MA1206-EA
Ú ꢀꢁꢂꢀ #!3)/ #/-054%2 #/ꢃꢄ ,4$ꢃ
Operation Guide ANA(6HST-B)
• Your watch may differ somewhat from the one shown in the illustration.
Specifications
5139 5150/5169
Accuracy at normal temperature: 20 seconds a month
Stopwatch function: Measuring capacity: 29'59"
Measuring unit: 1 second
Stopwatch minute hand
Stopwatch minute hand
Hour hand
Minute hand
24-hour hand
Hour hand
Measuring mode: Elapsed time
24-hour hand
Minute hand
Battery: One silver oxide battery (Type: SR621SW)
Approximately 2 years on type SR621SW (assuming one stopwatch operation 30 min./
day)
First click
(setting day)
First click
(setting day)
Second click
(setting time)
Second click
(setting time)
Second hand
Day
Second hand
Day
Crown
(normal position)
Crown
(normal position)
Stopwatch second hand
Stopwatch second hand
5162
Stopwatch minute hand
Hour hand
5305
Stopwatch minute hand
Hour hand
24-hour hand
24-hour hand
Minute hand
Minute hand
First click
(setting day)
First click
(setting day)
ꢃꢅ
ꢂꢃ
ꢀꢁ
ꢀꢁ
ꢃꢁ
ꢂꢁ
ꢄꢁ
ꢀꢁ
Second click
(setting time)
Second click
(setting time)
Second hand
Day
Second hand
Day
Crown
(normal position)
Crown
(normal position)
Stopwatch second hand
Stopwatch second hand
To set the time
1. Pull out the crown to the second click.
• This causes the second hand to stop.
2. Set the hands by rotating the crown.
Move the minute hand four or five minutes past the time you want to set, and
then back it up to the proper setting.
3. Push the crown back in to the normal position to restart timekeeping.
To set the day
1. Pull out the crown to the first click.
2. Set the day by rotating the crown.
3. Push the crown back in to the normal position.
• Avoid setting the day between 9:00 p.m. and 1:00 a.m. (the day display may not
change in the following day).
Using the Stopwatch
The stopwatch lets you measure elapsed time up to 29 minutes, 59 seconds.
To measure times with the stopwatch
Elapsed time
A
A
A
A
B
Start
Stop
Re-start
Stop
Clear
To adjust the positions of the stopwatch minute hand and stopwatch
second hand
• This procedure should be performed when the stopwatch minute hand and
stopwatch second hand do not return to the zero positions.
1. Press B to reset the stopwatch.
2. Pull out the crown to the second click.
3. Press A to move the stopwatch second hand forward until it points to the
zero position.
• The stopwatch minute hand is synchronized with the stopwatch second hand.
4. Push the crown back in to its normal position.
• Note that pulling the crown out also stops the timekeeping second hand. After
performing the above procedure, you should also adjust the timekeeping setting.
■ For a watch with an elapsed time bezel
Rotate the elapsed time bezel to align the
minute hand.
mark with the
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
Elapsed time bezel
• Some water resistant models are equipped with a screw
lock crown.
• With such models, you must unscrew the crown in the
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
• Also note that such watches are not water resistant while
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
|