Samsung SD 816 User Manual

DVD-ROM DRIVE  
SD-816  
Your DVD-ROM Drive  
Upgrading the Firmware Flash Memory  
Connecting the Cables  
Safety Precautions  
The product firmware can be upgraded by downloading the updated file from the  
following Web site:  
The following diagrams illustrate the precautions to be taken when using  
your DVD-ROM drive.  
1. Power cable  
2. Master/slave select terminal  
System Requirements  
Before you install the DVD-ROM drive, we strongly recommend that you  
check that your setup meets the system requirements listed below.  
3. IDE cable  
4. Audio cable  
Item  
Computer  
Description  
Intel Pentium III (or higher), 350MHz or higher,  
128 MB of RAM (or higher) with an IDE interface  
User's Guide  
1Connecting the power cable  
The 4-pin power cable from the internal power unit of your computer must be  
connected to the power terminal on the rear of the DVD-ROM drive.  
1 2  
3
4 5 6  
Disk space  
100 MB minimum  
1. Connector for stereo headphones with a 3.6 mm stereo mini-jack  
2. Headphone volume control  
3. Disc compartment (the compartment opens and closes automatically  
when you press the Eject button)  
4. Emergency eject hole (if the compartment does not open when you  
press the Eject button, power off the computer, insert a pin or unfolded  
paper clip in the hole and push firmly)  
2Installing a jumper on the master/slave select terminal  
Install the jumper in the correct position on the terminal:  
MA to use the device in the master mode  
SL to use the device in the slave mode  
CS to control the device via a CSEL host interface signal  
Windows version  
Windows 95 OSR2 / 98 / 2000 / ME / XP /  
Windows NT 4.0 (or higher)  
FCC Compliance  
* This product has been set at the UDMA mode. It may cause trouble due to  
the compatibility of a specific board or system. In this case, download the latest  
version of “Firmware” which supports the DMA Mode.  
Changes or modifications not expressly approved by the party responsible for compliance  
could void the user’s authority to operate the equipment  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC rules.  
These limits are designed to provide reasonable protection against harmful  
interference in a residential installation.  
This equipment generates, uses, and can radiate radio frequency energy and,  
if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be  
deter-mined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following measures :  
See Step 3 for further details.  
Using the DMA mode may slightly decrease the efficiency of DVD-ROM.  
You must not use the drive in any manner other than that specified in this guide.  
5. Indicator light (when it is green, a disc is being read)  
6. Eject button  
3
Connecting the IDE cable  
Two configurations are possible.  
Do not attempt to repair the DVD-ROM drive yourself. Contact  
your dealer or local SAMSUNG representative for all repairs.  
If you make any adjustments or perform any operations other  
than those specified in this guide, you run the risk of exposure to  
hazardous radiation.  
CAUTION  
Installing the DVD-ROM Drive  
The DVD-ROM drive is the only IDE device in addition to the hard disk.  
To install your DVD-ROM drive in the PC, proceed as follows.  
Install the jumper in the SL position (Slave).  
Connect the 40-pin flat IDE cable from the IDE port  
1 Make sure that the PC is powered off and disconnected from any power source.  
IDE port  
Avoid exposing your eyes or skin to direct or scattered radiation.  
on the mother board, first to the DVD-ROM drive  
Mother board  
2 If necessary, attach a horizontal bracket to both sides of the drive.  
and then to the hard disk.  
Please refer to the Samsung limited warranty statements.  
WARRANTY  
Precautions  
DVD-ROM Hard disk  
Use of the brackets depends on your computer  
model; you can purchase these accessories  
separately from your computer dealer.  
(SL)  
(MA)  
1. To reduce the risk of fire or electric shock, do not expose this  
appliance to rain or moisture.  
• Re-orient or relocate the receiving antenna.  
You already have an additional IDE device installed in your computer.  
First IDE cable  
Second IDE cable  
• Increase the separation between the equipment and receiver.  
1 2 3  
4
5
2. Always check each disc for cracks before using it. If there are  
cracks on the surfaces, especially around the border of the center  
hole, we recommend that you make a copy of the disc  
immediately and then stop using it. If you continue using the disc,  
it will probably develop more cracks and eventually cause  
irreparable damage.  
Install the jumper in the MA position (Master).  
Connect the 40-pin flat IDE cable from a second  
IDE port on the mother board directly to  
the DVD-ROM drive or first to another additional  
IDE drive and then to the DVD-ROM drive.  
3 Remove the cover from a free expansion slot and  
• Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
1. Two-pin digital audio output terminal for use with a sound or  
MPEG card supporting digital audio features  
2. Four-pin sound output terminal for use with a sound card  
(refer to the sound card documentation for further details)  
3. Master/slave select terminal  
4. 40-pin host IDE interface connector  
5. 4-pin power terminal  
install the DVD-ROM drive, as shown in the illustration.  
Mother  
board  
If you have no free expansion slot,  
install the drive in place of the  
diskette drive.  
• Consult the dealer or an experienced radio/TV technician for help.  
DVD-ROM CD-ROM  
Hard disk  
(MA)  
Hard disk  
(SL)  
(MA)  
(SL)  
3. Do not use poor quality discs:  
COVER  
DVD-ROM  
4Connecting the audio cable from a sound card  
From unknown sources  
Drive  
Connect the 4-pin audio cable between the sound output terminal on the  
DVD-ROM drive and the audio input terminal on the sound card.  
●● Without any copyright  
BG68-00613A Rev.00  
Scratched or damaged in any way  
1
2
3
4
Using the DVD-ROM Drive  
Technical Specifications  
Setting Up the Device Driver  
Installing the Device Driver  
Solving Technical Problems  
SAMSUNG continually strives to improve its products.  
Both the design specifications and these user instructions are thus subject to change without notice.  
To play audio or video CDs in your DVD-ROM drive, proceed as follows.  
No additional device driver is needed for Windows 95/98/2000/ME/XP/NT, as the  
default Windows device driver is used. You can check that the DVD-ROM drive  
has been correctly detected by Windows. To do so, proceed as follows.  
Meaning / Solution  
Problem  
1Push the power button and boot the computer.  
Automatic Setup  
Check that the power, audio and IDE cables are  
SD-816  
The DVD-ROM drive is not  
2After booting the computer, open the disc  
ITEM  
correctly connected to the computer.  
Change the IDE cable and reconnect it to the computer.  
Preferably, connect a second IDE cable to the DVD-ROM  
drive in master mode.  
detected by the computer.  
1Insert the setup diskette in the diskette drive and change the directory to A:,  
compartment by pressing the Eject button.  
1Double-click on the My Computer icon on your desktop.  
2Double-click on the Control Panel folder.  
3Double-click on the System icon.  
DVD  
CD  
where A: is the diskette drive.  
After installing the DVD-ROM  
drive, the PC gets slower.  
DVD-ROM, DVD-VIDEO, DVD-R, DVD-RW, DVD-RAM, CD-DA(Audio),  
CD-ROM, CD-ROM XA, CD-Plus, CD-Extra, Photo-CD(Single,Multi-session),  
Video CD ready, Enhanced CD, CD-I/FMV, CD-R, CD-TEXT, CD-RW  
3Insert the disc (CD/DVD) with the label on the  
disc facing upwards and close the disc  
compartment by pressing the Eject button.  
To do so, type A: after the C:\ prompt and press [Enter].  
2Type CDSETUP and press [Enter].  
3Reboot the computer.  
Disc types supported  
Disc diameter  
Check the position of the jumper in the master/slave  
select terminal.  
DISC  
120mm or 80mm  
The DVD-ROM drive is not  
recognized by MS-DOS.  
Reinstall the device driver or update it with the latest  
version by downloading it from the Samsung Web site.  
The indicator light comes on.  
Sustained :  
4Click on the Device Manager tab.  
4 Play the disc (CD/DVD).  
Max. 21,600KB/sec (16X)  
/
Max. 7,200KB/sec (48X)  
5Expand the CD-ROM branch.  
Playing Audio CDs  
This case may occur when there is a Windows  
The DVD-ROM drive is not  
detected by Windows.  
Data transfer rate  
PIO Mode 4  
Multiword DMA mode 2 : 16.6MB/sec  
UDMA mode 2  
: 16.6MB/sec  
installation problem; reinstall Windows.  
The SAMSUNG DVD-ROM SD -  
device name is displayed.  
Run the CD player supplied with Windows or your sound card. You can listen to  
the CD by connecting headphones to the appropriate connector. If you have  
installed the appropriate player, such as Microsoft Windows Media Player, you can  
adjust the volume using the headphone volume control on the drive front panel.  
***  
:
33MB/sec  
100ms  
Manual Setup  
Check whether the audio cable is correctly connected  
to the sound output terminal on the DVD-ROM drive  
and the sound card CD-IN terminal.  
Check that the sound card is operational.  
Adjust the volume control.  
No sound is heard from an  
audio CD.  
The SAMSUNG device driver enables discs in the DVD-ROM drive to be read but  
not recorded in an MS-DOS environment; the driver is located in the D driver folder  
on the CD record utility disc.  
Access time(Random)  
Data buffer capacity  
Laser  
95ms  
512KB  
DRIVE  
1Make the C:\SAMSUNG directory.  
PERFORMANCE  
Playing Video CDs  
Set up and run the SOFT MPEG program.  
Semiconductor Laser  
Stepping motor  
Brushless motor  
2Copy the files from the diskette to the C:\SAMSUNG directory.  
Slide mechanism  
Spindle motor  
Install the latest version of the device driver.  
Check whether the CD is of good quality and clean it,  
if necessary.  
A CD is not read or is read  
too slowly.  
To do so, type COPY A: . C:\SAMSUNG after the C:\ prompt and press  
* *  
[Enter].  
Storing and Cleaning Your Discs  
Tray. DC motor(Soft Eject). Horizontal/Vertical  
10-15 / MODE1:10-12, MODE2:10-9  
Auto eject or Auto inject  
Loading mechanism  
DVD Region Protection Coding (RPC):  
The disc compartment will  
not open.  
Check that the power cable is correctly connected.  
ERROR RATE  
3Edit the CONFIG.SYS file.  
To ensure a long service life for your discs and drive, follow the precautions  
below when storing and cleaning your discs.  
Power off and disconnect the PC. Insert a pin or  
unfolded paper clip in the emergency hole and push  
firmly until the disc compartment opens.  
Eject button  
Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry.  
The RPC feature is supported on DVD players and is used with DVD-video  
discs (such as movies). Currently, the motion picture industry has divided the  
world into different regions or zones that correspond to the regional markets  
into which the motion picture industry releases movies. Simply put, RPC codes  
are placed on movies marketed throughout the world, based on the region of  
the world in which they are being sold. These RPC codes help control and pre-  
vent pirating of new movies into other motion picture regions prior to their true  
release dates within those markets.  
Indicator(LED)  
Headphone output  
BUSY  
LAST DRIVE = Z  
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  
FRONT PANEL  
REAR PANEL  
1Do not place a disc in direct sunlight.  
Stereo mini-jack(Ø3.6mm) 0.60V±20%(rms) 33  
Wheel knob  
Adjust the size of the replay screen.  
When the MPEG software plays a  
Video CD, the pictures are not  
regular and the running speed is  
too slow.  
Volume control  
Required power  
DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V  
2Store a disc vertically in a well-ventilated and  
After checking the display resolution, adjust it,  
if necessary.  
+5VDC : 2.0A, +12VDC : 1.0A  
ATAPI  
stable location.  
Interface connector  
Audio output  
Jumper block  
Operation  
4Edit the AUTOEXEC.BAT file.  
3Do not write or attach a label on a disc.  
Line out 0.7V ± 20%(rms) : 47KΩ  
Device configuration jumper  
Temperature : 5 ~ 45°C, Humidity : 10 ~ 80%  
Temperature : -25 ~ 60°C, Humidity : 10 ~ 90%  
148.2(W) x 42(H) x 184(D)mm (including Bezel)  
740g  
Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry.  
The computer may not recognize the disc if you start  
playback too quickly after inserting the disc.  
Open and close the disc compartment and try again.  
The Disc is not in message is  
displayed even though a disc  
has been inserted.  
4Do not drop a disc or place heavy objects on it.  
The SD-816 DVD-ROM drive supports RPC phase II. In the RPC-2 mode,  
the local code can be changed by users. RPC-2 is selected by default  
for the SD-816 DVD-ROM drive. You can change the region code up to  
five times via an MPEG application.  
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -  
C :\SAMSUNG\MSCDEX /D:SSCD000  
OPERATING  
ENVIRONMENT  
5Do not touch the surface of a disc; hold it by  
Clean the disc and try again.  
Storage  
the edges.  
Dimensions  
Net weight  
The interface mode of the sound card is AT-BUS.  
You must therefore connect the DVD-ROM drive to  
the IDE port on the PC mother board, rather than to  
the sound card, or install an IDE-compatible sound  
card.  
The DVD-ROM drive is not  
detected after it is connected  
to a sound card.  
GENERAL  
6To clean a disc, polish lightly from the inside  
Please contact your dealer or local SAMSUNG representative if you  
wish to change the local code more than five times.  
of the disc to the outside with a soft cotton cloth.  
5Reboot the computer.  
125,000 POH(Duty 20%)  
RELIABILITY  
MTBF  
7Do not leave the disc compartment open  
* In case of the PC without UDMA, it may have a different DVD data transmission rate.  
when you are not using it.  
6
7
5
8
9

U Line BI 95 User Manual
Talk electronic Thunder 22 User Manual
Sprint Nextel SPRINT PCS PM 225 User Manual
Sony MD Walkman MZ R500PC User Manual
Sony MD Walkman MZ R30 User Manual
Sony Cell Phone FS 1570 User Manual
Sony CDX 3160 User Manual
Sony CDX 656 User Manual
Samsung SGH A777MBAATT User Manual
Philips SPD5240 User Manual