Model No. WLTL39810.0
Serial No.
USER'S MANUAL
Write the serial number in the space
above for reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, please con-
tact the store where you pur-
chased this product.
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with
pre-existing health problems.
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 9. To purchase a surge suppressor, see
your local WESLO dealer or see your local
electronics store.
3. Use the treadmill only as described.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
5. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 16 if the treadmill is
not working properly.)
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 11).
8. The treadmill should not be used by persons
weighing more than 250 lbs. (113 kg).
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes 18. The pulse sensor is not a medical device.
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes; never use the treadmill with bare feet,
wearing only stockings, or in sandals.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The pulse sensor is intended only as an exer-
cise aid in determining heart rate trends in
general.
11. When connecting the power cord (see page 9),
plug the power cord into a surge suppressor
3
Download from Www.Somanuals.com. All Manuals Search And Download.
19. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
24. Inspect and properly tighten all parts of the
treadmill regularly.
25. Never drop or insert any object into any
opening on the treadmill.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and press the power switch
into the off position when the treadmill is not
in use. (See the drawing on page 5 for the lo-
cation of the power switch.)
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
27.
DANGER:
Always unplug the power
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6 and HOW TO FOLD
AND MOVE THE TREADMILL on page 15.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
28. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
23. Do not change the incline of the treadmill by
placing objects under the treadmill.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
®
Thank you for selecting the new WESLO CADENCE
ing this manual, please see the front cover of this man-
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
G 7.0 treadmill. The CADENCE G 7.0 treadmill offers a
selection of features designed to make your workouts
at home more effective. And when youʼre not exercis-
ing, the unique treadmill can be folded up, requiring
less than half the floor space of other treadmills.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Length: 5 ft. 5 in. (165 cm)
Accessory
Width: 2 ft. 4 in. (74 cm)
Tray
Console
Key/Clip
Handrail
Storage Latch
Motor Hood
Power Switch
Walking Belt
Foot Rail
Power Cord
Wheel
Platform Cushion
Idler Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of
the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubricant on top of
the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver
screwdriver , and needlenose pliers
, standard
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: Some small parts may have been preassembled. To avoid dam-
aging parts, do not use power tools for assembly. Extra hardware may be included.
4.2 x 19mm
Screw (3)–6
#10 x 1" Tek
Screw (83)–2
M10 x 45mm Screw (2)–4
M10 x 65mm Patch Screw (1)–4
1. Make sure that the power cord is unplugged.
1
With the help of a second person, carefully tip
the treadmill onto its left side. Unfold the Frame
(50) away from the Uprights (73). Do not lean on
the Uprights.
80
73
50
Orient the Base (80) as shown. Attach the Base
to the Uprights (73) with four M10 x 65mm
Patch Screws (1). Start all four Screws, and
then tighten each of them.
1
Raise the Uprights (73) so that the Base (80) is
flat on the floor.
1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Attach the Handrails (69) to the Uprights (73)
with four M10 x 45mm Screws (2). Start all four
Screws, and then tighten each of them.
2
2
69
69
2
73
3. With the help of a second person, hold the con-
sole assembly near the Uprights (73). Remove
the tie from the Upright Wire (71).
3
Console Assembly
Connect the Upright Wire (71) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. IF YOU DO NOT CONNECT THE CON-
NECTORS PROPERLY, THE CONSOLE MAY
BECOME DAMAGED WHEN YOU TURN ON
THE POWER. Insert the connectors and the ex-
cess wire into the crossbar on the Uprights (73).
Console Wire
73
71
Tie
Console
Wire
71
4. Attach the console assembly to the Uprights
(73) and the Handrails (69) with six M4.2 x
19mm Screws (3). Be careful not to pinch the
wires.
4
Console Assembly
73
3
3
69
69
3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Attach the Latch Housing (72) to the left Upright
(73) with two #10 x 1" Tek Screws (83); start
both Screws, and then tighten each of them.
5
73
Place the treadmill in the storage position (see
HOW TO FOLD THE TREADMILL on page 15).
72
83
6. Identify the rod end of the Gas Spring (85). See
the two small inset drawings. Locate the
Spring Clip (86) in the rod end of the Gas
6
50
86
Spring. Using your fingernail or a screwdriver,
press on the end of the Spring Clip to loosen it.
Rotate the Spring Clip, and then pull the Spring
Clip out of the Gas Spring. Avoid losing the
Spring Clip. Extra Spring Clips are included.
Bracket
86
86
Rod
85
Next, press the rod end of the Gas Spring (85)
as far as possible onto the Mount (82) on the
bracket in the center of the Frame (50).
See drawing 6a. Insert the Spring Clip (86) into
the two indicated small holes in the rod end of
the Gas Spring (85). Then, rotate the Spring Clip
until it clips onto the Gas Spring.
6a
50
Holes
82
86
85
7. Remove the Spring Clip (86) from the lower end
of the Gas Spring (85). Press the lower end of
the Gas Spring onto the Mount (82) on the
bracket in the center of the Base (80). Note: It
may be necessary to pivot the Frame (not
shown) forward or backward slightly (see HOW
TO LOWER THE TREADMILL FOR USE on
page 15).
7
85
See the inset drawing. Insert the Spring Clip
(86) into the two indicated small holes in the Gas
Spring (85). Rotate the Spring Clip until it clips
onto the Gas Spring.
85
86
86
Bracket
Holes
Bracket
Lower the treadmill. See HOW TO LOWER THE
TREADMILL FOR USE on page 15.
80
80
82
8. Make sure that all parts are properly tightened before you use the treadmill. Keep the included hex keys
in a secure place. One of the hex keys is used to adjust the walking belt (see pages 17 and 18). To protect
the floor or carpet, place a mat under the treadmill.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
dance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets and may not be compatible
with AFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
cause excessive wear.
This product is for use on a nominal 120-volt circuit
(see drawing 1). A temporary adapter may be used to
connect the surge suppressor to a 2-pole receptacle if
a properly grounded outlet is not available (see draw-
ing 2).
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
1
Grounded Outlet Box
of the equipment-grounding conductor in-
creases the risk of electric shock. Check with
a qualified electrician or serviceman if you
are unsure whether the product is properly
grounded. Do not modify the plug—if it will
not fit the outlet, have a proper outlet in-
stalled by a qualified electrician.
Surge Suppressor
Grounding Pin
Grounding Pin
Grounded Outlet
Grounding Plug
Your treadmill, like other electronic equipment, can be
damaged by sudden voltage changes in your homeʼs
power. To decrease the risk of damaging your
treadmill, always use a surge suppressor with your
treadmill (see drawing 1 at the right). To purchase
a surge suppressor, see precaution 12 on page 3.
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL-suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could dam-
age the control system of the treadmill (see precau-
tion 13 on page 3).
Lug
Metal Screw
Grounding Plug
The temporary adapter should be used only until a
properly grounded outlet (see drawing 1) can be in-
stalled by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
The adapter must be held in place by a metal screw.
Some 2-pole receptacle outlet box covers are not
grounded. Contact a qualified electrician to deter-
mine if the outlet box cover is grounded before
using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This productʼs power cord has an equip-
ment-grounding conductor and a grounding plug. Plug
the power cord into a surge suppressor, and plug
the surge suppressor into an appropriate outlet
that is properly installed and grounded in accor-
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Pulse Sensor
Key
Clip
FEATURES OF THE CONSOLE
IMPORTANT: If there is a sheet of plastic on the
face of the console, remove the plastic. To prevent
damage to the walking platform, wear clean ath-
letic shoes while using the treadmill. The first time
the treadmill is used, observe the alignment of the
walking belt, and center the walking belt if neces-
sary (see page 18).
The treadmill console offers a selection of features de-
signed to make your workouts more effective. When
you select the manual mode of the console, you can
change the speed and incline of the treadmill with the
touch of a button. As you exercise, the displays will
provide continuous exercise feedback. You can even
measure your heart rate using the built-in pulse
sensor.
Note: The console can display speed and distance in
either kilometers or miles. To find which unit of mea-
surement is selected, see THE INFORMATION MODE
on page 14. For simplicity, all instructions in this
manual refer to kilometers.
The console also offers eight preset workouts. Each
workout automatically controls the speed and incline of
the treadmill as it guides you through an effective exer-
cise session.
To turn on the power, see page 11. To use the man-
ual mode, see page 11. To use a preset workout,
see page 13. To use the information mode, see
page 14.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord (see
page 9). Next, locate the
power switch on the tread-
mill frame near the power
When the key is in-
serted, the manual
mode will be selected. If
you have selected a pre-
set workout, remove the
key and then reinsert it.
Reset
cord. Make sure that the
switch is in the reset
position.
3. Start the walking belt.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and press the power
switch into the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
14 to turn off the demo mode.
To start the walking belt, press the Start button, the
Speed increase button, or one of the numbered
speed buttons.
If you press the Start button or the Speed increase
button, the walking belt will begin to move at 2
Km/H. As you exercise, change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time you press
one of the buttons, the speed setting will change
by 0.1 Km/H; if you hold down the button, the
speed setting will change in increments of 0.5
Km/H. Note: After you press the buttons, it may
take a moment for the walking belt to reach the se-
lected speed setting.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 10),
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency,
the key can be pulled from the console, causing
the walking belt to slow to a stop. Test the clip by
carefully taking a few steps backward; if the key is
not pulled from the console, adjust the position of
the clip.
If you press one of the numbered speed buttons,
the walking belt will gradually change speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button.
The time will begin to flash in the left display. To
restart the walking belt, press the Start button or
the Speed increase button.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Change the incline of the treadmill as desired.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
To change the incline of the treadmill, press the
Incline increase and decrease buttons. Each time
you press a button, the incline setting will change
by 0.5 percent; if you hold down a button, the in-
cline setting will change quickly.
6. Measure your heart rate if desired.
To measure your heart rate, stand on the foot
rails and place your thumb on the pulse sensor
(see the drawing on page 10). Do not press too
hard, or the circulation in your thumb will be re-
stricted and your pulse may not be detected.
When your pulse is detected, the small heart sym-
bol in the left display will flash and your heart rate
will be shown. For the most accurate heart rate
reading, hold your thumb on the pulse sensor
for at least 15 seconds.
5. Follow your progress with the displays.
The track—The track
represents a distance of
1/4 mile (400 meters).
As you walk or run on
the treadmill, the indica-
tors around the track
will appear in succession until the entire track ap-
pears. The track will then disappear and the indica-
tors will again begin to appear in succession.
If the displayed heart rate appears to be too high or
too low, or if your heart rate is not displayed, lift
your thumb for a few seconds, and then reposition
your thumb on the pulse sensor. Remember to
stand still while measuring your heart rate.
The left display—As
you exercise, this dis-
play can show the
7. When you are finished exercising, remove the
key from the console.
elapsed time and the
approximate number of
calories that you have
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest set-
ting or you may damage the treadmill when you
fold it to the storage position. Next, remove the
key from the console and put it in a secure place.
burned. The left display will also show the incline of
the treadmill each time the incline level changes.
The display also shows your heart rate when you
use the pulse sensor (see step 6 on this page).
Note: When you use a preset workout, the left dis-
play will show the time remaining in the workout in-
stead of the elapsed time.
When you are finished using the treadmill, press
the power switch into the off position and unplug
the power cord. IMPORTANT: If you do not do
this, the treadmillʼs electrical components may
wear prematurely.
The right display—
This display can show
the speed of the walk-
ing belt and the dis-
tance that you have
walked or run.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE A PRESET WORKOUT
1. Insert the key into the console.
At the end of each segment, a series of tones will
sound and the next segment of the profile will
begin to flash. If a new speed and/or incline setting
is programmed for the next segment, the speed
and/or incline will appear in the display and the
treadmill will automatically adjust to the new speed
and incline settings.
See HOW TO TURN ON THE POWER on page 11.
2. Select one of the six preset workouts.
To select a preset workout, press the Weight Loss
Workouts button or the Intensity Training Workouts
button repeatedly until the number of the desired
workout appears in the display. The maximum
speed setting of the selected workout will flash in
the right display for a few seconds and then the du-
ration of the workout will appear. In addition, a pro-
file of the speed settings of the workout will scroll
across the display.
The workout will continue in this way until the last
segment of the profile flashes in the display and
the last segment ends. The walking belt will then
slow to a stop.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the Speed or
Incline buttons; however, when the next segment
of the workout begins, the treadmill will auto-
matically adjust to the speed and incline set-
tings for the next segment.
3. Start the walking belt.
Press the Start button or the Speed increase but-
ton to start the workout. A moment after you press
the button, the treadmill will automatically adjust to
the first speed and incline settings of the workout.
Hold the handrails and begin walking.
To stop the workout at any time, press the Stop
button. To resume the workout, press the Start but-
ton or the Speed increase button. The walking belt
will begin to move at 2 Km/H. When the next seg-
ment of the workout begins, the treadmill will auto-
matically adjust to the speed setting for that
segment.
Each preset workout is divided into segments. One
speed setting and one incline setting are pro-
grammed for each segment. Note: The same
speed and/or incline setting may be programmed
for consecutive segments.
4. Follow your progress with the displays.
See step 5 on page 12.
During the workout, the
profile will show your
progress. The flashing
segment of the profile
represents the current
5. Measure your heart rate if desired.
See step 6 on page 12.
Current Segment
segment of the workout.
The height of the flash-
ing segment indicates
6. When you are finished exercising, remove the
key from the console.
the speed setting for the current segment.
See step 7 on page 12.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE
into the console. However, when you remove the key,
the displays will remain lit, although the buttons will not
function. If the demo mode is turned on, a “d” will ap-
pear in the left display while the information mode is
selected. To turn on or turn off the demo mode, press
the Speed decrease button.
The console features an information mode that allows
you to turn on and turn off the demo mode and to se-
lect miles or kilometers as the unit of measurement.
The information mode also keeps track of treadmill
usage information.
The left display will also show an “M” for metric kilome-
ters or an “E” for English miles. To change the unit of
measurement, press the Speed increase button.
To select the information mode, hold down the Stop
button, insert the key into the console, and then re-
lease the Stop button. When the information mode is
selected, the following information will appear in the
display:
The right display will show
the total number of hours
that the treadmill has been
operated and the total num-
ber of miles or kilometers
that the walking belt has
The console features a dis-
play demo mode, designed
to be used if the treadmill is
displayed in a store. While
moved, for a few seconds each.
the demo mode is turned
on, the console will function
To exit the information mode, remove the key from the
console.
normally when you plug in the power cord, press the
power switch into the reset position, and insert the key
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
HOW TO MOVE THE TREADMILL
Before folding the treadmill, adjust the incline to
the lowest position. If you do not do this, you may
damage the treadmill when you fold it. Remove the
key and unplug the power cord. CAUTION: You must
be able to safely lift 45 lbs. (20 kg) to raise, lower, or
move the treadmill.
Before moving the treadmill, fold it as described at the
left. CAUTION: Make sure that the catch is resting
against the latch pin. Moving the treadmill may re-
quire two people.
1. Hold the frame and one of the handrails, and place
one foot against a wheel.
1. Hold the metal frame firmly in the location shown
by the arrow below. CAUTION: Do not hold the
frame by the plastic foot rails. Bend your legs
and keep your back straight. Raise the frame
about halfway to the vertical position.
1
Frame
1
Handrail
Wheel
Frame
2. Hold the treadmill firmly with your right hand as
shown. Pull the latch knob to the left and hold it.
Raise the frame until the catch is past the latch pin.
Then, slowly release the latch knob; make sure
that the catch is resting against the latch pin.
2. Pull back on the handrail until the treadmill will roll
on the wheels, and carefully move it to the desired
location. CAUTION: Do not move the treadmill
without tipping it back, do not pull on the frame,
and do not move the treadmill over an uneven
surface.
2
3. Place one foot against a wheel, and carefully lower
the treadmill.
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2. Hold the upper end of the treadmill
with your right hand as shown. Pull the latch knob
to the left and hold it. Next, lower the frame until it
is past the latch pin. Then, release the latch knob.
Latch
Pin
Latch
Knob
Catch
2. See drawing 1 at the left. Hold the metal frame
firmly with both hands, and lower it to the floor.
CAUTION: Do not hold the frame by the plastic
foot rails, and do not drop the frame. Bend your
legs and keep your back straight.
To protect the floor or carpet, place a mat under the
treadmill. Keep the treadmill out of direct sunlight.
Do not leave the treadmill in the storage position in
temperatures above 85° F (30° C).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 9. IMPORTANT: The treadmill is not com-
patible with GFCI-equipped outlets and may not be compatible with AFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the power switch located on the treadmill
c
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
switch, wait for five minutes and then press the
Tripped
Reset
switch back in.
PROBLEM: The power turns off during use
SOLUTION: a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes
and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 14 to turn off the demo mode.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Place the treadmill in the
storage position (see HOW TO FOLD THE TREADMILL on page 15).
Remove the six indicated M4.2 x 13mm Washer Head
Screws (5) and the six Foot Rail Flat Washers (25).
50
Next, lower the Frame (50) (see HOW TO LOWER
THE TREADMILL FOR USE on page 15).
5
5
25
25
5
5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the five indicated M4.2 x 19mm Washer Head
Screws (9). Then, carefully remove the Motor Hood
(56).
9
56
9
9
Locate the Reed Switch (42) and the Magnet (44) on
the left side of the Pulley (46). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8 in. (3 mm). If necessary, loosen
the M4.2 x 13mm Tek Screw (7), move the Reed
Switch slightly, and then retighten the Screw. Reattach
the Motor Hood (not shown), and run the treadmill for
a few minutes to check for a correct speed reading.
1/8 in.
7
46
44
42
Top View
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.
b. If the walking belt is overtightened, treadmill perfor-
b
2–3 in.
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both idler
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to 7
cm) off the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
Idler Roller
Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn the left idler roller bolt clock-
wise 1/2 of a turn. Be careful not to overtighten the
walking belt. If the walking belt has shifted to the
right, turn the left idler roller bolt counterclockwise 1/2
of a turn. Then, plug in the power cord, insert the key,
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
a
b
b. If the walking belt slips when walked on, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both idler roller bolts clock-
wise, 1/4 of a turn. When the walking belt is correctly
tightened, you should be able to lift each edge of the
walking belt 2 to 3 in. (5 to 7 cm) off the walking plat-
form. Be careful to keep the walking belt centered.
Then, plug in the power cord, insert the key, and care-
fully walk on the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, reinsert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning any
exercise program, consult your physician.
This is especially important for persons over
age 35 or persons with pre-existing health
problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is in-
tended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exer-
cise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic ex-
ercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretch-
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST
Model No. WLTL39810.0 R0211A
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
4
4
21
2
18
6
1
4
5
1
7
4
4
2
2
1
2
2
2
2
2
2
4
2
14
4
2
2
6
1
1
4
3
1
1
1
1
1
1
2
2
1
1
1
1
1
M10 x 65mm Patch Screw
M10 x 45mm Screw
M4.2 x 19mm Screw
M8 x 35mm Screw
M4.2 x 13mm Washer Head Screw
M4.2 x 13mm Screw
M4.2 x 13mm Tek Screw
M4.2 x 19mm Tek Screw
M4.2 x 19mm Washer Head Screw
M4.2 x 13mm Bright Screw
M4 x 10mm Screw
M8 x 30mm Bolt
M4.2 x 13mm Indented Screw
M6 x 70mm Screw
1/4" Motor Bolt
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
*
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
4
1
1
4
2
1
1
1
1
1
3
4
2
4
2
1
1
2
2
1
1
2
2
1
1
2
4
–
Walking Belt
Walking Platform
Right Foot Rail
Frame
2
3
4
5
Right Idler Roller Bracket
Incline Motor
Incline Frame
Idler Roller
6
7
8
9
Left Idler Roller Bracket
Motor Hood
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Drive Motor Bracket
Drive Motor
Electronics Bracket
Controller
Belly Pan
M8 x 102mm Bolt
M8 x 20mm Bolt
3/8" x 2" Bolt
Power Switch
Grommet
Power Cord
8" Tie
M10 x 58mm Screw
M10 x 110mm Screw
5/16" Nut
Releasable Wire Tie
Console Base
Handrail Cap
Handrail
M8.4 Star Washer
M4.2 Star Washer
Roller Spacer
Console
Foot Rail Flat Washer
#8 Flat Washer
Upright Wire
Latch Housing
Upright
M10 Star Washer
M10 Flat Washer
M8 Flange Nut
Key/Clip
Wire Tie
Right Rear Foot
Frame Spacer
Base Cap
M8 Nut
3/8" Locknut
Base Pad
#8 Hood Clip
Wheel
Left Rear Foot
Base
6 mm Hex Key
Upright Grommet
Mount
4 mm Hex Key
Left Foot Rail
#10 x 1" Tek Screw
Latch Pin Assembly
Gas Spring
Latch Warning Decal
Catch
Platform Cushion
Belt Guide
Spring Clip
Caution Decal
3/8" x 1 1/4" Bolt
3/8" x 1 3/4" Bolt
1/4" Flat Washer
M6 Star Washer
Userʼs Manual
Reed Switch
Reed Switch Clamp
Magnet
Drive Belt
Drive Roller/Pulley
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A
Model No. WLTL39810.0 R0211A
5
0
1
5
4
2
1
4
6
1
3
1
2
1
5
4
1
3
3
5
0
4
6
4
9
4
4
4
7
4
2
2
4
1
8
4
3
0
1
5
1
1
9
4
5
2
4
2
1
3
3
2
5
3
3
0
4
7
3
6
3
5
3
21
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B
Model No. WLTL39810.0 R0211A
9
56
9
33
9
9
33
33
17
15
22
9
29
22
17
57
58
89
11
23
11
19
32
88
11
52
23
11
53
59
32
60
19
61
62
64
63
11
65
66
63
22
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING C
Model No. WLTL39810.0 R0211A
67
68
70
69
2
3
6
3
6
68
6
6
3
71
69
68
2
74
3
3
3
72
68
83
20
84
73
75
28
76
27
77
87
78
80
8
76
81
71
1
18
27
28
20
77
82
11
32
78
8
87
21
78
85
79
8
1
21
32
79
78
8
86
82
18
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
vide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
Part No. 308586 R0211A
Printed in China © 2011 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|