Fisher Price Swing Sets H4792 User Manual

Product features and decorations may vary from picture above.  
Instructions  
Model Number: H4792  
WARNING  
IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE.  
Please read these instructions before use of this product.  
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).  
Requires four LR20 ("D") alkaline batteries (not included) for operation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if  
any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts.  
Hubs  
CAUTION  
This package contains small parts  
in its unassembled state.  
Adult assembly is required.  
Leg  
Housing  
Back Base  
Button  
Front Curved Base  
2
• Place the front curved base on a flat surface so that it curves  
away from you.  
• Place the back base on a flat surface, behind the front  
curved base.  
Position the leg assemblies so that the hubs are facing  
each other.  
Fit the ends of the legs over the ends of the front and back  
bases, as shown.  
Leg  
Hint: You may need the help of another adult to help you balance  
the assembly.  
1
• Place a housing on a flat surface.  
• Insert the button end of a leg into the hole in the housing.  
• Push the leg in until it “snaps” into the housing.  
Repeat this procedure to assemble the other leg to the  
other housing.  
• Pull the legs to be sure they are secure in the housings.  
If you can remove them, you have not assembled them  
correctly. Please re-read and repeat this assembly step.  
• Pull the other leg back until it “snaps” into place in the housing.  
Repeat this procedure to “snap” the leg in the other housing  
into place.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
CORRECT  
INCORRECT  
HUBS FACING OUT  
HUBS FACING IN  
FRONT  
BASE  
CURVES  
INWARD  
FRONT  
BASE  
CURVES  
OUT  
3
Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above.  
• If the leg assemblies are assembled incorrectly to the bases, simply pull the legs from the bases. Please re-read and repeat  
assembly step 2.  
• Set the frame assembly aside.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Armrest Holes  
Oval End  
Seat Tube  
Round End  
Seat Tube  
Round  
Seat Bottom  
4
6
Position the seat bottom so that the back faces you and the  
armrest holes are facing up.  
Seat Bottom  
Oval  
Locate the round end seat tube.  
Hint: Look at opening in the straight end of the tube. It should be  
completely round.  
Fit the round end seat tube into the round hole in the  
seat bottom.  
Locate the oval end seat tube.  
Hint: Look at opening in the straight end of the tube. It should be oval.  
Fit the oval end seat tube into the oval opening in the  
seat bottom.  
3.8 cm Pin Screw  
3.8 cm Pin Screw  
7
SIDE VIEW  
SIDE VIEW  
5
Align the hole in the seat tube with the hole in the armrest.  
• Insert a 3.8 cm pin screw through the armrest and into the  
seat tube. Tighten the screw.  
Align the hole in the seat tube with the hole in the armrest.  
• Insert a 3.8 cm pin screw through the armrest and into the  
seat tube. Tighten the screw.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Seat Back  
Raised Slots  
Seat Back Wire  
Seat Bottom  
8
Fit the seat back to the seat bottom.  
#8 x 1.9 cm Screw  
10  
Fit the seat back wire through the raised slots on the seat back.  
Rod  
9
• Insert the rod into the side opening between the seat back  
and seat bottom.  
• Insert a #8 x 1.9 cm screw into the opening in the rod  
and tighten.  
11  
Fit the ends of the seat back wire into the outside holes in  
the seat tubes.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Hubs  
Seat Tubes  
Assembly  
Tool  
13  
• Insert the ends of the seat tubes into the holes in the hubs.  
• Push the seat tubes in until you hear a “snap” (for each).  
Rounded Side  
• Push down on the seat to be sure the seat is secured in both  
frame hubs.  
Lock Nut – 2  
12  
Attach a lock nut, rounded side facing out, onto one end of a  
seat back wire.  
#6 x 3.18 cm Screw – 2  
Tighten the lock nut by using the assembly tool. Turn the tool  
clockwise to tighten the lock nut.  
Repeat this procedure to attach the other lock nut to the other  
end of the seat back wire.  
• Please throw the assembly tool away after completing this  
assembly step.  
14  
• Insert a #6 x 3.18 cm screw into each frame hub and tighten.  
Again, push down on the seat to be sure the seat is secured to  
both frame hubs.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Elastic Loops  
Waist Belts  
16  
Holes  
• Insert the waist belts through the slots in the pad.  
Fit the top of the pad over the seat back edge.  
Elastic Loops  
Tabs  
15  
• Place the pad onto the seat.  
• Insert the pad elastic loops through the holes in the  
seat bottom.  
From under the seat, fit the elastic loops onto the tabs  
on the seat back.  
Tabs  
17  
From behind the seat, fit the pad elastic loops to the tabs on  
the seat back.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Slot  
#8 x 1.9 cm Screw – 2  
Toy Bar Hubs  
Crotch Belt  
Clips  
Seat Tubes  
19  
Fit the toybar hubs to the seat tubes.  
Hint: The toybar hubs are designed to fit to the seat tubes one way. If the  
toybar hubs do not fit correctly, turn the toybar around and try again.  
• Insert a #8 x 1.9 cm screw through the seat tubes and into the  
toybar hubs. Tighten the screws.  
Elastic Loops  
18  
Fit the crotch belt through the slot in the pad.  
Fit the pad side clips around the edge of the seat bottom.  
Fit the pad elastic loops around the front edge of the  
seat bottom. Attach the pad elastic loops to the tabs  
underneath the seat bottom.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Tray  
Tray Links  
20  
Fit and “snap” the tray onto the seat armrests.  
• Insert and “snap” the tray links into the holes in the tray.  
21  
Fit the toy links and/or toys on the toy bar/tray!  
Assembly is now complete.  
Download from Www.Somanuals.co1m0. All Manuals Search And Download.  
Battery Installation  
Hint: We recommend using alkaline batteries for longer battery life.  
1,5V x 4  
D(LR20)  
Shown Actual Size  
Battery Safety Information  
Battery Compartment  
Batteries may leak fluids that can cause a chemical burn injury  
or ruin your product. To avoid battery leakage:  
Do not mix old and new batteries or batteries of different  
types: alkaline, standard (carbon-zinc) or rechargeable  
(nickel-cadmium).  
• Insert batteries as indicated inside the battery compartment.  
Remove batteries during long periods of non-use. Always  
remove exhausted batteries from the product. Dispose of  
batteries safely. Do not dispose of batteries in a fire.  
The batteries may explode or leak.  
Never short-circuit the battery terminals.  
Use only batteries of the same or equivalent type  
as recommended.  
Do not charge non-rechargeable batteries.  
Remove rechargeable batteries from the product  
before charging.  
• If removable, rechargeable batteries are used, they are  
only to be charged under adult supervision.  
Loosen the screws in the battery compartment door and  
remove the battery compartment door.  
• Insert four D” (LR20) alkaline batteries into the  
battery compartment.  
Replace the battery compartment door and tighten the screws.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and Use  
IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any  
parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts.  
Waist Belts  
WARNING  
To prevent serious injury or death  
from falls and being strangled in  
the restraint system:  
Crotch Belt  
• Always use the restraint system.  
Never rely on the tray to restrain child.  
• Never use with an active child who  
1
may be able to climb out of the seat.  
Securing your Infant  
• Not recommended for children who  
can sit up by themselves (6 months  
approximately, until 9 kg (20 lbs).  
• Place your child in the seat. Position the crotch belt between  
your childs legs.  
Fasten the waist belts to the crotch belt. Make sure you hear  
a “click” on both sides.  
• Never leave the child unattended.  
• It is dangerous to use this product  
on an elevated surface.  
Check to be sure the restraint system is securely attached by  
pulling it away from your child. The restraint system should  
remain attached.  
Anchored End  
Anchored End  
Free End  
Free End  
TIGHTEN  
LOOSEN  
2
To tighten the waist straps:  
Feed the anchored end of the waist belt up through the buckle  
to form a loop . Pull the free end of the waist belt .  
To loosen the waist straps:  
Feed the free end of the waist belt up through the buckle to  
form a loop . Enlarge the loop by pulling on the end of the  
loop toward the buckle. Pull the anchored end of the waist belt  
to shorten the free end of the waist belt .  
Download from Www.Somanuals.co1m2. All Manuals Search And Download.  
Setup and Use  
Music Button  
Power Switch  
Seat Wire  
4
3
Swinging  
Make sure your child is properly secured in the seat.  
• Slide the swing power switch on to any of six speed settings.  
Watch the toys move when the seat swings!  
Be sure to slide the switch to the off position when the  
swing is not in use.  
Hint: As with most battery-powered swings, a heavier child will reduce  
the amount of swinging motion on all settings. In most cases, the low  
setting works best for a smaller child while the high setting works best  
for a larger child.  
UPRIGHT  
SEMI-RECLINE  
RECLINE  
Adjust the seat angle to any of three positions: Upright,  
Semi-Recline or Recline. To adjust the seat angle:  
Lift or lower the seat wire into the grooves on the seat back.  
Music  
• Push the music button once for music with low volume.  
• Push the music button again for music with high volume.  
• Push the music button a third time to turn music off.  
Note: Low battery power may cause product movement to slow  
and sound volume to become faint or turn off all together.  
If this should happen, please remove and discard all four  
batteries and replace with four, new D” alkaline batteries.  
Download from Www.Somanuals.co1m3. All Manuals Search And Download.  
Setup and Use  
Care  
The pad is machine washable. Wash it separately in cold water  
on the gentle cycle. Do not use bleach. Line dry only.  
The frame, links, toys and toy bar may be wiped clean using a  
mild cleaning solution and a damp cloth. Do not use bleach.  
Do not use harsh or abrasive cleaners. Rinse clean with water  
to remove residue.  
Toy Bar  
Elastic Loops  
1
To remove the pad:  
Remove the four pad elastic loops from the seat back and  
bottom tabs.  
Remove the top of the pad from the seat.  
5
Using the Toy Bar  
Lift or lower the toy bar for babys enjoyment.  
Hint: The toys move when the swing is turned on!  
Waist and  
Crotch Belts  
2
Clips  
Unhook the pad clips from the sides of the seat.  
Remove the pad elastic loops from the front edge of the  
seat bottom.  
• Push the waist and crotch belts back through the pad slots.  
Remove the pad from the seat.  
To replace the pad, refer to Assembly steps 15-18.  
Download from Www.Somanuals.co1m4. All Manuals Search And Download.  
Storage  
Consumer Information  
GREAT BRITAIN  
Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB.  
Helpline: 01628 500302.  
Toy Bar  
AUSTRALIA  
Mattel Australia Pty. Ltd., 658 Church Street,  
Locked Bag #870, Richmond, Victoria 3121 Australia.  
Consumer Advisory Service 1300 135 312.  
ASIA  
Mattel East Asia Ltd, Room 1106, South Tower,  
World Finance Centre, Harbour City, Tsimshatsui, HK, China.  
PRESS BUTTON  
MALAYSIA  
Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P)  
Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf  
Country Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867.  
• Push the toy bar backward to its storage position.  
• Press the button on each housing and push the rear legs toward  
the front legs. Stand the frame against a wall for storage.  
Download from Www.Somanuals.co1m5. All Manuals Search And Download.  
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.  
©2004 Mattel, Inc. All Rights Reserved.  
® and ™ designate U.S. trademarks of Mattel, Inc.  
PRINTED IN CHINA  
H4792pr-0726  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Clover Electronics Camcorder Z570 User Manual
Coustic Stereo Amplifier 160SE User Manual
Craftsman Lawn Mower 917377542 User Manual
Curtis Flat Panel Television LCD2622A User Manual
Cypress Computer Hardware CY62157E User Manual
Dynex Network Card DX ESATAP User Manual
Electro Voice Portable Speaker S 152 User Manual
Fellowes Paper Shredder 320 320C 320 2HS 380 380C User Manual
Fender Car Amplifier P N 030780 User Manual
Fisher Paykel Garbage Disposal GD75IA1 User Manual