SIIG 04 0589A User Manual

Dual 2.5" SATA MobileRack  
Quick Installation Guide  
Introducing the Dual 2.5" SATA  
The Dual 2.5" SATA MobileRack quickly converts two 2.5"  
SATA drives to removable & portable drives.  
KeyFeaturesandBenefits  
Tool-less/tray-less design for easy & fast HDD  
installation/swapping  
Easy to install in any standard 3.5 “ drive bay and  
compatible with all type of PC cases  
Made of high-quality aluminum for maximum  
durability & heat dissipation  
Supportsanycapacityof2.5"SerialATAHardDisk  
Drives  
Fully Serial ATA compatible - supports up to  
3GB/sec data transfer rates  
Serial Number Sticker  
For future product return or exchange, this serial number  
is required. Please keep it for your reference  
04-0589A  
1
SATA 7pin data  
SATA 15pin  
SATA 7pin data  
connector for HDD 1  
power connector  
connector for HDD 0  
Figure2:BackLayout  
Hardware Installation  
The Dual 2.5" SATA MobileRack fits into any available  
3.5" drive bay. General instructions for installing the  
mobile rack are provided below. Since the design of  
computer cases and motherboards vary, refer to your  
computer’s reference manual for further information, if  
needed.  
Static Electricity Discharge may permanently damage  
your system. Discharge any static electricity build up in  
your body by touching your computer’s case for a few  
seconds.  
1.  
2.  
4.  
Turn OFF the power to your computer and any  
other connected peripheral devices.  
Unplug the power cord from the back of the  
computer.  
Remove a front cover plate from the computer's  
3.5"drivebaybeforeinstallingyourDual2.5"SATA  
MobileRack.  
3
5.  
6.  
7.  
Slide the Dual 2.5" SATA MobileRack into the drive  
bay and secure it on each side using the mounting  
screws.  
Connect a power cable to the power connector that  
ismatchedwithyoursystem'spowersupplyoruse  
the supplied power adapter cable.  
ConnectoneendoftheSerialATAcabletothe Dual  
2.5" SATA MobileRack and the other end to the  
motherboard SATA port. Please repeat these steps  
if you are installing the second hard drive.  
8.  
Close your computer case.  
Installing the Hard Drive into the MobileRack  
1.  
Unlock upper and lower covers, then open the  
door (see Figure 3 on the next page).  
Note: Do not force the door to open while it is  
locked. Otherwise, you will damage the lock.  
2.  
3.  
Placeoneortwoharddrive(s)intheslot. Makesure  
the SATA connector is lined up with the connector  
inside the MobileRack.  
Carefully push the hard drive into the MobileRack  
sothatthedrive'sSATAconnectorisseatedsecurely,  
then close the door and lock it.  
Note: It must be in the lock position when in use.  
This prevents unexpected removal while working.  
4
Figure3: Openingcover  
To Verify Installation  
Since we didn’t load any additional driver under these  
Windows OSs, the only way to verify the Dual 2.5" SATA  
MobileRack works is actually connecting to a SATA  
controller.  
To Verify Hard Disk Drive Connectivity  
1.  
Check Device Manager to verify successfull  
installation.  
For Windows 2000/XP/Server 2003: Right click My  
Computer, then click Manage.  
For Windows Vista: Right click Computer, click  
Manage, then Continue.  
For Windows Server 2008: Right click Computer,  
click Manage, double click Diagnostics.  
ForWindows7: RightclickComputer,clickManage.  
Click Device Manager.  
2.  
3.  
DoubleclickDiskdrives,theserial/modelnumber  
of the hard drive should be displayed.  
5
Notes  
1.  
Do not open the door of the MobileRack while the  
hard drive is busy, this may cause damage to your  
hard drive.  
2.  
3.  
It must be in the lock position when in use. This  
prevents unexpected removal while working.  
Do not force the door to open while it is locked.  
Otherwise, you will damage the lock.  
6
Technical Support and Warranty  
QUESTIONS? SIIGsOnlineSupporthasanswers! Simplyvisitourwebsiteat  
www.siig.comandclick Support. Ouronlinesupportdatabaseisupdateddaily  
with new drivers and solutions. Answers to your questions could be just a few  
clicks away. You can also submit questions online and a technical support  
analysts will promptly respond.  
SIIGoffersa2-yearmanufacturerwarrantywiththisproduct. Pleaseseeourweb  
siteformorewarrantydetails. Ifyouencounteranyproblemswiththisproduct,  
pleasefollowtheproceduresbelow.  
Ifitiswithinthestore'sreturnpolicyperiod,pleasereturntheproducttothestore  
whereyoupurchasedfrom. Ifyourpurchasehaspassedthestore'sreturnpolicy  
period, pleasefollowthesestepstohavetheproductrepairedorreplaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit  
a
request to SIIG RMA. If the product is determined to be  
defective, an RMAnumber willbeissued.  
Step 2: After obtaining an RMA number, ship the product.  
Properlypacktheproductforshipping. Allaccessories thatcamewith  
theoriginalpackagemustbeincluded.  
ClearlywriteyourRMAnumberonthetopofthereturnedpackage. SIIG  
will refuse to accept any shipping package, and will not be responsible  
foraproductreturnedwithoutanRMAnumberpostedontheoutsideof  
theshippingcarton.  
You are responsible for the cost of shipping. Ship the product to the  
followingaddress:  
SIIG,Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA#:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
7
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturerofI/O  
connectivityproducts,includingPCI&ISAserialandparallelports,USB,Serial  
ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards,  
andotheraccessories. SIIGisthepremierone-stopsourceofupgrades.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendlyfeatures,  
and are backed by an extensive manufacturer warranty. High-quality control  
standards are evident by the overall ease of installation and compatibility of  
ourproducts, aswellasoneofthelowestdefectivereturnratesintheindustry.  
SIIG products can be found in computer retail stores, mail order catalogs,  
throughmajordistributors, systemintegrators, andVARsintheAmericasand  
theUK,andthroughe-commercesites.  
PRODUCT NAME  
Dual 2.5" SATA MobileRack  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Phone: 510-657-8688  
Dual2.5"SATAMobileRackisatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregistered  
trademarks of SIIG, Inc. Microsoft, Windows and Windows Vista are either registered  
trademarks or trademarks of Microsoft Corporation in the United States and/or other  
countries. Other names used in this publication are for identification only and may be  
trademarks of their respective companies.  
July, 2009  
Copyright © 2009 by SIIG, Inc. All rights reserved.  

XO Vision Xo Vision Shiner X140VIDB User Manual
Toastmaster MECF5 User Manual
Stanley Black & Decker CH2 User Manual
Sony USM4GJX User Manual
Sony SCD XB940 User Manual
Sony D E990 User Manual
Seagate SV35 SERIES ST31000525SV User Manual
Samsung SGH T729 SGH Blast Series User Manual
Samsung GH68 23213A User Manual
Nokia 700 User Manual