Black Box Switch IC244A R2 User Manual

January 2004  
IC244A-R2  
IC246A-R2  
Single/Dual USB-CAT5 Extender  
165FT  
User Guide  
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX  
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746  
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018  
CUSTOMER  
SUPPORT  
INFORMATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC STATEMENT  
FEDERAL COMMUNICATIONS COMMISSION  
AND  
CANADIAN DEPARTMENT OF COMMUNICATIONS  
RADIO FREQUENCY INTERFERENCE STATEMENT  
Class B Digital Device. This equipment has been tested and found to  
comply with the limits for a Class B computing device pursuant to Part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. However, there is  
no guarantee that interference will not occur in a particular installation. This  
equipment generates, uses, and can radiate radio frequency energy, and, if  
not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. If this equipment does cause  
harmful interference to radio or telephone reception, which can be  
determined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
• Consult an experienced radio/TV technician for help.  
Caution:  
Changes or modifications not expressly approved by the  
party responsible for compliance could void the user’s  
authority to operate the equipment.  
To meet FCC requirements, shielded cables and power cords are required to  
connect this device to a personal computer or other Class B certified device.  
This digital apparatus does not exceed the Class B limits for radio noise  
emission from digital apparatus set out in the Radio Interference Regulation  
of the Canadian Department of Communications.  
Le présent appareil numérique n’émet pas de bruits radioélectriques  
dépassant les limites applicables aux appareils numériques de la classe B  
prescrites dans le Règlement sur le brouillage radioélectrique publié par le  
ministère des Communications du Canada.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
SINGLE/DUAL USB-CAT5 EXTENDER 165FT  
Normas Oficiales Mexicanas (NOM)  
Electrical Safety Statement  
INSTRUCCIONES DE SEGURIDAD  
1. Todas las instrucciones de seguridad y operación deberán ser leídas  
antes de que el aparato eléctrico sea operado.  
2. Las instrucciones de seguridad y operación deberán ser guardadas  
para referencia futura.  
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones  
de operación deben ser respetadas.  
4. Todas las instrucciones de operación y uso deben ser seguidas.  
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,  
cerca de la tina de baño, lavabo, sótano mojado o cerca de una  
alberca, etc.  
6. El aparato eléctrico debe ser usado únicamente con carritos o  
pedestales que sean recomendados por el fabricante.  
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como  
sea recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico  
más allá a lo descrito en las instrucciones de operación. Todo otro  
servicio deberá ser referido a personal de servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su posición no  
interfiera su uso. La colocación del aparato eléctrico sobre una cama,  
sofá, alfombra o superficie similar puede bloquea la ventilación, no se  
debe colocar en libreros o gabinetes que impidan el flujo de aire por  
los orificios de ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de  
calor como radiadores, registros de calor, estufas u otros aparatos  
(incluyendo amplificadores) que producen calor.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOM STATEMENT  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo  
del tipo descrito en el instructivo de operación, o como se indique en  
el aparato.  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la  
polarización del equipo no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que  
no sean pisados ni pellizcados por objetos colocados sobre o contra  
ellos, poniendo particular atención a los contactos y receptáculos  
donde salen del aparato.  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las  
recomendaciones del fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de  
las lineas de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no  
sea usado por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean  
derramados sobre la cubierta u orificios de ventilación.  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del aparato;  
o
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en  
su desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SINGLE/DUAL USB-CAT5 EXTENDER 165FT  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
Contents  
1. Specifications......................................................................................... 6  
2. Introduction............................................................................................ 7  
2.1  
2.2  
Product Contents............................................................................ 7  
About the USB-CAT5 Extender .................................................... 8  
3. Installation............................................................................................ 11  
3.1  
3.2  
3.3  
3.4  
3.5  
3.6  
Before You Begin ........................................................................ 11  
Installing the Local Unit............................................................... 11  
Installing the Remote Unit ........................................................... 11  
Connecting the Local Unit to the Remote Unit............................ 11  
Checking the Installation.............................................................. 12  
Connecting a USB Device ........................................................... 12  
4. Troubleshooting ................................................................................... 13  
4.1  
4.2  
Problems, Causes and Solutions................................................... 13  
Calling Black Box........................................................................ 15  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SINGLE/DUAL USB-CAT5 EXTENDER 165FT  
1.Specifications  
Range (over Category 5  
50 meters (165 ft)  
UTP cable)  
USB device support  
USB-CAT5 Extender IC244A: 1 x full-speed (12  
Mb/s) ) or low-speed (1.5 Mb/s) device.  
USB-CAT5 Extender IC246A: 2 x full-speed (12  
Mb/s) or low-speed (1.5 Mb/s) devices.  
USB hub support  
Up to 3 hubs connected in series.  
Each hub reduces the maximum range by 10  
meters.  
Maximum power  
available to USB at  
Remote Unit  
300 mA when Local Unit is supplied with  
500 mA;  
600 mA when Local Unit is supplied with  
1000 mA  
USB cable  
2 meters (6.6 ft)  
1 x USB Type B  
Local Unit connector  
(upstream)  
Local Unit connector  
(downstream)  
1 x RJ45  
1 x RJ45  
Remote Unit connector  
(upstream)  
Remote Unit connector  
(downstream)  
USB-CAT5 Extender IC244A: 1 x USB Type A  
USB-CAT5 Extender IC246A: 2 x USB Type A  
Local Unit dimensions  
Local Unit weight  
100 mm x 70 mm x 30 mm (4.0” x 2.8” x 1.2”)  
0.1 kg (0.2 lb)  
Remote Unit dimensions 100 mm x 70 mm x 30 mm (4.0” x 2.8” x 1.2”)  
Remote Unit weight  
0.1 kg (0.2 lb)  
0.4 kg (0.8 lb)  
Total system shipping  
weight  
Temperature range  
Regulatory testing  
4°C to 40°C  
FCC, CE Class B  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHAPTER 2: Introduction  
2.Introduction  
This manual is intended to assist IT professionals install the Single/Dual  
USB-CAT5 Extender 165FT. The instructions in this guide assume a general  
knowledge of computer installation procedures, familiarity with cabling  
requirements, and some understanding of USB devices.  
NOTE  
Notes give additional information that could make installation easier.  
2.1 Product Contents  
When you open your product for the first time you should find the following  
items:  
Single/Dual USB-CAT5 Extender 165FT User Guide  
Local Unit  
Remote Unit  
USB cable (2m long)  
To complete the installation, you will also require the following items that  
are not included with the product:  
USB compatible computer  
USB device  
Category 5 Unshielded Twisted Pair (UTP) cable with two RJ45  
connectors (if using surface cabling),  
OR,  
Category 5 UTP cabling with two information outlets and two  
Category 5 UTP patch cords with RJ45 connectors (if using  
premise cabling)  
NOTE  
The maximum length of the Category 5 UTP cable, including patch cords, must not exceed 50 meters.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
SINGLE/DUAL USB-CAT5 EXTENDER 165FT  
2.2 About the USB-CAT5 Extender  
The USB-CAT5 Extender breaks the five-meter distance barrier for the  
connection of USB devices and allows users to enjoy the benefits of USB  
technology beyond the desktop. With the USB-CAT5 Extender, USB  
devices can be located up to 50 meters from the host computer. In addition,  
the USB-CAT5 Extender can supply power to remote low-power and some  
high-power USB devices.  
The product is composed of two individual units, the Local Unit and the  
Remote Unit.  
2.2.1 The Local Unit  
The Local Unit connects to the host computer using a conventional  
USB cable.  
Front View  
Rear View  
4
3
1
2
1 Host Port (USB Type B)  
2 Host LED (green)  
3 Link Port (RJ45)  
4 Link LED (yellow)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHAPTER 2: Introduction  
2.2.2 The Remote Unit  
The Remote Unit connects to the USB device using a conventional  
USB cable. The Remote Unit of the USB-CAT5 Extender IC244A  
enables you to connect one full-speed or low-speed USB device. The  
Remote Unit of the USB-CAT5 Extender IC246A enables you to  
connect two full-speed or low-speed USB devices.  
Front View  
Rear View  
3
2
4
1
1 Device Port  
2 Device LED (green)  
3 Link Port (RJ45)  
4 Link LED (yellow)  
(1 x USB Type A on IC244A)  
(2 x USB Type A on IC246A)  
2.2.3 Network Cabling  
The Local Unit and Remote Unit are interconnected by up to 50  
meters of Category 5 Unshielded Twisted Pair (UTP) cabling. The  
UTP cabling must have a straight-through conductor configuration,  
with no crossovers, and must be terminated with 8-conductor RJ45  
connectors at both ends.  
Remote  
Unit  
Local  
Unit  
Category 5 cable  
USB  
USB  
cable  
cable  
computer  
USB  
device  
NOTE  
Category 5 UTP cabling is the standard data communications cable installed in most commercial and  
some residential buildings.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
SINGLE/DUAL USB-CAT5 EXTENDER 165FT  
2.2.4 USB Cables  
USB cables have two distinct connectors. The Type A connector is used to  
connect the cable from a USB device to the Type A port on a computer or  
hub. The Type B connector is used to attach the USB cable to a USB device.  
USB Type A  
port  
USB Type B  
port  
USB Type B  
connector  
USB Type A  
connector  
2.2.5 Power Handling  
Some USB devices are powered directly from the USB and do not require  
individual power supplies. These devices are called bus-powered devices.  
The USB-CAT5 Extender can provide power to these devices so they can be  
operated remotely.  
Bus-powered devices are further divided into low-power and high-power  
categories. Low-power devices are allowed to draw up to 100 mA from the  
USB. Typical examples include mice, joysticks, and keyboards without  
hubs. High-power devices are allowed to draw up to 500 mA from the USB.  
Typical examples include cameras and keyboards with hubs. To determine if  
a device is high-power or low-power, consult the user documentation for the  
device.  
The USB-CAT5 Extender can supply sufficient power to support all low-  
power devices and most high-power devices. Devices that place a very heavy  
power drain on USB (>300 mA) are not supported. Most USB devices  
operate well within this power budget.  
NOTE  
Devices with their own power source are usually considered to be low-power devices from a USB  
perspective and are thereby compatible with the USB-CAT5 Extender.  
2.2.6 Compatibility  
The USB-CAT5 Extender complies with USB 1.1 specifications governing  
the design of full-speed and low-speed USB devices. However, Black Box  
does not guarantee that all USB 1.1 devices are compatible with the USB-  
CAT5 Extender.  
.
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHAPTER 3: Installation  
3.Installation  
3.1 Before You Begin  
Before you can install the USB-CAT5 Extender, you need to prepare your  
site.  
1. Determine where the host computer is to be located and set up the  
computer.  
2. Determine where you want to locate the USB device.  
3. If you are using surface cabling, ensure you have enough Category 5  
UTP cabling to connect the two locations.  
OR  
If you are using premise cabling, ensure Category 5 UTP cabling is  
installed between the two locations, with Category 5 information  
outlets located near both the computer and the USB device.  
3.2 Installing the Local Unit  
1. Place the Local Unit near the host computer.  
2. Plug the Type B connector on the USB cable (included) into the Host  
port on the Local Unit.  
3. Plug the Type A connector on the USB cable into the USB port on  
the computer.  
3.3 Installing the Remote Unit  
1. Place the Remote Unit near the USB device.  
3.4 Connecting the Local Unit to the Remote Unit  
NOTE  
To ensure proper operation, we recommend that only Category 5, or better, Unshielded Twisted Pair  
(UTP) cabling be used to connect the Local Unit to the Remote Unit. The UTP cabling must have a  
straight-through conductor configuration with no crossovers, and must be terminated with 8-conductor  
RJ45 connectors at both ends.  
3.4.1 With Surface Cabling  
1. Plug one end of the Category 5 UTP cabling (not included) into the  
Link port on the Local Unit.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SINGLE/DUAL USB-CAT5 EXTENDER 165FT  
2. Plug the other end of the Category 5 UTP cabling into the Link port  
on the Remote Unit.  
3.4.2 With Premise Cabling  
1. Plug one end of a Category 5 patch cord (not included) into the  
Link port on the Local Unit.  
2. Plug the other end of the patch cord into the Category 5 information  
outlet near the host computer.  
3. Plug one end of the second Category 5 patch cord (not included)  
into the Link port on the Remote Unit.  
4. Plug the other end of the second patch cord into the Category 5  
information outlet near the USB device.  
NOTE  
The maximum length of the Category 5 UTP cable, including patch cords, must not exceed 50 meters.  
3.5 Checking the Installation  
1. Check that the Link LEDs on both Local Unit and Remote Unit are  
on.  
3.6 Connecting a USB Device  
1. Install any software required to operate the USB device. Refer to  
the documentation for this device, as required.  
2. Connect the USB device to the Device port on the Remote Unit.  
3. Check that the Host LED on Local Unit is on.  
4. Check that the Device LED on Remote Unit is on.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHAPTER 4: Troubleshooting  
4.Troubleshooting  
4.1 Problems, Causes and Solutions  
The following table provides troubleshooting help. The topics are arranged  
in the order in which they should be executed in most situations. If you are  
unable to resolve the problem after following these instructions, please  
contact technical support for further assistance.  
Symptoms/Cause Remedy  
All LEDs on Local Unit 1. Ensure that the Local Unit is connected to a  
are off.  
USB port on the computer  
2. Check that the computer is switched on and  
that the OS is running (not in Sleep mode).  
Cause:  
The Local Unit is not  
receiving power from  
the computer  
Host LED on Local Unit 1. Ensure that a Category 5 UTP cable with  
is on; Link LED on  
Local Unit is off.  
straight-through conductors is connected  
between the Local Unit and the Remote Unit.  
2. Ensure that Category 5 cables and connectors  
are used throughout the entire link between  
the Local Unit and the Remote Unit.  
Cause:  
There is no connection  
between the Local Unit  
and the Remote Unit.  
3. Check that Category 3 cable has not been  
substituted.  
4. Check that the cable length between the Local  
Unit and the Remote Unit does not exceed 50  
metres.  
5. Connect a short Category 5 patch cord  
between the Local Unit and the Remote Unit.  
Recheck the operation of the system.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SINGLE/DUAL USB-CAT5 EXTENDER 165FT  
Symptoms/Cause Remedy  
Link LED on Local Unit 1. Check that the USB device is securely  
is on;  
connected to the USB port on the Remote  
Unit.  
Host LED on Local Unit  
is on.  
Link LED on Remote  
Unit is on;  
Device LED on Remote  
Unit is off.  
2. Disconnect the Local Unit from the computer.  
3. Connect the USB device directly to the USB  
port on the computer.  
4. If the device does not operate properly,  
consult the user documentation for the device.  
Cause:  
5. If the device operates properly when directly  
connected to the computer, connect another  
full speed device (of a different type) to the  
Remote Unit. Connect the Local Unit to the  
computer.  
a) The USB device is  
not connected to  
the Remote Unit.  
b) The USB device is  
malfunctioning.  
6. If the second device does not operate, the  
extender may be malfunctioning. Contact  
technical support for assistance.  
c) The computer does  
not recognise the  
USB device.  
7. If the second device does operate properly,  
the first device may not be compatible with the  
USB-CAT5 Extender. Contact technical  
support for assistance.  
d) The computer does  
not support USB  
hubs.  
e) The USB-CAT5  
Extender is  
malfunctioning.  
All LEDs on both Local 1. Disconnect the Local Unit from the computer.  
Unit and Remote Unit  
2. Connect the USB device directly to the USB  
are on but the device  
port on the computer.  
does not operate  
3. If the device does not operate properly,  
correctly  
consult the user documentation for the device.  
Cause:  
4. If the device operates properly when directly  
a) The USB device is  
connected to the computer, connect another  
full speed device (of a different type) to the  
malfunctioning.  
b) The computer does  
not recognise the  
USB device.  
Remote Unit. Connect the Local Unit to the  
computer.  
5. If the second device does not operate, the  
extender may be malfunctioning. Contact  
technical support for assistance.  
c) The USB-CAT5  
Extender is  
malfunctioning.  
6. If the second device does operate properly,  
the first device may not be compatible with the  
USB-CAT5 Extender. Contact technical  
support for assistance.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CHAPTER 4: Troubleshooting  
4.2 Calling Black Box  
If you determine that your USB-CAT5 Extender is malfunctioning, do not  
attempt to alter or repair the unit. It contains no user-serviceable parts.  
Contact Black Box at 724-746-5500.  
Before you do, make a record of the history of the problem. We will be able  
to provide more efficient and accurate assistance if you have a complete  
description, including:  
the nature and duration of the problem,  
when the problem occurs,  
the components involved in the problem,  
any particular application that, when used, appears to create the  
problem or make it worse.  
4.2.1 Shipping and Packaging  
If you need to transport or ship your USB-CAT5 Extender:  
Package it carefully. We recommend that you use the original  
container.  
If you are shipping the USB-CAT5 Extender for repair, make sure  
you include everything that came in the original package. Before  
you ship, contact Black Box to get a Return Authorization (RA)  
number.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SINGLE/DUAL USB-CAT5 EXTENDER 165FT  
Notes  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© Copyright 2004. Black Box Corporation. All rights reserved.  
1000 Park Drive  
Lawrence, PA 15055-1018  
724-746-5500  
Fax 724-746-0746  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bissell Vacuum Cleaner 59M5 User Manual
Black Decker Saw BPSC2135 User Manual
Blue Rhino Outdoor Fireplace WAD506AS User Manual
BOXLIGHT Projector Matinee 1HD User Manual
Brother Sewing Machine Computerized Embroidery Sewing Machine User Manual
Bushnell Digital Camera 98 1559 1 10 User Manual
Canon Printer S200SP User Manual
Canton Stroller 042 User Manual
Carrier Air Conditioner 024 User Manual
Chromalox Thermostat HVH TK5 User Manual