|
Nokia E61 User Guide
The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind, either express or implied, including,
but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or
contents of this document. Nokia reserves the right to revise this document or withdraw it at any time without prior notice
The availability of particular products may vary by region. Please check with the Nokia dealer nearest to you.
EXPORT CONTROLS
This device may contain commodities, technology, or software subject to export laws and regulations from the US and other countries. Diversion contrary
to law is prohibited.
Issue 5
.1
Contents
For your safety..............................................................7 Transfer content between devices.......................26
About your device....................................................................8 Transfer data with Bluetooth or infrared......................26
NETWORK SERVICES...................................................................8 Synchronize data with another device...........................27
Enhancements, batteries, and chargers............................8
Messages......................................................................28
Get started...................................................................10
Organize messages...............................................................28
Insert the SIM card and battery.........................................10 Search for messages.............................................................28
Insert and remove a memory card...................................11 Messaging settings................................................................28
Charge the battery.................................................................12 E-mail messages.....................................................................29
Switch on your device..........................................................12 Text messages........................................................................35
Enter first settings.................................................................13 Multimedia messages...........................................................37
Keys and parts.........................................................................13 Instant messaging.................................................................40
Keypad lock (keyguard).......................................................15 Special messages...................................................................43
Connectors...............................................................................16
Make calls.....................................................................44
Antennas...................................................................................16
Volume control.......................................................................17 Speed dial.................................................................................44
About the display...................................................................17 Answer a call...........................................................................45
Standby modes.......................................................................17 Divert calls................................................................................45
Display indicators..................................................................18 Call barring...............................................................................45
Memory.....................................................................................19 Video calls................................................................................46
Help and tutorial....................................................................21 Log..............................................................................................46
Nokia PC Suite.........................................................................21 Push to talk..............................................................................47
Nokia support and contact information.........................21 Net calls.....................................................................................50
Voice commands....................................................................52
Your device..................................................................23
Contacts........................................................................54
Menu..........................................................................................23
Scroll and make selections.................................................23 Manage contact groups.......................................................54
Write text.................................................................................24 Manage default information..............................................55
Change the writing language............................................24 Copy contacts between SIM and device
Common actions in several applications........................25 memory.....................................................................................55
Select ringing tones for contacts......................................55 File manager...........................................................................75
Business cards.........................................................................55 Documents...............................................................................75
Sheet..........................................................................................77
Calendar........................................................................57
Presentation............................................................................78
Create calendar entries........................................................57 Screen export..........................................................................80
To-do..........................................................................................57 Print............................................................................................81
Calendar views........................................................................58
Organiser......................................................................82
Notes..........................................................................................82
Calculator..................................................................................82
Converter..................................................................................82
Voice mailbox..........................................................................83
Add a received calendar entry to your calendar..........58
Clock...............................................................................59
Connectivity.................................................................60
Internet access points..........................................................60
Wireless LAN............................................................................62
Data and software management..........................84
Cable connection....................................................................62 Application manager............................................................84
Bluetooth..................................................................................63 Remote configuration network service..........................84
Infrared.....................................................................................66 Data synchronization............................................................84
Data connections...................................................................67
Connection manager............................................................68 Tools...............................................................................86
Modem......................................................................................69 Nokia Catalogs........................................................................86
Mobile VPN ..............................................................................70 Sett. wiz....................................................................................86
Email data roaming...............................................................70 Voice aid...................................................................................86
Web................................................................................71 Media applications....................................................88
Access points...........................................................................71 Gallery........................................................................................88
Browse the Web.....................................................................71 RealPlayer ................................................................................89
Bookmarks...............................................................................72 Music player.............................................................................90
Download items.....................................................................72 Recorder....................................................................................92
End a connection....................................................................72 Flash player..............................................................................92
News feeds and blogs..........................................................73
Web settings...........................................................................73 Personalization...........................................................93
Services.....................................................................................74 Profiles......................................................................................93
Themes......................................................................................94
Office applications.....................................................75
Call settings..............................................................................96
Connection settings..............................................................97
Date and time settings......................................................101
Security settings..................................................................101
Enhancement settings.......................................................101
Security.......................................................................103
Device security ....................................................................103
Certificate manager............................................................105
VPN...........................................................................................105
Security settings for wireless LAN access
points......................................................................................105
Shortcuts....................................................................106
Battery information................................................108
1500 mAh Li-Ion battery (BP-5L) information...........108
Nokia battery authentication guidelines....................108
Care and maintenance...........................................111
Additional safety information.............................112
Operating environment.....................................................112
Medical devices....................................................................112
Vehicles...................................................................................113
Potentially explosive environments..............................113
Emergency calls....................................................................113
CERTIFICATION INFORMATION (SAR)................................114
Index............................................................................116
For your safety
Read these simple guidelines. Not following them may
be dangerous or illegal. Read the complete user guide
for further information.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the device
where blasting is in progress.
SWITCH ON SAFELY
USE SENSIBLY
Do not switch the device on when wireless
phone useis prohibitedorwhenitmaycause
interference or danger.
Use only in the normal position as explained
in the product documentation. Do not touch
the antennas unnecessarily.
ROAD SAFETY COMES FIRST
QUALIFIED SERVICE
Obey all local laws. Always keep your hands
free to operate the vehicle while driving.
Your first consideration while driving should
be road safety.
Only qualified personnel may install or repair
this product.
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and
batteries. Do not connect incompatible
products.
INTERFERENCE
All wireless devices may be susceptible to
interference, which could affect
performance.
WATER-RESISTANCE
Your device is not water-resistant. Keep it
SWITCH OFF IN HOSPITALS
dry.
Follow any restrictions. Switch the device off
BACK-UP COPIES
near medical equipment.
Remember to make back-up copies or keep
a written record of all important
information.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can
cause interference in aircraft.
CONNECTING TO OTHER DEVICES
SWITCH OFF WHEN REFUELLING
When connecting to any other device, read
its user guide fordetailedsafetyinstructions.
Do not connect incompatible products.
Do not use the device at a refueling point. Do
not use near fuel or chemicals.
7
EMERGENCY CALLS
and explain what charges will apply. Some networks
may have limitations that affect how you can use
network services. For instance, some networks may not
support all language-dependent characters and
services.
Ensure the phone function of the device is
switched on and in service. Press the end key
as many times as needed to clear the display
and return to the standby mode. Enter the
emergency number, then press the call key.
Give your location. Do not end the call until
given permission to do so.
Your service provider may have requested that certain
features be disabled or not activated in your device. If
so, they will not appear on your device menu. Your
device may also have been specially configured. This
configuration may include changes in menu names,
menu order and icons. Contact your service provider for
more information.
About your device
The wireless device described in this guide is approved
for use on the GSM 850/900/1800/1900, UMTS 2100
networks. Contact your service provider for more
information about networks.
This device supports WAP 2.0 protocols (HTTP and SSL)
that run on TCP/IP protocols. Some features of this
device, such as multimedia messaging, browsing, e-
mail, and content downloading using the browser,
require network support for these technologies.
When using the features in this device, obey all laws,
and respect privacy and legitimate rights of others.
Warning: Touseany featuresinthis device, other
than the alarm clock, the device must be switched on.
Do not switch the device on when wireless device use
may cause interference or danger.
Enhancements, batteries,
and chargers
Check the model number of any charger before use with
this device. This device is intended for use when
supplied with power from the AC-4, AC-3 and DC-4
chargers and from ACP-8, ACP-9, ACP-12, LCH-8, LCH-9,
LCH-12 and AC-1 when used with the CA-44 adapter.
NETWORK SERVICES
To use the phone you must have service from a wireless
service provider. Many of the features in this device
depend on features in the wireless network to function.
These network services may not be available on all
networks or you may have to make specific
Warning: Use only batteries, chargers, and
enhancements approved by Nokia for use with this
particular model. The use of any other types may
invalidate any approval or warranty, and may be
dangerous.
arrangements with your service provider before you
can utilize network services. Your service provider may
need to give you additional instructions for their use
8
For availability of approved enhancements, please
check with your dealer. When youdisconnect the power
cord of any enhancement, grasp and pull the plug, not
the cord.
Your device and its enhancements may contain small
parts. Keep them out of reach of small children.
9
Get started
Note: Your service provider may have requested
that certain features be disabled or not activated in
your device. If so, they do not appear on your device
menu. Your device may also have been specially
configured for your network provider. This
configuration may include changes in menu names,
menu order and icons. Contact your service provider for
more information.
Model number: Nokia E61-1
Hereinafter referred to as Nokia E61.
2. If the battery is installed, lift the battery from the
battery compartment in the direction of the arrow
to remove it .
Insert the SIM card and
battery
Keep all SIM cards out of the reach of small children.
For availability and information on using SIM card
services, contact your SIM card vendor. This may be the
service provider, network operator, or other vendor.
1. Always switch the device off, and disconnect the
charger before removing the battery.
With the back of the device facing you, press and
hold the cover release button (1), and slide the back
cover in the direction of the arrow (2).
10
3. Ensure that the beveled corner of the SIM card is
pointing towards the bottom of the device and that
the contact area on the card is facing the device,
then insert the SIM card (1) into the SIM card slot (2).
5. Insert the locking catches of the back cover into the
corresponding slots (1), and slide the cover in the
direction of the arrow (2).
Instead of a SIM card, you may also have a USIM card,
which is an enhanced version of the SIM card and is
supported by UMTS (network service) mobile phones.
Contact your service provider for more information.
4. To insert the battery, align the contacts of the
battery with the corresponding connectors on the
battery compartment, insert in the direction of the
arrow, and gently click the battery into place.
Insert and remove a
memory card
If you have a memory card, follow the instructions to
insert and remove it.
See "Memory," p. 19.
1. Remove the battery cover.
2. Insert the memory card (1) fully into the memory
card slot (2) to lock in place. Ensure that the contact
area is facing down.
11
charger to the adapter, and the adapter to the
bottom of the device.
3. Connect the power cord to the battery charger
adapter. The battery indicator bar starts scrolling on
the display. If the battery is completely discharged,
it may take a few minutes before the charging
indicator is shown. The device can be used while
charging.
4. When the battery is fully charged, the bar stops
scrolling. Disconnect the charger from the device,
then from the outlet.
When the battery charge level is too low for operation,
the device switches itself off.
3. Replace the battery cover.
4. To remove the memory card, remove the battery
cover and push the memory card into the device to
activate the release mechanism. Then, gently pull
the card out of your device.
Switch on your device
1. To switch the device on, press the power key.
Important: Do not remove the memory card
in the middle of an operation when the card is being
accessed. Removing the card in the middle of an
operation may damage the memory card as well as
the device, and data stored on the card may be
corrupted.
2. If the device asks for a PIN code (or UPIN code, if you
have a USIM card), lock code or security code, enter
the code, and select OK.
3. To switch the device off, press the power key.
Charge the battery
Tip: When you switch the device on, it may
recognize the SIM card provider and configure
the correct text message, multimediamessage,
and GPRS settings automatically. If not, contact
1. Connect the charger to a wall outlet.
2. Connect the charger to the bottom of the device. If
you have a battery charger adapter, connect the
12
your service provider for the correct settings,
or use the Sett. wizard application.
The device can be used without the network dependant
phone functions when a SIM card is not inserted or
when the Offline profile is selected.
Keys and parts
Enter first settings
When you power on the device for the first time, or
when you switch on the device after the battery has
been removed for a longer period, your device asks for
a city, time, and date. You can change these settings
later in Clock.
1. Select the city in which you are located from the list
and OK. To browse for a city, start to type the name
of the city, or scroll to a city. It is important to select
the correct city, because scheduled calendar entries
that you create can change if the new city is located
on a different time zone.
2. Set the time, and select OK.
3. Set the date, and select OK.
1 — Power key
2 — Left selection key, joystick, and right selection key
3 — End key
4 — E-mail key
5 — Backspace key
6 — Enter key
7 — Chr key
8 — Shift key
9 — Ctrl key
10 — Spacebar
13
11 — Blue function key
12 — Phone keypad
13 — Menu key
Phone > Standby mode, and the applications in Left
selection key and Right selection key.
Joystick
Press the joystick to edit or make a selection, or to
access commonly used functions in the different
applications. Use the joystick to scroll left, right, up,
down, or to move around on the display (for example,
when browsing). In the standby mode, scroll with or
press the joystick for different shortcuts. To change the
shortcuts, select Menu > Tools > Settings > Phone >
Standby mode > Active standby > Off, and the shortcuts
in Navigationkeyright, Navigation key left, Navigat. key
down, Navigation key up, and Selection key.
14 — Call key
15 — Voice key
16 — Volume keys
17 — Loudspeaker
18 — E-mail indicator light
Call and end keys
To answer a call, press the call key. In the standby mode,
press the call key to access the Log.
To reject a call, end active calls and held calls, and close
applications, press the end key. Press and hold the end
key to end data connections (GPRS, data call).
E-mail key
1 — Loudspeaker
2 — Volume keys
3 — Voice key
To access your default e-mail inbox, press the e-mail
key. If you have not set up an e-mail account, the
mailbox guide opens to help you. If you press and hold
the e-mail key, your default e-mail editor opens. The
functionality depends also on your mailbox service
provider. You can configure the e-mail key yourself. See
"Configure the e-mail key," p. 30.
Key functions
Selection keys
Press either selection key to use the command that is
shown on the display above the selection keys. See
"Standby modes," p. 17. To change the shortcuts in
the standby mode, select Menu > Tools > Settings >
Chr key
To insert characters that you cannot insert with the
keypad, press the Chr key when you are writing.
14
To scroll through a list of accented characters, press and device, press the menu key in the standby modes. To
hold the Chr key, then press the other key as many times return to Menu from an application, leaving the
as you need to get the accented character you want.
Shift keys
application open in the background, press the menu
key. Press and hold the menu key to see a list of the
active applications and switch between them. In this
user guide, "select Menu" refers to pressing this key.
To enter an uppercase letter in the middle of lowercase
letters or a lowercase letter in the middle of uppercase
Voice key
letters, press the shift key so that
display, then the key you want.
is shown on the
Press the voicekey toopen Recorder and startrecording
a memo. Press and hold the voice key to use voice
commands. See "Voice commands," p. 52.
To enter only uppercase letters, press the shift key
twice, so that is shown on the display. To enter
only lowercase letters again, press the shift key twice,
so that is shown on the display.
Keypad lock (keyguard)
To select text, press the shift key, and scroll left or right.
When the keypad lock is on, calls may be possible to the
official emergency number programmed into your
device.
Blue function key
To enter a character marked in blue, press the blue
Use the keypad lock to prevent the keys on the device
function key, so that
the key you want.
is shown on the display, then
from being accidentally pressed.
To lock the keypad in the
standby mode, press the
left selection key (1) and
the blue function key (2).
To unlock, press the left
selection key and the blue
function key again.
To enter only characters marked in blue, press the blue
function key twice so that
is shown on the display,
then the characters you want.
To activate Bluetooth, press the blue function key and
Ctrl key simultaneously. To deactivate Bluetooth, press
the blue function key and Ctrl key again.
Tip: To lock the
To activate infrared, press the blue function key and Chr
keypad in the
key simultaneously.
Menu or in an open application, press the
power key briefly, and select Lock keypad. To
unlock, press the left selection key and the blue
function key.
Menu key
Leaving applications running in the background
increases the demand on battery power and reduces
the battery life. To access the applications in your
15
You can also lock the device in the standby mode using
your lock code. Press the power key, select Lock
phone, and enter your lock code. The default lock code
is 12345. To unlock, press the left selection key, enter
your lock code, and press the joystick.
Infrared port
Connectors
Warning: When you use the headset, your ability
to hear outside sounds may be affected. Do not use the
headset where it can endanger your safety.
Pop-Port™
connector for
headset and
other
Antennas
Your device has two internal antennas.
Note: As with any other radio transmitting
device, do not touch either of the antennas
enhancements
unnecessarily when the device is switched on. Contact
with the antenna affects call quality and may cause the
device to operate at a higher power level than
otherwise needed. Not touching the antenna area
during a phone call optimises the antenna performance
and the talktime of your device.
Battery
charger
connector
16
The picture shows the normal use of
the device at the ear for voice calls.
Standby modes
Your device has two different standby modes: active
standby mode and standby mode.
Active standby mode
After you have switched on your device and it is ready
for use, but you have not entered any characters or
made other selections, the device is in the active
standby mode. In the active standby mode, you can
view your service provider and network, different
indicators such as indicators for alarms, and
applications you want to access fast. You can, for
example, view calendar information such as the day's
meetings in the active standby mode. Scroll to the
information, and press the joystick to open calendar for
details.
Volume control
Warning: Do not hold the device near your ear
when the loudspeaker is in use, because the volume
may be extremely loud.
To adjust the volume during a call, press the volume
To select the applications that you want to access from
keys.
active standby, select Menu > Tools > Settings >
To adjust the volume when using the loudspeaker,
press the volume keys.
Phone > Standby mode > Active standby apps.. Scroll to
the different shortcut settings, and press the joystick.
Scroll to the desired application, and press the joystick.
You can see the messages in a messaging folder such
as inbox or mailbox in the active standby mode. Select
Menu > Tools > Settings > Phone > Standby mode and
the folders in Active standby mailbox.
About the display
A small number of missing, discolored, or bright dots
may appear on the screen. This is a characteristic of this
type of display. Some displays may contain pixels or
dots that remain on or off. This is normal, not a fault.
To use the basic standby mode, select Menu > Tools >
Settings > Phone > Standby mode > Active standby >
Off.
To call your voice mailbox (network service), press and
hold 1.
17
To open Services and connect to the Web, press 0.
Display indicators
The device is being used in a GSM network. The bar
Standby mode
next to the icon indicates the signal strength of the
network at your current location. The higher the bar,
the stronger the signal.
In the standby mode, you can see different information,
such as your service provider, time, and different
indicators, such as indicators for alarms.
The device is being used in a UMTS network
(network service). The bar next to the icon indicates the
signal strength of the network at your current location.
The higher the bar, the stronger the signal.
In the standby mode, you can use the following
shortcuts. These shortcuts are usually not available in
the active standby mode, where the joystick is used for
normal scrolling.
The battery charge level. The higher the bar, the
stronger the charge in the battery.
To view the most recently dialed numbers, press the call
key. Scroll to a number or name, and press the call key
again to call the number.
You have one or more unread messages in the
To call your voice mailbox (network service), press and Inbox folder in Messag..
hold 1.
You have received new e-mail in the remote
To view calendar information, scroll right.
To write and send text messages, scroll left.
To open the contacts list, press the joystick.
mailbox.
The device keypad is locked.
The device is locked.
To change the profile, press the power key briefly, scroll
to the profile you want, and press the joystick to
activate the profile.
You have one or more missed phone calls.
An alarm is active.
You have selected the silent profile, and the device
To open Services and connect to the Web, press 0.
does not ring for an incoming call or message.
To change these shortcuts, select Menu > Tools >
Settings > Phone > Standby mode.
Bluetooth is activated.
An infrared connection is active. If the indicator
blinks, your device is trying to connect to the other
device, or the connection has been lost.
18
A hands-free car kit is connected to the device.
A loopset is connected to the device.
Text phone is connected to the device.
Your device is synchronizing.
A GPRS or EGPRS packet data connection is available.
A GPRS or EGPRS packet data connection is active.
A GPRS or EGPRS packet data connection is on hold.
A UMTS packet data connection is available.
A UMTS packet data connection is active.
You have an ongoing push to talk connection.
,
,
Indicators for the selected character
A UMTS packet data connection is on hold.
mode.
You have set the device to scan for wireless LANs,
and a wireless LAN is available.
You have pressed the blue function key once to
insert a number or a character marked with blue color
on the keypad.
A wireless LAN connection is active in a network
You have pressed the blue function key twice to
that does not have encryption.
insert only numbers or characters marked with blue
A wireless LAN connection is active in a network
that has encryption.
color on the keypad.
You have pressed the shift key once to insert an
Your device is connected to a PC with a USB data
uppercase letter in the middle of lowercase letters, or
a lowercase letter in the middle of uppercase letters.
cable.
A data call is active.
IP passthrough is active.
Memory
and Indicate the phone line that you have selected,
There are two types of memory into which you can save
data or install applications: device memory and
removable memory.
if you have subscribed to two phone lines (network
service).
All calls are forwarded to another number.
A headset is connected to the device.
Memory details
The connection to a headset with Bluetooth
connectivity has been lost.
Select Menu, and Options > Memory details and Phone
19
mem. or Memory card.
You can see how much memory is currently in use, how it. To format a memory card, select Options > Format
much free memory remains, and how much memory is mem. card. When formatting is complete, enter a name
consumed by each data type. For example, you can see for the memory card.
how much memory your e-mail messages, text
documents, or calendar appointments consume.
Back up and restore to the memory card
It is recommended to back up device memory regularly
to the memory card. The information can be restored
to your device later. Do not remove the memory card in
the middle of an operation when the card is being
accessed. Removing the card in the middle of an
operation may damage the memory card as well as the
device, and data stored on the card may be corrupted.
To back up information from device memory to a
memory card, select Menu > Tools > Memory card >
Options > Backup phone mem.. To restore information
from the memory card to the device memory, select
Menu > Tools > Memory card > Options > Restore from
card.
Tip: To ensure that you have adequate
memory, you should regularly delete or
transfer data to a memory card or PC.
Memory card
This device uses a mini Secure Digital (SD)
card.
Use only compatible miniSD cards with this
device. Other memory cards, such as MultiMediaCards,
reduced-size MultiMediaCards or full-size SD cards, do
not fit in the memory card slot and are not compatible
with this device. Using an incompatible memory card
may damage the memory card as well as the device,
and data stored on the incompatible card may be
corrupted.
If you cannot use a memory card in your device, you
may have the wrong type of memory card, the card may
not be formatted for your device, or the card has a
corrupted file system.
Tip: You can insert and remove a memory card
without removing the battery or switching off
the device.
Your Nokia device supports the FAT16 and FAT32 file
systems for memory cards. If you use a memory card
from another device or if you want to ensure
compatibility of the memory card with your Nokia
device, you may need to format the memory card with
yourNokiadevice. However, alldata in the memorycard
is permanently deleted if you format the memory card.
Memory card security
You can protect a memory card with a password to
prevent unauthorized access. To set a password, select
Options > Set password. The password can be up to 8
characters long and is case-sensitive. The password is
stored in your device and you do not need to enter it
again while you use the memory card on the same
Format a memory card
When a memory card is formatted, all data on the card
is lost permanently. Consult your retailer to find out if
you must format the memory card before you can use
20
device. If you use the memory card on another device,
you are asked for the password. Not all memory cards
support password protection.
To remove the memory card password, select Options >
Remove password. When you remove the password,
the data on the memory card is not protected against
unauthorized use.
Tutorial
The tutorial provides you information about your
device and shows you how to use it. Some tutorial
content may be located on a memory card. You must
insert the memory card in the device before you can
access it.
To access the tutorial in the Menu, select Menu > Help,
open Tutorial and the section you want to view.
Help and tutorial
You can find answers to your questions while using the
device even with no user guide present, because your
device includes both a help and a tutorial.
Nokia PC Suite
You can install Nokia PC Suite from the CD-ROM or from
the Web. Nokia PC Suite can be used only with Windows
2000 and Windows XP. With Nokia PC Suite, you can
make backups, synchronize your device with a
compatible computer, move files between your device
and a compatible computer, or use your device as a
modem.
Device help
You can access the device help from an open application
or from the Menu. When you have an application open,
selectOptions > Help to read instructions for the current
view.
Nokia support and contact
information
To open help from Menu, select Menu > Help > Help. In
Help, you can select categories for which you want to
see instructions. Scroll to a category, such as Messaging,
and press the joystick to see what instructions (help
topics) are available. While you are reading the topic,
scroll left or right to see the other topics in that
category.
When you are reading the instructions, press and hold
the menu key to switch between help and the
application that is open in the background.
Check www.nokia.com/support or yourlocalNokia Web
site for the latest version of this guide, additional
information, downloads, and services related to your
Nokia product.
On the Web site, you can get information on the use of
Nokia products and services. If you need to contact
customer service, check the list of local Nokia contact
centers at www.nokia.com/customerservice.
21
For maintenance services, check your nearest Nokia
service center at www.nokia.com/repair.
22
Your device
When you switch the device on, it may recognize the
SIM card provider and configure the correct text
message, multimedia message, and GPRS settings
automatically. You may also receive the settings as a
special text message from your service provider.
To move an application to a different folder, scroll to
the application you want to move toanother folder, and
select Options > Move to folder, the new folder, and
OK.
To download applications from the Web, select
Options > App. downloads.
To create a new folder, select Options > New folder. You
Menu
cannot create folders inside folders.
The Menu is a starting point from which you can open
all applications in the device or on a memory card. The
Menu contains applications and folders, which are
groups of similar applications. Use the joystick to scroll
up and down on the screen.
To rename a new folder, select Options > Rename.
Tip: To switch between several open
applications, press and hold the menu key. The
application-switching window opens and
displays the open applications. Scroll to an
application, and press the joystick to switch to
it.
Applications that you install are saved in the Installat.
folder by default.
To open an application, scroll to it, and press the
joystick.
To view the applications in a list, select Options >
Change view > List. To return back to the grid view,
select Options > Change view > Grid.
To view the memory consumption of different
applications and data stored on the device or memory
card and to check the amount of free memory, select
Options > Memory details and the memory.
To rearrange the folder, scroll to the application you
want to move, and select Options > Move. A check mark
is placed beside the application. Scrolltoa new location,
and select OK.
Scroll and make selections
Use the joystick to move and make selections. With the
joystick, you can move up, down, left and right in the
Menu or in different applications or lists. You can also
press the joystick to open applications, files, or edit
settings.
To select text, press and hold the shift key, and scroll
left or right until you have selected the text.
To select different items, such as messages, files, or
contacts, scroll up, down, left or right to highlight the
23
item you want to select. Select Options > Mark/
Unmark > Mark to select one item or Options > Mark/
Unmark > Mark all to select all items.
To select an object (for example, an attachment in a
document) scroll to the object so that square markers
appear on each side of the object.
other key as many times as is needed before the
character you want is shown.
To switch between the different character cases, press
the shift key, so that
is shown on the display.
Copy and paste text
1. To select letters and words, press and hold the shift
key. At the same time, scroll in the direction
necessary to highlight the word, phrase, or line of
text you want to copy. As the selection moves, the
text is highlighted.
Write text
Your device has a full keyboard. Most common
punctuation marks either have a key of their own or
they can be entered by pressing a combination of keys.
,
and
indicate the selected case.
2. To copy the text to the clipboard, press Ctrl+C. To
insert the text into a document, press Ctrl+V.
Some characters (for example, punctuation marks and
symbols) are marked in blue color on the keys. To insert
a character marked in blue, press the blue function key,
and the key that has the blue character you want.
Change the writing
language
To insert a number, press the blue function key so that
is shown on the display, and a key with a number
When you write text, you can change the writing
language. When you are writing and press Chr+a key
several times to use a specific character, changing the
writing language gives you access to different
characters.
on the blue background. To lock the blue function key
and insert only numbers, press the blue function key
twice so that
is shown on the display.
To erase a character, press the backspace key. Press and
hold the backspace key to clear more than one
character.
For example, if you are writing a message using a non-
Latin alphabet and want to add a person's name using
Latin alphabets, select Options > Writing language and
a writing language that uses Latin characters.
To open a list of special characters, press the Chr key.
Use the joystick to scroll through the list and select a
character.
To add characters by using other keys such as "A" or "O",
24
press and hold the Chr key and simultaneously press the
Common actions in several
applications
You can find the following actions in several
applications:
To switch between open applications, press and hold
the menu key to see a list of open applications. Select
an application.
To change the profile or switch off or lock the device,
press the power key briefly.
To save a file, select Options > Save. There are different
save options depending on the application you use.
To send a file, select Options > Send. There are different
send options depending on the application you use, for
example e-mail or multimedia messages, infrared or
Bluetooth.
To print to a compatible printer, select Options > Print.
You can preview items that you want to print, or edit
the way printed pages look. Before you can print, you
must define a compatible printer to your device. See
"Print," p. 81.
To delete a file, press the backspace key, or select
Options > Delete.
25
Transfer content between devices
You can transfer content, such as contacts, from a
compatible Nokia device to your Nokia E61 using
Bluetooth connectivity or infrared. The type of content
that can be transferred depends on the phone model.
If the other device supports synchronization, you can
also synchronize data between the other device and
your Nokia E61.
5. Select your other device from the list. You are asked
to enter a passcode (1 to 16 digits) on your Nokia
E61. The passcode is used only once to confirm this
connection.
6. Enter the code on your Nokia E61, and select OK.
Enter the passcode on your other device, and select
OK. The devices are now paired. See "Pair
devices," p. 64.
For some phone models, the Transfer data
application is sent to your other device as a
message. To install Transfer data on your other
device, open the message, and follow the
instructions on the display.
Transfer data with
Bluetooth or infrared
Tip: If you transfer data from your previous
device, the device may require you to insert the
SIM card. Your Nokia E61 does not need a SIM
card when transferring data.
7. From your Nokia E61, select the content you want
to transfer from your other device, and OK.
Infrared connectivity
To start transferring data from a compatible device,
1. In the information view, select Continue.
select Menu > Tools > Transfer.
2. Select Via infrared. Both devices must support the
Bluetooth connectivity
selected connection type.
1. In the information view, select Continue.
3. Connect the two devices. See "Infrared," p. 66.
2. Select Via Bluetooth. Both devices must support the
4. From your Nokia E61, select the content you want
selected connection type.
to transfer from your other device, and OK.
3. Activate Bluetooth in your other device, and select
Continue in your Nokia E61 to start searching for
devices with active Bluetooth connectivity.
Content is copied from the memory of the other device
to the corresponding location in your device. Copying
time depends on the amount of data to be transferred.
You can also cancel and continue later.
4. Select Stop in your Nokia E61 after it has found your
other device.
26
The necessary steps for data transfer may vary
depending on your device, and whether you have
interrupted data transfer earlier. The items that you can
transfer vary depending on the other device.
Synchronize data with
another device
If you have previously transferred data to your Nokia
E61, and your other device supports synchronization,
you can use Transfer to keep the data of the two devices
up to date.
1. Select Phones, and press the joystick.
2. Scroll to the device from which you transferred data,
and press the joystick.
3. Select Synchronise, and press the joystick. The
devices start synchronizing using the same
connection type that you selected when you
originally transferred data. Only the data that you
originally selected for data transfer is synchronized.
To modify the data transfer and synchronization
settings, select Synchronise, scroll to a device, press the
joystick, and select Edit.
27
Messages
OK. You can only rename folders that you have created.
message, and select Options > Move to folder, the
folder, and OK.
To sort messages in a specific order, select Options >
Sort by. You can sort the messages by Date, Sender,
Subject, or Message type.
Select Menu > Messag..
Before sending or receiving messages, you may need to
do the following:
•
•
Insert a valid SIM card in the device and be located
in a service area of the cellular network.
Verify that the network supports the messaging
features you want to use and that they are activated
on your SIM card.
•
•
•
•
Define Internet access point (IAP) settings on the
device. See "Access points," p. 97.
Search for messages
Define e-mail account settings on the device. See "E-
mail account settings," p. 33.
To search for a message, open the folder in which you
want to search, select Options > Find. Enter the search
term, and select OK.
Define SMS settings on the device. See "Text message
settings," p. 36.
Define MMS settings on the device. See "Multimedia
message settings," p. 39.
Messaging settings
The device may recognize the SIM card provider and
automatically configure some of the message settings.
If not, you may need to define the settings manually, or
contact your service provider, network operator, or
Internet service provider to configure the settings.
Select Options > Settings.
To define or edit settings for different message types,
select Text message, Multimedia message, E-mail,
Service message, Cell broadcast, or Other.
See "Text message settings," p. 36.
See "Multimedia message settings," p. 39.
See "E-mail account settings," p. 33.
Organize messages
To create a new folder to organize your messages,
select My folders > Options > New folder. Enter the
folder name, and select OK.
28
•
Set up an e-mail account, and define the e-mail
settings correctly. See "E-mail account
settings," p. 33.
Other settings
Select Menu > Messag. > Options > Settings > Other.
Select from the following:
Follow the instructions from your remote mailbox and
Internet service providers. Contact your network and
Internet service providers or operator for the correct
settings.
•
Save sent messages — Select whether to store sent
messages in the Sent folder.
•
No. of saved msgs. — Enter the number of sent
messages that you want to save. When the limit is
reached, the oldest message is deleted.
Folder view — Define whether you want the list of
messages in the folders to be shown on one row or
two rows.
Set up your e-mail
•
•
If you select Mailbox and have not set up your e-mail
account, you are prompted to do so. To start setting up
the e-mail account with the mailbox guide, select Yes.
Memory in use — Select where to save your received
messages. You can save messages to memory card
only if a memory card is inserted.
1. To start entering the e-mail settings, select Start.
2. In Mailbox type, select IMAP4 or POP3, and select
The settings available for editing may vary.
Next.
Tip: POP3 is a version of the post office
protocol that is used to store and retrieve
e-mail or Internet mail messages. IMAP4 is
a version of the Internet message access
protocol that lets you access and manage
e-mail messages while the messages are
still on the e-mail server. You can then
choose which messages to download to
your device.
E-mail messages
To receive and send mail, you must have a remote
mailbox service. This service may be offered by an
Internet service provider, a network service provider, or
your company. Your device is compliant with Internet
standards IMAP4 (revision 1) and POP3, and with
different push e-mail solutions. Other e-mail providers
may offer services with different settings or features
than those described in this user guide.
3. In My e-mail address, enter your e-mail address.
Select Next.
Before you can send, receive, retrieve, reply to, and
forward mail on your device, you must also do the
following:
4. In Incoming mail serv., enter the name of the
remote server that receives your e-mail, and select
Next.
•
Configure an Internet access point (IAP). See "Access
5. In Outgoing mailserv., enterthename ofthe remote
points," p. 97.
29
server that sends your e-mail, and select Next.
Depending on your mobile operator, you might
have to use your mobile operator's outgoing mail
server instead of your e-mail provider's.
Configure the e-mail key
Your device has an e-mail key. With the e-mail key, you
can access your default e-mail inbox or open your
default e-mail editor from the active standby. The
functionality depends also on your mailbox service
provider.
6. In Access point, select the Internet access point your
device should use when it retrieves the e-mails. If
you select Always ask, each time the device starts to
retrieve e-mail, it asks which Internet access point
it should use, but if you select an access point, the
device makes the connection automatically. Select
Next.
To configure the e-mail key, select Menu > Tools > E-
mail key. Select the e-mail account that you want to use
with the e-mail key.
Tip: If you select Select group, the device
makes the connection automatically using
the best available Internet access point
from the access point group. Select the
access point group and Back to save the
selection.
Connect to mailbox
E-mail addressed to you is not automatically received
by your device, but by your remote mailbox. To read
your e-mail, you must first connect to the remote
mailbox; then select the e-mails you wish to retrieve
into your device. To receive and send e-mail, you need
to register for an e-mail service. To set up a mailbox in
your device, select Messag. > Options > Settings > E-
mail > Options > New mailbox. Contact your service
provider for the correct settings.
7. Enter a name for your new mailbox, and select
Finish.
When you create a new mailbox, the name you give to
the mailbox replaces Mailbox in the Messag. main view.
Select your default mailbox
To retrieve received e-mail messages to your device and
view them offline, select your mailbox in the Messag.
main view. When the device asks Connect to mailbox?,
select Yes.
To view e-mail messages in a folder, scroll to the folder,
and press the joystick. Scroll to a message, and press
the joystick.
To retrieve e-mail messages to your device, select
Options > Retrieve e-mail > New to retrieve new
messages that you have neither read nor retrieved,
Selected to retrieve only messages you select from the
If you have defined several mailboxes, you can select
one of them as your default mailbox. To define the
default mailbox, select Options > Settings > E-mail >
Mailbox in use and the mailbox.
If you have defined several mailboxes, you must select
the mailbox that you want to use every time you start
composing a new e-mail message.
30
remote mailbox, or All to retrieve all messages not
previously retrieved.
Some options require you to connect to your remote
mailbox.
Tip: To subscribe to other folders in your
remote mailbox, select E-mail settings >
Retrievalsettings > Foldersubscriptions. E-mail
in all subscribed folders is updated when you
retrieve e-mail from your remote mailbox.
To disconnect from a remote mailbox, select Options >
Disconnect.
View e-mail offline
Working offline means that your device is not
connected to a remote mailbox. Managing your e-mail
offlineenables youtosaveinconnectioncostsandwork
in conditions that do not allow a data connection. Any
changes you make in the remote mailbox folders while
offline take effect in your remote mailbox the next time
you go online and synchronize. For example, if you
delete an e-mail from your device when offline, the e-
mail is deleted from the remote mailbox the next time
you connect to the mailbox.
E-mail indicator light
You can set the indicator light on the cover of your
device to blink when a new e-mail arrives to your
device.
Select Menu > Messag. > Options > Settings > E-mail.
Define in Indicator light settings how long you want the
indicator light to blink, or whether you want it to blink
at all.
1. Select Messag. > Options > Settings > E-mail. Select
the e-mail account, and press the joystick. Select
Retrieval settings > E-mail to retrieve > Msgs. &
attachs. to retrieve entire messages with their
attachments to your device.
Read and reply to e-mail
Important: E-mail messages may contain viruses
or otherwise be harmful to your device or PC. Do not
open any attachment if you are not sure of the
trustworthiness of the sender.
2. Open your mailbox, and select Options > Retrieve e-
mail. Select New to retrieve new messages that you
have neither read nor retrieved, Selected to retrieve
only messages you select from the remote mailbox,
or All to retrieve all messages not previously
retrieved. The device goes online and connects to
the mailbox to retrieve the mails.
To read a received e-mail, scroll to the e-mail, and press
the joystick.
To search for an e-mail in your mailbox, select Options >
Find. Enter the search term, and select OK.
3. After retrieving the e-mails, select Options >
Disconnect to return to the offline mode.
To open an attachment, select Options > Attachments.
4. To view an e-mail message, scroll to it, and press the
Scroll to the attachment, and press the joystick.
31
joystick.
To reply only to the sender ofan e-mail, open the e-mail, delete both the local e-mail messages on the device and
and select Options > Reply > To sender.
the original messages on the server.
To reply to all recipients of an e-mail, open the e-mail,
To delete e-mails from the device only, select Options >
and select Options > Reply > To all.
Delete > Phone only.
To delete e-mail both from the device and from the
remote server, open an e-mail, and select Options >
Delete > Phone and server.
Tip: If you reply to an e-mail that contains
attached files, the attachments are not
included in the reply. If you forward the
received e-mail, attachments are included.
To delete an attachment from an e-mail that you are
sending, select the attachment and Options >
Attachments > Remove.
E-mail folders
If you create subfolders in your IMAP4 mailboxes on a
remote server, you can view and manage these folders
with your device. You can only subscribe to folders in
your IMAP4 mailboxes. Subscribing to folders in a
remote mailbox allows you to view those folders on
your device.
To set the message priority, select Options > Priority
and from the available options.
To call the sender of the e-mail, open the e-mail, and
select Options > Call.
To view folders in your IMAP4 mailbox, establish a
connection, and select Options > E-mail sett. > Retrieval
settings > Folder subscriptions.
To reply to the sender of the e-mail with a text message
or multimedia message, open the e-mail, and select
Options > Create message.
To view a remote folder, select a folder and Options >
Subscribe. Every time you go online, the subscribed
folders are updated. This may take some time if the
folders are large.
To forward an e-mail, open the e-mail, and select
Options > Forward.
Delete messages
To update the list of folders, select a folder and
Options > Update folder list.
To free up memory space on your device, regularly
delete messages from the Inbox and Sent folders, and
delete retrieved e-mail messages.
Write and send e-mail
To delete a message, scroll to it, and press the
backspace key.
To write an e-mail, select Options > Add recipient to
select the recipients' e-mail addresses from the
contacts list, or enter the e-mail addresses in the To
You can select to delete local e-mail messages on the
device and keep the original on the server, or you can
32
field. Use a semicolon to separate entries. Scroll down,
and use the Cc field to copy other recipients, or the
Bcc field to blind copy recipients. In the Subject field,
enter the subject of the e-mail. Enter your e-mail
message in the text area, and select Options > Send.
To attach a file to an e-mail, select Options > Insert and
the attachment you want to add. You can insert images,
sound clips, notes, and other files, such as office files.
•
•
Incoming mail serv. — Enter the IP address or host
name of the server that receives your e-mail.
Accesspoint inuse— Select the Internetaccesspoint
that the device uses for retrieving the e-mail
messages that you receive.
•
•
Default mailbox — Enter a name for the mailbox.
Mailboxtype —Selectthemailboxprotocolthatyour
remote mailbox service provider recommends. The
options are POP3 and IMAP4. This setting can be
selected only once and cannot be changed if you
have saved or exited from the mailbox settings. If
you use the POP3 protocol, e-mail messages are not
updated automatically when you are online. To see
the latest e-mail messages, you must disconnect and
make a new connection to your mailbox.
To set the sending time for an e-mail message, select
Options > Sending options > Send message. Select
Immediately or When conn. avail. if you are working
offline.
E-mail messages are stored in the Outbox before
sending. Unless the e-mail is sent immediately, you can
open the Outbox and suspend and resume sending or
view the e-mail.
•
Security (ports) — Select the security option used to
increase the security of the connection.
•
•
Port — Define a port for connection.
APOP secure login (for POP3 only) — Use with the
POP3 protocol to encrypt the sending of passwords
to the remote e-mail server while connecting to the
mailbox.
E-mail account settings
Select Menu > Messag. > Mailbox.
The settings available for editing may vary. Some
Settings for sent e-mail
settings may be preset by your service provider.
Select Outgoing e-mail and from the following settings:
If you try to edit mailbox settings but have not set up
an e-mail account, the mailbox guide opens and helps
you set up your e-mail account.
•
My e-mail address — Enter the e-mail address given
to you by your service provider. Replies to your
messages are sent to this address.
Settings for the received e-mail
•
•
•
User name — Enter the user name for the e-mail
service.
Select Incoming e-mail and from the following settings:
Password — Enter the password for the e-mail
service.
•
User name — Enter the user name for the e-mail
service.
Outgoing mail serv. — Enter the IP address or host
name of the mail server that sends your e-mail. You
may only be able to use the outgoing server of your
•
Password — Enter the password for the e-mail
service.
33
network operator. Contact your service provider for
more information.
•
•
New e-mail alerts — Select whether you want to
receive the new e-mail indications, a tone and a
note, when new mail is received to the mailbox.
Flash on new e-mails — Select how long you want
the e-mail indicator light to blink when you receive
a new e-mail, or whether you want the indicator
light to blink at all.
•
Accesspoint inuse — Selectthe Internetaccesspoint
that the device uses for sending the e-mail messages
that you send.
•
•
Security (ports) — Select the security option used to
secure the connection to the remote mailbox.
Port — Define a port for connection.
Retrieval settings
User settings
Select Retrieval settings and from the following
Select User settings and from the following settings:
settings:
•
My name — Enter a name to appear before your e-
•
E-mail to retrieve (for POP3 mailboxes only) — Select
whether you want to retrieve only the e-mail header
information such as sender, subject and date, e-mail,
or e-mail with attachments.
mail address when you send e-mail.
•
Reply-to — Select whether you want replies to be
redirected toadifferentaddress. SelectOn, andenter
the e-mail address to which you want to direct the
replies. You can only enter one address.
•
•
•
Retrieval amount — Select the number of e-mails
you want to retrieve from the remote server to your
mailbox.
•
Delete e-mails from — Select whether you want to
delete the e-mails only from the device or from both
the device and the server. Select Always ask if you
want to confirm from where the e-mail should be
deleted every time you delete an e-mail.
IMAP4 folder path (for IMAP4 mailboxes
only) — Define the folder path for folders to be
subscribed.
Folder subscriptions (for IMAP4 mailboxes
only) — Subscribe to other folders in the remote
mailbox and retrieve content from those folders.
•
•
•
Send message — Select to send the e-mail as soon
as possible, to send it the next time you retrieve e-
mail, or to store the e-mailinthe outbox, from where
you can send it later.
Automatic retrieval settings
Send copy to self — Select whether you want to save
a copy of the e-mail to your remote mailbox and to
the address defined in My e-mail address in the
settings for Outgoing e-mail.
Select Automatic retrieval and from the following
settings:
•
E-mail notifications — Select whether you want to
receive notifications when new e-mail is received in
your remote mailbox. Select Always enabled to
always automatically retrieve new e-mail messages
from your remote mailbox, or Only in home net. to
Include signature — Select whether you want to
attach a signature to your e-mail messages.
34
automatically retrieve new e-mail messages from
your remote mailbox only when you are in your
home network and not, for example, traveling.
Retrieval days — Select the days on which e-mails
are retrieved to your device.
2. Enter the text of the message. To use a template,
select Options > Insert > Template.
3. Select Options > Send to send the message.
•
•
•
Retrieval hours — Define the hours between which
the e-mails are retrieved.
Reply to received text messages
To reply to a text message, open the message from the
Inbox. Select Options > Reply. Enter the text of the
message, and select Options > Send.
Retrievalinterval— Select the timeintervalbetween
retrieving new e-mails.
To call the sender of a text message, open the message
Text messages
from the Inbox, and select Options > Call.
Your device supports the sending of text messages
beyond the character limit for a single message. Longer
messages are sent as a series of two or more messages.
Your service provider may charge accordingly.
Characters that use accents or other marks, and
characters from some language options like Chinese,
take up more space limiting the number of characters
that can be sent in a single message.
Text messages on the SIM card
Text messages may be stored on your SIM card. Before
you can view SIM messages, you must copy the
messages to a folder in the device. After copying the
messages to a folder, you can view them in the folder
or delete them from the SIM card.
In the navigation bar, the message length indicator
counts backwards from 160. For example, 10 (2) means
that you can still add 10 characters to send the text as
two messages.
Select Options > SIM messages.
1. Select Options > Mark/Unmark > Mark or Mark all to
mark every message.
2. Select Options > Copy.
3. Select a folder and OK to begin copying.
Write and send text messages
To view SIM card messages, open the folder where you
Select Menu > Messag. > New message > Text
copied the messages, and open a message.
message.
To delete a text message from the SIM card, select the
message, and press the backspace key.
1. In the To field, press the joystick to select recipients
from Contacts, or enter the recipients' mobile phone
numbers manually. If you enter more than one
number, separate the numbers with a semicolon.
35
Text message settings
Picture messages
Note: Picture message function can be used only
if it is supported by your network operator or service
provider. Only devices that offer picture message
features can receive and display picture messages.
Select Options > Settings > Text message.
Define the following:
•
•
•
Message centres — View the available message
centers for your device.
Msg. centre in use — Select a message center to send
the message.
Select Menu > Messag..
Character encoding — Select Reduced support to use
automatic character conversion to another
encoding system when available.
To view a picture message, open the message from the
Inbox folder.
•
•
Receive report — Select Yes if you want that the
network sends you delivery reports on your
messages (network service).
Forward picture messages
Copyright protections may prevent some images, music
Message validity — Select how long the message
(including ringing tones), and other content from being
center resends your message if the first attempt fails copied, modified, transferred or forwarded.
(network service). If the recipient cannot be reached
within the validity period, the message is deleted
from the message center.
1. In the Inbox, open a picture message and select
Options > Forward.
2. In the To field, enter a recipient's number, or press
the joystick to add a recipient from Contacts. If you
enter more than one number, separate the numbers
with a semicolon.
•
Message sent as — Convert the message to another
format, such as Text, Fax, Paging or E-mail. Change
this option only if you are sure that your message
center is able to convert text messages into these
other formats. Contact your network operator.
Preferred conn. — Select the preferred method of
connection when sending text messages from your
device.
3. Enter the text of your message. The text can have
120 characters. To use a template, select Options >
Insert > Template.
•
•
4. To send the message, press the call key.
Reply via same ctr. — Select whether you want the
reply message to be sent using the same text
message center number (network service).
Tip: To remove the picture from the message,
select Options > Remove picture.
36
2. In the Subject field, enter a subject for the message.
To change the fields that are visible, select Options >
Address fields.
Multimedia messages
A multimedia message (MMS) can contain text and
objects such as images, sound clips, or video clips.
3. Enter the text of the message, and select Options >
Insert object to add media objects. You can add
objects such as Image, Sound clip, or Video clip.
Note: Only devices that have compatible features
can receive and display multimedia messages. The
appearance of a message may vary depending on the
receiving device.
messages. If the inserted picture exceeds this limit,
the device may make it smaller so that it can be sent
by MMS.
Before you can send or receive multimedia messages
on your device, you must define the multimedia
message settings. Your device may have recognized the
SIM card provider and automatically configured the
multimedia message settings. If not, contact your
service provider. See "Multimedia message
settings," p. 39.
4. Each slide of your message can contain only one
video or audio clip. To add more slides to your
message, select Options > Insert new > Slide. To
change the order of slides in your message, select
Options > Move.
5. To preview a multimedia message before sending
it, select Options > Preview.
6. Press the joystick to send the multimedia message.
Create and send multimedia
messages
Create presentations
The default setting of the multimedia message service
is generally on.
Select New message > Multimedia message.
1. In the To field, press the joystick to select recipients
from Contacts, or enter the recipients' mobile phone
numbers or e-mail addresses manually.
Select New message > Multimedia message.
Copyright protections may prevent some images, music
(including ringing tones), and other content from being
copied, modified, transferred or forwarded.
2. Select Options > Create presentation and a
presentation template.
1. In the To field, press the joystick to select recipients
from Contacts, or enter the recipients' mobile phone
numbers or e-mail addresses manually.
Tip: A template may define which media
objects you can include in the presentation,
where they appear, and which effects are
displayed between images and slides.
37
3. Scroll to a text area and enter the text.
Receive and reply to multimedia
messages
Important: Multimedia message objects may
contain viruses or otherwise be harmful to your device
or PC. Do not open any attachment if you are not sure
of the trustworthiness of the sender.
4. To insert images, sound, video, or notes in your
presentation, scroll to the corresponding object
area, and select Options > Insert.
Tip: To move between object areas, scroll
up and down.
5. To add slides, select Insert > New slide.
6. Select Options and from the following:
Before you can send or receive multimedia messages
on your device, you must define the multimedia
message settings. Your device may have recognized the
SIM card provider and automatically configured the
multimedia message settings. If not, contact your
service provider. See "Multimedia message
settings," p. 39.
•
Preview — See what your multimedia presentation
looks like when it is opened. Multimedia
presentations may only be viewed in compatible
devices that support presentations. They may
appear different in different devices.
Backgrnd. settings —Selectthebackgroundcolorfor
the presentation and background images for
different slides.
•
•
If you receive multimedia messages containing objects
unsupported by your device, you cannot open them.
Effect settings — Select effects between images or
slides.
1. To reply to a multimedia message, open the
message from the Inbox, and select Options >
Reply.
Creating multimedia presentations is not possible if
MMS creation mode is Restricted. To change MMS
creation mode, select Messag. > Options > Settings >
Multimedia message.
2. Select Options > To sender to reply to the sender
with a multimedia message or Options > Via text
message to reply to the sender with a text message.
The available options may vary.
3. Enter the text of the message, and press the joystick
To send your multimedia presentation, press the
to send it.
joystick.
Tip: To save the message in Drafts without
sending it, select Done.
View presentations
Open the Inbox, scroll to a multimedia message that
contains a presentation, and press the joystick. Scroll to
the presentation, and press the joystick.
38
To pause the presentation, press either selection key
below the display.
Tip: If you receive multimedia messages that
contain media objects your device cannot
open, you may be able to send these objects to
another device such as a computer.
After you pause the presentation or playing finishes,
select Options and from the following:
•
•
Open link — Open a Web link and browse the Web
page.
Multimedia message settings
Activate scrolling — Scroll text or images too large
to fit on the display.
Select Options > Settings > Multimedia message.
•
•
•
Continue — Resume playing the presentation.
Play — Replay the presentation from the start.
Find — Find phone numbers and e-mail or Web
addresses the presentation may contain. You may
usethese numbers andaddresses tomakecalls, send
messages, or create bookmarks, for example.
Define the following settings:
•
•
Image size — Select Small or Large to scale images
in multimedia messages. Select Original to maintain
the original image size of multimedia messages.
MMS creation mode — Select Restricted to have your
device prevent you from including content in
multimedia messages that may not be supported by
the network or the receiving device. To receive
warnings about including such content, select
Guided. To create a multimedia message with no
restrictions on attachment type, select Free. If you
select Restricted, creating multimedia presentations
is not possible.
The available options may vary.
View media objects
Open the Inbox, scroll to a received multimedia
message and press the joystick. Select Options >
Objects.
To view or play a media object, scroll to it, and press the
•
•
Access point in use — Select the default access point
to connect to the multimedia message center. You
may not be able to change the default access point
if it is preset in your device by your service provider.
Multimedia retrieval — Select Always automatic to
always receive multimedia messages automatically,
Auto. in home network to receive notification of a
new multimedia message that you can retrieve from
the message center (for example, when you are
traveling abroad and are outside your home
network), Manual to retrieve multimedia messages
joystick.
Media objects and message attachments may contain
viruses or other harmful software. Do not open any
objects or attachments unless you are sure of the
trustworthiness of the sender.
To save a media object in its corresponding application,
scroll to the object, select Options > Save.
To send a media object to compatible devices, scroll to
it, and select Options > Send.
39
from the message center manually, or Off to prevent your service provider for more information about
receipt of any multimedia messages.
signing up for IM services and costs for services. For
more information on the availability of IM settings,
contact your network operator, service provider, or
dealer.
•
•
•
Allow anon. msgs. — Select whether you want to
receive messages from unknown senders.
Receive adverts — Select whether you want to
receive messages defined as advertisements.
Receive report — Select Yes to have the status of the
sent message to be shown in the log (network
service). Receiving a delivery report of a multimedia
message that has been sent to an e-mail address
may not be possible.
You may receive the settings in a special text message
from the network operator or service provider that
offers the IM service. You must save the settings to
access the service that you want to use. You can also
enter the settings manually.
•
•
Deny report sending — Select Yes to not send
delivery reports from your device for received
multimedia messages.
Connect to an IM server
To converse with an IM user or users, and to view and
edit your IM contacts, you must log into the instant
messaging server. Open IM, and select Options >
Login. Enter your user ID and password, and press the
joystick to log in. You can obtain the user name,
password, and other settings to log in from your service
provider when you register for the service.
Message validity — Select how long the messaging
center tries to send the message (network service).
If the recipient of a message cannot be reached
within the validity period, the message is removed
from the multimedia messaging center. Maximum
time is the maximum amount of time allowed by the
network.
Search IM users or IM groups
Instant messaging
To search for IM users and user IDs, select IM contacts >
Options > New IM contact > Search. You can search by
User's name, User ID, Phone number, and E-mail
address.
Select Menu > Connect. > IM.
Instant messaging (IM) (network service) allows you to
converse with other people using instant messages and
join discussion forums (IM groups) with specific topics.
Various service providers maintain IM servers that you
can log in to after you register to an IM service. Service
providers may differ in their support of features.
To search for IM groups and group IDs, select IM
groups > Options > Search. You can search by Group
name, Topic, and Members (user ID).
If IM is not available from your wirelessservice provider,
40
it may not appear in the menu of your device. Contact
To send automatic replies to incoming messages, select
Options > Set auto reply on. You can still receive
messages.
Conversations with a single IM
user
The Conversations view shows a list of the individual
conversation participants with whom you have an
ongoing conversation. Ongoing conversations are
automatically closed when you exit IM.
IM groups
The IM groups view shows a list of the IM groups that
you have saved or to which you are currently joined.
To view a conversation, scroll to a participant, and press
IM groups is available only if you logged into an IM
server when you opened the IM application, and the
server supports IM groups.
the joystick.
To continue the conversation, enter your message, and
press the joystick.
To create an IM group, select Options > Create new
To return to the conversations list without closing the
conversation, select Back. To close the conversation,
select Options > End conversation.
group.
To join an IM group or to continue a group conversation,
scroll to the group, and press the joystick. Enter a
message, and press the call key to send it.
To start a new conversation, select Options > New
conversation. You can start a new conversation with a
different contact while you are inside another active
conversation. However, you cannot have two active
conversations with the same contact.
To join an IM group that is not on the list, but for which
you know the group ID, select Options > Join new
group.
To leave the IM group, select Options > Leave IM
To insert an image to an instant message, select
Options > Send image, and select the image you want
to send.
group.
To remove an IM group, press the backspace key.
To save a conversation participant to your IM contacts,
Ban from groups
select Options > Add to IM contacts.
Scroll to the IM group, and select Options > Group >
To save a conversation, while in the conversation view,
select Options > Record chat. The conversation is saved
as a text file that can be opened and viewed in the
Notes application.
Settings > Banned list.
To prevent IM users from joining the group, select
Options > Add to banned list and from the following:
•
From IM contacts — Ban one or several of your IM
41
contacts.
•
Enter user ID — Enter the ID of the IM user.
•
•
•
•
New contact list — Create a contact list for a specific
group of IM contacts.
To allow a banned user to join the group, select
Reload users' availab. — Update the online status of
your IM contacts.
Options > Remove.
Blocking options — Prevent or allow the reception
of messages from the contact.
IM contacts
Login — Connect to an instant messaging server if
you did not log in when you opened the application.
Logout — Disconnect from the IM server.
Settings — Edit instant messaging application or
server settings.
When login to an IM service is complete, your contact
list for the service provider is retrieved automatically. If
your contact list is not available, wait a few minutes and
try to retrieve your contacts list manually.
•
•
Tip: The online status of your IM contacts is
shown by an indicator next to the contact
name.
The available options may vary.
To delete an IM contact, press the backspace key.
Blocked contacts
To create an IM contact card, select Options > New IM
contact. Enter the user ID and a nickname, and select
Done. The user ID can be up to 50 characters, and the
IM service provider may require the user ID to be in the
[email protected] format. The nickname is
optional.
Select IM contacts > Options > Blocking options > View
blocked list.
To find a blocked IM user, enter the first letters of the
user's name. Matching names appear in a list.
To allow receiving messages from a blocked IM user,
To view a different list of your IM contacts, select
select Options > Unblock.
Options > Change contact list.
To prevent receiving messages from other IM users,
select Options > Block new contacts. Select the IM user
from your IM contacts, or enter the user ID.
Scroll to an IM contact, select Options and from the
following:
•
Open conversation — Start or continue instant
messaging with the contact.
Settings
•
•
Contact details — View the contact card.
Editing options — Edit or delete the contact card,
move it to another contact list, or receive a note
when the contact's online status changes.
Belongs to groups — See the IM groups the contact
has joined.
Select Options > Settings > IM settings.
Select from the following settings:
•
•
Use screen name — To change the name that
42
identifies you in IM groups, select Yes.
•
•
•
Allow messages from — Select to receive instant
messages from all other IM users, your IM contacts
only, or not to receive messages at all.
Select Manual to connect to the server manually at
any time.
Allow invitations from — Select to receive
invitations to IM groups from all IM users, your IM
contacts only, or not to receive invitations at all.
Msg. scrolling speed — To decrease or increase the
speed at which new messages are displayed, scroll
left or right.
Special messages
Your device can receive many kinds of messages that
contain data:
•
•
•
Operator logo — To save the logo, select Options >
•
•
•
Sort IM contacts — Select to list your IM contacts
alphabetically or by their online status.
Save.
Ringing tone — To save a ring tone, select Options >
Save.
Availabil. reloading — To update the online status
of your IM contacts automatically, select Automatic.
Offline contacts — Select if IM contacts with an
offline status are shown in the IM contacts list.
Configuration message — You may receive settings
from your network operator, service provider, or
company information management department in
a configuration message. To accept the settings,
open the message, and select Options > Save all.
E-mail notification — The note tells you how many
new e-mails you have in your remote mailbox. An
extended notification may list more detailed
information.
The settings available forediting may vary. Contact your
service provider for more information.
•
IM server settings
Select Options > Settings > Server settings.
Scroll to the following options, and press the joystick to
configure your IM server:
Send service commands
•
•
Servers — Add new, edit, or delete servers.
Default server — Change the server to which your
device automatically logs into, scroll to the desired
server, and press the joystick.
Send a service request message to your service provider
and request activation for certain network services.
To send a service request to your service provider, select
Options > Service command. Enter the service request
as a text message, and select Options > Send.
•
IM login type — To establish a connection between
your device and the default server automatically,
select Automatic. Select Auto. in home network to
automate the connection when in your home
network. Select On app. start-up to connect to the
server when you open the messaging application.
43
Make calls
When the device is locked, calls still may be possible to Press the call key to view up to 20 numbers that you last
the official emergency number programmed into your
called or attempted to call. Scroll to the desired number
or name, and press the call key to dial the number. See
"Log," p. 46.
device.
In the offline profile, you may need to enter the lock
code and change the device to a calling profile before
making any call, including a call to an emergency
number.
Use the volume keys to adjust the volume of an active
call.
When you open the cover of the device during a call, the
loudspeaker is activated.
To make and receive calls, the device must be switched
on, the device must have a valid SIM card installed, and
you must be located in a service area of the cellular
network. The GPRS connection is put on hold during
voice calls unless the network supports dual transfer
mode or you have a USIM card and are within the
coverage of a UMTS network.
To call your voice mailbox (network service) in standby
mode, press and hold 1, or press 1 then the call key.
Speed dial
Speed dialing allows you to make a call by pressing and
holding a number key.
Enter the phone number, including the area code, and
press the call key. If you enter an incorrect character,
press the backspace key.
Before using speed dialing, select Menu > Tools >
Settings > Call > Speed dialling > On.
Tip: For international calls, enter the +
character thatreplaces theinternationalaccess
code, and enter the country code, area code
(omit the leading 0, if necessary), and phone
number.
To assign a number key to a phone number, select
Menu > Tools > Spd. dial. Scroll to the number key (2 -
9) on the screen, and select Options > Assign. Select the
desired number from the Contacts directory.
To end the call or cancel the call attempt, press the end
To remove the phone number assigned to a number
key, scroll to the speed dialing key, and select Options >
Remove.
To change a phone number assigned to a number key,
scroll to the speed dialing key, and select Options >
Change.
key.
To make a call using the saved contacts, press
Contacts in standby mode. Enter the first letters of the
name, scroll to the name, and press the call key. See
"Contacts," p. 54.
44
•
All voice calls, All data and vid. calls, or All fax
calls. — Divert all incoming voice, data and video,
or fax calls.
Answer a call
•
•
If busy — Divert incoming calls when you have
an active call.
Note: The actual invoice for calls and services
from your service provider may vary, depending on
network features, rounding off for billing, taxes, and so
forth.
If not answered — Divert incoming calls after
your device rings for a specified period of time.
Define the time you let the device ring before
diverting the call in the Delay time: field.
If out of reach — Divert calls when the device is
switched off or out of network coverage.
If not available — Activate the last three settings
at the same time. This option diverts calls if your
device is busy, not answered, or out of reach.
To answer a call, press the call key.
To reject the call, press the end key.
•
•
To mute a ringing tone instead of answering a call,
select Silence.
To answer a new call during a call when the Call
waiting function is activated, press the call key. The first
call is put on hold. To end the active call, press the end
key.
3. Select Activate.
To check the current diverting status, scroll to the
diverting option, and select Options > Check status.
To stop diverting voice calls, scroll to the diverting
Divert calls
option, and select Options > Cancel.
Select Menu > Tools > Settings > Call divert.
Divert incoming calls to your voice mailbox or to
another phone number. For details, contact yourservice
provider.
Call barring
Call barring and call diverting cannot be active at the
same time.
1. Select a call type from the following:
When calls are barred, calls still may be possible to
•
•
Voice calls — Incoming voice calls.
Data and video calls — Incoming data and video
calls.
certain official emergency numbers.
Select Menu > Tools > Settings > Call barring.
•
Fax calls — Incoming fax calls.
You can bar the calls that can be made or received with
the device (network service). To change the settings,
you need the barring password from your service
provider. Call barring affects all calls, including data
calls.
2. Select one of the following call diverting options:
45
To bar calls, select Cellular call barring and select from
the following options:
if the recipient has a compatible mobile phone with a
video camera. A video call can only be made between
two parties.
•
Outgoing calls — Prevent making voice calls with
your device.
Warning: Do not hold the device near your ear
when the loudspeaker is in use, because the volume
may be extremely loud.
•
•
Incoming calls — Bar incoming calls.
International calls — Prevent calling to foreign
countries or regions.
•
•
Incoming if abroad — Bar incoming calls when
outside your home country.
Select the still image to be sent in Tools > Settings >
Call > Image in video call.
Intern. except home — Prevent calls to foreign
countries or regions, but to allow calls to your home
country.
To make a video call, enter the phone number or select
the recipient of the call from Contacts, and select
Options > Call > Video call. You cannot convert the video
call to a normal voice call.
To check the status of voice call barrings, scroll to the
barring option, and select Options > Check status.
During the call, select Options and from the following:
To stop all voice call barrings, scroll to a barring option,
•
•
•
Audio — Talk to the recipient of the call.
Use video — See video without audio.
Loudsp. — Select to use the loudspeaker for
receiving audio.
and select Options > Cancel all barrings.
Net call barring
•
Handset — Mute the loudspeaker and use the
handset.
To bar net calls, select Menu > Tools > Settings > Call
barring > Internet call barring.
To reject net calls from anonymous callers, select
Log
Anonymous calls > On.
Select Menu > Log.
In the Log, you can view information about the
Video calls
communication history of the device.
To be able to make a video call, you must be within
coverage of a UMTS network. For availability of and
subscription tovideo call services, contact yournetwork
operator or service provider. While talking, you can
send a still image to the recipient's compatible mobile
phone and see a real-time video sent by the recipient,
To view the logs for recent voice calls, their
approximate duration, and packed data connections,
select Recent calls, Call duration, or Packet data; and
press the joystick.
46
To sort the events by type or direction, scroll right to
open the general log, and select Options > Filter. Scroll
to a filter type, and press the joystick. Select the type or
direction, and press the joystick.
towards the microphone, and do not cover the
loudspeaker with your hands.
Phone calls always take priority over push to talk.
Before you can use push to talk, you must define the
push to talk access point and push to talk settings. You
may receive the settings in a special text message from
the service provider that offers the push to talk service.
To set the time how long all communication events are
held in the log, select Options > Settings > Log
duration, an option, and OK.
To clear missed and received calls and dialed numbers,
User settings
select Recent calls > Options > Clear recent calls.
Select Options > Settings > User settings.
Define the following:
Push to talk
•
Incoming PTT calls — Select Notify if you want to see
a notification of incoming calls. Select Auto-accept if
you want push to talk calls to be answered
automatically. Select Not allowed if you want push
to talk calls to be rejected automatically.
PTT call alert tone — Select Set by profile if you want
the incoming call alert setting for push to talk to
follow your profile settings. If your profile is silent,
you are not available to others using push to talk,
except for callback requests.
Select Menu > Connect. > PTT.
Push to talk (PTT) (network service) provides direct
voice communication connected with the push of a key.
With push to talk, you can use your device as you would
use a walkie-talkie.
•
You can use push to talk to have a conversation with
one person or with a group of people, or to join a
channel. A channel is like a chat room: you can call the
channel to see if anyone is online. The channel call does
not alert the other participants; the participants just
join the channel and start speaking with each other.
•
•
Callback request tone — Define the ringing tone for
callback requests.
Application start-up — Select if you want to log in to
the push to talk service when you switch on your
device.
In push to talk communication, one person talks while
the other participants listen through the built-in
loudspeaker. Participants take turns responding to
each other. Because only one participant can talk at a
time, the maximum duration of a speech turn is limited.
For detailsofthe speechturndurationforyournetwork,
contact your network operator or service provider.
•
•
Default nickname — Enter your default nickname
(20 characters maximum) that is displayed to other
users.
Show my PTT address — Define if you want callers
to see your push to talk address. You can let all callers
see the address, show the address only to one-to-
Remember to hold the device in front of you during a
47
push to talk call so you can see the display. Speak
one callers or channel participants, or hide the
address from all callers.
When the Ringing type setting of your device is set to
Beep once or Silent, or there is an ongoing phone call,
you cannot make or receive push to talk calls.
•
Show my login status — Define whether your login
to the push to talk server is shown or hidden from
other users.
Push to talk calls
Connection settings
Warning: Do not hold the device near your ear
when the loudspeaker is in use, because the volume
may be extremely loud.
Select Options > Settings > Connection settings.
Define the following:
•
•
•
Domain — Enter the domain name obtained from
Select Options > PTT contacts.
your service provider.
To make a push to talk call, select one or several
contacts from the list, and press the voice key.
Remember to hold the device in front of you during a
push to talk call so you can see the display. The display
informs you when it is your turn to speak. Speak
towards the microphone, and do not cover the
loudspeaker with your hands. Press and hold the voice
key the entire time you are talking. When you have
finished talking, release the key.
Access point name — Select the push to talk access
point.
Server address — Enter the IP address or domain
name of the push to talk server obtained from your
service provider.
•
•
User name — Enter your user name obtained from
your service provider.
Password—Enter apassword, if required, to log into
the push to talk service. The password is provided by
the service provider.
To end the push to talk call, press the end key.
When you receive a push to talk call, press the call key
to answer the call or the end key to dismiss the call.
Log in to push to talk service
If you have set Application start-up on in User
settings, push to talk automatically logs in to theservice
when started. If not, you must log in manually.
Callback requests
To send a callback request, select Options > PTT
contacts, scroll to the desired contact, and select
Options > Send callback request.
To log in to a push to talk service, select Options >
Settings > Connection settings, and enter your User
name, Password, Domain, Server address, and Access
point name. Select Options > Switch PTT on.
To answer a callback request, select Show to open the
callback request. To make a push to talk call to the
sender, press the voice key.
48
Contacts view
Register PTT channels
To view, add, modify, delete, or call contacts, select
To register a channel to the push to talk service, select
Options > PTT contacts. A list of names from your device Options > Register.
Contacts application is displayed with information
To edit the channel details, select Options > Edit.
about their login status.
To call a selected contact, select Options > Talk 1 to 1.
To make a group call, select Options > Make PTT group
call.
Join a channel
To join a channel, select Options > PTT channels. Select
the channel you want to talk to, and press the voice key.
Remember to hold the device in front of you during a
push to talk call so you can see the display. The display
informs you when it is your turn to speak. Speak
towards the microphone, and do not cover the
loudspeaker with your hands. Press and hold the voice
key the entire time you are talking. When you have
finished talking, release the key.
To send the contact a request to call you, select
Options > Send callback request.
Create a channel
A channel is like a chat room: you can call the channel
to see if anyone is online. The channel call does not alert
the other participants; the participants just join the
channel and start speaking with each other.
To switch between channels during multiple calls,
select Swap. The active channel is highlighted.
To create a channel, select Options > New channel >
Create new.
To view the currently active participants in the channel,
select Options > Active members.
Select Options and define the following:
•
•
•
Channel name — Write the channel name.
Channel privacy — Select Private or Public.
Nickname in channel — Enter your nickname (20
characters maximum) that is displayed to other
users.
To invite a participant to a channel, select Options >
Send invitation.
Push to talk log
•
Channel thumbnail — Insert a picture that describes
To open the push to talk log, select Options > PTT log.
The log shows the date, time, duration, and other
details of your push to talk calls.
the channel.
To delete a channel, press the backspace key.
When you log in to push to talk, push to talk
automatically connects to the channels that were active
when the application was last closed.
49
The availability of the net call service may vary
according to your country or sales area.
Exit push to talk
Select Options > Exit. Select Yes to log out and close the
service. Press No if you want to keep the application
active on the background.
Define the net call settings
Before you can make net calls, you need to define the
net call settings. After you have defined the net call
settings with these instructions, your device logs in to
the net call service automatically, when you select
Menu > Connect. > Internet tel..
Net calls
With the net call service (network service), you can
make and receive calls over the Internet.
First: define a SIP profile
Your device supports voice calls over the Internet
(Internet calls). Your device attempts emergency calls
primarily over cellular networks. If an emergency call
using cellular networks is not successful, then your
device attempts an emergency call through your
Internet call provider. Due to the established nature of
cellular telephony, you should use cellular networks for
emergency calls, if possible. If you have cellular network
coverage available, please make sure that your cellular
phone is switched on and ready to make calls before
you attempt an emergency call. The capability for an
emergency call using Internet telephony depends on
the availability of a WLAN network and your Internet
call provider's implementation of emergency call
capabilities. Contact your Internet call provider to check
the Internet telephony emergency call capability.
1. Select Menu > Tools > Settings > Connection > SIP
settings > Options > Add new, and enter the
required information. You must define all available
SIP settings, but ensure that Registration is set to
Always on. Contact your net call provider for the
correct information.
2. Select Proxy server, and set Transport type to Auto.
3. Select Back until you return to the Connection menu.
Second: define a net call profile
1. Select Internet tel. settings > Options > New
profile. Enter a name for the profile, and select the
SIP profile you just created.
2. Select Back until you return to the main menu.
Third: select a preferred net call profile (optional)
VoIP (voice over Internet protocol) technology is a set
of protocols that facilitate phone calls over an IP
network, such as the Internet. VoIP phone calls can be
established between computers, between mobile
phones, and between a VoIP device and a traditional
telephone. To make or receive a VoIP call, your device
must be within WLAN coverage, for example.
If you select a preferred net call profile, Internet tel.
automatically uses this network profile to connect to
the net call service.
1. Select Menu > Connect. > Internet tel..
2. Select Preferred profile, and the net call profile you
50
just created.
3. Select Back until you return to the main menu.
•
•
Configure service — to configure new services. This
option is shown only if there are services that have
not been configured.
Tip: You can also use manual login to the net
call service. Use the same settings instructions
as with automatic login, but ensure that
Registration is set to When needed and
Transport type is set to UDP or TCP. With
manual login, you need to manually select the
network used in the net call service.
Save network — to save the network you are
currently connected to. The previously saved
networks are marked with a star icon on the list of
connection networks. This option is shown only if
you are connected to an unsaved wireless LAN
network.
•
•
Use hidden network — to connect to a net call
service using a hidden wireless LAN network.
Refresh — to manually refresh the list of connection
networks. Use this option, if your wireless LAN
network is not shown on the list. The list is also
refreshed automatically every 15 seconds.
Connect to the net call service
To make or receive a net call, your device must be
connected to a net call service. Select Menu > Connect. >
Internet tel..
If you have selected automatic login, your device
connects to the net call service automatically. If you
have selected to login to the service manually, choose
an available connection network from the list and press
Select to connect to the net call service. The saved
networks, which are marked with a star icon, are shown
first on the list. If you want to stop the connection from
establishing, select Cancel.
The available options may vary.
Your device can be connected only to one wireless LAN
access point at a time. If you use two or more net call
services, which use the same access point, your device
may be connectedtomultiple services at the same time.
The service used for outgoing net calls is shown in the
view, where the connection networks are listed, and
can be changed by selecting Change service.
Select Options and from the following:
After you have successfully connected to a service, you
can save the used wireless LAN network as a known
access point.
•
Connect to service — to establish a connection to a
service, when there is a net call service and suitable
connection network available.
•
•
Disconnect from serv. — to end the connection to
the net call service.
Connect using a shortcut
Change service — to choose the net call service for
outgoing calls, if the device is connected to more
than one service. This option is shown only if there
is more than one configured service available.
You may have a shortcut for Internet tel. in the active
standby or you can add a shortcut if it is not available.
See "Standby mode settings," p. 95. By using the
shortcut, you can register manually, if a net call service
51
and an access point are available. If you are already
connected to a net call service, the device asks if you
want to disconnect from the service.
Service settings
Select Menu > Connect. > Internet tel. > Options >
Settings > Settings:
Select Login type to view or change the way Internet
tel. connects to the net call service. Select from the
following:
Make net calls
If you set Internet call as the preferred call type, and
your device is connected to a net call service, calls are
made as net calls as default.
•
Automatic — Login to the net call service
automatically. When a known network is found, the
device connects to the net call service automatically.
If you use the automatic login type for wireless LAN
networks, the device periodically scans for wireless
LAN networks, which increases the demand on
battery power and reduces the battery life.
To set the preferred call type for outgoing calls, select
Menu > Connect. > Internet tel. > Options > Settings >
Preferred call type > Cellular or Internet call.
You can make a net call from all applications where you
can make a regular voice call.
•
Manual — Login to the net call service manually.
To make a net call in the standby mode, enter the phone
number or Internet address and press the call key.
Select Saved conn. networks to view the connection
networks you have saved for the net call service or the
connection networks, which are recognized by the net
call service. These networks are used for automatic
login and are marked with a star icon on the list of
connection networks. To remove a connection network
from the service, select Options > Remove.
To make a net call to an address that does not start with
a digit, press any number key when the device is in the
standby mode, then press the blue function key to clear
the display and to switch the device from number mode
to letter mode. Write the address and press the call key.
You can also make a net call from Contacts and Log. To
make a call from Contacts, select Menu > Contacts, and
scroll to the desired contact. Select Options > Call >
Internet call.
Select Edit service settings to open the service-specific
settings. This option is only available, if a service-
specific software plug-in has been installed in the
device.
To make a call from Log, select Menu > Log > Recent
calls and Missed calls, Recvd. calls or Dialled nos., and
scroll to the desired contact. Select Options > Call >
Internet call.
Voice commands
Select Menu > Tools > Voice cm..
Use voice commands to make phone calls and to launch
52
applications, profiles, or other functions on the device.
The device creates a voice tag for the entries in the
contacts list and for the functions designated in the
Voice cm. application. When a voice command is
spoken, the device compares the spoken words to the
voice tag in the device.
To add more applications to the list, select Options >
New application.
To change the voice command of an application, scroll
to the application, and select Options > Change
command. Type the new voice command, and select
OK.
Make a call
The voice tag for a contact is the name or nickname that
is saved on the contact card in Contacts. To listen to the
voice tag, open a contact card, and select Options > Play
voice tag.
Change profiles
The device creates a voice tag for each profile. To set on
a profile using a voice command, press and hold the
voice key, and say the name of the profile.
1. To make a call using a voice command, press and
To change the voice command, scroll to the desired
profile, and select Profiles > Options > Change
command.
hold the voice key.
2. When you hear the tone or see the visual display,
clearly speak the name saved on the contact card.
3. The device plays a synthesized voice tag for the
recognized contact in the selected device language,
and displays the name and number. After a timeout,
the device dials the number. If the recognized
contact was not correct, select Next to view a list of
other matches or Quit to cancel dialing.
Voice command settings
To switch off the synthesizer that plays recognized
voice commands in the selected device language, select
Options > Settings > Synthesiser > Off.
To reset voice recognition learning when the main user
of the device has changed, select Reset voice adapts..
Launch an application
The device creates voice tags for the applications listed
in the Voice cm. application.
To launch an application using a voice command, press
and hold the voice key, and clearly speak the voice
command. If the recognized application was not
correct, select Next to view a list of other matches or
Quit to cancel.
53
Contacts
Select Menu > Contacts.
2. Enter a name for the group or use the default name,
and select OK.
Manage all of your contact information, such as phone
numbers and addresses. Add a personal ringing tone,
voice tag, or a thumbnail image to a contact. Send
contact information to compatible devices or receive
contact information as business cards from compatible
devices, and add them to your own list of contacts.
3. Open the group, and select Options > Add
members.
4. Scroll to each contact you want to add to the group,
and press the joystick to mark it.
5. Select OK to add all marked contacts to the group.
To add a contact, select Options > New contact. Enter
The following options are available when you select
the contact information, and select Done.
Options in the contact groups view:
To edit information in a contact card, scroll to the
contact, and select Options > Edit. Select from the
following options:
•
•
PTT options — Make a push to talk call either to
an individual or to a group, or send a callback
request.
•
Add thumbnail — Add a thumbnail image that will
display when a contact calls you. The image must be
previously saved to your device or memory card.
Remove thumbnail — Remove the image from the
contact card.
Open — Open the contact group and view the
group members.
•
•
•
•
•
Create message — Send a message.
New group — Create a new contact group.
Delete — Delete a contact group.
Rename — Rename the contact group.
Ringingtone— Assign a ringingtone toa contact
group.
•
•
•
•
Add detail — Add fields of information to a contact
card, such as Job title.
Delete detail — Delete any details that you added to
a contact card.
•
•
Contacts info — View the information for a
contact group.
Edit label — Edit the field names of the contact card.
Settings — Set the name display settings for
contact group members.
Manage contact groups
Create a contact group so that you can send text or e-
mail messages to several recipients at the same time.
54
1. Scroll to the right, and select Options > New group.
Select Options > SIM contacts > SIM directory to see the
names and numbers stored on the SIM card. In SIM
directory you can add, edit, or copy numbers to
Contacts, and you can make calls.
Manage default
information
Assign a default number or address to a contact so you
can easily call or send a message to the default number
or address, even if several numbers or addresses are
saved to that contact.
Select ringing tones for
contacts
To change default information for a contact, open the
contact, and select Options > Defaults. Select the
number or address you want to set as a default, and
select Assign.
Select a ringing tone for a contact or contact group. If
the caller's phone number is sent with the call and your
device recognizes the number, the ringing tone plays
when the contact calls you.
The default number or address is underlined in the
contact.
To select a ringing tone for a contact or contact group,
open the contact or contact group, and select Options >
Ringing tone. A list of ringing tones opens. Select the
ringing tone you want to use.
Copy contacts between SIM
and device memory
To remove the ringing tone, select Default tone from
the list of ringing tones.
For availability and information on using SIM card
services, contact your SIM card vendor. This may be the
service provider, network operator, or other vendor.
Business cards
To copy contacts from a SIM card to device memory,
select Options > SIM contacts > SIM directory to open
the SIM directory. Mark the contacts you want to copy,
or select Mark all to copy all contacts. Select Options >
Copy to Contacts.
To copy contacts from the device memory to a SIM card,
select Options > Copy to SIM direct.. Mark the contacts
you want to copy, or select Mark all to copy all contacts.
Select Options > Copy to SIM direct..
Select Menu > Contacts.
You can send, receive, view, and save contact cards as
business cards in vCard or Nokia Compact Business Card
format.
You can send business cards to compatible devices
using SMS, MMS, or e-mail, or an infrared or Bluetooth
connection.
To send a business card, select the contact card from
55
the contacts list, and select Options > Send. Select Via
text message, Via multimedia, Via e-mail, Via
Bluetooth, or Via infrared. Enter the phone number or
address, or add a recipient from the contacts list. Select
Options > Send. Ifyou selectSMSas thesendingmethod,
contact cards are sent without images.
To view a received business card, select Open from the
displayed notification, or open the message from the
inbox folder in Messag..
To save a business card, select Options > Save business
card when the incoming message appears on the
device.
To save a received business card, select Options > Save
business card.
To delete a received business card, select Options >
Delete.
56
Calendar
To open and edit an existing entry, scroll to the entry,
and select Options > Open. Edit the details in the various
fields.
Select Menu > Organiser > Calendar.
In Calendar, you can create and view scheduled events
and appointments. You can also set alarms for calendar
entries.
Tip: When you edit or delete a repeated entry,
choosehowyou wantthechangetotakeeffect.
If you select All calendar entries deleted, all
repeated entries are deleted. If you select
Delete entry, only the current entry is deleted.
You can synchronize your calendar data with a
compatible computer using Nokia PC Suite. For
information on synchronization, see the PC Suite guide.
Create calendar entries
To-do
You can create four types of calendar entries:
You can create and maintain a task or list of tasks that
must be done by a certain day. Each task can be
assigned a due date, and an alarm.
•
•
Meeting entries have a specific date and time.
Memo entries are related to the whole day but not
to a specific time of the day. Memo entries do not
appear in the weekly time schedule view.
To open the list of to-do notes, select Options > To-do
view.
•
Anniversary entries remind you of birthdays and
special dates. They refer to a certain day but not a
specific time of the day. Anniversary entries are
repeated every year.
To add a to-do note, select Options > New entry > To-
do. Start to write the task in the Subject field. You can
set a due date for the task, create an alarm for it, and
specify a priority. The priority icons are ( ! ) High and ( - )
Low. There is no icon for Normal.
•
To-do note entries remind you of a task that has a
due date but not a specific time of the day.
To mark a task as completed, scroll to the task in the to-
To create a calendar entry, scroll to a date, and select
Options > New entry. Select an entry type. Available
settings for meeting, memo, anniversary, and to-do
entries vary.
do list, and select Options > Mark as done.
To restore a task, scroll to it in the todo list, and select
Options > Mark as not done.
57
Calendar views
To switch between the different calendar views, select
Options in any calendar view. Select a type of view from
the list.
To set the default calendar view, select Options >
Settings > Default view > Month view , Week view, Day
view, or To-do view.
To view a specific date in the calendar view, select
Options > Go to date. Enter the date, and select OK.
Add a received calendar
entry to your calendar
You can receive a calendar entry as an attachment to a
multimedia or e-mail message.
To add a received calendar entry to your calendar, open
the calendar entry attachment in the message, and
select Options > Save to Calendar. The entry is added to
your default calendar.
58
Clock
Select Menu > Clock.
Alarm clock
To change the clock type, select Options > Settings >
If the alarm time is reached while the device is switched
off, the device switches itself on and starts sounding the
alarm tone. If you select Stop, the device asks whether
you want to activate the device for calls. Select No to
switch off the device or Yes to make and receive calls.
Do not select Yes when wireless phone use may cause
interference or danger.
Clock type > Analogue or Digital.
Date and time settings
To change the date and time, their display formats,
alarm tone, and to define whether you want to use
automatic time update, select Options > Settings and
from the following:
To set an alarm, select Options > Set alarm. Enter the
•
•
•
•
Time — Enter the time, and select OK.
alarm time, and select OK.
Time zone — Enter the time zone, and select OK.
Date — Enter the date, and select OK.
To view and change alarms, select Options > Reset
alarm.
Date format — Change how the date is displayed.
Scroll to the desired format, and select OK.
Date separator — Change the symbol that separates
days, months, and years. Scroll to the symbol you
want, and select OK.
To remove an alarm, select Options > Remove alarm.
•
•
•
Time format — Select 24-hour or 12-hour.
Time separator — Select the symbol that separates
hours and minutes.
•
•
Clock type — Select Analogue or Digital.
Clock alarm tone — Select the tone that you want to
use for the alarm clock.
•
Network operator time — Update time, date, and
time zone information automatically (network
service). Select Auto-update to activate. This service
may not be available in all networks.
59
Connectivity
(including ringing tones), and other content from being require another. To connect to the Internet over GPRS,
copied, modified, transferred or forwarded.
your device may have predefined, default Internet
access point settings.
Your device offers several options to connect to the
Internet, a corporate intranet, or to another device or
PC. Wireless methods include wireless LAN, Bluetooth,
and infrared. Your device supports a wired solution
with a USB (Universal Serial Bus) cable connection for
Nokia PC Suite or IP passthrough. Your device also
allows you to communicate using net calls (Voice over
IP), push to talk, instant messaging (chat), and modem-
based connections.
access points may be configured automatically based
on the service provider information in your SIM card.
You can also receive the access points settings in a
message from your service provider. This might reduce
the number of settings you need to enter yourself.
The available options may vary. Some or all access
points may be preset for your device by your service
provider. You may not be able to add, edit, or delete
access points.
Dev. mgr.—See "Remote configuration network
service," p. 84.
Internet tel.—See "Net calls," p. 50.
PTT—See "Push to talk," p. 47.
Contact your service provider and e-mail service
provider for more information on access points and
their settings.
IM—See "Instant messaging," p. 40.
Sync—See "Data synchronization," p. 84.
See "Connection settings," p. 97.
Set up an Internet access point for
packet data (GPRS)
Internet access points
An access point is where your device connects to a
network. To use e-mail and multimedia services or to
connect to the Internet and browse web pages, you
must first define Internet access points for these
services. You may need to set up several Internet access
points, depending on the sites you want to access. For
example, browsing the Web may require one access
1. Select Menu > Tools > Settings > Connection > Access
points.
2. Select Options > New access point. To use an
existing access point as a basis for the new one,
select Use existing settings. To start with an empty
access point, select Use default settings.
60
3. Define the following settings.
Set up an Internet access point for
wireless LAN
•
Connection name — Enter a descriptive name for
the connection.
•
•
Data bearer — Select Packet data.
1. Select Menu > Tools > Settings > Connection > Access
Access point name — Enter the name for the
access point. The name is usually provided by
your service provider or network operator.
User name — Enter your user name if required
by the service provider. User names are often
case-sensitive and provided by your service
provider.
points.
2. Select Options > New access point. To use an
existing access point as a basis for the new one,
select Use existing settings. To start with an empty
access point, select Use default settings.
•
•
3. Define the following settings.
Prompt password — Select Yes to enter your
password each time you log into a server or No
to save the password in your device memory and
automate the login.
•
Connection name — Enter a descriptive name for
the connection.
•
•
Data bearer — Select Wireless LAN.
WLAN netw. name — To enter the service set
identifier (SSID), that is, the name that identifies
the specific wireless LAN, select Enter manually.
To select the network from the wireless LANs in
range, select Search for netw..
•
•
•
Password — Enter your password if required by
the service provider. The password is often case-
sensitive provided by the service provider.
Authentication — Select Secure to always send
your password encrypted or Normal to send your
password encrypted when possible.
•
•
Network status — Select Hidden if the network
you are connecting to is hidden, or Public if it is
not hidden.
Homepage — Enter the Web address of the page
you want to display as a home page when you
use this access point.
WLAN netw. mode — If you select
Infrastructure, devices can communicate with
each other and with wired LAN devices through
a wireless LAN access point. If you select Ad-hoc,
devices can send and receive data directly with
each other, and no wireless LAN access point is
needed.
4. After defining the settings, select Options >
Advanced settings to define the advanced settings
or Back to save the settings and exit.
For information on the advanced settings, see the
extended user guide on the Web.
•
WLAN security mode — You must select the same
security mode that is used in the wireless LAN
access point. If you select WEP (wired equivalent
privacy), 802.1x, or WPA2 (Wi-Fi protected
access), you must also configure the relevant
61
additional settings. See the extended user guide normally connect to your device with the data cable,
on the Web or the device help for more
information.
press the joystick.
Select from the following:
•
•
WLAN security sett. — Edit the security settings
for the selected WLAN security mode.
Homepage — Enter the Web address of the page
you want to display as a home page when you
use this access point.
•
Ask on connection — Select whether you want to be
asked for the device type every time you connect the
data cable to your device.
•
•
PC Suite — Connect the PC Suite to your device with
the data cable, and use your device as a modem.
Data transfer — Access and transfer data such as
music or image files from your computer using the
data cable connection. To use the Data transfer
mode, make sure that you have not selected USB as
a connection type in the Manage connections
settings in Nokia PC Suite. Insert a memory card to
your device, connect the device to a compatible
computer with the USB data cable, and select Data
transfer when the device asks which mode is used.
In this mode, your device acts as a mass storage
device and you can see it as a removable hard drive
in your computer. The device will switch into the
Offline profile if this is selected. End the connection
from the PC (for example, from an Unplug or Eject
Hardware wizard in Windows) to avoid damaging
the memory card. After you end the connection, the
device returns to the profile in which it was before
using the data transfer mode.
The settings available for editing may vary.
Wireless LAN
Select Menu > Tools > Settings > Connection > Wireless
LAN.
To have your device show wireless LAN availability,
select Show availability.
Tip: You can also scan for networks in range.
If you need to configure the MAC address of your device
to a WLAN router, enter *#62209526# on the device
keypad. TheMAC addressis shown on the devicedisplay.
Cable connection
•
IP passthrough — Select an access point through
which to transfer data using the Internet protocol.
Install the USB data cable driver to your PC before you
use a cable connection. You can use the Data transfer
without installing the USB data cable drivers.
To save your selection, select Back.
Select Menu > Connect. > Data cbl..
Using a USB data cable, you can connect your device to
a compatible PC . Connect the USB data cable to the
bottom of the device. To change the device type you
62
Start using Bluetooth
Bluetooth
Select Menu > Connect. > Bluetooth.
There may be restrictions on using Bluetooth
technology in some locations. Check with your local
authorities or service provider.
To activate Bluetooth, press the blue function key and
the Ctrl key simultaneously. To deactivate, press the
blue function key and the Ctrl key again. If you use this
shortcut to activate Bluetooth, you will not be asked to
name your device.
Features using Bluetooth technology, or allowing such
features to run in the background while using other
features, increase the demand on battery power and
reduces the battery life.
1. When you activate Bluetooth for the first time, you
are asked to give a name to your device. Give your
device a unique name to make it easy to recognize
if there are several Bluetooth devices in the vicinity.
This device is compliant with Bluetooth Specification
1.2 supporting the following profiles: Generic Access
Profile, Serial Port Profile, Dial-up Networking Profile,
Headset Profile, Handsfree Profile, Generic Object
Exchange Profile, Object Push Profile, File Transfer
Profile, SIM Access Profile, and Basic Imaging Profile. To
ensure interoperability between other devices
supporting Bluetooth technology, use Nokia approved
enhancements for this model. Check with the
manufacturers of other devices to determine their
compatibility with this device.
2. Select Bluetooth > On.
3. Select My phone's visibility > Shown to all.
Your device and the name you entered can now be seen
by other users with devices using Bluetooth
technology.
Settings
Bluetooth technology enables wireless connections
between electronic devices within a range of 10 meters
(33 feet). A Bluetooth connection can be used to send
images, videos, texts, business cards, calendar notes, or
to connect wirelessly to devices using Bluetooth
technology, such as computers.
Define the following settings:
•
Bluetooth — Select On to be able to connect to
another compatible device using Bluetooth
connectivity.
•
My phone's visibility — Select Shown to all to allow
other devices using Bluetooth technology to find
your device when you have set Bluetooth > On. To
prevent other devices from finding your device,
select Hidden. Even if you select Hidden, paired
devices can still detect your device.
Since devices using Bluetooth technology
communicate using radio waves, your device and the
other devices do not need to be in direct line-of-sight.
The two devices only need to be within a maximum of
10 meters of each other, although the connection can
be subject to interference from obstructions such as
walls or from other electronic devices.
•
My phone's name — Enter a name for your device.
The name is visible to other devices that search for
63
devices using Bluetooth technology. The maximum
length of the name is 30 characters.
3. Select the device with which you want to connect,
and press the joystick to set up the connection. If
the other device requires pairing before data can be
transmitted, you are asked to enter a passcode.
•
Remote SIM mode — Select On to enable another
device, such as a compatible car kit enhancement, to
use the SIM card in your device to connect to the
network. See "SIM access profile," p. 65.
4. When the connectionhas been established, Sending
data is shown.
If Bluetooth was turned off as a result of entering
The Sent folder in Messag. does not store messages sent
using Bluetooth connectivity.
Offline profile, you must re-enable Bluetooth manually.
Security tips
Bluetooth connectivity indicators
When you are not using Bluetooth connectivity, select
Bluetooth is active.
Bluetooth > Off or My phone's visibility > Hidden.
Do not pair with an unknown device.
When the icon is blinking, your device is trying to
connect to the other device. When the icon is shown
continuously, the Bluetooth connection is active.
Send data
Several Bluetooth connections can be active at a time.
For example, if you are connected to a headset, you can
also transfer files to another compatible device at the
same time.
Pair devices
Select Menu > Connect. > Bluetooth, and scroll right to
open the Paired devices page.
1. Open the application where the item you want to
Before pairing, create your own passcode (1-16 digits),
and agree with the user of the other device to use the
same code. Devices that do not have a user interface
have a fixed passcode. You need the passcode only
when you connect the devices for the first time. After
pairing, it is possible to authorize the connection. See
"Authorize a device," p. 65. Pairing and authorizing
the connection makes connecting quicker and easier,
as you do not have to accept a connection between
paired devices every time you establish the connection.
send is stored.
2. Select the item, and select Options > Send > Via
Bluetooth. The device searches for other devices
using Bluetooth technology within range and lists
them.
Tip: If you have sent data using Bluetooth
before, a list of the previous search results
is displayed. To search for more Bluetooth
devices, select More devices.
64
The passcode for remote SIM accessmusthave 16 digits.
1. Select Options > New paired device. The device
•
•
Set as authorised — Connections between your
device and the other device can be made without
your knowledge. No separate acceptance or
authorization is needed. Use this status for your own
devices, such as your compatible headset or PC, or
devices that belong to someone you trust.
Set as unauthorised — Connection requests fromthe
other device must be accepted separately every
time.
starts to search for Bluetooth devices within range.
Tip: If you have sent data using Bluetooth
before, a list of the previous search results
is displayed. To search for more Bluetooth
devices, select More devices.
2. Select the device with which you want to pair, and
enter the passcode. The same passcode must be
entered to the other device as well.
3. Select Yes to make the connection between your
device and the other device automatic or No to
confirm the connection manually every time a
connection attempt is made. After pairing, the
device is saved to the paired devices page.
To give a nickname to a paired device that is only
displayed in your device, scroll to the device with which
you have paired, and select Options > Assign short
name.
Receive data
If you want to receive data using Bluetooth, select
Bluetooth > On and My phone's visibility > Shown to
all. When you receive data through Bluetooth
connectivity, a tone sounds, and you are asked if you
want to accept the message. If you accept, the message
is placed in the Inbox folder in Messag.
Tip: You can access the files in the device or on
the memory card using a compatible accessory
that supports the File Transfer Profile Client
service (for example, a laptop computer).
To delete a pairing, select the device whose pairing you
want to delete and Options > Delete. To delete all
pairings, select Options > Delete all.
Tip: If you are currently connected to a device
and cancel the pairing with that device, pairing
is removed immediately, and the connection is
switched off.
SIM access profile
When the wireless device is in the remote SIM mode,
you can only use a compatibleconnectedenhancement,
such as a car kit, to make or receive calls. Your wireless
device will not make any calls, except to the emergency
numbers programmed into your device, while in this
mode. To make calls from your device, you must first
leave the remote SIM mode. If the device has been
locked, enter the code to unlock it first.
Authorize a device
If you trust a paired device, you can allow it to connect
automatically to your device. You can select from the
following options:
65
With the SIM access profile, you can access the SIM card
of your device from a compatible car kit device. This
way, you do not need a separate SIM card to access SIM
card data and connect to the GSM network.
device can be made without separate acceptance or
authorization. If you select No, connection requests
from this device must be accepted separately every
time.
To use the SIM access profile, you need the following:
Tip: If you have already accessed the SIM card
from the car kit with the active user profile, the
car kit searches automatically for a device with
the SIM card. If it finds your device, and
•
Compatible car kit device that supports Bluetooth
wireless technology
•
Valid SIM card in your device
automatic authorization is activated, the car
device automatically connects to the GSM
network when you switch on the car ignition.
For more information about car kit devices and
compatibility with your device, see www.nokia.com
and your car kit user guide.
When you activate the remote SIM access profile, you
can use applications on your device that do not need
network or SIM services.
Manage the SIM access profile
1. Select Menu > Connect. > Bluetooth to activate
Bluetooth connectivity in your device.
To end the remote SIM access connection from your
device, select Menu > Connect. > Bluetooth > Remote
SIM mode > Off.
2. To enable remote SIM access, scroll to Remote SIM
mode, and press the joystick.
3. Activate Bluetooth in the car kit device.
4. Use your car kit device to start a search for
compatible devices. For instructions, see the user
guide of your car kit device.
Infrared
Do not point the IR (infrared) beam at anyone's eye or
allow it to interfere with other IR devices. This device is
a Class 1 laser product.
5. Select your device from the list of compatible
devices.
Use infrared to connect two devices and transfer data
between them. With infrared, you can transfer data
such as business cards, calendar notes, and media files
with a compatible device.
6. To pair the devices, enter the Bluetooth passcode
shown on the display of the car kit device to your
device.
7. Authorize the car kit device. Select Menu >
Connect. > Bluetooth, and scroll to the Paired
devices page. Scroll to the car kit device, and enter
the Bluetooth passcode. When the device asks to
make the connection automatic, select Yes.
Connections between your device and the car kit
Send and receive data
1. Ensure that the infrared ports of the devices face
each other. The positioning of the devices is more
important than angle or distance.
66
2. Select Menu > Connect. > Infrared, and press the
You must subscribe to the GPRS service. For availability
joystick to turn on infrared on your device. Turn on and subscription to GPRS, contact your network
infrared on the other device.
operator or service provider.
3. Wait a few seconds until an infrared connection is
Enhanced GPRS (EGPRS) is similar to GPRS, but it enables
faster connection. For more information on the
availability of EGPRS and data transfer speed, contact
your network operator or service provider. Note that
when you have selected GPRS as a data bearer, the
device uses EGPRS instead of GPRS if this is available in
the network.
established.
4. To send, locate the desired file in an application or
the file manager, and select Options > Send > Via
infrared.
If data transfer is not started within 1 minute after the
activation of the infrared port, the connection is
cancelled and must be started again.
During a voice call, you cannot establish a GPRS
connection, and any existing GPRS connection is put on
hold unless the network supports dual transfer mode.
All items received through infrared are placed in the
Inbox folder in Messag..
Positioning devices away from each other breaks a
connection, but the infrared light beam remains active
on your device until it is deactivated.
UMTS
UMTS (Universal Mobile Telecommunications System) is
a 3G mobile communication system. Besides voice and
data, UMTS enables audio and video delivery to wireless
devices.
Data connections
Your device can automatically switch between the GSM
and UMTS networks.
Packet data
To select which network to use, select Menu > Tools >
Settings > Network and the network in Network
mode. If you want the device to switch between the
networks automatically, select Dual mode.
GPRS (general packet radio service) enables wireless
access for mobile phones to data networks (network
service). GPRS uses packet data technology where
information is sent in short bursts of data over the
mobile network. The benefit of sending data in packets
is that the network is occupied only when sending or
receiving data. As GPRS uses the network efficiently, it
allows for quick data connection set-up and fast data
transmission speeds.
The GSM network is indicated with
, the UMTS
network with
.
When you use your device in GSM and UMTS networks,
multiple data connections can be active at the same
time, and access points can share a data connection. In
the UMTS network, data connections remain active
67
during voice calls. You can, for example, browse the
Web faster than previously possible while
simultaneously speaking on the phone.
•
The infrastructure operating mode allows two kinds
of communication: wireless devices communicate
with each other through a wireless LAN access point
or wireless devices communicate with a wired LAN
device through a wireless LAN access point. The
advantage of the infrastructure operating mode is
that you can have more control over network
connections because they pass through an access
point. A wireless device can access the services that
are available in a regular wired LAN: company
database, e-mail, the Internet, and other network
resources, for example.
Wireless local area network
(WLAN)
Some places, like France, have restrictions on the use of
wireless LAN. Check with your local authorities for more
information.
Features using wireless LAN, or allowing such features
to run in the background while using other features,
increase the demand on battery power and reduce the
battery life.
•
In the ad hoc operating mode you can send data to
and receive it from other devices with compatible
wireless LAN support , for example, to be printed.
These functions may require an additional third
party application to work. No wireless LAN access
point is required. Simply make the necessary
configurations and start communicating. Ad hoc
networking is easy to set up, but communication is
limited to devices that are within range and support
compatible wireless LAN technology.
This device can detect and connect to a wireless local
area network.
If you move the device to another location within the
wireless LAN and out of range of a wireless LAN access
point, the roaming functionality can automatically
connect your device to another access point that
belongs to the same network. As long as you remain
within range of access points that belong to the same
network, your device can stay connected to the
network.
Connection manager
Select Menu > Connect. > Conn. mgr..
Tip: A wireless LAN connection is established
when you create a data connection using a
wireless LAN Internet access point. The active
wireless LAN connection is ended when you
end the data connection.
To view the status of data connections or end
connections, select Act. data conn..
To search for wireless LANs available within range,
select Availab. WLAN.
Your device enables different types of communication
in a wireless LAN. The two operating modes are
infrastructure and ad hoc.
68
To create an Internet access point in a network, select
View and end active connections
Options > Define access point.
Note: The actual time invoiced for calls by your
service provider may vary, depending on network
features, rounding off for billing, and so forth.
Modem
Select Menu > Connect. > Modem.
In the active connections view, you can see the open
data connections: data calls, packet data connections,
and wireless LAN connections.
Together with a compatible computer, you can use your
device as a modem to connect to the Web.
Before you can use your device as a modem
To view detailed information about network
connections, select the connection from the list and
Options > Details. The type of information shown
depends on the connection type.
•
You must subscribe to the appropriate network
services from your service provider or Internet
service provider.
•
•
•
You need a compatible computer with a USB data
To end a network connection, select the connection
cable, Bluetooth, or infrared connectivity.
from the list and Options > Disconnect.
You must have Nokia PC Suite installed on your
computer.
To end all active network connections simultaneously,
select Options > Disconnect all.
You must have the appropriate drivers installed on
your computer. You may need to install drivers for
your cable connection, and you may need to install
or update Bluetooth or infrared drivers. After you
have installed Nokia PC Suite, follow the instructions
on the computer display to install the drivers and
connect your device to the computer.
To view the details of a network, press the joystick.
Search for wireless LAN
To search for wireless LANs available within range,
select Menu > Connect. > Conn. mgr. > Availab. WLAN. A
list of found networks is displayed.
After you have installed Nokia PC Suite and the
appropriate cable drivers, start Nokia PC Suite on your
computer. Select Connect to the Internet, and follow the
instructions on the computer display.
The available wireless LAN view shows a list of wireless
LANs within range, their network mode (infrastructure
or ad-hoc), signal strength indicator and network
encryption indicators, and if your device has an active
connection with the network.
You may not be able to use some of the other
communication features when the device is used as a
modem.
To view the details of a network, press the joystick.
69
Mobile VPN
Email data roaming
Select Menu > Tools > Settings > Connection > VPN.
Select Menu > Tools > Settings > Connection > Access
point groups.
The Nokia mobile virtual private network (VPN) client
creates a secure connection to compatible corporate
Intranet and services, such as e-mail. Your device
Your device allows roaming between wireless access
technologies, such as WLAN and GPRS, for e-mail. For
connects from a mobile network, through the Internet, example, you can start an e-mail session at home and
to a corporate VPN gateway that acts as a front door to continue the session on your way to work. While your
the compatible corporate network. VPN client uses IP
Security (IPSec) technology. IPSec is a framework of
session continues uninterrupted, your handheld device
switches from WLAN to GPRS and back to WLAN when
open standards for supporting secure exchange of data you arrive at your workplace.
over IP networks.
VPN policies define the method used by VPN client and
Access point groups
a VPN gateway to authenticate each other, and the
To create an access point group, select Access point
encryption algorithms that they use to help protect the
confidentiality of data. Contact your corporation for a
VPN policy.
groups > Options > New group. In the Group name field,
enter a name for the group. Define in the Conn.
switching field whether to show the connection
switching process on the display of your device. Choose
and edit the access points that belong to this group in
the Access points section.
To use VPN with an application, the application must be
associated with a VPN access point. A VPN access point
is made up of an Internet access point and a VPN policy.
To manage VPN, select VPN management > Options >
To remove an access point in an access point group,
Open and from the following options:
select the access point and Options > Remove.
•
•
VPN policies — Install, view, and update VPN policies.
VPN policy servers — Edit the connection settings of
VPN policy servers from which you can install and
update VPN policies.
•
VPN log — View the log for your VPN policy
installations, updates and synchronizations, and
other VPN connections.
70
Web
Select Menu > Web (network service).
You can also enter the Internet access point settings
manually. See "Internet access points," p. 60.
Web is one of the two browsers in your device. With
Web, you can browse regular Web sites. These pages
use the extensible hypertext markup language (XHTML)
or hypertext markup language (HTML). If you want to
browse WAP pages, use Menu > Media > Services. Both
of the browsers use the same bookmarks. The links in
your received messages open in the Services browser.
Browse the Web
To browse the Web, select a bookmark, and press the
joystick. You can also enter the Web address, and press
the joystick. Use only services that you trust and that
offer adequate security and protection against harmful
software.
Check the availability of services, pricing, and fees with
your network operator or service provider. Service
providers will also give you instructions on how to use
their services.
Tip: When you start to enter the address,
addresses of pages you have previously visited
that match your input are displayed. To open a
page, scroll to the address, and press the
joystick.
Access points
To browse the Web, you need to configure Internet
access point settings. If you are using a data call or a
GPRS connection, your wireless network must support
data calls or GPRS, and the data service must be
activated for your SIM card. Your device might have
configured the Internet access point settings
To open a Web link, scroll to it and press the joystick.
On a Web page, new links appear underlined in blue and
previously visited links in purple. Images that act as
links have a blue border around them.
Addresses of the pages you visit are saved in the Auto.
automatically based on your SIM card. If not, contact
bookmarks folder.
your service provider for the correct settings.
Keyboard shortcuts:
Tip: You may receive the Internet access point
settings from your service provider as a special
text message or from the network operator's
or service provider's Web pages.
•
•
•
•
Press 1 to open your Bookmarks.
press 2 to find text.
Press 3 to return to the previous page.
Press 5 to switch between your open browser
71
windows.
•
•
Press 8 to open page overview.
Download items
Press 9 to go to a different Web page.
Important: Only install and use applications and
other software from sources that offer adequate
security and protection against harmful software.
Bookmarks
Your device may have some bookmarks loaded for sites
not affiliated with Nokia. Nokia does not warrant or
endorse these sites. If you choose to access them, you
should take the same precautions, for security or
content, as you would with any Internet site.
You can downloaddifferent items suchasringingtones,
images, operator logos, themes, and video clips. To
download an item, scroll to it, and press the joystick.
These items can be provided free, or you can purchase
them. Downloaded items are handled by the respective
applications in your device.
To view a bookmarked Web page, scroll to the
bookmark, and press the joystick.
When you start a download, a list of ongoing, paused,
and completed downloads from the current browsing
session is displayed. To view the list, you can also select
Options > Tools > Downloads. In the list, scroll to an
item, and select Options to pause, resume, or cancel
ongoing downloads; or open, save, or delete completed
downloads.
To browse other Web pages, select Options >
Navigation options > Go to web address, enter the page
address, and select Go to.
To delete a bookmark, scroll to it, and press the
backspace key.
To add a bookmark, select Menu > Web > Options >
Bookmark manager > Add bookmark. Scroll to Name to
enter a descriptive name for the bookmark, Address to
enter the Web page address, Access point to change the
access point to connect to the Web page, and User
name or Password to enter your user name and
password, if required by the service provider. To save
the bookmark, select Back.
To purchase items:
1. To download the item, scroll to the link, and press
the joystick.
2. Select the appropriate option to purchase the item.
3. Carefully read all the information provided. To
continue the download, select Accept. To cancel the
download, select Cancel.
End a connection
To end the connection and view the browser page
offline, select Options > Advanced options >
72
Disconnect; or to end the connection and close the
Web settings
browser, select Options > Exit.
Select Menu > Web > Options > Settings.
Define the following settings:
Clear the cache
•
•
•
•
Access point — Scroll to the access point to connect
A cache is a memory location that is used to store data
temporarily. If you have tried to access or have accessed
confidential information requiring passwords, empty
the cache after each use. The information or services
you have accessed are stored in the cache.
to Web pages, and press the joystick.
Load imgs. & sounds — Select No to loadpages faster
when browsing by not loading the images on them.
Default encoding — Select the correct character
encoding for your language.
To clear the cache, select Options > Advanced options >
Auto. bookmarks — Select On to save Web page
addresses that you visit automatically in the Auto.
bookmarks folder. To hide the folder, select Hide
folder.
Clear cache.
News feeds and blogs
•
•
Screen size — Select Full screen to use the whole
display area for viewing Web pages. You can press
the left selection key to open Options and use the
available options while browsing in full screen
mode.
Select Menu > Web > Web feeds.
Feeds are xml files in various Web pages that usually
contain headlines and articles, often about recent news
or other topics. You can subscribe to interesting feeds
on Web pages. Select Options > Subscribe.
Homepage — Select the page that you want to
appear as your homepage. Select Default to use the
access point homepage, User defined to enter the
homepage address, or Use current page to use the
currently open Web page.
Tip: Blog is a shortening of Weblog, which is a
continuously updated Web diary . Often the
author's personality is an important factor in
the blog.
•
•
•
Mini map — Select whether you want to see an
overview of the page as a miniature on top of the
page you are viewing.
To download a feed or blog, scroll to it, and press the
joystick.
History list — Select whether you want to see
miniatures of the pages you have visited when you
want to go back in your browsing history.
Cookies — Select to allow or reject the sending and
receiving of cookies. Cookies are info the network
server collects about your visits to various Web
pages. They are necessary if you shop on the Web
To add a feed or blog, select Options > Manage feed >
New feed, and enter the information.
To edit a feed or blog, scroll to a feed, select Options >
Manage feed > Edit, and modify the information.
73
(for example, to retain the items you buy until you
reach the cashier page). However, the information
may be misused (for example, you may receive
unwanted advertisements in your device).
Java/ECMA script — Some Web pages may include
program commands that affect the appearance of
the page or interaction between the page and its
browsers. To deny the use of such scripts, select
Disabled (for example, if you have trouble
downloading).
Tip: To start a connection, press and hold 0 in
the standby mode.
•
•
•
Security warnings — Select Show or Hide to see or
hide the security warnings you may receive during
browsing.
Block pop-ups — Select whether you want to allow
pop-ups. Some pop-ups may be necessary (for
example, smaller windows where you write e-mails
in Web-based mail systems), but they may also
contain unwanted advertising.
Services
Select Menu > Media > Services (network service).
Services is one of the two browsers in your device. With
Services, you can browse WAP pages that have been
designed specially for mobile devices. For example,
operators may have WAP pages for mobile devices. To
browse regular Web pages, use the other browser in
Menu > Web.
Check the availability of services, pricing, and fees with
your network operator or service provider. Service
providers will also give you instructions on how to use
their services.
74
Office applications
Select Menu > Office.
To open an existing document, browse for the folder
and document, and press the joystick. To read the
document, select the middle view.
Some office applications are not available in all
languages.
Opening a large file may not be possible or it may take
a while.
Tip: To open a recently used document, select
Options > Most recent files, select the
document, and press the joystick.
Note that in addition to the Documents, Sheet, and
Presentation applications, you can also download the
Quickoffice application from Nokia Catalogs.
To create a new document, select Options > New file.
Select Blank to create a new document without using a
template or Use template to create a document based
on an existing template.
Remember to save the file you are working with, before
switching off your device.
To read a document, select the middle view and
Options. You can browse for different types of objects
in the document, zoom in or out, switch between full
and normal screen views, or view objects, such as
images. You can also search for textand edit application
settings such as zooming, scrolling, and handling of
invisible characters.
File manager
With File mgr., you can manage the contents and
properties of files and folders. You can open, create,
move, copy, rename, and search for files and folders.
Copyright protection may prevent sending some files.
View objects in a document
Documents
To view all objects, such as tables, comments,
workbooks, and video clips in their place in the
document, select the middle view and Options >
Browse > Pages and objects.
You can open, edit, and save documents created with
Microsoft Word for Windows versions 97 or later. Note
that not all features and formatting of the original files
are supported.
To open a table or comment, scroll to the object or its
Select Menu > Office > Docum..
icon, and press the joystick twice.
75
To open an image or go to a hyperlink or reference,
scroll to the object, and press the joystick three times.
chapters or all subchapters. If there are objects in the
document, select Options > Display objects or Display
headings to switch between object list and chapter
heading views.
Edit documents
Tip: To open a selected chapter in the normal
view, scroll to the chapter, and press the
joystick.
To be able to edit a document, you must activate the
edit mode: select the middle view and Options > Edit
document. Select Options > Format, and the
appropriate formatting option. For example, you can
add bold, italic, and underline formatting, change the
font size and color, and add bullets. You can also modify
the paragraph settings such as text alignment and line
spacing.
Preview the page layout
To preview the page layout, select the view on the right
and Options.
Define the following options:
Tip: To cancel an action in the editing mode,
select Options > Undo.
•
Normal view — Show the current open page in
normal view.
To insert a new object to the document, select
Options > Insert object. Scroll to the desired object type,
and select Options > Insert. If you want to insert a new
document, workbook, or presentation, select Insert
new. To insert an existing document, workbook,
presentation, select Insert existing.
To format the style settings of a paragraph, select
Options > Format > Style. Select the style you want to
formatand Options > Edit. Select Newstyle to add anew
style. In the style editing view, select Options >
Format, and the style you want. You can modifythefont,
formatting, paragraph, bullet, and border styles.
•
•
Pan and zoom — Zoom the page layout view.
View — Select Full screen or Normal screen to switch
between full screen and normal views.
To zoom the page layout, select the view on the right,
scroll to the desired page, and select Options > Pan and
zoom. A black selection frame appears above the page
layout, showing the area to zoom. Select the area and
Options > Zoom.
Select from the following options:
•
In or Out — Select In to zoom in one step in the
selected area, or Out to zoom out one step in the
selected area.
•
•
Fit to screen — Adjust the zoom level to fit the page
to the screen width.
View document structure
Ratio — Edit the zoom level, enter the zoom ratio
between 10 and 999, and select OK.
To view the document outline, select the left view.
76
Select Options > Expand or Collapse to show only main
Find text
Sheet
To find a piece of text from the document, select
Options > Find, enter the text in theFind: field, and press
the joystick.
Select Menu > Office > Sheet.
To open an existing workbook, browse for the folder
where the file is saved, and press the joystick.
To change search options such as case sensitivity and
To create a new workbook, select Options > New file.
Select Blank to create a new file without using any
template or Use template to create a file based on an
existing template. Select the worksheet in the outline
view, and press the joystick to open the file.
search direction, select Options > Search options.
Table editor
You can view tables created in applications, like
documents and MS Word.
Work with worksheets
To view a table in a file, scroll to the file so that a dotted
line appears around it, and press the joystick.
To insert data into cells, open the worksheet view. Use
the joystick to move to the cell, and select Options >
Show cell field > Edit cell field. An upper part editing
field opens. Enter the data, and select Done to finish
editing.
To change the selected cell, scroll up, down, left or right.
If the selected cell does not fit into visible area, pressing
the joystick pans the whole content first before the cell
changes.
To select a range of cells, press and hold the shift key
To edit the text in a cell, select the cell, and press the
while you scroll right.
joystick. To end editing, press the joystick again.
To modify the worksheet view, select Options > View.
Select Options and from the following options:
Select from the following options:
•
•
•
•
•
Zoom — Zoom the table view in, out and to edit a
zoom ratio.
•
Pan worksheet — Define the size of the visible area
Format — Modify the font style and formatting,
paragraphs, bullets, and borders.
Cell size — Change the size of the cells, rows and
columns.
of the whole worksheet.
•
•
Full screen — Switch to the full screen view.
Hide headers — Hide header field and release more
space for the worksheet grid.
Cells — Select option to insert, delete, merge or
separate cells.
•
Hide gridlines — Hide gridlines.
To change the font and number formatting, borders,
and alignments, select Options > Format and the
appropriate option.
Copy table — Copy the text of the whole table to the
clipboard.
77
Work with cells
Create and modify charts
When you change the information on a worksheet, the
chart is updated simultaneously.
To insert cells, select the area where you want to insert
new cells and Options > Cells > Insert. You can insert
cells above (Shift cells down) or to the left (Shift cells
right) of the selected range. If you select only one cell,
only one new cell is inserted. If you select a range of
cells, a corresponding range of blank cells is inserted.
You can also insert a new row or column.
To open a chart, open the outline view, select the
worksheet and chart, and press the joystick. If charts
are not visible, select Options > Expand.
To create a new chart, select the worksheet cells that
contain the information you want to include in the
chart and Options > Insert > Chart. To change the
general appearance of an existing chart, open a chart
view. Select Options > View > Chart. You can change the
name of the chart and define the cell area. You can
change the type of the chart, and make the chart two
or three-dimensional or change the color of the
background and axis. Scroll right to add a title to the
chart and axis.
To format a chart in more detail, open a chart view.
Select Options > View and the object you want to edit.
You can change the series, X-axis, and Y-axis settings
(such as the tick marks of either axis).
To delete cells, rows, or columns, select the items you
want to delete and Options > Cells > Delete. You can
delete an entire row or column. If you select Shift cells
left, the selected cells are deleted, and the cells right of
the selected cells are shifted left. If you select Shift cells
up, the cells below the deleted cells are shifted up.
To insert a function into a cell, select a cell. Select
Options > Insert > Function and a function from the list.
For example, MIN finds the lowest value in the numeric
contents of a selected range of cells, AVERAGE calculates
the average of the values, and SUM adds the values
together. Once you have selected a function, press the
joystick. The function is inserted into the selected cell.
On the worksheet, enter the cells you want to include
in the function inside the brackets, and press the
joystick.
Presentation
You can open, view, edit, and save presentations
created with Microsoft PowerPoint 97 or later. You can
also create new presentations. Note that not all
features and formatting of the original files are
supported.
Tip: Before inserting a function, verify that
Options > Show cell field > Edit grid is active
and thatthe selectedcellis empty orstarts with
=.
Select Menu > Office > Presentat..
To open an existing presentation, browse for the folder
78
and file, and press the joystick.
To create a new presentation, select Options > New
file. Select Blank to create a new presentation without
using a template or Use template to create a
presentation based on an existing template.
Layout view
To open the layout view, select the view in the middle.
To enable or disable the visibility of charts, comments,
tables, images, and shapes, select Options > Settings,
scroll to the settings item, and press the joystick.
Outline view
The outline view is used to navigate through long
presentation documents. The view enables fast vertical
scrolling, rearranging of slides, and editing of objects.
To open the outline view, scroll to the view on the left.
In the outline view, each slide has its own main level
entry. Under the main level there is a sublevel for each
text field and object.
To view the slide content, select Options > Expand. To
hide the content, select Options > Collapse. To collapse
or expand all entries, select Options > View > Collapse
all or Expand all.
View slide shows
To start a slide show, select Options > Presentation.
Select from the following options:
•
•
Manual — Move from one slide to another manually.
Slide show — Move from one slide to another
manually, or use the automatic slide switching. You
must specify the duration for a slide.
•
•
Manual looped — The slide show continues from the
beginning when the last slide of a presentation has
been shown.
Looped slide show — The slide show continues
automatically from the beginning when the last
slide of a presentation has been shown.
To move between slides in a slide show, scroll up to
display a previous slide and down to display the next
slide.
To end the slide show, press the right selection key.
To change the order of slides, scroll to the slide you
want to move, and select Options > Slide > Move. Scroll
up and down to select a new location, and select OK.
Notes view
Work with different views
In the notes view, you can read notes that are attached
to slides in the presentation. You can also add your own
notes.
The presentation application consists of different views
that help you when reading and creating presentations.
To open the notes view, scroll to the view on the right.
Each slide has its own main level entry. Under the main
level there is a sublevel for notes. If notes are not visible,
To switch between the different views, scroll right and
left with the joystick.
79
select Options > View > Expand all. To edit a note, scroll
•
Undo, Redo — Withdraw the latest modifications.
to the note, and press the joystick.
Find text in a presentation
Edit presentations
To find a piece of text from in the presentation, select
To edit a presentation, open the layout view, and select any of the views. Select Options > Find, enter the text in
Options > Edit slide. Scroll right or down with the
joystick to move forward and left or up to move
backward. Select Options.
the Find: field, and press the joystick.
To change the search option for case and whole words,
select Options > Search options.
Define the following options:
•
Add title, Add subtitle, Add text, Insert table, Insert
image — Add a new text or object inside the selected
area.
Screen export
You can show the screen of the device to an audience
with a compatible data projector, or other compatible
projection system. The screen content is transferred to
the data projector using, for example, a Bluetooth
connection.
•
•
Edit text, Edit table, Edit document, Edit
workbook — Edit the selected object.
Edit object — Select Move to move the object, scroll
to the item, and press the joystick. Select Resize to
change the size of the object. Scroll right and left to
change the horizontal size of the object and up and
down to change the vertical size. To accept the
changes, press the joystick. Select Rotate to rotate
the object. Scroll right to rotate the object clockwise
and left to rotate counterclockwise. To accept the
changes, press the joystick. Select Properties to edit
text, line, border, or background properties of the
object.
Select Menu > Office > Screen export.
To be able to show screen content with a compatible
data projector, you must install the drivers of the data
projector. For more information, check with the data
projector manufacturer or its representative.
Not all applications support this feature. You can start
the external viewer in two ways: from the Office folder
or inside an application that supports it.
•
•
Object — Delete, copy, paste, or add a link to the
selected object.
Object position — Change the layered position of the
selected object in the presentation: up, down, front,
or back.
Show screen content
To show screen content with a data projector, open the
screen export application, and select Options > Select
device. Inthelistofavailabledevices, scrollto the device
•
Insert — Add a new text box, image, shape, table, or
comment to the presentation.
80
you want to use, and select OK. Select Options >
To change the page layout before printing, select
Options > Printing options > Page setup and from the
following tabs:
Enable to show screen content.
To hide the screen content, select Options > Hide. The
screen exporter application is moved to the
background.
•
•
•
Paper size — Change the paper size or orientation
and customize the height and width.
Margins — Change the size of the left, right, top, or
bottom margins.
To stop showing screen content, select Options >
Disable.
Header — The maximum length of the header is 128
characters. You can set the distance from the header
to the text and choose to include the header on the
first page of the document.
Print
Print a message or file from the device. Preview a print
job, define page layout options, select a printer, or print
to a file.
•
Footer — The maximum length of the footer is 128
characters. You can set the distance from the footer
to the text.
Before you print, make sure that your device is properly
To add or delete a printer, select Menu > Office >
connected to the printer.
Printers > Options > Add or Delete.
To print a message or file, open the message or file, and
select Options > Printing options.
Define the following options:
•
•
Printer — Select an available printer from the list.
Print — Select All pages, Even pages, or Odd pages
as the print range.
•
•
•
Print range — Select All pages in range, Current
page, or Defined pages as the page range.
Number of copies — Select the number of copies to
print.
Print to file — Select to print to a file and determine
the location for the file.
You may not be able to print all messages, such as
multimedia messages or other special message types.
To preview a file or message before you print, select
81
Options > Printing options > Preview.
Organiser
Select Menu > Organiser.
Thecalculatorperformsoperationsintheordertheyare
entered. The result of the calculation remains in the
editor field and can be used as the first number of a new
calculation.
To save the results of a calculation, select Options >
Memory > Save. The saved result replaces the previously
stored number in memory.
Organiser includes tools that help you organize and
manage the details of different events in your personal
and business life.
Calendar—See "Calendar," p. 57.
Notes
To retrieve the results ofa calculation frommemoryand
use them in a calculation, select Options > Memory >
Recall.
Select Menu > Organiser > Notes.
You can create and send notes to other compatible
devices, and save plain text files (.txt format) that you
receive to Notes.
To view the last saved result, select Options > Last
result.
Exiting the calculator application or turning off the
device does not clear the memory. You can recall the
last saved result the next time you open the calculator
application.
To write a new note, select Options > New note, write
the text and press Done.
Calculator
Converter
Note: This calculator has limited accuracy and is
Select Menu > Organiser > Converter.
designed for simple calculations.
The converter has limited accuracy, androunding errors
Select Menu > Organiser > Calculator.
may occur.
To make a calculation, enter the first number of the
calculation. Scroll to and select a function such as add
or subtract from the function map. Enter the second
number of the calculation, and select =. To add a
decimal point, press #.
Convert measurements
1. Scroll to the Type field, and select Options >
Conversion type to open a list of measures. Scroll to
the measure you want to use, and select OK.
82
2. Scroll to the first Unit field, and select Options >
Change currency. Select the unit from which you
want to convert, and select OK. Scroll to the next
Unit field, and select the unit to which you want to
convert.
After you have inserted all the necessary exchange
rates, you can make currency conversions.
Voice mailbox
3. Scroll to the first Amount field, and enter the value
Select Menu > Organiser > Voice mail.
you want to convert. The other Amount field
When you open the voice mailbox application for the
first time, you are asked to enter the number of your
voice mailbox. To change the number, select Options >
Change number. To call the number, select Options >
Call voice mailbox.
changes automatically to show the converted value.
Set base currency and exchange
rate
Note: When you change base currency, you must
enter new exchange rates because all previously set
exchange rates are cleared.
Before you can make currency conversions, you must
choose a base currency and add exchange rates. The
rate of the base currency is always 1. The base currency
determines the conversion rates of the other
currencies.
1. To set the rate of exchange for the unit of currency,
scroll to the Type field, and select Options > Currency
rates.
2. A list of currencies opens, and you can see the
current base currency at the top. Scroll to the
currency type and enter the exchange rate you
would like to set per single unit of currency.
3. To change the base currency, scroll to the currency,
and select Options > Set as base curr..
4. Select Done > Yes to save the changes.
83
Data and software management
Remote configuration settings
from the following:
Application manager
When you open the application manager, you see all
the software packages that have been installed, with
their name, version number, type, and size. You can
view the details of installed applications, remove them
from your device, and specify installation settings.
In the Dev. mgr. main view, select Options and select
Select Menu > Tools > App. mgr..
•
Start configuration — Connect to the server and
receive configuration settings for your device.
New server profile — Create a new server profile.
Edit profile — Change the profile settings.
Delete — Remove the selected profile.
Enable config. — Select to receive configuration
settings from those servers for which you have a
server profile and have allowed configuration.
Disable config. — Select to stop receiving
configuration settings from all servers for which you
have a server profile.
•
•
•
•
Remote configuration
network service
•
•
Select Menu > Connect. > Dev. mgr..
You can connect to a server and receive configuration
settings for your device. You may receive server profiles
and different configuration settings from your network
operator, service providers, and company information
management department. Configuration settings may
include connection and other settings used by different
applications in your device. Available options may vary.
View log — View the configuration log of the
selected profile.
Data synchronization
Menu > Connect. > Sync.
The remote configuration connection is usually started
by the server when the device settings need to be
updated.
Use Sync to synchronize your contacts, calendar, or
notes with corresponding applications on a compatible
computer or remote Internet server. Your
synchronization settings are saved in a synchronization
profile. The application uses SyncML technology for
remote synchronization. For information on SyncML
compatibility, contact the supplier of the applications
with which you want to synchronize your device.
84
The available applications you can synchronize may
vary. Contact your service provider for more
information.
Tip: You may receive the synchronization
settings as a message from your service
provider.
Create a synchronization profile
To create a profile, select Options > New sync profile
and select from the following options:
•
•
Sync profile name — Enter a name for the profile.
Applications — Select the applications to
synchronize with the profile.
•
Connection settings — Specify the needed
connection settings. Contact your service provider
for information.
85
Tools
Select Menu > Tools.
most updated catalog content. For information on
additional items available through Nokia Catalogs,
contact your network operator or service provider.
TheTools folder contains applications used toconfigure
your device and to configure other applications.
App. mgr.—See "Application manager," p. 84.
Memory card—See "Memory card," p. 20.
Nokia Catalogs receives ongoing updates, bringing you
the latest content your network operator or service
provider offers for your device. To update the catalogs
manually, select Options > Refresh list.
Transfer—See "Transfer content between
devices," p. 26.
Profiles—See "Profiles," p. 93.
Themes—See "Themes," p. 94.
Sett. wiz.
Settings—See "Settings," p. 95.
Sett. wiz. configures your device for operator (MMS,
GPRS, and Internet), e-mail, push-to-talk (network
service), and video sharing (network service) settings
based on your network operator information.
E-mail key—See "Configure the e-mail key," p. 30.
Speed dial—See "Speed dial," p. 44.
Voice commands—See "Voice commands," p. 52.
To use these services, you may have to contact your
network operator or service provider to activate a data
connection or other services.
Nokia Catalogs
Select Menu > Catalogs. Select OK if you accept the
To edit settings, select Menu > Tools > Sett. wiz. and the
disclaimer.
item you want to configure.
Nokia Catalogs (network service) is a mobile content
shop available on your device. With Nokia Catalogs you
can discover, preview, buy, download, and upgrade
content, such as games, ringing tones, wallpapers,
services, and applications, for your device. The available
content depends on your network operator and service
provider.
If you are not able to use Sett. wiz., visit the Nokia phone
settings Web site at www.nokia.com.
Voice aid
Select Menu > Tools > Voice aid.
86
The voice aid application reads text on the screen,
allowing you to use basic functions of your device
without looking at the display.
Select from the following:
•
Contacts — Hear the entries in your contacts list. Do
not use this option if you have more than 500
contacts.
•
•
Recent calls — Hear information on your missed and
received calls, dialed numbers, and frequent calls.
Voice mailbox — Retrieve and listen to your voice
messages.
•
•
Dialler — Dial a telephone number.
Clock — Hear the current time and date.
To hear more options, select Options.
87
Media applications
To search for a file, select Options > Find. Start to enter
a search string (for example, the name or date of the
file you are searching for). Files that match the search
are shown.
Copyright protections may prevent some images, music
(including ringing tones), and other content from being
copied, modified, transferred or forwarded.
Select Menu > Media.
Media contains different media applications that allow
you to save and view images, record sounds, and play
sound clips.
Images
Select Menu > Media > Gallery > Images.
Images consists of two views:
•
In the image browser view you can send, organize,
delete, and rename images stored in your device or
memory card.
Gallery
Select Menu > Media > Gallery.
Use Gallery to access and use different types of media,
including images, videos, music, and sounds. All viewed
images and videos and all received music and sounds
are automatically saved to Gallery. You can browse,
open, and create folders; and mark, copy, and move
items to folders. Sound clips are opened in the Music
Player, and video clips and streaming links in the
RealPlayer application.
•
In the image viewer, which opens when you select
an image in the image browser view, you can view,
and send individual images. You can set images as
wallpaper for your display.
The following file formats are supported: JPEG, BMP,
PNG, and GIF 87a/89a. The device does not necessarily
support all variations of the file formats.
To open an image for viewing, select an image in the
image browser view, and select Options > Open. The
image opens in the image viewer.
To open a file or a folder, press the joystick. Images are
opened in the image viewer.
To download files into the Gallery in one of the main
folders using the browser, select Graphic downl., Video
downl., Track downl., or Sound downl.. The browser
opens, and you can choose a bookmark or enter the
address for the site to download from.
To open the next or previous image for viewing, scroll
right or left in the image viewer.
To enlarge the viewed image on the display, select
Options > Zoom in, or press 5 or 7. To reduce the viewed
image on the display, select Zoom out or press 0.
88
To view the image in full screen size, select Options >
Full screen or press 7 twice. To return to normal view,
select Options > Normal screen.
To rotate an image, select an image, and Options >
Rotate. Select Right to rotate the image clockwise by 90
degrees, or select Left to rotate the image
counterclockwise by 90 degrees.
Manage image files
Copyright protections may prevent some images,
ringing tones, and other content from being copied,
modified, transferred or forwarded.
Select Menu > Media > RealPlayer.
RealPlayer can play video clips and audio files that are
stored in the device memory or on a memory card,
transferred to your device from e-mail or compatible
PC, or streamed to your device over the Web.
Formats supported by RealPlayer include MPEG-4, MP4
(not streaming), 3GP, RV, RA, AAC, AMR, and Midi.
RealPlayer does not necessarily support all variations of
a media file format.
Tip: Streaming audio and video files means
playing them directly from the Web without
downloading them first to your device.
To view detailed information about an image, select an
image and Options > View details. Size and format of
the file, the time and date the file was last modified and
the resolution of the image in pixels are displayed.
Play video clips and stream links
To select audio and video files to play with RealPlayer,
select Options > Open, and scroll to a media clip in your
device or on a memory card.
To send an image, select the image, Options > Send, and
the method for sending.
To rename an image, select an image and Options >
To play streaming media, select a Web link that points
to a media clip, and select Play; or connect to the Web,
browse to a video clip or audio file, and select Play.
RealPlayer recognizes two kinds of links: an rtsp:// URL
and an http:// URL that points to a RAM file. Before the
content begins streaming, your device must connect to
a Web site and buffer the content. If a network
connection problem causes a playback error,
RealPlayer attempts automatically to reconnect to the
Internet access point.
To save a media clip, select Options > Save, scroll to a
folder in device memory or on a memory card, and
select Save. To save a link to a media file on the Web,
select Save link.
Rename. Enter a new name, and select OK.
To set an image as wallpaper, select the image and
Options > Set as wallpaper.
To add an image to a contact card, select an image and
Options > Assign to contact. The contacts view opens,
and you can select the contact for the image.
RealPlayer
Copyright protections may prevent some images,
ringing tones, and other content from being copied,
modified, transferred or forwarded.
89
To fast-forward or rewind the clip during playback,
scroll up or down.
•
•
Proxy serv. address — Enter the IP address of the
proxy server. This setting is only available if you
select to use a proxy server.
To increase or decrease the volume during playback,
Proxy port number — Enter the port number of the
proxy server. This setting is only available if you
select to use a proxy server.
press the volume keys.
Settings
Network settings
Select Menu > Media > RealPlayer > Options > Settings.
Video settings
Contact your service provider for the correct settings.
Select Connection > Network, scroll to the following
settings, and press the joystick to edit:
Select Loop > On, if you want to replay video clips
•
•
Default access point — Scroll to the access point to
connect to the Internet, and press the joystick.
Online time — Set the time when RealPlayer
disconnects from the network when you pause a
media clip that plays using a network link. Select
User defined, and press the joystick. Enter the time,
and select OK.
automatically after they finish playing.
Connection settings
Select Connection, scroll to the following settings, and
press the joystick to edit:
•
•
Proxy — Select whether to use a proxy server and to
key in the proxy server's IP address and port number.
Network — Change the access point to connect to
the Internet and to set the port range used when
connecting.
•
•
Lowest UDP port — Enter the lowest port number of
the server port range. The minimum value is 1024.
Highest UDP port — Enter the highest port number
of the server port range. The maximum value is
65535.
Proxy settings
Proxy servers are intermediate servers between media
servers and their users. Some service providers use
them for additional security or to speed up access to
Web pages that contain media files.
Music player
Warning: Do not hold the device near your ear
when the loudspeaker is in use, because the volume
Contact your service provider for the correct settings.
may be extremely loud.
Select Connection > Proxy, scroll to the following
Select Menu > Media > Music player.
settings, and press the joystick to edit:
90
•
Use proxy — Select Yes to use a proxy server.
With the music player, you can play music files and
create and listen to track lists. The music player
supports files with extensions such as MP3 and AAC.
Adjust music volume
To control the music volume, press the volume keys. To
mute the volume, press the lower volume key until the
volume is muted.
Listen to music
Warning: Listen to music at a moderate level.
Continuous exposure to high volume may damage your
hearing. Do not hold the device near your ear when the
loudspeaker is in use, because the volume may be
extremely loud.
Track lists
You can create a new track list and add tracks to it, or
select a saved track list.
To create a new track list, select Options > Music
library > Track lists > Options > New track list. Write the
name of the new track list, and select OK.
To select a music track, select Options > Music library.
All tracks lists all music on your device. To view sorted
songs, select Albums, Artists, Genres, or Composers. To
play a track, scroll to the track, and select Options >
Play. When a track is playing, to change between play
To add a track to a track list, open the track list, and
select Options > Add tracks.
and pause, press
and . To stop a track, press
.
Equalizer
After you add or remove music files in the device,
update your Music library. Select Options > Update
Music library. The player searches the device memory
for music files and updates them to the Music library.
Select Menu > Media > Music player > Options >
Equaliser.
You can personalize the sound of your music files with
Equaliser. You can use preset frequency settings based
on styles of music, like classical or rock. You can also
create customized settings basedonyour ownlistening
preferences.
To select the previous or next track, scroll the joystick
up or down.
To play the music tracks repeatedly, select Options >
Loop. Select All to repeat all the tracks in the current
You cannot use other functions of Music player while
folder, One to repeat the selected track, or Off to set off
Equaliser is open.
the repeating.
With Equaliser, you can enhance or diminish
frequencies during music playback and modify how
your music sounds. There are preset frequency settings
in your device, for example Rock.
To play music in random order, select a folder and
Options > Random play.
To view music track information, scroll to the desired
91
track and select Options > View details.
To use a preset frequency setting when playing music,
scroll to the frequency setting you want to use, and
select Options > Activate.
The maximum length of a voice recording is 60 seconds,
but it also depends on the storage space available in
device memory or on a memory card.
Create your own frequency setting
1. To create your own frequency setting, select
Play a voice recording
Options > New preset.
To listen to a voice recording that you just recorded,
select the play icon ( ). Select Stop to cancel playback.
2. Enter a name for the preset frequency setting, and
select OK.
The progress bar displays the playing time, position,
3. Scroll up or down to move between the frequency
bands and set the frequency on each band. To move
between bands, scroll left or right.
and length of a voice recording.
To pause playback of a voice recording, select Pause.
Playback resumes when you select Play.
4. Select Back to save the new frequency setting or
select Options > Reset to defaults to set the bands
at a neutral frequency and start over.
Voice recordings that you receive or record are
temporary files. You must save the files that you want
to keep.
Recorder
Flash player
Select Menu > Media > Recorder.
With Recorder, you can record up to 60 seconds of a
voice memo, save the voice recording as a sound clip,
and play the sound clip. Recorder supports the AMR
format.
Select Menu > Media > Flash Player.
With Flash Player, you can view, play, and interact with
flash files made for mobile devices.
To open a folder or play a flash file, scroll to the folder
or file, and press the joystick.
Press the voice key to activate Recorder. If you have
logged in to push to talk, the voice key works as a push
to talk key and does not activate Recorder.
To send a flash file to compatible devices, scroll to it,
andpressthecallkey. Copyrightprotectionmayprevent
the sending of some flash files.
To record a voice memo, select Options > Record sound
clip. Select Pause to pause the recording and Record to
resume recording. When you finish recording, select
Stop. The sound clip is automatically saved.
To switch between flash files saved on your device
memory or memory card, scroll left or right.
The available options may vary.
92
Personalization
tone that is a combination of the spoken name of
the contact and the selected ringing tone.
Ringing type — Select how you want the ringing
tone to alert.
Profiles
•
•
•
•
•
•
•
Warning: In the offline profile you cannot make
or receive any calls, including emergency calls, or use
other features that require network coverage. To make
calls, you must first activate the phone function by
changing profiles. If the device has been locked, enter
the lock code.
Ringing volume — Select the volume level of the
ringing tone.
Message alert tone — Select a tone for received text
messages.
E-mail alert tone — Select a tone for received e-mail
messages.
Select Menu > Tools > Profiles.
IM alert tone — Select a tone for received instant
messages.
You can adjust and customize the ringing tones, alert
tones, and other device tones for different events,
environments, or caller groups.
Vibrating alert — Select whether you want the
device to vibrate when you receive a call.
Keypad tones — Set the volume level of the device
keypad tones.
To customize a profile, scroll to the desired profile in
the list, and select Options > Personalise.
•
•
Warning tones — Set the warning tones on or off.
Alert for — You can set the device to ring only upon
calls from phone numbers that belong to a selected
contact group. Phone calls coming from outside that
group have a silent alert.
Define the following settings:
•
Ringing tone — Select a ringing tone from the list,
or select Tone downloads to open a bookmark folder
containing a list of bookmarks for downloading
tones using the browser. To listen to the selected
tone, select Play. If you have two alternate phone
lines in use, you can specify a ringing tone for each
line.
•
Profile name — You can give a name to a new profile
or rename an existing profile. The General and
Offline profiles cannot be renamed.
The Offline profile prevents your device from
accidentally switching on, sending or receiving
messages, or using Bluetooth; it also closes any
Internet connection that may be in operation when
the profile is selected. The Offline profile does not
prevent you from establishing a wireless LAN
•
•
Video call tone — Select a ringing tone for video
calls.
Say caller's name — Activate the text-to-speech
ringing tone feature. When someone from your
contacts list calls you, the device sounds a ringing
93
connection at a later time, so comply with any
applicable safety requirements when establishing
and using wireless LAN connections.
To preview a theme, highlight the theme you want to
preview, and select Options > Preview. Select Apply to
start using the new theme.
To change a profile, scroll to the desired profile in the
list, and select Options > Activate. If you select the
Offline profile, you cannot send or receive messages or
use WLAN to read your e-mails.
To create a new profile, select Options > Create new,
and define the settings.
Themes
Select Menu > Tools > Themes.
You can change the look of the display of your device.
To change the look of the display, highlight the theme
you want to use, and select Options > Apply.
To edit a theme, highlight the theme you want to edit,
and select Options > Edit. Select Wallpaper to change
the background image in the standby modes, or Power
saver to use a text or the date and time as a power saver
that appears on the display when no key presses have
been made for a some time.
To download themes, you need to establish a network
connection that allows you to download themes from
Internet sources that are compatible with your device.
To download a theme, select Theme downloads. Enter
the link from which you want to download your theme.
Once the theme is downloaded you can preview,
activate, or edit it.
94
Settings
Select Menu > Tools > Settings.
application in your device. When you change the
language, the device restarts.
You can define and modify various settings of your
device. Modifying these settings affects the operation
of your device across several applications.
•
•
Writing language — Select a language from the list.
Changing the writing language also affects the
characters that are available when writing text.
Welcome note / logo — Select Default to use the
default image, Text to enter a welcome note of your
own, or Image to select an image from the Gallery.
The welcome note or image is displayed briefly each
time you switch on the device.
Some settings may be preset for the device or sent to
you in a configuration message by your network
operator or service provider. You may not be able to
change such settings.
Scroll to the setting that you want to edit, and press the
•
Orig. phone settings — Restore the original device
settings. To do this, you need your device lock code.
After resetting, the device may take a longer time to
power on. Documents, contact information,
calendar entries, and files are unaffected.
joystick to do the following:
•
•
•
•
Switch between two values, such as on or off.
Select a value from a list.
Open a text editor to enter a value.
Open a slider to decrease or increase the value by
scrolling left or right.
Standby mode settings
Select Standby mode and from the following:
Phone settings
•
Active standby — Select On to have shortcuts to
different applications available in the active standby
mode.
Select Phone to change the language settings, standby
mode settings, and display settings of your device.
•
Left selection key, Right selection key — Change the
shortcuts that open from the left and right selection
keys in the standby screen. Press joystick, select a
function from the list, and OK.
General settings
Select General and from the following:
•
Navigation key right, Navigation key left, Navigat.
key down, Navigation key up, Selection
key — Change the shortcuts that open when you
•
Phone language — Select a language from the list.
Changing the device language affects every
95
scroll to different directions. These settings are not
available if you select Active standby > On.
Standby apps — Select the applications that you
want to access from the active standby.
•
•
Internet call waiting — Activate this feature to be
notified of a new incoming call while you have a net
call in progress.
•
•
Internet callalert — Set this onif youwantthedevice
to respond to the caller that it is busy. If you set this
off, the device emits a busy tone to the caller and you
receive a notification about the missed call.
Default call type — Select Cellular to make normal
calls to the phone number or Internet to use VoIP to
call the number or address.
Active standby mailbox — Select the inbox or the
mailbox that is shown in the active standby.
•
•
Display settings
Select Display and from the following:
Reject call with SMS — Select Yes to send a text
message automatically to the person who is calling
you informing why you cannot answer their
incoming call.
•
Light sensor — Adjust the amount of light required
to illuminate the device display.
•
Power saver time-out — Select the amount of time
before the screen saver is activated. Activating the
screen saver lengthens the device operating time.
Light time-out — Set how quickly after last keypress
the display dims.
•
•
Message text — Enter the text that is sent when you
cannot answer an incoming call and want to
automatically send a text message as a reply.
Image in video call — Select Use selected to select a
still image to be displayed instead of a video during
a video call or None to not send any image during a
video call.
•
Call settings
•
Automatic redial — Select On to redial a number if it
was busy at the first call attempt. Your device makes
a maximum of 10 attempts to connect the call.
Summary after call — Select On to briefly display the
approximate duration of the last call.
Select Call and from the following:
•
Send my caller ID — Select Yes to display your phone
number to the person you are calling or Set by
network to let the network to determine whether
your caller ID is sent.
•
•
Speed dialling — Select On to activate speed dialing
on your device. To dial a phone number assigned to
the speed dialing keys (2-9), press and hold the key.
•
•
Send my net call ID — Set this feature on if you want
to display your net caller ID to the person you are
calling.
See "Speed dial," p. 44.
Call waiting — Select Activate to be notified of a new
incoming call while you have a call in progress or
Check status to check if the function is active on the
network.
•
•
Anykey answer — Select On to answer an incoming
call by briefly pressing any key, except the end key.
Line in use — Select Line 1 or Line 2 to change the
phone line for outgoing calls and text messages
96
(network service). This setting is displayed only if the
SIM card supports the alternate line service and a
subscription to two phone lines.
•
•
Wireless LAN — Determine if the device displays an
indicator when a wireless LAN is available, and how
often the device searches for networks.
Configurations — View and delete trusted servers
from which your device may receive configuration
settings.
•
•
Line change — Select Disable to prevent line
selection (network service). To change this setting,
you need the PIN2 code.
Internet call alert — Select Off to notify incoming net
calls that your device is busy or On to accept
incoming net calls.
To obtain information about wireless LAN or
subscribing to a packet data service and the
appropriate connection and configuration settings,
contact your network operator or service provider.
The settings available for editing may vary.
Connection settings
Select Menu > Tools > Settings > Connection and from
Access points
the following:
Select Menu > Tools > Settings > Connection > Access
•
Access points — Set up new or edit existing access
points. Some or all access points may be preset for
your device by your service provider, and you may
not be able to create, edit, or remove them.
Access point groups — Set up new or edit existing
access point groups that are used in automatic
connection establishment and e-mail roaming.
Packet data — Determine when packet data
connections are used, and enter the access point if
you use your device as a modem for a computer.
Internet tel. settings — Define settings for net calls.
SIP settings — View or create session initiation
protocol (SIP) profiles.
points.
An access point is where your device connects to the
network by way of a data connection. To use e-mail and
multimedia services or to browse web pages, you must
first define access points for these services.
•
•
An access point group is used for grouping and
prioritizing access points. An application can use a
group as a connection method instead of a single access
point. In that case, the best available access point inside
a group is used for making the connection, and in case
of e-mail, also for roaming.
•
•
Some or all access points may be preset for your device
by your service provider, and you may not be able to
create, edit, or remove them.
•
•
Data call — Set the time-out period after which data
call connections automatically end.
VPN — Install and manage VPN policies, manage VPN
policy servers, see the VPN log, and create and
manage VPN access points.
See "Internet access points," p. 60.
97
connection only when an application or action
requires it.
Access point groups
Select Menu > Tools > Settings > Connection > Access
•
as a packet data modem to your computer.
point groups.
An access point group is used for grouping and
prioritizing access points. An application can use a
group asa connection method instead of a singleaccess
point. In that case the best available access point inside
a group is used for making connection and in case of e-
mail, also for roaming. See "Access point
These settings affect all access points for packet data
connections.
groups," p. 70.
Select Menu > Tools > Settings > Connection > Internet
tel. settings. Select Options > New profile or Options >
Edit.
Packet data
Scroll to Name, press the joystick, enter a name for the
Select Menu > Tools > Settings > Connection > Packet
profile, and select OK.
data.
Scroll to SIP profiles, press the joystick, select a profile
and OK. SIP protocols are used for creating, modifying,
and terminating communications sessions such as net
calls with one or more participants. SIP profiles include
settings for these sessions.
Your device supports packet data connections, such as
GPRS in the GSM network. When you are using your
device in GSM and UMTS networks, it is possible to have
multiple data connections active at the same time;
access points can share a data connection, and data
connections remain active (for example, during voice
calls). See "Connection manager," p. 68.
To save your settings, press Back.
Data call settings
Packet data settings
Select Menu > Tools > Settings > Connection > Data
The packet data settings affect all access points using a
call.
packet data connection.
To set the time-out period after which data calls
automatically end if no data has been transferred,
select Online time, and press the joystick. Select User
defined to enter the time yourself or Unlimited to keep
the connection active until you select Options >
Disconnect.
Select from the following:
•
Packet data conn. — Select When available to
register the device to the packet data network when
you switch the device on in a supported network.
Select When needed to establish a packet data
98
VPN
Wireless LAN
LAN.
To have an indicator displayed when there is a wireless
LAN available in your current location, select Show
availability > Yes.
To select the time interval for your device to scan for
available wireless LANs and update the indicator, select
Scan for networks.
Select Menu > Tools > Settings > Connection > Wireless
VPN access points
To manage VPN access points, select VPN > VPN access
points > Options, and from the following:
•
Edit — Edit the selected access point. If the access
point is in use or its settings are protected, you
cannot edit it.
•
•
New access point — Create a new VPN access point.
Delete — Delete the selected access point.
Advanced WLAN settings
VPN access point settings
Contact your service provider for the correct access
Select Menu > Tools > Settings > Connection > Wireless
LAN > Options > Advanced settings. The wireless LAN
advanced settings are normally defined automatically,
and changing them is not recommended.
point settings.
To edit VPN access point settings, select the access point
and Options.
To edit the settings manually, select Automatic
Select from the following:
config. > Disabled, and define the following:
•
Connection name — Enter a name for the VPN
connection. The maximum length of the name is 30
characters.
•
Long retry limit — Enter the maximum number of
transmission attempts if the device does not receive
a receiving acknowledgement signal from the
network.
•
•
•
•
VPN policy — Select a VPN policy to be used with this
access point.
•
•
Short retry limit — Enter the maximum number of
transmission attempts if the device does not receive
a clear-to-send signal from the network.
RTS threshold — Select the data packet size at which
the wireless LAN access point device issues a request
to send before sending the packet.
Internet access pt. — Select the Internet access point
to be used with this VPN access point.
Proxy serv. address — Enter the proxy server address
of this VPN access point.
Proxy port number — Enter the number of the proxy
port.
•
•
TX power level — Select the power level of your
device when sending data.
Radio measurements — Enable or disable the radio
measurements.
99
•
Power saving — Select whether to save the power
in the device battery.
802.1x authenticates and authorizes devices to access
a wireless network, and prevents access if the
authorization process fails.
To restore all settings to their original values, select
Select WLAN security sett.. and from the following:
Options > Restore defaults.
•
•
•
WPA mode — Select EAP (Extensible Authentication
Protocol) or Pre-shared key (a secret key used for
device identification).
Security settings for wireless LAN access
points
EAP plug-in settings — If you selected WPA mode >
EAP, select which EAP plug-ins defined in your device
to use with the access point.
Select Menu > Tools > Settings > Connection > Access
points. Select Options > New access point and start to
create a wireless LAN access point, or select a wireless
LAN access point and Options > Edit.
Pre-shared key — If you selected WPA mode > Pre-
shared key, enter the shared private key that
identifies your device to the wireless LAN to which
you connect.
WEP security settings
In the access point settings, select WLAN security
The settings available for editing may vary.
WPA security settings
mode > WEP.
Wired equivalent privacy (WEP) encryption method
encrypts data before it is transmitted. Access to the
network is denied to users who do not have the
required WEP keys. When WEP security mode is in use,
if your device receives a data packet not encrypted with
the WEP keys, the data is discarded.
In the access point settings, select WLAN security
mode > WPA/WPA2.
Select WLAN security sett.. and from the following:
•
•
•
WPA mode — Select EAP (Extensible Authentication
Protocol) or Pre-shared key (a secret key used for
device identification).
In an Ad-hoc network, all devices must use the same
WEP key.
EAP plug-in settings — If you select WPA mode >
EAP, select which EAP plug-ins defined in your device
to use with the access point.
Select WLAN security sett. and from the following:
•
•
•
WEP key in use — Select the desired WEP key.
Authentication type — Select Open or Shared.
WEP key settings — Edit the settings for the WEP key.
Pre-shared key — If you select WPA mode > Pre-
shared key, enter the shared private key that
identifies your device to the wireless LAN to which
you connect.
802.1x security settings
In the access point settings, select WLAN security
The settings available for editing may vary.
mode > 802.1x.
100
EAP
Configurations
To view the EAP (extensible authentication protocol)
plug-ins currently installed in your device (network
service), select Menu > Tools > Settings > Connection >
Access points. Select Options > New access point and
define an access point that uses wireless LAN as a data
bearer and 802.1x or WPA/WPA2 as the security mode.
Select WLAN security sett. > WPA mode > EAP, scroll to
EAP plug-in settings, and press the joystick.
To view and delete configurations for trusted servers,
select Menu > Tools > Settings > Connection >
Configurations.
You can receive messages from your network operator,
service provider, or companyinformationmanagement
that contain configuration settings for trusted servers.
These settings are automatically saved in
Configurations. You may receive configuration settings
for access points, multimedia or e-mail services, and IM
or synchronization settings from trusted servers.
The extensible authentication protocol (EAP) plug-ins
are used in wireless networks to authenticate wireless
devices and authentication servers, and the different
EAP plug-ins make possible the use of various EAP
methods (network service).
To delete configurations for a trusted server, scroll to
the server, and press the backspace key. The
configuration settings for other applications provided
by this server are also deleted.
To use an EAP plug-in when you connect to a WLAN
using the access point, select the desired plug-in and
Options > Enable. The EAP plug-ins enabled for use with
this access point have a check mark next to them. To
not use a plug-in, select Options > Disable.
Date and time settings
See "Clock," p. 59.
To edit the EAP plug-in settings, select Options >
Configure.
Security settings
To change the priority of the EAP plug-in settings, select
Options > Raise priority to attempt to use the plug-in
before other plug-ins when connecting to the network
with the access point, or Options > Lower priority to use
this plug-in for network authentication after
See "Define security settings," p. 103.
Enhancement settings
attempting to use other plug-ins.
Select Menu > Tools > Settings > Enhancement.
The available options may vary.
See the device help for more information on EAP
Warning: When you use the headset, your ability
to hear outside sounds may be affected. Do not use the
headset where it can endanger your safety.
plugins.
101
With most enhancements, you can select from the
following settings:
•
Default profile — Select the profile that is activated
when you attach an enhancement to your device.
Automatic answer — Let the device answer phone
calls automatically when an enhancement is
attached. Select On to have the device answer an
incoming call automatically after 5 seconds. If the
ringing type is set to Beep once or Silent in the
Profiles menu, automatic answer is disabled.
Lights — Select On to illuminate the device while it
is attached to an enhancement.
•
•
102
Security
•
•
•
PIN code — Change the PIN code. The PIN code must
be 4 to 8 numbers long. The PIN code protects your
SIM card against unauthorized use and is provided
with the SIM card. After three consecutive incorrect
PIN code entries, the PIN code is blocked, and you
need to use the PUK code to unblock it before you
can use the SIM card again.
Device security
Select Menu > Tools > Settings > Security > Phone and
SIM.
You can modify the security settings for the PIN code,
automatic lock, and SIM card change, and change codes
and passwords.
PIN2 code — Change the PIN2 code. The PIN2 code
must be 4 to 8 numbers long. The PIN2 code is
required to access some functions of the device and
isprovided withthe SIM card. After three consecutive
incorrect PIN2 code entries, the PIN2 code is blocked,
and you need to use the PUK2 code to unblock it
before you can use the SIM card again.
Avoid using codes that are similar to emergency
numbers to prevent accidental dialing of the
emergency number.
Codes are shown as asterisks. When you change a code,
enter the current code, then the new code twice.
Autolock period — Set a time-out after which the
device is automatically locked and can be used only
if the correct lock code is entered. Enter a number for
the time-out in minutes, or select None to turn off
the autolock period. When the device is locked, you
can still answer incoming calls and calls may still be
possible to the official emergency number
Define security settings
To define device and SIM card settings, select a setting
and Options > Change.
When calls are limited to closed user groups, calls may
be possible to the official emergency number
programmed into your device.
programmed into your device.
•
Lock code — Change the lock code. The new code can
be 4-255 characters long. Both alphabets and digits
can be used, and both uppercase and lowercase
alphabets are possible. The device notifies you if the
lock code is not properly formatted. The preset code
is 12345. To avoid unauthorized use of your device,
change the lock code. Keep the new code secret and
in a safe place separate from your device.
Define the following settings:
•
PIN code request — Select On to request that the PIN
code is entered each time the device is switched on.
This setting cannot be changed if the device is
switched off. Some SIM cards do not allow turning
off the PIN code request.
103
•
•
Lock if SIM changed — Set the device to ask for the
lock code when an unknown, new SIM card is
With the fixed dialing service, you can restrict calls from
your device to only certain phone numbers. Not all SIM
inserted into your device. The device maintains a list cards support the fixed dialing service. Contact your
of SIM cardsthat arerecognized as the owner’scards. service provider for more information.
Allow remote lock — If you set this option on, you
can lock the device by sending a predefined text
message from another phone. When you set this
option on, you need to enter the remote lock
message and confirm the message. The message
must be at least 5 characters long.
Select Options, and select from the following options:
•
Activ. fixed dialling — Restrict calls from your device.
To cancel the service, select Deact. fixed dialling. You
need your PIN2 code to activate and deactivate fixed
dialing or edit your fixed dialing contacts. Contact
your service provider if you do not have the code.
New SIM contact — Add a phone number to the list
of numbers to which calls are allowed. Enter the
contact name and phone number. To restrict calls by
a country prefix, enter the country prefix in New SIM
contact. All phone numbers to which calls are
allowed must start with this country prefix.
Add from Contacts — Copy a contact from Contacts
to your fixed dialing list.
•
•
Closed user group (network service) — Specify a
group of people to whom you can call and who can
call you.
•
Confirm SIM services (network service) — Set the
device to display confirmation messages when you
are using a SIM card service.
•
Change the barring password
Tip: To send text messages to the SIM contacts
while the fixed dialing service is active, you
need to add the text message center number
to the fixed dialing list.
To change the password used for barring voice, fax, and
data calls, select Menu > Tools > Settings > Call
barring > Cellular call barring > Options > Edit barrings
passw.. Enterthecurrentcode, then the newcodetwice.
The barring password must be four digits long. For
details, contact your service provider.
Toview or edit a phone numberto which callsfrom your
device are allowed, select Options > SIM contacts >
Fixed dialling contacts.
To call the contact, press the call key.
To edit the phone number, select Options > Edit. You
may need your PIN2 code to edit your fixed dialing
numbers.
To delete the contact, press the backspace key.
Fixed dialing
When fixed dialing is activated, calls may be possible to
the official emergency number programmed into your
device.
Select Menu > Contacts > Options > SIM contacts > Fixed
dialling contacts.
104
online bank or a remote server to transfer confidential
information. They should also be used if you want to
reduce the risk of viruses or other malicious software,
and to check the authenticity of software when you
download and install software to your device.
Certificate manager
Important: Note that even if the use of
certificates makes the risks involved in remote
connections and software installation considerably
smaller, they must be used correctly in order to benefit
from increased security. The existence of a certificate
does not offer any protection by itself; the certificate
manager must contain correct, authentic, or trusted
certificates for increased security to be available.
Certificates have a restricted lifetime. If Expired
certificate or Certificate not valid yet is shown even if
the certificate should be valid, check that the current
date and time in your device are correct.
Tip: When you add a new certificate, check its
authenticity.
VPN
See "Mobile VPN ," p. 70.
Security settings for
Before changing any certificate settings, you must
make sure that you really trust the owner of the
certificate and that the certificate really belongs to the
listed owner.
wireless LAN access points
See "Security settings for wireless LAN access
points," p. 100.
Digital certificates are used to verify the origins of
software but do not guarantee safety. There are three
different types of certificates: authority certificates,
personal certificates, and server certificates. During a
secure connection, a server may send a server
certificate to your device. Upon receipt, it is checked
through an authority certificate stored on your device.
You receive notification if the identity of the server is
not authentic or if you do not have the correct
certificate in your device.
Download a certificate from a web site, or receive a
certificate as an e-mail attachment, or as a message
sent through a Bluetooth or infrared connection.
Certificates should be used when you connect to an
105
Shortcuts
In applications
Here are some of the available keyboard shortcuts in
your device. Shortcuts can make the use of the
applications more efficient.
Select text. Press and Shift + joystick
hold the shift key and
scroll left or right with
the joystick to select
text.
Some shortcuts are application-specific and they are
not available for all applications.
Active standby mode
Copy.
Cut.
Paste.
Italics.
Bold.
Ctrl+C
Ctrl+X
Ctrl+V
Ctrl+I
Ctrl+B
Left selection key +
Lock and unlock the keypad.
blue function key
Call key
0
Open the Log.
Press and hold to open
Services and connect to the
Web.
1
Press and hold to call your
Enter a number or a Press blue function key once
voice mailbox.
character marked in
blue on a key.
(so that you see ) + the
other key.
Number key (2–9)
Call a phone number using
speed dialling. You must first
activate speed dialling
Enter only numbers or Press blue function key twice
characters marked in
blue on a key.
(so that you see
other key.
) + the
(Menu > Tools > Settings >
Call > Speed dialling > On).
Switch between
character cases.
Press the shift key.
Blue function key +
Chr
Activate infrared.
Blue function key +
Activate and deactivate
Bluetooth.
Image viewer
Send the image.
Zoom out.
Ctrl
Call key
0
106
Zoom in.
5
7
Zoom in. Press twice
for the full screen size.
Scroll left in the
zoomed image.
4
6
2
8
Scroll right in the
zoomed image.
Scroll up in the
zoomed image.
Scroll down in the
zoomed image.
Rotate clockwise.
3
1
Rotate
counterclockwise.
Switch between the
full screen size and
normal view.
*
107
Battery information
Your device is powered by a rechargeable battery. The
the capacity and lifetime of the battery. Always try to
full performance of a new battery is achieved only after keep the battery between 15°C and 25°C (59°F and 77°
two or three complete charge and discharge cycles. The F). A device with a hot or cold battery may not work
battery can be charged and discharged hundreds of
temporarily, even when the battery is fully charged.
times, but it will eventually wear out. When the talk and Battery performance is particularly limited in
standby times are noticeably shorter than normal, buy temperatures well below freezing.
a new battery. Use only Nokia approved batteries, and
recharge your battery only with Nokia approved
chargers designated for this device.
Do not dispose of batteries in a fire as they may explode.
Batteries may also explode if damaged. Dispose of
batteries according to local regulations. Please recycle
when possible. Do not dispose as household waste.
Unplug the charger from the electrical plug and the
device when not in use. Do not leave fully charged
battery connected to a charger, since overcharging may
shorten its lifetime. If left unused, a fully charged
battery will lose its charge over time.
1500 mAh Li-Ion battery
(BP-5L) information
If the battery is completely discharged, it may take a
few minutes before the charging indicator appears on
the display or before any calls can be made.
Variation in talk time and standby time may occur,
depending onthe SIM card, network andusage settings,
and the style and environment of use.
Use the battery only for its intended purpose. Never use
•
•
•
•
GSM talk time: up to 6 hours
any charger or battery that is damaged.
WCDMA talk time: up to 5 hours
GSM standby time: up to 7.6 days
WCDMA standby time: up to 8.7 days
Do not short-circuit the battery. Accidental short-
circuiting can occur when a metallic object such as a
coin, clip, or pen causes direct connection of the positive
(+) and negative (-) terminals of the battery. (These look
like metal strips on the battery.) This might happen, for
example, when you carry a spare battery in your pocket
or purse. Short-circuiting the terminals may damage
the battery or the connecting object.
Nokia battery
authentication guidelines
Leaving the battery in hot or cold places, such as in a
Always use original Nokia batteries for your safety. To
108
closed car in summer or winter conditions, will reduce
check that you are getting an original Nokia battery,
and
purchase it from an authorized Nokia dealer,
What if your battery is not
authentic?
inspect the hologram label using the following steps:
Successful completion of the steps i not a total
s
If you cannot confirm that your Nokia battery with the
hologram on the label is an authentic Nokia battery,
assurance of the authenticity of the battery. If you have
any reason to believe that your battery is not an
authentic original Nokia battery, you should refrain
The use of a battery that
please do not use the battery.
is not approved by the manufacturer may be dangerou
and may result in poor performance and damage to
s
from using it
. If authenticity cannot be verified, return
the battery to the place of purchase.
your
enhancements. It may also
device and its
invalidate any approval or
warranty applying to th
e
Authenticate hologram
device.
1. When looking at the hologram
To find out more about original Nokia batteries, visi
t
on the label, you should see
the Nokia connecting hands
symbol from oneangle andthe
Nokia Original Enhancements
logo when looking from
another angle.
www.nokia-asia.com/battery
check
.
2. When you angle the hologram
left, right, down, and up, you
should see 1, 2, 3, and 4 dots
on each side respectively.
109
110
Care and maintenance
Your device is a product of superior design and
craftsmanship and should be treated with care. The
suggestions below will help you protect your warranty
coverage.
•
•
•
Do not paint the device. Paint can clog the moving
parts and prevent proper operation.
Use a soft, clean, dry cloth to clean any lenses, such
as camera, proximity sensor, and light sensor lenses.
•
Keep the device dry. Precipitation, humidity, and all
types of liquids or moisture can contain minerals
that will corrode electronic circuits. If your device
does get wet, remove the battery, and allow the
device to dry completely before replacing it.
Use only the supplied or an approved replacement
antenna. Unauthorized antennas, modifications, or
attachments could damage the device and may
violate regulations governing radio devices.
•
•
Use chargers indoors.
•
•
Do not use or store the device in dusty, dirty areas.
Its moving parts and electronic components can be
damaged.
Always create a backup of data you want to keep,
such as contacts and calendar notes, before sending
your device to a service facility.
Do not store the device in hot areas. High
temperatures can shorten the life of electronic
devices, damage batteries, and warp or melt certain
plastics.
All of the above suggestions apply equally to your
device, battery, charger, or any enhancement. If any
device is not working properly, take it to the nearest
authorized service facility for service.
•
Do not store the device in cold areas. When the
device returns to its normal temperature, moisture
can form inside the device and damage electronic
circuit boards.
•
•
Do not attempt to open the device other than as
instructed in this guide.
Do not drop, knock, or shake the device. Rough
handling can break internal circuit boards and fine
mechanics.
•
Do not use harsh chemicals, cleaning solvents, or
strong detergents to clean the device.
111
Additional safety information
devices. Consult a physician or the manufacturer of the
Operating environment
medical device to determine if they are adequately
shielded from external RF energy or if you have any
questions. Switch off your device in health care facilities
when any regulations postedinthese areasinstruct you
to do so. Hospitals or health care facilities may be using
equipment that could be sensitive to external RF
energy.
Remember to follow any special regulations in force in
any area, and always switch off your device when its
use is prohibited or when it may cause interference or
danger. Use the device only in its normal operating
positions. This device meets RF exposure guidelines
when used either in the normal use position against the
ear or when positioned at least 2.2 centimeters (7/8
inches) away from the body. When a carry case, belt clip
or holder is used for body-worn operation, it should not
contain metal and should position the device the
above-stated distance from your body.
Pacemakers
Pacemaker manufacturers recommend that a
minimum separation of 15.3 centimeters (6 inches) be
maintained between a wireless phone and a
pacemaker to avoid potential interference with the
pacemaker. These recommendations are consistent
with the independent research by and
To transmit data files or messages, this device requires
a quality connection to the network. In some cases,
transmission of data files or messages may be delayed
until such a connection is available. Ensure that the
above separation distance instructions are followed
until the transmission is completed.
recommendations of Wireless Technology Research.
Persons with pacemakers should do the following:
•
Always keep the device more than 15.3 centimeters
(6 inches) from the pacemaker
Parts of the device are magnetic. Metallic materials may
be attracted to the device. Do not place credit cards or
other magnetic storage media near the device, because
information stored on them may be erased.
•
•
Not carry the device in a breast pocket
Hold the device to the ear opposite the pacemaker
to minimize the potential for interference.
•
If you suspect interference, switch off your device,
and move the device away.
Medical devices
Operation of any radio transmitting equipment,
including wireless phones, may interfere with the
functionality of inadequately protected medical
112
dangerous to the operation of the aircraft, disrupt the
wireless telephone network, and may be illegal.
Hearing aids
Some digital wireless devices may interfere with some
hearing aids. If interference occurs, consult your service
provider.
Potentially explosive
environments
Vehicles
Switch off your device when in any area with a
potentially explosive atmosphere, and obey all signs
and instructions. Potentially explosive atmospheres
include areas where you would normally be advised to
turn off your vehicle engine. Sparks in such areas could
cause an explosion or fire resulting in bodily injury or
even death. Switch off the device at refueling points
such as near gas pumps at service stations. Observe
restrictions on the use of radio equipment in fuel
depots, storage, and distribution areas; chemical
plants; or where blasting operations are in progress.
Areas with a potentially explosive atmosphere are
often, but not always, clearly marked. They include
below deck on boats, chemical transfer or storage
facilities, vehicles using liquefied petroleum gas (such
as propane or butane), and areas where the air contains
chemicals or particles such as grain, dust, or metal
powders.
RF signals may affect improperly installed or
inadequately shielded electronic systems in motor
vehicles such as electronic fuel injection systems,
electronic antiskid (antilock) braking systems,
electronic speed control systems, and air bag systems.
For more information, check with the manufacturer, or
its representative, of your vehicle or any equipment
that has been added.
Only qualified personnel should service the device, or
install the device in a vehicle. Faulty installation or
service may be dangerous and may invalidate any
warranty that may apply to the device. Check regularly
that all wireless device equipment in your vehicle is
mounted and operating properly. Do not store or carry
flammable liquids, gases, or explosive materials in the
same compartment as the device, its parts, or
enhancements. For vehicles equipped with an air bag,
remember that air bags inflate with great force. Do not
place objects, including installed or portable wireless
equipment in the area over the air bag or in the air bag
deployment area. If in-vehicle wireless equipment is
improperly installed, and the air bag inflates, serious
injury could result.
Emergency calls
Important: Wireless phones, including this
device, operate using radio signals, wireless networks,
landline networks, and user-programmed functions.
Because of this, connections in all conditions cannot be
guaranteed. You should never rely solely on any
Using your device while flying in aircraft is prohibited.
Switch off your device before boarding an aircraft. The
use of wireless teledevices in an aircraft may be
113
wireless device for essential communications like
medical emergencies.
CERTIFICATION
To make an emergency call:
INFORMATION (SAR)
1. If the device is not on, switch it on. Check for
adequate signal strength.
THIS MOBILE DEVICE MEETS
GUIDELINES FOR EXPOSURE TO
RADIO WAVES.
Some networks may require that a valid SIM card is
properly inserted in the device.
2. Press the end key as many times as needed to clear
the display and ready the device for calls.
Your mobile device is a radio transmitter and receiver.
It is designed not to exceed the limits for exposure to
radio waves recommended by international guidelines.
These guidelines were developed by the independent
scientific organization ICNIRP and include safety
margins designed to assure the protection of all
persons, regardless of age and health.
3. Enter the official emergency number for your
present location. Emergency numbers vary by
location.
4. Press the call key.
If certain features are in use, you may first need to turn
those features off before you can make an emergency
call. Consult this guide or your service provider for more
information.
The exposure guidelines for mobile devices employ a
unit of measurement known as the Specific Absorption
Rate or SAR. The SAR limit stated in the ICNIRP
guidelines is 2.0 watts/kilogram (W/kg) averaged over
10 grams of tissue. Tests for SAR are conducted using
standard operating positions with the device
When making an emergency call, give all the necessary
information as accurately as possible. Your wireless
device may be the only means of communication at the
scene of an accident. Do not end the call until given
permission to do so.
transmitting at its highest certified power level in all
tested frequency bands. The actual SAR level of an
operating device can be below the maximum value
because the device is designed to use only the power
required to reach the network. That amount changes
depending on a number of factors such as how close
youare toanetwork basestation. ThehighestSARvalue
under the ICNIRP guidelines for use of the device at the
ear is 0.79 W/kg.
Use of device accessories and enhancements may result
in different SAR values. SAR values may vary depending
114
on national reporting and testing requirements and the
network band. Additional SAR information may be
provided under product information at
www.nokia.com.
115
Index
contacts
A
C
access points 60, 97
ad hoc network 68
answering calls 45
application manager 84
applications
cable 62
groups 54
calculator 82
calendar 57
calling 44
ringing tones 55
calls
copying text 24
common actions 25
attachments 31
barring 45
diverting 45
D
audio files 89
settings 96
data
authority certificates 105
automatic answer 101
cells 78
connections 67
declining calls 45
display
certificates 105
charging the battery 12
chart sheets 78
chat 40
B
indicators 18
settings 96
diverting calls 45
documents 75
barring calls 45
barring password 104
battery
clock 59
connecting to the Internet 60
connection manager 68
connection methods
Bluetooth 63
cable 62
charge level 18
charging 12
E
installing 10
e-mail
battery charger 16
blogs 73
accounts 33
infrared 66
messages 29
modem 69
Bluetooth
replying 31
WLAN 68
connections 63
pairing 64
writing 32
connections
email data roaming 70
ending network connections 69
enhancement settings 101
equalizer 91
GPRS settings 60
WLAN settings 61, 99
connectors 13
contact groups 54
contact information 55
settings 63
bookmarks 72
browsing Web pages 71, 74
business cards 55
116
F
J
See VPN
feeds 73
joystick 95
modem 69
file manager 75
multimedia messages
creating 37
K
flash player 92
keyguard 15
keys 13
sending 37
G
gallery 88
general packet radio service
See GPRS
settings 39
L
music player 90
GPRS
language 95
listening to music 90
locking
access point settings 60
general 67
N
notes 82
settings 98
device 16
keypad 15
logs 46
O
H
outline view 76
help 21
M
P
I
mail
packet data
IM 40
See e-mail
access point settings 60
general 67
images
media applications 88
memory 19
add to contacts 89
set as wallpaper 89
zooming in or out 88
indicators 18
infrared 66
settings 98
monitoring 19
memory card 20
passwords 20
menu 23
pairing 64
passwords
memory card 20
pasting text 24
personal certificates 105
personalization 93, 94
phone
installing
messages
battery 10
deleting 32
SIM card 10
e-mail 29
instant messaging 40
Internet 71
folders 28
calls 44
multimedia messages 37
picture messages 36
special messages 43
text messages 35
language 95
access points 60
net call settings 97
settings 60
settings 95
video calls 46
picture messages 36
117
playing
connection 97
display 96
selecting 23
writing 24
music 90
video and audio 89
voice recordings 92
Pop-Port connector 16
presentations 78
printing 81
general 95
text messages
Internet 60
card 35
replying 35
profiles 93
security 103
sending 35
writing 35
R
standby 95
themes 94
text messages 36
Web 73
to-do list 57
RealPlayer
tools folder 86
track lists 91
tutorial 21
playing media clips 89
settings 90
WLAN 99
SettingWizard 86
shortcuts 18, 106
signal strength 18
SIM access profile 65
SIM card
recording
calls 92
U
voice 92
rejecting calls 45
remote configuration
settings 84
USB data cable 62
installing 10
V
text messages 35
slide shows 79
SMS messages 35
special messages 43
speed dialing 44
standby
remote synchronization 84
ringing tones 55
video calls 46
video clips 89
virtual private network 70
voice commands 52
voice dialing 52
voice mailbox 44
voice memos 92
voice recorder 92
volume 17, 91
S
screen export 80
security
mode 17
device 103
settings 95
memory card 20
selecting text and objects 23
selection key settings 95
service commands 43
settings
storage 20
switch on and off 12
VPN 70
T
W
text
Bluetooth 63
Web 71
copying 24
pasting 24
calendar 58
settings 73
118
calls 96
welcome note 95
WLAN
access point settings 61
general 68
security settings 100
settings 99
worksheets 77
write text 24
writing language 95
119
MANUFACTURER’S LIMITED WARRANTY
NOTE! This Limited Warranty is in addition to, and does not affect your
legal (statutory) rights under your applicable national laws relating to
the sale of consumer products.
c) ninety (90) days for the media on which any software is provided,
e.g. CD-rom, memory card.
As far as your national laws permit, the Warranty Period will not be
extended or renewed or otherwise affected due to subsequent resale,
repair or replacement of the Product. However, repaired part(s) will be
warranted for the remainder of the original Warranty Period or for sixty
(60) days from the date of repair, whichever is longer.
Nokia Corporation (“Nokia”) provides this Limited Warranty to person
who has purchased the Nokia product(s) included in the sales package
(“Product”).
Nokia warrants to you that during the warranty period Nokia or a
Nokia authorized service company will in a commercially reasonable
time remedy defects in materials, design and workmanship free of
charge by repairing or, should Nokia in its absolute discretion deem it
necessary, replacing the Product in accordance with this Limited
Warranty (unless otherwise required by law). This Limited Warranty is
only valid and enforceable in the country where you have purchased
the Product provided that it is intended for sale in that country.
How to get warranty service
If you wish to make a claim under the Limited Warranty, you may call
the Nokia call center (where this is available and please note national
rates apply to calls) and/or where necessary, return your Product or the
affected part (if it is not the entire Product) to a Nokia care center or
Nokia designated service location. Information about Nokia care
centers, Nokia designated service locations and Nokia call centers can
be found at local Nokia web pages where available.
Warranty Period
The warranty period starts at the time of Product's original purchase by
the first end-user. The Product may consist of several different parts
and different parts may be covered by a different warranty period
(hereinafter “Warranty Period”). The different Warranty Periods are:
You must return your Product or the affected part (if it is not the entire
Product) to a Nokia care center or Nokia designated service location
before the expiry of the Warranty Period.
When making a Limited Warranty claim you have to present: a) the
Product (or affected part thereto), b) the legible and unmodified
original proof of purchase, which clearly indicates the name and
address of the seller, the date and place of purchase, the product type
and the IMEI or other serial number.
a) twelve (12) months for the mobile device and accessories (whether
included in the mobile device sales package or sold separately)
other than the consumable parts and accessories listed in (b) and
(c) below;
b) six (6) months for the following consumable parts and accessories:
batteries, chargers, desk stands, headsets, cables and covers; and
This Limited Warranty extends only to the original first end-user of the
Product and is not assignable or transferable to any subsequent
purchaser/end-user.
W1
What is not covered?
4. This Limited Warranty does not cover defects caused by the fact
that the battery has been short-circuited or by the fact that the
seals of the battery enclosure or the cells are broken or show
evidence of tampering or by the fact that the battery has been
used in equipment other than those for which it has been
specified.
1. This Limited Warranty does not cover user manuals or any third
party software, settings, content, data or links, whether included/
downloaded in the Product, whether included during installment,
assembly, shipping or at any other time in the delivery chain or
otherwise and in any way acquired by you. To the extent permitted
by applicable law(s), Nokia does not warrant that any Nokia
software will meet your requirements, will work in combination
with any hardware or software applications provided by a third
party, that the operation of the software will be uninterrupted or
error free or that any defects in the software are correctable or will
be corrected.
5. This Limited Warranty does not apply if the Product has been
opened, modified or repaired by anyone other than an authorized
service centre, if it is repaired using unauthorised spare parts or if
the Product’s serial number, the mobile accessory date code or the
IMEI number has been removed, erased, defaced, altered or are
illegible in any way and this shall be determined in the sole
discretion of Nokia.
2. This Limited Warranty does not cover a) normal wear and tear
(including, without limitation, wear and tear of camera lenses,
batteries or displays), b) transport costs, c) defects caused by rough
handling (including, without limitation, defects caused by sharp
items, by bending, compressing or dropping, etc.), d) defects or
damage caused by misuse of the Product, including use that is
contrary to the instructions provided by Nokia (e.g. as set out in the
Product's user guide) and/or e) other acts beyond the reasonable
control of Nokia.
6. This Limited Warranty does not apply if the Product has been
exposed to moisture, to dampness or to extreme thermal or
environmental conditions or to rapid changes in such conditions,
to corrosion, to oxidation, to spillage of food or liquid or to
influence from chemical products.
Other important notices
A third party, independent operator provides the SIM card and cellular
and/or other network or system on which the Product operates.
Therefore, Nokia will not accept responsibility under this warranty for
the operation, availability, coverage, services or range of the cellular or
other network or system. Before the Product can be repaired or
replaced, the operator may need to unlock any SIM-lock or other lock
that may have been added to lock the product to a specific network or
operator. Accordingly, Nokia does not accept responsibility for any
delays in warranty repairs or for the inability of Nokia to complete
warranty repairs that are caused by the operator's delay or failure to
unlock any SIM-lock or other lock.
3. This Limited Warranty does not cover defects or alleged defects
caused by the fact that the Product was used with, or connected to,
a product, accessories, software and/or service not manufactured,
supplied or authorized by Nokia or was used otherwise than for its
intended use. Defects can be caused by viruses from your or from a
third party's unauthorised access to services, other accounts,
computer systems or networks. This unauthorised access can take
place through hacking, password-mining or through a variety of
other means.
W2
Please remember to make back-up copies or keep written records of all
important content and data stored in your Product, because content
and data may be lost during repair or replacement of the Product.
Nokia, in a manner consistent with the provisions of the section
entitled “Limitation of Nokia's Liability” below, to the extent permitted
by applicable law(s), shall not under any circumstances be liable, either
expressly or impliedly, for any damages or losses of any kind
whatsoever resulting from loss of, damage to, or corruption of, content
or data during repair or replacement of the Product.
liability for loss of or damage to or corruption of data, for any loss of
profit, loss of use of Products or functionality, loss of business, loss of
contracts, loss of revenues or loss of anticipated savings, increased
costs or expenses or for any indirect loss or damage, consequential loss
or damage or special loss or damage. To the extent permitted by
applicable law, Nokia’s liability shall be limited to the purchase value of
the Product. The above limitations shall not apply to death or personal
injury resulting from Nokia’s proven negligence.
Statutory obligations
All parts of the Product or other equipment that Nokia has replaced
shall become the property of Nokia. If the returned Product is found
not to be covered by the terms and conditions of the Limited Warranty,
Nokia and its authorized service companies reserve the right to charge
a handling fee. When repairing or replacing the Product, Nokia may
use products or parts that are new, equivalent to new or
re-conditioned.
This Limited Warranty must be read subject to any statutory provisions
that imply warranties or conditions into this Limited Warranty that
cannot be excluded, restricted or modified or cannot be excluded,
restricted or modified except to a limited extent. If such statutory
provisions apply, to the extent to which Nokia is able to do so,
its liability under those provisions will be limited, at its option to, in the
case of goods: the replacement of the goods or the supply of equivalent
goods, the repair of the goods, the payment of the cost of replacing the
goods or of acquiring equivalent goods, or the payment of the cost of
having the goods repaired; and in the case of services: the supplying of
the services again or the payment of the cost of having the services
supplied again.
Your Product may contain country specific elements, including
software. If the Product has been re-exported from its original
destination country to another country, the Product may contain
country specific elements that are not considered to be a defect under
this Limited Warranty.
NOTE! Your Product is a sophisticated electronic device. Nokia strongly
encourages you to familiarize yourself with the user guide and
instructions provided with and for the Product. Please also note that the
Product might contain high precision displays, camera lenses and other
such parts, which could be scratched or otherwise damaged if not
handled very carefully.
Limitation of Nokia's liability
This Limited Warranty is your sole and exclusive remedy against Nokia
and Nokia's sole and exclusive liability in respect of defects in your
Product. However, this Limited Warranty shall neither exclude nor limit
i) any of your legal (statutory) rights under the applicable national
laws or ii) any of your rights against the seller of the Product.
All warranty information, product features and specifications are
subject to change without notice.
This Limited Warranty replaces all other Nokia warranties and
liabilities, whether oral, written, (non-mandatory) statutory,
contractual, in tort or otherwise, including, without limitation, and
where permitted by applicable law, any implied conditions, warranties
or other terms as to satisfactory quality or fitness for purpose. To the
extent permitted by applicable law(s) Nokia does not assume any
Nokia Corporation
Keilalahdentie 2-4
FIN-02150 Espoo
Finland
W3
Nokia Care Online
INTERACTIVE
DEMONSTRATIONS
The Nokia Care web support provides you with more information on our
online services.
INTERACTIVE DEMONSTRATIONS
Learn how to set up your phone for the first time, and find out more about its features.
Interactive Demonstrations give step-by-step instructions on using your phone.
SOFTWARE
USER’S GUIDE
The online User’s Guide contains detailed information on your phone. Remember
to check regularly for updates.
SOFTWARE
Make the most of your phone with software for your phone and PC. Nokia PC Suite
connects your phone and PC so you can manage your calendar, contacts, music and
images, while other applications complement its use.
SETTINGS
Certain phone functions, such as multimedia messaging, mobile browsing and email*,
may require settings before you can use them. Have them sent to your phone free
of charge.
USER’S GUIDE
*Not available on all phones.
SETTINGS
HOW DO I USE MY PHONE?
The Set Up section, at www.nokia-asia.com/setup, helps you prepare your phone for use. Familiarise yourself with
phone functions and features by referring to the Guides and Demos section at www.nokia-asia.com/guides.
HOW DO I SYNCHRONISE MY PHONE AND PC?
Connecting your phone to a compatible PC with the requisite Nokia PC Suite version from www.nokia-asia.com/pcsuite
lets you synchronise your calendar and contacts.
WHERE CAN I GET SOFTWARE FOR MY PHONE?
Get more out of your phone with downloads from the Software section at www.nokia-asia.com/software.
WHERE CAN I FIND ANSWERS TO COMMON QUESTIONS?
Look up the FAQ section at www.nokia-asia.com/faq for answers to your questions on your phone and other
Nokia products and services.
HOW DO I KEEP UP WITH NOKIA NEWS?
Subscribe online to Nokia Connections at www.nokia-asia.com/signup, and be the first to know about the latest products,
promotions and upcoming events.
Should you still require further assistance, please refer to www.nokia-asia.com/contactus.
For additional information on repair services, please visit www.nokia-asia.com/repair.
Please visit www.nokia-asia.com/support for details.
|