump)  
(See page 5 for kit list)  
ValveAssembly Kit (1 kit/pump)  
(See page 5 for kit list)  
X
X
X
X
Oil Seal Kit (1 kit/pump)  
X
(See page 5 for kit list)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR INSTRUCTIONS - P46W, P46W-HK, P46HT  
1. With a 22mm socket, remove the  
three discharge (43) and three  
inlet(41)manifoldplugs.Check  
o-rings (42 & 44) for wear and  
replace as necessary.  
2. Remove the discharge spring  
retainer(34),valvespring(35),  
and valve plate (36).  
3. Use a small slide hammer to  
remove valve seats (37) from  
manifold(29). Inspectvalve  
plates (36) and valve seats (37)  
for wear. If excessive pitting is  
seen, replace the worn parts.  
Check valve seat o-ring (38) for  
wear and replace as necessary.  
4. Drain the oil from the pump.  
Turn the pump over to remove  
the two manifold stud nuts (46)  
witha17mmwrench.  
5. Tap the back of the manifold  
(29) with a rubber mallet to  
dislodge, and slide off the  
pump.  
6. From the front inlet valve ports,  
remove the inlet valve assembly  
(34-40).  
34  
35  
36  
40  
37  
39  
7. Inspect and clean the valve assembly parts. If pitted or worn, replace inlet  
valve seats (37), valve plates (36), spring (35) and spring retainers (34).  
Reinsert items 34-38 into valve adapter (39).  
NOTE: Contact Giant Industries for Service School Information. Phone: (419)-531-4600  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR INSTRUCTIONS - P46W, P46W-HK, & P46HT  
49  
30  
31/50  
31A  
32  
38  
33  
(P46W-HK & P46HT only)  
8. The pressure rings (item 30) can now be removed by pulling straight out.  
Inspect and clean manifold (29) and pressure ring. Replace if necessary.  
From the front of the pump reinstall pressure rings into manifold (29) with  
grooved side towards front of manifold. Install new v-sleeves (31 or 50), with  
grooved sides towards front of pump. For P46W-HK & P46HT pumps, install  
high temperature seal (31A) with grooved sides towards front of pump.  
Replace the support rings (32) and pressure springs (33) into manifold (29).  
Installvalveassembly(34-40)intomanifold(29). Reinstallmanifoldplugs  
(43) and torque plugs to 52 ft.-lbs.  
50  
51  
9. The rear V-sleeve housing (48)  
may be removed by prying  
evenly outward with a flat  
screwdriver. After slipping  
housing over plunger, inspect  
seals (50) and O-ring (49) and  
replace as necessary.  
24C  
10. Inspect ceramic plunger (24A)  
tips for wear. If necessary,  
replacement of the ceramic  
plungers may be accomplished  
by removing the plunger bolt  
assemblies (24B and 24C) with a  
13mmwrench. Ceramic  
11. Replace copper ring (24C) onto  
plungerbolt(24B). Slide  
13. Beforereplacingpumpmanifold  
(29), firstrotatecrankshaft(18)  
until two outside plungers (24A)  
extend evenly forward. Next  
plunger bolt assembly into  
ceramic plunger (24A). Apply a  
light film of loc-tite to plunger  
bolt threads and place plunger  
assembly onto stainless steel  
plunger base (22) and tighten to  
105in.-lbs.  
lubricate v-sleeves (50) in the rear  
v-sleeve housing (48) and slide  
housing over plungers. Lubricate  
ceramic plungers with a light film  
of oil. Carefully and evenly slide  
manifold over plungers and press  
manifoldfirmlyagainstcrankcase  
(1). Replace manifold stud bolts  
(45), washers (47) and nut (46) and  
tighten to 35 ft.-lbs.  
plungers should now slide off  
the stainless steel plunger base  
(22). Excessive resistance to  
plunger removal may be  
12. To replace plunger oil seals  
(26), proceed to “Gear End  
Disassembly” section below.  
Otherwise, continue as de-  
scribed below.  
overcome by heating the  
stainless steel plunger base.  
This will melt any excess loc-tite  
beneath the ceramic plunger  
allowingeasyremoval.  
NOTE: Contact Giant Industries for Service School Information. Phone: (419)-531-4600  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR INSTRUCTIONS - P46W, P46W-HK, & P46HT  
GearEndDisassembly  
14. Remove the crankcase cover bolts (9). Inspect the crancase cover O-ring (4) for wear. Replace if necessary.  
15. Inspect the dip stick (5) vent hole for signs of clogging. Clean if necessary.  
16. To remove the crankshaft (18), first remove the bearing cover plates (12) Remove the key (19).  
17. Hold the pump rear assembly with a wooden fixture, or other suitable device, in order to secure it while removing the  
crankshaft (18). Using a plastic mallet, tap the crankshaft (18) from one side while turning it from the other side. The  
turning insures that during this sequence the crankshaft does not become wedged agaisnt the connecting rods (20).  
The far side bearing (15) will remain in the crancase (1). When free, the crankshaft (18) can be removed by hand.  
18. The crankshaft bearing (15) remains on the crankshaft (18) as it is removed. The near side crankshaft seal (14) will be  
removed by this procedure.  
19. If necessary, use a bearing puller to remove crankshaft bearing (15).  
20. Remove the connecting rod (20) and plunger rod/crosshead assembly (22) from the rear of the pump by pulling  
straight out of the crosshead guides.  
21. To remove the crankcase oil seal (26), tap oil seal out from the rear of the crankcase using a dowel and rubber mallet.  
The area onto which the oil seal rests should be clean and dry. Put a small drop of loc-tite on the oil seals and place  
into crankcase with clips facing the rear of the pump.  
22. To remove the crosshead pin (23) from the crosshead (22), the assembly should be positioned on a wooden fixture to  
avoid damage to crosshead. Drive out pin (23) on opposite side of mark on the crosshead. On those pumps without  
mark on crosshead, drive out pin by tapping on tappered side of pin.  
23. To remove the bearing remaining in the crankcase, insert small end of Giant Bearing tool and tap with a rubber mallet  
untill bearing and seal are completely removed. The bearing can only be removed from the inside by inserting the Giant  
Bearing Tool through the opposite side of the crankcase (1) and should be inspected for possible damage.  
GearEndReassembly  
24. To reassemble, place the far bearing in the crankcase bearing housing and with the Giant Bearing tool as a driver, tap  
into the crankcase (1) using a rubber mallet.  
25. Insert the far side crankshaft oil seal (14) with the Giant Bearing Tool making sure it is firmly seated and well oiled.  
Always make sure that the crankshaft seal (14) lip does not show signs of wear. Replace the bearing cover (12) and  
tighten securely.  
26. Replace the connecting rod (20) and plunger rod/crosshead assembly (22) by press-fitting the crosshead pin (23).  
Make sure to insert the beveled edge of the crosshead pin into crosshead. If the crosshead has a mark, install pin  
frommarked side. The crosshead pin (23) should not extend beyond either side of the crosshead in order to prevent  
damage to the crosshead bore of the crankcase.  
27. Place each crosshead/plunger assembly (22) into the pump making sure that all of the parts are well oiled before  
insertion into the crankcase.  
28. Replace near side bearing on crankshaft (18) and mallet to tap into place.  
29. Take the crankshaft (18) end with the bearing and insert the other end through the bearing housing carefully threading  
the lobes of the crankshaft through the well lubricated connecting rods (20). Turning the crankshaft while tapping it  
through the connecting rods will help prevent binding and possiable damage to the connecting rods. Continue  
tapping the crankshaft through the connecting rods (20) until it is firmly seated into far side bearing.  
30. Insert the near side crankshaft oil seal (14), making sure it is firmly seated and well oiled. Replace the bearing cover (12)  
and tighten securely.  
31. See instructions (13 above) for re-installing fluid end onto gear end.  
32. Clean the back edge of crankcase and replace the crankcase cover. Be careful not to pinch the crankcase cover o-ring.  
33. Fill the P46W crankcase with 8 oz. of Giant oil. and check the oil level with the dipstick. Proper level is center of two  
lines Reinstall the pump into your system.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P46W, P46W-HK & P46HT DIMENSIONS  
GIANTINDUSTRIESLIMITEDWARRANTY  
Giant Industries, Inc. pumps and accessories are warranted by the manufacturer to be free from  
defects in workmanship and material as follows:  
1. For portable pressure washers and car wash applications, the discharge manifolds  
will  
pump  
never fail, period. If they ever fail, we will replace them free of charge. Our other  
parts, used in portable pressure washers and in car wash applications, are  
for five years from the date of shipment for all pumps used in NON-  
clean  
warranted  
SALINE,  
water applications.  
2. One (1) year from the date of shipment for all other Giant industrial and consumer  
pumps.  
3. Six (6) months from the date of shipment for all rebuilt pumps.  
4. Ninety (90) days from the date of shipment for all Giant accessories.  
This warranty is limited to repair or replacement of pumps and accessories of which the  
manufacturer’s evaluation shows were defective at the time of shipment by the manufacturer. The  
following items are NOT covered or will void the warranty:  
1. Defects caused by negligence or fault of the buyer or third party.  
2. Normal wear and tear to standard wear parts.  
3. Use of repair parts other than those manufactured or authorized by Giant.  
4. Improper use of the product as a component part.  
5. Changes or modifications made by the customer or third party.  
6. The operation of pumps and or accessories exceeding the specifications set forth  
in the Operations Manuals provided by Giant Industries, Inc.  
Liability under this warranty is on all non-wear parts and limited to the replacement or repair of those  
products returned freight prepaid to Giant Industries which are deemed to be defective due to  
workmanship or failure of material. A Returned Goods Authorization (R.G.A.) number and  
completed warranty evaluation form is required prior to the return to Giant Industries of all products  
under warranty consideration. Call (419)-531-4600 or fax (419)-531-6836 to obtain an R.G.A.  
number.  
Repair or replacement of defective products as provided is the sole and exclusive remedy provided  
hereunder and the MANUFACTURER SHALL NOT BE LIABLE FOR FURTHER LOSS, DAMAGES,  
OR EXPENSES, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES DIRECTLY OR  
INDIRECTLY ARISING FROM THE SALE OR USE OF THIS PRODUCT.  
THE LIMITED WARRANTY SET FORTH HEREIN IS IN LIEU OF ALL OTHER WARRANTIES OR  
REPRESENTATION,EXPRESSORIMPLIED,INCLUDINGWITHOUTLIMITATIONANYWARRAN-  
TIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ALL SUCH  
WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED BY THE MANUFACTURER.  
3/02 P46W, P46W-HK,  
&
P46HT  
&
P46HT.PM6  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Dyson Vacuum Cleaner DC 14 User Manual
Eicon Networks Network Card D 120JCT LSU User Manual
FieldServer Computer Drive FCI 7100 Series User Manual
FINIS MP3 Player 1G User Manual
Friedrich Air Conditioner CP05 User Manual
Frigidaire Microwave Oven 316495062 User Manual
Garland Oven RBA 24 User Manual
GE Oven JKP30BM User Manual
Gitzo Camcorder Accessories GT2942 User Manual
Gitzo Camcorder Accessories GT3540 User Manual