Model # LCS120
20V MAX* LITHIUM CORDLESS
CHAIN SAW INSTRUCTION MANUAL
Model Number LCS120
Thank you for choosing Black & Decker! Go
to register your new product.
PLEASE READ BEFORE RETURNING
KEY IN
FORM
ATION
YOU S
HOUL
D KNO
W:
THIS PRODUCT FOR ANY REASON:
If you have a question or experience a problem with your
Black & Decker purchase, go to
• DO NOT
OVER-TENSION
CHAIN.
Refer to
"ADJUSTING
CHAIN
TENSION"
for proper
method
of tensioning
chain.
two hours
of use.
WWW.BLACKANDDECKER.COM/INSTANTANSWERS
for instant answers 24 hours a day.
• Retighten
chain frequently
during first
If you canʼt find the answer or do not have access to the internet,
call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. - Fri
to speak with an agent.
Please have the catalog number available when you call.
*Maximum initial battery pack voltage
(measured without a workload) is 20
volts. Measured under a workload,
nominal voltage is 18.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
POUR LE FRANÇAIS, VOIR LA COUVERTURE ARRIÈRE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
Download from Www.Somanuals.com. All Manuals Search And Download.
upper portion of the tip of the guide bar contacts an object, such
as a log or branch.
SAFETY INSTRUCTIONS AND
WARNINGS FOR CHAIN SAWS
•
•
Limbing - Removing the branches from a fallen tree
Low-Kickback Chain - A chain that complies with the kickback
performance requirements of ANSI B175.1-1991 (when tested on
a representative sample of chain saws.)
• Keep Work Area Clean -Cluttered areas invite injuries. Do not
start cutting until you have a clear work area, secure footing, and a
planned retreat path from the falling tree.
•
Normal Cutting Position - Those positions assumed in
performing the bucking and felling cuts.
• Consider Work Area Environment - Use extreme caution when
cutting small size brush and saplings because the slender material
may catch the saw chain and be whipped toward you or pull you off
balance. When cutting a limb that is under tension be alert for spring
back so that you will not be struck when the tension in the wood
fibers is released. Do not expose chain saw to rain or snow. Do not
use chain saw in damp or wet locations or while it is raining or
snowing. Do not use chain saw in the presence of flammable liquids
or gases or enclosed concentrations of dust. Cut only when visibility
and light are sufficient to see clearly
•
•
•
Notching Undercut - A notch cut in a tree that directs the treeʼs fall.
Oiler Control - A system for oiling the guide bar and saw chain.
Rear Handle - The support handle located at or toward the rear
of the saw.
•
•
Reduced Kickback Guide Bar - A guide bar which has been
demonstrated to reduce kickback significantly.
Replacement Saw Chain - A chain that complies with kickback
performance requirements of ANSI B175.1-2000 when tested
with specific chain saws. It may not meet the ANSI performance
requirements when used with other saws.
• Keep Children, Bystanders, Visitors and Animals Away - Do
not let visitors contact chain saw. All visitors should be kept away
from work area.
•
Saw Chain - A loop of chain having cutting teeth, that cut the
wood,and that is driven by the motor and is supported by the
guide bar.
• Store Idle Chain Saw - When not in use, chain saws should be
stored in a dry, and high or locked-up place - out of the reach of
children. When storing saw, always remove battery and use a
scabbard or carrying case.
•
•
•
•
Ribbed Bumper - The ribs used when felling or bucking to pivot
the saw and maintain position while sawing.
• Don't Force Chain Saw - It will do the job better and safer at the
rate for which it was intended.
Switch - A device that when operated will complete or interrupt
an electrical power circuit to the motor of the chain saw.
Switch Linkage - The mechanism that transmits motion from a
trigger to the switch.
• Use Right Tool - Cut wood only. Don't use chain saw for purpose
not intended - for example - Don't use chain saw for cutting plastic,
metal, masonry, non-wood building materials.
Switch Lockout - A movable stop that prevents the unintentional
operation of the switch until manually actuated.
• Dress Properly - Do not wear loose clothing or jewelry. Keep your
hair, clothing, and gloves away from moving parts. Loose clothing,
jewelry, or long hair can be caught in moving parts. Wear protective
hair covering to contain long hair. Air vents cover moving parts and
should be avoided. Protective non-slip gloves and non-skid footwear
are recommended when working outdoors. Always wear heavy,
long pants or other protection for your legs.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using a battery operated chain saw, basic
safety precautions should always be followed to reduce risk of fire,
electric shock, and personal injury, including the following:
• Use Safety Glasses - Also use safety footwear; snug fitting
clothing; protective gloves; proper hearing, respiratory, and head
protection.
READ ALL INSTRUCTIONS
• Carrying Saw - Carry the chain saw by the front handle with the
3
Download from Www.Somanuals.com. All Manuals Search And Download.
saw stopped, finger off the switch, the guide bar and saw chain to
the rear. Remove battery and use scabbard when transporting saw.
• Maintain Chain Saw With Care - Keep tools sharp and clean for
better and safer performance. Follow instructions for lubricating and
changing accessories. Keep handles dry, clean, and free from oil
and grease.
The following precautions should be followed to minimize
kickback:
(1.) Grip Saw Firmly. Hold the chain saw firmly with both hands
when the motor is running. Use a firm grip with thumbs and fingers
encircling the chain saw handles. Chain saw will pull forward when
cutting on the bottom edge of the bar, and push backward when
cutting along the top edge of the bar.
• Disconnect Battery - Disconnect battery from chain saw when
not in use, before servicing, when tensioning chain, and when
changing accessories and attachments, such as saw chain.
• Stay Alert - Watch what you are doing. Use common sense. Do
not operate chain saw when you are tired, ill, or under the influence
of alcohol, drugs, or medication. Keep all parts of the body away
from the saw chain when the motor is operating. Before you start
the saw, make sure the saw chain is not contacting anything. When
cutting through wood, remember the chain saw cuts quickly and will
continue its downward or upward path. Stay out of its path.
• Check Damaged Parts - Before further use of the chain saw, any
part that is damaged should be carefully checked to determine that
it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of
parts, mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should be properly
repaired or replaced by an authorized service center unless
otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not
use chain saw if switch does not turn it on and off. Do not operate a
chain saw that is damaged, improperly adjusted, or is not
completely and securely assembled. Be sure that the saw chain
stops moving when the trigger is released.
(2.) Do not over reach.
(3.) Keep proper footing and balance at all times.
(4.) Don't let the nose of the guide bar contact a log, branch, ground
or other obstruction.
(5.) Don't cut above shoulder height.
(6.) Use devices such as low kickback chain and reduced kickback
guide bars that reduce the risks associated with kickback.
(7.) Only use replacement bars and chains specified by the
manufacturer or the equivalent.
(8.) Never let the moving chain contact any object at the tip of the
guide bar.
(9.) Keep the working area free from obstructions such as other
trees, branches, rocks, fences, stumps, etc. Eliminate or avoid any
obstruction that your saw chain could hit while you are cutting
through a particular log or branch.
(10.) Keep your saw chain sharp and properly tensioned. A loose or
dull chain can increase the chance of kickback. Check tension at
regular intervals with the motor stopped and battery removed, never
with the motor running.
(11.) Begin and continue cutting only with the chain moving at full
speed. If the chain is moving at a slower speed, there is a greater
chance for kickback to occur.
• Guard Against Kickback
(12.) Cut one log at a time.
WARNING: KICKBACK may occur when the nose or tip
of the guide bar touches an object, or when the wood closes
in and pinches the saw chain in the cut. Tip contact in some
cases may cause a lightning fast reverse reaction, kicking the
guide bar up and back towards the operator. Pinching the saw
chain along the top of the guide bar may push the guide bar
rapidly back towards the operator. Either of these reactions
may cause you to lose control of the saw which could result in
serious injury to user.
(13.) Use extreme caution when re-entering a previous cut. Engage
ribbed bumpers into wood and allow chain to reach full speed
before proceeding with cut.
(14.) Do not attempt plunge cuts or bore cuts.
(15.) Watch for shifting logs or other forces that could close a cut
and pinch or fall into chain.
• Power Supply - Connect chain saw battery charger to correct
voltage, that is, be sure that the voltage supplied is the same as that
specified on the nameplate of the tool.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Use extreme caution when cutting small size brush and
saplings because slender material may catch the saw chain and
be whipped toward you or pull you off balance.
Kickback Safety Features
WARNING: The following features are included on your saw
to help reduce the hazard of kickback; however such features
will not totally eliminate this dangerous reaction. As a chain saw
user do not rely only on safety devices. You must follow all safety
precautions, instructions, and maintenance in this manual to help
avoid kickback and other forces which can result in serious injury.
• Reduced-Kickback Guide Bar, designed with a small radius tip
which reduces the size of the kickback danger zone on bar tip. A
reduced - kickback guide bar is one which has been demonstrated
to significantly reduce the number and seriousness of kickbacks
when tested in accordance with safety requirements for electric
chain saws.
WARNING: Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains chemicals
known to the State of California to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry
products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
• Low-Kickback Chain, designed with a contoured depth gauge and
guard link which deflect kickback force and allow wood to gradually
ride into the cutter. A low-kickback chain is a chain which has met
kickback performance requirements of ANSI B175.1-1991.
• Do not operate chain saw while in a tree, on a ladder, on a
scaffold, or from any unstable surface.
• Avoid prolonged contact with dust from power sanding,
sawing, grinding, drilling, and other construction activities.
Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth, eyes, or lay on the
skin may promote absorption of harmful chemicals.
• Hold tool by insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring.
Contact with a "live" wire will make exposed metal parts of the tool
"live" and shock the operator.
WARNING: Use of this tool can generate and/or disburse
dust, which may cause serious and permanent respiratory or
other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away
from face and body.
• Do not attempt operations beyond your capacity or
experience. Read thoroughly and understand completely all
instructions in this manual.
• Before you start chain saw, make sure saw chain is not
contacting any object.
SAVE THESE INSTRUCTIONS
SYMBOLS
• Do not operate a chain saw with one hand! Serious injury to
the operator, helpers, or bystanders may result from one
handed operation. Achain saw is intended for two-handed use only.
• Keep the handles dry, clean, and free of oil or grease.
• Do not allow dirt, debris, or sawdust to build up on the motor
or outside air vents.
The label on your tool may include the following symbols.
V................volts
Hz..............hertz
min ............minutes
A ....................amperes
W ..................watts
..................alternating current
n
..........direct current
o ..................no load speed
Class II Construction
..............
....................earthing terminal
• Stop the chain saw before setting it down.
• Do not cut vines and/or small under brush.
............safety alert symbol
.../min ............revolutions per
minute
5
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGERS
Before using your Chain Saw familiarize yourself with all operating
and safety features.
16
SAVE THESE INSTRUCTIONS: This manual contains important
safety instructions for battery chargers.
4
• Before using charger, read all instructions and cautionary markings
15
14
2
5
on charger, battery pack, and product using battery pack.
3
WARNING: Shock hazard. Do not allow any liquid to get
inside charger.
12
1
CAUTION: Burn hazard. To reduce the risk of injury, charge
only designated Black & Decker batteries. Other types of batteries
may burst causing personal injury and damage.
13
11
10
CAUTION: Under certain conditions, with the charger plugged
in to the power supply, the charger can be shorted by foreign
material. Foreign materials of a conductive nature such as, but not
limited to, steel wool, aluminum foil, or any buildup of metallic
particles should be kept away from charger cavities. Always unplug
the charger from the power supply when there is no battery pack in
the cavity. Unplug charger before attempting to clean.
6
8
7
9
1. Trigger Switch
2. Lock Off Button
3. Oil Reservoir
4. Oil Reservoir Cap
5. Front Hand Guard
6. Battery
9. Saw Chain
• The charger supplied with this product is intended to be
plugged in such that it is correctly orientated in a vertical or
floor mount position.
10. Sprocket Cover
11. Allen Head Screws
12. Guide Bar Scabbard
13. Wrench
• DO NOT attempt to charge the battery pack with any chargers
other than the ones in this manual. The charger and battery
pack are specifically designed to work together.
14. Charger
15. Rear Handle
7. Ribbed Bumper
8. Guide Bar
• These chargers are not intended for any uses other than
charging designated Black & Decker rechargeable batteries.
Any other uses may result in risk of fire, electric shock or electrocution.
• Do not expose charger to rain or snow.
16. Front Handle
• Pull by plug rather than cord when disconnecting charger.
This will reduce risk of damage to electric plug and cord.
• Make sure that cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or stress.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
center when service or repair is required. Incorrect reassembly
may result in a risk of electric shock, electrocution or fire.
• Disconnect the charger from the outlet before attempting any
cleaning. This will reduce the risk of electric shock. Removing the
battery pack will not reduce this risk.
• Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in risk of
fire, electric shock, or electrocution.
• An extension cord must have adequate wire size (AWG or
American Wire Gauge) for safety. The smaller the gauge number
of the wire, the greater the capacity of the cable, that is 16 gauge
has more capacity than 18 gauge. When using more than one
extension to make up the total length, be sure each individual
extension contains at least the minimum wire size.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard household
electrical power (120 Volts). Do not attempt to use it on any
other voltage.
Recommended Minimum Wire Size for Extension Cords
SAVE THESE INSTRUCTIONS
Minimum Gauge for Cord Sets
Volts
120V
240V
Total Length of Cord in Feet
IMPORTANT SAFETY WARNINGS
0-25
26-50
51-100 101-150
FOR BATTERY PACKS
0-50
51-100 101-200 201-300
American Wire Gauge
Ampere Rating
More Not more
Than Than
WARNING: For safe operation, read this manual and manuals
originally supplied with tool before using the charger.
0
-
-
-
-
6
18
18
16
14
16
16
16
12
16
14
14
14
12
12
The battery pack is not fully charged out of the carton. Before using
the battery pack and charger, read the safety instructions below.
Then follow charging procedures outlined.
6
10
12
16
10
12
Not Recommended
READ ALL INSTRUCTIONS
• Do not place any object on top of charger or place the charger
on a soft surface that might block the ventilation slots and
result in excessive internal heat. Place the charger in a
position away from any heat source. The charger is ventilated
through slots in the top and the bottom of the housing.
• Do not mount charger on wall or permanently affix charger to
any surface. The charger is intended to use on a flat, stable
surface (i.e., table top, bench top).
• Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
battery packs are burned.
• Do not charge or use battery in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust. Inserting
or removing the battery from the charger may ignite the dust or fumes.
• If battery contents come into contact with the skin, immediately
wash area with mild soap and water. If battery liquid gets into the
eye, rinse water over the open eye for 15 minutes or until irritation
ceases. If medical attention is needed, the battery electrolyte for Li-
ion batteries is composed of a mixture of liquid organic carbonates
and lithium salts.
• Do not operate charger with damaged cord or plug — have
them replaced immediately.
• Do not operate charger if it has received a sharp blow, been
dropped, or otherwise damaged in any way. Take it to an
authorized service center.
• Do not disassemble charger; take it to an authorized service
7
Download from Www.Somanuals.com. All Manuals Search And Download.
• Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persist, seek medical attention.
CHARGING PROCEDURE
The standard charger provided will charge a fully depeleted battery
WARNING: Burn hazard. Battery liquid may be flammable if
in about 8 hours.
exposed to spark or flame.
1. Plug the charger into an appropriate outlet before inserting the
battery pack.
• Charge the battery packs only in Black & Decker chargers.
• DO NOT splash or immerse in water or other liquids. This may
cause premature cell failure.
2. Insert the battery pack into the
A
charger as shown in figure A.
• Do not store or use the tool and battery pack in locations where
the temperature may reach or exceed 105°F (40˚C) (such as
outside sheds or metal buildings in summer).
3. The green LED will flash
indicating that the battery is
being charged.
4. The completion of charge
WARNING: Never attempt to open the battery pack for any
reason. If battery pack case is cracked or damaged, do not insert into
charger. Do not crush, drop or damage battery pack. Do not use a
battery pack or charger that has received a sharp blow, been
dropped, run over or damaged in any way (i.e., pierced with a nail, hit
with a hammer, stepped on). Damaged battery packs should be
returned to service center for recycling.
is indicated by the green
LED remaining on
continuously. The pack is
fully charged and may be
used at this time or left on
the charger.
Recharge discharged batteries as soon as possible after use or
battery life may be greatly diminished. It is recommended that the
batteries be recharged after each use.
WARNING: Fire hazard. Do not store or carry battery so that
metal objects can contact exposed battery terminals. For
example, do not place battery in aprons, pockets, tool boxes, product
kit boxes, drawers, etc., with loose nails, screws, keys, etc.
CHARGER DIAGNOSTICS
Transporting batteries can possibly cause fires if the battery
terminals inadvertently come in contact with conductive materials
such as keys, coins, hand tools and the like. The US Department
of Transportation Hazardous Material Regulations (HMR) actually
prohibit transporting batteries in commerce or on airplanes (i.e.,
packed in suitcases and carry-on luggage) UNLESS they are properly
protected from short circuits. So when transporting individual batteries,
make sure that the battery terminals are protected and well insulated
from materials that could contact them and cause a short circuit.
NOTE: LI-ION batteries should not be put in checked baggage.
This charger is designed to detect certain problems that can arise
with the battery packs or the power source. Problems are indicated
by one LED flashing in different patterns.
BAD BATTERY
The charger can detect a weak or damaged battery. The red
LED flashes in the pattern indicated on the label. If you see
this bad battery blink pattern, do not continue to charge the
battery. Return it to a service center or a collection site for
recycling.
STORAGE RECOMMENDATIONS
HOT/COLD PACK DELAY
1. The best storage place is one that is cool and dry away from
direct sunlight and excess heat or cold.
When the charger detects a battery that is excessively hot or
excessively cold, it automatically starts a Hot/Cold Pack
2. Long storage will not harm the battery pack or charger.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Delay, suspending charging until the battery has normalized. After
this happens, the charger automatically switches to the Pack
Charging mode. This feature ensures maximum battery life. The red
LED flashes in the pattern indicated on the label when the hot / cold
pack delay is detected.
LEAVING THE BATTERY IN THE CHARGER
The charger and battery pack can be left connected with the green
LED glowing indefinitely. The charger will keep the battery pack
fresh and fully charged.
5. Foreign materials of a conductive nature such as, but not limited
to, steel wool, aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery pack in the
cavity. Unplug charger before attempting to clean.
6. Do not freeze or immerse charger in water or any other liquid.
WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Never attempt to open the battery pack for any
reason. If the plastic housing of the battery pack breaks or cracks,
return to a service center for recycling.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the battery
pack is charged when the air temperature is between 60°F and
80°F (16°- 27°C). DO NOT charge the battery pack in an air
temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).
This is important and will prevent serious damage to the battery
pack.
INSTALLING / REMOVING BATTERY PACK
WARNING: Make certain
the lock-off button is engaged to
B/C
prevent switch actuation before
removing or installing battery.
2. The charger and battery pack may become warm to touch while
charging. This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the battery pack after use, avoid
placing the charger or battery pack in a warm environment such as
in a metal shed, or an uninsulated trailer.
TO INSTALL BATTERY PACK:
Insert battery pack into tool until
an audible click is heard
(figure B/C).
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or other
appliance
TO REMOVE BATTERY PACK:
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
c. Move charger and battery pack to a location where the
surrounding air temperature is approximately 60°F and 80°F
(16°- 27°C)
Depress the battery release
button in the back of the battery pack and pull battery pack out of
tool (figure B/C).
d. If charging problems persist, take the tool, battery pack and
charger to your local service center.
4. The battery pack should be recharged when it fails to produce
sufficient power on jobs which were easily done previously. DO
NOT CONTINUE to use under these conditions. Follow the
charging procedure. You may also charge a partially used pack
whenever you desire with no adverse affect on the battery pack.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
• Wearing protective gloves, grasp the saw chain (9) and guide bar
(8) with one hand and pull the guide bar scabbard (12) off with your
free hand.
PREPARING YOUR CHAIN SAW FOR USE
WARNING: Read and understand all instructions. Failure to
follow all instructions listed below may result in electric shock, fire
and/or serious personal injury.
• Place the saw chain and guide bar assembly around the sprocket
(19). Check to make sure that the slot (20) in the guide bar (8) is
over the two location pins (21)
F
shown in figure E and that the hole
below the slot is located over the
adjustment pin (22).
ASSEMBLY
Installing the Guide Bar and Saw Chain
CAUTION: Sharp chain. Always wear protective gloves when
handling the chain. The chain is sharp and can cut you when it is not
running.
23
• Replace sprocket cover (10) and
thread allen head screws (11) in
with wrench until snug, then back
wrench off one full turn.
13
WARNING: Sharp moving chain. To prevent accidental
operation, insure that battery is disconnected from the tool
before performing the following operations. Failure to do this
could result in serious personal
• Cut the plastic wire tie holding the
saw chain to the guide bar. Be sure
to cut away from yourself to prevent injury if cutting instrument
should slip.
D
injury.
• Pull bar nose up and keep it up as you adjust tension.
• With the flat screwdriver end of the wrench provided rotate the
tension adjustment screw (23) in the front of the housing clockwise
to increase the chain tension as in figure F.
The saw chain and guide bar are
packed separately in the carton
inside the scabbard. The chain has
been placed on the guide bar at the
factory to insure that the teeth are
facing in the proper direction when
you first attach it. Should the chain
come off of the guide bar, refer to the
11
10
• Follow instructions in “Adjusting Chain Tension” section.
• While still holding the bar nose up, tighten the rear allen screw first,
then tighten the front allen screw. Make sure both allen screws are
securely tightened. Do not overtighten.
13
• When the chain is new check the tension frequently (after
disconnecting battery) during the first 2 hours of use as a new chain
stretches slightly.
section “Replacing the Chain” for proper tooth orientation.
• Place the saw on a firm surface.
E
Rotate the two allen head screws
(11) counterclockwise with the
wrench (13) provided as shown in
figure D.
Replacing the Saw Chain
20
22
CAUTION: Sharp chain. Always wear protective gloves when
handling the chain. The chain is sharp and can cut you when it is not
running.
• Remove sprocket cover (10) and
19
allen head screws (11).
21
WARNING: Sharp moving chain. To prevent accidental
operation, insure that battery is disconnected from the tool
before performing the following operations. Failure to do this could
result in serious personal injury.
21
• Cut the plastic wire tie holding the
guide bar scabbard (12) to the
guide bar (8). Be sure to cut away
from yourself to prevent injury if cutting instrument should slip.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
• Place the saw on a firm surface. Rotate the two allen head screws
(11) counterclockwise with the wrench (13) provided as shown in
figure D.
Adjusting Chain Tension
CAUTION: Sharp chain. Always wear protective gloves when
handling the chain. The chain is sharp and can cut you when it is
not running.
• To remove the saw chain (9), rotate the tension adjustment screw
(23) in the front of the housing using the flat screwdriver end of the
wrench (13) as shown in figure F. Turning the screw
counterclockwise allows the guide bar to recede and reduces the
tension on the chain so that it may be removed.
WARNING: Sharp moving chain. To prevent accidental
operation, insure that battery is disconnected from the tool
before performing the following operations. Failure to do this
could result in serious personal injury.
• Remove sprocket cover (10) and
• With the saw still on a firm surface check the chain tension. The
tension is correct when the chain
G
allen head screws (11).
H
• Lift the worn saw chain (9) out of
the groove in the guide bar (8).
• Place new chain in groove of guide
bar making sure saw teeth are
facing correct direction by
matching arrow on chain with
graphic on housing shown in
figure G.
snaps back after being pulled 1/8
inch (3mm) away from the guide
bar (8) with light force from the
middle finger and thumb as
1/8 in.
shown in figure H. There should
be no “sag” between the guide
bar and the chain on the
(3mm)
underside as shown in figure I.
• To adjust saw chain tension,
loosen the allen head screws
(11).
• Place the saw chain and guide bar assembly
around the sprocket (19). Check to make sure
that the slot (20) in the guide bar (8) is over the
two location pins (21) shown in figure E and
that the hole below the slot is located over the
adjustment pin (22).
G1
I
• Rotate the tension adjustment
screw (23) in the front of the
housing using the flat
• Replace sprocket cover (10) and thread allen
head screws (11) in with wrench until snug,
then back wrench off one full turn.
screwdriver end of the wrench
(13) as shown in figure F.
• Do not over-tension the chain as
this will lead to excessive wear
• Pull bar nose up and keep it up as you adjust
tension Figure G1.
and will reduce the life of the bar and chain. Overtensioning also
reduces the amount of cuts you will get per battery charge.
• Once chain tension is correct, tighten allen head screws (11).
• When the chain is new check the tension frequently (after
disconnecting battery) during the first 2 hours of use as a new chain
stretches slightly.
• Rotate the tension adjustment screw (23) in the front of the housing
clockwise to increase the chain tension as in Figure F.
• Follow instructions in “Adjusting Chain Tension” section.
• While still holding the bar nose up, securely tighten the rear allen
screw (11) first, then tighten the front allen screw.
• When the chain is new check the tension frequently (after
disconnecting battery) during the first 2 hours of use as a new chain
stretches slightly.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chain Oiling
OPERATING THE CHAIN SAW
NOTES:
- A high quality bar and chain oil or SAE30 weight motor oil should be
used for chain and bar lubrication. Never use waste oil or very thick
oil. These may damage your chain saw.
WARNING: Read and understand all instructions. Failure to
follow all instructions listed below may result in electric shock, fire
and/or serious personal injury.
- Replace oil reservoir cap immediately after filling oil reservoir.
Failure to do so will allow excessive oil to drip out of oiling outlet.
- It is normal for a small amount of excess oil to drip from the chain
saw bar and chain during storage. Do not store chain saw on top of
any thing that may be damaged by the dripping oil.
• Remove the oil reservoir cap (4) and fill the oil reservoir (3) with the
above recommended oil. For
• Guard Against Kickback which can result in severe injury or
death. See Important Safety Instructions “Guard Against
Kickback”, to avoid the risk of kickback.
• Do not overreach. Do not cut above chest height. Make sure
your footing is firm. Keep feet apart. Divide your weight evenly on
both feet.
• Use a firm grip with your left hand on the front handle (16) and
your right hand on the rear handle (15) so that your body is to the
left of the guide bar.
best results, keep reservoir over
half full.
J
• Lubricate the saw chain as shown
in figure J by pressing the bulb
on the oil reservoir cap (4) twice
before making each cut. Hold
bulb down for 3-4 seconds.
• Because the saw uses a gravity
fed oiling system, the saw should
be pointed downward and slightly
to the right when applying oil to the
chain.
• Do not hold chain saw by front hand guard (5). Keep elbow of left
arm locked so that left arm is straight to withstand a kickback.
WARNING: Never use a cross-handed grip (left hand on the
rear handle and right hand on the front handle).
WARNING: Never allow any part of your body to be in line
with the guide bar (8) when operating the chain saw.
• Never operate while in a tree, in any awkward position or on a
ladder or other unstable surface. You may lose control of saw
causing severe injury.
K
L
• Keep the chain saw running at full speed the entire time you
are cutting.
Transporting Saw
• Always remove the battery (6)
from the tool (figure K) and cover
the guide bar (8) with the
scabbard (12) (figure L) when
transporting the saw. See the
warning under “Battery Cap
Information” for additional
information on transporting the
battery.
• Allow the chain to cut for you. Exert only light pressure. Do not
put pressure on chain saw at end of cut.
M
Connecting the Battery
• Place the battery (6) into the tool as
shown in figure M and be certain that it
is inserted fully into the tool cavity until it
“clicks” into place. To remove the
battery from the tool, press down on the
release button (18) on the back of the
battery and slide out.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
any utility line, the utility company should be notified immediately.
Scrutinize the surrounding overhead for dead or broken limbs or
branches which may fall during the felling process.
The chain saw operator should keep on the uphill side of the
terrain as the tree is likely to
Switch
N
• Always be sure of your footing
and grip the chain saw firmly
with both hands with the thumb
and fingers encircling both
handles.
2
1
roll or slide downhill after it is
RETREAT
O
felled.
• To turn the tool ON push the lock
off button (2) to either side and
squeeze the trigger switch (1)
with your fingers as shown in
• (Figure O) A retreat path
should be planned and
cleared as necessary before
cuts are started. The retreat
path should extend back and
diagonally to the rear of the
expected line of fall.
DIRECTION
OF
FALL
figure N. (Once the tool is running you can release the lock off
button.)
TREE
45°
• To turn the tool OFF, release the trigger switch.
Chain Braking System
• Before felling is started,
consider the natural lean of
Your chain saw is equipped with a motor chain braking system which
will stop the chain quickly each time you release the trigger. This
system should be tested before every use.
the tree, the location of larger branches and the winddirection to
judge which
way the tree will fall. Have wedges (wood, plastic or aluminum)
and a heavy mallet handy.
Saw Chain Sharpness
The cutters will dull immediately if they touch the ground or a nail
while cutting. Refer to “Sharpening the Chain”.
Remove dirt, stones, loose bark, nails, staples, and wire from the
tree where the felling
P
cuts are to be made.
• (Figure P) Notching
Undercut - Make the
notch 1/3 of the
Saw Chain Tension
2 (5cm)
This should be done regularly. Refer to “Adjusting Chain Tension”.
DIRECTION
OF FALL
INCHES
FELLING BACK
CUT
Common Cutting Techniques
diameter of the tree,
perpendicular to the
direction of the fall.
Make the lower
Felling
2 (5cm)
Felling is the process of cutting down a tree. Be sure battery is
fully charged before felling a tree so you can finish on a single
charge. Do not fell trees in high wind conditions.
INCHES
NOTCH
horizontal notching cut
first. This will help to
Bucking is the process of cutting a felled tree or log into lengths.
When bucking and felling operations are being performed by two
or more persons, at the same time, the felling operation should be
separated from the bucking operation by a distance of at least
twice the height of the tree being felled. Trees should not be felled
in a manner that would endanger any person, strike any utility line
or cause any property damage. If the tree does make contact with
HINGE
avoid pinching of either the saw chain or the guide bar when the
second notch is being made.
• (Figure Q) Felling Back Cut - Make the felling back cut at least
2 inches (51mm) higher than the horizontal notching cut. Keep the
felling back cut parallel to the horizontal notching cut. Make the
13
Download from Www.Somanuals.com. All Manuals Search And Download.
felling back cut so enough wood is left to act as a hinge. The hinge
wood keeps the tree from twisting and falling in the wrong
direction. Do not cut
Bucking
Bucking is cutting a felled tree or log into lengths. How you should
cut depends on how the log is supported. Use a saw horse
(figure W) whenever possible.
Q
through the hinge.
• (Figure Q) As the
felling cut gets close to
the hinge the tree
2 (5cm)
Always start a cut with the chain running at full speed and the
ribbed bumper (7) in contact with the wood. To complete the cut
use a pivoting action of the ribbed bumper against the wood.
DIRECTION
OF FALL
INCHES
FELLING BACK
CUT
should begin to fall. If
there is any chance that
the tree may not fall in
the desired direction or
it may rock back and
bind the saw chain,
• (Figure S) When
supported along its
whole length
CUT FROM TOP
(OVERBUCK)
AVOID CUTTING
EARTH
2 (5cm)
S
INCHES
NOTCH
Make a cut from the
top (overbuck), but
avoid cutting the earth
as this will dull your
saw quickly.
HINGE
stop cutting before the
felling cut is complete
and use wedges to open the cut and drop the tree along the
desired line of fall. When the tree begins to fall remove the chain
saw from the cut, stop the motor, put the chain saw down, then
use the retreat path planned. Be alert for overhead limbs falling
and watch your footing.
• (Figure T) When
supported at
Limbing (figure R)
T
2nd CUT
R
one end
Limbing is removing the
OVERBUCK (2/3
DIAMETER) TO
MEET 1st CUT (TO
AVOID PINCHING)
First, cut 1/3 the
diameter from the
underside
LIMB CUT
branches from a fallen
tree. When limbing, leave
larger lower limbs to
2
1
(underbuck).
support the log off the
ground. Remove the
small limbs in one cut.
Branches under tension
should be cut from the
bottom up to avoid binding
the chain saw. Trim limbs
from opposite side
Then make the
finished cut by
overbucking to
meet the first cut.
1st CUT UNDERBUCK (1/3
DIAMETER) TO AVOID
SPLINTERING
KEEP WORK OFF GROUND. LEAVE
SUPPORT LIMBS UNTIL LOG IS CUT
keeping tree stem between you and saw. Never make cuts with saw
between your legs or straddle the limb to be cut.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
• (Figure U) When supported at both ends
CARE AND MAINTENANCE
First, cut 1/3 down from the top overbuck. Then make the finished
cut by underbucking the lower 2/3 to meet the first cut.
Use only mild soap and damp cloth to clean the tool. Do not use
solvents to clean the plastic housing of the saw. Never let any liquid
get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by authorized
service centers or other qualified service organizations, always using
identical replacement parts.
1st CUT OVERBUCK (1/3
U
DIAMETER) TO AVOID
1
SPLINTERING
2
2nd CUT UNDERBUCK (2/3
DIAMETER) TO MEET 1st CUT
(TO AVOID PINCHING)
Regular maintenance ensures a long effective life for your chain
saw. We recommend you make the following checks on a regular
basis:
• (Figure V) When on a slope
Always stand on the uphill side of
the log. When "cutting through", to
maintain complete control release
the cutting pressure near the end
of the cut without relaxing your
grip on the chain saw handles.
Don't let the chain contact the
ground. After completing the cut,
wait for the saw chain to stop
before you move the chain saw.
Oil Level
STAND ON
UPHILL
SIDE
V
The level in the reservoir should not be allowed to fall below a
quarter full.
Chain and Bar
WHEN
After every few hours of use, remove the guide bar and chain and
clean thoroughly.
CUTTING
BECAUSE
LOG MAY
ROLL
Saw Chain Sharpening
CAUTION: Sharp chain. Always wear protective gloves when
handling the chain. The chain is sharp and can cut you when it is not
running.
Always stop the motor before moving from tree to tree.
• (Figure W) When using a saw
WARNING: Sharp moving chain. To prevent accidental
operation, insure that battery is disconnected from the tool
before performing the following operations. Failure to do this
could result in serious personal injury.
W
horse
This is strongly recommended
whenever possible. Position the
log in a stable position. Always cut
on the outside of the saw horse
arms.
To get the best possible performance from your chain saw it is
important to keep the teeth of the chain sharp. Follow these helpful
tips for proper saw chain sharpening:
1. For best results use a 4.5mm file and a file holder or filing guide to
sharpen your chain. This will ensure you always get the correct
sharpening angles.
2. Place the file holder flat on the top plate and depth gauge of the
cutter.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3. (Figure X) Keep the correct top
plate (24) filing angle line of 30°
on your file guide parallel with
your chain (file at 60° from
THE RBRC™ SEAL
24
The RBRC™ (Rechargeable Battery Recycling
Corporation) Seal on the LI-ION battery (or battery pack)
indicates that the costs to recycle the battery (or battery
pack) at the end of its useful life have already been paid
by Black & Decker.
X
chain viewed from above).
60°
RBRC™ in cooperation with Black & Decker and other battery
users, has established programs in the United States to facilitate the
4. (Figure Y) Sharpen cutters (25)
on one side of the chain first. File from the inside of each cutter to collection of spent LI-ION batteries. Help protect our environment and
the outside. Then turn your saw around and repeat the processes conserve natural resources by returning the spent LI-ION battery to
(2,3,4) for cutters on the other side of the chain. Use a flat file to
file the tops of the
an authorized Black & Decker service center or to your local retailer
for recycling. You may also contact your local recycling center for
information on where to drop off the spent battery. RBRC™ is a
registered trademark of the Rechargeable Battery Recycling Corporation.
rakers (portion of chain link in
front of the cutter) so that they
are about .025 inch (.635 mm)
below the tips of the cutters.
Y
.025 in.
"
.635mm
25
ACCESSORIES
5. (Figure Z) Keep all cutter
lengths equal.
Accessories are available from your local retailer or nearest
6. If damage is present on the
chrome surface of the top
plates or side plates, file back
until such damage is
Black & Decker service center.
Z
Replacement chain accessory number RC800
(servicepart#623382-00)
Replacement bar service part # 623381-00
WARNING: The use of accessories not recommended in this
manual may be hazardous.
removed.
SERVICE INFORMATION
CAUTION: After filing, the cutter will be sharp, use extra caution
during this process.
All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool
service. Whether you need technical advice, repair, or genuine
factory replacement parts, contact the Black & Decker location
nearest you. To find your local service location, refer to the yellow
page directory under "Tools—Electric" or call: 1-800-544-6986 or
NOTE: Each time the chain is sharpened, it loses some of the low
kickback qualities and extra caution should be used. It is
recommended that a chain be sharpened no more than four times.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
FULL TWO-YEAR HOME USE WARRANTY
If your Chain Saw does not operate correctly check the following:
Problem
Possible Cause
Possible Solution
Black & Decker (U.S.) Inc. warrants this product for two years against
any defects in material or workmanship. The defective product will be
replaced or repaired at no charge in either of two ways.
• Tool will not
• Battery not
installed properly.
• Battery not
charged.
• Check battery installation.
start.
The first, is to return the product to the retailer from whom it was
purchased (provided that the store is a participating retailer). Returns
should be made within the time period of the retailerʼs policy for
exchanges (usually 30 to 90 days after the sale). Proof of purchase
may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for
exchanges.
• Check battery charging
requirements.
• Lock-out button not
• Push lock off
actuated.
button/actuate trigger.
• Insert battery into charger
until green LED appears.
Charge up to 8 hours if
battery totally drained.
• Battery not
inserted into
charger.
• Unit will not
charge.
The second option is to take or send the product (prepaid) to a Black
& Decker owned or authorized Service Center for repair or
replacement at our option. Proof of purchase may be required.Black
& Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you
specific legal rights and you may have other rights which vary from
state to state or province to province. Should you have any
questions, contact the manager of your nearest Black & Decker
Service Center. This product is not intended for commercial use.
LATIN AMERICA: This warranty does not apply to products sold in
Latin America. For products sold in Latin America, check country
specific warranty information contained in the packaging, call the local
company or see the website for warranty information.FREE
WARNING LABEL REPLACEMENT: If your warning labels become
illegible or are missing, call 1-800-544-6986 for a free replacement.
• Refer to “adjusting chain
• Chain too tight.
• Bar / chain
overheated.
tension” section.
• Refer to “chain oiling”
section.
• Lubrication
needed.
• Chain is loose. • Chain tension set • Refer to “adjusting chain
incorrectly.
tension” section.
• Chain tension set • Refer to “adjusting chain
• Poor cut
quality.
incorrectly.
• Chain needs
replacement.
tension” section.
Note: Excessive tension
leads to excessive wear
and reduction in life of bar
& chain. Lubricate before
each cut.
Refer to “replacing the
chain” section.
Imported by
See ʻTools-Electricʼ
– Yellow Pages –
for Service & Sales
• Unit runs but
does not cut.
• Chain installed
backwards.
• Refer to sections for
installing and removing
chain.
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
• Oil is not
getting to
chain.
• Sawdust / debris is • Remove battery, remove
accumulated under sprocket cover. Clean out
accumulatedsawdust/debris.
sprocket cover.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
|