CAUTION:
READ THIS MANUAL CAREFULLY
BEFORE OPERATING YOUR NEW
CANNON® DOWNRIGGER.
RETAIN FOR FUTURE REFERENCE.
MAG 10HS
MAG 10TS
NOTE: Do not return your CANNON® Downrigger to your
retailer. Your retailer is not authorized to repair or replace
this unit. You may obtain service by:
•
•
calling CANNON® at 1-800-227-6433;
returning your downrigger to the Factory Service
Center;
•
sending or taking your downrigger to any CANNON®
Authorized Service Center on enclosed list.
MAG 5HS
Please include proof of purchase, serial number and
purchase date for warranty service with any of the
above options.
OWNER’S MANUAL
Introduction to Downriggers
Mounting Your Downrigger
Terminator & Line Release
Cannon Uni-Release
pg. 2
pg. 2-6
pg. 7
Maintaining Your Downrigger
Positive Ion Control
The Effects of Blowback
Troubleshooting
pg. 11
pg. 12
pg. 12-13
pg. 13
pg. 7
Attaching the Rod Holder
Wiring Your Downrigger
Operating Your Downrigger
The Short Stop System
pg. 8
pg. 9
pg. 10-11
pg. 11
Trolling Tips
pg. 14
pg. 15
pg. 15
See List
Warranty Information
Cannon Service Policy
Authorized Service Centers
Download from Www.Somanuals.com. All Manuals Search And Download.
Downrigger Mounting on Boats
A downrigger should be mounted where ever it
is easy to operate and observe. You want to be
able to see your fishing rod and to react quickly.
So, choosing a good spot to mount your
downrigger on your boat is 99% of the job.
Due to the great variety of boats available,
mounting your downrigger can be a dilemma.
Having proper mounting accessories is essential.
Cannon has a complete line of mounting
accessories to conveniently mount your
downriggers on any boat.
Arrows
Indicate
Mounting
Locations
Mounting Accessories
Deck Plate
Deck Plates are necessary when extra
strength must be added to the base material of
the boat and for attaching the downrigger to other
mounting accessories.
Gimbal Mounts are designed to fit medium-
sized flush mounted rod holders built into the
gunwale of many larger fishing boats and
cruisers. Only sturdy, high quality rod holders
should be used for this temporary mounting
system. Gimbal mounts are available in 9” or 12”
post lengths.
Gimbal Mount
Clamp Mounts can be mounted at the
junction of two rail sections with the aid of two ¼"
pieces of plywood. They will protect your rail from
any marks from the clamp and provide a non-slip
urface.
Clamp Mount
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Side Rail Mounting
Side/Rail on T-Section
Side/Rail mounts can be mounted to a
welded T-section. It can also be used at the two
rail section butt joint. In both installations it is
recommended to use a non-slip material, such
as rubber or a thin wood sheet, between metal
surfaces.
You can also use these for mounting to a very
narrow side gunwale. There is a plate provided
for back-up with bolts and washers. If the
gunwale compartment is foamed in, then
wellnuts should be used. It is also recommended
to install two additional flat head screws through
the top plate for stabilization (you will need to
drill and countersink).
Side/Rail on Gunwale
NOTE: In no case should this mount be used
on fiberglass ¼" thick or less unless it is
foamed in.
Pedestal Mounting
Pedestals are used wherever additional height is
needed for ease of operation or to clear
obstructions, such as handrails.
Pedestal for Additional Height
Caution: When using a pedestal mount
or side/rail mount, do not extend the
telescopic boom on your Mag 10 HS \
Mag 10 TS. The increased leverage
will cause excessive strain and
possible failure of the mount.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Base on Your Boat
Decks up to 7/16" thick
Decks up to
7/16" Thick
Where access to the underside of the deck is
not available, the mounting base can be mounted
using wellnuts. Use the base as a template to mark
locations and drill four 1/2" holes. Mount the base
using four 1/4-20 x 4" truss head screws and four
wellnuts. Tighten the screws so the wellnuts are
firmly compressed as pictured.
Base
Wellnuts
Base
Decks thicker than 7/16"
For decks thicker than 7/16", or where the
underside of the deck is accessible, mount the base
with screws, nuts, and washers. Use the base as a
template to mark the locations and drill four 9/32"
holes. Use four 1/4-20 x 4" truss head screws and
four each flat washers, lock washers, and nuts.
Fasten the base to the deck as pictured. NOTE:
Wellnuts cannot be used on decks thicker than
7/16".
Decks Thicker
Than 7/16" Thick
Washers, Lock Washers,
Screws, & Nuts
Decks thinner than 1/4"
Use a Cannon deck plate to prevent deflection
and add stability to decks thinner than 1/4". Use the
deck plate as a template to
Screws
mark the hole locations.
Deck Up to
7/16" Thick
Deck Plate
Deck Thicker Than 7/16"
Washers, Lock
Washers, Screws,
& Nuts
Wellnut
FOR MAG 10 HS and MAG 10 TS:
If access to the underside of the deck is not
available, the deck plate can be mounted using
screws and wellnuts. Drill 1/2" holes. Use four 1/4-
20 x 2" flat head screws and four wellnuts to mount
deck plate as pictured. Tighten the screws so the
wellnuts are firmly compressed.
Where the underside is accessible, the deck
plate can be mounted using screws, nuts, and
washers. Drill 9/32" holes. Use four 1/4-20 x 2" flat
head screws, nuts and washers (flat and lock).
Fasten plate to deck as pictured. To secure the
mounting base to the deckplate use four 1/4-20 x 2"
truss head screws.
The Low-Profile Swivel Base mounting follows the
same procedure as for the deck plate except that
four 1/4”-20 x 2 1/2" truss head screws are used
to fasten the mounting base and four additional
1/4”-20 x 2 1/2" truss head screws fix the swivel
base to the boat deck.
Low-Profile Swivel Base
NOTE: When using the telescopic boom, we
strongly recommend the use of a deck plate on all
boats to provide adequate stability for the
downrigger.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Downrigger on the Base
Slide body over the lip of the base, with boom
outboard or facing the stern. Lift Lock Knob to hold
threaded shaft clear of base until body completely
covers base. Turn Lock Knob clockwise to tighten
the downrigger to the base.
Tip: Periodically check base to ensure integrity.
The base should be replaced at least every 5 years.
Lock Knob
Setting Up Your Downrigger
Attaching the Boom
3/4”-Long
Boom
Telescopic Boom
The intermediate section of the telescopic boom
must be extended approximately 5" before the
boom locking screw can engage the hole in the
boom. Slip the boom end into the frame and align
the holes. Secure with boom locking screw.
To adjust boom length, with the boom extending
away from you, rotate clamps approximately 1/4
turn counter - clockwise to unlock, and slide boom
section to desired position. To lock, rotate clamp
clock-wise until tight.
The Locking Screw Must
Engage Hole in Boom
Clamps
The Standard 24 Inch Boom inserts into the
downrigger frame. Be sure that the boom is held
securely by seating it firmly against the shoulder
inside the fame and fastening the boom locking
screw such that it engages the hole in the boom.
Standard 24-Inch
Boom
Assemble Swivel Head To Boom
Insert the telescopic boom-end into the boom-
align holes and fasten in place with a #8x5/8
screw. Spread the swivel head side plates and
slip the assembly over the boom end axle. Snap
the assembly together and install two #4x1/2"
screws into the swivel head.
TIP: Adjusting the angle of the boom head can help
control cable wrap on the reel.
Swivel Head
Boom
TIP: Whenever downriggers with boom lengths
beyond 24" are used, Cannon's Retro-Ease Weight
Retriever will make bringing in the weight safe and
easy. It attaches to the cable below the boom end
allowing you to pull the weight to yourself without
having to lean way out or collapse the boom to
reach the weight.
#8 x 5/8"
Screw (1)
#4 x 1/2"
Screws (2)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminating the Downrigger Cable
Examine the top of the terminator and note the
order shown in the detail to run cable.
Unwind about 2 feet of cable
and thread the cable through
the rubber cushion.
Cable
Rubber Cushion
CABLE IN
CABLE IN
Attach to terminator.
CABLE OUT
Snap &
Swivel
Tip: A set of pliers with wire cutters is
recommended for this part of setup.
TIP: Use only straight cable, not kinked.
Slide the cushion over the top of the
terminator and give it a test pull.
Lead cable into
HOLE A.
Tighten cable
by squeezing
terminator until
it snaps shut.
Pull six inches of
cable through.
Thread cable
through swivel,
then up into
The cable is set to attach a Cannon
Trolling Weight.
HOLE A
Then pull at top
and bottom
until drawn
tight. Make
bottom of the
terminator.
sure that the
cable threads
the hook.
Lead cable out of
HOLE B and into
HOLE C. Push
the cable until its
end touches the
inside of the
Swivel
terminator hook.
Cannon Uni-Release
Close
The Cannon Uni-Release attaches directly to
the downrigger weight. Attach fishing line to the
clip at the end of the release, and then click
through a series of increasing tension settings.
The release can be used with any test line on salt
or fresh water and may be adjusted from 2 to 22
pounds of grip tension on the line.
Tension
Adjust
Open
Fishing Line
Open
To change line release tension, turn tension knob
to (+) to increase or (-) to decrease. Tension also
may vary according to where the line is placed in
the grips. Higher tension is on the line if it is set
back toward the hinge, and lower if set closer to
the opening. To open the release, spread the
release arms with thumb and forefinger applying
pressure to the sides.
Gripper
Pads
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Rod Holder
The positive lock rod holder incorporates a
locking disk that allows the rod holder to be
aligned in 15 degree increments. Slide the rod
holder tube into the clamp to the desired position
within the recommended area (see below).
Be sure the angled shoulders are facing up.
Place the locking disk into the mating recess of
the frame.
CAUTION: This rod holder is intended for use
of up to 30 lb. test line only, and is not
recommended for use with any tackle IGFA
rated higher than 30 lb. A safety strap (not
included) is recommended for all
applications.
The rod holder assembly is not warranted
when used with tackle above 30 lbs.
Equipment placed in the rod holders and the
loss thereof is the responsibility of the user
and is in no way warranted by JOHNSON
OUTDOORS, INC. Mounting must be in
accordance with the above instructions and
diagram to be warranted.
Slip the clamp arms in place where the
obround tab on the disk fits into the slot on the
clamp. Slide the star washer between the arm of
the clamp and the frame. Place the flat washer
onto the bolt. Then insert the bolt with washer
through the clamp by entering the disk, going
through the frame, the star washer, and out the
other side of the clamp. Tighten the nut to secure
the rod holder. Reposition the rod holder by
loosening the nut and adjusting the tilt.
Single Rod Holder Assembly
Dual Rod Holder Assembly
Star Washer
Placement
Recommended
Area to Clamp
Rod Holder
Angled
Shoulder
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Your Downrigger
Electrical Specifications & Wiring
Instructions
The Mag 10HS \ Mag 10TS \ Mag 5HS are
rated at 25 amps (full load), 12 volts DC and is
protected by a 30 amp manual reset circuit
breaker. Be sure to measure the battery voltage of
your boat.
Your Boat's Electrical Condition
It is important to make sure that your boat is
properly set up before installing your Mag 10HS \
Mag 10TS \ Mag 5HS with Positive Ion Control.
Whenever a boat is in water, various submerged
parts interact to create weak electrical currents.
These weak electrical currents must be
controlled to extend the life of the boat's metal
parts and ensure a good fish catching
environment.
Check the zinc sacrificial anodes on your
boat and on the outboard/outdrive. If they are
more than 50% dissolved they should be
replaced. Any coating of slime or growth should
be cleaned off. All metal parts including the hull
(if metal) must be interconnected by a grounding
wire. This includes motor shafts, outdrives, and
through hull fittings.
WARNING! - DO NOT RUN THIS
DOWNRIGGER ON A 24 VOLT BATTERY
SYSTEM. THIS WILL DAMAGE THE UNIT AND
VOID YOUR WARRANTY.
Connecting to the Battery:
It is strongly recommended that a fuse or
manual-reset circuit breaker be installed at the
battery on the positive lead of the power cable or
that you connect the downrigger to a battery
selector switch. (See Fuse and Wire
Specifications below.)
Connect the positive lead (RED) to the (+)
post on your battery or the downrigger will not
operate. Use the new quick disconnect plug to
remove the downrigger without touching the
battery.
If your boat and zincs are set up correctly,
the voltage on the stainless steel spool wire of
your downrigger should be positive when in
contact with the water. The following tips can be
useful:
•
•
Use Cannon vinyl coated lead weights. Lead,
if not pure, can produce negative charges.
Tip: Control degradation of the power cables and
limit corrosion by using Cannon Ox-Not anti-
oxidant gel on all connections.
Use the trolling weight insulators supplied
with your downrigger. This insulates your
weight from the positive charge on the cable.
This will also ensure that the trolling weight
will stop at water level when retrieved.
FUSE / BREAKER SPECIFICATIONS:
30 Amp, 32 Volt, waterproof, fast blow.
WIRE SPECIFICATIONS:
0-15 ft.
15-25 ft. (5-8 meters)
25-30 ft. (8-9 meters)
(0-5 meters)
10 gauge
8 gauge
6 gauge
•
•
The cable on your downrigger should be
replaced every two years. Etching of the
cable can weaken it physically and
electrically.
CAUTION: When using wire longer than that
provided with your unit, follow the above chart.
When running more than 30 feet from the battery,
contact a qualified electrician.
In saltwater, make sure the sacrificial zincs
are replaced when half dissolved. This
ensures that the boat will run with a neutral
or slightly positive charge. Clean zincs on a
regular basis with a non-corrosive brush.
•
Always make sure the boat is properly
grounded to the water. This will help ensure
proper PIC voltage on the cable and that the
Short Stop will function properly.
Battery
Fuse Holder
Circuit Breaker
Battery
Note: Your Mag 10HS \ Mag 10TS \ Mag 5HS must be unplugged to
check the natural voltage on the stainless steel cable.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your Downrigger
After mounting the Cannon downrigger to your
boat, release some line from your rod and reel so
that the lure is anywhere from 5 to 100 feet behind
the boat. This is called drop back. Attach the
fishing line firmly into the line release. Press and
hold the toggle switch down to lower the weight to
the desired depth as indicated on the depth meter.
Place the fishing rod in the rod holder and reel up
the slack so that your rod has a slight bend in it.
When a fish strikes the lure, the line will separate
from the release. Then you will be free to fight the
fish and bring it in on your rod and reel.
To Lower
Weight
Lowering the Weight
The Mag 10HS \ Mag 10TS \ Mag 5HS can
lower the trolling weight manually or powered.
Manual Descent: Fast or Slow
By turning the clutch knob gently clockwise
(toward the boom), you can let your trolling weight
descend as fast or as slowly as you wish. Turning the
knob counterclockwise (away from the boom) stops
the weight. This gives you control to let it plunge
rapidly or sink slowly to a predetermined trolling
depth. With multiple downriggers, you could start all
your weights creeping down, one at a time, and then
stop them each in turn.
3-Position
Motor
Switch
Powered Descent: One speed fits all.
Hold the toggle switch down until the weight
reaches the desired depth and release. The motor will
stop when switch is released or moved to the neutral
position.
Raising the Weight
Push the toggle switch up momentarily and
release. The weight will rise until it reaches the
surface and then automatically stop.
If you want to raise the weight farther push the
toggle switch up and hold until the weight reaches the
desired position, then release.
To stop the weight during ascent, push the toggle
switch down momentarily (approximately 1 second).
NOTE: If your reel continues to slip no matter how
hard you tighten the brake adjust knob refer to the
Troubleshooting section of this booklet.
Raise
Off
Lower
Caution: The brake adjust knob (clutch) should be
adjusted so that it is tight enough to hold the weight
and the lure at the speed you are trolling. Over-
tightening may cause damage to your downrigger
when weight hangs up on bottom structure or other
obstacles
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Depth Meter
The Cannon Depth Meter provides non-slip
accuracy, plus easy resetting. To reset, just slide the
meter away from the reel until the gears are
disengaged. Spin meter gear to change setting.
NOTE: Actual fishing depth may vary from depth
shown on meter due to trolling speed and weight
of cannon ball. (See "Blowback" on page 12)
The Short Stop System
The Short Stop system is composed of three
critical components: the electronic unit, the reel set
screw, and the trolling weight insulator.
While the downrigger cable is in the water, there
is a minute electrical current that flows between the
cable and the grounded metal boat components in
the water. When the cable clears the water, this
current flow will stop. The Short Stop system senses
this interruption and turns off the motor. The trolling
weight insulator is used to break the cable contact to
the water while the weight is still in the water. The
reel set screw allows the circuit path to be made
through the structure of the downrigger.
1/16"
NOTE: It may be necessary to use two trolling
weight insulators.
Stopping the weight at water level eliminates the
cable strain caused by bouncing weights or weights
hitting the boom end. Stopping at water level will
also keep the weight from hitting the boat hull.
Cable
Terminator
NOTICE: Short stop and Positive Ion
Control features do not function when
spooled with monofilament or super
lines.
Weight
Insulator
Maintaining Your Downrigger
Periodically, lightly grease the thrust bearing
and bearing race found behind the clutch knob.
Replace the cable at least every two years. There
are no other user serviceable parts on the Mag
10HS \ Mag 10TS \ Mag 5HS. Your warranty will
be void if the seal on your unit is broken. For repairs
or servicing your downrigger refer to the Warranty
Information section of this booklet.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The Positive Ion Control System
Your boat has an electrical charge around the
hull in water. If a boat is properly bonded and
properly zinced, that charge should be slightly
positive when measured from ground to the
downrigger cable. Positive Ion Control (PIC) is the
use of electricity to control that charge and its
fluctuation so that it is always maintained at a
specified set voltage.
Using Positive Ion Control
Positive Ion Control is very effective when
trolling. The zone of attraction created at the
downrigger wire will attract the fish. It is best to use
a short drop back between the downrigger release
and the lure. Drop backs of 10 to 20 ft. are typical.
A drop back of 50 to 100 ft will entirely negate the
effects of the PIC circuit.
The practice of setting up and maintaining a
slight positive charge on fishing gear has been
used by commercial fishermen for many years.
This practice has enabled some fisherman to
increase yield when used along with other good
fishing and boating practices.
Cannon’s electric downriggers offer fishermen
a big advantage in being able to stabilize and
control the positive charge around their boat.
Because of the Lexan® construction of the frame,
Cannon downriggers are insulated from your
boat’s hull charge. When the stainless steel
downrigger cable is lowered into the water, the
natural ionization between the cable and the boat
creates a positive charge of 0.7 to 0.9 volts in
saltwater and 0.3 to 0.6 volts in fresh water. This
natural voltage is dependent upon salinity and
mineral content of the water. Your actual voltage
may vary.
The PIC can be one of your best fishing
advantages, depending on fish type and location.
For example, Puget Sound Steelhead may not be
effected the same as Great Lakes Steelhead. To
fully benefit from PIC technology, it is important that
your boat is properly grounded. For more
information on this subject, refer to “Secrets of
Fishing with Electricity” by Ollie Rode.
Blowback
Simply stated, blowback is what happens to the
downrigger weight when you pull it through the
water behind your boat. As your speed increases,
so does the horizontal distance between the weight
and your downrigger. The faster you go, the farther
the weight is behind you. The farther the weight is
behind you, the shallower the weight is.
The following charts provide you with blowback
information for three sizes of Cannon downrigger
weights pulled at three different speeds with no
lures attached and with no current. Current drag,
water salinity and the use of non-Cannon products
will affect your actual trolling depth.
As an example, the first chart shows that if you
are trolling at 4 MPH with an 8 pound weight and
you have 100 FT. of cable in the water with no
current; the downrigger ball is actually at a depth of
about 80 FT.
How the Positive Ion Control System Works
The PIC system uses an internal circuit that
passes the voltage through the drive train of the
Mag 10HS \ Mag 10TS \ Mag 5HS to the reel set
screw. The set screw contacts the cable. Care
must be taken to ensure contact between the
cable and the set screw when replacing the cable.
The positive Ion Control system applies a
constant 0.6 volts on the trolling cable at all times.
Measuring the Natural Electrolysis and PIC
Voltage on Your Boat
A voltmeter with a scale of zero to one volt will
measure the natural electrolysis. Place the ground
lead of the meter on the motor or the battery
ground. Place the positive lead on the stainless
steel downrigger cable while it is in the water. The
downrigger must be unplugged. The voltage you
measure on the volt meter is your boat’s natural
electrolysis voltage. Use the same set up to
measure the PIC voltage; just plug in the Mag
10HS \ Mag 10TS \ Mag 5HS.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Blowback Charts
8-Lb. Weight at 2, 4, and 6 MPH
Trouble Shooting
PROBLEM: Up or down will not work.
SOLUTION:
Check the battery cable polarity then check the
battery voltage.
A properly connected and charged battery is
important for safety and for proper operation of
the downrigger.
2 MPH
4 MPH
6 MPH
PROBLEM:
The Mag 10HS \ Mag 10TS \ Mag 5HS fails to
continue running after toggle switch is pushed
up and held momentarily, while cable is still in
water, or is having problems with the PIC
voltage.
SOLUTION:
Make sure your boat is properly bonded. A boat
that is properly bonded has an electrical path
from the negative battery terminal to all metal
parts on the boat that contact water.
Additionally, in saltwater the boat must be
properly zinced to show a natural electrolysis
voltage of 0.7 to 0.9 volts. The voltage supply to
your downrigger must also be bonded to the
boat.
Amount of Cable in Water (ft.)
10-Lb. Weight at 2, 4, and 6 MPH
2 MPH
4 MPH
PROBLEM:
6 MPH
Clutch slips
SOLUTION:
The set screw in the reel may have come loose
off the shaft. Follow the instructions below:
1) Unwind the cable from the reel.
2) Remove the set screw.
3) Align the set screw hole in the reel with the hole
in the reel shaft by inserting a 3/16" or smaller
rod and rotating the reel until you feel it drop
into the shaft hole.
Amount of Cable in Water (ft.)
4) Replace the set screw and tighten until you feel
resistance.
12-Lb. Weight at 2, 4, and 6 MPH
2 MPH
4 MPH
5) By gently rocking the reel back and forth while
tightening the set screw, you can feel it engage
in the shaft hole. The half dog point on the set
screw must enter the hole in the shaft; not just
be tightened against the reel shaft.
6) The set screw should be about 1/16" above the
top of the hole when it is properly seated (not so
for TS models). The contact between the
stainless steel cable and the set screw is
important for proper operation of the Positive
Ion Control system.
6 MPH
13
Amount of Cable in Water (ft.)
Download from Www.Somanuals.com. All Manuals Search And Download.
5) Locate fish on a vertical plane. Place lures
in areas where fish might be. Skilled fishermen
call these areas the “strike zones”. They include
the edges of the week beds, structure along
bottom, drop-offs, preferred temperature of the
target species, and the thermocline. Remember
that fish occupy certain areas for certain reasons
(sources of food, protective cover, preferred
temperatures, etc.).
Ten Good Trolling Tips
1) Test your lures over the boat side before
sending them down and back. Do this to make
sure the lure wiggles and wobbles properly
without going belly up or wandering off. Some
lures can be adjusted, fine tuned actually, to
impart maximum action. For example, a slight
bend in the tail of a spoon or twist of the hook
eye in the nose of a plug can make a noticeable
difference in how the lure performs.
6) Consider special knots and swivels. A
good ball bearing swivel will all but eliminate line
twist and will aid in getting maximum
Also, when running two or more lures, make
sure the offerings are compatible. Lures that run
out of harmony with each other are bound to
tangle and that means wasted time to straighten
out the mess. Testing them first will avoid the
problem.
performance from a lure. Many anglers add the
tiny swivels to split rings already on the lure
itself. On the other hand, a swivel may dampen
the action of a sensitive lure, such as a Rapala.
Some fisherman tie tiny improved cinch or loop
knots. Loop knots in particular may enhance up
and down and side to side action of lures. Any
good fishing manual will explain how to tie these
and other knots.
2) Consider different sizes, shapes, and
colors of lures. No one has ever figured out with
precision what makes a fish strike or snub a lure.
There is no doubt, that matching the forage
(minnows, crayfish, etc.) in color, shape, action,
and size can help trigger those strikes from
hungry fish. On the other hand, if fish such as
bluegills, small mouth bass or Coho salmon are
protecting spawning beds, they may attack
whatever is threatening. So, bright colors in lures
may out produce bland colors.
7) Consider releases for flatline trolling. A
good tip is to secure a piece of downrigger cable
or heavy monofilament to the water ski hook or
handle below the transom of most boats. To the
other end of the mono or cable, add a pinch-r-
release. After letting out your lure to the desire
distance, put the rod in its holder, then bend the
tip and secure the fishing line in the release.
3) Vary trolling speeds. Goosing the engine
now and then or slowing to a crawl every so
often will change the action of the lures and may
get fish to strike them.
8) Add a weed guard. Having trouble with
weeds hanging up lures? Consider tying a three-
inch piece of monofilament a foot above the lure.
Leaves, smaller weeds and other debris may
catch here momentarily then fall off to the side of
the lure without tangling. Weedless lures are
another smart consideration. Downrigger cables
are effective weed catchers when trolling for
pike, muskies, or bass in weed-infested lakes.
4) Vary trolling patterns and lead lengths.
The amount of line you let out often determines
how deep the lure will run and, to some extent,
what degree of action it will impart. For starters,
consider running lures about ten feet behind
downrigger weights. If flat line trolling, put them
back about fifty feet, then experiment depending
on what the fish do.
9) Add a stinger hook. When fish short strike,
slap at lures without becoming hooked, adding a
stinger hook can solve the problem. Simply tie a
treble hook to one end of a four inch piece of
monofilament and then tie the extra hook to the
last gang of hooks on your lure. The stinger
hook, which trails the lure, provides extra
insurance.
Trolling patterns affect lure action too, that is
why some anglers like to wheel a lazy S course.
On turns, outside lures will speed up
momentarily while inside lures hang for a
moment or two. Fish may nail lures that change
speeds. Also, zigzag patterns allow for more
water coverage, plus it keeps lures out of
propeller boil, an important consideration for
browns and other wary species.
10) Keep hooks sharp. Some of the best
fishermen sharpen all hooks after every fish
caught. Hooks get dull through both use and
misuse, and probably more fish are lost to dull
points than anything else.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CANNON® LIMITED WARRANTY
CANNON® SERVICE POLICY
AFTER THE APPLICABLE WARRANTY PERIOD
Johnson Outdoors Inc. warrants to the original purchaser that if the
accompanying product (see exclusions below) proves to be defective
in material or workmanship within the following warranty periods,
Johnson Outdoors Inc. will, at its option, either repair or replace same
without charge (but no cash refunds will be made):
After the applicable warranty period, or, if one of the above
exclusions applies, Cannon® products will be repaired for a charge of
parts plus labor. All factory repairs, after the applicable warranty
period, carry a 90-Day Limited Warranty, subject to the exclusions and
limitations stated above.
1) The boom, motor, and reels, plus all Lexan®* parts, including
but not limited to frames and bases, will be free from defects in
materials and workmanship, subject to normal wear and tear,
for the original purchaser's lifetime.
TO ENFORCE WARRANTY OR TO
OBTAIN REPAIRS AFTER WARRANTY
2) All other items will have 1-year limited warranties from the
date of original retail purchase, except THE FOLLOWING
ITEMS THAT HAVE NO WARRANTY WHATSOEVER: boot
covers, clothing, Dacron line, rubber bands, swivel lock pin,
weights, and wire cable.
This limited warranty may be enforced only by the original
purchaser; all subsequent purchasers acquire the product "as
is" without any benefit of this limited warranty. Repair or
replacement of the product as set forth in this limited warranty
shall be the original purchaser’s sole and exclusive remedy
and Johnson Outdoors Inc.’s sole and exclusive liability for
breach of this warranty.
To obtain warranty service in the U.S., the downrigger or part
believed to be defective and the proof of original purchase (including
the date of purchase) must be presented to a Cannon® Authorized
Service Center or to Cannon®’s factory service center in Mankato,
MN. Except as noted below, any charges incurred for service calls,
transportation or shipping/freight to/from the Cannon® Authorized
Service Center or Cannon®’s factory, labor to haul out, remove, re-
install or re-rig products for warranty service, or any similar items are
the sole and exclusive responsibility of the purchaser. Downriggers
purchased outside of the U.S. (or parts of such downriggers) must be
returned prepaid with proof of purchase (including the date of
purchase and serial number) to any Authorized Cannon® Service
Center in the country of purchase. Warranty service can be arranged
by contacting a Cannon® Authorized Service Center listed on the
enclosed sheet, or by contacting the factory at 1-800-227-6433 or Fax
1-800-527-4464. If the necessary repairs are covered by the warranty,
we will pay the return shipping charges to any destination within the
United States.
EXCLUSIONS
This warranty does not apply in the following circumstances:
• When the product has been connected, installed, combined,
altered, adjusted, serviced, repaired, or handled in a manner
other than according to the instructions furnished with the
product
• When the motor housing is opened by anyone other than
Cannon® Authorized service repair personnel.
DO NOT return your Cannon® downrigger or parts to your retailer.
Your retailer is not authorized to repair or replace them.
• When any defect, problem, loss, or damage has resulted from
any accident, misuse, negligence, carelessness, or abnormal
use, or from any failure to provide reasonable and necessary
maintenance in accordance with the instructions of the owner's
manual
Major parts, such as the motor and main frame, must be returned
to Johnson Outdoors Inc. in Mankato, Minnesota, or a Cannon®
Authorized Service Center, for repair or replacement. To reduce
shipping costs, we suggest removal of loose parts such as the boom
and rod holders. Small parts that can be easily removed such as the
handle and/or the counter, may be removed from the downrigger and
returned for repair or replacement.
LIMITATION AND EXCLUSION OF IMPLIED WARRANTIES AND
CERTAIN DAMAGES
THERE ARE NO EXPRESS WARRANTIES OTHER THAN
THESE LIMITED WARRANTIES. JOHNSON OUTDOORS INC.
DISCLAIMS LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL
DAMAGES, AND IN NO EVENT SHALL ANY IMPLIED
Retain your sales receipt! Proof of purchase must accompany
product when returned.
Return Address:
Johnson Outdoors Inc.
Cannon Division
WARRANTIES (EXCEPT ON THE BOOM, MOTOR, REELS, AND
ALL LEXAN®* PARTS), INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE,
EXTEND BEYOND ONE YEAR FROM THE DATE OF PURCHASE
(AND IN THE CASE OF THE BOOT COVERS, CLOTHING, DACRON
LINE, RUBBER BANDS, SWIVEL LOCK PIN, WEIGHTS, AND WIRE
CABLE, JOHNSON OUTDOORS INC. DISCLAIMS ALL IMPLIED
WARRANTIES). THIS WRITING CONSTITUTES THE ENTIRE
AGREEMENT OF THE PARTIES WITH RESPECT TO THE
SUBJECT MATTER HEREOF; NO WAIVER OR AMENDMENT
SHALL BE VALID UNLESS IN WRITING SIGNED BY JOHNSON
OUTDOORS INC.
121 Power Drive
Mankato, MN 56001
FOR YOUR INFORMATION:
Serial No.
Date Purchased
Store Where Purchased
Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of consequential damages, so the
above limitation or exclusion may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights that
vary from state to state.
RETAIN THIS SECTION FOR YOUR RECORDS
* Lexan is a registered trademark of General Electric.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ENVIRONMENTAL COMPLIANCE STATEMENT:
It is the intention of Johnson Outdoors Inc. to be a responsible corporate citizen, operating in compliance with known and applicable
environmental regulations, and a good neighbor in the communities where we make or sell our products.
WEEE Directive:
EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers, and manu-
facturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electronics to take responsibility
for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle.
WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE de-
signed and intended as fixed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In some European Union
member states, these vehicles are considered outside of the scope of the Directive, and EEE for those applications can be considered excluded
from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of with other household refuse.
It must be disposed of and collected for recycling and recovery of waste EEE.
Johnson Outdoors Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply in the collec-
tion, treatment, recovery, and environmentally sound disposal of those products; however, these requirement do vary within Euro-
pean Union member states. For more information about where you should dispose of your waste equipment for recycling and
recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your prod-
uct was purchased.
To download product manuals or purchase Cannon products from an authorized dealer, please visit our web page at
Johnson Outdoors, Inc. / Cannon Division
121 Power Drive, Mankato, MN 56001
1-800-227-6433
© 2008 Johnson Outdoors, Inc. All rights reserved.
All CANNON Downriggers are covered by US Pat.D-269, 992. Copyright 2006 Johnson Outdoors, Inc. All rights reserved.
Conforms to 89/336/EEC (EMC) under standards EN 55022A, EN 50082-2 since 1996 LN V9677264
WARNING: This product contains chemical(s) known to the state of California to cause cancer and/or reproductive toxicity.
16
Form No. 3397102 Rev D
Download from Www.Somanuals.com. All Manuals Search And Download.
|