Extron electronic Stereo Amplifier 68 713 01 User Manual

User Guide  
Distribution Amplifier  
P/2 DA2xi MT  
Two Output VGA and Audio  
Distribution Amplifier  
68-713-01 Rev. G  
01 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC Class A Notice  
This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable  
protection against harmful interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate radio frequency energy and,  
if not installed and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a residential area is  
likely to cause interference; the user must correct the interference at his own expense.  
NOTE: This unit was tested with shielded I/O cables on the peripheral devices. Shielded  
cables must be used to ensure compliance with FCC emissions limits.  
For more information on safety guidelines, regulatory compliances,  
EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and  
Regulatory Compliance Guide” on the Extron website.  
Specifications Availability  
Product specifications are available on the Extron website, www.extron.com.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Conventions Used in this Guide  
Notifications  
The following notifications are used in this guide:  
WARNING: A warning indicates a situation that has the potential to result in death or  
severe injury.  
CAUTION: A caution indicates a situation that may result in minor injury.  
ATTENTION: Attention indicates a situation that may damage or destroy the product or  
associated equipment.  
NOTE: A note draws attention to important information.  
Copyright  
© 2013 Extron Electronics. All rights reserved.  
Trademarks  
All trademarks mentioned in this guide are the properties of their respective owners.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Introduction...................................................1  
Features ............................................................. 1  
Installation.....................................................2  
Connectors, Indicators, and Controls ................. 2  
Mounting............................................................ 5  
UL rack mounting guidelines........................... 5  
Rack mounting ............................................... 6  
Furniture mounting.......................................... 7  
Reference Information .................................8  
Included Parts .................................................... 8  
Other Accessories.............................................. 8  
P/2 DA2xi MT User Guide • Contents  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
The Extron P/2 DA2xi MT is a distribution amplifier that accepts video input from a VGA,  
XGA, UXGA, or QXGA compatible PC and distributes the signal to separately buffered  
outputs. The output on the back of the unit can be extended with Extron VGA Series cables  
from 6 feet to 250 feet in length. The MT model also has audio input and output.  
Features  
Power and Signal LED — Green LED = power + signal. Amber LED = power but no  
signal. Off = no power.  
Gain and Peak DIP switch — Use this feature to compensate for longer cable runs.  
Out Imp DIP switch — Changes the output impedance to be compatible with all  
projectors.  
Cable retention chain — The input cable can be secured to the unit with the supplied  
chain (attached to the right standoff nut of the input VGA connector) to prevent the  
cable from being lost or misplaced.  
INPUT  
MONITOR  
AUDIO  
Figure 1. P/2 DA2xi MT Distribution Amplifier  
P/2 DA2xi MT User Guide • Introduction  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
The Installation section describes:  
Connectors, Indicators, and Controls  
Connectors, Indicators, and Controls  
The front and rear panels of the P/2 DA2xi MT are described below.  
2
3  
4
INPUT  
MONITOR  
1  
5  
AUDIO  
7  
8  
6
GAIN/PEAK  
OUT IMP  
EXT POWER (see manual)  
P/2 DA2xi MT  
OUTPUT L  
12V  
0.2A MAX  
R
9
ON  
1
2
Figure 2. Front and Rear Panels  
a Power and Signal indicator LED — When lit green, this LED indicates that the  
distribution amplifier is receiving both power and a computer signal. When lit amber, it  
indicates that the distribution amplifier is receiving power but no computer signal.  
b Audio input connector — Plug a 3.5 mm, mini plug audio cable from the sound card  
of a computer into this jack.  
c Video input connector — Connect the VGA-QXGA output of a computer to this  
connector.  
d Monitor connector — Connect a local monitor to this connector.  
P/2 DA2xi MT User Guide • Installation  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
e Power connector — Plug the external 12 V power supply, only when needed (see  
“Power and Signal indicator LED” on page 2), into this 2-pole captive screw connector.  
The included power supply is shipped with a plug installed. If you need to cut the DC  
output cord to a different length and reinstall the plug, refer to the following figure and  
notes.  
Smooth  
Ridges  
A
A
SECTION A–A  
Power Supply  
Output Cord  
Tie Wrap  
5
3
Captive Screw  
Connector  
Figure 3. Power Connector Wiring  
ATTENTION: Potential Damage to Property.  
Always use a power supply provided by or specified by Extron. Use of an  
unauthorized power supply voids all regulatory compliance certification and  
may cause damage to the supply and the end product.  
Unless otherwise stated, the AC/DC adapters are not suitable for use in air  
handling spaces or in wall cavities. The power supply is to be located within  
the same vicinity as the Extron AV processing equipment in an ordinary loca-  
tion, Pollution Degree 2, secured to the equipment rack within the dedicated  
closet, podium or desk.  
The installation must always be in accordance with the applicable provisions of  
National Electrical Code ANSI/NFPA 70, article 75 and the Canadian Electrical  
Code part 1, section 16. The power supply shall not be permanently fixed to  
building structure or similar structure.  
When you connect the power supply, voltage polarity is extremely important.  
Applying power with incorrect voltage polarity could damage the power supply  
and the amplifier. Identify the power cord negative lead by the ridges on the  
side of the cord.  
NOTE: Do not tin the stripped power supply leads before installing the captive screw  
connector. Tinned wires are not as secure in the connectors and could pull out. Strip  
the power cord jacket 5 mm from the end.  
CAUTION: Possible Electric Shock.  
The two power cord wires must be kept separate while the power supply is plugged  
in. Remove power before continuing.  
To verify the polarity before connection, plug in the power supply with no load and check the  
output with a voltmeter.  
P/2 DA2xi MT User Guide User Guide • Installation  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
f Two-bank DIP switches — These switches affect only the video output ( ), not the  
g
“monitor” output ( ). The Gain/Peak DIP switch should be on (up) when the output  
d
cable is over 100 feet (30.5 m). The Out Imp DIP switch changes output impedance. If  
all connections and operations are correct, but the output device has no picture, switch  
to the other position.  
g Video output connector — Connect the video output device (projector, display panel,  
or monitor) to this connector.  
h Audio output connector — Wire a 3.5 mm 5-pole captive screw audio connector as  
shown below, and plug it into this connector. Connect the other end of the cable to an  
audio output device or recorder.  
Tip  
Ring  
Sleeve(s)  
Tip  
Tip  
NO GROUND HERE.  
Sleeve(s)  
Tip  
Do not tin the wires!  
Ring  
NO GROUND HERE.  
Unbalanced Stereo Output  
Balanced Stereo Output  
ATTENTION: Potential Damage to Property.  
Connect the sleeve to ground (Gnd). Connecting the sleeve to a negative (-) terminal  
will damage the audio output circuits.  
i Local monitor cable assembly — Use this cable assembly to connect the local  
monitor (video) and speaker (audio) to the unit. The chain is used to attach the cable to  
the unit, to prevent the cable from being lost or misplaced.  
P/2 DA2xi MT User Guide User Guide • Installation  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting  
WARNING: May result in serious injury.  
Installation and service must be performed by authorized personnel only (see  
UL rack mounting guidelines below.  
The P/2 DA2xi MT can be mounted on a rack shelf, under a desk or tabletop, or on a  
projector bracket.  
UL rack mounting guidelines  
The following Underwriters Laboratories (UL) guidelines pertain to the safe installation of the  
equipment in a rack.  
1. Elevated operating ambient temperature — If installed in a closed or multi-unit rack  
assembly, the operating ambient temperature of the rack environment may be greater  
than room ambient temperature. Therefore, install the unit in an environment compatible  
with the maximum ambient temperature (Tma = +122 °F, +50 °C) specified by Extron.  
2. Reduced air flow — Install the equipment in a rack so that the amount of air flow  
required for safe operation of the equipment is not compromised.  
3. Mechanical loading — Mount the equipment in the rack so that a hazardous condition  
is not achieved due to uneven mechanical loading.  
4. Circuit overloading — Connect the equipment to the supply circuit and consider the  
effect that circuit overloading might have on overcurrent protection and supply wiring.  
Appropriate consideration of equipment nameplate ratings should be used when  
addressing this concern.  
5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted  
equipment. Pay particular attention to supply connections other than direct connections  
to the branch circuit (that is, use of power strips).  
P/2 DA2xi MT User Guide User Guide • Installation  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Rack mounting  
For optional rack mounting, mount the P/2 DA2xi MT on a19-inch, 1U RSF 123 rack shelf  
kit (part #60-190-20), a universal RSU 126 1U 6-inch deep rack shelf kit (part #60-190-10),  
or a universal RSU 129 1U 9.5-inch deep rack shelf kit (part #60-190-01), as shown below.  
1. Remove the rubber feet (if installed) and mount the unit on the rack shelf, using two  
screws in opposite (diagonal) corners.  
2. Install blank panels or other units to the rack shelf, as required.  
3. Insert the shelf into the rack, and secure the shelf to the rack using the supplied  
machine screws.  
RSU 123  
Rack Shelf for  
3.5" Deep Products  
RSU 129  
1U Universal Rack Shelf  
1/2 Rack Width  
False Faceplate  
1/4 Rack Width  
False Faceplate  
1/4 Rack Width  
False Faceplate  
Both front false faceplates  
use 2 screws.  
Use 2 mounting holes  
on opposite corners.  
(2) 4-40 x  
3/16" Screws  
Use 2 mounting holes  
on opposite corners.  
(2) 4-40 x 3/16"  
Screws  
Figure 4. Rack Mounting Options  
P/2 DA2xi MT User Guide User Guide • Installation  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Furniture mounting  
For optional furniture mounting, mount the unit using the mounting kit MBU 125  
(part #70-077-01, provided with the P/2 DA2xi MT) as follows:  
1. Attach the mounting brackets to the distribution amplifier with the provided machine  
screws, as shown below.  
INPU  
T
MONI  
T
O
R
Figure 5. Furniture Mounting Option  
2. If feet were previously installed on the bottom of the unit, remove them.  
3. Hold the unit with the attached brackets against the underside of the table or other  
furniture. Mark the location of the screw holes of the bracket on the mounting surface.  
4. Drill 3/32 inch (2 mm) diameter pilot holes, 1/4 inch (6.3 mm) deep in the mounting  
surface at the marked screw locations.  
5. Insert #8 wood screws into the four pilot holes. Tighten each screw into the mounting  
surface until just less than 1/4 inch of the screw head protrudes.  
6. Align the mounting screws with the slots in the brackets and place the unit against the  
surface, with the screws through the bracket slots.  
7. Slide the unit slightly forward or back, then tighten all four screws to secure the unit in  
place.  
P/2 DA2xi MT User Guide • Reference Information  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
Information  
Included Parts  
Included parts  
Replacement  
part number  
60-506-21  
P/2 DA2xi MT  
MBU 125 1U, 1/2 rack width under-desk mount kit  
70-077-01  
VGA-A M-M MD/6 6-foot 15-pin HD male-to-male VGA  
cable with audio  
26-490-02  
P/2 DA2xi MT Setup Guide  
Other Accessories  
Description  
Part number  
RSF 123 1U, 3.5” deep rack shelf kit  
RSU 126 1U, 6” D universal rack shelf kit  
RSU 129 1U, 9.5” deep universal rack shelf  
60-190-20  
60-190-10  
60-190-01  
P/2 DA2xi MT User Guide • Reference Information  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Extron Warranty  
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years  
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty  
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,  
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is  
returned within the warranty period, with proof of purchase and description of malfunction to:  
USA, Canada, South America,  
and Central America:  
Extron Electronics  
1230 South Lewis Street  
Anaheim, CA 92805  
U.S.A.  
Japan:  
Extron Electronics, Japan  
Kyodo Building, 16 Ichibancho  
Chiyoda-ku, Tokyo 102-0082  
Japan  
Europe and Africa:  
Extron Europe  
Hanzeboulevard 10  
3825 PH Amersfoort  
The Netherlands  
China:  
Extron China  
686 Ronghua Road  
Songjiang District  
Shanghai 201611  
China  
Asia:  
Middle East:  
Extron Asia  
Extron Middle East  
135 Joo Seng Road, #04-01  
PM Industrial Bldg.  
Singapore 368363  
Singapore  
Dubai Airport Free Zone  
F12, PO Box 293666  
United Arab Emirates, Dubai  
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical  
or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not  
authorized by Extron.  
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return  
Authorization) number. This will begin the repair process.  
USA:  
Asia:  
714.491.1500 or 800.633.9876  
65.6383.4400  
Europe: 31.33.453.4040  
Japan: 81.3.3511.7655  
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage  
during shipment. Returned units must include the serial number and a description of the problem, as well as the  
name of the person to contact in case there are any questions.  
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,  
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,  
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been  
advised of such damage.  
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may  
not apply to you.  
Extron Headquarters  
Extron Europe  
Extron Asia  
Extron Japan  
Extron China  
Extron Middle East  
Extron Korea  
Extron India  
+1.800.633.9876 (Inside USA/Canada Only)  
+800.3987.6673  
(Inside Europe Only)  
800.3987.6673  
(Inside Asia Only)  
+65.6383.4400  
+81.3.3511.7655  
+81.3.3511.7656 FAX  
+4000. 398766  
(Inside China Only)  
+971.4.299.1800  
+971.4.299.1880 FAX  
+82.2.3444.1571  
+82.2.3444.1575 FAX  
1800.3070.3777  
(Inside India Only)  
Extron USA - West  
+1.714.491.1500  
Extron USA - East  
+1.919.850.1000  
+31.33.453.4040  
+31.33.453.4050 FAX  
+86.21.3760.1568  
+86.21.3760.1566 FAX  
+91.80.3055.3777  
+91.80.3055.3737 FAX  
+65.6383.4664 FAX  
+1.714.491.1517 FAX  
+1.919.850.1001 FAX  
© 2013 Extron Electronics All rights reserved. www.extron.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Cornelius Beverage Dispenser Tea Tower User Manual
Crane Humidifier EE 5063 User Manual
Curtis DVD Player DVD1043 User Manual
Dell Server E11S User Manual
Dimplex Indoor Fireplace COMPACT FIREPLACE User Manual
Electro Voice Speaker System FRi 2082 User Manual
Event electronic Portable Speaker Biamplified Direct Field Monitor System User Manual
Frigidaire Dehumidifier 66129900901 User Manual
GE Air Conditioner AZ41E09EAC User Manual
Global Machinery Company Portable Generator LSSLV User Manual