BOSCH
MAKERS WARRANTY
Cooktop
Model No: PCL 785 FAU
USER INSTRUCTIONS
INSTALLATION INSTRUCTIONS
MAINTENANCE INSTRUCTIONS
This cooktop is for use with Natural and Propane gases
Leave these instructions with the owner
BOSCH
Part No: W1531
Version (Bosch) A
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Contents
It is not always necessary to call the Service Centre. In
some cases, you may be able to solve the problem
yourself. This table contains some useful information.
Contents ....................................................... 3
Safety considerations ...................................... 4
For your safety .......................................... 4
What to do if you smell gas......................... 4
Warnings ................................................. 4
Installation..................................................... 6
Preparing to install ..................................... 6
Clearances ............................................... 7
Installation of cooktop into kitchen bench ....... 7
Installation procedure............................. 7
Connection ............................................... 8
Electrical connection .............................. 8
Gas connection..................................... 8
Conversion from Nat. Gas to Propane Gas .... 9
To change injectors ................................ 9
Injector size chart .................................. 9
Minimum flame adjustment ................... 10
Operating instructions ................................... 11
Burner location ........................................ 11
Burner ignition & control ........................... 11
User instructions ........................................... 12
Boiling burners ........................................ 12
Wok trivet .......................................... 12
Wire coffee support............................. 12
Cleaning and care ................................... 13
Do’s .................................................. 13
Don’t ................................................. 13
Service ....................................................... 14
Trouble shooting ...................................... 14
Wiring diagram ...................................... 15
Service contact telephone numbers ............. 15
Trouble shooting
chart
Important:
Only authorised personnel from the Service Centre
are qualified to work on the main gas and electric
systems.
What’s wrong
Possible cause
Solution
...If none of the electrical • Power turned off.
systems work.
• Turn power on.
• Faulty fuse.
• Check the fuse in the main
fuse box and replace if faulty.
• Check to see if the circuit
breaker or a differential has
been triggered in the mains
supply box.
• The automatic circuit
breaker or mains.
differential has been
triggered.
...If the electronic ignition • There may be food or • The gap between the spark
system does not work.
cleaning product
particles between the
spark plugs and the
burners.
plug and the burner needs to
be cleaned carefullly.
...If the flame on the
burners is not evenly
distributed.
• The burner components • Put the components in their
have not been
correct positions.
assembled properly.
• The gas ports on the
burners are dirty.
• Clean the gas ports on the
burners.
...If the gas flow does not • The isolation valve is
• Open the isolation valve.
seem normal or there
is no gas flow at all.
closed.
• If the gas is supplied
from a gas bottle, it
may be empty.
• Replace the gas bottle with a
full one.
...If the kitchen smells
of gas.
• One of the valves has • Check to see if a valve has
been left open.
been left open.
• Possible leak on the
gas bottle coupling.
• Check that the coupling on
the gas bottle is in order.
...If the safety cut-off
devices on the different
burners do not work.
• The control knob has
not been kept
• Once ignited, keep the
control pressed in for a few
seconds.
pressed in for long
enough.
• The burner ports are
dirty.
• Clean the burner ports.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Safety considerations
• If the information in this manual is not followed ex-
Do’s
For your safety
Cleaning
actly, a fire or explosion may result causing prop-
erty damage, personal injury or death.
• Once the appliance is cold, clean it with a sponge
and soapy water. Remove any spills immediately.
This will avoid unnecessary effort later.
• Allow burners and trivets to cool down before clean-
ing them.
• Do not store articles on or against this appliance.
• Do not store flammable materials near this appli-
ance.
• Do not spray aerosols in the vicinity of this appli-
ance while it is in operation.
• The burners and trivets must be cleaned regularly to
keep them in good condition. This is done by sub-
merging them in soapy water and scrubbing them
with a non-metal brush to keep the ports and slots
free from obstructions so they give a perfect flame.
Dry the burner caps and trivets whenever wet or
damp.
• After cleaning and drying ensure that the burner
heads and caps are replaced correctly on the burner
body. Refer Fig. 6.
• The high temperatures generated by using the wok
burner may cause the stainless steel hob of your
hotplate to become discoloured over time. THIS IS
NORMAL. Clean the hob with a product suitable
for cleaning stainless steel.
• The trivets on your hob are fitted with rubber feet.
Be careful when cleaning as they may be dislodged
during cleaning, leaving the stainless steel hob un-
protected and subject to surface scratching .
• Do not try to light the appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbour’s
phone. Follow the gas supplier’s instructions.
What to do if you
smell gas
• If you cannot reach your gas supplier, call the fire
department.
• Installation and service must be performed by an
authorised person.
1. Do not allow the flame to extend beyond the edge
of the cooking utensil. This instruction is based on
safety considerations.
2. Do not forget that the unit becomes hot when in
use. Common sense is important. Just because
the flame is out, does not mean parts cannot still
be hot.
3. This appliance shall not be used for space heat-
ing. This instruction is based on safety considera-
tions.
Warnings
Don’t
• Never use abrasive products, sharp objects, steel
scouring pads, knives, etc., to remove stubborn food
remains from the hob surface, trivets and burners.
• Do not allow acidic products such as vinegar, lemon
juice, etc., to come into contact with the hob.
4. Be sure to disconnect the electrical supply before
disassembly of the appliance.
5. Keep the appliance area clear and free from com-
bustible materials, gasoline and other flammable
vapours and liquids.
6. This appliance must be installed in a position
with the proper level of ventilation. Do not ob-
struct the flow of combustion and ventilation air.
7. Cabinets installed above the gas cooktop must
have a minimum clearance of 650 mm (24”).
8. The gas pressure regulator supplied with the ap-
pliance must be installed in line with the gas pipe.
(N.G. only)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
13
User instructions
Use ‘High flame’ setting to bring the pan to the boil,
9. For pressure testing in excess of 3.5 kPa
(1/2 psig) the appliance and its individual shut-
off valve must be disconnected from the gas sup-
ply piping system.
Boiling burners
then adjust the flame between ‘High flame’ and ‘Low
flame’ to maintain the required pan temperature.
Important:
10. Important
The use of a cooktop leads to the production of heat
and moisture in the kitchen. For this reason make sure
that the room is properly ventilated. Keep natural ven-
tilation openings, such as windows, open or provide
a mechanical ventilation device (e.g. a range hood or
overhead exhaust fan).
For safety and economic gas usage you should al-
ways use the correct pan on the correct burner. Flames
should not protrude beyond the base of the pan. You
will save energy, time and money by always placing
the correct pan size on the correct gas ring.
See fig. 15.
When using a very large pot, leave a gap of at
least 50 mm (2”) to avoid damaging any parts in
bench top wood, plastic or other non-heat resistant
materials. Never leave oil or hot fat unattended.
Note: To avoid jeopardising the electrical safety of the
appliance, it is forbidden to use high-pressure or steam
jet cleaning devices.
15
The chart below gives the correct pan usage for each
burner.
Burner
Recommended Minimum
pan diameter
pan diameter
Small burner
100 - 240 mm 100 mm
Medium, large & 180 - 260 mm 180 mm
wok burner
Wok trivet
The hotplate is supplied with an extra wok trivet. This
trivet must be used when using the wok burner for
receptacles with diameters of more than 26cm diam-
eter, griddle plates and all kinds of concave recepta-
cles such as woks, etc.
Wire coffee support
This support is for use only with the small burner when
supporting receptacles with a diameter of less than
10cm.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Operating instructions
Burner locations
Installation
This installation must conform with the following:
Preparing to install
• Manufacturer’s Installation instructions
• Local Gas Fitting Regulations
• Municipal Building Codes,
• AGA Installation Code for Gas Burning Appli-
ances. (AS 5601AG 601)
• S.A.A. Wiring Code
• Local Electrical Regulations
• Any other statutory regulations
These built-in hobs are intended to be inserted in a
benchtop cutout.
Only an authorised person should connect the appli-
ance.
Installation dimensions are shown in Fig.1
13
1. Small burner
2. Medium burner
3. Wok burner
4. Large burner
5. Medium burner
6. Control knobs
Depress control knob and turn anti-clockwise to ‘High
flame’ position. Hold the knob down for a few sec-
onds until the flame ignites. Keep control knob de-
pressed for a few seconds to activate the flame failure
device. If ignition fails, depress knob again and wait
for ignition. Turn anti-clockwise to set the flame to the
desired intensity.
Burner ignition &
control
All burners are fitted with a flame failure device which
shuts off the gas supply if the flame extinguishes for
any reason. To re-ignite, wait 30 seconds for any
unburnt gas to disperse before repeating the ignition
procedure described above.
To turn off the gas supply to a burner turn the control
knob clockwise to the ‘OFF’ position. (Refer Fig. 14)
1
14
Before connecting the unit, check whether the local
connection conditions (type of gas) are compatible
with the unit’s settings. Observe any special condi-
tions imposed by local suppliers (utilities). The specifi-
cations of this cooktop are stated on the data label
located on the bottom of the cooktop base.
The control knob is used to adjust the flame of the gas
burner.
‘Low flame’ graphic = lowest output
‘High flame’ graphic = highest output
6
Download from Www.Somanuals.com. All Manuals Search And Download.
11
A range hood fitted above the top must be installed
according to the installation instructions for the range
hood. A minimum distance of 650 mm is required for
a range hood and 750 mm for an exhaust fan.
If the distance measured from the periphery of the
nearest burner to any vertical surface is less than 200
mm, the surface shall be protected in accordance with
clauses 5.12.1 & 5.12.1.2 of AS 6501/AG 601.
Leave a space at least 100mm between any drawer,
partition or oven that is installed underneath the
cooktop.
Minimum thickness of benchtop is 15mm. See Fig. 2.
Installation procedure:
1. For cutout dimensions and clearances refer Fig 1.
2 The hotplate is factory fitted with sealing tape
around the lower edge of the hob and two pres-
sure clamps either side. The seal keeps the entire
work surface watertight and prevents spillage from
leaking into cupboards underneath. Please ensure
that the sealing tape is not disturbed during the
installation process. Refer Fig. 3.
3 Place hotplate on top of the bench cut-out and press
down firmly on all edges at the same time t1ate0074ed
7
Installation continued
It should be expressly noted that we cannot accept
any liability for direct or indirect damage caused by
wrong connection or improper installation. When
being repaired, the appliance must always be
disconnected from the mains supply; if required,
notify our customer service.
Electrical:
Connection
An electrical 10 amp socket needs to be within 1 m of
the hotplate to allow electrical connection. The socket
must remain accessible after installation of the appli-
ance.
Important note:
This appliance is connected to the mains (240 VAC)
by means of the connecting lead which must be fixed
to the kitchen unit to prevent it from coming into con-
tact with hot parts of the hob (or an oven installed
underneath).. When making this connection make sure
that the lead cannot come into contact with hot parts
of the hob.
To change injectors
Request change-over injectors from our customer serv-
ice department (refer injector chart below for sizes).
Converting the cooktop
from Nat. Gas to
Propane Gas
Natural Gas
Propane Gas
Injector Hourly Gas
size (mm) Consumption
Burner
Injector Hourly Gas
size(mm) Consumption
Important: This appliance must be earthed.
(mm)
0.90
1.20
1.70
1.20
1.60
(MJ)
(mm)
(MJ)
3.25
6.25
13.25
6.25
10.0
Gas:
Left Front
Left Rear
Centre
4.0
0.5
During the planning stage, consider the position of
supply connections.
6.5
0.67
0.97
0.67
0.85
The hob must be connected to the gas supply with
upstream connection of an isolation valve in accord-
ance with the respectively valid regulations. We rec-
ommend that the isolation valve be fitted prior to the
cooktop to enable isolation of cooktop from gas sup-
ply. The valve must be easily accessible at all times.
To find out the factory set gas type, see bottom of
cooktop next to gas connection.
Remove plastic cap from gas supply line prior to in-
stallation.
14.0
6.5
Right Front
Right Rear
12.0
Before conversion the cooktop must be disconnected
from the electricity and gas valves must be turned to
the OFF position.
1 Remove the trivets, burner caps and burner heads.
Refer Fig. 6
2 Change the injectors using a 7-mm socket wrench
and be sure to tighten them down properly so that
they are fully airtight. Refer Fig. 7.
Fit regulator (N.G.) or Propane fitting (Propane) di-
rectly to the R1/ ” connection as per Fig. 4 and Fig. 5.
Direction of ga2s flow is indicated on the rear of the
regulator.
3 Re-assemble the burner component parts in reverse
order.
For position of the inlet connection refer Fig.1.
Natural gas connection
Propane gas connection
NOTE: it is not necessary to adjust the primary air
control on these burners.
4
5
6
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
|