User guide
Z320i
Prepare the phone
Always turn off your phone and detach the charger before you
insert or remove the SIM card.
To insert the SIM card and battery
1
2
3
4
Remove the battery cover by sliding the battery release
latch down.
Slide the SIM card into its holder with the contacts facing
down.
Insert the battery with the label side up and the connectors
facing each other.
Slide the battery cover into place and close the battery release
latch.
3
This is the Internet version of the user's guide. © Print only for private use.
Charge the battery
Your phone battery is partly charged when you buy it.
It takes approximately 3 hours to fully charge the battery.
It may take 30 minutes for the battery icon to appear on
the screen.
To charge the battery
1
2
Connect the charger to the phone. Press a key to view the
charging status on the screen.
To remove the charger, tilt the plug upwards.
You can use the phone during charging. You can charge
the battery for more or less than 3 hours. Interrupted
charging will not damage the battery.
4
This is the Internet version of the user's guide. © Print only for private use.
Turn the phone on
To turn on the phone
1
2
Press and hold down
.
Enter your PIN if requested. To
correct mistakes, press
Select OK.
Select a language.
At first start-up, select Yes
.
3
4
5
to use the setup wizard to make a phone setup. Select No
to use the setup wizard later.
After you have turned the phone on and entered
your PIN, the name of your operator appears on the
screen. This view or screen is called standby. You can
now make and receive calls.
To turn off the phone
Press and hold down
•
.
To use the setup wizard
•
From standby select Menu > Settings > General >
Setup wizard > Basic setup.
5
This is the Internet version of the user's guide. © Print only for private use.
SIM card
The SIM (Subscriber Identity Module) card, which you
get from your network operator, contains information
about your subscription. Always turn off your phone
and detach the charger before you insert or remove
the SIM card.
You can save contacts on the SIM card before removing
if from your phone. Contacts may also be saved in the
phone memory. See Contacts on page 16.
PIN code (SIM card lock)
The PIN (Personal Identification Number) code is a SIM card
lock that protects your subscription, but not the phone itself.
If the card is locked, you have to enter the PIN code when you
turn on your phone. Each PIN digit appears as *, unless it
starts with emergency number digits, for example, 112 or 911.
You can call an emergency number without entering a PIN.
If you enter the wrong PIN three times in a row, the
following message appears: PIN blocked. To unblock,
enter your PUK code provided by your network
operator. To unblock your SIM card, see Locks on
page 35
6
This is the Internet version of the user's guide. © Print only for private use.
Menu overview
Calls
Internet
Games
Camera
Messaging
File manager
Write new
Inbox
Camera album
Pictures
Call voicemail
Drafts
Outbox
Sent messages
Saved messages
Templates
Settings
Ringtones
Themes
Bookmarks
Games
Applications
Other
Organizer
Contacts
Settings
Online services
Alarm
Options
New contact
General
Sounds & alerts
Applications
Calendar
Tasks
Display
Calls
Connectivity
Notes
Calculator
Timer
Stopwatch
Some menus and icons described in this document may vary
depending on operator, network or subscription. Some options
may vary when the default settings are changed.
7
This is the Internet version of the user's guide. © Print only for private use.
Phone overview
Network
coverage
Battery status
Function for
left selection
key
Function for
right selection
key
Calls
Menu
Internet key
Navigation key
Left selection
key
Right selection
key
Camera key
Back key
Volume
buttons
C key (Clear)
On/off key
Charging
(USB
connector)
Infrared port
Microphone
8
This is the Internet version of the user's guide. © Print only for private use.
Network coverage
The network bars show the strength of the GSM network.
Move to another location if you have network problems. No
netw. coverage means you are out of range.
= Good network coverage
= Average network coverage
Battery status
= The phone battery is fully charged
= The phone battery is empty
The outside
Camera lens
Icon display
9
This is the Internet version of the user's guide. © Print only for private use.
Icons
These icons may appear in your phone.
Icon Description
Battery charging, appears with battery icon.
You have missed a call. See Calling on page 14.
The phone is set to silent.
You have received a new text message.
You have received a new picture message.
Ongoing call.
Divert calls is activated.
An alarm is activated.
The loudspeaker is on.
The infrared port is activated.
The stopwatch is activated.
10
This is the Internet version of the user's guide. © Print only for private use.
Shortcuts
From standby you can use the navigation keys to go directly
to a function:
•
•
•
Press
Press
Press
to start the camera.
to write a message.
to go to your contacts.
To change a standby shortcut, go to Menu > Settings >
General > Shortcuts. The camera shortcut cannot be
changed.
To navigate the menus
•
•
•
•
From standby select Menu and
press
Press
,
,
or
.
to go back one step
in the menu.
Press and hold down
standby.
to return to
Press
or
to move between tabs.
To delete items
Press
•
.
To set the phone to silent
Press and hold down
•
to set silent mode on or off.
To view tips and tricks
•
From standby select Menu > Settings > General >
Setup wizard > Tips and tricks.
11
This is the Internet version of the user's guide. © Print only for private use.
Messaging
Your phone supports various messaging services.
See Entering text on page 26 for instructions on how to
enter text and numbers.
Text messages
You need a service centre number from your network
operator to be able to send text messages.
To view and set the service centre number
1
From standby select Menu > Messaging > Settings >
Text message > Service centre.
If there is no number, select New ServiceCentre, enter
the number including the international “+” prefix and
country/region code. Select Save.
2
To write and send a text message
1
From standby select Menu > Messaging > Write new >
Text message.
2
3
4
Write the message and select Continue.
Select Enter phone no., enter the number and select OK.
Select Send.
Picture messages
Picture messages can contain enhanced functionality
with text, sound and pictures.
You need the correct Internet (MMS) settings in your
phone. Go to www.sonyericsson.com/support and
request a text message with the settings or contact your
network operator.
To create and send a picture message
1
From standby select Menu > Messaging > Write new >
Picture msg.
2
3
Select More and select an item to follow your message.
Write the message and select OK > Continue.
12
This is the Internet version of the user's guide. © Print only for private use.
4
5
Select Enter phone no., enter the number and select OK.
Select Send.
To save an item in a picture message
1
2
In the message, select More > Save items.
Select an item and where to save it.
To delete all sent messages
1
2
From standby select Menu > Messaging > Sent messages.
Select More > Delete all msgs > Yes.
Automatic download
Select how to download your picture messages.
To select a download option
1
From standby select Menu > Messaging > Settings >
Picture message > Auto download.
Select an option:
Always – automatic download.
Ask in roaming – ask to download when not in home
network.
Not in roaming – do not download when not in home
network.
Always ask – ask to download.
Off – new messages appear in the inbox as icons. Select
the message and select View to download.
2
•
•
•
•
•
Receiving messages
To view and save a message from the inbox
1
2
From standby select Menu > Messaging > Inbox.
Scroll to a message and select View. If you want to save
the message, select More > Save message > Saved
messages (SIM card) or > Templates (phone).
To delete messages from the inbox
1
2
From standby select Menu > Messaging > Inbox.
Select More > Delete all msgs > All > Yes to delete all
messages. To delete one message, scroll to the message
and select More > Delete > Yes.
13
This is the Internet version of the user's guide. © Print only for private use.
Calling
Your phone must be on and within range of a network.
To make a call
1
2
From standby enter the area code and phone number.
Select Call.
To make an emergency call
•
From standby enter 112 (the international emergency
number) and select Call.
You can make emergency calls without a SIM card and
without entering a PIN.
To make an international call
1
2
From standby press
Enter the country/region code, area code (without the first
zero), phone number and select Call.
until a + sign appears.
To end a call
Close the phone or select End call.
•
To answer a call
When the phone rings, select Answer.
•
To reject a call
When the phone rings, select Busy.
•
To view missed calls
•
When Missed calls: is displayed, select Yes. To call
back, scroll to a number and select Call.
14
This is the Internet version of the user's guide. © Print only for private use.
To turn the loudspeaker on during a call
•
Select More > Turn on speaker.
Do not hold the phone to your ear when using the
loudspeaker. This could damage your hearing.
To change the ear speaker volume during a call
Press or
•
.
To turn off the microphone during a call
Press and hold down . To resume, press and hold
down again.
•
Call list
You can view information about recent calls.
To call a number from the call list
1
2
From standby select Calls and scroll to a tab.
Scroll to the name or number and select Call.
To add a number to contacts
1
2
3
4
From standby select Calls and scroll to a tab.
Scroll to the number and select More > Save number.
Select a contact or select New contact.
Enter the contact information and select Save.
To delete a number from the call list
1
2
From standby select Calls and scroll to a tab.
Scroll to the number and select More > Delete entry
> Yes.
15
This is the Internet version of the user's guide. © Print only for private use.
Contacts
In Contacts you can save contact information with name,
numbers, addresses, picture, ringtone, title, personal information
and birthday.
See Entering text on page 26 for instructions on how to
enter text and numbers.
To add a contact
1
2
3
4
5
6
7
From standby select Menu > Contacts.
Scroll to and select New contact > Add.
Enter the name and select OK.
Scroll to New number: and select Add.
Enter the number and select OK.
Scroll to and select the contact type.
Select Save.
Enter the + sign and country/region code with all phone
numbers. They can then be used abroad or at home.
To call a phone contact
When Chinese has been selected as the phone language
To call a contact written in Chinese characters
1
> Contacts. Press and hold
to switch the search
language to Chinese. Then enter the first strokes or all
strokes of the contact you want to call (a maximum of
10 strokes).
2
When the contact is highlighted, press
a number > Call.
or
to select
To call a contact written in Latin characters
1
> Contacts. Press and hold
to switch the search
language to English. Then enter the first letters or all letters
of the contact you want to call (a maximum of 10 letters).
2
When the contact is highlighted, press
a number > Call.
or
to select
16
This is the Internet version of the user's guide. © Print only for private use.
When English has been selected as the phone language
To call a contact written in Chinese characters
1
2
> Contacts. Scroll to the contact you want to call.
When the contact is highlighted, press
or
to select
a number > Call.
To call a contact written in Latin characters
1
> Contacts. Scroll to, or enter the first letters or all letters
of the contact you want to call (a maximum of 10 letters).
2
When the contact is highlighted, press
a number > Call.
or
to select
To delete a contact
1
2
From standby select Menu > Contacts.
Scroll to the contact and press
.
To edit a contact
1
2
3
4
5
From standby select Menu > Contacts.
Scroll to the contact and select More > Edit contact.
Scroll to the contact information and select Edit.
Enter information or select a picture or ringtone.
Confirm and select Save.
To send all contacts
•
From standby select Menu > Contacts > Options >
Advanced > Send all contacts and select a transfer
method.
To copy contacts between the phone and the SIM card
1
From standby select Menu > Contacts > Options >
Advanced.
2
3
Select Copy to SIM or Copy from SIM.
Select Copy a number or Copy all.
17
This is the Internet version of the user's guide. © Print only for private use.
4
To copy one contact, select the contact.
When copying all contacts to the SIM card, all existing SIM
card information is replaced.
To check memory status for your contacts
•
From standby select Menu > Contacts > Options >
Advanced > Memory status.
Speed dialling
Speed dialling lets you select nine contacts that you can dial
quickly by pressing numbers 1-9.
To add contacts to speed dial numbers
1
From standby select Menu > Contacts > Options >
Speed dial.
Scroll to a position number and select Add.
Select a contact.
2
3
To speed dial
From standby enter the number (1-9) and select Call.
•
My number
You can view and edit your own phone number.
To view your own phone number
•
From standby select Menu > Contacts > Options >
Special numbers > My numbers.
18
This is the Internet version of the user's guide. © Print only for private use.
Camera
Your phone has a digital camera to take pictures to save or
send. Use infrared or picture messages to send a picture to
another phone or to a computer. Camera pictures are saved
in JPEG format in the Camera album.
To take pictures
1
2
3
From standby press
to start the camera.
Select Capture to take the picture.
Press
to save and take another picture or select More >
Delete to delete the picture.
To use the zoom
Use or to zoom.
•
To adjust the brightness
Use or to adjust the brightness.
•
To use the camera options
1
2
•
•
•
When the camera is activated select More.
Select an option:
Picture size – select between three sizes.
Night mode – enhance picture quality in poor lighting.
Self-timer – the picture is taken a few seconds after you
press Capture.
•
•
•
•
Effects – select different effects for your picture.
White balance – adjust colours to lighting conditions.
Picture quality – select picture quality.
Shutter sound – select different shutter sounds.
19
This is the Internet version of the user's guide. © Print only for private use.
To view your pictures
1
From standby select Menu > File manager > Camera
album.
Scroll to a picture and select View.
2
You can use a USB cable to exchange pictures between
your phone and a computer. For more information go to
To send a picture
1
From standby select Menu > File manager > Camera
album.
2
Scroll to a picture and select More > Send. Select a transfer
method.
To use a picture
1
From standby select Menu > File manager > Camera
album and scroll to a picture.
Select More > Use as and select how to use the picture.
2
See also File manager on page 24 and Infrared on
page 33.
20
This is the Internet version of the user's guide. © Print only for private use.
Style-up™ covers
Some kits may include additional Style-up™ covers.
To change the front cover
1
2
3
4
Insert your thumbnail into the groove on the side.
Gently lift the front cover away from the phone.
Align the cover with the top of the phone.
Snap the cover into place by gently pushing down until it is
lying flat.
To change the battery cover
1
2
Remove the battery cover by sliding the battery release
latch down.
Slide the battery cover into place and close the battery
release latch.
21
This is the Internet version of the user's guide. © Print only for private use.
Internet
You need the correct Internet settings in your phone. If settings
are not in your phone, you can:
•
•
Get them in a text message from the network operator.
request a text message with the settings.
To select an Internet profile
•
From standby select Menu > Settings > Connectivity >
Internet settings > Internet profiles. Select a profile.
To start browsing
1
From standby select Menu > Internet and select a
service.
2
•
Select More for options:
Go to – go to predefined pages or bookmarks, enter a
Web address or show previously visited pages.
Tools – add a bookmark, save a picture, refresh page
content, send a link or make a call when browsing.
View – select full content or text only.
•
•
•
Advanced – select options such as show pictures, allow
cookies, clear cookies, clear cache and Internet status.
To stop browsing
When you browse, select More > Exit browser.
•
22
This is the Internet version of the user's guide. © Print only for private use.
Calendar
You can set and send appointments with reminders.
To add an appointment in the calendar
1
2
3
From standby select Menu > Organizer > Calendar.
Scroll to and select a date. Select New appointm..
Enter the details to confirm the appointment.
To set reminders options
1
From standby select Menu > Organizer > Calendar >
More > Advanced > Reminders.
Select an option. Select Always for a reminder to display
even if the phone is off or in silent mode.
2
To view a calendar week
•
From standby select Menu > Organizer > Calendar >
More > View week.
To send an appointment
1
From standby select Menu > Organizer > Calendar and
select a date.
2
Scroll to an appointment, select More > Send and select
a transfer method.
To find an appointment
1
From standby select Menu > Organizer > Calendar >
More > Advanced > Find.
Enter the search string and select OK.
2
23
This is the Internet version of the user's guide. © Print only for private use.
More functions
File manager
To move a file
1
2
3
From standby select Menu > File manager.
Open a folder, scroll to a file and select More > Move.
Select a folder or select New folder, name the new folder
and select OK.
4
Select Paste.
To select several files
1
From standby select Menu > File manager and open
a folder.
2
3
Scroll to a file and select More > Mark.
Select Mark several or Mark all. To select files, scroll and
select Mark or Unmark.
To view the memory status
•
From standby select Menu > File manager > More >
Memory status.
If the memory is full, delete some content. Scroll to a file
or a folder and select More > Delete.
Profiles
Some phone settings are adapted to different situations, for
example, a meeting.
To select a profile
•
From standby select Menu > Settings > General >
Profiles and select a profile to use.
Alarm
The alarm rings even if the phone is off or set to silent.
To set the alarm
1
From standby select Menu > Organizer > Alarm > Alarm.
24
This is the Internet version of the user's guide. © Print only for private use.
2
Enter the time and select Save.
To turn the sounding alarm off
Press any key. To snooze the alarm, press Snooze.
•
To set the alarm signal
•
From standby select Menu > Organizer > Alarm > Alarm
signal and select a signal.
Tasks and Notes
To add a new task
1
From standby select Menu > Organizer > Tasks > New
task.
Select Task or Phone call. Enter details and confirm each
entry. Select Yes to use the reminder option.
2
To make a note and save it in a list
1
From standby select Menu > Organizer > Notes > New
note.
2
Enter the note and select Save.
Ringtones, sounds and alerts
Your phone has melodies that can be used as ringtones.
To select a ringtone
•
From standby select Menu > Settings > Sounds & alerts
> Ringtone and select a ringtone.
To set the ring volume
1
From standby select Menu > Settings > Sounds & alerts
> Ring volume.
2
Press
or
to set a volume and select Save.
To set the vibrating alert
1
From standby select Menu > Settings > Sounds & alerts
> Vibrating alert.
Select an option.
2
25
This is the Internet version of the user's guide. © Print only for private use.
To set sounds and alerts options
1
2
•
•
•
From standby select Menu > Settings > Sounds & alerts.
Select an option:
Increasing ring – select an increasing ringtone.
Message alert – select message notification.
Key sound – select a key press sound.
Language
To change the phone menu language
•
From standby select Menu > Settings > General >
Language > Phone language and select a language.
Time and date
To set the time and date
1
From standby select Menu > Settings > General > Time
& date.
2
3
Select Time or Date.
Enter the time or date and select Save.
Call time and cost
To check the call time and cost
•
From standby select Menu > Settings > Calls > Time &
cost > Call timers.
Themes
Use themes to change the appearance of the screen.
To set a theme
1
From standby select Menu > Settings > Display >
Themes.
Scroll to a theme and select Set.
2
Entering text
There are two input methods you can use to enter text; multitap
or predictive text input.
26
This is the Internet version of the user's guide. © Print only for private use.
By using predictive text input you only have to press
each key once. Continue writing a word even if it appears
to be wrong. The phone uses the dictionary to recognize
the word when all letters are entered.
To enter text using multitap
•
•
•
Press
Press
Press
–
until the letter appears.
to add a space.
to enter punctuation marks.
Multitap input only applies when latin characters are
selected as input language.
To enter text using predictive text input
•
For example, to write the word “Land”, press
,
,
,
.
•
If the word or punctuation mark is the one you want, press
to accept and add a space. To accept without adding
a space, press
If the word or punctuation mark is not the one you want,
press or to view alternatives.
.
•
To add a word to the dictionary
1
2
When you write, select More > Spell word.
Enter the word using multitap and select Insert.
How to use the keys
•
•
Press and hold down
to change the input method.
Press
to shift between upper case and lower case
letters.
Press and hold down
Press to delete characters. To delete a whole word,
•
•
to change the writing language.
press and hold down
Press and hold down
.
•
–
to enter numbers.
27
This is the Internet version of the user's guide. © Print only for private use.
Chinese input
This mobile phone has different input methods for entering
Chinese characters:
•
•
Stroke input
Pinyin input
You can use these methods, for example, to enter Chinese
names and Chinese short messages.
Switching between Chinese input methods
In the Chinese editing mode, you can select and switch
quickly to another input method by pressing and holding
.
General instructions
Regardless of which input method you choose, your phone
has a function to speed up the entry of Chinese characters.
Whenever you enter a stroke or a Pinyin letter, a candidate
row of the most frequently used characters containing that
stroke or relating to that letter appears at the bottom of the
screen.
If the character you want is not displayed in the candidate
row, press
pressing
to present another candidate row. Continue
until the character you want is displayed.
Alternatively, you can enter the next stroke or Pinyin letter and
a new set of characters will immediately be displayed in the
candidate row. To go back to the previous row, press
. To
select a character in the candidate row, press the navigation
key or press and hold the key corresponding to the number
above the character you want to enter.
Stroke input
A Chinese character is built up of strokes. There are more
than 30 basic strokes, which are grouped into 5 stroke
categories. Each category is represented on the keypad by
one of the keys
-
. The Wild Card key
, is used
when you are not sure of which stroke to use.
28
This is the Internet version of the user's guide. © Print only for private use.
Stroke categories
The 5 stroke categories are defined in the table below:
Number Stroke
Key
Basic Stroke Name Character
Category Stroke
王 十 在 七 天
Over
海 次 找 牡 刁
Lift
中 上 業 門 且
Down
小 水 打 子 承
Down-Hook
直 真 盾 草
Short Slope
Down
八 旭 丹 風 所
Long Left
Slope
香 毛 丘 匕 妥
Over Slope
而 頁 面 貿 殷
Short left
Slope
六 州 心 性 電
Dot
人 火 又 之 木
Right Slope
西 四 酉 酷 酒
Down-
Curved-Over
山 屯 母 互 剝
Down-Over
台 去 公 約 能
Left Slope-
Over
女 好 巡 巢 災
Left Slope-
Dot
衣 以 食 收 瓦
Down-Lift
29
This is the Internet version of the user's guide. © Print only for private use.
Number Stroke
Key
Basic Stroke Name Character
Category Stroke
我 或 民 成 找
Right Slope-
Hook
心 必 思 忘
Down-Over-
Hook
已 也 毛 孔 見
Down-Over-
Curved-Hook
張 號 費 夷 鄂
Down-Over-
Down-Hook
鼎 亞
Down-Over-
Down
寫 字 皮 通 魚
Over-Hook
口 已 戶 書 骨
Over-Down
月 万 同 永 沒
Over-Down-
Hook
又 之 發 多 社
Over-Left
Slope
及 极 廷 建
Over-Down-
Over-Left
Slope
阿 隊 陳 那 部
Over-Left
Slope-
Curved-Hook
乃 奶 盈 鼐
Over-Down-
Over-Hook
30
This is the Internet version of the user's guide. © Print only for private use.
Number Stroke
Key
Basic Stroke Name Character
Category Stroke
凸
Over-Down-
Over-Down
家 狗 豹 逐 逛
Curved-Hook
飛 九 風 氣 迅
Over-Down-
Curved-Hook
投 船 凹 雋
Over-Down-
Over
? (Wild card key)
Components
The basic building units of Chinese characters are
components that are made up of strokes. After entering the
first two strokes of the desired character, the component and
character candidates that started with that stroke are
displayed in the candidate row.
Using components is a fast method for entering complex
characters.
The smaller candidates surrounded by dotted frames are
components, and the bigger candidates without dotted
frames are characters.
For example, to enter “ 信息 ”
1
2
3
Enter “ ”, “ ” and “ ”.
Move the cursor to “ 信 ”, press
Move the cursor to “ 息 ”, press
.
again to select “ 息 ”.
Example of using the wild card key
The wild card key
, is used to supplement unclear strokes
in entering characters. If you want to enter “ 互 ”, but you only
know that “ 一 ” is the first and the last stroke of the character
and that the total number of strokes is four, enter
,
,
,
. The character is displayed in the candidate row.
31
This is the Internet version of the user's guide. © Print only for private use.
Pinyin input
Press the keys containing the required Pinyin letters, and the
phone will make various proposals on the screen, according
to the pronunciation rules of Mandarin.
Below is the key mapping of Pinyin letters on the keypad.
Number Key Pinyin Letter
a b c
d e f
g h i
j k l
m n o
p q r s
t u ü
w x y z
On the keypad, the letter ü is replaced by v.
For example, to enter “ 信息 ”
1
2
Press
When “xin” is highlighted, press
“ 信 ”, then press .(If you want to enter any of the other
suggested Pinyin combinations, scroll up or down to the
desired combination, then press ).
Press again to select “ 息 ”, When “ 息 ” is highlighted.
,
,
.
or
and select
3
Input punctuation, symbols and smilies
Under any Chinese input mode, press
, to see the table
of punctuation marks, symbols and smilies. Use the navigation
key to make a selection. Press
text.
to enter a space into the
32
This is the Internet version of the user's guide. © Print only for private use.
Infrared
Use the infrared port to exchange files such as pictures and
ringtones with other phones or infrared devices.
To turn on infrared
•
From standby select Menu > Settings > Connectivity >
Infrared port > On.
To connect two devices using infrared
1
2
Turn on infrared in both devices.
Make sure the infrared ports are facing each other with
a maximum distance of 20 cm (8”).
To transfer a picture using infrared
1
From standby select Menu > File manager > Camera
album.
2
Scroll to a picture and select More > Send and select Via
infrared.
Diverting calls
Divert calls, for example, to an answering service.
To divert calls
1
From standby select Menu > Settings > Calls > Divert
calls.
2
3
Select a call type, a divert option and select Activate.
Enter the phone number and select OK.
To cancel a call divert
1
From standby select Menu > Settings > Calls > Divert
calls.
2
Select a call type, a divert option and select Deactivate.
Voicemail
Callers can leave a voicemail message when you cannot
answer. You can get your voicemail number from your
network operator.
33
This is the Internet version of the user's guide. © Print only for private use.
To enter your voicemail number
1
From standby select Menu > Messaging > Settings >
Voicemail number.
2
Enter the voicemail number and select OK.
To call your voicemail service
From standby press and hold down
•
.
Multiple calls
When call waiting is activated, you can handle multiple
calls. A short sound indicates a second call.
To activate call waiting
•
From standby select Menu > Settings > Calls > Manage
calls > Call waiting > Activate.
To answer a second call
Select Answer. The ongoing call is put on hold.
•
To reject a second call
Select Busy and continue with the ongoing call.
•
To make a second call
1
2
Select More > Add call. The ongoing call is put on hold.
Enter the number and select Call.
To switch between two calls
Select More > Switch calls.
•
To join two calls
Select More > Join calls.
•
To end calls
1
2
Select End call.
Select No to end both calls or Yes to end one call and
retrieve the call on hold.
34
This is the Internet version of the user's guide. © Print only for private use.
Locks
SIM card lock
To unblock your SIM card, you need to enter your PUK
(Personal Unblocking Key) and PIN code, supplied by
your network operator.
To unblock your SIM card
1
When PIN blocked. To unblock, enter your PUK code
provided by your network operator. is displayed, enter
your PUK and select OK.
2
3
Enter a new four-to-eight-digit PIN and select OK.
Re-enter the new PIN to confirm and select OK.
To turn the SIM card lock on
1
From standby select Menu > Settings > General >
Security > Locks > SIM protection > Protection and
select On.
2
Enter your PIN and select OK.
To edit your PIN
1
From standby select Menu > Settings > General >
Security > Locks > SIM protection > Change PIN.
Enter your PIN and select OK.
Enter a new four-to-eight-digit PIN and select OK.
Re-enter the new PIN and select OK.
2
3
4
35
This is the Internet version of the user's guide. © Print only for private use.
Sony Ericsson Mobile Communications AB
SE-221 88 Lund, Sweden
EN/LZT 108 9547 R2A
Printed in XXX
This is the Internet version of the user's guide. © Print only for private use.
Phone lock
The phone lock protects the phone against unauthorized use.
You can change the phone lock code (0000 by default) to any
four-digit code.
If the phone lock is set to Automatic, you only need to
enter your phone lock code when you insert a different
SIM card.
To set the phone lock
1
From standby select Menu > Settings > General > Security
> Locks > Phone protection > Protection.
2
Scroll to an option, enter your code and select OK.
To edit your phone lock code
1
From standby select Menu > Settings > General > Security
> Locks > Phone protection > Change code.
Enter the current code and select OK.
Enter a new code and select OK.
Re-enter the new code and select OK.
2
3
4
If you forget your new code, you have to take your phone
to your local Sony Ericsson retailer.
To unlock the phone
Enter your code and select OK.
•
37
This is the Internet version of the user's guide. © Print only for private use.
Troubleshooting
You can correct most problems yourself. For more support
information guide or contact your network operator.
Remove the SIM card before handing your phone in for
repair.
The phone turns itself off
Restart the phone or do a master reset.
To restart the phone
1
2
3
Turn the phone off and remove the battery cover.
Remove the battery and put it back in place.
Replace the battery cover and turn the phone on.
To perform a master reset
1
From standby select Menu > Settings > General > Master
reset.
2
Select Reset settings to delete your changes to settings or
Reset all to delete your changes to settings, all contacts,
messages, personal data, and content you have downloaded,
received or edited.
3
Select Continue.
I cannot turn the phone on
•
Attach the charger (make sure the power icon on the charger
is facing upwards) and charge the phone for 3 hours.
38
This is the Internet version of the user's guide. © Print only for private use.
Some menu options appear in grey
A service is not activated or your subscription does not support
the function.
•
Contact your network operator.
The phone is working slowly
•
Delete unwanted content and restart the phone.
No indication of charging
•
The battery is empty or has not been used for a long time.
It may take up to 30 minutes before the battery icon appears
on the screen.
I cannot use Internet or send picture messages
You need a phone subscription that supports data transmission,
and the correct Internet settings.
•
network operator.
What do these error messages mean?
Insert SIM
Your SIM card is not inserted correctly or may be damaged or
dirty. Try one or more of the following:
•
•
Remove the SIM card and insert it correctly.
Clean the connectors on the SIM card and phone with a soft
brush, a cloth or a cotton bud.
•
Check if the SIM card is damaged.
39
This is the Internet version of the user's guide. © Print only for private use.
Insert correct SIM card
•
Check that you are using the correct operator SIM card. If
not, contact your network operator.
Wrong PIN
You have entered your PIN code incorrectly.
•
See Phone lock on page 37.
PIN blocked. To unblock, enter your PUK code provided by
your network operator.
The SIM card is blocked.
•
Unblock. See SIM card lock on page 35
PUK blocked
Contact your network operator.
•
Phone locked
The phone is locked.
•
Unlock. See Phone lock on page 37.
Phone lock code:
The phone lock code is required.
•
Enter the correct code. See Phone lock on page 37.
Codes do not match
Appears when changing a security code.
•
Confirm the new code by entering it twice.
Emerg. calls only
You are within range of a network but are only allowed to use
it for emergency calls.
•
Contact your network operator if the problem persists.
No netw. coverage
There is no network within range.
•
Contact your network operator if the problem persists.
40
This is the Internet version of the user's guide. © Print only for private use.
Declaration of Conformity
We, Sony Ericsson Mobile Communications AB of
Nya Vattentornet
SE-221 88 Lund, Sweden
declare under our sole responsibility that our product
Sony Ericsson type AAB-1022091-BV
and in combination with our accessories, to which this declaration relates
is in conformity with the appropriate standards 3GPP TS 51.010-1, EN
301 489-7 and EN 60950, following the provisions of, Radio Equipment
and Telecommunication Terminal Equipment directive 99/5/EC with
requirements covering EMC directive 89/336/EEC, and Low Voltage
directive 73/23/EEC.
Lund, May 2007
Shoji Nemoto, Head of Product Business Group GSM/UMTS
We fulfil the requirements of the R&TTE Directive (99/5/EC).
41
This is the Internet version of the user's guide. © Print only for private use.
FCC Statement
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Sony Ericsson Z320i
GSM 900/1800/1900
This User guide is published by Sony Ericsson Mobile Communications
AB or its local affiliated company, without any warranty. Improvements
and changes to this User guide necessitated by typographical errors,
inaccuracies of current information, or improvements to programs and/or
equipment, may be made by Sony Ericsson Mobile Communications AB
or its local affiliated company at any time and without notice. Such
changes will, however, be incorporated into new editions of this User
guide. All rights reserved.
© Sony Ericsson Mobile Communications AB, 2007
Publication number: EN/LZT 108 9547 R2A.
Please note: Some of the services in this User guide are not supported
by all networks. This also applies to the GSM International Emergency
Number 112. Please contact your network operator or service provider if
you are in doubt whether you can use a particular service or not. Please
read the Guidelines for safe and efficient use and the Limited warranty
chapters before you use your mobile phone. All illustrations are for
illustration only and may not accurately depict the actual phone.
The Predictive Text Technology is used under license from Zi
Corporation.
Note: Sony Ericsson advised users to backup their personal data information.
All illustrations are for illustration only and may not accurately
depict the actual phone.
42
This is the Internet version of the user's guide. © Print only for private use.
|