Brother Label Maker PT2430PC User Manual

International ENERGY STAR® Compliance Statement  
The purpose of the International ENERGY STAR® Program is to  
promote the development and popularization of energy-efcient of-  
ce equipment.  
Printed in China  
LB0000000 A  
English  
As an ENERGY STAR® Partner, Brother Industries, Ltd. has deter-  
mined that this product meets the ENERGY STAR® guidelines for  
energy efciency.  
USER’S GUIDE  
INTRODUCTION  
Thank you for choosing the PT-2430PC. Your new P-touch labeler uses P-touch Editor Lite software, which is already installed on your labeler.  
There is no need to install any software or drivers onto your PC in order to make creative labels. This manual includes important precautionary  
information and simple instructions for operating your new P-touch labeler. Be sure to read the instructions before use and use the product in ac-  
cordance with these instructions. Keep this manual handy for future reference.  
SAFETY PRECAUTIONS  
WARNING  
• Always use the specied voltage and the included AC adapter (AD-24ES) for this machine to prevent any damage or failure.  
• Unplug the power cord immediately and stop using the P-touch labeler during an electrical storm. There may be a remote risk of electric shock from lightning.  
• Do not use the AC adapter in places of high humidity such as bathrooms.  
• Do not overload the power cord.  
• Do not place heavy objects on, or damage the power cord or plug. Do not forcibly bend or pull the power cord. When disconnecting the power cord from the power outlet, al-  
ways hold the plug.  
To prevent re or electric shock, make sure that the plug is fully inserted to the power outlet. Do not use an outlet that is loose.  
• Do not get the machine/AC adapter/power plug wet, such as by handling them with wet hands or spilling beverages on to them.  
• Do not disassemble or modify P-touch labeler/AC adapter/batteries.  
• Do not use metallic articles, such as tweezers or a metallic pen, when exchanging the batteries.  
• Do not throw into re or heat up the battery.  
Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)  
Responsible Party: Brother International Corporation 100 Somerset Corporate Boulevard Bridgewater, NJ 08807-0911 USA  
TEL: (908) 704-1700  
• Disconnect the AC adapter, remove batteries and stop using immediately if you notice any abnormal odor, heat, discoloration, deformation or anything unusual while in use, or  
in storage.  
declares that the product: Product Name: P-touch Labeler PT-2430PC  
Model Number: PT-2430PC  
CAUTION  
To avoid injuries, do not touch the blade of the cutter unit or any metal parts near the print head.  
• Remove the batteries and disconnect the AC adapter if you do not intend to use P-touch labeler for an extended period of time.  
• Do not use old and new batteries together or mix alkaline batteries with other type batteries, or set the positive and negative end in the wrong position. Otherwise, the batter-  
ies may leak or be damaged.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful  
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  
To prevent damage or breakage, do not drop or hit P-touch labeler/AC adapter.  
• Use only the USB cable included with the P-touch labeler.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and  
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to cor-  
rect the interference by one or more of the following measures:  
General Precautions  
• Depending on the location, material, and environmental conditions, the label may unpeel or become irremovable, the color of the label may change or be transferred to other  
objects. Before applying the label, check the environmental condition and the material.  
• Do not use the P-touch labeler in any way or for any purpose not described in this guide. Doing so may result in accidents or damage the machine.  
• Use only Brother TZ tapes with this machine. Do not use tapes that do not have the  
• Do not clean P-touch labeler with alcohol or other organic solvents. Only use a soft, dry cloth.  
• Do not touch the print head with your ngers anytime to prevent from a burn. Use a soft wipe (e.g. a cotton swab) when cleaning the print head.  
• Do not put any foreign objects into the tape exit slot or AC adapter connector, etc.  
• Do not place the P-touch labeler/battery in direct sunlight or rain, near heaters or other hot appliances, in any location exposed to extremely high or low temperatures (e.g. on  
the dashboard or in the back of your car), high humidity, or dusty locations.  
mark.  
-
-
-
-
-
-
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modications not expressly approved by Brother Industries, Ltd. could void the user’s authority to operate the equipment.  
The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital device.  
• Do not try to print labels using an empty tape cassette in the P-touch labeler. Doing so will damage the print head.  
• Do not pull the tape being fed from the P-touch labeler, otherwise the tape cassette or P-touch labeler may be damaged.  
Getting Ready  
Review the names of P-touch labeler parts.  
Install a tape cassette.  
Feed & Cut button  
LED lamp  
Power  
Open the cassette  
cover.  
Insert a tape  
cassette.  
Close the cassette  
cover.  
Release Lever  
Print head  
button  
Tape exit slot  
Tape cutter  
AC adapter (included)  
connecter  
USB port  
Mode selector  
switch  
Verify that the P-touch labeler is  
turned off. Open the cassette cover  
as shown by the arrow in the above  
illustration while pressing the part  
marked "<<".  
Insert a tape cassette as shown in  
the above illustration.  
Make sure that the end of the tape feeds under the tape guides.  
The PT-2430PC has 2 mode selector settings - “EL” and “E”. The mode selector  
switch is pre-set at the factory to the EL mode, for use with P-touch Editor Lite. For  
E mode, you will need to install P-touch Editor 5.0, a more advanced labeling soft-  
ware, and the required drivers from the enclosed CD. For details on how to install  
the P-touch Editor 5.0, see “Starting P-touch Editor 5.0” below.  
• If the ink ribbon is loose, use your nger to wind the toothed  
wheel in the direction of the arrow on the cassette.  
• Use only Brother tapes with the P-touch labeler.  
• For initial use of the tape, install the tape. Then, push in the feed  
and cut button to cut the tape.  
Make sure that the release lever is up when closing the tape cover.  
The tape cover cannot be closed if the release lever is pressed down.  
Auto Power Off Function  
Connect the P-touch labeler's power supply.  
When using the P-touch labeler with  
batteries, insert six new AA alkaline  
batteries (LR6), making sure that  
their poles point in the correct direc-  
tions. Always replace all six batter-  
ies at the same time using brand  
new ones.  
When the P-touch labeler is operating on battery power only,  
it will turn off automatically if not used for a period of 20 min-  
utes. The message “Unsafe Removal of Device” may be  
displayed depending on the Operating System running on  
your PC. Any data being displayed will be saved. When you  
turn the labeler back on, click on the Editor Lite icon to re-  
sume creating your label.  
When using the included AC adapter (AD-  
24ES), insert the plug on the adapter cord  
into the adapter jack on the bottom end of the  
P-touch labeler. Insert the plug into the near-  
est standard electrical outlet.  
Connect the USB cable and start P-touch Editor Lite.  
P-touch Editor Lite  
starts immediately.  
Windows® 2000 User  
For details on using  
P-touch Editor Lite,  
see the back of this  
sheet.  
Go to My Computer and open Removable Disk, then  
start P-touch Editor Lite by double-clicking PTLITE10.  
EXE.  
Connect the  
USB cable.  
Turn on the P-touch labeler.  
The LED lamp will light up.  
Windows® XP User  
Do not turn off the power or remove the labeler while  
using P-touch Editor Lite.  
It will take longer than usu-  
al to start P-touch Editor  
Pop-up Window  
Appears. Select  
P-touch Editor  
Lite and click OK.  
Lite when connecting P-touch  
labeler to your computer for the  
first time. If the software does  
not start automatically when you  
connect the machine, you may  
launch it from My Computer.  
Start P-touch Editor Lite by dou-  
When using  
Windows Vista®  
Windows Vista® User  
When connecting the device for the rst time, perform the  
scan and then select the Always do this for software and  
games check box on the dialog box displayed when the  
scan completes. P-touch Editor Lite will start automatically  
the next time you connect the P-touch labeler.  
ble-clicking  
PTLITE10.EXE.  
Pop-up Window  
Appears. Click  
P-touch Editor  
Lite.  
*Microsoft Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and other  
countries.  
How to disconnect the P-touch  
labeler  
*The name of other software or products used in this document are trademarks or registered trademarks of the respective  
companies that developed them.  
Exit P-touch Editor Lite by clicking on the at the top  
right.  
Starting P-touch Editor 5.0  
To disconnect the labeler, click the icon in the computer’s  
task bar ( , , or ).  
Click Safely remove USB Mass Storage Device.  
If you would like to use the more advanced software that is available for your P-touch labeler,  
you are able to install P-touch Editor 5.0 from the included CD-ROM. This advanced software  
will give you greater label making functionality.  
Do not connect the P-touch labeler to your PC before you begin the P-touch Edi-  
tor 5.0 installation. For details on how to install P-touch Editor 5.0, see the in-  
stallation guide in the included CD-ROM.  
Move the mode selec-  
tor switch on the back  
of the P-touch labeler  
to the “E” position be-  
fore connecting the  
USB cable.  
When The device can be safely removed is displayed,  
turn off the P-touch labeler and disconnect the USB ca-  
ble.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bertazzoni Cooktop CB36500X User Manual
Black Box Network Hardware LGB5128A User Manual
Black Box Network Hardware LWE100A User Manual
Black Decker Coffeemaker DCM3100B User Manual
Brocade Communications Systems Switch VA 40FC User Manual
Campbell Hausfeld Nail Gun IN170305AV User Manual
Canon Camera Lens 1257B002 User Manual
Carrier Heating System 48PG20 28 User Manual
Casio Electronic Keyboard LK230ES1A User Manual
Chevrolet Automobile 2011 Corvette Coupe User Manual