Briggs Stratton Lawn Mower 1695354 User Manual

OPERATOR’S  
MANUAL  
Turboless Triple Catcher  
Turboless Triple Catcher  
Mfg. No.  
1695354  
Description  
44” & 50” Turboless Triple Catcher  
CAUTION: Read and  
follow all instructions.  
Manual Part No. 1734740  
Revision 01  
Rev. Date 05/2007  
TP 100-4527-01-AT-SMAN  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Mowing with the Catcher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Storing the Catcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Install Mounting Plates & Spacers (Broadmoor/1600/2600/LT Series) . . . . 5  
Install Mounting Spacers (Conquest/1700/2700/YT  
& Prestige/1800/2800/GT Series . . . . . . . . . . . . 5  
Remove Blowout Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Install Baffles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Install Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Install Bag and Cover Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Install Hitch and Upright Support Assembly . . . . . . . . . . . . . . . . . . . . . . . 10  
Install Cover Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Install Collector Bags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Install Lower Discharge Chute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Install Upper Tube to Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Install Middle Tube. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Normal Removal & Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
GENERAL WARNINGS  
• Know the unit’s controls and how to stop quickly.  
READ THE OPERATOR’S MANUALS.  
periodically for tears, holes, or weak spots and  
replace with a new bag that meets manufacturer’s  
durability standards.  
• Read and obey all safety decals.  
• Only allow responsible adults, who are familiar with  
the instructions, to operate the unit.  
• Disengage the PTO. Shut off the engine and wait  
for all moving parts to stop before attaching,  
adjusting, or disconnecting any part of the  
collection system.  
• If the mower stalls or the collector chute plugs:  
1. Disengage the PTO;  
2. Stop the engine and remove the key;  
3. Set the parking brake, and wait for all moving  
parts to stop.  
4. Remove the foreign object or clear the chute  
with a piece of wood before restarting the engine.  
NEVER place hands into COLLECTOR OR  
MOWER housing to clear jammed objects.  
Blower OR MOWER may rotate when object is  
removed.  
• Check the collection system to make sure it is  
bolted tightly to the unit.  
• DO NOT operate the unit without either the entire  
grass catcher or the deflector in place.  
Turn off the PTO to disengage the blades when not  
mowing.  
• DO NOT mow in reverse unless absolutely  
necessary. Always look down and behind before  
and while travelling in reverse.  
• DO NOT turn sharply when travelling alongside a  
building or any object. Slow down before turning.  
• DO NOT carry passengers.  
• When collection system is removed from the  
mower deck, the deflector must be properly  
installed.  
• For added stability and to prevent tipping or loss of  
control:  
a. Use reduced speed on uneven ground and  
when turning corners.  
b. Reduce loads on hillsides. It is recommended  
that the collection system be kept only half full  
when negotiating any slopes. Start mowing on  
slopes when the collection system is empty.  
c. Mow up and down the face of slopes; never  
across the face of any slope.  
• Collector bags are subject to deterioration and  
wear during normal use. Inspect the bag  
Never operate on slopes greater than 17.6%  
(10°).  
SAFETY DECALS  
These labels are easily applied and will act as a  
constant visual reminder to you, and others who may  
use the equipment, to follow the safety instructions  
necessary for safe, effective operation.  
This unit has been designed and manufactured to  
provide you with the safety and reliability you would  
expect from an industry leader in outdoor power  
equipment manufacturing.  
Attachment Decal  
Although reading this manual and the safety  
instructions it contains will provide you with the  
necessary basic knowledge to operate this equipment  
safely and effectively, we have placed several safety  
labels on the unit to remind you of this important  
information while you are operating your unit.  
WARNING  
Thrown objects hazard  
• Objects thrown by the mower can seriously  
injure or kill you.  
• Do not open the hopper while the mower blades  
are turning.  
All DANGER, WARNING, CAUTION and  
instructional messages on your rider, attachments  
and mower should be carefully read and obeyed.  
Personal bodily injury can result when these  
instructions are not followed. The information is for  
your safety and it is important! The safety decals  
below are on your product.  
• Do not operate the mower without the complete  
catcher in place.  
1732819  
Decal - WARNING Thrown  
Objects Hazard  
Part Number 1732819  
If any decals are lost or damaged, replace them at  
once. See your local dealer for replacements.  
Read and obey all operation and warning decals.  
TP 600-2562-01-AT-SMA  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Operation  
Clear the lawn of all sticks, stones, wire and other  
debris which may be caught or thrown by the mower  
blades.  
Check grass condition. If wet, wait until later in the  
day. If grass is wet, the grass catcher is likely to  
become plugged.  
For efficient bagging, air circulation under the  
mower deck, through the chute and into the bag  
is very important.  
For this reason, BEFORE YOU BEGIN MOWING you  
should make certain the underside of the mower and  
the underside of the catcher lid are free from grass  
and debris.  
Make sure that there is a snug fit between mower  
deck, blower housing, tubes, and grass catcher cover.  
Mowing with the Catcher  
Always operate with throttle at full speed when  
mowing.  
CAUTION  
Before you begin operating the unit be certain  
you have read all of the safety and operational  
information of this instruction sheet, as well as  
the Operator’s Manual for the tractor and any  
other attachments.  
Grass should be cut often, and not too short. If grass  
is too long or lush it may be necessary to keep  
ground speed to a minimum or to cut only half the  
width of the mower to prevent clogging. If grass is  
long, operate with mower in high cutting position for  
first pass, cutting again in a lower position on a  
second pass.  
Never operate on slopes greater than 17.6% (10°).  
Do not open the cover with mower engaged.  
After Operation  
Remove any debris from the the screen on the  
underside of the lid.  
If a large amount of cut grass is spilling out from  
under deck, the tube may be plugged or the bags  
may be full— discontinue mowing, stop the unit,  
disengage the PTO, shut off the engine and then  
empty the catcher or clear the tube.  
The blower housing and tube should be removed for  
cleaning.  
Inspect the grass bags for wear or damage. Make  
sure that there is a snug fit between mower deck,  
blower housing, tubes, and grass catcher cover.  
WARNING  
ALWAYS shut off the tractor. Disengage the  
PTO, and allow all moving parts to stop  
BEFORE disconnecting or clearing tube, or  
emptying catcher.  
Storing The Grass Catcher  
Clean the grass catcher thoroughly using a mild  
detergent (other products may damage the tube).  
Remove any debris from the screen on the underside  
of the lid.  
Before leaving the operator’s position for any  
reason, engage the parking brake, disengage  
the PTO, stop the engine and remove the key.  
If paint has been scratched on metal parts, touch up  
with paint, or apply a thin film of oil to prevent  
corrosion.  
To reduce fire hazard, keep the engine, rider  
and mower free of grass, leaves and excess  
grease. Do not stop or park rider over dry  
leaves, grass or combustible materials.  
Store in a dry area. Dry thoroughly before storing for  
a long period of time. Always store away from  
moisture.  
CAUTION  
Do not leave grass in bagger containers.  
Empty containers after each use and before  
storing. Failure to do so may result in  
spontaneous combustion which could develop  
into a fire.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
INSTALL MOUNTING PLATES -  
BROADMOOR / 1600 / 2600 / LT  
SERIES  
A
B
C
D
Install Plates & Spacers  
1. Mount the side brackets (C, Figure 1) to both  
sides of the frame using the holes shown. Secure  
with one 3/8-16 x 1 capscrew (D), 3/8 lockwasher  
(B), and 3/8-16 nut (A) per side.  
Figure 1. Install Side Brackets  
A. Nut, 3/8-16  
B. Lockwasher, 3/8  
C. Side Bracket  
2. Install the rear spacers (C, Figure 2). Secure with  
two 1/2-13 x 2-1/2 capscrews (E), washers (D),  
spacers (C), and 1/2-13 nylock nuts (A) per side.  
D. Capscrew, 3/8-16 x 1  
A
C
D
D
B
Figure 2. Install Rear Spacers  
A. Nylock Nuts, 1/2-13  
B. Capscrew, 1/2-13 x 2-1/2  
C. Spacers  
D. Washers, 1/2  
INSTALL MOUNTING SPACERS -  
CONQUEST / 1700 / 2700 / YT &  
PRESTIGE / 1800 / 2800 / GT  
SERIES  
A
C
D
Install Spacers  
1. Install the rear spacers (C, Figure 3). Secure with  
two 1/2-13 x 2-1/2 capscrews (E), washers (D),  
spacers (C), and 1/2-13 nylock nuts (A) per side.  
B
D
Figure 3. Install Rear Spacers  
A. Nylock Nuts, 1/2-13  
B. Capscrews, 1/2-13 x 2-1/2  
C. Spacers  
D. Washers, 1/2  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remove Blowout Baffle  
Install Baffles  
1.Remove and discard short blowout baffle (C, Figure  
4), carriage bolts (B) and locknuts (D) from mower  
deck (A).  
1. Determine which baffle to use. See Figure 5  
Chart.  
2. Lift side discharge chute (H, Figure 6).  
3. Insert baffle (F) through discharge opening and  
position baffle into place.  
4. Tighten carriage bolts (A) and nuts (E) on baffle  
(F).  
5. Tighten carriage bolt (B) and nut (E) on baffle (F).  
6. Position baffle (G) into place.  
B
D
7. Tighten carriage bolts (C) and nuts (E) on baffle  
(G).  
A
D
8. Tighten carriage bolts (D) and nuts (E) on baffle  
(G).  
C
44” Mower Deck  
50” Mower Deck  
Figure 4. Baffle Removal  
A. Mower Deck  
B. Carriage Bolts,5/16-18 x 3/4  
C. Blowout Baffle, Short  
D. Nuts, Whizlock, 5/16-18 x 3/4  
“A” RH side 26-1/4” long RH side 29-3/4” long  
“B” LH side 24-7/8” long LH side 27-3/4” long  
“A”  
“B”  
Figure 5. Baffle Chart  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
H
E
A
A. Carriage Bolts,  
5/16-18 x 5/8  
B. Carriage Bolt,  
5/16-18 x 5/8  
E
E
C. Carriage Bolts,  
5/16-18 x 5/8  
C
F
D. Carriage Bolts,  
5/16-18 x 5/8  
E
B
D
E
E. Locknut, 5/16-18  
F. Right Hand Baffle  
G. Left Hand Baffle  
H. Discharge Chute  
G
Figure 6. Install Baffles  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALL LOWER CHUTE ROD AND PIN TO BOOT  
Install Components  
INSTALL MOUNTING PLATE  
1. Insert the head of pin (A, Figure 8) through front  
hole of lower chute (D). Secure with 1/4-20 x 5/8  
carriage bolt (B) and 1/4-20 lock nut (C) as  
shown.  
1. Install mounting plate (A, Figure 7) to mower deck  
as shown. Secure with 5/16-18 x 5/8 carriage  
bolts (C) and 5/16-18 locknuts (A).  
2. Install the rod (H) to lower chute (D) using 5/16-18  
x 1 capscrew (J) and 5/16-18 locknut (G) for front  
holes. Use 5/16-18 x 1-1/4 capscrew (I) and 5/16-  
18 locknut (G) as shown. Tighten hardware.  
3. Install the rubber strap (F) onto capscrew (I)  
securing with 5/16-18 locknut as shown.  
A
C
C
B
B
A
D
E
F
G
Figure 7. Install Mounting Plate  
A. Mounting Plate  
G
B. Locknuts, 5/16-18  
C. Carriage Bolts, 5/16-18 x 5/8  
H
J
I
Figure 8. Install Lower Chute and Pin to Boot  
A. Pin, Latch  
B. Carriage Bolt, 1/4-20 x 5/8  
C. Locknut, 1/4-20  
D. Lower Chute  
E. Locknut, Center Lock, 5/16-18  
F. Strap, Rubber  
G. Locknuts, Whiz Lock, 5/16-18  
H. Rod, Boot Mount  
I. Capscrew, Hex Head, 5/16-18 x 1-1/4  
J. Capscrew, Hex Head, Thin, 5/16-18 x 1  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALL HANDLE TO TUBE  
1. Install handle (A, Figure 9) using 1/4-20 x 1/2  
screw and 1/4-20 locknut (B) for rear hole. Use  
1/4-20 x 1 screw (D) as shown. Tighten hardware.  
2. Install strap (E) to screw (D) securing with 1/4-20  
locknut (F).  
F
B
A
E
C
B
D
Figure 9. Install Handle to Tube  
A. Handle  
B. Locknuts, KEPS, 1/4-20  
C. Screw, Slotted, 1/4-20 x 1/2  
D. Screw, Slotted, 1/4-20 x 1  
E. Strap, Rubber  
F. Locknut, Center Lock, 1/4-20  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALL BAG AND COVER SUPPORT  
INSTALL COVER ASSEMBLY  
1. Install the bag and cover support (B, Figure 10) to  
upright support (A) using reinforcement plate (C)  
and 3/8-16 x 1 capscrews (D) and 3/8-16 locknuts  
(E) as shown.  
1. Attach cover assembly (B, Figure 12) to bag  
support bracket (A) using hinge pivots (E). Secure  
cover using cover hinge pins (C) and hair pins (D)  
as shown.  
B
B
E
C
D
E
D
A
A
C
D
E
C
Figure 10. Install Bag and Cover Support  
A. Upright Support  
B. Bag and cover Support  
C. Reinforcement Plate  
D. Capscrews, 3/8-16 x 1  
E. Locknuts, 3/8-16  
Figure 12. Install Cover Assembly  
A. Bag Support Bracket  
B. Cover Assembly  
C. Cover Hinge Pins  
D. Hair Pins  
E. Hinge Pivots  
INSTALL HITCH AND UPRIGHT SUPPORT ASSEMBLY  
1. Attach hitch and upright support assembly (A,  
Figure 11) to frame spacers (B) as shown.  
A
B
B
Figure 11. Attach Hitch and Upright Support  
A. Hitch and Upright Support Assembly  
B. Frame spacers  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALL COLLECTOR BAGS  
INSTALL LOWER DISCHARGE CHUTE  
1. Raise the cover (A, Figure 13).  
1.Lift discharge deflector up (D, Figure 14).  
2. Insert lower chute rod (A) into mounting plate (B).  
2. Attach collector bags (B) using grass bag hanger  
(C) to bag hanger post (D).  
3. Pull rubber strap (C) and secure by placing hole  
closest to knob in strap completely over locknut  
(E).  
A
C
D
C
E
D
A
B
B
Figure 13. Install Collector Bags  
A. Cover  
B. Collector Bag  
C. Grass Bag Hanger  
D. Bag Hanger Posts  
Figure 14. Install Lower Discharge Chute  
A. Lower Chute Rod  
B. Mounting Plate  
C. Rubber Strap  
D. Discharge Deflector  
E. Locknut  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
44” Frame Hung Mowers  
50” Frame Hung Mowers  
44” Free Floating Mowers  
D
50” Free Floating Mowers  
C
E
D
F
B
B
A
C
Figure 15. Install Upper Tube to Cover  
A. Upper Tube  
B. Cover  
C. Ridge, Upper Tube  
D. Ridge Cutout  
A
INSTALLING UPPER & MIDDLE TUBES  
Figure 16. Install Middle Tube  
A. Lower Chute  
B. Strap, Rubber  
C. Pin  
D. Middle Tube  
E. Upper Tube  
1. Slide the upper tube (E, Figure 15) into cover (B)  
aligning ridge (C) with cutout (D) as shown.  
2. See Figure 16 for correct hole location and secure  
the upper tube (E) to middle tube using screw (F).  
F. Screw, 1/4 x 3/4  
2. Slide middle tube (D, Figure 16) into upper tube  
(E).  
3. Slide middle tube (D) over boot (A). Pull strap (B)  
and place hole completely over pin (C).  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Normal Removal & Installation  
E
F
R
Q
D
C
D
G
A
B
C
S
P
H
O
S
A. Hitch Support Assembly  
B. Cover  
C. Pin  
D. Hair Pins  
E. Bag  
F. Grass Bag Hanger  
G. Upper Tube  
H. Middle Tube  
I. Strap, Boot  
J. Deflector  
J
N
I
K. Nut & Capscrew  
L. Mounting plate  
M. Lower Chute Rod  
N. Lower Chute  
O. Pin  
P. Strap, Middle  
Q. Ridge  
R. Ridge Cutout  
S. Rear Spacers  
K
M
L
Figure 17. Normal Installation & Removal  
4. Lift discharge deflector (J) up. Insert lower chute  
rod (M) into mounting plate (L). Pull strap (I) and  
secure by placing hole closest to knob in strap  
completely over locknut and capscrew (K).  
Normal Removal & Installation  
Collector Installation  
Note: See previous pages for more detailed  
5. Slide the upper tube (G) into cover (B) aligning  
ridge (Q) with cutout (R) as shown.  
installation and operation instructions if necessary.  
1. Mount the hitch support assembly (A, Figure 17)  
onto rear tractor frame spacers (S).  
6. Slide middle tube (H) into upper tube (G). Slide  
middle tube (H) over lower chute (N). Pull strap  
(P) and place hole completely over pin (O).  
2. Attach cover (B) to support assembly using pins  
(C) and hair pins(D).  
3. Pivot cover (B) up. Install bags (E) by attaching  
grass bag hanger (F) to support assembly (A).  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Collector Removal  
WARNING  
OPERATION WITHOUT BAGGER  
For operation without bagger, the mower  
deflector MUST be properly installed in the  
down position and retained by the spring latch.  
1. Unhook strap (P, Figure 17) from pin (O). Slide  
middle tube (H) into upper tube (G) and remove  
middle tube (H). Remove upper tube (G) from  
cover (B).  
2. Lift up cover (B) remove and empty bags (E).  
3. Unhook strap (I) from locknut and capscrew (K).  
Remove lower chute (N) from mounting plate (L).  
See that the discharge deflector (J) returns to the  
DOWN position.  
4. Remove hair pin (D) and pins (C) then remove  
cover (B).  
Note: To prevent loss of parts, reinstall pins (C) and  
hair pins (D) in support assembly hinge pivots (E,  
Figure 17).  
5. Remove hitch support assembly (A) from rear  
frame spacers (S).  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MANUFACTURING, INC.  
500 N Spring Street / PO Box 997  
Port Washington, WI 53074-0997  
PRODUCTS  
535 Macon Street  
McDonough, GA 30253  
500 N Spring Street / PO Box 997  
Port Washington, WI 53074-0997  
500 N Spring Street / PO Box 997  
Port Washington, WI 53074-0997  
AGCOLawn.com  
Briggs & Stratton Yard Power Products Group  
Copyright © 2007 Briggs & Stratton Corporation  
Milwaukee, WI USA. All Rights Reserved  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bosch Appliances Cooktop PCL 785 FAU User Manual
Boss Audio Systems MP3 Player MR1305WUA User Manual
Braun Electric Shaver 320S 4 User Manual
Briggs Stratton Pressure Washer 020261 0 User Manual
Brinly Hardy Lawn Mower Accessory hdc 10 User Manual
Broan Ventilation Hood QL1 Series User Manual
Cables to Go Network Router CDM 570 User Manual
Cadillac Automobile 2009 XLR User Manual
Cannon Fishing Equipment MAG 10HS User Manual
Carson Optical Microscope Magnifier vm 10 User Manual