9.5 AMP MAGNESIUM
RECIPROCATING SAW
97580
SET UP AND OPERATING INSTRUCTIONS
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor
FreightTools. Diagramswithinthismanualmaynotbedrawnproportionally. Duetocontinuingimprovements,
actual product may differ slightly from the product described herein.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 10b
Download from Www.Somanuals.com. All Manuals Search And Download.
Distractions can cause you to lose
control.
not use a power tool while you
are tired or under the influence of
drugs, alcohol or medication. A
moment of inattention while operating
power tools may result in serious
personal injury.
2. Electrical safety
a.Power tool plugs must match the
outlet. Never modify the plug in
any way. Do not use any adapter
plugs with grounded power tools.
Unmodified plugs and matching
outlets will reduce risk of electric
shock.
b.Use safety equipment. Always
wear ANSI-approved eye
protection. Safety equipment such
as dust mask, non-skid safety shoes,
hard hat, or hearing protection used
for appropriate conditions will reduce
personal injuries.
b.Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is
an increased risk of electric shock if
your body is grounded.
c.Prevent unintentional starting.
Ensure the switch is in the off-
position before connecting to
power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your finger
on the switch or energizing power
tools that have the switch on invites
accidents.
c.Do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
d.Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged
or entangled cords increase the risk
of electric shock.
d.Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
e.When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces
the risk of electric shock.
e.Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
f. If operating a power tool in a damp
location is unavoidable, use a
Ground Fault Circuit Interrupter
(GFCI) protected supply. Use of
a GFCI reduces the risk of electric
shock.
f. Dress properly. Do not wear loose
clothing or jewelry. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,
jewelry or long hair can be caught in
moving parts.
g.If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
3. Personal safety
a.Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Use of these devices can reduce
dust-related hazards.
g.Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed.
Use of the power tool for operations
different from those intended could
result in a hazardous situation.
4. Power tool use and care
a.Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
5. Service
b.Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
a.Have your power tool serviced by
a qualified repair person using
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
c.Disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, changing
accessories, or storing power
tools. Such preventive safety
measures reduce the risk of starting
the power tool accidentally.
Reciprocating Saw Safety
Warnings
1. Hold power tool by insulated
gripping surfaces when performing
an operation where cutting tool
may contact hidden wiring or its
own cord. Contact with a ″ live″ wire
will make exposed metal parts of the
tool ″ live″ and shock the operator.
d.Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power
tools are dangerous in the hands of
untrained users.
2. Use clamps or another practical
way to secure and support the
work piece to a stable platform.
Holding the work by hand or against
your body leaves it unstable and may
lead to loss of control.
e.Maintain power tools. Check
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tool’s operation.
If damaged, have the power
tool repaired before use. Many
accidents are caused by poorly
maintained power tools.
3. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
4. Avoid unintentional starting. Prepare
to begin work before turning on the
tool.
f. Keep cutting tools sharp and
clean. Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier to
control.
5. Do not lay the tool down until it has
come to a complete stop. Moving
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
parts can grab the surface and pull
the tool out of your control.
Your risk from these exposures
varies, depending on how often you
do this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to filter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
6. When using a handheld power tool,
maintain a firm grip on the tool with
both hands to resist starting torque.
7. Do not leave the tool unattended
when it is plugged into an electrical
outlet. Turn off the tool, and unplug
it from its electrical outlet before
leaving.
11. WARNING: Handling the cord on
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and
birth defects or other reproductive
harm. Wash hands after handling.
(California Health & Safety Code §
25249.5, et seq.)
8. This product is not a toy. Keep it out
of reach of children.
9. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference or
pacemaker failure. In addition,
people with pacemakers should:
• Avoid operating alone.
12. The warnings, precautions,
and instructions discussed in
this instruction manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
• Do not use with power switch locked
on.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also be
implemented – it prevents sustained
electrical shock.
Vibration Safety
This tool vibrates during use.
Repeated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly
to the hands, arms and shoulders. To
reduce the risk of vibration-related
injury:
10. Some dust created by power
sanding, sawing, grinding, drilling,
and other construction activities,
contains chemicals known [to the
State of California] to cause cancer,
birth defects or other reproductive
harm. Some examples of these
chemicals are:
1. Anyone using vibrating tools regularly
or for an extended period should
first be examined by a doctor and
then have regular medical check-
ups to ensure medical problems are
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from
chemically treated lumber
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries,
nervous system disorders, diabetes,
or Raynaud’s Disease should not
use this tool. If you feel any medical
or physical symptoms related to
vibration (such as tingling, numbness,
and white or blue fingers), seek
medical advice as soon as possible.
GROUNDING
TO PREVENT
ELECTRIC SHOCK
AND DEATH FROM
INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualified
electrician if you are in doubt
as to whether the outlet is
properly grounded. Do not
modify the power cord plug
provided with the tool. Never
remove the grounding prong
from the plug. Do not use the
tool if the power cord or plug
is damaged. If damaged, have
it repaired by a service facility
before use. If the plug will not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
2. Do not smoke during use. Nicotine
reduces the blood supply to the
hands and fingers, increasing the risk
of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice between
different processes.
5. Include vibration-free periods each
day of work.
NOTE: THIS IS A DOUBLE
INSULATED TOOL.
INFORMATION ON
GROUNDED TOOLS IS FOR
REFERENCE ONLY.
6. Grip tool as lightly as possible (while
still keeping safe control of it). Let
the tool do the work.
7. To reduce vibration, maintain the tool
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
Grounded Tools: Tools with Three
Prong Plugs
SAVE THESE
INSTRUCTIONS.
1. Tools marked with “Grounding
Required” have a three wire cord
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
requirements and complies with the
applicable standards of Underwriters
Laboratories, Inc., the Canadian
Standard Association, and the
National Electrical Code. (See
Outlets for 2-Prong Plug.)
and three prong grounding plug.
The plug must be connected to a
properly grounded outlet. If the tool
should electrically malfunction or
break down, grounding provides a
low resistance path to carry electricity
away from the user, reducing the risk
of electric shock. (See 3-Prong Plug
and Outlet.)
2. Double insulated tools may be used
in either of the 120 volt outlets shown
in the preceding illustration. (See
Outlets for 2-Prong Plug.)
2. The grounding prong in the plug is
connected through the green wire
inside the cord to the grounding
system in the tool. The green wire
in the cord must be the only wire
connected to the tool’s grounding
system and must never be attached
to an electrically “live” terminal. (See
3-Prong Plug and Outlet.)
Extension Cords
1. Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
2. As the distance from the supply
outlet increases, you must use a
heavier gauge extension cord. Using
extension cords with inadequately
sized wire causes a serious drop in
voltage, resulting in loss of power and
possible tool damage.
3. The tool must be plugged into an
appropriate outlet, properly installed
and grounded in accordance with all
codes and ordinances. The plug and
outlet should look like those in the
preceding illustration. (See 3-Prong
Plug and Outlet.)
(See Table A.) The smaller the
gauge number of the wire, the
greater the capacity of the cord. For
example, a 14 gauge cord can carry
a higher current than a 16 gauge
cord. (See Table A.)
Double Insulated Tools: Tools
with Two Prong Plugs
3. When using more than one extension
cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(See Table A.)
4. If you are using one extension cord
for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size. (See Table A.)
1. Tools marked “Double Insulated”
do not require grounding. They
have a special double insulation
system which satisfies OSHA
5. If you are using an extension cord
outdoors, make sure it is marked with
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
the suffix “W-A” (“W” in Canada) to
indicate it is OK for outdoor use.
6. Make sure the extension cord is
properly wired and in good electrical
condition. Always replace a damaged
extension cord or have it repaired by
a qualified electrician before using it.
7. Protect the extension cords from
sharp objects, excessive heat, and
damp or wet areas.
RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS*
(120/240 VOLT)
EXTENSION CORD
NAMEPLATE
LENGTH
AMPERES
(at full load)
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* Based on limiting the line
voltage drop to five volts at
150% of the rated amperes.
TABLE A
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
V~
A
No Load Revolutions per Minute
(RPM)
n xxxx/min.
0
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
INSTRUCTIONS FOR
PUTTING INTO USE
Electrical
Requirements
120 V~ / 60 Hz/9.5 A
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set up
or use of this product.
Motor No Load Speed 0-2500 RPM
Maximum Cut Depth 6 inches
Length of Stroke
1-1/8 inch
Twist Ring Quick
Release Chuck for 1/2”
Shank Blades
Blade Fastening
System
TO PREVENT
SERIOUS INJURY
Required Blade Type 1/2” Shank
Metal Cutting : 4-1/8”
FROM ACCIDENTAL
OPERATION:
x 5/8” x 20ga. 25 TPI
Wood Cutting: 5-11/16”
x 3/4” x 18 ga. 11TPI
Included Blades
Turn the Power Switch of the tool
to its “OFF” position and unplug
the tool from its electrical outlet
before assembling or making
any adjustments to the tool.
Base Plate
Dimensions
3-1/2” L x 1-5/8” W
15 ga. Aluminum
Shoe Plate Tilt Range 80° x 110°
(2) Fully Shielded
Radial Bearings
Armature Bearings
Power Control
Note: For additional information regarding the
parts listed in the following pages, refer
to the Assembly Diagram near the end of
this manual.
Trigger Switch with
Lock-On Button
Assembly: Installing the Blade
E194601
1. Be sure the tool is unplugged from its
power source. Wear heavy duty work
gloves.
UNPACKING
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
Shoe Plate (44)
Chuck (8)
List of contents
Part #
Description
Reciprocating Saw
Wood Cutting Blade
Metal Cutting Blade
Allen Key
Qty
1
1
1
1
1
43
43
67
Owner’s Manual
Set Screws (38)
REV 10b
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Select a Blade that is appropriate
for the task at hand. See the Blade
Selection Chart on page 14 for sug-
gested blade size and type.
2. Retracted blade length should be
wider than workpiece. If the Blade
is shorter, it’s tip will jam in the work
piece during cutting, possibly causing
injury and damaging the Blade or
work piece.
3. Rotate the Chuck (8)
counterclockwise to open it. Hold
it in the open position. (See Photo
previous page.)
3. The Base Plate (44) can be
adjusted to limit the amount of Blade
protrusion. Loosen Set Screws (38)
located on the underside of the
Front Cover (42). (See photo.) Slide
the Base Plate (44) straight in or
out of the Front Cover as required.
Retighten the Set Screws.
4. Insert the 1/2” shank of the selected
Blade (43) firmly into the Chuck. Be
sure the Blade is fully inserted.
5. Release the Chuck to close it.
6. With work gloves on, pull on the
Blade to ensure that it is firmly
installed. Operating this tool with a
loose blade can cause injury.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Using the Allen Key (67) to loosen the Set
Screws (38) to adjust the Base Plate (44).
Work Piece and Work Area Set Up
1. Designate a work area that is clean
and well-lit. The work area must not
allow access by children or pets to
prevent injury and distraction.
Tool Set Up
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
2. Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage.
The power cord must reach the work
area with enough extra length to
Turn the Power Switch of the
tool to its “OFF” position and
unplug the tool from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
allow free movement while working.
3. Secure loose work pieces using
a vise or clamps (not included) to
prevent movement while working.
1. Only install a Blade that is in good
condition, and is appropriate to the
work you will be doing.
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
4. There must not be hazardous
objects, such as utility lines or foreign
objects, nearby that will present a
hazard while working.
another cut unplug the tool and store
it safely.
Plunge Cutting
1. You can plunge cut into plywood and
thin board panels. Do not attempt to
plunge cut into thick, hard or metal
panels.
General Operating Instructions
1. To turn ON the tool, squeeze the
Trigger (60). To turn the tool OFF,
release the Trigger.
2. Select a short, thick blade which is in
good condition.
2. The tool can be set to operate
continuously, by squeezing the
Trigger and pressing in the Locking
Button on the Handle. To stop
continuous operation, squeeze the
Trigger to unlock the Button and
release the Trigger.
3. Place the tool on the work piece with
the Blade NOT touching the work
material. Squeeze the Trigger (60)
to start the tool operating. Never
start a plunge cut with the Blade tip
touching the work piece. This will
cause an immediate kick back, that
can damage the work piece, blade or
cause injury.
3. Be sure the work piece is firmly
mounted so it will not move during
the cutting operation. Support the cut
off end of the work piece so it will not
fall free at the end of the cut.
4. Slowly rotate the tool on the Base
Plate (44) as the Blade contacts the
work piece. Hold the tool firmly.
4. Grip the tool with both hands, one
hand on the Handle (58,65), and one
on the Front Cover (42).
5. Continue to slowly rotate the tool until
the Blade has penetrated through the
work material. Press the Base Plate
(44) firmly against the work material
and continue to make the cut.
5. Place the Blade (43) on the work
piece and squeeze the Trigger (60).
The saw will begin to operate.
6. Keep the Base Plate (44) pressed
firmly against the work piece to
prevent tool kick back.
6. To prevent accidents, turn off the tool
and disconnect its power supply after
use. Clean, then store the tool in-
doors out of children’s reach.
7. Maintain a smooth motion pressing
the Blade through the material as it
is cut. Follow the cut, do not press
too hard. If the tool slows down as it
is cutting, apply less pressure on the
tool.
8. When the cut is completed, release
the Trigger and wait until the blade
stops. If you will not be making
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
damage or injury. Discard damaged
or worn blades.
MAINTENANCE AND
SERVICING
4.
WARNING! If the supply cord of
this power tool is damaged, it must
be replaced only by a qualified
service technician.
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
Replacing Carbon Brushes
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch of the
tool to its “OFF” position and
unplug the tool from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
1. To inspect or replace the Carbon
Brushes, remove the Brush Caps
(54) located on the top and underside
of the Main Housing (53).
2. With the Caps removed, the Brush
Holders (55) and Carbon Brushes
(56) may fall out.
3. Inspect the Carbon Brushes. They
should not be chipped or cracked,
and the carbon portion must be at
least 1/4 in length.
TO PREVENT SERIOUS
INJURY FROM TOOL
FAILURE:
Do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
One of the Carbon Brush Caps (54)
Cleaning, Maintenance, and
Lubrication
1. BEFORE EACH USE, inspect the
general condition of the tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical
wiring, and any other condition that
may affect its safe operation.
4. If the Carbon Brushes are worn or
damaged, they must be replaced.
Replacement Carbon Brushes are
available from Harbor Freight Tools.
2. AFTER USE, clean external surfaces
of the tool with clean cloth.
3. Check the condition of Blades. Bent,
cracked, worn or dull blades will
not operate properly and can cause
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Possible Causes
Likely Solutions
Tool will not start
1. No power at outlet.
2. Cord not connected.
3. Carbon Brushes may be worn 3. Inspect Carbon Brushes and replace if
or damaged. necessary.
1. Carbon Brushes may be worn 1. Inspect Carbon Brushes and replace if
or damaged. necessary.
1. Check power at outlet.
2. Check that cord is plugged in.
Tool operates
slowly or
sporadically.
Tool does not
cut effectively or
blade jams in work
material
1. Blade may be damaged, worn 1. Check condition and type of blade. Use only
or wrong type for the material.
proper type of blade in good condition.
2. Too much pressure.
2. Ease off pressure on blade.
Follow all safety precautions whenever diagnosing or servicing the
tool. Disconnect power supply before service.
Blade Selection Chart
Work Material Type Blade Length TPI
Blade Material
Wood
6 - 12 inches
5 - 11
Carbon Steel
Wood with embed- 6 - 12 inches
11
Carbide tipped Steel (“bi-metal”)
ded nails or screws
Metal
6 - 9 inches
10 - 25
9 - 25
Carbide tipped Steel (“bi-metal”)
or Carbide Grit
Plastic
6 - 12 inches
Carbon Steel or Carbide Grit
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIEDAND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
PARTS LIST
Part
Description
Phillips Pan Head Screw
Spring Washer m5
Gear Cover
Phillips Head Pan Screw
Spring Washer m5
Cover Plate
Retainer Ring
Chuck (outer Ring)
Torsion Spring
Qty.
4
2
1
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
3
3
1
1
1
1
1
1
1
1
Part
Description
Qty.
2
4
2
1
1
2
1
1
1
1
1
1
2
2
1
1
2
2
2
1
1
7
1
2
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
38 Set Screw
39 Spring Washer m5
40 Flat Washer m5
41 Bumper
42 Front Cover
43 Saw Blade
44 Shoe Plate
45 Rotor
46 Baffle Ring
47 Bearing 608
48 Bearing Sleeve
49 Magnesium Gear Cover
50 Phillips Pan Head Screw
51 Flat Washer m4
52 Stator
10 Inner Ring
11 Compression Spring
12 Pin
13 Spring Pin
14 Wool Gasket Ring
15 Gasket Ring Cap
16 Plastic Ring
17 Sealed Bearing
18 Reciprocating Lever
19 Middle Plate
20 Spindle
21 Needle Bearing
22 Cylinder Pin
23 Baffle Ring m7
24 Gear
53 Main Housing
54 Brush Cap
55 Brush Holder
56 Carbon Brush
57 Name Plate (left)
58 Handle (right section)
59 Phillips Pan Head Screw
60 Trigger Switch
61 Phillips Pan Head Screw
62 Cable Clamp
63 Cable Sleeve
64 Power Cable
65 Handle (left section)
66 Label
25 Flat Washer
26 Phillips Head Pan Screw
27 Bearing
28 Phillips Head Screw
29 Lock Washer
30 Bearing Plate
31 Bearing 6201
32 Circlip for Shaft
33 Gear Housing
34 Bearing 6000
35 Flat Washer
67 Allen Key
Included Blades
Wood Cutting Blade: 11 TPI, 5-3/4” Long
Metal Cutting Blade: 25 TPI, 3-1/4” Long
36 Phillips Head Screw
37 Seal Cover
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free
from defects in materials and workmanship for the period of 90 days from the date of
purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal
activity, improper installation, normal wear and tear, or to lack of maintenance. We
shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 97580
For technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
|