FEED MIXER
524-15B
ASSEMBLY, OPERATION
AND PARTS MANUAL
ROTO-MIX
P.O. BOX 1724
3305 E. Wyatt Earp Blvd.
Dodge City, Kansas 67801
(620) 225-1142
SERIAL NUMBER ____________
441908 05/2007
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
ROTO-MIX LLC, warrants to the original purchaser all products manufactured by it to
be free from defects in material and workmanship under normal use and service.
ROTO-MIX’s obligation under this warranty is limited to repairing or replacing, as the
company may elect, free of charge and without charge for installation, at the place of
business of a dealer or distributor authorized to handle the equipment covered by this
warranty or at a ROTO-MIX plant, any parts that prove, in the company’s judgment, to
be defective in material and workmanship within one (1) year after delivery to the origi-
nal purchaser, and still owned by the original purchaser.
It is a condition of this warranty that the original purchaser must fill out the warranty
card furnished by ROTO-MIX and that it be returned to ROTO-MIX and be recorded in
ROTO-MIX’s owner file for this warranty to be valid. In the event an owner’s card is not
on file at the ROTO-MIX office, the warranty period will extend only from date equip-
ment was picked up or delivered from the ROTO-MIX plant.
It is a condition of this warranty that if within the aforesaid period of time, said equip-
ment, product or parts are determined by the original purchaser to be defective as
herein provided, then such defective part or parts must be delivered by or through a
dealer and/or distributor to ROTO-MIX at its factory with transportation prepaid or war-
ranty shall be of no force or effect and shall be waived by the purchaser. If ROTO-MIX,
or its duly authorized representative, shall find that such returned part or parts are de-
fective and such defects, or defect, are included in and covered by said warranty, then
such defective part or parts shall promptly be replaced without charge to the pur-
chaser, F.O.B. the ROTO-MIX plant.
This warranty shall not apply to any item, manufactured in whole or in part by ROTO-
MIX, which shall have been operated in a manner not recommended by ROTO-MIX
nor which shall have been repaired, altered, neglected, tampered with, or used in any-
way which in the company’s opinion adversely affects its performance. This warranty
shall in no way make ROTO-MIX liable to anyone for personal injuries or damages,
loss of time, or expense of any kind either direct or indirect resulting from part failure or
defect.
This warranty is subject to acts of God, fire and existing conditions of supply and de-
mand, or production, or ability or inability to deliver, or for any other valid reason be-
yond the reasonable control of ROTO-MIX, to obtain materials, manufactured replace-
ment parts, or make delivery thereof.
No distributor, dealer, agent, or employee of ROTO-MIX is authorized to extend any
other or further express or implied warranty or incur any additional obligation on
ROTO-MIX’s behalf in connection with the sale of this product.
ROTO-MIX reserves the right to make changes in design, or additions to, or improve-
ments in its equipment without obligation to install such changes, additions, or im-
provements in equipment previously manufactured.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SCALES WARRANTY & SERVICE POLICY
DIGI-STAR SCALE SYSTEMS
Digi-Star, LLC warrants for a period of one year from date of installation, to
correct by repair or replacement, at Digi-Star’s option, any defect in material or
workmanship in any part of this product. In the event of replacement, Digi-Star’s sole
obligation shall be to provide replacement products or parts. F.O.B. Fort Atkinson,
Wisconsin.
EATON ELECTRONIC SCALES
Eaton scale systems are warranted for two years from the date of manufacture
or a minimum of one year from the date of sale, with proof of purchase, to a maximum
of 36 months from the date of manufacture. Defective products must be returned to
Eaton or an authorized service center, freight prepaid, within warranty period, where
components will be repaired or replaced at Eaton’s discretion.
TYREL INDICATORS
Tyrel Corporation warrants the indicator to be free from defects in material and
workmanship for 12 months from date of delivery. Tyrel Corp. will repair or replace, at
their option, at no charge, any indicator found to be defective. F.O.B. Winooski,
Vermont.
Defective products must be returned to ROTO-MIX, freight prepaid, within the
warranty period. Any deviation from this policy must be approved by the management
of ROTO-MIX.
This warranty does not apply to scale systems that have been subject to
negligent maintenance, accident, modification, abuse, or natural hazards.
All warranty repair work must be done by an authorized ROTO-MIX technician.
Any work done by anyone other than an authorized ROTO-MIX technician shall void
the warranty.
In the event it is necessary for field service to be done, ROTO-MIX is not
responsible for expenses incurred in field service or travel expenses and labor getting
to and from the service point.
All parts returned for warranty work must be identified by customer name, date
sold, date failed, model number, and serial number of instrument.
ROTO-MIX is not responsible and will not be liable for personal injuries or damages,
loss of time or damage caused to persons or property by reason of the installation of
ROTO-MIX products or their mechanical failure.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR QUALIFICATIONS
Operation Of this mixer/feeder shall be limited to competent and experienced
persons. In addition, anyone who will operate or work around a mixer/feeder must use
good common sense. In order to be qualified, he or she must also know and meet all
other qualifications, such as:
1. Some regulations specify that no one under the age of sixteen (16) may
operate power machinery. It is your responsibility to know what these
regulations are in your area and/or situation.
2. Current OSHA regulations state in part: At the time of initial assignment and
at least annually thereafter, the employer shall instruct EVERY employee in
the safe operation and servicing of all equipment with which the employee is,
or will be involved.
3. Unqualified persons are to STAY OUT OF THE WORK AREA.
4. A person who has not read and understood all operating and safety
instructions is not qualified to operate the machinery.
FAILURE TO READ THIS MIXER/FEEDER MANUAL AND ITS SAFETY
INSTRUCTIONS IS A MISUSE OF THE EQUIPMENT.
SAFETY
READ BEFORE
YOU FEED
SAFETY
READ BEFORE
YOU FEED
SAFETY
READ BEFORE
YOU FEED
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS
MANUAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING
YOUR PERSONAL SAFETY AND THE SAFETY OF OTHERS. FAILURE TO
FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.
THIS SYMBOL MEANS
-ATTENTION!
-BECOME ALERT!
-YOUR SAFETY IS INVOLVED!
SIGNAL WORDS: Note the use of the signal words DANGER, WARNING, and
CAUTION with the safety messages. The appropriate signal word for each has been
selected using the following guidelines:
DANGER: Indicates an imminently hazardous situation that, if not avoided, will
result in serious injury or death. This signal word is to be limited to the most
extreme situations typically for machine components which, for functional
purposes, cannot be guarded.
WARNING: Indicates a potentially hazardous situation that, if not avoided, will
result in serious injury or death, and includes hazards that are exposed when
guards are removed. It may also be used to alert against unsafe practices.
CAUTION: Indicates a potentially hazardous situation that, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practices.
If you have questions not answered in this manual or require additional copies or the
manual is damaged, please contact your dealer or ROTO-MIX, 2205 E. Wyatt Earp,
Dodge City, Kansas, 67801. (Telephone) 620-225-1142 (Fax) 620-225-6370
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY FIRST
REMEMBER: The careful operator is the best operator. Most accidents are caused by
human error. Certain precautions must be observed to prevent the possibility of injury
or death.
DO NOT ALLOW PERSONNEL OTHER THAN THE QUALIFIED
OPERATOR NEAR THE MACHINE.
NEVER START MACHINE UNTIL ALL GUARDS AND SAFETY SHIELDS
ARE IN PLACE.
DO NOT CLEAN, ADJUST OR LUBRICATE THE MACHINE WHILE IT IS
IN MOTION.
BEFORE STARTING TRACTOR ENGINE, BE SURE PTO SHIELDS TURN
FREELY.
LOOSE OR FLOPPY CLOTHING SHOULD NOT BE WORN BY THE
OPERATOR.
OPERATING PRECAUTIONS & INSTRUCTIONS:
A. Check to see that no obstructions are present in the mixer prior to start up.
B. Before loading, run the mixer empty and check all operations.
C. Do not overload the mixer, as the mixing efficiency may be reduced and unit damage
may occur. (See loading instructions).
D. Remove all moisture drain plugs if the mixer is going to set in the rain or snow.
E. Be sure all shields are in place before operation.
F. Use common sense when operating.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
EQUIPMENT SAFETY GUIDELINES
Safety of the operator is one of the main concerns in designing and developing
a new piece of equipment. Designers and manufactures build in as many
safety features as possible. However, every year many accidents occur which
could have been avoided by a few seconds of thought and a more careful
approach to handling equipment. You, the operator, can avoid many accidents
by observing the following precautions in this section. To avoid personal injury,
study the following precautions and insist those working with you, or for you,
follow them.
In order to provide a better view, certain photographs or illustrations in this
manual may show an assembly with a safety shield removed. However,
equipment should never be operated in this condition. Keep all shields in
place. If shield removal becomes necessary for repairs, replace the shield prior
to use.
Replace any CAUTION, WARNING, DANGER or instruction safety decal that is
not readable or is missing. Location of such decals are indicated in this
manual.
Do not attempt to operate this equipment under the influence of drugs or
alcohol.
Review the safety instructions with all users annually.
This equipment is dangerous to children and persons unfamiliar with its
operation. The operator should be a responsible adult familiar with farm
machinery and trained in this equipment’s operations. Do not allow persons to
operate or assemble this unit until they have read this manual and have
developed a thorough understanding of the safety precautions and of how it
works.
To prevent injury or death, use a tractor equipped with a Roll Over Protective
System (ROPS). Do not paint over, remove or deface any safety signs or
warning decals on your equipment. Observe all safety signs and practice the
instructions on them.
Never exceed the limits of a piece of machinery. in its ability to do a job, or to
do so safely, is in question - DON’T TRY IT.
LIGHTING AND MARKING
It is the responsibility of the customer to know the lighting and marking
requirements of the local highway authorities and to install and maintain the
equipment to provide compliance with the regulations. Add extra lights when
transporting at night or during periods of limited visibility.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
KEEP ALL SHIELDS IN PLACE
Do not operate mixer/feeder without safety shields in
place.
Rotating parts can crush or dismember causing personal
injury or death.
Disconnect PTO driveline before removing shields for
adjustment or service.
OPERATE MIXER/FEEDER SAFELY
Rotating parts can entangle or strike people, resulting in
personal injury or death.
Never enter a mixer/feeder while in operation.
Operate the mixer/feeder from the operator’s seat only.
Do not exceed load capacity of the mixer/feeder. (See
loading instructions).
Reduce speed when turning or traveling on rough terrain.
Avoid traveling over loose fill, rocks, ditches or holes.
Keep transmissions in gear when traveling downhill.
KEEP RIDERS OFF MIXER/FEEDER
Keep riders off.
Riders are subject to injury such as being struck by
foreign objects and being thrown off. Riders also
obstruct the operator’s view resulting in the
machine being operated in an unsafe manner.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
STAY CLEAR OF ROTATING DRIVELINES
Entanglement in rotating driveline can cause serious
injury or death.
Keep tractor master shield and driveline shields in place
at all times. Make sure rotating shields turn freely.
Wear close fitting clothing. Stop the engine and be sure
PTO driveline is stopped before making adjustments,
connections, or cleaning out PTO driven equipment .
PREVENT BATTERY EXPLOSIONS
Keep sparks, lighted matches, and open flame away
from the top of battery. Battery gas can explode.
Never check battery charge by placing a metal object
across the posts. Use a volt-meter or hydrometer.
Do not charge a frozen battery; it may explode. Warm
battery to 16C (60F)
AVOID HIGH-PRESSURE FLUIDS
Escaping fluid under pressure can penetrate the skin
causing serious injury or death.
Avoid the hazard relieving pressure before
disconnecting hydraulic or other lines. Tighten all
connections before applying pressure.
Search for leaks with a piece of cardboard. Protect
hands and body from high pressure fluids.
If an accident occurs, see a doctor immediately. Any
fluid injected into the skin must be surgically removed
within a few hours or gangrene may result. Doctors
unfamiliar with this type of injury should reference a
knowledgeable medical source.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
PREPARING TRACTOR FOR TRAILER MIXER
POSITIONING DRAWBAR
IMPORTANT: Drive components can be damaged
from excessive speed. Under no
circumstances should a feed mixer
equipped with 540 RPM be operated
by a tractor with 1000 RPM PTO.
Feed mixers are available with either 540 or 1000
RPM driveline. Match tractor PTO with the feed
mixer driveline.
IMPORTANT: To prevent driveline damage, adjust
tractor drawbar to recommended
setting. Disengage tractor PTO before
turning.
Remove clevis if equipped. Turn offset drawbar
down.
Adjust drawbar length:
PTO SPEED
DIMENSION (A)
540 RPM
1000 RPM
14 inches (356 mm)
16 inches (406 mm)
ADJUST TRAILER HITCH CLEVIS
Mixer should be approximately level when attached
to tractor.
Adjust clevis by changing hole location on tongue.
Hitch Pin Size --- 1” x 7”
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SIGNS
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SIGNS
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SIGNS
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
SAFETY DECAL CARE
Keep safety decals and signs clean and legible at all times.
Replace safety decals and signs that are missing or have become illegible.
Replaced parts that displayed a safety sign should also display the current
sign.
Safety decals or signs are available from your dealer or the ROTO-MIX
manufacturing plant.
How to Install Safety Decals:
Be sure that the installation area is clean and dry.
Decide on the exact position before you remove the backing paper.
Remove the smallest portion of the split backing paper.
Align the decal over the specified area and carefully press the small portion
with the exposed sticky backing in place.
Slowly peel back the remaining paper and carefully smooth the remaining
portion of the decal in place.
Small air pockets can be pierced with a pin and smoothed out using the piece
of decal backing paper.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
REMEMBER
Your best assurance against accidents is a careful and responsible
operator. If there is any portion of this manual or function you do not
understand, contact your dealer or the ROTO-MIX plant.
BEFORE OPERATION:
Carefully study and understand this manual.
Do not wear loose-fitting clothing which may catch in moving parts.
Always wear protective clothing and substantial shoes.
Keep wheel lug nuts or bolts tightened to specified torque.
Assure that agricultural implement tires are inflated evenly.
Give the unit a visual inspection for any loose bolts, worn parts or cracked
welds, and make necessary repairs.
instructions included in this manual.
Follow the maintenance safety
Be sure that there are no tools lying on or in the mixer/feeder.
Do not use the unit until you are sure that the area is clear, especially children
and animals.
Because it is possible that this mixer/feeder may be used in dry areas or the
presence of combustibles, special precautions should be taken to prevent fires
and fire fighting equipment should be readily available.
Don’t hurry the learning process or take the unit for granted. Ease into it and
become familiar with your new mixer/feeder.
Practice operation of your mixer/feeder and its attachments. Completely
familiarize yourself and other operators with its operation before using.
Securely attach to towing unit. Use a high strength, appropriately sized hitch
pin with a mechanical retainer.
Do not allow anyone to stand between the tongue or hitch and the towing
vehicle when backing up to the mixer/feeder.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
DURING OPERATION:
Beware of bystanders, particularly children! Always look around to make
sure that it is safe to start the engine of the towing vehicle or move the unit.
This is particularly important with higher noise levels and quiet cabs, as you
may not hear people shouting.
NO PASSENGERS ALLOWED - Do not carry passengers anywhere on, or in,
the tractor or equipment, except as required for operation.
Keep hands and clothing clear of moving parts.
Do not clean, lubricate or adjust your mixer/feeder while it is moving.
Be especially observant of the operating area and terrain - watch for holes,
rocks or other hidden hazards. Always inspect the area prior to operation.
Do not operate near the edge of drop-offs or banks.
Do not operate on steep slopes as overturn may result.
Operate up and down (not across) intermediate slopes. Avoid sudden starts
and stops.
Pick the levelest possible route when transporting across fields. Avoid the
edges of ditches or gullies and steep hillsides.
Be extra careful when working on inclines.
Periodically clear the equipment of brush, twigs or other materials to prevent
buildup of dry combustible materials.
Maneuver the tractor or towing vehicle at safe speeds.
Avoid overhead wires or other obstacles. Contact with overhead lines could
cause serious injury or death.
Avoid loose fill, rocks and holes; they can be dangerous for equipment
operation or movement. Allow for unit length when making turns.
Do not walk or work under raised components or attachments unless securely
positioned and blocked.
Keep all bystanders, pets and livestock clear of the work area.
Operate the towing vehicle from the operator’s seat only.
Never stand alongside of the unit with engine running. Never attempt to start
engine and/or operate machine while standing alongside of unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
DURING OPERATION (CONT.)
Never leave running mixer/feeder unattended.
As a precaution, always recheck the hardware on mixer/feeder following every
100 hours of operation. Correct all problems. Follow the maintenance safety
procedures.
FOLLOWING OPERATION:
Following operation, or when unhitching, stop the tractor or towing vehicle, set
the brakes, disengage the PTO and all power drives, shut off the engine and
remove the ignition keys.
Store the unit in an area away from human activity.
Do not park equipment where it will be exposed to livestock for long periods of
time. Damage and livestock injury could result.
Do not permit children to play on or around the stored unit.
Make sure parked machine is on a hard, level surface and engage all safety
devices.
Wheel chocks may be needed to prevent unit from rolling.
HIGHWAY AND TRANSPORT OPERATIONS:
Adopt safe driving practices:
Keep the brake pedals latched together at all times.
Never use
independent braking with machine in tow as loss of control and/or
upset of unit can result.
Always drive at a safe speed relative to local conditions and ensure that
your speed is low enough for an emergency stop to be safe and secure.
Deep speed to a minimum.
Reduce speed prior to turns to avoid the risk of overturning.
Avoid sudden uphill turns on steep slopes.
Always keep the tractor or towing vehicle in gear to provide engine braking
when going downhill. Do not coast.
Do not drink and drive.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
HIGHWAY AND TRANSPORT OPERATIONS (CONT.):
Comply with state and local laws governing highway safety and movement of
farm machinery on public roads.
Use approved accessory lighting flags and necessary warning devices to
protect operators of other vehicles on the highway during daylight and
nighttime transport.
The use of flashing amber lights is acceptable in most localities. However,
some localities prohibit their use. Local laws should be checked for all
highway lighting and marking requirements.
When driving the tractor and mixer/feeder on the road or highway under 20
MPH (40 KPH) at night or during the day, use flashing amber warning lights
and a slow moving vehicle (SMV) identification emblem.
Plan your route to avoid heavy traffic.
Be a safe courteous driver. Always yield to oncoming traffic in all situations,
including narrow bridges, intersections, etc.
Be observant of bridge loading ratings. Do not cross bridges rated lower than
he gross weight at which you are operating.
Watch for obstructions overhead and to the side while transporting.
Always operate mixer/feeder in a position to provide maximum visibility at all
times. Make allowances for increased length and weight of the mixer/feeder
when making turns, stopping the unit, etc.
PERFORMING MAINTENANCE:
Good maintenance is your responsibility. Poor maintenance is an invitation to
trouble.
Make sure there is plenty of ventilation. Never operate the engine of the
towing vehicle in a closed building.
asphyxiation.
The exhaust fumes may cause
Before working on the mixer/feeder, stop the towing vehicle, set the brakes,
disengage the PTO and all power drives, shut off the engine and remove the
ignition keys.
Be certain all moving parts on attachments have come to a complete stop
before attempting to perform maintenance.
Always use a safety support and block the wheels. Never use a jack to
support the machine.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
READ BEFORE
YOU FEED
PERFORMING MAINTENANCE (CONT.):
Always use the proper tools or equipment for the job at hand.
Use extreme caution when making adjustments.
Never use our hands to locate hydraulic leaks on attachments. Use a small
piece of cardboard or wood. Hydraulic fluid escaping under pressure can
penetrate the skin.
When disconnecting hydraulic lines, shut off hydraulic supply and relieve all
hydraulic pressure.
Openings in the skin and minor cuts are susceptible to infection from hydraulic
fluid. If injured by escaping hydraulic fluid, see a doctor at once. Gangrene
can result. Without immediate treatment, serious infection and reactions can
occur.
Replace all shields and guards after servicing and before moving.
After servicing, be sure all tools, parts and service equipment are removed.
Do not allow grease or oil to build up on any step or platform.
Never replace hex bolts with less than grade five (5) bolts unless otherwise
specified.
Where replacement parts are necessary for periodic maintenance and
servicing, genuine factory replacement parts must be used to restore your
equipment to original specifications. ROTO-MIX will not claim responsibility for
use of unapproved parts and/or accessories and other damages as a result of
their use.
If equipment has been altered in any way from original design, ROTO-MIX does
not accept any liability for injury or warranty.
A fire extinguisher and first aid kit should be kept readily accessible while
performing maintenance on this mixer/feeder.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
READ THE FOLLOWING BEFORE WELDING ON THIS MIXER/FEEDER
When welding on your mixer/feeder, do not allow the current to flow through the ball
bearings or the roller chains. Ground directly to the item being welded.
Always disconnect the scale instrumentation from the weigh bars or load cells and the
power source. Be sure the current does not pass through weigh bars or load cells or
scale indicator. The alternator should always be disconnected if the mixer/feeder is not
disconnected from the towing vehicle.
CHAIN TENSION
All the single roller chain should be tightened to the point of .042” (1 mm) (dime)
clearance is reached between the coils of the 1-1/4” idler tension springs
and .068” (1.7 mm) (nickel) clearance is reached between the coils of the 1-3/4”
idler tension springs.
LOADING INSTRUCTIONS & PRECAUTIONS
A. Do not add side board extensions to the mixer.
B. Do not overload the mixer. Mixer capacity can be reached by weight or volume.
By volume, the rotor bars and wipers should always be visible at the peak of the
rotor cycle. If the rotor is completely submerged under the mix, mixing efficiency
may be reduced, spillage may occur, and damage to the mixer may result.
Maximum capacity by weight can be calculated by multiplying 28 pounds times
mixer cubic foot capacity.
C. Load molasses and/or liquid protein supplements first with mixer not running, then
add one (1) commodity ingredient before starting the mixer. For the shortest
mixing time and maximum mixing efficiency, these items should be added at the
first of the loading process.
D.
When adding minute supplements or medication in non-liquid form, these
ingredients should be loaded in the middle of the loading sequence.
E. RATIONS WITH GROUND HAY:
1. Load molasses (or liquids) first with the mixer not running.
2. Load one (1) commodity ingredient and start mixer.
3. Finish loading commodities, silage, or ground hay. Loading ground hay after
mixing liquids with another commodity will prevent molasses hay balls.
NOTE: These procedures may not work on all rations. Loading sequences may
be changed to give best possible mix.
ATTENTION:
F. Never load the mixer from the right side (side opposite the discharge) with a front
end loader of payloader.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION:
Trailer mounted mixers can be furnished with single tractor controls or dual controls.
Dual controls are standard unless specified.
1. Single controls operate as follows: Spout goes down first - door opens
second. Door closes first - spout goes up second.
2. The disadvantage of the single control is that it does not let you adjust
the spout height without first closing the door.
ROTO-HAY PROCESSOR
The ROTO-HAY PROCESSOR is designed for processing hay into the mixer. This
eliminates the need for grinding hay, which saves the time and expense of grinding
and can save up to 18% loss from wind and handling.
THE ROTO-HAY PROCESSOR MUST BE PROPERLY USED
ALWAYS USE DRY HAY
Drain rain water out of mixer before use. 1” of rain in a 524-15 equals (72 gal) 586
lbs. of water which will increase the moisture in 1500 lbs. of dry hay (12%) to 37%
moisture or 1000 lbs. of dry hay to 45% moisture.
The ROTO-HAY PROCESSOR will handle small amounts of damp hay, but this is
done at your own risk. ROTO-MIX will not warranty bent or broken rotor tubes, bent or
broken augers, or bent hay pans caused from misuse, wet hay, foreign objects, and/or
overloading.
HAY PREPARATION:
1. SMALL BALES - (60 to 150 lbs., 2 or 3 wire) Remove twine or wire from
bales and break bales apart by pushing into a pole with a front end
loader.
2. LARGE SQUARE BALES - (3’ x 4’ x 8’ or 4’ x 4’ x 8’)
A. Position bale so you can et to end of bale with front end loader.
B. Remove twine or wrapping.
C. With front end loader, pull a 12” flake away from the bale so it can
be picked up with loader bucket - or - by adding 3 or 4 teeth (12”
long) to the top of your loader bucket, you can stab the end of the
bale and pick up a 12” flake to lay on the mixer hay pan.
3. ROUND BALES
A. Remove twine or wrapping.
B. Cut bale with a ROTO-BALE CUTTER a minimum of 5 times to part
the bale into a minimum of 12” chunks. More times may be desired
for ease of handling.
C. Break bales apart by pushing into a pole with a front end loader so
the hay can be loaded in quantities of approximately 200 lbs. at a
time.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADING INSTRUCTIONS FOR HAY PROCESSOR
Load all commodities except liquids on the discharge (auger) side with the hay pan in
the raised position. The raised hay pan does not affect the mixing action
1. If molasses and/or liquid protein is used, load on the rotor side of the mixer
first with the mixer not running.
2. Load one (1) grain or dry commodity in a minimum amount equal to the
amount of hay to be put into mixer with the mixer not running.
3. Start the mixer and run approximately one (1) minute before adding hay.
4. With the mixer running at a minimum rotor speed of 4 RPM, load prepared
hay towards the front of the hay pan on discharge side of mixer. For best
results, when loading with a tractor front end loader or payloader, each
bucket load should not exceed 200 lbs at one time. Allow time for the hay
to be processed into the mixer before loading another 200 lbs. Repeat
until desired amount of hay is processed (DO NOT OVERLOAD). Let the
mixer run until desired length of hay is reached.
5. Finish loading dry commodities.
6. Load wet feeds, such as silage, after all commodities and hay are in the
mixer.
7. If water is to be added to the ration - Do this last!
MIXER INFORMATION
The mixer trailers are equipped with recapped tires with a new tread cap.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
LUBRICATION CHART
DISENGAGE PTO & SHUT OFF POWER BEFORE LUBRICATING THE MACHINE.
LOOSE OR FLOPPY CLOTHING SHOULD NOT BE WORN BY THE OPERATOR.
OIL BATH: Fill the oil bath with 30 weight motor oil to sight plug level.
GREASE BANK: Grease every 100 hours.
FRONT END BEARINGS: Grease every 100 hours.
INPUT BEARINGS: One (1) on input shaft beneath mixer/feeder. Grease every 100
hours.
PTO SHAFTS & U-JOINTS: Grease every 10 to 20 hours.
GEARBOX: Prior to operation, remove the uppermost plug and replace with vent plug
provided. After the first 100 hours of operation, drain the initial oil,
preferably warm. Flush the gear case with an approved non-flammable,
non-toxic solvent and refill with oil. Thereafter oil should be changed
every 2500 hours or every 12 months, whichever occurs first. Fill the
gearbox with 1-1/2 pints of either AGMA 5 EP or GL 90 lube.
SAFETY
READ BEFORE
YOU FEED
SAFETY
READ BEFORE
YOU FEED
SAFETY
READ BEFORE
YOU FEED
24
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 SPECIFICATIONS
Capacity (Cu. ft.).......................................... 520
Struck level capacity (Cu. ft.) ....................... 560
Top Auger Bearing (Front)........................... 2-3/16” 4-Bolt
Top Auger Bearing (Rear)............................ 3” 4-Bolt
Bottom Auger Bearing (Front)...................... 2-7/16” 4-Bolt
Bottom Auger Bearing (Rear) ...................... 3-1/2” 4-Bolt
Rotor Bearing (Front)................................... 2-15/16” 4-Bolt
Rotor Bearing (Rear).................................... 4” 4-Bolt
Top Auger Sprockets ................................... 120 A 26H & 100 A 54
Bottom Auger Sprockets.............................. 120 A 48 & 120 B 13
Rotor Sprocket............................................. 120 A 100
Jackshaft Sprockets..................................... 100 B 17H & 80 B 48 - Trk & Trl 540 PTO
100 B 15H & 80 B 48 - 1000 PTO
Drive Sprockets............................................ 80 B 25H - Trk & Trl 540 PTO
80 B 15H - Trl 1000 PTO
Top Auger Flighting...................................... 3/8” x 20”OD RH 14” Pitch
Bottom Auger Flighting ................................ 1/2” x 20”OD RH & LH Full Pitch
Tub Bottom Construction ............................. 1/4” Steel
Auger Bottom Construction.......................... 1/4” Steel
Right Side Sheet Construction..................... 7GA (3/16”) Steel
Left Side Sheet Construction ....................... 7GA (3/16”) Steel
Front End Sheet Construction...................... 1/4” Steel
Rear End Sheet Construction ...................... 1/4” Steel
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PTO CHART
524-15
PTO
GEARBOX
(RATIO)
INPUT
SPROCKET
JACKSHAFT
SPROCKET
(% ENGINE SPEED)
DIESEL
AUTO
TRANS Engine Rotation
80-85
250 FT./LB MIN.
3:1
25 Tooth
17 Tooth
48 Tooth
FOR OTHER ENGINE OR TRANSMISISSION APPLICATIONS CONSULT FACTORY
1000
TRACTOR
DRIVE
(OPTIONAL)
15 Tooth
15 Tooth
48 Tooth
540
TRACTOR
DRIVE
(STANDARD)
25 Tooth
17 Tooth
48 Tooth
STATIONARY
BELT RATIO
30 HP 5V-2 Groove 16” &
5V-3 Groove 9.25”
2 Belts 5V-1060
25HP 5V-2 Groove 16” &
5V-3 Groove 9.25”
2 Belts 5V-1060
NOTE: IF OPTIONAL HAY PROCESSOR IS INSTALLED A 30HP MOTOR IS REQUIRED.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 TRUCK DIMENSIONS
HEIGHT DIMENSIONS BASED ON 38” TRUCK
FRAME WITH 20” SPOUT STANDARD
108"
(SPOUT CLOSED)
106"
101 1/2"
52"
APPROXIMATE WEIGHT
524-15 ON TRUCK ................ 10,800 LB.
4 1/2"
WITH HAY PROCESSOR ..... 11,550 LB.
OPTIONAL HAY
PROSESSOR
18"
17" SPOUT
45-1/2"
42-1/2"
18"
20" SPOUT
43-1/2"
115"
A
B
C
D
40-1/2"
C
56"
A
B
20-1/2"
22"
24-1/2"
52"
D
96"
215"
2 1/2"
180"
2"
4 3/4"
125"
OPTIONAL HAY PROCESSOR
12"
42"
44"
8"
C
L
C
L
C
L
49"
112"
120" - 126" CA
All Dimensions & Specifications are Approximate and Subject to Change Without Notice
27
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 TRAILER DIMENSIONS
110"
(SPOUT CLOSED)
106"
99"
49"
HEIGHT DIMENSIONS ARE
BASED ON 44” O.D. TIRES
17” SPOUT STANDARD
OPTIONAL HAY
PROSESSOR
18"
APPROXIMATE WEIGHT
524-15 ON TRAILER ......... 12,500 lbs
W/HAY PROCESSOR........ 13,250 lbs
*INCREASE DIMENSIONS BY 4”
W H E N O P T IO N A L R IS E R
BLOCKS ARE INSTALLED.
*107"
48"
C
*A
*B
C
L
47"
47" to 51"
SIDE OF MIXER
17" SPOUT
37-1/2"
20" SPOUT
35-1/2"
94" to 102"
A
B
C
D
34-1/2"
32-1/2"
16" - 20"
20" - 24"
18-1/2" - 22-1/2"
22-1/2" - 26-1/2"
201"
2 1/2"
4 3/4"
180"
125"
2"
OPTIONAL HAY PROCESSOR
12"
44"
46 3/8"
C
L
C
L
C
L
17"
THRU 20"
112"
157" - 176"
256 1/2"
All Dimensions & Specifications are Approximate and Subject to Change Without Notice
28
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 TRAILER DIMENSIONS
(WITH CONVEYOR)
126"
124 1/4"
122 1/2"
106"
7"
OPTIONAL HAY
49"
PROCESSOR
18"
24" CONVEYOR
36" CONVEYOR
48" CONVEYOR
36"
35 1/2"
59 1/2"
40"
54"
44"
48"
C
L
44"
47" to 51"
33" - 35"
94" to 102"
43 1/4" - 45 1/4"
53 1/2" - 55 1/2"
NOTE: UNDERLINED DIMENSIONS ARE WITH
CONVEYOR SET AT ITS MAXIMUM
OPERATING ANGLE OF 30 DEGREES
All Dimensions & Specifications are Approximate and Subject to Change Without Notice
29
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 STATIONARY DIMENSIONS
106"
4 1/2"
52"
OPTIONAL HAY
PROCESSOR
18"
APPROXIMATE WEIGHT, LESS MOTOR
524-15 STATIONARY.................... 10,500 LB.
WITH HAY PROCESSOR.............. 11,250 LB.
59 1/2"
83"
23 1/2"
10 1/2"
21"
180"
2 1/2"
2"
4 3/4"
125"
OPTIONAL HAY PROCESSOR
32"
12"
16 1/2"
30"
22"
128"
38 1/2"
16"
215"
All Dimensions & Specifications are Approximate and Subject to Change Without Notice
30
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 MOUNTING DIMENSIONS
All Dimensions & Specifications are Approximate and Subject to Change Without Notice
31
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 MOUNTING DIMENSIONS
All Dimensions & Specifications are Approximate and Subject to Change Without Notice
32
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS PAGES
TABLE OF CONTENTS
PAGE NO.
WIRING SCHEMATIC FOR STRAIGHT DOOR ............................................................ 34
JOYSTICK ASSEMBLY....................................................................................................... 35
MV5 DOUBLE HYDRAULIC VALVE ASSEMBLY ........................................................ 36
12V DOUBLE HYDRAULIC VALVE ASSEMBLY.......................................................... 37
HYDRAILIC PUMP, TRUCK .............................................................................................. 38
OIL RESERVOIR ASSEMBLY ........................................................................................... 39
HYDRAULIC SCHEMATIC FOR STRAIGHT DOOR.................................................... 40
STATIONARY HYDRAULIC ASSEMBLY ....................................................................... 41
DISCHARGE DOOR ASSEMBLY ...................................................................................... 42
DISCHARGE DOOR HAND WHEEL ASSEMBLY ......................................................... 43
17” SPOUT ASSEMBLY ....................................................................................................... 44
20” SPOUT ASSEMBLY ....................................................................................................... 45
SPOUT MAGNET ASSEMBLY ........................................................................................... 46
SPOUT RUBBER.................................................................................................................... 47
CHAIN CONVEYOR ASSEMBLY....................................................................................48-49
CHAIN CONVEYOR HYDRAULIC ASSEMBLY ............................................................ 50
CONVEYOR HYDRAULIC ASSEMBLY (2 CYLINDER)............................................... 51
SCALE INDICATOR ASSEMBLY...................................................................................... 52
OIL BATH DOOR ASSEMBLY........................................................................................... 53
LUBRICATION ASSEMBLY (OIL BATH)........................................................................ 54
STAGGERED ROTOR ASSEMBLY................................................................................... 55
3 ARM ROTOR ASSEMBLY ............................................................................................... 56
5 ARM ROTOR ASSEMBLY ............................................................................................... 57
TOP & BOTTOM AUGER ASSEMBLY............................................................................. 58
FRONT END BEARING ASSEMBLY ................................................................................ 59
DRIVE ASSEMBLY.............................................................................................................60-61
STATIONARY DRIVE ASSEMBLY.................................................................................62-63
DRIVE LINE GEARBOX ASSEMBLY............................................................................... 64
TRUCK DRIVELINE ASSEMBLY ..................................................................................... 65
TRUCK DRIVESHAFT ASSEMBLY.................................................................................. 66
TRAILER DRIVELINE ASSEMBLY.................................................................................. 67
TRAILER DRIVESHAFT ASSEMBLY.............................................................................. 68
TRAILER LOADCELL SCALE ASSEMBLY.................................................................... 69
TRAILER WEIGH BAR ASSEMBLY ................................................................................ 70
TRUCK LOADCELL SCALE FRAME ASSEMBLY........................................................ 71
TRUCK WEIGH BAR SCALE FRAME ASSEMBLY ...................................................... 72
STATIONARY LOAD CELL SCALE FRAME ASSEMBLY .......................................... 73
TRAILER ASSEMBLY ......................................................................................................... 74
HUB & SPINDLE ASSEMBLY ............................................................................................ 75
ROTO-HAY PROCESSOR ASSEMBLY (HYDRAULIC OPTION)............................... 76
ROTO-HAY PROCESSOR ASSEMBLY............................................................................ 77
ROTO-HAY PROCESSOR ASSEMBLY (CABLE OPTION).......................................... 78
BOTTOM AUGER FLOAT ASSEMBLY ........................................................................... 79
FENDERS & MUD FLAPS ................................................................................................... 80
33
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING SCHEMATIC FOR STRAIGHT DOOR
YELLOW
RED
GREEN
BROWN
RED
YELLOW
GREEN
BROWN
REF. NO PART NO. DESCRIPTION
QTY.
1
A
B
780080
780081
781055
780123
PUSH BUTTON SWITCH PANEL
JOYSTICK PANEL ........................................................... 1
TRUCK TO MIXER WIRE ASSEMBLY ............................ 1
HYDRAULIC CONTROL VALVE...................................... 1
2
3
34
Download from Www.Somanuals.com. All Manuals Search And Download.
JOYSTICK ASSEMBLY
BOTTOM
TOP
TO 12 VOLT
BROWN
YELLOW
RED
GREEN
BROWN
YELLOW
RED
GREEN
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
781056
185575
357705
SWITCH WIRE ASSEMBLY................................................... 1
JOYSTICK BRACKET............................................................. 1
JOYSTICK SWITCH................................................................. 1
35
Download from Www.Somanuals.com. All Manuals Search And Download.
MV5 DOUBLE HYDRAULIC ASSEMBLY
(780123 OLD STYLE)
OUTLET
BUILT IN PRESSURE
RELIEF PRESET TO
1500 PSI
INLET
REF. NO PART NO. DESCRIPTION
QTY.
1
362209
362206
368030
368115
HYDRAULIC VALVE 12V DOUBLE .................................1
12V SING MV5 HYD VLV MVSR 1500-10-50-12-TD.......2
FITTING, 9/16”MOR x 3/8” FPSW 90° .............................4
FITTING, 9/16” MOR x 3/8” FPSW STRT ........................2
1A
2
3
36
Download from Www.Somanuals.com. All Manuals Search And Download.
12V DOUBLE HYDRAULIC ASSEMBLY
(780123 NEW STYLE)
DO NOT USE
THIS POLE
TO JOYSTICK
TO JOYSTICK
DO NOT USE
THIS POLE
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
362209
368115
368024
368030
781057
HYDRAULIC VALVE 12V DOUBLE..................................1
FITTING, 9/16” MOR x 3/8” FPS.......................................2
FITTING, 45° SWIVEL 9/16” MOR x 3/8” FPS..................2
FITTING, 90° SWIVEL 9/16” MOR x 3/8” FPS..................2
SOLENOID GROUND WIRE, 12 VOLT ...........................2
37
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC PUMP, TRUCK (780064)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
336008
324040
189053
362017
368050
368512
368040
BUSHING, SH1/2” QD...................................................... 1
SHEAVE, 1B 4.0” V-BELT................................................ 1
HYDRAULIC PUMP BRACKET........................................ 1
HYDRAULIC PUMP (D17AA2A) ...................................... 1
FITTING, 7/8” MOR x 3/4” FPSW 90° .............................. 1
FITTING, 3/4” MP x 3/4” PUSH LOCK BARB................... 1
FITTING, 3/4” MOR x 3/8” FPSW 90° .............................. 1
38
Download from Www.Somanuals.com. All Manuals Search And Download.
OIL RESERVOIR ASSEMBLY (780205)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
362550
870477
352400
362403
352440
362504
368512
368665
781059
FILLER CAP......................................................................1
OIL RESERVOIR WELDMENT.........................................1
OIL FILTER ASSEMBLY...................................................1
FILTER HEAD
A
B
FILTER ELEMENT
4
5
6
7
SUCTION SCREEN..........................................................1
FITTING, 3/4” MP x 3/4” PUSH LOCK BARB...................1
FITTING, 3/4” x 3/8” REDUCER .......................................1
HYD HOSE ASSEMBLY, 3/8” x 20” x 3/8” ENDS.............1
39
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULIC SCHEMATIC FOR STRAIGHT DOOR
NOTE (C)
NOTE (A)
NOTE (B)
NOTE (D)
NOTE A: CONNECT TO SPOUT CYLINDER BASE
NOTE B: CONNECT TO SPOUT CYLINDER ROD END
NOTE C: CONNECT TO DOOR CYLINDER BASE
NOTE D: CONNECT TO DOOR CYLINDER ROD END
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
780064
780205
780123
781059
184291
781073
781066
781069
781061
781098
HYDRAULIC PUMP ASSEMBLY .............................................1
RESERVOIR ASSEMBLY ........................................................1
HYDRAULIC VALVE ASSEMBLY............................................1
HYD. HOSE ASSY. 3/8” x 20” w/3/8” MP ENDS......................1
HYD. HOSE ASSY. 3/4” x 144” (SUCTION LINE)....................1
HYD. HOSE ASSY. 3/8” x 144” w/3/8” MP ENDS....................1
HYD. HOSE ASSY. w/3/8” MP & 1/4” MP ENDS .....................1
HYD. HOSE ASSY. w/3/8” MP & 1/4” MP ENDS .....................1
HYD. HOSE ASSY. w/3/8” MP ENDS ......................................1
HYD. HOSE ASSY. w/3/8” MP ENDS ......................................1
10
40
Download from Www.Somanuals.com. All Manuals Search And Download.
STATIONARY HYDRAULIC ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
781004
352205
368030
368115
357700
453717
781113
872138
781005
410852
185488
410008
872136
412416
324040
336008
325060
189088
781075
781077
781099
HYDRAULIC VALVE ASSEMBLY............................................ 1
SINGLE HYDRAULIC VALVE, 120V ....................................... 1
FITTING, 9/16” MOR x 3/8” FPSW 90°.................................... 2
FITTING, 9/16” MOR x 3/8” FPSW STRT................................ 2
PENDANT SWITCH WH-4052................................................. 1
WEATHER PROOF BOX......................................................... 1
STATIONARY HYDRAULIC PUMP ASSEMBLY..................... 1
PUMP SWING ARM WELDMENT ........................................... 1
OIL RESERVOIR ASSEMBLY................................................. 1
EYEBOLT, 3/8” X 8”................................................................. 1
2/0 PASSING LINK CHAIN x 18” ............................................. 1
PULL SPRING, 1-1/4” x 5-1/4”................................................. 1
PUMP LEVER ARM WELDMENT............................................ 1
1” SET COLLAR....................................................................... 2
BELT SHEAVE, 1B x 4.0” SH .................................................. 1
BUSHING, SH 1/2” QD ............................................................ 1
V-BELT, B60 ............................................................................ 1
SUCTION HOSE, 3/4” x 94”..................................................... 1
HYD HOSE ASSEMBLY, 3/8” x 180” x 3/8” MP ENDS............ 1
HYD HOSE ASSEMBLY, 3/8” x 192” x 3/8” MP ENDS............ 1
HYD HOSE ASSEMBLY, 3/8” x 120” x 3/8” MP ENDS............ 2
A
B
C
D
E
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
41
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 DISCHARGE DOOR ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
850140
850138
150049
404351
404003
402512
184267
780109
364055
364954
364400
184259
150385
DISCHARGE DOOR WELDMENT................................... 1
DOOR LEVER ARM WELDMENT ................................... 1
DOOR ARM...................................................................... 2
CLEVIS PIN 3/4” X 2-1/2”................................................. 3
COTTER PIN 5/32” X 1 1/4”............................................. 3
FLAT WASHER 3/4” SAE................................................. 3
DOOR CYLINDER MARKER CLAMP.............................. 1
HYDRAULIC CYLINDER 2” X 8” (WITH FITTINGS)........ 1
HYDRAULIC CYLINDER 2” X 8” (CYLINDER ONLY)..... 1
HYDRAULIC CYLINDER ROD 2” X 8” X 1 1/16” ............. 1
HYDRAULIC CYLINDER 2” REPAIR KIT ........................ 1
DOOR CYLINDER MARKER PLATE (TRUCK)............... 1
DOOR MARKER BAR (TRAILER)................................... 1
A
B
C
9
10
42
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 HAND WHEELASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
850079
850145
872030
872349
189105
189106
407047
410305
189112
150387
340216
150244
185114
HAND WHEEL FRAME WELDMENT...................................1
524 STATIONARY DOOR WELDMENT ...............................1
HAND WHEEL WELDMENT..................................................1
BEARING BRAKE MOUNT WELDMENT ............................1
BEARING BRAKE BLOCK UHMW.......................................1
HAND KNOB BOLT SUPPORT ..............................................1
CARRIAGE BOLT 3/8”-16 X 3” ..............................................1
HAND KNOB ............................................................................1
BRAKE ARM ............................................................................1
HAND WHEEL SHAFT............................................................1
FLANGE BEARING VCJT 1” 2-BOLT ...................................2
HAND WHEEL BEARING BLOCK UHMW..........................1
GEAR S1020 X 1” BORE..........................................................1
43
Download from Www.Somanuals.com. All Manuals Search And Download.
17” SPOUT ASSEMBLY
#750044 ..............................17” SPOUT ASSY WITH MAGNET
#750045 ..............................17” SPOUT ASSY NO MAGNET
6
REF. NO PART NO. DESCRIPTION
QTY.
1A
1B
2
3
4
850106
850107
150383
183152
850050
750019
400712
850053
400205
402005
407021
17” SPOUT WELDMENT WITH MAGNET...............................1
17” SPOUT WELDMENT NO MAGNET...................................1
SPOUT PIVOT TUBE...............................................................1
SPOUT BACK-UP ANGLE .......................................................1
SPOUT CYLINDER TOP BRACKET WELDMENT ..................1
SPOUT CYLINDER ASSEMBLY 1-1/2” x 8” ............................1
HEX JAM NUT 3/4”-16 .............................................................1
SPOUT CYLINDER LUG..........................................................1
HEX NUT 5/16”-18...................................................................10
SPLIT LOCKWASHER 5/16”...................................................10
CARRIAGE BOLT 5/16”-18 x 1” ..............................................10
5
5A
5B
6
7
8
44
Download from Www.Somanuals.com. All Manuals Search And Download.
20” SPOUT ASSEMBLY
#750054 ..............................20” SPOUT ASSY WITH MAGNET
#750055 ..............................20” SPOUT ASSY NO MAGNET
6
REF. NO PART NO. DESCRIPTION
QTY.
1A
1B
2
3
4
850093
850094
150383
183152
850050
750019
400712
850053
400205
402005
407021
20” SPOUT WELDMENT WITH MAGNET............................... 1
20” SPOUT WELDMENT NO MAGNET .................................. 1
SPOUT PIVOT TUBE............................................................... 1
SPOUT BACK-UP ANGLE....................................................... 1
SPOUT CYLINDER TOP BRACKET WELDMENT.................. 1
SPOUT CYLINDER ASSEMBLY 1-1/2” x 8”............................ 1
HEX JAM NUT 3/4”-16............................................................. 1
SPOUT CYLINDER LUG ......................................................... 1
HEX NUT 5/16”-18 .................................................................. 10
SPLIT LOCKWASHER 5/16”................................................... 10
CARRIAGE BOLT 5/16”-18 x 1”.............................................. 10
5
5A
5B
6
7
8
45
Download from Www.Somanuals.com. All Manuals Search And Download.
SPOUT MAGNET ASSEMBLY
6
REF. NO PART NO. DESCRIPTION
QTY.
1A
1B
2
3
4
5
6
7
8
850106
850093
150299
357005
400205
402005
402405
407021
407022
17” SPOUT WELDMENT..........................................................1
20” SPOUT WELDMENT..........................................................1
SPOUT MAGNET GUARD.......................................................1
ARCO PLATE MAGNET AM 2200 ...........................................2
HEX NUT, 5/16”-18..................................................................20
LOCKWASHER, 5/16”.............................................................20
FLAT WASHER USS, 5/16”......................................................4
CARRIAGE BOLT, 5/16”-18 x 1” .............................................18
CARRIAGE BOLT, 5/16”-18 x 1-1/4”........................................2
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SPOUT RUBBER
REF. NO PART NO. DESCRIPTION
QTY.
1
A
B
150384
150403
150150
183152
SPOUT RUBBER (17” SPOUT)............................................... 1
SPOUT RUBBER (20” SPOUT)............................................... 1
SPOUT RUBBER END PLATE................................................ 2
SPOUT BACK-UP ANGLE....................................................... 1
2
3
47
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAIN CONVEYOR ASSEMBLY
48
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAIN CONVEYOR ASSEMBLY
#781414 .............. 24”L x 48”W CONVEYOR ASSEMBLY
#781464 .............. 36”L x 48”W CONVEYOR ASSEMBLY
#781465 .............. 48”L x 48”W CONVEYOR ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
160025
188427
188428
340316
402006
405652
400205
402005
407021
409916
188390
874126
874004
874122
874128
874136
874124
188304
188384
188432
188418
874127
874154
874153
341323
400210
400810
760000
8 TOOTH #55 SPROCKET x 1”ID ....................................4
48”W CONVEYOR DRIVE SHAFT ...................................1
48”W CONVEYOR IDLER SHAFT....................................1
RCJC 1” 4-BOLT FLANGE BEARING ..............................2
SPLIT LOCKWASHER, 3/8” .............................................8
HHCS, 3/8”-16 x 3/4”.........................................................8
HEX NUT, 5/16”-18..........................................................20
SPLIT LOCKWASHER, 5/16” .........................................20
CARRIAGE BOLT, 5/16”-18 x 1”......................................20
WOODRUFF KEY, 1/4” x 1”..............................................4
CONVEYOR TAKE-UP BOLT...........................................2
24”L x 48”W CONVEYOR PAN WELDMENT
10
11
12
36”L x 48”W CONVEYOR PAN WELDMENT
48”L x 48W CONVEYOR PAN WELDMENT ....................1
24”L x 48”W CONVEYOR WELDMENT
13
36”L x 48”W CONVEYOR WELDMENT
48”L x 48”W CONVEYOR WELDMENT ...........................1
CONVEYOR SPOUT RUBBER BAR - 4” .........................2
CONVEYOR SPOUT RUBBER BAR - 45-3/4” .................1
48”W CONVEYOR SPOUT RUBBER...............................1
CONVEYOR SPOUT RUBBER SIDE BAR ......................2
24”L x 48”W CONV. C55 CHAIN WELDMENT
14
15
16
17
18
36”L x 48”W CONV. C55 CHAIN WELDMENT
48”L x 48”W CONV. C55 CHAIN WELDMENT.................1
TAKE-UP BEARING, 1” ....................................................2
HEX NUT, 5/8”-11.............................................................6
UNILOCK, 5/8”-11.............................................................2
TAKE-UP BEARING ASSY (INCLUDES 11, 19 & 21)......2
19
20
21
22
49
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAIN CONVEYOR HYDRAULIC ASSEMBLY
TO
TO
TRACTOR
MOTOR
TO CONV
DOWN
TO
TRACTOR
FRONT
END SHEET
TO MOTOR
PORT B
10
TO CONV UP
B
A
CONVEYOR CYLINDER
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
874071
781329
781328
781327
781236
409916
368608
368118
368031
368028
368007
364060
362283
362240
360009
332654
310805
CONVEYOR MOTOR PLATE WELDMENT .........................1
HYD. HOSE ASSY 3/8” X 125” (3/8”MP ENDS) ...................1
HYD. HOSE ASSY 1/2” X 128” (1/2”MP ENDS) ...................2
HYD. HOSE ASSY 1/2” X 56” (1/2”MP ENDS) .....................2
HYD. HOSE ASSY 3/8” X 112” (3/8”MP ENDS) ...................1
WOODRUFF KEY 1/4” X 1”....................................................1
FITTING, 1/2”MP X 1/2”FP X 1/2”FP TEE.............................3
FITTING, 7/8”MOR X 1/2”FPSW ............................................2
FITTING, 1/2”MP X 1/2”FPSW 90°.........................................4
FITTING, 1/2” X 3/8”FPSW .....................................................2
FITTING, 3/8”MP X 3/8”FPSW 90° .109” ORFICE................2
HYDRAULLIC CYLINDER 2” X 16” .....................................1
HYDRAULIC FLOW CONTROL VALVE..............................1
BALL CHECK VALVE 1/2”FP X 1/2”FP................................1
HYDRAULIC MOTOR, 9.7 CI.................................................1
KEY, 1”ID X 2”OD X 3”LTB CPLG W/1/4” ...........................1
CLOSE NIPPLE, 1/2”................................................................1
50
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVEYOR HYDRAULIC ASSEMBLY (TWO CYLINDERS)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
781355
781328
781337
781356
781067
368608
368118
368031
368028
368007
364060
362283
362240
310805
874071
409916
332654
360009
368607
368110
HYD HOSE ASSY 3/8” x 105” (3/8” MP ENDS)............... 1
HYD. HOSE ASSY 1/2” x 128” (1/2”MP ENDS)............... 2
HYD. HOSE ASSY 1/2” x 80” (1/2”MP ENDS)................. 2
HYD. HOSE ASSY 3/8” x 81” (3/8”MP ENDS)................. 2
HYD. HOSE ASSY 3/8” x 60” (3/8”MP ENDS)................. 1
SERVICE TEE, 1/2”MP x 1/2”FP x 1/2”FP....................... 3
STRT. ADAPTER, 7/8”MOR x 1/2”FPS ........................... 2
FITTING, 1/2”MP x 1/2”FPSW 90°................................... 4
FITTING, 1/2” x 3/8”FPSW 90° ........................................ 2
FITTING, 3/8”MP x 3/8”FPSW 90° .109” ORFICE ........... 4
HYDRAULIC CYLINDER 2” x 16” - 26-1/4” CC ............... 1
HYDRAULIC FLOW CONTROL VALVE.......................... 1
BALL CHECK VALVE 1/2”FP x 1/2”FP............................ 1
CLOSE NIPPLE, 1/2” ....................................................... 1
CONVEYOR MOTOR PLATE WELDMENT .................... 1
WOODRUFF KEY, 1/4” x 1”............................................. 1
MOTOR COUPLING, 1”ID x 2”OD x 3”LTB, W1/4” KEY.. 1
HYDRAULIC MOTOR, 9.7 CI........................................... 1
SERVICE TEE, 3/8”MP x 3/8”FP x 3/8”FP....................... 2
STRT. ADAPTER, 3/8”MP x 3/8”FPSW........................... 2
9
10
11
12
13
14
15
16
17
18
19
20
51
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 SCALE INDICATOR ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
872125
872126
185490
185491
185493
185303
184283
185492
401108
405714
400206
402006
405653
400906
405661
412205
TRAILER SCALE ARM WELDMENT ...................................1
TRAILER SCALE INDICATOR WELDMENT.......................1
TRAILER SCALE INDICATOR TUBE...................................1
HINGE PLATE ..........................................................................2
HINGE WASHER......................................................................2
TRAILER SCALE ARM ANGLE.............................................2
HOSE CARRIER .......................................................................1
LOCKING HANDLE 1/2”.........................................................1
HEX LOCKNUT, 1/2”...............................................................1
HHCS, 1/2” x 4-1/2” ..................................................................1
HEX NUT, 3/8”..........................................................................4
LOCKWASHER, 3/8” ...............................................................4
HHCS, 3/8” x 1”.........................................................................4
HEX LOCKNUT, 3/8”...............................................................4
HHCS, 3/8” x 3”.........................................................................1
CABLE CLAMP, 3/8” ...............................................................1
52
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 OIL BATH DOOR ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
351056
370323
370322
370321
370320
370319
370317
370316
189503
872639
850585
850586
850575
850574
RUBBER BULB SEAL, 5/32” ................................................ 27’
LEVELING PAD .......................................................................4
HANDLE STOP.........................................................................2
CAM LOCK BUSHING ............................................................2
HANDLE CAM LOCK..............................................................2
CAM LOCK HANDLE..............................................................2
CAM LOCK BOTTOM PLATE................................................4
CAM LOCK TOP PLATE.........................................................4
CAM LOCK SPACER...............................................................4
OIL BATH CENTER CHANNEL.............................................1
524 LARGE OIL BATH DOOR................................................1
514 SMALL OIL BATH DOOR................................................1
CAM ROD, LEFT DOOR..........................................................1
CAM ROD, RIGHT DOOR.......................................................1
53
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 LUBRICATION ASSEMBLY
VIEW A-A
A
A
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
310750
356001
150212
1/8” PTF GREASE ZERK .........................................................6
1/8” NFPT x 3/16” COMP. 90°.................................................12
3/16” COPPER GREASE LINE X 69”......................................2
INPUT SHAFT BEARING
A
E
ROTOR BEARING
4
B
5
C
D
185044
185341
3/16” COPPER GREASE LINE X 39”......................................1
FRONT JACKSHAFT BEARING
3/16” COPPER GREASE LINE X 48”......................................2
REAR JACKSHAFT BEARING
TOP AUGER BEARING
6
F
150211
3/16” COPPER GREASE LINE X 18”......................................1
BOTTOM AUGER BEARING
54
Download from Www.Somanuals.com. All Manuals Search And Download.
524-15 STAGGERED ROTOR
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
190338
190339P
407322
401106
402406
407102
400908
402408
850544
872874
780078
WIPER CHANNEL 12-13/16"x32"..........................................18
PLASTIC WIPER 10-7/8" x 35-1/4" ........................................18
ELEVATOR BOLT PLTD 3/8" x 1-1/4".................................108
3/8" - 16 HEX NYLOC NUT #5 PLTD...................................108
FLAT WASHER, 3/8" ID x 1" OD .........................................108
CAR BOLT, 1/2"-13 X 1-1/2" ..................................................72
1/2"-13 HEX-C LOCKNUT......................................................72
FLAT WASHER, 1/2" ID x 1-3/8" OD ....................................72
524 ROTOR SHAFT FLANGE WA .........................................1
524-15 STAGGERED ROTOR WA..........................................1
STAGGERED WIPER BUNDLE (INCLUDES 1 THRU 8) ....1
10
11
55
Download from Www.Somanuals.com. All Manuals Search And Download.
3 ARM ROTOR ASSEMBLY
(FROM SERIAL #890573481 TO PRESENT)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
850122
850125
850007
150344
150343
150346
150345
410005
406489
400912
401106
405654
850544
750030
524 3-ARM ROTOR WELDMENT ..........................................1
524 WIPER TUBE WELDMENT .............................................3
ROTOR SPRING COVER WELDMENT.................................6
END WIPER STRAP.................................................................6
CENTER WIPER STRAP..........................................................3
END PLASTIC WIPER .............................................................6
CENTER PLASTIC WIPER......................................................3
2 1/2” X 24” X .410” COMPRESSION SPRING......................6
3/4”-10 x 6” HHCS ....................................................................6
3/4”-10 HEX CTR LOCKNUT..................................................6
3/8”-16 NYLOCK HEX NUT...................................................66
3/8”-16 x 1-1/4” HHCS.............................................................66
ROTOR SHAFT FLANGE WELDMENT ................................1
WIPER ASSEMBLY (INCLUDES #’s 2,4,5,6,7,11& 12).....3
56
Download from Www.Somanuals.com. All Manuals Search And Download.
5 ARM ROTOR ASSEMBLY
(FROM SERIAL #890573481 TO PRESENT)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
850248
850125
850007
150344
189343
150346
150345
410005
406489
400912
401106
405654
850544
750030
524 5-ARM ROTOR WELDMENT ..........................................1
524 WIPER TUBE WELDMENT .............................................5
ROTOR SPRING COVER WELDMENT................................10
END WIPER STRAP................................................................10
CENTER WIPER STRAP..........................................................5
END PLASTIC WIPER ............................................................10
CENTER PLASTIC WIPER......................................................5
2 1/2” x 24” X .410” COMPRESSION SPRING .....................10
5/8”-10 x 6” HHCS ...................................................................10
3/4”-10 HEX CTR LOCKNUT.................................................10
3/8”-16 NYLOCK HEX NUT..................................................110
3/8”-16 x 1-1/4” HHCS............................................................110
ROTOR SHAFT FLANGE WELDMENT ................................1
WIPER ASSEMBLY (INCLUDES #’s 2,4,5,6,7,11 &12).....5
57
Download from Www.Somanuals.com. All Manuals Search And Download.
524 TOP & BOTTOM AUGER ASSEMBLIES
(FROM SERIAL #890573481 TO PRESENT)
TOP AUGER
TOP AUGER
(OPTIONAL)
BOTTOM AUGER
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
850131
382026
150126
850542
850131B
382026
381625
382023
150126
850127
382021
382020
150411
850543
TOP AUGER 3/8” FLIGHT WELDMENT ..........................1
FLIGHT RH 20”OD x 6 5/8”ID x 3/8” x 14” PITCH ............9-1/2
TOP AUGER PADDLE.............................................................3
TOP AUGER SHAFT FLANGE WELDMENT .......................1
TOP AUGER DOUBLE FLIGHT WELDMENT.................1
FLIGHT RH 20”OD x 6-5/8”ID x 3/8” x 14” PITCH..............11
FLIGHT RH 16”OD x 6-5/8”ID x 1/4” x 14” PITCH..............11
FLIGHT LH 20”OD x 6-5/8”ID x 3/8” x 20” PITCH ............ 1/2
TOP AUGER PADDLE.............................................................3
BOTTOM AUGER 1/2” FLIGHT WELDMENT.................1
FLIGHT LH 20”OD x 6-5/8”ID x 1/2” x 20” PITCH ...............7
FLIGHT RH 20”OD x 6-5/8”ID x 1/2” x 20” PITCH...............1
20” AUGER KICKER................................................................2
BOTTOM AUGER SHAFT FLANGE WELDMENT..............1
58
Download from Www.Somanuals.com. All Manuals Search And Download.
524 FRONT END ASSEMBLY
(FROM SERIAL #890573481 TO PRESENT)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
340436
340437
340446
LB F3Y235N 2-3/16” 4-BOLT FLANGE BEARING ..............1
LB F3Y239N 2-7/16” 4-BOLT FLANGE BEARING ..............1
LB F247 2-15/16” 4-BOLT FLANGE BEARING ....................1
59
Download from Www.Somanuals.com. All Manuals Search And Download.
524 DRIVE ASSEMBLY (FROM SERIAL #890573481 TO PRESENT)
60
Download from Www.Somanuals.com. All Manuals Search And Download.
524 DRIVE ASSEMBLY (FROM SERIAL #890573481 TO PRESENT)
61
Download from Www.Somanuals.com. All Manuals Search And Download.
524 STATIONARY DRIVE ASSEMBLY
62
Download from Www.Somanuals.com. All Manuals Search And Download.
524 STATIONARY DRIVE ASSEMBLY
63
Download from Www.Somanuals.com. All Manuals Search And Download.
524 200 SERIES 3:1 GEARBOX ASSEMBLY (#344023)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
344214
344215
344211
344210
344220
344213
344209
344223
344219
344212
CLOSED END CAP...................................................................2
END CAP GASKET ..................................................................4
BOX BEARING CUP 18620.....................................................4
GEARBOX BEARING 1-3/4” T-18690....................................4
3:1 LOW SPEED GEAR............................................................1
OPEN END CAP 02-23-00166-400..........................................2
GEARBOX SEAL 1 3/4” CR 18039..........................................2
LOW SPEED SHAFT 1 3/4” .....................................................1
3:1 1-3/8” HIGH SPEED SHAFT & GEAR COMPLETE........1
CENTER CASE GASKET 02-23-00919-200...........................1
10
64
Download from Www.Somanuals.com. All Manuals Search And Download.
524 TRUCK DRIVELINE ASSEMBLY
ITEMS 1 & 5 ARE CUT TO LENGTH
AND WELDED AT INSTALLATION.
CHECK OIL HERE
REF. NO PART NO. DESCRIPTION
QTY.
1
780486
338420
338435
338053
338422
183327
340221
183319
780494
338422
338435
338053
344023
183251
338042
338449
338443
338451
1280 DRIVESHAFT ASSY. 1-1/4” x 1-3/8” ............................. 1
1-1/4” SPICER YOKE............................................................... 1
SPICER 1280 CROSS KIT....................................................... 2
SPICER DRIVESHAFT SPLINE TUBE ASSY ......................... 1
1-3/8” SPICER YOKE............................................................... 1
TRUCK JACKSHAFT 1-3/8”..................................................... 1
1-3/8” FX3W222E 2-BOLT FLANGE BEARING ...................... 2
TRUCK JACKSHAFT BRACKET............................................. 2
1280 DRIVESHAFT ASSY 1-3/8” x 1-3/8” ............................... 1
1-3/8” SPICER YOKE............................................................... 2
SPICER 1280 CROSS KIT....................................................... 2
SPICER DRIVESHAFT SPLINE TUBE ASSY ......................... 1
3:1 HUB CITY GEARBOX........................................................ 1
GEARBOX PLATE ................................................................... 1
W-2400 385560 DRIVESHAFT................................................ 1
W-2400 YOKE 1-3/4” RB, 1/2 SET SCREW............................ 1
W-2400 312410 CROSS KIT ................................................... 2
W-2400 1-3/4” RB YOKE, SET SCREW & BOLT .................... 1
A
B
C
D
2
3
4
5
A
B
C
6
7
8
A
B
C
65
Download from Www.Somanuals.com. All Manuals Search And Download.
524 TRUCK W-2400 DRIVESHAFT ASSEMBLY (#385560)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
338451
338443
338473
338450
338447
338448
338452
338449
W-2400 YOKE 1-3/4”RB 3/8” KEYWAY ...................................1
W-2400 CROSS KIT.................................................................2
WALTERSHIED #10 METRIC ROLL PIN.................................2
W-2400 INBOARD YOKE.........................................................1
W-2400 OUTER PROFILE 2aL ................................................1
W-2400 INNER PROFILE 1b....................................................1
W-2400 INBOARD YOKE 2A ...................................................1
W-2400 YOKE 1-3/4”RB 3/8” KEYWAY ...................................1
66
Download from Www.Somanuals.com. All Manuals Search And Download.
540 & 1000 TRAILER PTO DRIVELINE ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
332612
185480
320720
340229
183277
341028
150386
850136
185299
780601
338030
338442
60 B 20 x 1-3/4” CHAIN COUPLING SPRKT........................... 2
3/8” SQ. KEY x 2”..................................................................... 3
#60-2 RC x 20 PITCHES COMP.............................................. 1
1-3/4” FX3W228U 2-BOLT FLANGE BEARING ...................... 3
BEARING HANGER TRAILER UNIT ....................................... 1
1-3/4” PABCO BKP28T-TP W/BRG......................................... 1
524 DRIVELINE-147”............................................................... 1
524 TRAILER BEARING PLATE WELDMENT........................ 1
CARRIER BEARING ANGLE................................................... 1
PTO SHIELD ASSEMBLY........................................................ 1
W-2400 383399 DRIVESHAFT-540......................................... 1
W-2400 019516 YOKE 1000 RPM........................................... 1
10
11
12
67
Download from Www.Somanuals.com. All Manuals Search And Download.
524 TRAILER DRIVESHAFT W-2400 (#383399)
REF. NO PART NO. DESCRIPTION
YOKE (TRACTOR END)
QTY.
1
A
B
2
3
4
5
6
7
8
338444
338442
338443
338473
338450
338474
338467
338452
338449
338486
338487
338488
338489
YOKE 540 RPM .......................................................................1
YOKE 1000 RPM .....................................................................1
CROSS KIT ...............................................................................2
ROLL PIN METRIC #10...........................................................2
INBOARD YOKE (TRACTOR END) ......................................1
INNER PROFILE (TRACTOR END).......................................1
OUTER PROFILE (MIXER END)............................................1
INBOARD YOKE (MIXER END)............................................1
YOKE (MIXER END) ...............................................................1
SHIELD CONE 9-RIB...............................................................2
OUTER SHIELD TUBE (TRACTOR END) ............................1
INNER SHIELD TUBE (MIXER END) ...................................1
BEARING RING .......................................................................2
9
10
11
12
68
Download from Www.Somanuals.com. All Manuals Search And Download.
524 TRAILER LOADCELL SCALE PARTS
LOADCELL
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
182881
182915
185997
870501
872245
870519
SCALE MOUNT MIXER PAD................................................... 4
LOADCELL CAGE PLATE....................................................... 8
3/8” SCALE PAD...................................................................... 8
CHECK ROD WELDMENT ...................................................... 2
OFFSET CHECK ROD WELDMENT....................................... 2
MIXER SCALE CHECK WELDMENT...................................... 2
69
Download from Www.Somanuals.com. All Manuals Search And Download.
524 TRAILER WIEGH BAR ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
189294
872360
860055
WEIGH BAR MIXER PAD ........................................................4
2-1/2” T-BAR WELDMENT.......................................................4
2-1/2” BAR BLOCK WELDMENT .............................................4
70
Download from Www.Somanuals.com. All Manuals Search And Download.
524 TRUCK SCALE FRAME ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
870527
182998
870519
872053
870501
182881
182915
185997
SCALE FRAME WELDMENT................................................... 1
TRUCK FRAME BRACKET...................................................... 4
MIXER CHECK WELDMENT................................................... 2
OFFSET CHECK ROD............................................................. 1
CHECK ROD............................................................................ 3
SCALE MOUNT MIXER PLATE............................................... 4
LOADCELL CAGE PLATE ....................................................... 8
SCALE PAD ............................................................................. 8
71
Download from Www.Somanuals.com. All Manuals Search And Download.
524 TRUCK 2-1/2” WEIGH BAR SCALE FRAME ASSEMBLY
WELDED TO MIXER BASE
AT INSTALLATION
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
872163
872159
182998
185609
524 TRUCK WEIGH BAR FRAME......................................... 1
2-1/2” WEIGH BAR MOUNT WELDMENT .......................... 4
TRUCK FRAME BRACKET.................................................... 4
BART MOUNT MIXER PAD................................................... 4
72
Download from Www.Somanuals.com. All Manuals Search And Download.
524 STATIONARY LOAD CELL SCALE FRAME ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
850150
870501
871053
870519
182881
182915
185997
524 STATIONARY SCALE FRAME WELDMENT ................... 1
SCALE CHECK ROD WELDMENT ......................................... 2
TRAILER CHECK ROD WELDMENT...................................... 2
MIXER SCALE CHECK WELDMENT...................................... 2
SCALE MIXER MOUNT PLATE............................................... 4
LOADCELL CAGE PLATE....................................................... 8
SCALE PAD ............................................................................. 8
73
Download from Www.Somanuals.com. All Manuals Search And Download.
524 TRAILER ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
2A
2B
3
4
5
6
7
8
9
10A
10B
781145
651024
374100
374101
357400
870972
870733
184598
870931
750111
840110
374002
374001
18.5 x 22.5 MOUNTED TIRE ASSEMBLY ...............................2
PERFECT HITCH KIT (INCLUDES 2A & 2B)...........................1
BASE HITCH BODY .................................................................1
CLEVIS INSERT.......................................................................1
BATTERY BOX WITH STRAP..................................................1
TRAILER AXLE WELDMENT...................................................1
TRAILER BUMPER WELDMENT.............................................1
TRAILER BUMPER EXTENSION.............................................2
TRAILER FRAME WELDMENT................................................1
TRAILER HUB & SPINDLE - 10 BOLT LEFT HAND................1
TRAILER HUB & SPINDLE - 10 BOLT RIGHT HAND .............1
5000 LB. G&G JACK ................................................................1
9000 LB. DROP LEG JACK......................................................1
74
Download from Www.Somanuals.com. All Manuals Search And Download.
10-BOLT HUB & SPINLDE ASSEMBLY (20,000 LB.)
RIGHT HAND ASSY COMPLETE - #750110
LEFT HAND ASSY COMPLETE - #750111
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
342213
342214
342215
342216
184614
372211
372212
372304
372309
400033
400034
400102
400103
402005
402904
405625
407724
407725
BEARING, 3.543” BORE, TIMKEN #HM 218248..................... 1
BEARING, 2.625” BORE, TIMKEN #HM 212049..................... 1
BEARING CUP, 5.787” OD, TIMKEN #HM218210.................. 1
BEARING CUP, 4.813” OD, TIMKEN #212011 ....................... 1
SPINDLE, 4-9/16” x 25-1/2”, 20,000 LB................................... 1
HUB, LEFT HAND, 10-BOLT, 20,000 LB................................. 1
HUB, RIGHT HAND, 10-BOLT, 20,000 LB .............................. 1
SEAL, 4.563” x 6.001”, #CR43771........................................... 1
DUST CAP, 20,000 LB HUB .................................................... 1
OUTER NUT, 3/8” THICK x 2-5/8” ID....................................... 1
INNER NUT, 3/8” THICK x 3-5/8” ID........................................ 1
LUG NUT, RIGHT HAND, 3/4”................................................ 10
LUG NUT, LEFT HAND, 3/4” .................................................. 10
LOCKWASHER, 5/16”.............................................................. 6
WASHER, 1/4” THICK x 2-41/64” ID........................................ 1
HHCS, 5/16” x 1/2”................................................................... 6
STUD BOLT, 3/4” x 2-9/16”, RIGHT HAND ............................ 10
STUD BOLT, 3/4” x 2-9/16”, LEFT HAND............................... 10
75
Download from Www.Somanuals.com. All Manuals Search And Download.
524 ROTO-HAY PROCESSOR ASSEMBLY (HYDRAULIC OPTION)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
188226
357702
780124
780109
368007
364954
364055
354400
781055
850060
872357
781070
781097
FEEDER ELECTRIC CONTROL BRACKET............................1
PUCH BUTTON SWITCH 12V-2 POLE ...................................1
MV5 3rd VALVE ADD ON KIT..................................................1
CYLINDER ASSY, 2” x 8”.........................................................1
RESTRICTOR FITTING, 3/8” MP x 3/8” FPSW 90°.................2
CYLINDER ROD, 2” x 8” x 1-1/16” DIA ....................................1
CYLINDER, 2” x 8” STROKE....................................................1
REPAIR KIT, 2” HYDRAULIC CYLINDER................................1
TRUCK TO MIXER WIRE ASSEMBLY ....................................1
HAY PAN HYD. CYL. BRACKET WELDMENT........................1
HAY PAN HYDRAULIC ARM WELDMENT..............................1
HYDRAULIC HOSE ASSY, 3/8” x 87” x 3/8” MP ENDS...........1
HYDRAULIC HOSE ASSY, 3/8” x 68” x 38” MP ENDS............1
4A
4B
4C
4D
5
6
7
8
9
76
Download from Www.Somanuals.com. All Manuals Search And Download.
524 ROTO-HAY PROCESSOR ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
872351
850144
150198
850301
189127
872355
850302
872354
189128
150817
872353
150223
385002
524 HAY PAN WELDMENT ................................................... 1
524 HAY PAN TUBE WELDMENT........................................ 1
BAFFLE PLUNGER ................................................................. 1
524 CROSS BAR WELDMENT............................................... 1
HAY TUBE SLEEVE RETAINER........................................... 1
HAY PAN CENTER BEARING WELDMENT....................... 1
524 HAY PAN BAFFLE WELDMENT ................................... 1
HAY PAN REAR BEARING WELDMENT............................ 1
CROSS BAR PLATE ................................................................ 1
HAY PAN ANGLE.................................................................... 1
HAY PAN FRONT BEARING WELDMENT ......................... 1
KNIFE BACK-UP PLATE....................................................... 43
SICKLE SECTION, HARD SURFACED................................ 43
77
Download from Www.Somanuals.com. All Manuals Search And Download.
524 ROTOR-HAY PROCESSOR (CABLE OPTION)
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
150188
150189
150190
412204
412325
850066
150186
850090
850105
150228
410009
150391
411805
CABLE BAR..............................................................................2
SLEEVE....................................................................................1
CABLE ......................................................................................1
CABLE CLAMP, 1/4”.................................................................2
CABLE BRAKE WINCH, 1000LB. ............................................1
CABLE PULLEY BRACKET WELDMENT................................1
CABLE WINCH MOUNT PLATE ..............................................1
HAY PAN CABLE ARM WELDMENT.......................................1
CORNER PULLEY BRACKET WELDMENT............................1
PULLEY BACKUP PLATE........................................................1
PULL SPRING, 1-1/4”OD x 14” x .177” ....................................1
SPRING PULL BAR..................................................................1
S-HOOK, 5/16”..........................................................................1
78
Download from Www.Somanuals.com. All Manuals Search And Download.
524 BOTTOM AUGER FLOAT ASSEMBLY
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
9
850153
850154
150418
405752
405656
405655
402406
402006
402010
400210
400206
BEARING SLIDE PLATE WELDMENT 2-7/16” ...................1
BEARING SLIDE FRAME WELDMENT ...............................1
BEARING SLIDER PLASTIC..................................................2
HHCS 5/8” X 1 1/2”...................................................................5
HHCS 3/8” X 1 3/4”...................................................................2
HHCS 3/8” X 1 1/2”...................................................................2
FLAT WASHER 3/8” ................................................................4
LACK WASHER 3/8” ...............................................................5
LOCK WASHER 5/8” ...............................................................4
HEX NUT 5/8”...........................................................................5
HEX NUT 3/8”...........................................................................4
10
11
79
Download from Www.Somanuals.com. All Manuals Search And Download.
524 FENDERS & MUD FLAPS
REF. NO PART NO. DESCRIPTION
QTY.
1
2
3
4
5
872108
183087
370202
370200
872120
FENDER WELDMENT.............................................................2
MUD FLAP STRAP ..................................................................4
FRONT MUD STRAP ...............................................................2
REAR MUD STRAP..................................................................2
MUD FLAP BRACKET WELDMENT ....................................2
80
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Bionaire Fan BAFE1407 User Manual
Bosch Appliances Security Camera NIN 733 User Manual
Bosch Appliances Security Camera VG4 User Manual
Bradford White Corp Water Heater 238 37281 00R User Manual
Braun Electric Toothbrush 3757 User Manual
Breville Juicer JE95 User Manual
Canon Automobile Electronics YJ19X9B IRS User Manual
Cary Audio Design Stereo Amplifier SLP 88 User Manual
CDA Stove HCG602 User Manual
Chromalox Thermostat GNIT 5 User Manual