Broadband Products Network Router Networked Boat User Manual |
Xtreme Powered Networked Boat
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Confirm you have the following equipment included with your bridge:
1: Power over Ethernet kit consisting of the following:
Wall power plug
Inverter
Power over Ethernet adapter
2: High power Bridge/Router
Xtreme power bridge/router
4: Two (2) Ethernet CAT-5 cables
Download from Www.Somanuals.com. All Manuals Search And Download.
1: Attach the bracket to the rear screws of the bridge/router below:
(rear of Xtreme power bridge)
2: Attach the bracket to the vertical surface of your boat in a convenient location. This
device has a NEMA enclosure so it can withstand some water exposure.
3: Connect the brackets together with the attached screws. The bridge/router should be
installed so that the antenna and Ethernet connectors point down.
Download from Www.Somanuals.com. All Manuals Search And Download.
(mounting bracket from vertical surface to the bridge router)
2: Attaching the antenna cable to the bridge/router
The connector on the bridge/router is an N male type. We have included an adapter that
connects to the bridge and will accept our standard SMA cable. Connect this adapter to the
bridge/router as shown below:
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach SMA adapter from the long range antenna cable to the adapter on the bridge/router
unit via the antenna connector on the rear of the unit. Hand tighten only. Attach the coaxial
seal around all RF connectors and then seal with silicone or a superior grade of electrical
tape.
3: Attaching the Ethernet Cable to the Bridge
Feed one end of the ethernet cable through each of the plastic and rubber grommets. Each
grommet fits inside the next and should be closed completely as seen in the image below
a) Plug Ethernet cables into the PoE adapter. Your Crossover cable (the cable with
mismatched heads) should connect your computer to the PoE adapter, and the
Straighthrough cable (the cable with matching heads) should connect the PoE adapter to
the bridge.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: make sure you are using the correct cable between the PoE adapter and your
bridge hardware. USING THE CROSSOVER INSTEAD OF THE PASSTHROUGH WILL DAMAGE
YOUR BRIDGE.
b) Assemble the power adapter and connect it to your PoE adapter.
The lights on the front of the unit should blink and after a few moments the Power
and LAN lights should go solid.
Your bridge came Pre-configured it should automatically connect to BBX for you, simply open your
web-browser and after a short delay you should be redirected to the BBX login screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
1: Open up your browser. Type the following ip address into the address bar: 192.168.2.254
2: You will be prompted to enter the username and password assigned to your bridge. The default
address username and password is as follows:
Username: admin
Password: admin
(security page prompt to access the bridge/router)
Once the correct username and password have been entered you will be taken to the setup
wizard. Follow the progression of screens below to set the unit up via the wizard. If you want the
unit to connect to BBX, simply match the information on your screen to the information shown
below.
After entering the username and password you will get the setup wizard. For all customers of
BroadbandXpress,we have preconfigured the units for your easy use. For all others follow the steps
below:
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 1: select next
Begin by clicking “Next” on the initial wizard explanation screen.
STEP 2:
select Wireless ISP
select next
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: If you select the “Bridge” option you will be unable to access these configuration
screens again without hard-resetting the unit (via the button on the back).
STEP 3: select next:
STEP 4: select next
The LAN interface screen allows you to select the configuration IP assigned to your bridge. This
info should NOT be changed.
STEP 5:
WAN ACCESS TYPE: select DHCP Client
Select next
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6:
TO SELECT A NETWORK TO CONNECT WITH AS A DEFAULT
Band: select 2.4 GHz(B+G)
Mode: select Client
Network Type: select infrastructure
SSID: Select your desired network(we have set your network as bbx). It can be changed here or
under scan mode below:
IMPORTANT: SSIDs are case-sensitive and must be entered EXACTLY as they are transmitted.
STEP 7:
select none
Download from Www.Somanuals.com. All Manuals Search And Download.
Select finished
The Wireless Security Page allows you to enter the appropriate pre-connection encryption key for
the network you wish to join. Most commercial wireless networks do not use encryption.
YOUR BRIDGE IS NOW SET TO CONNECT TO THE BBX NETWORK OR ANY
OTHER NETWORK OF YOUR CHOICE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1: Open up your browser. Type 192.168.2.254 in your browser to access the web interface of
the bridge
Step 2:Click on the labeled Wireless on the left sidebar.
Step 3: Select Site Survey on the left sidebar
Step 4: select refresh
Step 5: you will now be able to view all the available networks:
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 6: hit select on the desired network and scroll to the bottom and hit connect:
Step 7: You will get notice that you have successfully connected to the network of choice.
Step 8: Logout from the bridge
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 - INSTALLING A WIRELESS ROUTER WITH THE NETWORKED BOAT
Any standard wireless router should work with the bridge router. We standardize using the Linksys
products due to their universal availability. BroadbandXpress typically will ship a router with your
bridge to provide a complete package. In the event that your router was not preconfigured by BBX
ensure that wireless security is enabled.
Critical Warning:
It is paramount to secure your wireless router with wireless encryption. Failure to secure a
router will allow outsiders to access your bridge router and may disrupt your service.
Step 1: Plug the cross over ethernet cable from the Data In jack of the Power over Ethernet
injector to the Internet jack of the router as shown above.
Step 2: Connect to your wireless router via your wireless adapter of choice.
Step 3: Open a browser and you will connect to the selected wireless provider that you have set in
the bridge/router.
Step 4: To access the Bridge/router simply type 192.169.2.254 in your browser.
CONGRATULATIONS, YOUR NETWORKED-BOAT SYSTEM IS NOW
SET UP CORRECT TO WORK WITH THE BBX NETWORK.
Download from Www.Somanuals.com. All Manuals Search And Download.
|