USER'S GUIDE
Matinee 1HD
HOME THEATER
PROJECTOR
Download from Www.Somanuals.com. All Manuals Search And Download.
To the Owner
Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable connections and try
the solutions in the Troubleshooting section at the end of this manual. If the problem still persists, contact BOXLIGHT.
SAFETY PRECAUTIONS
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
G This projector produces intense light from the projection lens. Do not stare directly into the lens as it could
possibly damage your eyes. Be especially careful that children do not stare directly into the beam.
G This projector should be installed as shown. If not, it may result in a fire hazard.
SIDE and TOP
REAR
G Provide appropriate space on the top, sides and rear of the
projector cabinet for allowing air circulation and cooling the
projector. Minimum clearance must be maintained. If the
projector is to be built into a compartment or similarly enclosed,
the minimum distances must be maintained. Do not cover the
ventilation slot on the projector. Heat build-up can reduce the
service life of your projector, and can also be dangerous.
20cm
50cm
50cm
50cm
G Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation
holes.
G If the projector is not to be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Moving the Projector
When moving the projector, close the front cover and retract the adjustable feet to prevent damage to the lens and cabinet.
When the projector is not in use for an extended period, put it into a suitable case.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
G Do not drop or bump a projector, otherwise damages or malfunctions may result.
G When carrying a projector, use a suitable carrying case.
G Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause
damage to a projector. To transport a projector through a courier or transport service, consult Boxlight dealer for best
way.
NOTE
Moving the projector from a cool temperature location to a warm temperature location may result in moisture condensation
on the Projection lens. In such an event, leave the projector OFF and wait until condensation disappears.
Installing the Projector in a Proper Position
Install the projector properly. Improper installation may reduce the lamp lifetime and cause a fire hazard.
20˚
Do not tilt the projector more than 20 degrees to either side.
20˚
Do not point the projector up to project an image.
NO UPWARD
Do not point the projector down to project an image.
NO DOWNWARD
Do not put the projector on either side to project an image.
NO SIDEWAYS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures :
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
Responsible party
Address
: Matinee 1HD
: Boxlight
: BOXLIGHT
: 19332 Powder Hill Place Poulsbo, WA 98370-7407 USA
: (800)762-5757 or +1-360-779-7901
Telephone No.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Connecting the AC Power Cord
This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects the correct input
voltage. It is designed to work with single-phase power systems
having a grounded neutral conductor. To reduce risk of electrical
shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of the type of power being supplied.
Connect the projector with all peripheral equipment before turning
the projector on. (Refer to page 11, 17, and 18 for connection.)
CAUTION
For safety, unplug AC Power Cord when the projector is not in
use.
When this projector is connected to an outlet with AC Power
Cord and the MAIN ON/OFF switch is on, it is in Stand-by mode
and consumes a little electric power. Turn the MAIN ON/OFF
switch off when the projector is not in use.
Connect AC Power Cord (supplied) to the projector.
The AC outlet must be near this equipment and must
be easily accessible.
NOTE ON THE POWER CORD
AC Power Cord must meet requirements of the country where you use a projector.
Confirm an AC plug type with the chart below and proper AC Power Cord must be used.
If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For the U.S.A. and Canada For Continental Europe
Ground
To POWER CORD
CONNECTOR on your
projector.
To the AC Outlet.
(120 V AC)
To the AC Outlet.
(200 - 240 V AC)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature and Design
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.
N Short Zoom Lens
N 16 : 9 Wide Screen
This projector is equipped with Short Zoom Lens which
allows you to enjoy 100" screen size in range of 9.8'
(3.0m) to 11.8' (3.6m).
The projector is equipped with LCD panels of 16 : 9 ratio
so that you can project the image from component video
signal such as a DVD player and high definition TV in a
full screen.
N Lens Shift
N One-Touch Auto PC Adjustment
The Lens Shift function gives you more flexibility when
installing the projector. It allows you to correct image
keystone issues without distorting the image.
Incoming computer video signals are recognized and the
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.
N Compact Design
This projector is extremely compact in size and weight.
It is designed to be carried anywhere you wish to use.
N Keystone Correction
Positioning height of a projector may result in distorted
image being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.
N Compatibility
This projector widely accepts various video and
computer input signals including;
G Computers
N Power Management
IBM-compatible or Macintosh computer up to 1280
The Power management function is provided to reduce
power consumption while the projector is not in use.
This Power management function operates to turn the
Projection lamp off when the projector detects signal
interruption and any button is not pressed over 5
minutes. The Projection lamp is automatically turned on
again when the projector detects signal or any operation
button is pressed.
x 1024 resolution.
G 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-
N color system can be connected.
G Component Video
Component video signal, such as a DVD player
output, high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i or 1080i, can be
connected.
This projector is shipped with this function ON.
G S-Video
N Lamp Mode
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
Either the Bright mode or the Theater black mode is
available in the Setting menu. The Theater black mode
is suitable for seeing a movie since it makes the image
best for a movie in low noise.
N High Resolution Image
This projector provides 964 x 544 dots resolution for
computer input. Resolution from a computer more than
964 x 544 and less than SXGA (1280 x 1024) is
compressed into 964 x 544 dots. This projector cannot
display image of over 1280 x 1024 dots. When
resolution of your computer is higher than 1280 x 1024,
set the computer output to a lower resolution.
N Multilanguage Menu Display
Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean, or Japanese.
N Illumination Buttons
The Remote Control is equipped with Light button and
Luminous buttons that make the remote control easier to
use in the dark.
N Multi-Scan System
This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Front
CAUTION
This projector is equipped with Cooling Fans for protection from overheating. Pay attention to the following to ensure
proper ventilation and avoid a possible risk of fire and malfunction.
G Do not cover vent holes.
G Keep back and bottom clear of any object. Obstructions may block cooling air.
EXHAUST VENTS
TOP CONTROLS
AND INDICATORS
AIR INTAKE VENTS
CAUTION
Do not put heat-sensitive
objects on the top.
FRONT COVER
AIR INTAKE VENTS
INFRARED
REMOTE RECEIVER
FOCUS RING
ZOOM LEVER
LENS SHIFT RING
(LEFT/RIGHT)
LENS SHIFT RING
(UP/DOWN)
PROJECTION LENS
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Bottom
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
AIR INTAKE VENTS
AND AIR FILTERS
AIR INTAKE VENTS
LAMP COVER
CAUTION
Do not put any objects at
the bottom that could
obstruct air circulation.
Back
TERMINALS
AND CONNECTORS
POWER CORD CONNECTOR
MAIN ON/OFF
SWITCH
See the caution
below.
EXHAUST VENTS
CAUTION
Hot air is exhausted from the exhaust vents. When using or installing the projector, the following
precautions should be taken.
G Do not put any flammable objects near these vents.
G Keep front grills at least 3’(1m) away from any objects, especially heat-sensitive objects.
G Do not touch this area (including the top cabinet), especially screws and metallic parts. This area will
become hot while the projector is used.
This projector detects internal temperature and will automatically adjust the speed of the Cooling
Fans.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Terminal
COMPUTER INPUT
TERMINAL
Connect the computer
output to this jack.
SERVICE PORT JACK
This jack is used to service
the projector.
(Refer to page 18.)
*
S-VIDEO INPUT JACK
VIDEO INPUT JACK
(VIDEO)
Connect the composite
video output from video
equipment to VIDEO jack.
(Refer to page 17.)
COMPONENT VIDEO INPUT JACK
Y-Pb/Cb-Pr/Cr
(
)
Connect the S-VIDEO
output from video
equipment to this
jack. (Refer to page
17.)
Connect the component video
outputs to Y, Pb/Cb, and Pr/Cr
jacks.
(Refer to page 17.)
This projector uses a micro processor to control this unit, and occasionally, this micro processor may malfunction and need to
be reset. This can be done by pressing the RESET button with a pen, which will shut down and restart the unit. Do not use
the RESET function excessively.
*
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Top Controls and Indicators
LAMP REPLACE INDICATOR
WARNING TEMP. INDICATOR
READY INDICATOR
LAMP INDICATOR
Turns yellow when the
life of the projection
lamp draws to an end.
(p44)
Flashes red when internal
projector temperature is
too high. (p46)
Lights green when the
projector is ready to be
turned on. It flashes
Becomes dim when the
projector is turned on.
And it is bright when
the projector is in
stand-by mode.
green
in
Power
management mode.
(p43)
WARNING
TEMP.
READY
LAMP
REPLACE
LAMP
ON-OFF
POWER ON–OFF BUTTON
Used to turn the projector
on or off. (p19)
INPUT BUTTON
Used to select input
source. (p24, 31)
MENU
INPUT
SELECT
MENU BUTTON
SELECT BUTTON
POINT BUTTONS
Used to open or close
the on-screen menu.
(p22)
Used to execute the item
selected. It is also used
to expand the image in
Digital zoom mode.
(p41)
Used to select an item or adjust
value in the on-screen menu. They
are also used to pan the image in
Digital zoom mode. (p41)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control
LIGHT BUTTON
POWER ON-OFF BUTTON
Used to turn the projector
on or off. (p19)
Used to light the following
buttons for about 10
seconds: LIGHT, ON-OFF,
AUTO, MENU, SCREEN,
INPUT, and IMAGE.
ON-OFF
SCREEN
AUTO PC ADJ.
AUTO
LIGHT
MENU
SCREEN BUTTON
Used to select screen
size. (p30, 41)
AUTO PC ADJ. BUTTON
Used to operate Auto PC
Adjustment function. (p34)
POINT BUTTONS
SELECT
Used to select an item or
adjust value in the on-
screen menu. They are
also used to pan the image
in Digital zoom mode. (p41)
MENU BUTTON
Used to open or close the
On-screen menu. (p22)
INPUT
IMAGE
INPUT BUTTON
SELECT BUTTON
Used to select input source.
(p24, 31)
VIDEO
IMAGE
Used to execute the item
selected. It is also used to
expand the image in Digital
zoom mode.(p41)
NO SHOW
AUTO
1
NO SHOW BUTTON
Used to show a blank, black
image. (p21)
VIDEO
2
3
4
KEYSTONE
S-VIDEO
IMAGE BUTTON
Used to select image level.
(p27, 38)
COMPONENT
COMPO
VIDEO BUTTON
Used to select video input
source. (p24)
KEYSTONE BUTTONS
Used to correct the
keystone distortion.
(p21, 42)
LUMINOUS BUTTONS
The luminous buttons in the
frame emit light in a dark
place after they are put
under light for a while.
To insure safe operation, please observe the following
precautions :
G Do not bend, drop the remote control, or expose the
remote control to moisture or heat.
G For cleaning, use soft dry cloth. Do not apply
benzene, thinner, splay or any chemical material.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Batteries Installation
Remove the battery
compartment lid.
Slide the batteries
into compartment.
Replace the compartment lid.
1
2
3
Two AA size batteries
Pull up the lid
and remove it.
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
* When the batteries of the remote control are replaced, the remote
control code automatically returns to the initial code (Code 2)(p43).
To insure safe operation, please observe the following precautions:
G Use (2) AA, UM3 or R06 type alkaline batteries.
G Replace two batteries at the same time.
G Do not use a new battery with a used battery.
G Avoid contact with water or liquid.
G Do not expose the remote control to moisture, or heat.
G Do not drop the remote control.
G If a battery has leaked on the remote control, carefully wipe case clean and install new batteries.
G Risk of explosion if battery is replaced by an incorrect type.
G Dispose of used batteries according to the instructions.
Operating Range
Point the remote control toward the projector (Infrared
Remote Receiver) whenever pressing any button. Maximum
operating range for the remote control is about 16.4’ (5m)
and 60° in front of the projector.
60°
16.4’
(5 m)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Positioning the Projector
G This projector is designed to project on a flat projection surface.
G The projector can be focused from 3.6’(1.1m) ~ 19.7’(6.0m).
G Refer to the figure below to adjust a screen size.
ROOM LIGHT
The brightness in a room has a great influence on
picture quality. It is recommended to limit
ambient lighting in order to provide the best
image.
*The lens is at the top of the lens shift.
19.7’(6.0m)
14.8’ (4.5m)
9.8’ (3.0m)
200”
Max. Zoom
150”
125”
3.9’(1.2m)
169”
Min. Zoom
100”
83”
H
40”
31”
30"
40”
100”
150”
200”
Screen Size
(W x H) mm
663 x 373
884 x 497
4.6' (1.4m)
3.9’ (1.2m)
2209 x 1244
11.8' (3.6m)
9.8’ (3.0m)
3314 x 1866
17.7' (5.4m)
14.8' (4.5m)
4419 x 2489
–––––
3.6’(1.1m)
Zoom (min)
Zoom (max)
19.7’(6.0m)
–––––
Tilting the Projector
Picture tilt and projection angle can be adjusted by rotating the
Adjustable feet. Projection angle can be adjusted up to 11.8
degrees with the Adjustable feet.
Lift the front of the projector and pull the Feet lock latches on
both sides of the projector.
1
Release the Feet lock latches to lock the Adjustable feet and
rotate the Adjustable feet to adjust position and tilt.
2
To retract the Adjustable feet, lift the front of the projector
and pull and undo the Feet lock latches.
Keystone distortion of a projected image can be adjusted by
menu operation or the remote control. (Refer to page 21 and
42.)
3
ADJUSTABLE FEET
CAUTION
FEET LOCK
LATCH
Tilt the projector within the adjustable range in order not to shorten
the life of the lamp. Proper angle should be taken. Refer to page
5.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Moving the Lens
The Projection lens can be moved up and down with manual lens shift function. This function makes it easy to provide a
projected image where you want. U/D ratio can be adjusted from 10 : 0 ~ 0 : 10 (refer to the figures below).
Turn the lens shift ring (left/right) left/right to move the lens leftward /
rightward.
LENS SHIFT RING
(LEFT/RIGHT)
Turn the lens shift ring (up/down) up/down to move the lens upward /
downward.
LENS SHIFT RING
(UP/DOWN)
LENS SHIFT UP/DOWN
UPPERMOST
DOWNMOST
LENS SHIFT LEFT/RIGHT
25%
25%
LEFTMOST
NOTE
RIGHTMOST
The best image is generally obtained at the center without the Lens shift.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Video Equipment
Cables used for connection
• Video Cable (RCA x 1 or RCA x 3)
• S-VIDEO Cable
• Scart-VGA Cable
*Only a video cable is included.
Component video output equipment.
(such as DVD player or high-definition
TV source.)
Video Source (example)
Video Cassette Recorder
Video Disc Player
S-VIDEO Output
RGB Scart
21-pin Output
Composite
Video Output
Component Video Output
(Y-Pb/Cb-Pr/Cr)
S-VIDEO
Cable
✽ Scart-VGA
Cable
Video Cable
(RCA x 1)
Video Cable
(RCA x 3)
Connect these 3 jacks
properly.
S-VIDEO
COMPUTER IN
VIDEO
Y - Pb/Cb - Pr/Cr
✽ Scart-VGA Cable
Connection
When RGB Scart 21-pin
output is available on
video equipment, connect
the Scart connector to the
"COMPUTER IN" on the
projector with an optional-
ly supplied Scart-VGA
cable. Use our cable.
We do not guarantee per-
formance of the other
cables.
(See page 51 for order.)
Terminals
of the Projector
NOTE
When selecting the video input with the "AUTO" on the remote control or
through menu operation, the projector selects connection in the following
order:
NOTE :
When connecting the cable, the power
cords of both the projector and the external
equipment should be disconnected from
AC outlet.
1st
Y-Pb/Cb-Pr/Cr
2nd S-VIDEO
3rd VIDEO
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to a Computer
Cables used for connection
• VGA Cable (HDB 15 pin) ✽
• MAC Adapter (When connecting to Macintosh computer) ✽
✽ option
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor Output
N MAC ADAPTER (Not supplied)
MAC Adapter ✽
Set slide switches
according to the
chart.
Set switches as shown in the table
below depending on RESOLUTION
MODE that you want to use before
you turn on projector and computer.
ON
ON
DIP
1
2
3
4
5
6
OFF
3
1
2
4
5
6
VGA Cable ✽
13" MODE (640 x 480)
ON
ON OFF OFF OFF OFF
16" MODE (832 x 624) OFF ON OFF ON OFF OFF
19" MODE (1024 x 768) OFF ON
21" MODE (1152 x 870) ON ON
ON OFF OFF OFF
ON ON OFF OFF
COMPUTER IN
Terminals
of the Projector
NOTE :
When connecting the cable, the power
cords of both the projector and the external
equipment should be disconnected from
AC outlet. Turn the projector and
peripheral equipment on before the
computer is switched on.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning On the Projector
Complete peripheral connections (with Computer, VCR, etc.)
before turning on the projector.
1
2
Connect the projector's AC Power Cord into an AC outlet, and
open the front cover. Turn the MAIN ON/OFF switch on. The
LAMP indicator lights red, and the READY indicator lights green.
The READY indicator does not light green with the front cover
closed.
Open the front cover.
MAIN ON/OFF switch
Press the POWER ON-OFF button on the top control or on the
remote control. The LAMP indicator dims, and the cooling fans
start to operate. The preparation display appears and the count-
down starts (for 30 seconds).
3
4
OFF
ON
The input source that was selected last and the Lamp mode
status icon appears on a screen after the count-down. Select an
input source of either video or computer. (Refer to page 24 or
31.)
Lamp mode
Lamp mode
Bright light (Bright mode)
*Refer to page 43 for the Lamp mode.
Light with head gray (Theater black mode)
Turning Off the Projector
Press the POWER ON-OFF button on the top control or the
remote control, and the message "Power off?" appears on the
screen. This message is not displayed and the projector is
turned off when the Power off confirmation function is off. (See
the Setting menu on page 43.)
1
2
3
Power off?
Press the POWER ON-OFF button again to turn off the
projector. The LAMP indicator lights bright and the READY
indicator turns off. The cooling fans operate for about 90
seconds. During this "Cooling Down" period, leave the front
cover open. (The projector cannot be turned on.)
Message disappears after 4 seconds.
When the projector has cooled down, the READY indicator lights
green again. Turn the MAIN ON/OFF switch off and disconnect
the AC Power Cord. Do not disconnect the AC Power Cord
before the READY indicator lights green.
CAUTION
For safety, the projector will be turned off when the front cover is closed in the middle of operation. However, do
not close the front cover for the purpose of turning off the projector. Close the front cover after the projector has
cooled down and the READY indicator lights green.
NOTE
To maintain the life of the lamp, once you turn the projector on, wait at least 5 minutes before turning it off.
Do not use the projector for more than 24 hours continuously. Turn off the projector at least once every 24 hours and give it
a rest. Continuous use may result in shortening the lamp lifetime.
When the “Power management” function is ON, the projector detects signal interruption and turns off the Projection lamp
automatically. Refer to “Power management” on page 43.
When the WARNING TEMP. indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes before
turning on the projector again. (Refer to the section "Warning Temp. Indicator" on page 46.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Focus Adjustment
Rotate the FOCUS RING to adjust the image focus.
FOCUS RING
Zoom Adjustment
Move the ZOOM LEVER upward to make the image larger. Move the
ZOOM LEVER downward to make the image smaller.
ZOOM LEVER
WIDE
TELE
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Keystone Adjustment
If the projected image has keystone distortion after adjusting the lens shift, correct the image with the Keystone Adjustment.
Press the KEYSTONE L/M button on the remote control or
select the Keystone in the Setting menu. (Refer to page 42.)
The Keystone dialog box appears.
1
Correct keystone distortion by pressing the KEYSTONE L/M
button or the POINT UP/DOWN button. Press the KEYSTONE
2
• The arrows are white when there is no
correction.
• The arrow disappears at the maximum
correction.
L button or the POINT UP button to reduce the upper part of
image, and press the KEYSTONE M button or the POINT
DOWN button to reduce the lower part.
• The direction of the arrow being corrected turns
purple.
Reduce the upper width with the KEYSTONE L
button or the POINT UP button.
Reduce the lower width with the KEYSTONE M
button or the POINT DOWN button.
Keystone Adjustment Hint
Use the Lens shift function first to move the screen for the quality of image before using the Keystone adjustment function.
Moving the screen with the Lens shift function produces a better image than keystone adjustment function.
No Show Function
Press the NO SHOW button on the remote control to black out the
image. To restore to normal, press the NO SHOW button again or
press any other button.
No show
Message disappears after 4 seconds.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
On-Screen Menu
The projector has the on-screen menu that provides a variety of adjustment and settings.
Display the on-screen menu by pressing the MENU button on
the top control or the remote control. A main menu appears.
TOP CONTROL
REMOTE CONTROL
1
2
MENU
SCREEN
MENU
SELECT
SELECT
MENU button
Main menu
Select a menu from the main menu by pressing the POINT
UP/DOWN button, and press the POINT RIGHT button to
enter the sub-menu. (The selected icon turns yellow.)
MENU
ITEM
POINT
RIGHT
BUTTON
Select an item by pressing the POINT UP/DOWN button, and
Sub-menu
activate the item that you have selected by the
or
3
4
,
,
button.
Press the MENU button again to close the on-screen menu.
SELECT BUTTON
Press the SELECT button to activate the item that you have
selected.
POINT LEFT BUTTON
Press the POINT LEFT button to go on or adjust values.
POINT RIGHT BUTTON
Close the menu.
Press the POINT RIGHT button to go on or adjust values.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Contents of Menus
VIDEO MENUS
INPUT SOURCE SELECTION: select input source either Video [Auto, Video, S-Video, (Y-Pb/Cb-Pr/Cr)] or
Computer. (Refer to page 24, 25.)
VIDEO SYSTEM SELECTION: select Video system from AUTO, PAL, SECAM, NTSC, NTSC4.43, PAL-M,
PAL-N, 1080i, 1035i, 720p, 575p, 480p, 575i, 480i. (Refer to page 26.)
IMAGE LEVEL SELECTION: select image level from Standard, Cinema, and Image 1 ~ 4. (Refer to page
27.)
IMAGE LEVEL ADJUSTMENT: adjust Contrast / Brightness / Color / Tint / Color temp. / White balance (R/G/B) /
Sharpness / Gamma / Auto grayscale / Auto fleshtone. (Refer to page 28, 29.)
SCREEN SIZE ADJUSTMENT: set the screen size from Full, Zoom, or Normal. (Refer to page 30.)
SETTING: change various settings; Language, Keystone, Blue back, Display, Menu position, Logo, Ceiling,
Rear, Power management, Power off confirmation, Lamp mode, Remote control, and Lamp
counter reset. (Refer to page 42.)
COMPUTER MENUS
INPUT SOURCE SELECTION: select input source either Computer or Video [Auto, Video, S-Video, (Y-Pb/Cb-
Pr/Cr)]. (Refer to page 31.)
COMPUTER SYSTEM SELECTION: select computer system available. (Refer to page 32.)
COMPUTER ADJUSTMENT: select Auto PC Adj. or adjust Fine sync, Total dots, Horizontal, Vertical, Current
mode, Clamp, Display area, Display area H, Display area V, Full screen, and
use Reset, Mode free, and Store. (Refer to page 34-37.)
IMAGE LEVEL SELECTION: select image level from Standard, Real, and Image 1 ~ 4. (Refer to page 38.)
IMAGE LEVEL ADJUSTMENT: adjust Contrast / Brightness / Color temp. / White balance (R/G/B) / Sharpness /
Gamma / Auto grayscale / Auto fleshtone. (Refer to page 39, 40.)
SCREEN SIZE ADJUSTMENT: set the size from Normal, Full, True, and Digital zoom. (Refer to page 41.)
SETTING: change various settings; Language, Keystone, Blue back, Display, Menu position, Logo, Ceiling,
Rear, Power management, Power off confirmation, Lamp mode, Remote control, and Lamp
counter reset. (Refer to page 42.)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Input Source Selection (Direct Operation)
INPUT BUTTON
You can select Video input or Computer input with the INPUT button.
(The input source that was selected last is selected when the projector
is turned on.)
INPUT button
Video
If the projector cannot reproduce proper video source, select correct
input source through menu operation on the next page.
Computer
RGB Scart Input
TOP CONTROL
REMOTE CONTROL
To select RGB Scart 21-pin video input through the computer input
terminal, follow the procedures described at the section "Input Source
Selection" on page 31.
INPUT
IMAGE
INPUT
SELECT
VIDEO
IMAGE
NO SHOW
AUTO
1
VIDEO
2
INPUT button
REMOTE CONTROL
AUTO / VIDEO / S-VIDEO / COMPO BUTTON
Press AUTO, VIDEO, S-VIDEO, or COMPO button on the remote
control according to video input.
*It is convenient for you to select AUTO as the projector automatically
detects incoming video signal, and adjust itself to optimize its
performance.
INPUT
IMAGE
VIDEO
IMAGE
NO SHOW
AUTO
1
When selecting AUTO, the projector automatically
VIDEO
2
3
4
AUTO
detects incoming video signal, and adjusts itself to
optimize its performance. The projector selects
connection in the following order:
1st Y-Pb/Cb-Pr/Cr
KEYSTONE
S-VIDEO
COMPONENT
COMPO
2nd S-VIDEO
3rd VIDEO
The Y-Pb/Cb-Pr/Cr has priority over the S-VIDEO. The
S-VIDEO has priority over the VIDEO.
AUTO / VIDEO / S-VIDEO / COMPO button
When video input signal is connected to VIDEO, select
Video.
VIDEO
When video input signal is connected to S-VIDEO, select
S-Video.
S-VIDEO
When video input signal is connected to Y-Pb/Cb-Pr/Cr,
select COMPO.
COMPO
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Input Source Selection (Menu Operation)
Input Source Selection menu
Press the MENU button, and the main menu appears. Select
1
the Input Source Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
Input Source Selection menu
Choose Video with the POINT UP/DOWN button and press
the POINT RIGHT button. The source selection menu
appears.
2
3
Move the pointer to the source that you want to select with the
POINT UP/DOWN button, and press the SELECT button. Close
the source selection menu.
Source Selection menu (VIDEO)
pointer
Close the source selection menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Video input
Video System Selection (Video / S-Video)
Press the MENU button, and the main menu appears. Select
Video System Selection menu (VIDEO / S-VIDEO)
the Video System Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
displays the
selected
system.
Video System Selection menu
Choose the system that you want to select with the POINT
UP/DOWN button, and then press the SELECT button to
activate the item.
Auto
The projector automatically detects the incoming video system, and
adjusts itself to optimize its performance.
However, when video system is PAL-M or PAL-N, select either PAL-M
or PAL-N manually.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If the projector cannot reproduce proper video image, select a specific
system among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
Close the Video System Selection menu.
Video System Selection (Y-Pb/Cb-Pr/Cr)
Press the MENU button, and the main menu appears. Select
Video System Selection menu (Y-Pb/Cb-Pr/Cr)
the Video System Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
Choose the system that you want to select with the POINT
UP/DOWN button, and then press the SELECT button to
activate the item.
2
Auto
The projector automatically detects the incoming video system, and
adjusts itself to optimize its performance.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, select a specific
component video system among 480i, 575i, 480p, 575p, 720p, 1035i,
and 1080i.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Image Level Selection (Direct Operation)
Select the image level from Standard, Cinema, Image 1, Image 2,
Image 3, and Image 4 by pressing the IMAGE button on the remote
control. (See the next section "Image Level Selection (Menu
Operation)" about each item.)
IMAGE button
Standard
IMAGE button
Cinema
Image 1
Image 2
Image 3
Image 4
INPUT
IMAGE
VIDEO
IMAGE
NO SHOW
AUTO
1
VIDEO
2
3
4
KEYSTONE
S-VIDEO
COMPONENT
COMPO
IMAGE 1-4 button
Image Level Selection (Menu Operation)
Press the MENU button, and the main menu appears. Select
Image Level Selection menu
the Image Level Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Image Level Selection
menu
Choose the level that you want to set with the POINT UP/DOWN
button, and then press the SELECT button to activate it.
The level being selected.
Standard
Normal picture adjustment preset on this projector.
Cinema
Picture level adjusted for the picture with fine tone.
IMAGE 1~4
User preset picture adjustment in Image Level Adjustment menu (p28,
29).
Close the Image Level Selection menu.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Image Level Adjustment
Press the MENU button, and the main menu appears. Select
Image Level Adjustment menu
the Image Level Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Image Level Adjustment
menu
Choose the item that you want to adjust with the POINT
UP/DOWN button, and then press the POINT LEFT/RIGHT
button to adjust each item. The items displayed in a line can be
adjusted while you see the change of the image. Press the
SELECT button to finish adjusting an item. The on-screen menu
returns to the sub-menu.
Press the
SELECT button
at this icon to
display other
items.
Press the SELECT button at this
icon to close the item.
To store the adjustment data, select Store with the POINT
UP/DOWN button and press the POINT RIGHT button.
3
4
Reset
To reset to previous settingsl, select Reset with the POINT
UP/DOWN button and press the POINT RIGHT button. Select
"Yes" with the SELECT button.
Select the Store.
Choose one of the positions from Image Level 1 to 4 that you
want to store with the POINT UP/DOWN button, and press the
SELECT button. Select "Yes" with the SELECT button and
close the menu by pressing the SELECT button at Quit.
NOTE
All the items on the next page can be memorized in Image 1-4.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
The items that you can adjust are the following:
Contrast
Press the POINT LEFT button to decrease contrast and the POINT RIGHT button to increase contrast. (From 0 to 63.)
Brightness
Press the POINT LEFT button to adjust image darker and the POINT RIGHT button to adjust image brighter. (From 0 to 63.)
Color
Press the POINT LEFT button to lighten color and the POINT RIGHT button to deepen color. (From 0 to 63.)
Tint
Press the POINT LEFT button or the POINT RIGHT button to obtain proper color. (From 0 to 63.)
Color temp.
Press the POINT LEFT button or the POINT RIGHT button for Color temp. level that you want to select. (XLow, Low, Mid, or
High)
White balance (Red)
Press the POINT LEFT button to lighten red tone and the POINT RIGHT button to deepen red tone. (From 0 to 63.)
White balance (Green)
Press the POINT LEFT button to lighten green tone and the POINT RIGHT button to deepen green tone. (From 0 to 63.)
White balance (Blue)
Press the POINT LEFT button to lighten blue tone and the POINT RIGHT button to deepen blue tone. (From 0 to 63.)
Sharpness
Press the POINT LEFT button to soften the image and the POINT RIGHT button to sharpen the image. (From 0 to 15.)
Gamma
Press the POINT LEFT button or the POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)
Auto grayscale
When this function is "ON", it automatically enhances contrast of bright and dark part of image.
Auto fleshtone
When this function is "ON", it produces more vivid image according to image condition.
Reset
Reset all adjustment to their previous levels. (The Reset does not work for the stored data.)
Store
Store the adjustment data.
NOTE : Tint cannot be adjusted when the video
Quit
system is PAL, SECAM, PAL-M or PAL-N.
Close the Image Level Adjustment menu.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Screen Size Adjustment (Direct Operation)
Select the screen size among Full, Zoom, and Normal by pressing the
SCREEN button on the remote control. (See the next section "Screen
Size Adjustment (Menu Operation)" about each item.)
SCREEN button
Full
SCREEN button
AUTO PC ADJ.
LIGHT
AUTO
Zoom
MENU
SCREEN
Normal
SELECT
Screen Size Adjustment (Menu Operation)
This projector has a picture screen resize function, which enables you to display the desirable image size.
Screen Size Adjustment menu
Press the MENU button, and the main menu appears. Select
the Screen Size Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
NOTE : The Screen Size Adjustment cannot be operated when
“720p,” “1035i,” or “1080i” is selected in the Video
System Selection menu (p26).
Screen Size Adjustment menu
Choose the item that you want to set with the POINT UP/DOWN
button, and then press the SELECT button to activate it.
Press the
SELECT button
at this icon to
activate the
item.
2
Full
Provides an image to fit width of screen by expanding the image width
uniformly. This function can be used for providing a squeezed video
signal at wide video aspect ratio of 16 : 9.
When your video equipment (such as DVD) has 16 : 9 output mode,
select 16 : 9 and select the Full on this Screen Size Adjustment menu
to provide better quality.
Close the Screen Size Adjustment menu.
Zoom
Full
Provides an image to fit screen size (16 : 9 aspect ratio) by expanding
the image width and height uniformly. This function can be used for
providing a letter box mode picture (4 : 3 aspect picture with black bar
on the top and bottom edges) at wide video aspect of 16 : 9.
Normal
Zoom
Provides an image at the normal video aspect ratio of 4 : 3.
Normal
30
Download from Www.Somanuals.com. All Manuals Search And Download.
/ (RGB Scart 21-Pin Video Input)
Computer Input
Input Source Selection (Direct Operation)
INPUT BUTTON
You can select Computer input or Video input with the INPUT button.
(The input source that is selected last is selected when the projector is
turned on.)
INPUT button
Computer
If the projector cannot reproduce proper image, select a correct input
source through menu operation as shown below.
Video
RGB Scart Input
TOP CONTROL
REMOTE CONTROL
When RGB Scart 21-pin output is available in video equipment,
connect the Scart connector to the "COMPUTER IN" on the projector
with an optionally supplied Scart-VGA cable. It can reproduce higher
resolution and quality of picture. (See page 51 for order.)
To select RGB Scart input, follow the procedures described below.
INPUT
IMAGE
INPUT
SELECT
VIDEO
IMAGE
NO SHOW
AUTO
1
Note
VIDEO
2
The RGB Scart input (COMPUTER IN) can receive 575i only.
INPUT button
Input Source Selection (Menu Operation)
Press the MENU button, and the main menu appears. Select
Input Source Selection menu
the Input Source Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
Input Source Selection menu
Choose Computer with the POINT UP/DOWN button and press
the POINT RIGHT button. The Source selection menu appears.
2
3
Close the Input Source Selection menu.
Move the pointer to the source that you want to select with the
POINT UP/DOWN button, and press the SELECT button.
To select computer input, select RGB.
To select RGB Scart 21-pin video input, select the RGB (Scart).
Close the source selection menu.
Source Selection menu
*Select RGB (Scart) only when connecting the projector with the
Scart-VGA cable.
Close the source selection menu.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Computer System Selection
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, or SXGA in most cases
(refer to “Compatible Computer System” on the next page). When selecting Computer, this projector automatically tunes to
incoming signal and projects proper image without any special settings.
The projector displays one of the Auto, - - -, Mode 1/2/3/4/5, or the system provided in the projector.
When the projector cannot recognize the connected
system as computer system provided in this projector,
Auto PC Adjustment function operates to adjust the
projector and the message “Auto” is displayed on the
System box. (Refer to p34.) Store the adjusted data by
the Auto PC Adjustment function so as to use the system
again. When the image is not provided properly, manual
adjustment is required. (Refer to page 35, 36, and 37.)
Computer System Selection menu
Auto
The System
box displays
the system
being selected.
There is no signal input from the connected computer.
Make sure the connection of the computer and the
projector is set correctly.
- - -
(Refer to the Troubleshooting section on page 47.)
User preset adjustment in Computer Adjustment
(Manual). Adjustment data can be stored Mode 1 - 5.
Mode 1
SVGA 1
Computer systems provided in the projector. The
projector chooses proper system and displays it.
*Mode 1 and SVGA 1 are examples.
Custom Mode (1~5) set in the
Computer Adjustment menu. (p35-37)
Press the MENU button, and the main menu appears. Select
the Computer System Selection menu with the POINT
1
UP/DOWN button, and then press the POINT RIGHT button to
enter the sub-menu.
Computer System Selection menu
Computer System Selection menu
Selected System
Choose the system that you want to select with the POINT
UP/DOWN button, and then press the SELECT button to
activate the item.
2
The systems
displayed on
the on-screen
menu can be
selected.
Close the Computer System Selection menu.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Compatible Computer System
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 100
MHz of Dot Clock.
ON-SCREEN
DISPLAY
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.625
15.734
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
XGA 4
XGA 5
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1152 x 900
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
58.03
60.24
68.68
64.20
61.20
50.00
50.00
61.85
46.43
31.25
45.00
33.75
33.75
28.125
70.07
74.92
60.02
54.58
79.35
VGA 3
XGA 6
VGA 4
XGA 7
VGA 5
XGA 8
87.17
VGA 6
XGA 9
(Interlace)
VGA 7
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA 15
MAC 19
MAC 21
SXGA 1
SXGA 11
77.07
75.70
MAC LC13
MAC 13
RGB
86.96
640 x 480
––––––––
(Interlace)
50.00
58.20
58.30
72.00
75.08
75.06
70.40
65.20
(Interlace)
60.00
(Interlace)
––––––––
RGB
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
86.00
(Interlace)
94.00
(Interlace)
SXGA 13 1280 x 1024
SXGA 14 1280 x 1024
SXGA 17
1152 x 900
66.00
86.70
SXGA 18 1280 x 1024
(Interlace)
50.00
(Progressive)
––––––––
575p
60.00
(Progressive)
––––––––
720p
60.00
(Interlace)
60.00
(Interlace)
50.00
(Interlace)
––––––––
1035i
––––––––
1080i60
––––––––
XGA 2
1080i50
XGA 3
NOTE
Specifications are subject to change without notice.
This projector cannot display any resolution higher than 1280 X 1024. If your computer’s screen resolution is
higher than 1280 X 1024, reset the resolution to the lower before connecting projector.
The image data in other than 964 x 544 is modified to fit the screen size automatically.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Computer Adjustment (Auto) (Direct Operation)
The Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to
conform to your computer. The Auto PC Adjustment function can be operated as follows.
Press the AUTO PC ADJ. button on the remote control, and the func-
tion works.
REMOTE CONTROL
To store the adjustment data, follow the step 3 and 4 on page 35, 36.
ON-OFF
AUTO PC ADJ. button
AUTO PC ADJ.
LIGHT
AUTO
MENU
SCREEN
Computer Adjustment (Auto) (Menu Operation)
Press the MENU button, and the main menu appears. Select
Computer Adjustment menu
the Computer Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Computer Adjustment menu
Shows status (Stored/Free) of the
selected mode.
Choose the Auto PC Adj., and then press the SELECT button to
activate it.
Selected Mode
Auto PC Adj.
adjusts Fine sync, Total dots, Horizontal, and Vertical to conform to
your computer.
To store the adjustment parameters by Auto PC Adjustment,
follow the step 3 and 4 on page 35, 36. Once the parameters are
memorized, the setting can be done just by selecting Mode in
the Computer System Selection menu.
3
NOTE
The Fine sync, Total dots, Horizontal, and Vertical of some computers cannot be fully adjusted with this Auto PC Adjustment
function. When the image is not provided properly through this function, manual adjustments are required. (Refer to page
35-37.)
The Auto PC Adjustment function cannot be operated when “720p (HDTV),” “1035i (HDTV)”, or “1080i (HDTV)” is selected in
the Computer System menu (p32).
The Computer Adjustment menu cannot be operated when "RGB" is selected in the Computer System menu or "RGB
(Scart)" is selected in the Source Selection menu.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Computer Adjustment (Manual)
This projector can automatically tune to the display signals from most personal computers currently distributed. However,
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-
Scan system of this projector. If this happens, the projector cannot reproduce a proper image and the image may be
recognized as a flickering picture, a non-synchronized picture, a non-centered picture, or a skewed picture.
This projector has a manual computer adjustment to enable you to precisely adjust several parameters to match with those
special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted.
This enables you to recall the setting for a specific computer whenever you use it.
Press the MENU button, and the main menu appears. Select
the Computer Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
Computer Adjustment menu
1
2
Computer Adjustment menu
Shows status
Press POINT
LEFT/RIGHT button
to adjust the value.
Choose the item that you want to adjust, and then press the
POINT LEFT/RIGHT button to adjust the value. The Fine sync
and Total dots are displayed in a line. Press the SELECT button
after adjusting them. The on-screen menu returns to the sub-
menu.
(Stored/Free) of the
selected mode.
Selected Mode
Press the
SELECT button
at this icon to
display other
items.
Press the SELECT button at this
icon to close the item.
To store the adjustment parameters, select the Store with the
POINT UP/DOWN button and press the POINT RIGHT button.
3
Reset
To reset to previous level, select the Reset with the POINT
UP/DOWN button and press the POINT RIGHT button. Select
"Yes" with the SELECT button.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Choose one of the positions from the Mode 1 to 5 where you
To store adjustment data.
want to store with the POINT UP/DOWN button, and press the
SELECT button. Select "Yes" with the SELECT button and
close the menu by pressing the SELECT button at the Quit.
4
5
Vacant Mode
This Mode has parameters being stored.
To clear the adjustment parameters previously set, select the
Mode free with the POINT UP/DOWN button and press the
POINT RIGHT button. Choose the mode that you want to clear
with the POINT UP/DOWN button, and then press the SELECT
button. Select "Yes" with the SELECT button and close the
menu by pressing the SELECT button at the Quit.
To clear adjustment data.
Shows values of “Total dots,”
“Horizontal,” “Vertical,” “Display
area H,” and “Display area V.”
Quit
The items that you can adjust are the following:
Fine sync
Adjust an image as necessary to eliminate flicker from the display. Press the POINT LEFT/RIGHT button to adjust
value.(From 0 to 31.)
Total dots
The number of total dots in one horizontal period. Press the POINT LEFT/RIGHT button and adjust number to match your
computer image.
Horizontal
Adjust horizontal picture position. Press the POINT LEFT/RIGHT button to adjust the position.
Vertical
Adjust vertical picture position. Press the POINT LEFT/RIGHT button to adjust the position.
Press the POINT
RIGHT button at the
Current mode icon to
show the information of
the computer
Current mode
Current mode
Press the POINT RIGHT button to show the information of the
computer connected.
connected.
Clamp
Adjust clamp level. When the image has a dark bar(s), try this adjustment.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Display area
Display area
Select the area displayed by the projector. Select the resolution from
the Display area dialog box.
Press the POINT RIGHT button
at the Display area and the
Display area dialog box appears.
NOTE : The Display area, Display area (H/V) and Full screen cannot
be adjusted when “1035i (HDTV)” or “1080i (HDTV)” is
selected in the Computer System Selection menu (p32).
Display area H
Adjustment of horizontal area displayed by the projector. Press the POINT LEFT/RIGHT button to decrease/increase value
to match the resolution of image.
Display area V
Adjustment of vertical area displayed by the projector. Press the POINT LEFT/RIGHT button to decrease/increase value to
match the resolution of image.
Full screen
When this function is on, SXGA image is fully displayed at 4 : 3 aspect ratio. It is displayed at 5 : 4 aspect ratio with this
function off.
NOTE : The Full screen cannot be selected after the Display area, Display area H, and Display area V are adjusted.
Reset
Reset all adjustment to their previous level. (The Reset does not work for the stored data.)
Mode free
To clear the adjustment parameters previously set, select Mode free and press the POINT RIGHT button. Choose the mode
that you want to clear, and then press the SELECT button.
Store
To store the adjustment parameters, select Store and press the POINT RIGHT button. Choose one of the Mode 1 to 5, and
press the SELECT button.
Quit
Close the Computer Adjustment menu.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Image Level Selection (Direct Operation)
Select the image level from Standard, Real, Image 1, Image 2, Image
3, and Image 4 by pressing the IMAGE button on the remote control.
(See the next section "Image Level Selection (Menu Operation)" about
each item.)
IMAGE button
Standard
IMAGE button
Real
INPUT
IMAGE
IMAGE
Image 1
Image 2
Image 3
Image 4
VIDEO
NO SHOW
AUTO
1
2
3
4
VIDEO
KEYSTONE
S-VIDEO
COMPONENT
COMPO
IMAGE 1-4 button
Image Level Selection (Menu Operation)
Press the MENU button, and the main menu appears. Select
Image Level Selection menu
the Image Level Selection menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Image Level Selection menu
The level being selected
Choose the level that you want to set with the POINT UP/DOWN
button, and then press the SELECT button to activate it.
Standard
Normal picture adjustment preset on this projector.
Real
Picture adjustment improved in reproduction of halftones. This
adjustment is suitable for providing better image in brighter place.
IMAGE 1~4
User preset picture adjustment in the Image Level Adjustment menu
(p39, 40).
Close the Image Level Selection menu.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Image Level Adjustment
Press the MENU button, and the main menu appears. Select
Image Level Adjustment menu
the Image Level Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
1
2
Image Level Adjustment
menu
Choose the item that you want to adjust with the POINT
UP/DOWN button, and then press the POINT LEFT/RIGHT
button to adjust each item. The items displayed in a line can be
adjusted while you see the change of the image. Press the
SELECT button to finish adjusting an item. The on-screen menu
returns to the sub-menu.
Press the
SELECT button
at this icon to
display other
items.
Press the SELECT button at this
icon to close the item.
To store the adjustment data, select the Store with the POINT
UP/DOWN button and press the POINT RIGHT button.
3
4
Reset
To reset to previous level, select the Reset with the POINT
UP/DOWN button and press the POINT RIGHT button. Select
"Yes" with the SELECT button.
Select the Store.
Choose one of the positions from the Image Level 1 to 4 where
you want to store with the POINT UP/DOWN button, and press
the SELECT button. Select "Yes" with the SELECT button and
close the menu by pressing the SELECT button at the Quit.
NOTE
All the items on the next page can be memorized in Image 1-4.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
The items that you can adjust are the following:
Contrast
Press the POINT LEFT button to decrease contrast and the POINT RIGHT button to increase contrast. (From 0 to 63.)
Brightness
Press the POINT LEFT button to adjust image darker and the POINT RIGHT button to adjust image brighter. (From 0 to 63.)
Color temp.
Press the POINT LEFT button or the POINT RIGHT button for Color temp. level that you want to select. (XLow, Low, Mid, or
High)
White balance (Red)
Press the POINT LEFT button to lighten red tone and the POINT RIGHT button to deepen red tone. (From 0 to 63.)
White balance (Green)
Press the POINT LEFT button to lighten green tone and the POINT RIGHT button to deepen green tone. (From 0 to 63.)
White balance (Blue)
Press the POINT LEFT button to lighten blue tone and the POINT RIGHT button to deepen blue tone. (From 0 to 63.)
Sharpness
Press the POINT LEFT button to soften the image and the POINT RIGHT button to sharpen the image. (From 0 to 15.)
Gamma
Press the POINT LEFT button or the POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)
Auto grayscale
When this function is "ON", it automatically enhances contrast of bright and dark part of image.
Auto fleshtone
When this function is "ON", it produces more vivid image according to image condition.
Reset
Reset all adjustment to their previous levels. (The Reset does not work for the stored data.)
Store
Store the adjustment data.
Quit
Close the Image Level Adjustment menu.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Screen Size Adjustment (Direct Operation)
Select the screen size from Normal, Full, True, and D.Zoom by
pressing the SCREEN button on the remote control. (See the next
section "Screen Size Adjustment (Menu Operation)" about each item.)
SCREEN button
Normal
SCREEN button
AUTO PC ADJ.
LIGHT
AUTO
Full
MENU
SCREEN
True
SELECT
D.Zoom
Screen Size Adjustment (Menu Operation)
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press the MENU button, and the main menu appears. Select
the Screen Size Adjustment menu with the POINT UP/DOWN
button, and then press the POINT RIGHT button to enter the
sub-menu.
Screen Size Adjustment menu
1
Screen Size Adjustment menu
Press the
Choose the item that you want to set, and then press the
SELECT button to activate it.
SELECT button
at this icon to
activate the
item.
2
Normal
Provides an image at the normal video aspect ratio of 4 : 3.
Full
Provides an image to fit the horizontal size of the screen.
True
Provides image in its original size. When the original image size is larger than screen size (964 X 544), this projector enters
"Digital zoom" automatically.
Digital zoom
When Digital zoom is selected, the on-screen menu disappears and the message “D.Zoom” is displayed. Press the SELECT
button to expand the image. And press the POINT UP/DOWN/LEFT/RIGHT button(s) to pan the image. The panning
function can work only when the original image is larger than screen size (964 X 544).
NOTE
The Screen Size Adjustment menu cannot be operated when “1035i (HDTV)”, “1080i (HDTV)”, or "720p(HDTV)" is selected
in the Computer System menu (p32).
The True and Digital zoom cannot be selected when "RGB" is selected in the Computer System menu (p32).
Panning function may not operate properly if the computer system (Mode 1-5) stored in the Computer Adjustment menu is
used.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Setting
Press the MENU button, and the main menu appears. Select
the Setting menu with the POINT UP/DOWN button, and then
press the POINT RIGHT button to enter the sub-menu.
Setting menu
1
Setting menu
Choose the item that you want to set with the POINT UP/DOWN
button, and then press the POINT LEFT/RIGHT button for each
setting.
2
Close the Setting menu.
The items that you can adjust are the following:
Language
When pressing the
SELECT button at the
Language, the Language
menu appears.
Language is selectable from English, German, French, Italian,
Spanish, Portuguese, Dutch, Swedish, Russian, Chinese, Korean, and
Japanese.
Keystone
When the image is distorted vertically, select the Keystone. The on-
screen menu disappears and the Keystone dialog box is displayed.
Correct keystone distortion by pressing the POINT UP/DOWN button.
Refer to Keystone Adjustment on page 21.
Blue back
When this function is “On,” the projector displays a blue image while input signal is not detected.
Menu position
Display
This function decides whether to display On-Screen Displays.
On ··· shows all the On-Screen Displays.
Off ···· sets On-Screen Displays disappeared except;
G ON-SCREEN MENU
G “Power off?” message
G “No signal” message
G “Wait a moment!" message
Menu position
This function is used to change the position of the on-screen menu.
Move the position of the on-screen menu with the POINT
buttons.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Logo
Ceiling function
Rear function
When this function is “On,” the projector displays our logo when starting
up.
Ceiling
When this function is “On,” picture is top / bottom and left / right
reversed. This function is used to project the image from a ceiling
mounted projector.
Rear
When this function is “On,” picture is left / right reversed. This function
is used to project the image to a rear projection screen.
Power management
Time left until the lamp
goes off.
This function turns the Projection lamp off when this projector detects
signal interruption and is not used for a certain period in order to
reduce power consumption and maintain the lamp lifetime. (This
projector is shipped with this function ON.) This function operates as
follows;
1. When any input signal is interrupted or no button is pressed for about 30 seconds, “No signal” and the counting down
display appears (for 5 minutes).
2. After counting down for 5 minutes, the Projection lamp and the READY indicator are turned off. (Cooling Fans keep
running.)
3. The READY indicator starts to flash after cooling down the Projection lamp for about 90 seconds (Power management
mode). In this Power management mode, the Projection lamp is automatically turned on when the input signal is
connected or the projector is operated with any button on the top control or on the remote control again.
Power off confirmation
The confirmation dialog box to turn off the projector is displayed with this function ON.
Lamp mode
"
"
"
"
, the projector turns to the
When selecting the
, the projector operates with full brightness. When selecting the
Theater black mode that lowers the screen brightness, saves electricity, and extend the lamp life. The projector also
operates silently.
Remote control
This projector has two different remote control codes: Code 1 and Code 2 (initial code) This switching function prevents
remote control interference when operating several projectors or video equipment together.
When operating the projector in “Code 1,” both the projector and remote control must be switched to “Code 1.”
To change the code of the Projector;
Set the remote control in the Setting menu to “Code 1.”
To change the code of the Remote Control;
Press both the MENU and the IMAGE buttons on the remote control together for over 10 seconds.
After changing the code, make sure the remote control operates properly.
To return to the initial code (Code 2), repeat the steps above.
NOTE : When the batteries of the remote control are replaced, the remote control code automatically returns to the initial
code (Code 2).
Lamp counter reset
This function is used to reset the Lamp Replace Counter. When replacing the Projection lamp, reset the Lamp Replace
Counter by using this function. Refer to page 45 for operation.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Lamp Replacement
When the life of the projection lamp draws to an end, the LAMP
REPLACE indicator lights yellow. When this indicator lights yellow,
replace the projection lamp with a new one promptly.
TOP CONTROL
WARNING
TEMP.
RE
This indicator lights yellow
when the life of the projection
lamp draws to an end.
Replace the Projection Lamp
with a new one.
LAMP
REPLACE
ON-OFF
CAUTION
FOR CONTINUED SAFETY, REPLACE WITH A LAMP
ASSEMBLY OF THE SAME TYPE.
ALLOW A PROJECTOR TO COOL, FOR AT LEAST 45
MINUTES BEFORE YOU OPEN LAMP COVER. THE
INSIDE OF A PROJECTOR CAN BECOME VERY
HOT.
DO NOT DROP A LAMP ASSEMBLY OR TOUCH A
GLASS BULB! THE GLASS CAN SHATTER AND MAY
CAUSE INJURY.
Follow these steps to replace the lamp assembly.
SCREW
Turn off the projector and disconnect AC plug. Allow the
projector to be cooled for at least 45 minutes.
1
2
3
4
LAMP COVER
To remove the Lamp cover, remove the screw with a
screwdriver.
Remove 2 screws with a screwdriver and pull out the Lamp
assembly by grasping the handle.
Replace the Lamp assembly with a new one and tighten the 2
screws back into position. Make sure that the Lamp assembly is
set properly. Replace the Lamp cover and tighten the screw.
HANDLE
Connect the AC Power Cord to the projector and turn on the
projector.
LAMP
ASSEMBLY
SCREW
5
6
Reset the Lamp Replace Counter.
Refer to “Lamp Replace Counter” on the next page .
SCREW
NOTE : Do not reset the Lamp Replace Counter when the
Projection lamp is not replaced.
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through Boxlight at 1-800-762-5757 or 360-779-7901.
G Model No. of your projector
G Replacement Lamp Type No.
:
:
Matinee 1HD
POA-LMP54
(Service Parts No. 610 302 5933)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Lamp Replace Counter
Be sure to reset the Lamp Replace Counter after the Lamp assembly is replaced. After the Lamp Replace Counter is reset,
the LAMP REPLACE indicator stops lighting.
Turn on the projector and press the MENU button. The main
menu appears. Select the Setting menu with the POINT
UP/DOWN button, and then press the POINT RIGHT button
to enter the sub-menu.
Setting menu
1
Choose the Lamp counter reset with the POINT UP/DOWN
button, and then press the SELECT button.
2
3
The message “Lamp replace counter reset?” is displayed.
Select "Yes" with the SELECT button, and the other
confirmation display appears. Select "Yes" with the SELECT
button to reset.
The LAMP REPLACE indicator stops lighting after the Lamp
Replace Counter is reset.
Select "Yes" to reset.
NOTE : Do not reset the Lamp Replace Counter before the Projection lamp is replaced.
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
G Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
G If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
( Follow carefully the instructions in the Lamp Replacement section of this manual. ) Continuous use
of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.
G A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Warning Temp. Indicator
The WARNING TEMP. indicator flashes red when an internal temperature of the projector exceeds the normal temperature.
The indicator stops flashing when the temperature of the projector returns to normal.
When the WARNING TEMP. indicator continues to flash, check the items listed below.
Ventilation slots of the projector may be blocked. In such an
event, reposition the projector so that the Ventilation slots cannot
be obstructed.
TOP CONTROL
1
2
WARNING
TEMP.
RE
The Air filter may be clogged with dust particles. Clean the Air
filter by following the section "Air Filter Care and Cleaning"
below.
LAMP
REPLACE
Warning Temp.
indicator
ON-OFF
If the WARNING TEMP. indicator remains on after performing
the above checks, the Cooling fans or the internal circuits may
be malfunctioning. Contact service personnel from an
authorized dealer or a service station.
3
Air Filter Care and Cleaning
The removable Air filter prevents dust from accumulating on the surface of the projection lens and projection mirror. Should
the Air filter become clogged with dust particles, it will reduce the cooling fans’ effectiveness and may result in internal heat
build up and adversely affect the life of the projector. Clean the Air filter by following the steps below.
Turn off the projector, and disconnect AC Power Cord from the
AC outlet.
1
LATCH
Turn over the projector and remove the Air filter by pulling the
latch upward.
2
Clean the Air filter with a brush or wash out dust and particles.
AIR FILTER
3
Replace the Air filter properly. Make sure that it is fully inserted.
4
AIR INTAKE VANTS
Clean the Air intake vents with a vacuum cleaner at the same time.
CAUTION
Do not operate the projector with the Air filter removed.
Dust may accumulate on the LCD panels and the projection
mirror degrading picture quality.
Do not put small parts into the Air intake vents. It may result
in malfunction of the projector.
Operating Environment
We recommend avoiding dusty/smoky environments when operating a projector.
When using under dusty or smoky conditions, dust may accumulate on the lens, liquid crystal panels, or optical elements
inside the projector. This condition may degrade the quality of a projected image and the life of the projector.
When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
Cleaning the Projection Lens
Follow these steps to clean the projection lens.
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.
1
Lightly wipe the Projection lens with a cleaning cloth.
2
When the projector is not in use, close the front cover.
3
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the following:
• Make sure you have connected the projector to video equipment or your computer as described on page 17 and 18.
• Check cable connection. Verify that all video, computer, and power cord are properly connected.
• Verify that all power is switched on.
• When you are operating the projector with a computer and it does not produce an image, restart the computer.
• Select the other input source.
Problem:
No power.
Try these Solutions
G Plug the projector into your AC outlet.
G Make sure the MAIN ON/OFF switch is ON and that the READY indicator lights green.
G Open the front cover.
G Wait 90 seconds after the projector is turned OFF when turning the projector back on.
NOTE : After pressing the POWER ON-OFF button to OFF, make sure the projector works
as follows:
1. The LAMP indicator lights bright and the READY indicator turns off.
2. After 90 seconds, the READY indicator lights green again and the projector can
be turned on by pressing the POWER ON-OFF button.
G Check the WARNING TEMP. indicator. If the indicator flashes red, the projector cannot
be turned on.
(See the NOTE on page 19.)
G Check the projection lamp. (Refer to page 44.)
G Adjust focus of the projector.
G Make sure the projection screen is at least 3.6’ (1.1m) from the projector.
G Check the projection lens to see if it needs cleaning.
Image is out of
focus.
NOTE : Moving the projector from a cool temperature location to a warm temperature
location may result in moisture condensation on the Projection Lens. In such an
event, leave the projector OFF and wait until condensation disappears.
G Check Ceiling / Rear function. (See the Setting section on page 43.)
Picture is Left/Right
reversed.
G Check Ceiling function. (See the Setting section on page 43.)
Picture is
Top/Bottom
reversed.
G Check Display function.(See the Setting section on page 42.)
Some displays are
not seen during the
Operation.
G Check the connection between video equipment / your computer and the projector.
G Check the input source is selected properly.
No image.
G Check NO SHOW function. (Refer to page 21.)
G When turning the projector on, it takes about 30 seconds to display an image.
G Check the system that you select is corresponding with video equipment or your
computer.
G Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).
G Check the batteries.
Remote Control does
not work.
G Make sure there is nothing between the Infrared Remote Receiver and remote control.
G Make sure you are not too far from the projector when using the remote control.
Maximum operating range is 16.4’ (5m).
G Make sure the code of the remote control is set to conform to the projector.
(See the Setting section on page 43.)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Indicators and Projector Condition
Check the Indicators for projector condition.
Indicator
Projector Condition
The projector is OFF.
LAMP
Red Light
Dim Light
The projector is ON.
The MAIN ON/OFF switch is off or AC Power Cord is disconnected.
The projector is READY to be turned on.
The projector is in the Power management mode.
Off
READY
Green Light
Green Flashing
Off
The projector is OFF. (The MAIN ON/OFF switch is off, AC Power
Cord is disconnected, or the front cover is closed.)
The temperature inside the projector is abnormally high. The
Flashing stops when the temperature returns to normal. The
projector cannot be turned on until this indicator goes off.
WARNING TEMP.
(page 46)
Red Flashing
The projector is operating normally.
The projection lamp needs to be replaced.
The projector is operating normally.
Off
LAMP REPLACE
(page 44)
Yellow Light
Off
after following all operating instructions,
If the problem still persists
contact the dealer where you purchased the projector or
Give the model number and explain the difficulty. We will advise you how to obtain service.
the service center.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical Specifications
Multi-media Projector
Projector Type
13.11" x 4.27" x 9.70" (333mm x 108.5mm x 246.5mm) (not including Adjustable Feet)
7.5lbs (3.4 kg)
(W x H x D)
Dimensions
Net Weight
0.7" Wide TFT Active Matrix type, 3 panels
964 x 544 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
High Definition TV Signal
Scanning Frequency
Projection Image size
Projection Lens
Throw Distance
1,573,248 (964 x 544 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
H-sync. 15 ~ 80 KHz, V-sync. 50 ~ 100 Hz
Adjustable from 30” to 200”
(Diagonal)
F 2.03 ~ 2.34 lens with f 21.2 mm ~ 25.4 mm with manual zoom and focus
3.6’ ~ 19.7’ (1.1 m ~ 6.0 m)
130 W
Projection Lamp
RCA Type x 4 (Video, Y, Pb/Cb, Pr/Cr) and Mini DIN 4 pin x 1 (S-Video)
(VGA) HDB 15 Terminal x 1
Video Input Jacks
Computer Input Terminal
0˚ to 11.8˚
Feet Adjustment
Voltage and
AC 100 ~ 120 V (2.4 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (1.2 A Max. Ampere), 50 / 60 Hz (Continental Europe
)
Power Consumption
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
Operating Temperature
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Storage Temperature
Remote Control
Power Source
Operating Range
Dimensions
:
:
:
:
AA, UM3 or R06 Type x 2
16.4’ (5m) / 30˚
1.85” x 1.18” x 6.26” (47mm x 30mm x 159mm)
4.4oz (125g) (including batteries)
Net Weight
Owner’s Manual
AC Power Cord
Accessories
Remote Control and Batteries
Video Cable
G The specifications are subject to change without notice.
G LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a
tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards
against risk of fire, casualty and electrical hazards.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Dimensions
Unit : inch (mm)
13.11 (333)
11.8˚ (Max.)
WARNING
READY
TEMP.
LAMP
REPLACE
LAMP
ON-OFF
9.70 (246.5)
MENU
INPUT
SELECT
4.27 (108.5)
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Configuration of Terminals
COMPUTER INPUT TERMINAL (ANALOG)
Terminal : HDB15-PIN
1
2
3
4
5
6
7
8
Red Input
Green Input
Blue Input
Sense 2
9
No Connect
Pin Configuration
10 Ground (Vert.sync.)
11 Sense 0
12 Sense 1
2
1
5
4
3
10
9
8
7
6
15
14
13
12
11
Ground (Horiz.sync.) 13 Horiz. sync.
Ground (Red)
Ground (Green)
Ground (Blue)
14 Vert. sync.
15 Reserved
SERVICE PORT CONNECTOR
Terminal : Mini DIN 8-PIN
*This port is only used for service.
Serial
R X D
-----
Pin Configuration
1
2
3
4
5
6
7
8
-----
8
7
6
GND
5
4
3
RTS / CTS
T X D
GND
2
1
GND
Optional Parts
The parts listed below are optionally supplied. When ordering those parts, give name and Type No. of it to the sales dealer.
GMAC Adapter
Type No. : POA-MACAP
GSCART-VGA Cable
Type No. : POA-CA-SCART
(This cable is used for RGB Scart 21-pin output of video
equipment.)
51
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
BOXLIGHT Corporation (“BOXLIGHT”) warrants that each Matinee 1HD (“the Product”) sold hereunder will conform to and
function in accordance with the written specifications of BOXLIGHT. Said limited warranty shall apply only to the first
person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale.
Said warranty shall continue for a period of three (3) years from the date of such purchase. The standard limited warranty
excludes the lamps in projectors after 120 days and the accessories after one year. BOXLIGHT does not warrant that the
Product will meet the specific requirements of the first person or entity that purchases the Product for personal or business
use. BOXLIGHT’s liability for the breach of the foregoing limited warranty is limited to the repair or replacement of the
Product or refund of the purchase price of the Product, at BOXLIGHT’s sole option. Replacement Product may be re-
furbished in “like-new” condition, at BOXLIGHT’s sole discretion. To exercise the Purchaser’s rights under the foregoing
warranty, the Product must be returned at the Purchaser’s sole cost and expense, to BOXLIGHT or to any authorized
BOXLIGHT service center provided, and the Product must be accompanied by a written letter explaining the problem and
which includes (i) proof of date of purchase; (ii) the dealer’s name; and (iii) the model and serial number of the Product.
When sending your unit in for repair, please ship your unit in its original packing material or a BOXLIGHT approved ATA
Shipping Case, or have a professional packaging company pack the unit. Please insure your shipment for its full value.
A return authorization number, issued by the BOXLIGHT customer service department, must also be clearly
displayed on the outside of the shipping carton containing the Product.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to
abuse, misuse, neglect, accident, unusual physical or electrical stress (unusual physical and electrical stress includes
unusually long operation, exposure to smoke and other airborne contaminants), unauthorized modifications, tampering,
alterations,
or service other than by BOXLIGHT or its authorized agents, causes other than from ordinary use or failure to properly use
the Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO
WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE
EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY BOXLIGHT. SOME STATES DO
NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT
APPLY TO YOU.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT’S LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY
WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE
PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL BOXLIGHT BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR
LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING BOXLIGHT’S
LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE
PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS
ACCRUED. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS
LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT
VARY FROM STATE TO STATE.
Boxlight
19332 Powder Hill Place
Poulsbo, WA 98370-7407 USA
U.S. and Canada 800-762-5757
International 1-360-779-7901
Printed in Japan
Part No. 610 304 4927 (1AA6P1P3782-- M4JE)
Download from Www.Somanuals.com. All Manuals Search And Download.
|