Product Manual
TM
Constellation.2 SAS
Standard Models
Self-Encrypting Drive Models
ST91000640SS
ST9500620SS
ST91000641SS
ST9500621SS
SED FIPS 140-2 Models
ST91000642SS
ST9500622SS
100620418
Rev. H
April 2012
Contents
Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Applicable standards and reference documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electromagnetic compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Standard features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Media description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Formatted capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programmable drive capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Factory-installed options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Internal drive characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Seek performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Access time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
General performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Start/stop time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Prefetch/multi-segmented cache control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cache operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Caching write data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Prefetch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reliability specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Error rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Recoverable Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Unrecoverable Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Seek errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Interface errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Reliability and service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Preventive maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Hot plugging the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
S.M.A.R.T. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Thermal monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Drive Self Test (DST). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Product warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Physical/electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.1
PowerChoiceTM power management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.1.1 PowerChoice reporting methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
AC power requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DC power requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.3.3
Conducted noise immunity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Power sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Current profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Constellation.2 SAS Product Manual, Rev. H
i
Power dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Environmental limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Relative humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Air cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Electromagnetic susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Mechanical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Power requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Drive internal defects/errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Drive error recovery procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Levels of PI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Drive orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Drive mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
task management responses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Inquiry data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Miscellaneous operating features and conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
ii
Constellation.2 SAS Product Manual, Rev. H
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Connector requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Electrical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
SAS transmitters and receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Signal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Ready LED Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Differential signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
12.7
SAS-2 Specification Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Additional information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Constellation.2 SAS Product Manual, Rev. H
iii
iv
Constellation.2 SAS Product Manual, Rev. H
List of Figures
Location of the HDA temperature check point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Figure 10. Example of FIPS tamper evidence labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Figure 11. Physical interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Figure 12. Air flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Figure 13. Physical interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Figure 14. SAS device plug dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Figure 15. SAS device plug dimensions (detail). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Constellation.2 SAS Product Manual, Rev. H
v
vi
Constellation.2 SAS Product Manual, Rev. H
1.0
Seagate Technology support services
SEAGATE ONLINE SUPPORT and SERVICES
For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/
Available services include:
Presales & Technical support
Global Support Services telephone numbers & business hours
Authorized Service Centers
For information regarding Warranty Support, visit
http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance
Constellation.2 SAS Product Manual, Rev. H
1
2.0
Scope
This manual describes Seagate Technology® LLC, Constellation.2TM SAS (Serial Attached SCSI) disk drives.
Constellation.2 SAS drives support the SAS Protocol specifications to the extent described in this manual. The
SAS Interface Manual (part number 100293071) describes the general SAS characteristics of this and other
Seagate SAS drives. The Self-Encrypting Drive Reference Manual, part number 100515636, describes the
interface, general operation, and security features available on Self-Encrypting Drive models.
Product data communicated in this manual is specific only to the model numbers listed in this manual. The data
listed in this manual may not be predictive of future generation specifications or requirements. If you are
designing a system which will use one of the models listed or future generation products and need further
assistance, please contact your Field Applications Engineer (FAE) or our global support services group as
Unless otherwise stated, the information in this manual applies to standard and Self-Encrypting Drive models.
Model Number
ST91000642SS
ST91000641SS
ST91000640SS
ST9500622SS
ST9500621SS
ST9500620SS
Self-Encrypting Drive (SED)
FIPS 140-2 Level 2
Yes
Yes
No
Yes
No
No
Yes
Yes
No
Yes
No
No
Note. Previous generations of Seagate Self-Encrypting Drive models were called Full Disk Encryption
(FDE) models before a differentiation between drive-based encryption and other forms of encryp-
tion was necessary.
Note. The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for
“Security of Data at Rest” based on the standards defined by the Trusted Computing Group (see
www.trustedcomputinggroup.org).
2
Constellation.2 SAS Product Manual, Rev. H
3.0
Applicable standards and reference documentation
The drives documented in this manual have been developed as system peripherals to the highest standards of
design and construction. The drives depends on host equipment to provide adequate power and environment
for optimum performance and compliance with applicable industry and governmental regulations. Special
attention must be given in the areas of safety, power distribution, shielding, audible noise control, and temper-
ature regulation. In particular, the drive must be securely mounted to guarantee the specified performance
3.1
Standards
The Constellation.2 family complies with Seagate standards as noted in the appropriate sections of this man-
ual and the Seagate SAS Interface Manual, part number 100293071.
The drives are recognized in accordance with UL 60950-1 as tested by UL, CSA 60950-1 as tested by CSA,
and EN60950-1 as tested by TUV.
The security features of Self-Encrypting Drive models are based on the “TCG Storage Architecture Core Spec-
ification” and the “TCG Storage Workgroup Security Subsystem Class: Enterprise_A” specification with addi-
tional vendor-unique features as noted in this product manual.
3.1.1
Electromagnetic compatibility
The drive, as delivered, is designed for system integration and installation into a suitable enclosure prior to
use. The drive is supplied as a subassembly and is not subject to Subpart B of Part 15 of the FCC Rules and
Regulations nor the Radio Interference Regulations of the Canadian Department of Communications.
The design characteristics of the drive serve to minimize radiation when installed in an enclosure that provides
reasonable shielding. The drive is capable of meeting the Class B limits of the FCC Rules and Regulations of
the Canadian Department of Communications when properly packaged; however, it is the user’s responsibility
to assure that the drive meets the appropriate EMI requirements in their system. Shielded I/O cables may be
required if the enclosure does not provide adequate shielding. If the I/O cables are external to the enclosure,
shielded cables should be used, with the shields grounded to the enclosure and to the host controller.
3.1.1.1
Electromagnetic susceptibility
As a component assembly, the drive is not required to meet any susceptibility performance requirements. It is
the responsibility of those integrating the drive within their systems to perform those tests required and design
their system to ensure that equipment operating in the same system as the drive or external to the system
Constellation.2 SAS Product Manual, Rev. H
3
3.1.2
Electromagnetic compliance
Seagate uses an independent laboratory to confirm compliance with the directives/standards for CE Marking
and C-Tick Marking. The drive was tested in a representative system for typical applications and comply with
the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. The selected
system represents the most popular characteristics for test platforms. The system configurations include:
• Typical current use microprocessor
• Keyboard
• Monitor/display
• Printer
• Mouse
Although the test system with this Seagate model complies with the directives/standards, we cannot guarantee
that all systems will comply. The computer manufacturer or system integrator shall confirm EMC compliance
and provide the appropriate marking for their product.
Electromagnetic compliance for the European Union
If this model has the CE Marking it complies with the European Union requirements of the Electromagnetic
Compatibility Directive 2004/108/EC as put into place on 20 July 2007.
Australian C-Tick
If this model has the C-Tick Marking it complies with the Australia/New Zealand Standard AS/NZ CISPR22 and
meets the Electromagnetic Compatibility (EMC) Framework requirements of Australia’s Spectrum Manage-
ment Agency (SMA).
Korean KCC
If these drives have the Korean Communications Commission (KCC) logo, they comply with KN22, KN 24, and
KN61000.
Taiwanese BSMI
If this model has the Taiwanese certification mark then it complies with Chinese National Standard, CNS13438.
4
Constellation.2 SAS Product Manual, Rev. H
3.1.3
European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemi-
cal substances, including Lead, Cadmium, Mercury, Hexavalent Chromium, PBB and PBDE, in electronic prod-
ucts, effective July 2006. This drive is manufactured with components and materials that comply with the RoHS
Directive.
A number of parts and materials in Seagate products are procured from external suppliers. We rely on the rep-
resentations of our suppliers regarding the presence of RoHS substances in these parts and materials. Our
supplier contracts require compliance with our chemical substance restrictions, and our suppliers document
their compliance with our requirements by providing material content declarations for all parts and materials for
the disk drives documented in this publication. Current supplier declarations include disclosure of the inclusion
of any RoHS-regulated substance in such parts or materials.
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws
and regulations which restrict chemical content in electronic products. These systems include standard operat-
ing procedures that ensure that restricted substances are not utilized in our manufacturing operations, labora-
tory analytical validation testing, and an internal auditing process to ensure that all standard operating
procedures are complied with.
3.1.4
China Restriction of Hazardous Substances (RoHS) Directive
This product has an Environmental Protection Use Period (EPUP) of 20 years. The following
table contains information mandated by China's "Marking Requirements for Control of Pollution
Caused by Electronic Information Products" Standard.
"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower
than the threshold defined by the China RoHS MCV Standard.
"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over
the threshold defined by the China RoHS MCV Standard.
Constellation.2 SAS Product Manual, Rev. H
5
3.2
Reference documents
SAS Interface Manual
Seagate part number: 100293071
SCSI Commands Reference Manual
Seagate part number: 100293068
Self-Encrypting Drives Reference Manual
Seagate part number: 100515636
ANSI SAS Documents
SFF-8223
SFF-8460
SFF-8470
SFF-8482
2.5” Drive Form Factor with Serial Connector
HSS Backplane Design Guidelines
Multi Lane Copper Connector
SAS Plug Connector
ANSI INCITS.xxx Serial Attached SCSI (SAS) Standard (T10/1562-D)
ISO/IEC 14776-xxx SCSI Architecture Model-3 (SAM-3) Standard (T10/1561-D)
ISO/IEC 14776-xxx SCSI Primary Commands-3 (SPC-3) Standard (T10/1416-D)
ISO/IEC 14776-xxx SCSI Block Commands-2 (SBC-2) Standard (T10/1417-D)
ANSI Small Computer System Interface (SCSI) Documents
X3.270-1996
(SCSI-3) Architecture Model
Trusted Computing Group (TCG) Documents (apply to Self-Encrypting Drive models only)
TCG Storage Architecture Core Specification, Rev. 1.0
TCG Storage Security Subsystem Class Enterprise Specification, Rev. 1.0
Specification for Acoustic Test Requirement and Procedures
Seagate part number: 30553-001
In case of conflict between this document and any referenced document, this document takes precedence.
6
Constellation.2 SAS Product Manual, Rev. H
4.0
General description
Constellation.2 drives provide high performance, high capacity data storage for a variety of systems including
engineering workstations, network servers, mainframes, and supercomputers. The Serial Attached SCSI inter-
face is designed to meet next-generation computing demands for performance, scalability, flexibility and high-
density storage requirements.
Constellation.2 drives are random access storage devices designed to support the Serial Attached SCSI Proto-
col as described in the ANSI specifications, this document, and the SAS Interface Manual (part number
100293071) which describes the general interface characteristics of this drive. Constellation.2 drives are clas-
sified as intelligent peripherals and provide level 2 conformance (highest level) with the ANSI SCSI-1 standard.
The SAS connectors, cables and electrical interface are compatible with Serial ATA (SATA), giving future users
the choice of populating their systems with either SAS or SATA hard disk drives. This allows you to continue to
leverage your existing investment in SCSI while gaining a 6Gb/s serial data transfer rate.
The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for “Security
group.org).
The head and disk assembly (HDA) is sealed at the factory. Air recirculates within the HDA through a non-
replaceable filter to maintain a contamination-free HDA environment.
Note. Never disassemble the HDA and do not attempt to service items in the sealed enclosure (heads,
media, actuator, etc.) as this requires special facilities. The drive does not contain user-replaceable
parts. Opening the HDA for any reason voids your warranty.
Constellation.2 drives use a dedicated load/unload zone at the outermost radius of the media to eliminate the
possibility of destroying or degrading data by landing in the data zone. The heads automatically go to the ramp
load/unload when power is removed from the drive.
An automatic shipping lock prevents potential damage to the heads and discs that results from movement dur-
ing shipping and handling. The shipping lock disengages and the head load process begins when power is
applied to the drive.
Constellation.2 drives decode track 0 location data from the servo data embedded on each surface to eliminate
mechanical transducer adjustments and related reliability concerns.
The drives also use a high-performance actuator assembly with a low-inertia, balanced, patented, straight arm
design that provides excellent performance with minimal power dissipation.
Constellation.2 SAS Product Manual, Rev. H
7
4.1
Standard features
Constellation.2 drives have the following standard features:
• Perpendicular recording technology
• 1.5 / 3 / 6 Gb Serial Attached SCSI (SAS) interface
• Integrated dual port SAS controller supporting the SCSI protocol
• Support for SAS expanders and fanout adapters
• Firmware downloadable using the SAS interface
• 128 - deep task set (queue)
• Supports up to 32 initiators
• Jumperless configuration.
• User-selectable logical block size (512, 520 or 528 bytes per logical block).
• SAS-SED models ST91000641SS and ST9500621SS.
• SAS-SED (FIPS 140-2) models ST91000642SS and ST9500622SS.
• Industry standard SFF 2.5-inch dimensions
• Programmable logical block reallocation scheme
• Flawed logical block reallocation at format time
• Programmable auto write and read reallocation
• Reallocation of defects on command (Post Format)
• ECC maximum burst correction length of 444 bits
• No preventive maintenance or adjustments required
• Embedded servo design
• Automatic shipping lock
• Dedicated head load/unload zone
• Self diagnostics performed when power is applied to the drive
• Zone bit recording (ZBR)
• Vertical, horizontal, or top down mounting
• Dynamic spindle brake
• Drive Self Test (DST)
• Background Media Scan (BMS)
• Idle Read After Write (IRAW)
• Power Save
Constellation.2 SAS Self-Encrypting Drive models have the following additional features:
• Automatic data encryption/decryption
• Controlled access
• Random number generator
• Drive locking
• 16 independent data bands
• Cryptographic erase of user data for a drive that will be repurposed or scrapped
• Authenticated firmware download
4.2
Media description
The media used on the drive has a glass substrate coated with a thin film magnetic material, overcoated with a
proprietary protective layer for improved durability and environmental protection.
8
Constellation.2 SAS Product Manual, Rev. H
4.3
Performance
• Programmable multi-segmentable cache buffer
• 600 MB/s maximum instantaneous data transfers.
• 7200 RPM spindle. Average latency = 4.16ms
• Background processing of queue
• Supports start and stop commands (spindle stops spinning)
• Adaptive seek velocity; improved seek performance
Note. There is no significant performance difference between Self-Encrypting Drive and standard (non-
Self-Encrypting Drive) models.
4.4
Reliability
• Annualized Failure Rate (AFR) of 0.62%
• Mean time between failures (MTBF) of 1,400,000 hours
• Balanced low mass rotary voice coil actuator
• Incorporates industry-standard Self-Monitoring Analysis and Reporting Technology (S.M.A.R.T.)
• 5-year warranty
4.5
Formatted capacities
Standard OEM models are formatted to 512 bytes per block. The block size is selectable at format time and
must be a multiple of 4 bytes. Users having the necessary equipment may modify the data block size before
issuing a format command and obtain different formatted capacities than those listed.
To provide a stable target capacity environment and at the same time provide users with flexibility if they
choose, Seagate recommends product planning in one of two modes:
1. Seagate designs specify capacity points at certain block sizes that Seagate guarantees current and future
products will meet. We recommend customers use this capacity in their project planning, as it ensures a
stable operating point with backward and forward compatibility from generation to generation. The current
guaranteed operating points for this product are:
Capacity (Blocks)
ST91000640SS, ST91000641SS &
ST91000642SS
ST9500620SS, ST9500621SS &
ST9500622SS
Sector Size
Decimal
Hex
Decimal
Hex
512
520
528
1,953,525,168
1,923,076,936
1,876,331,336
74706DB0
729FD348
6FD68B48
976,773,168
961,538,472
938,165,672
3A386030
394FE9A8
37EB45A8
4.6
Programmable drive capacity
Using the Mode Select command, the drive can change its capacity to something less than maximum. See the
Mode Select (6) parameter list table in the SAS Interface Manual, part number 100293071. A value of zero in
the Number of Blocks field indicates that the drive will not change the capacity it is currently formatted to have.
A number other than zero and less than the maximum number of LBAs in the Number of Blocks field changes
the total drive capacity to the value in the Number of Blocks field. A value greater than the maximum number of
LBAs is rounded down to the maximum capacity.
Constellation.2 SAS Product Manual, Rev. H
9
4.7
Factory-installed options
You may order the following items which are incorporated at the manufacturing facility during production or
packaged before shipping. Some of the options available are (not an exhaustive list of possible options):
• Other capacities can be ordered depending on sparing scheme and sector size requested.
• Single-unit shipping pack. The drive is normally shipped in bulk packaging to provide maximum protection
against transit damage. Units shipped individually require additional protection as provided by the single unit
shipping pack. Users planning single unit distribution should specify this option.
• The Safety and Regulatory Agency Specifications, part number 75789512, is usually included with each
standard OEM drive shipped, but extra copies may be ordered.
10
Constellation.2 SAS Product Manual, Rev. H
5.0
Performance characteristics
This section provides detailed information concerning performance-related characteristics and features of Con-
stellation.2 drives.
5.1
Internal drive characteristics
ST91000640SS
ST91000641SS
ST91000642SS
ST9500620SS
ST9500621SS
ST9500622SS
Drive capacity
1000
500
Gbytes (formatted, rounded off value)
Read/write data heads
Bytes per track
Bytes per surface
Tracks per surface (total)
Tracks per inch
8
4
732,998
125,069
165,800
270,000
1,544,000
417
732,998
125,069
165,800
270,000
1,544,000
417
Bytes (average, rounded off values)
MB (unformatted, rounded off value)
Tracks (user accessible)
TPI (average)
Peak bits per inch
Areal density
BPI
2
Gb/in
Internal data rate
Disk rotation speed
Avg rotational latency
84 - 163
7200
4.16
84 - 163
7200
4.16
MB/s (variable with zone)
rpm
ms
5.2
Seek performance characteristics
100293071) for additional timing details.
5.2.1
Access time
1 2
,
Including controller overhead
(ms)
Not including controller overhead1, 2
(ms)
Read
7.7
Write
8.7
Read
7.5
Write
8.5
3 4
,
Average
Typical
Single track
Full stroke
Typical3,4
Typical3,4
0.23
17.26
0.44
18.28
0.23
17.06
0.44
18.08
1.
2.
3.
Execution time measured from receipt of the Command to the Response.
Assumes no errors and no sector has been relocated.
Typical access times are measured under nominal conditions of temperature, voltage, and horizontal orientation as
measured on a representative sample of drives.
4.
Access time = controller overhead + average seek time and applies to all data transfer commands.
Access to data = access time + latency time.
Constellation.2 SAS Product Manual, Rev. H
11
5.2.2
Format command execution time for 512-byte sectors (minutes)
1TB models
384
500GB models
188
94
Maximum (with verify)
192
Maximum (without verify)
Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the request
for a Status Byte Transfer to the Initiator (excluding connect/disconnect).
When changing sector sizes, the format times shown above may need to be increased by 30 minutes.
5.2.3
General performance characteristics
Minimum sector interleave
1 to 1
Data buffer to/from disk media (one 512-byte logical block)*
Sustained transfer rate
84 to 163 MB/s
105 to 115 MB/s
SAS Interface maximum instantaneous transfer rate
600 MB/s* per port
(dual port = 1200 MB/s*)
Logical block sizes
512 (default), 520 or 528.
Read/write consecutive sectors on a track
Yes
Flaw reallocation performance impact (for flaws reallocated at format time using the
spare sectors per sparing zone reallocation scheme.)
Negligible
Average rotational latency
4.16ms
*Assumes no errors and no relocated logical blocks. Rate measured from the start of the first logical block transfer to or
from the host.
5.3
Start/stop time
The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has
been applied.
If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START
STOP UNIT command with the START bit equal to 0, the drive becomes ready for normal operations within 20
seconds (excluding the error recovery procedure).
If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY
(ENABLE SPINUP) primitive, the drive waits for a START STOP UNIT command with the START bit equal to 1.
After receiving a START STOP UNIT command with the START bit equal to 1, the drive waits for a NOTIFY
(ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the
drive becomes ready for normal operations within 20 seconds (excluding the error recovery procedure).
If the drive receives a START STOP UNIT command with the START bit and IMMED bit equal to 1 and does
not receive a NOTIFY (ENABLE SPINUP) primitive within 5 seconds, the drive fails the START STOP UNIT
command.
The START STOP UNIT command may be used to command the drive to stop the spindle. Stop time is 20 sec-
onds (maximum) from removal of DC power. SCSI stop time is 20 seconds. There is no power control switch
on the drive.
12
Constellation.2 SAS Product Manual, Rev. H
5.4
Prefetch/multi-segmented cache control
The drive provides a prefetch (read look-ahead) and multi-segmented cache control algorithms that in many
cases can enhance system performance. Cache refers to the drive buffer storage space when it is used in
cache operations. To select this feature, the host sends the Mode Select command with the proper values in
the applicable bytes in page 08h. Prefetch and cache operations are independent features from the standpoint
that each is enabled and disabled independently using the Mode Select command; however, in actual opera-
All default cache and prefetch mode parameter values (Mode Page 08h) for standard OEM versions of this
5.5
Cache operation
Note. Refer to the SAS Interface Manual for more detail concerning the cache bits.
Of the 64MB physical buffer space in the drive, approximately 30,000 kbytes are available as a data cache.
The remaining buffer space is reserved for internal drive use. The buffer is divided into logical segments from
which data is read and to which data is written.
The drive keeps track of the logical block addresses of the data stored in each segment of the buffer. If the
cache is enabled (see RCD bit in the SAS Interface Manual), data requested by the host with a read command
is retrieved from the buffer, if possible, before any disk access is initiated. If cache operation is not enabled, the
buffer is still used, but only as circular buffer segments during disk medium read operations (disregarding
Prefetch operation for the moment). That is, the drive does not check in the buffer segments for the requested
read data, but goes directly to the medium to retrieve it. The retrieved data merely passes through some buffer
segment on the way to the host. All data transfers to the host are in accordance with buffer-full ratio rules. See
the explanation provided with the information about Mode Page 02h (disconnect/reconnect control) in the SAS
Interface Manual.
The following is a simplified description of the prefetch/cache operation:
Case A—read command is received and all of the requested logical blocks are already in the cache:
1. Drive transfers the requested logical blocks to the initiator.
Case B—A Read command requests data, and at least one requested logical block is not in any segment of
the cache:
1. The drive fetches the requested logical blocks from the disk and transfers them into a segment, and then
from there to the host in accordance with the Mode Select Disconnect/Reconnect parameters, page 02h.
Each cache segment is actually a self-contained circular buffer whose length is an integer number of logical
blocks. The drive dynamically creates and removes segments based on the workload. The wrap-around capa-
bility of the individual segments greatly enhances the cache’s overall performance.
Note. The size of each segment is not reported by Mode Sense command page 08h, bytes 14 and 15.
The value 0XFFFF is always reported regardless of the actual size of the segment. Sending a size
specification using the Mode Select command (bytes 14 and 15) does not set up a new segment
size. If the STRICT bit in Mode page 00h (byte 2, bit 1) is set to one, the drive responds as it does
for any attempt to change an unchangeable parameter.
Constellation.2 SAS Product Manual, Rev. H
13
5.5.1
Caching write data
Write caching is a write operation by the drive that makes use of a drive buffer storage area where the data to
be written to the medium is stored while the drive performs the Write command.
If read caching is enabled (RCD=0), then data written to the medium is retained in the cache to be made avail-
able for future read cache hits. The same buffer space and segmentation is used as set up for read functions.
The buffer segmentation scheme is set up or changed independently, having nothing to do with the state of
RCD. When a write command is issued, if RCD=0, the cache is first checked to see if any logical blocks that
are to be written are already stored in the cache from a previous read or write command. If there are, the
respective cache segments are cleared. The new data is cached for subsequent Read commands.
If the number of write data logical blocks exceed the size of the segment being written into, when the end of the
segment is reached, the data is written into the beginning of the same cache segment, overwriting the data that
was written there at the beginning of the operation; however, the drive does not overwrite data that has not yet
been written to the medium.
If write caching is enabled (WCE=1), then the drive may return Good status on a write command after the data
has been transferred into the cache, but before the data has been written to the medium. If an error occurs
while writing the data to the medium, and Good status has already been returned, a deferred error will be gen-
erated.
The Synchronize Cache command may be used to force the drive to write all cached write data to the medium.
Upon completion of a Synchronize Cache command, all data received from previous write commands will have
5.5.2
Prefetch operation
If the Prefetch feature is enabled, data in contiguous logical blocks on the disk immediately beyond that which
was requested by a Read command are retrieved and stored in the buffer for immediate transfer from the buf-
fer to the host on subsequent Read commands that request those logical blocks (this is true even if cache
operation is disabled). Though the prefetch operation uses the buffer as a cache, finding the requested data in
the buffer is a prefetch hit, not a cache operation hit.
To enable Prefetch, use Mode Select page 08h, byte 12, bit 5 (Disable Read Ahead - DRA bit). DRA bit = 0
enables prefetch.
The drive does not use the Max Prefetch field (bytes 8 and 9) or the Prefetch Ceiling field (bytes 10 and 11).
When prefetch (read look-ahead) is enabled (enabled by DRA = 0), the drive enables prefetch of contiguous
blocks from the disk when it senses that a prefetch hit will likely occur. The drive disables prefetch when it
decides that a prefetch hit is not likely to occur.
14
Constellation.2 SAS Product Manual, Rev. H
6.0
Reliability specifications
The following reliability specifications assume correct host and drive operational interface, including all inter-
face timings, power supply voltages, environmental requirements and drive mounting constraints.
Seek error rate:
Less than 10 errors in 108 seeks
1
Read Error Rates
Recovered Data
Unrecovered Data
Miscorrected Data
Less than 10 errors in 1012 bits transferred (OEM default settings)
Less than 1 sector in 1015 bits transferred
Less than 1 sector in 1021 bits transferred
Less than 1 error in 1012 bits transferred
1,400,000 hours
Interface error rate:
Mean Time Between Failure (MTBF):
Annualized Failure Rate (AFR):
Preventive maintenance:
0.62%
None required
1.
Error rate specified with automatic retries and data correction with ECC enabled and all flaws reallocated.
6.1
Error rates
The error rates stated in this manual assume the following:
• The drive is operated in accordance with this manual using DC power as defined in paragraph 7.3, "DC
• Errors caused by host system failures are excluded from error rate computations.
• Assume random data.
• Default OEM error recovery settings are applied. This includes AWRE, ARRE, full read retries, full write
retries and full retry time.
6.1.1
Recoverable Errors
Recoverable errors are those detected and corrected by the drive, and do not require user intervention.
Recoverable Data errors will use correction, although ECC on-the-fly is not considered for purposes of recov-
ered error specifications.
Recovered Data error rate is determined using read bits transferred for recoverable errors occurring during a
read, and using write bits transferred for recoverable errors occurring during a write.
6.1.2
Unrecoverable Errors
An unrecoverable data error is defined as a failure of the drive to recover data from the media. These errors
occur due to head/media or write problems. Unrecoverable data errors are only detected during read opera-
tions, but not caused by the read. If an unrecoverable data error is detected, a MEDIUM ERROR (03h) in the
Sense Key will be reported. Multiple unrecoverable data errors resulting from the same cause are treated as 1
error.
Constellation.2 SAS Product Manual, Rev. H
15
6.1.3
Seek errors
A seek error is defined as a failure of the drive to position the heads to the addressed track. After detecting an
initial seek error, the drive automatically performs an error recovery process. If the error recovery process fails,
a seek positioning error (Error code = 15h or 02h) will be reported with a Hardware error (04h) in the Sense
8
Key. Recoverable seek errors are specified at Less than 10 errors in 10 seeks. Unrecoverable seek errors
(Sense Key = 04h) are classified as drive failures.
6.1.4
Interface errors
An interface error is defined as a failure of the receiver on a port to recover the data as transmitted by the
device port connected to the receiver. The error may be detected as a running disparity error, illegal code, loss
of word sync, or CRC error.
6.2
Reliability and service
You can enhance the reliability of Constellation.2 disk drives by ensuring that the drive receives adequate cool-
6.2.1
Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)
The production disk drive shall achieve an AFR of 0.62% (MTBF of 1,400,000 hours) when operated in an
the MTBF). The AFR (MTBF) is a population statistic not relevant to individual units.
The AFR (MTBF) specification is based on the following assumptions for Enterprise Storage System environ-
ments:
• 8760 power-on hours per year.
• 250 average on/off cycles per year.
• Operations at nominal voltages.
• Systems will provide adequate cooling to ensure the case temperatures specified in Section 7.5 are not
decrease the MTBF.
6.2.2
Preventive maintenance
No routine scheduled preventive maintenance is required.
6.2.3
Hot plugging the drive
When a disk is powered on by switching the power or hot plugged, the drive runs a self test before attempting
to communicate on its’ interfaces. When the self test completes successfully, the drive initiates a Link Reset
starting with OOB. An attached device should respond to the link reset. If the link reset attempt fails, or any
time the drive looses sync, the drive initiated link reset. The drive will initiate link reset once per second but
alternates between port A and B. Therefore each port will attempt a link reset once per 2 seconds assuming
both ports are out of sync.
If the self-test fails, the drive does not respond to link reset on the failing port.
Note. It is the responsibility of the systems integrator to assure that no temperature, energy, voltage haz-
ard, or ESD potential hazard is presented during the hot connect/disconnect operation. Discharge
the static electricity from the drive carrier prior to inserting it into the system.
16
Constellation.2 SAS Product Manual, Rev. H
Caution. The drive motor must come to a complete stop prior to changing the plane of operation. This time is
required to insure data integrity.
6.2.4
S.M.A.R.T.
S.M.A.R.T. is an acronym for Self-Monitoring Analysis and Reporting Technology. This technology is intended
to recognize conditions that indicate imminent drive failure and is designed to provide sufficient warning of a
failure to allow you to back up the data before an actual failure occurs.
Note. The drive’s firmware monitors specific attributes for degradation over time but can’t predict instanta-
neous drive failures.
Each monitored attribute has been selected to monitor a specific set of failure conditions in the operating per-
formance of the drive and the thresholds are optimized to minimize “false” and “failed” predictions.
Controlling S.M.A.R.T.
The operating mode of S.M.A.R.T. is controlled by the DEXCPT and PERF bits on the Informational Exceptions
Control mode page (1Ch). Use the DEXCPT bit to enable or disable the S.M.A.R.T. feature. Setting the DEX-
CPT bit disables all S.M.A.R.T. functions. When enabled, S.M.A.R.T. collects on-line data as the drive performs
normal read and write operations. When the PERF bit is set, the drive is considered to be in “On-line Mode
Only” and will not perform off-line functions.
You can measure off-line attributes and force the drive to save the data by using the Rezero Unit command.
Forcing S.M.A.R.T. resets the timer so that the next scheduled interrupt is in two hours.
You can interrogate the drive through the host to determine the time remaining before the next scheduled mea-
surement and data logging process occurs. To accomplish this, issue a Log Sense command to log page 0x3E.
This allows you to control when S.M.A.R.T. interruptions occur. Forcing S.M.A.R.T. with the RTZ command
resets the timer.
Performance impact
S.M.A.R.T. attribute data is saved to the disk so that the events that caused a predictive failure can be recre-
ated. The drive measures and saves parameters once every two hours subject to an idle period on the drive
interfaces. The process of measuring off-line attribute data and saving data to the disk is uninterruptable. The
maximum on-line only processing delay is summarized below:
Maximum processing delay
On-line only delay
Fully-enabled delay
DEXCPT = 0, PERF = 1
DEXCPT = 0, PERF = 0
S.M.A.R.T. delay times
235 milliseconds
650 milliseconds
Reporting control
Reporting is controlled by the MRIE bits in the Informational Exceptions Control mode page (1Ch). Subject to
the reporting method, the firmware will issue to the host an 01-5Dxx sense code. The error code is preserved
through bus resets and power cycles.
Determining rate
S.M.A.R.T. monitors the rate at which errors occur and signals a predictive failure if the rate of degraded errors
increases to an unacceptable level. To determine rate, error events are logged and compared to the number of
total operations for a given attribute. The interval defines the number of operations over which to measure the
rate. The counter that keeps track of the current number of operations is referred to as the Interval Counter.
Constellation.2 SAS Product Manual, Rev. H
17
S.M.A.R.T. measures error rates. All errors for each monitored attribute are recorded. A counter keeps track of
the number of errors for the current interval. This counter is referred to as the Failure Counter.
Error rate is the number of errors per operation. The algorithm that S.M.A.R.T. uses to record rates of error is to
set thresholds for the number of errors and their interval. If the number of errors exceeds the threshold before
the interval expires, the error rate is considered to be unacceptable. If the number of errors does not exceed
the threshold before the interval expires, the error rate is considered to be acceptable. In either case, the inter-
val and failure counters are reset and the process starts over.
Predictive failures
S.M.A.R.T. signals predictive failures when the drive is performing unacceptably for a period of time. The firm-
ware keeps a running count of the number of times the error rate for each attribute is unacceptable. To accom-
plish this, a counter is incremented each time the error rate is unacceptable and decremented (not to exceed
zero) whenever the error rate is acceptable. If the counter continually increments such that it reaches the pre-
dictive threshold, a predictive failure is signaled. This counter is referred to as the Failure History Counter.
There is a separate Failure History Counter for each attribute.
6.2.5
Thermal monitor
Constellation.2 drives implement a temperature warning system which:
1. Signals the host if the temperature exceeds a value which would threaten the drive.
2. Signals the host if the temperature exceeds a user-specified value.
3. Saves a S.M.A.R.T. data frame on the drive which exceeds the threatening temperature value.
A temperature sensor monitors the drive temperature and issues a warning over the interface when the tem-
perature exceeds a set threshold. The temperature is measured at power-up and then at ten-minute intervals
after power-up.
The thermal monitor system generates a warning code of 01-0B01 when the temperature exceeds the speci-
fied limit in compliance with the SCSI standard. The drive temperature is reported in the FRU code field of
mode sense data. You can use this information to determine if the warning is due to the temperature exceeding
the drive threatening temperature or the user-specified temperature.
This feature is controlled by the Enable Warning (EWasc) bit, and the reporting mechanism is controlled by the
Method of Reporting Informational Exceptions field (MRIE) on the Informational Exceptions Control (IEC)
mode page (1Ch).
The current algorithm implements two temperature trip points. The first trip point is set at 68°C. The second trip
point is user-selectable using the Log Select command. The reference temperature parameter in the tempera-
you can set it to any value in the range of 0 to 68°C. If you specify a temperature greater than 68°C in this field,
the temperature is rounded down to 68°C. A sense code is sent to the host to indicate the rounding of the
parameter field.
Table 1:
Temperature Log Page (0Dh)
Parameter Code
0000h
Description
Primary Temperature
Reference Temperature
0001h
18
Constellation.2 SAS Product Manual, Rev. H
6.2.6
Drive Self Test (DST)
Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a
failed unit. DST validates the functionality of the drive at a system level.
There are two test coverage options implemented in DST:
1. Extended test
2. Short test
The most thorough option is the extended test that performs various tests on the drive and scans every logical
block address (LBA) of the drive. The short test is time-restricted and limited in length—it does not scan the
entire media surface, but does some fundamental tests and scans portions of the media.
If DST encounters an error during either of these tests, it reports a fault condition. If the drive fails the test,
remove it from service and return it to Seagate for service.
6.2.6.1
DST failure definition
The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log
page if a functional failure is encountered during DST. The channel and servo parameters are not modified to
test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes
are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number
of retries required to recover the data.
The following conditions are considered DST failure conditions:
• Seek error after retries are exhausted
• Track-follow error after retries are exhausted
• Read error after retries are exhausted
• Write error after retries are exhausted
Recovered errors will not be reported as diagnostic failures.
6.2.6.2
Implementation
This section provides all of the information necessary to implement the DST function on this drive.
6.2.6.2.1
State of the drive prior to testing
The drive must be in a ready state before issuing the Send Diagnostic command. There are multiple reasons
why a drive may not be ready, some of which are valid conditions, and not errors. For example, a drive may be
in process of doing a format, or another DST. It is the responsibility of the host application to determine the “not
ready” cause.
While not technically part of DST, a Not Ready condition also qualifies the drive to be returned to Seagate as a
failed drive.
A Drive Not Ready condition is reported by the drive under the following conditions:
• Motor will not spin
• Motor will not lock to speed
• Servo will not lock on track
• Drive cannot read configuration tables from the disk
In these conditions, the drive responds to a Test Unit Ready command with an 02/04/00 or 02/04/03 code.
6.2.6.2.2
Invoking DST
To invoke DST, submit the Send Diagnostic command with the appropriate Function Code (001b for the short
test or 010b for the extended test) in bytes 1, bits 5, 6, and 7.
Constellation.2 SAS Product Manual, Rev. H
19
6.2.6.2.3
Short and extended tests
DST has two testing options:
1. short
2. extended
These testing options are described in the following two subsections.
Each test consists of three segments: an electrical test segment, a servo test segment, and a read/verify scan
segment.
Short test (Function Code: 001b)
The purpose of the short test is to provide a time-limited test that tests as much of the drive as possible within
120 seconds. The short test does not scan the entire media surface, but does some fundamental tests and
scans portions of the media. A complete read/verify scan is not performed and only factual failures will report a
fault condition. This option provides a quick confidence test of the drive.
Extended test (Function Code: 010b)
The objective of the extended test option is to empirically test critical drive components. For example, the seek
tests and on-track operations test the positioning mechanism. The read operation tests the read head element
and the media surface. The write element is tested through read/write/read operations. The integrity of the
media is checked through a read/verify scan of the media. Motor functionality is tested by default as a part of
these tests.
The anticipated length of the Extended test is reported through the Control Mode page.
6.2.6.2.4
Log page entries
When the drive begins DST, it creates a new entry in the Self-test Results Log page. The new entry is created
by inserting a new self-test parameter block at the beginning of the self-test results log parameter section of the
log page. Existing data will be moved to make room for the new parameter block. The drive reports 20 param-
eter blocks in the log page. If there are more than 20 parameter blocks, the least recent parameter block will be
deleted. The new parameter block will be initialized as follows:
1. The Function Code field is set to the same value as sent in the DST command
2. The Self-Test Results Value field is set to Fh
3. The drive will store the log page to non-volatile memory
After a self-test is complete or has been aborted, the drive updates the Self-Test Results Value field in its Self-
Test Results Log page in non-volatile memory. The host may use Log Sense to read the results from up to the
last 20 self-tests performed by the drive. The self-test results value is a 4-bit field that reports the results of the
test. If the field is set to zero, the drive passed with no errors detected by the DST. If the field is not set to zero,
the test failed for the reason reported in the field.
The drive will report the failure condition and LBA (if applicable) in the Self-test Results Log parameter. The
Sense key, ASC, ASCQ, and FRU are used to report the failure condition.
6.2.6.2.5
Abort
There are several ways to abort a diagnostic. You can use a SCSI Bus Reset or a Bus Device Reset message
to abort the diagnostic.
You can abort a DST executing in background mode by using the abort code in the DST Function Code field.
This will cause a 01 (self-test aborted by the application client) code to appear in the self-test results values
log. All other abort mechanisms will be reported as a 02 (self-test routine was interrupted by a reset condition).
20
Constellation.2 SAS Product Manual, Rev. H
6.2.7
Product warranty
Shipping
When transporting or shipping a drive, use only a Seagate-approved container. Keep your original box. Sea-
gate approved containers are easily identified by the Seagate Approved Package label. Shipping a drive in a
non-approved container voids the drive warranty.
Seagate repair centers may refuse receipt of components improperly packaged or obviously damaged in tran-
sit. Contact your authorized Seagate distributor to purchase additional boxes. Seagate recommends shipping
by an air-ride carrier experienced in handling computer equipment.
Storage
The maximum recommended storage period for the drive in a non-operational environment is 90 days. Drives
should be stored in the original unopened Seagate shipping packaging whenever possible. Once the drive is
removed from the Seagate original packaging the recommended maximum period between drive operation
cycles is 30 days. During any storage period the drive non-operational temperature, humidity, wet bulb, atmo-
spheric conditions, shock, vibration, magnetic and electrical field specifications should be followed.
Product repair and return information
Seagate customer service centers are the only facilities authorized to service Seagate drives. Seagate does
not sanction any third-party repair facilities. Any unauthorized repair or tampering with the factory seal voids
the warranty.
Constellation.2 SAS Product Manual, Rev. H
21
7.0
Physical/electrical specifications
This section provides information relating to the physical and electrical characteristics of the drive.
7.1
PowerChoiceTM power management
Drives using the load/unload architecture provide programmable power management to tailor systems for per-
formance and greater energy efficiency.
The table below lists the supported PowerChoice modes. The further you go down in the table, the more power
savings you get. For example, Idle2 mode results in greater power savings than Idle1 mode. Standby mode
results in the greatest power savings.
PowerChoice modes
Mode
Description
Idle_A
Reduced electronics
Idle_B
Heads unloaded. Disks spinning at full RPM
Heads unloaded. Disks spinning at reduced RPM
Idle_C
Standby_Y
Heads unloaded. Disks spinning at reduced RPM.
Recovery requires the NOTIFY (Enable Spinup) command.
Standby_Z
Heads unloaded. Motor stopped (disks not spinning)
Recovery requires the NOTIFY (Enable Spinup) command.
PowerChoiceTM can be invoked using one of these two methods:
• Power Condition mode page method—Enable and initialize the idle condition timers and/or the standby con-
dition timers. The timer values are based on the values set in the Power Condition mode page.
• START STOP UNIT command method—Use the START STOP UNIT command (OPERATION CODE 1Bh).
This allows the host to directly transition the drive to any supported PowerChoice mode.
If both the Power Condition mode page and START STOP UNIT command methods are used, the START
STOP UNIT command request takes precedence over the Power Condition mode page power control and may
disable the idle condition and standby condition timers. The REQUEST SENSE command reports the current
PowerChoice state if active and also the method by which the drive entered the PowerChoice state.
When the drive receives a command, all power condition timers are suspended if they were enabled via the
Power Condition mode page. Once all outstanding commands are processed, the power condition timers are
reinitialized to the values defined in the Power Condition mode page.
22
Constellation.2 SAS Product Manual, Rev. H
7.1.1
PowerChoice reporting methods
PowerChoiceTM provides these reporting methods for tracking purposes:
Request Sense command reports
• Current power condition
• Method of entry
Note. Processing the Request Sense command does not impact the drive’s power save state.
Mode Sense command reports (mode page 0x1A)
• Idle conditions enabled / disabled
• Idle condition timer values (100ms increments) (default, saved, current, changeable)
Power Condition Vital Product Data (VPD) Page (VPD page 0x8A)
• Supported power conditions
• Typical recovery time from power conditions (1ms increments)
Start/Stop Cycle Counter Log Page reports (log page 0x0E)
• Specified and accumulated Start/Stops and Load/Unload cycles
Power Condition Transitions Log Page reports (log page 0x1A, subpage 0x00)
• Accumulated transitions to Active, Idle1, Idle2, Idle3, Standby2, Standby
7.2
AC power requirements
None.
7.3
DC power requirements
The voltage and current requirements for a single drive are shown below. Values indicated apply at the drive
connector.
The standard drive models and the SED drive models have identical hardware, however the security and
encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a
small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in
power consumption. There is no additional drain on the 12V supply.
Constellation.2 SAS Product Manual, Rev. H
23
Table 3:
500GB drive (Standard & SED model) DC power requirements
[1] Measured with average reading DC ammeter.
[2] Instantaneous +12V current peaks will exceed these values.
[3] Power supply at nominal voltage. N (number of drives tested) = 6, 35 Degrees C ambient.
[4] For +12 V, a –10% tolerance is allowed during initial spindle start but must return to ±5% before reaching
7,200 RPM. The ±5% must be maintained after the drive signifies that its power-up sequence has been
completed and that the drive is able to accept selection by the host initiator.
[6] This condition occurs after OOB and Speed Negotiation completes but before the drive has received the
Notify Spinup primitive.
[7] See paragraph 7.3.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and
transient response.
[8] Operating condition is defined as random 8 block reads.
[9] During idle, the drive heads are relocated every 30 seconds to a random location within the band from
three-quarters to maximum track.
Constellation.2 SAS Product Manual, Rev. H
25
General DC power requirement notes.
1. Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current
shown.
2. The +5V and +12V supplies should employ separate ground returns.
3. Where power is provided to multiple drives from a common supply, careful consideration for individual
drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak
starting current must be available to each device.
4. Parameters, other than spindle start, are measured after a 10-minute warm up.
5. No terminator power.
7.3.1
Conducted noise immunity
Noise is specified as a periodic and random distribution of frequencies covering a defined frequency range.
Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power
connector.
+5v
=
=
250mVpp from 100Hz to 20MHz.
+12v
450mVpp from 100Hz to 100KHz.
250mVpp from 100KHz to 20MHz.
150mVpp from 20MHz to 100MHz.
7.3.2
Power sequencing
The drive does not require power sequencing. The drive protects against inadvertent writing during power-up
and down.
26
Constellation.2 SAS Product Manual, Rev. H
7.4
Power dissipation
1TB model drive in 3Gb operation
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 3.
1TB Models (3Gb) DC current and power vs. input/output operations per second
Note. For power details about SED vs. non-SED drive, please refer to section 7.8.
Constellation.2 SAS Product Manual, Rev. H
29
1TB model drive in 6Gb operation
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 4.
1TB Models (6Gb) DC current and power vs. input/output operations per second
For power details about SED vs. non-SED drive, please refer to section 7.8.
30
Constellation.2 SAS Product Manual, Rev. H
500GB model drive in 3Gb operation
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 5.
500GB Models (3Gb) DC current and power vs. input/output operations per second
Note. For power details about SED vs. non-SED drive, please refer to section 7.8.
Constellation.2 SAS Product Manual, Rev. H
31
500GB model drive in 6Gb operation
volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by
3.4123.
Figure 6.
500GB Models (6Gb) DC current and power vs. input/output operations per second
For power details about SED vs. non-SED drive, please refer to section 7.8.
32
Constellation.2 SAS Product Manual, Rev. H
7.5
Environmental limits
Temperature and humidity values experienced by the drive must be such that condensation does not occur on
any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F
(14.8°C). Maximum wet bulb temperature is 82°F (28°C).
7.5.1
Temperature
a. Operating
The drive meets the operating specifications over a 41°F to 140°F (5°C to 60°C) drive case temperature
range with a maximum temperature gradient of 36°F (20°C) per hour.
The maximum allowable drive case temperature is 60°C. See Figure 7 for HDA case temperature measure-
ment location
The MTBF specification for the drive assumes the operating environment is designed to maintain nominal
case temperature. The rated MTBF is based upon a sustained case temperature of 104°F (40°C). Occa-
sional excursions in operating temperature between the rated MTBF temperature and the maximum drive
operating case temperature may occur without impact to the rated MTBF temperature. However continual
or sustained operation at case temperatures beyond the rated MTBF temperature will degrade the drive
MTBF and reduce product reliability.
Air flow may be required to achieve consistent nominal case temperature values (see Section 11.2). To con-
firm that the required cooling is provided for the electronics and HDA, place the drive in its final mechanical
configuration, and perform random write/read operations. After the temperatures stabilize, measure the
case temperature of the drive.
b. Non-operating
–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This
specification assumes that the drive is packaged in the shipping container designed by Seagate for use with
drive.
HDA Temp.
Check Point
Figure 7.
Location of the HDA temperature check point
Note. Image is for reference only, may not represent actual drive.
7.5.2 Relative humidity
The values below assume that no condensation on the drive occurs.
a. Operating
5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour.
b. Non-operating
5% to 95% non-condensing relative humidity.
Constellation.2 SAS Product Manual, Rev. H
33
7.5.3
Effective altitude (sea level)
a. Operating
–200 to +10,000 feet (–61 to +3,048 meters)
b. Non-operating
–200 to +40,000 feet (–61 to +12,210 meters)
7.5.4
Shock and vibration
Shock and vibration limits specified in this document are measured directly on the drive chassis. If the drive is
installed in an enclosure to which the stated shock and/or vibration criteria is applied, resonances may occur
internally to the enclosure resulting in drive movement in excess of the stated limits. If this situation is apparent,
it may be necessary to modify the enclosure to minimize drive movement.
The limits of shock and vibration defined within this document are specified with the drive mounted by any of
side nearest the LED may be up or down.
7.5.4.1
Shock
a. Operating—normal
The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not
exceeding 15 Gs at a maximum duration of 11ms (half sinewave). The drive, as installed for normal opera-
tion, shall operate error free while subjected to intermittent shock not exceeding 25 Gs at a maximum dura-
tion of 2ms (half sinewave). Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more
than once every 2 seconds.
b. Operating—abnormal
Equipment, as installed for normal operation, does not incur physical damage while subjected to intermit-
tent shock not exceeding 40 Gs at a maximum duration of 11ms (half sinewave). Shock occurring at abnor-
mal levels may promote degraded operational performance during the abnormal shock period. Specified
operational performance will continue when normal operating shock levels resume. The drive in abnormal
operation may report recoverable errors to host while subjected to intermittent shock not exceeding 70 Gs
for Read / 40 Gs for Write at a maximum duration of 2ms (half sinewave). Shock may be applied in the X, Y,
or Z axis. Shock is not to be repeated more than once every 2 seconds.
c. Non-operating
The limits of non-operating shock shall apply to all conditions of handling and transportation. This includes
both isolated drives and integrated drives.
The drive subjected to nonrepetitive shock not exceeding 80 Gs at a maximum duration of 11ms (half sine-
wave) shall not exhibit device damage or performance degradation. Shock may be applied in the X, Y, or Z
axis.
The drive subjected to nonrepetitive shock not exceeding 400 Gs at a maximum duration of 2ms (half sine-
wave) does not exhibit device damage or performance degradation. Shock may be applied in the X, Y, or Z
axis.
The drive subjected to nonrepetitive shock not exceeding 200 Gs at a maximum duration of 0.5ms (half sin-
ewave) does not exhibit device damage or performance degradation. Shock may be applied in the X, Y, or
Z axis.
34
Constellation.2 SAS Product Manual, Rev. H
d. Packaged
Seagate finished drive bulk packs are designed and tested to meet or exceed applicable ISTA and ASTM
standards. Volume finished drives will be shipped from Seagate factories on pallets to minimize freight
costs and ease material handling. Seagate finished drive bulk packs may be shipped individually. For less
than full shipments, instructions are printed on the bulk pack carton for minimum drive quantities and proper
drive placement.
X
X
Figure 8.
Recommended mounting
Note. Image is for reference only, may not represent actual drive.
Constellation.2 SAS Product Manual, Rev. H
35
7.5.4.2
Vibration
a. Operating—normal
The drive as installed for normal operation, shall comply with the complete specified performance while
subjected to continuous vibration not exceeding
5 - 500 Hz
0.5 Gs
Vibration may be applied in the X, Y, or Z axis.
Operating normal translational random flat profile
10 - 500 Hz
0.5 GRMS
b. Operating—abnormal
Equipment as installed for normal operation shall not incur physical damage while subjected to periodic
vibration not exceeding:
15 minutes of duration at major resonant frequency
5-500 Hz @ 0.75 G (X, Y, or Z axis)
Vibration occurring at these levels may degrade operational performance during the abnormal vibration
period. Specified operational performance will continue when normal operating vibration levels are
resumed. This assumes system recovery routines are available.
Operating abnormal translational random flat profile
10 - 500 Hz
1.2 GRMS
c. Non-operating
The limits of non-operating vibration shall apply to all conditions of handling and transportation. This
includes both isolated drives and integrated drives.
The drive shall not incur physical damage or degraded performance as a result of continuous vibration not
exceeding
5 - 500 Hz @ 3 G (zero to peak)
Vibration may be applied in the X, Y, or Z axis.
Non-operating translational random flat profile
10 - 500 Hz
2.4 GRMS
7.5.5 Acoustics
Sound power during idle mode shall be 2.2 bels typical when measured to ISO 7779 specification.
There will not be any discrete tones more than 10 dB above the masking noise on typical drives when mea-
sured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the
masking noise on any drive.
7.5.6
Air cleanliness
The drive is designed to operate in a typical office environment with minimal environmental control.
7.5.7
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment.
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro-
sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil-
ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide,
36
Constellation.2 SAS Product Manual, Rev. H
chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-
nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
7.5.8
Electromagnetic susceptibility
Constellation.2 SAS Product Manual, Rev. H
37
8.0
About FIPS
The Federal Information Processing Standard (FIPS) Publication 140-2 is a U.S. Government Computer
Security Standard used to accredit cryptographic modules. It is titled 'Security Requirements for Cryptographic
Modules (FIPS PUB 140-2)' and is issued by the National Institute of Standards and Technology (NIST).
Purpose
This standard specifies the security requirements that will be satisfied by a cryptographic module utilized within
a security system protecting sensitive but unclassified information. The standard provides four increasing,
qualitative levels of security: Level 1, Level 2, Level 3 and Level 4. These levels are intended to cover the wide
range of potential applications and environments in which cryptographic modules may be employed.
Validation Program
Products that claim conformance to this standard are validated by the Cryptographic Module Validation Pro-
gram (CMVP) which is a joint effort between National Institute of Standards and Technology (NIST) and the
Communications Security Establishment (CSE) of the Government of Canada. Products validated as conform-
ing to FIPS 140-2 are accepted by the Federal agencies of both countries for the protection of sensitive infor-
mation (United States) or Designated Information (Canada).
In the CMVP, vendors of cryptographic modules use independent, accredited testing laborites to have their
modules tested. National Voluntary Laboratory Accreditation Program (NVLAP) accredited laboratories per-
form cryptographic module compliance/conformance testing.
Seagate Enterprise SED
by a NVLAP accredited lab to satisfy FIPS 140-2 Level 2 requirements. In order to operate in FIPS Approved
section in the 'Security Policy' document uploaded on the NIST website. To reference the product certification
visit - http://csrc.nist.gov/groups/STM/cmvp/documents/140-1/1401vend.htm, and search for “Seagate”.
Security Level 2
Security Level 2 enhances the physical security mechanisms of a Security Level 1 cryptographic module
by adding the requirement for tamper-evidence, which includes the use of tamper-evident coatings or
seals on removable covers of the module. Tamper-evident coatings or seals are placed on a cryptographic
module so that the coating or seal must be broken to attain physical access to the critical security
placed on covers to protect against unauthorized physical access. In addition Security Level 2 requires, at
a minimum, role-based authentication in which a cryptographic module authenticates the authorization of
an operator to assume a specific role and perform a corresponding set of services.
Constellation.2 SAS Product Manual, Rev. H
39
9.0
About self-encrypting drives
Self-encrypting drives (SEDs) offer encryption and security services for the protection of stored data, com-
monly known as “protection of data at rest.” These drives are compliant with the Trusted Computing Group
The Trusted Computing Group (TCG) is an organization sponsored and operated by companies in the com-
puter, storage and digital communications industry. Seagate’s SED models comply with the standards pub-
lished by the TCG.
To use the security features in the drive, the host must be capable of constructing and issuing the following two
SCSI commands:
• Security Protocol Out
• Security Protocol In
These commands are used to convey the TCG protocol to and from the drive in their command payloads.
9.1
Data encryption
Encrypting drives use one inline encryption engine for each port, employing AES-128 data encryption in Cipher
Block Chaining (CBC) mode to encrypt all data prior to being written on the media and to decrypt all data as it
is read from the media. The encryption engines are always in operation and cannot be disabled.
The 32-byte Data Encryption Key (DEK) is a random number which is generated by the drive, never leaves the
drive, and is inaccessible to the host system. The DEK is itself encrypted when it is stored on the media and
when it is in volatile temporary storage (DRAM) external to the encryption engine. A unique data encryption
9.2
Controlled access
The drive has two security providers (SPs) called the "Admin SP" and the "Locking SP." These act as gate-
keepers to the drive security services. Security-related commands will not be accepted unless they also supply
the correct credentials to prove the requester is authorized to perform the command.
9.2.1
Admin SP
Access to the Admin SP is available using the SID (Secure ID) password or the MSID (Manufacturers Secure
ID) password.
9.2.2
Locking SP
The Locking SP controls read/write access to the media and the cryptographic erase feature. Access to the
Locking SP is available using the BandMasterX or EraseMaster passwords. Since the drive owner can define
up to 16 data bands on the drive, each data band has its own password called BandMasterX where X is the
number of the data band (0 through 15).
Constellation.2 SAS Product Manual, Rev. H
41
9.2.3
Default password
When the drive is shipped from the factory, all passwords are set to the value of MSID. This 32-byte random
value can only be read by the host electronically over the interface. After receipt of the drive, it is the responsi-
bility of the owner to use the default MSID password as the authority to change all other passwords to unique
owner-specified values.
9.3
Random number generator (RNG)
The drive has a 32-byte hardware RNG that it is uses to derive encryption keys or, if requested to do so, to pro-
vide random numbers to the host for system use, including using these numbers as Authentication Keys (pass-
words) for the drive’s Admin and Locking SPs.
9.4
Drive locking
access controls for the individual bands.
The variable "LockOnReset" should be set to "PowerCycle" to ensure that the data bands will be locked if
power is lost. In addition "ReadLockEnabled" and "WriteLockEnabled" must be set to true in the locking table in
order for the bands "LockOnReset" setting of "PowerCycle" to actually lock access to the band when a "Power-
Cycle" event occurs. This scenario occurs if the drive is removed from its cabinet. The drive will not honor any
data read or write requests until the bands have been unlocked. This prevents the user data from being
accessed without the appropriate credentials when the drive has been removed from its cabinet and installed
in another system.
When the drive is shipped from the factory, the firmware download port is unlocked.
9.5
Data bands
When shipped from the factory, the drive is configured with a single data band called Band 0 (also known as
the Global Data Band) which comprises LBA 0 through LBA max. The host may allocate Band1 by specifying a
start LBA and an LBA range. The real estate for this band is taken from the Global Band. An additional 14 Data
Bands may be defined in a similar way (Band2 through Band15) but before these bands can be allocated LBA
space, they must first be individually enabled using the EraseMaster password.
Data bands cannot overlap but they can be sequential with one band ending at LBA (x) and the next beginning
at LBA (x+1).
Each data band has its own drive-generated encryption key and its own user-supplied password. The host may
4K LBA boundaries.
9.6
Cryptographic erase
A significant feature of SEDs is the ability to perform a cryptographic erase. This involves the host telling the
drive to change the data encryption key for a particular band. Once changed, the data is no longer recoverable
since it was written with one key and will be read using a different key. Since the drive overwrites the old key
with the new one, and keeps no history of key changes, the user data can never be recovered. This is tanta-
mount to an instantaneous data erase and is very useful if the drive is to be scrapped or redispositioned.
9.7
Authenticated firmware download
In addition to providing a locking mechanism to prevent unwanted firmware download attempts, the drive also
only accepts download files which have been cryptographically signed by the appropriate Seagate Design
Center.
42
Constellation.2 SAS Product Manual, Rev. H
Three conditions must be met before the drive will allow the download operation:
1. The download must be an SED file. A standard (base) drive (non-SED) file will be rejected.
2. The download file must be signed and authenticated.
3. As with a non-SED drive, the download file must pass the acceptance criteria for the drive. For example it
must be applicable to the correct drive model, and have compatible revision and customer status.
9.8
Power requirements
The standard drive models and the SED drive models have identical hardware, however the security and
encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a
small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in
requirements on the standard (non-SED) drive models.
9.9
Supported commands
The SED models support the following two commands in addition to the commands supported by the standard
(non-SED) models as listed in Table 7:
• Security Protocol Out (B5h)
• Security Protocol In (A2h)
Constellation.2 SAS Product Manual, Rev. H
43
10.0
Defect and error management
Seagate continues to use innovative technologies to manage defects and errors. These technologies are
designed to increase data integrity, perform drive self-maintenance, and validate proper drive operation.
SCSI defect and error management involves drive internal defect/error management and SAS system error
considerations (errors in communications between the initiator and the drive). In addition, Seagate provides
the following technologies used to increase data integrity and drive reliability:
The read error rates and specified storage capacities are not dependent on host (initiator) defect management
routines.
10.1
Drive internal defects/errors
During the initial drive format operation at the factory, media defects are identified, tagged as being unusable,
and their locations recorded on the drive primary defects list (referred to as the “P’ list and also as the ETF
defect list). At factory format time, these known defects are also reallocated, that is, reassigned to a new place
on the medium and the location listed in the defects reallocation table. The “P” list is not altered after factory
formatting. Locations of defects found and reallocated during error recovery procedures after drive shipment
are listed in the “G” list (defects growth list). The “P” and “G” lists may be referenced by the initiator using the
Read Defect Data command.
Details of the SCSI commands supported by the drive are described in the SAS Interface Manual. Also, more
information on the drive Error Recovery philosophy is presented in the SAS Interface Manual.
10.2
Drive error recovery procedures
When an error occurs during drive operation, the drive, if programmed to do so, performs error recovery proce-
dures to attempt to recover the data. The error recovery procedures used depend on the options previously set
in the Error Recovery Parameters mode page. Error recovery and defect management may involve using sev-
eral SCSI commands described in the SCSI Interface Manual. The drive implements selectable error recovery
time limits required in video applications.
The error recovery scheme supported by the drive provides a way to control the total error recovery time for the
entire command in addition to controlling the recovery level for a single LBA. The total amount of time spent in
error recovery for a command can be limited using the Recovery Time Limit bytes in the Error Recovery mode
page. The total amount of time spent in error recovery for a single LBA can be limited using the Read Retry
Count or Write Retry Count bytes in the Error Recovery mode page.
44
Constellation.2 SAS Product Manual, Rev. H
The drive firmware error recovery algorithms consist of 20 levels for read recoveries and five levels for write.
Each level may consist of multiple steps, where a step is defined as a recovery function involving a single re-
read or re-write attempt. The maximum level used by the drive in LBA recovery is determined by the read and
write retry counts.
Table 4 equates the read and write retry count with the maximum possible recovery time for read and write
recovery of individual LBAs. The times given do not include time taken to perform reallocations. Reallocations
are performed when the ARRE bit (for reads) or AWRE bit (for writes) is one, the RC bit is zero, and the recov-
ery time limit for the command has not yet been met. Time needed to perform reallocation is not counted
against the recovery time limit.
When the RC bit is one, reallocations are disabled even if the ARRE or AWRE bits are one. The drive will still
perform data recovery actions within the limits defined by the Read Retry Count, Write Retry Count, and
Recovery Time Limit parameters. However, the drive does not report any unrecovered errors.
Table 4:
Read and write retry count maximum recovery times
Maximum recovery time per
Maximum recovery time per
LBA (cumulative, msec)
Read retry count* LBA (cumulative, msec)
Write retry count
0
33.32
1
124.32
1
74.97
5
621.62
2
103.92
128.91
220.09
278.40
10
1243.23
1864.85
2486.47
3
15
4
20 (default)
5 (default)
* For read retry count, every tick ~ 5% of total error recovery. Valid range setting is 1-20.
e.g. 1 ~ 5%
5 ~ 25%
20 ~ 100%
Setting these retry counts to a value below the default setting could result in degradation of the unrecovered
error rate. For example, suppose the read/write recovery page has the RC bit = 0 and if the read retry count is
set to 5, this means ~ 25% of error recovery will be executed which consumes 621.62 ms (please refer to the
table above). If the limit is reached and a LBA has not yet been recovered (i.e. requires retries beyond 621.62
ms), the command will end with Check Condition status report and unrecoverable read error will be reported.
10.3
SAS system errors
Information on the reporting of operational errors or faults across the interface is given in the SAS Interface
Manual. The SSP Response returns information to the host about numerous kinds of errors or faults. The
Receive Diagnostic Results reports the results of diagnostic operations performed by the drive.
Status returned by the drive to the initiator is described in the SAS Interface Manual. Status reporting plays a
role in systems error management and its use in that respect is described in sections where the various com-
mands are discussed.
Constellation.2 SAS Product Manual, Rev. H
45
10.4
Background Media Scan
Background Media Scan (BMS) is a self-initiated media scan. BMS is defined in the T10 document SPC-4
available from the T10 committee. BMS performs sequential reads across the entire pack of the media while
the drive is idle. In RAID arrays, BMS allows hot spare drives to be scanned for defects prior to being put into
service by the host system. On regular duty drives, if the host system makes use of the BMS Log Page, it can
avoid placing data in suspect locations on the media. Unreadable and recovered error sites will be logged or
reallocated per ARRE/AWRE settings.
With BMS, the host system can consume less power and system overhead by only checking BMS status and
results rather than tying up the bus and consuming power in the process of host-initiated media scanning activ-
ity.
Since the background scan functions are only done during idle periods, BMS causes a negligible impact to sys-
tem performance. The first BMS scan for a newly manufactured drive is performed as quickly as possible to
verify the media and protect data by setting the “Start time after idle” to 5ms, all subsequent scans begin after
500ms of idle time. Other features that normally use idle time to function will function normally because BMS
functions for limited time bursts then suspends activity to allow other background functions to operate.
BMS interrupts immediately to service host commands from the interface bus while performing reads. BMS will
complete any BMS-initiated error recovery prior to returning to service host-initiated commands. Overhead
associated with a return to host-servicing activity from BMS only impacts the first command that interrupted
BMS, this results in a typical delay of about 1 ms.
10.5
Media Pre-Scan
Media Pre-Scan is a feature that allows the drive to repair media errors that would otherwise have been found
by the host system during critical data accesses early in the drive’s life. The default setting for Media Pre-Scan
is enabled on standard products. Media Pre-Scan checks each write command to determine if the destination
LBAs have been scanned by BMS. If the LBAs have been verified, the drive proceeds with the normal write
command. If the LBAs have not been verified by BMS, Pre-Scan will convert the write to a write verify to certify
that the data was properly written to the disk.
Note. During Pre-Scan write verify commands, write performance may decrease by 50% until Pre-Scan
completes. Write performance testing should be performed after Pre-Scan is complete. This may
be checked by reading the BMS status.
To expedite the scan of the full pack and subsequently exit from the Pre-Scan period, BMS will begin scanning
immediately when the drive goes to idle during the Pre-Scan period. In the event that the drive is in a high
transaction traffic environment and is unable to complete a BMS scan within 24 power on hours BMS will dis-
able Pre-Scan to restore full performance to the system.
10.6
Deferred Auto-Reallocation
Deferred Auto-Reallocation (DAR) simplifies reallocation algorithms at the system level by allowing the drive to
reallocate unreadable locations on a subsequent write command. Sites are marked for DAR during read oper-
ations performed by the drive. When a write command is received for an LBA marked for DAR, the auto-reallo-
cation process is invoked and attempts to rewrite the data to the original location. If a verification of this rewrite
fails, the sector is re-mapped to a spare location.
This is in contrast to the system having to use the Reassign Command to reassign a location that was unread-
able and then generate a write command to rewrite the data. DAR is most effective when AWRE and ARRE
are enabled—this is the default setting from the Seagate factory. With AWRE and ARRE disabled DAR is
unable to reallocate the failing location and will report an error sense code indicating that a write command is
being attempted to a previously failing location.
46
Constellation.2 SAS Product Manual, Rev. H
10.7
Idle Read After Write
Idle Read After Write (IRAW) utilizes idle time to verify the integrity of recently written data. During idle periods,
no active system requests, the drive reads recently written data from the media and compares it to valid write
command data resident in the drives data buffer. Any sectors that fail the comparison result in the invocation of
a rewrite and auto-reallocation process. The process attempts to rewrite the data to the original location. If a
verification of this rewrite fails, the sector is re-mapped to a spare location.
10.8
Protection Information (PI)
Protection Information is intended as a standardized approach to system level LRC traditionally provided by
systems using 520 byte formatted LBAs. Drives formatted with PI information provide the same, common LBA
count (i.e. same capacity point) as non-PI formatted drives. Sequential performance of a PI drive will be
reduced by approximately 1.56% due to the extra overhead of PI being transferred from the media that is not
calculated as part of the data transferred to the host. To determine the full transfer rate of a PI drive, transfers
should be calculated by adding the 8 extra bytes of PI to the transferred LBA length, i.e. 512 + 8 = 520. PI for-
matted drives are physically formatted to 520 byte sectors that store 512 bytes of customer data with 8 bytes of
Protection Information appended to it. The advantage of PI is that the Protection Information bits can be man-
aged at the HBA and HBA driver level. Allowing a system that typically does not support 520 LBA formats to
integrate this level of protection.
Protection Information is valid with any supported LBA size. 512 LBA size is used here as common example.
10.8.1
Levels of PI
There are 4 types of Protection Information.
Type 0 - Describes a drive that is not formatted with PI information bytes. This allows for legacy support in non-
PI systems.
Type 1 - Provides support of PI protection using 10 and 16 byte commands. The RDPROTECT and WRTPRO-
TECT bits allow for checking control through the CDB. Eight bytes of Protection Information are transmitted at
LBA boundaries across the interface if RDPROTECT and WRTPROTECT bits are nonzero values. Type 1
does not allow the use of 32 byte commands.
Type 2 - Provides checking control and additional expected fields within the 32 byte CDBs. Eight bytes of Pro-
tection Information are transmitted at LBA boundaries across the interface if RDPROTECT and WRTPRO-
TECT bits are nonzero values. Type 2 does allow the use of 10 and 16 byte commands with zero values in the
RDPROTECT and WRTPROTECT fields. The drive will generate 8 bytes (e.g.0xFFFF) 8 bytes of Protection
Information to be stored on the media, but the 8 bytes will not be transferred to the host during a read com-
mand.
Type 3 - Seagate products do not support Type 3.
10.8.2
Setting and determining the current Type Level
A drive is initialized to a type of PI by using the format command on a PI capable drive. Once a drive is format-
ted to a PI Type, it may be queried by a Read Capacity (16) command to report the PI type which it is currently
formatted to. PI Types cannot coexist on a single drive. A drive can only be formatted to a single PI Type. It can
be changed at anytime to a new Type but requires a low level format which destroys all existing data on the
drive. No other vehicle for changing the PI type is provided by the T10 SBC3 specification.
Type 1 PI format CDB command: 04 90 00 00 00 00, Write Buffer: 00 A0 00 00
Type 2 PI format CDB command: 04 D0 00 00 00 00, Write Buffer: 00 A0 00 00
Constellation.2 SAS Product Manual, Rev. H
47
10.8.3
Identifying a Protection Information drive
The Standard Inquiry provides a bit to indicate if PI is support by the drive. Vital Product Descriptor (VPD) page
0x86 provides bits to indicate the PI Types supported and which PI fields the drive supports checking.
Note. For further details with respect to PI, please refer to SCSI Block Commands - 3 (SBC-3) Draft Stan-
dard documentation.
48
Constellation.2 SAS Product Manual, Rev. H
11.0
Installation
Constellation.2 disk drive installation is a plug-and-play process. There are no jumpers, switches, or termina-
tors on the drive.
SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays
designed to accommodate the drive. In such systems, the host system typically provides a carrier or tray into
which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four
M3 x 0.5 metric screws. When tightening the screws, use a maximum torque of 4.5 in-lb +/- 0.45 in-lb. Do not
over-tighten or force the screws. You can mount the drive in any orientation.
Note. SAS drives are designed to be attached to the host system without I/O or power cables. If you
intend the use the drive in a non-backplane host system, connecting the drive using high-quality
cables is acceptable as long as the I/O cable length does not exceed 4 meters (13.1 feet).
Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host
system. This connects the drive directly to your system’s SAS connector. The SAS connector is normally
Power is supplied through the SAS connector.
The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the
drive only if you want to select a different logical block size.
Figure 11. Physical interface
11.1
Drive orientation
The drive may be mounted in any orientation. All drive performance characterizations, however, have been
done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two pre-
ferred mounting orientations.
Constellation.2 SAS Product Manual, Rev. H
49
11.2
Cooling
Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding
The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and
head and disk assembly (HDA). You should confirm that adequate heat removal is provided using the temper-
in which case the drive should be oriented, or air flow directed, so that the least amount of air flow resistance is
created while providing air flow to the electronics and HDA. Also, the shortest possible path between the air
inlet and exit should be chosen to minimize the travel length of air heated by the drive and other heat sources
within the rack, cabinet, or drawer environment.
terns are created by one or more fans, either forcing or drawing air as shown in the illustrations. Conduction,
convection, or other forced air-flow patterns are acceptable as long as the temperature measurement guide-
Figure 12. Air flow
Note. Image is for reference only, may not represent actual drive.
50
Constellation.2 SAS Product Manual, Rev. H
11.3
Drive mounting
Mount the drive using the bottom or side mounting holes. If you mount the drive using the bottom holes, ensure
that you do not physically distort the drive by attempting to mount it on a stiff, non-flat surface.
The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define
the allowable mounting surface stiffness:
K x X = F < 15lb = 67N
where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion
(units in inches or millimeters). The out-of-plane distortion (X) is determined by defining a plane with three of
the four mounting points fixed and evaluating the out-of-plane deflection of the fourth mounting point when a
known force (F) is applied to the fourth point.
11.4
Grounding
Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the
user. The equipment in which the drive is mounted is connected directly to the HDA and PCBA with no electri-
cally isolating shock mounts. If it is desired for the system chassis to not be connected to the HDA/PCBA
ground, the systems integrator or user must provide a nonconductive (electrically isolating) method of mount-
ing the drive in the host equipment.
Increased radiated emissions may result if you do not provide the maximum surface area ground connection
between system ground and drive ground. This is the system designer’s and integrator’s responsibility.
Constellation.2 SAS Product Manual, Rev. H
51
12.0
Interface requirements
This section partially describes the interface requirements as implemented on Constellation.2 drives. Addi-
tional information is provided in the SAS Interface Manual (part number 100293071).
12.1
SAS features
This section lists the SAS-specific features supported by Constellation.2 drives.
12.1.1
task management functions
Table 5:
SAS task management functions supported
Task name
Abort Task
Supported
Yes
Clear ACA
Yes
Clear task set
Abort task set
Yes
Yes
Logical Unit Reset
Query Task
Yes
Yes
12.1.2
task management responses
Table 6:
Task management response codes
Function name
Function complete
Invalid frame
Response code
00
02
04
05
08
09
Function not supported
Function failed
Function succeeded
Invalid logical unit
52
Constellation.2 SAS Product Manual, Rev. H
12.2
Dual port support
Constellation.2 SAS drives have two independent ports. These ports may be connected in the same or differ-
ent SCSI domains. Each drive port has a unique SAS address.
The two ports have the capability of independent port clocking (e.g. both ports can run at 6Gb/s or the first port
can run at 6Gb/s while the second port runs at 3Gb/s. The supported link rates are 1.5, 3.0, or 6.0Gb/s.
Subject to buffer availability, the Constellation.2 drives support:
• Concurrent port transfers—The drive supports receiving COMMAND, TASK management transfers on both
ports at the same time.
• Full duplex—The drive supports sending XFER_RDY, DATA and RESPONSE transfers while receiving
frames on both ports.
Constellation.2 SAS Product Manual, Rev. H
53
12.3
SCSI commands supported
Table 7 lists the SCSI commands supported by Constellation.2 drives.
Table 7: Supported commands
Command name
Command code
Supported
Change Definition
40h
39h
18h
3Ah
04h
N
Compare
N
N
N
Y
Y
N
Y
Y
Y
N
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
N
Y
Y
N
N
N
Y
Y
N
N
Y
Y
N
Copy
Copy and Verify
DCRT bit supported
DPRY bit supported
DSP bit supported
IMMED bit supported
IP bit supported
SI (Security Initialize) bit supported
STPF bit supported
VS (vendor specific)
Inquiry
12h
Date Code page (C1h)
Device Behavior page (C3h)
Firmware Numbers page (C0h)
Implemented Operating Def page (81h)
Jumper Settings page (C2h)
Supported Vital Product Data page (00h)
Unit Serial Number page (80h)
Lock-unlock cache
Log Select
36h
4Ch
PCR bit
DU bit
DS bit
TSD bit
ETC bit
TMC bit
LP bit
Protocol-specific Log Page for SAS (18h)
Log Sense
4Dh
Application Client Log page (0Fh)
Buffer Over-run/Under-run page (01h)
Cache Statistics page (37h)
Factory Log page (3Eh)
Information Exceptions Log page (2Fh)
54
Constellation.2 SAS Product Manual, Rev. H
Table 7:
Supported commands
Command name
Command code
Supported
Last n Deferred Errors or Asynchronous Events page (0Bh)
Last n Error Events page (07h)
Non-medium Error page (06h)
Pages Supported list (00h)
Read Error Counter page (03h)
Read Reverse Error Counter page (04h)
Self-test Results page (10h)
Start-stop Cycle Counter page (0Eh)
Temperature page (0Dh)
N
N
Y
Y
Y
N
Y
Y
Y
Verify Error Counter page (05h)
Write error counter page (02h)
Mode Select (same pages as Mode Sense 1Ah)
Mode Select (10) (same pages as Mode Sense 1Ah)
Mode Sense
Y
Y
15h
55h
1Ah
Y [2]
Y
Y [2]
Caching Parameters page (08h)
Control Mode page (0Ah)
Y
Y
Disconnect/Reconnect (02h)
Error Recovery page (01h)
Format page (03h)
Y
Y
Y
Information Exceptions Control page (1Ch)
Notch and Partition Page (0Ch)
Protocol-Specific Port page (19h)
Power Condition page (1Ah)
Rigid Disk Drive Geometry page (04h)
Unit Attention page (00h)
Y
N
Y
Y
Y
Y
Verify Error Recovery page (07h)
Xor Control page (10h)
Y
N
Mode Sense (10) (same pages as Mode Sense 1Ah)
Persistent Reserve In
5Ah
5Eh
5Fh
34h
08h
28h
Y
Y
Persistent Reserve Out
Y
Prefetch
N
Read (6)
Y
Read (10)
Y
DPO bit supported
Y
FUA bit supported
Y
Read (12)
A8h
N
Read (16)
88h
Y
Read (32)
7Fh/0009h
3Ch
N
Read Buffer (modes 0, 2, 3, Ah and Bh supported)
Read Capacity (10)
Y (non-SED drives only)
Y
25h
Constellation.2 SAS Product Manual, Rev. H
55
Table 7:
Supported commands
Command name
Command code
9Eh/10h
37h
Supported
Read Capacity (16)
Read Defect Data (10)
Read Defect Data (12)
Read Long
Y
Y
B7h
Y
3Eh
Y (non-SED drives only)
Read Long (16)
9Eh/11h
07h
Y
Reassign Blocks
Receive Diagnostic Results
Supported Diagnostics pages (00h)
Translate page (40h)
Release
Y
1Ch
Y
Y
Y
17h
57h
A0h
03h
Y
Release (10)
Y
Report LUNs
Y
Request Sense
Y
Actual Retry Count bytes
Extended Sense
Y
Y
Field Pointer bytes
Reserve
Y
16h
56h
Y
3rd Party Reserve
Extent Reservation
Reserve (10)
Y
N
Y
3rd Party Reserve
Extent Reservation
Rezero Unit
Y
N
01h
31h
30h
32h
A2h
B5h
0Bh
2Bh
1Dh
Y
Search Data Equal
Search Data High
Search Data Low
Security Protocol In
Security Protocol Out
Seek (6)
N
N
N
Y (SED models only)
Y (SED models only)
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Seek (10)
Send Diagnostics
Supported Diagnostics pages (00h)
Translate page (40h)
Set Limits
33h
1Bh
35h
91h
00h
2Fh
Start Unit/Stop Unit (spindle ceases rotating)
Synchronize Cache
Synchronize Cache (16)
Test Unit Ready
Verify (10)
BYTCHK bit
56
Constellation.2 SAS Product Manual, Rev. H
Table 7:
Supported commands
Command name
Command code
AFh
Supported
Verify (12)
N
Verify (16)
AFh
Y
Verify (32)
7Fh/000Ah
0Ah
N
Write (6)
Y
Write (10)
2Ah
Y
DPO bit
Y
FUA bit
Y
Write (12)
AAh
N
Write (16)
8Ah
Y
Write (32)
7Fh/000Bh
2Eh
N
Write and Verify (10)
Y
DPO bit
Y
Write and Verify (12)
AEh
N
Write and Verify (16)
8Eh
Y
Write and Verify (32)
7Fh/000Ch
3Bh
N
Write Buffer (modes 0, 2, supported)
Y (non-SED drives only)
Write Buffer
3Bh
Y (non-SED drives only)
Firmware Download option (modes 4, 5, 7)
Y (SED drives only)
Write Long (10)
Write Long (16)
PBdata
3Fh
Y
Y
Y
N
N
Y
N
N
N
N
9Fh/11h
41h
LBdata
Write Same (32)
XDRead
93h
7Fh/000Dh
52h
XDWrite
50h
XPWrite
51h
[1] Constellation.2 drives can format to 512, 520 or 528 bytes per logical block.
[2] Warning. Power loss during flash programming can result in firmware corruption. This usually makes the
drive inoperable.
[3] Reference Mode Sense command 1Ah for mode pages supported.
[4] Y = Yes. Command is supported.
N = No. Command is not supported.
A = Support is available on special request.
[5] Approximately 1.5 increase in time to complete this command for a SED drive versus a non-SED drive of
the same capacity.
Constellation.2 SAS Product Manual, Rev. H
57
12.3.1
Inquiry data
SAS Interface Manual.
Table 8:
Constellation.2 inquiry data
Data (hex)
Bytes
0-15
00
[53
R#
00
00
00
00
00
54
R#
00
00
00
43
xx** 12
8B
30
S#
00
00
00
79
53
74
00
30
S#
00
00
00
72
65
73
PP
36
S#
00
00
00
69
61
20
0A
32
S#
00
00
00
67
67
72
53
30
S#
00
00
00
68
61
65
45
53
S#
00
00
00
74
74
73
41
53]
S#
00
00
00
20
65
65
47
20
S#
00
00
00
28
20
72
41
20
00
00
00
00
63
41
76
54
20
00
00
00
00
29
6C
65
45
20
00
00
00
00
20
6C
64
20
20
00
00
00
00
Vendor ID
Product ID
16-31
39
R#
00
00
00
6F
35
R#
00
00
00
70
20
68
32-47
48-63
64-79
80-95
96-111
112-127
128-143
32* *Copyright
30* 30* 36*
72 69 67
20
20
notice
*
Copyright year (changes with actual year).
SCSI Revision support. See the appropriate SPC release documentation for definitions.
**
PP 10 = Inquiry data for an Inquiry command received on Port A.
30 = Inquiry data for an Inquiry command received on Port B.
R# Four ASCII digits representing the last four digits of the product firmware release number.
S# Eight ASCII digits representing the eight digits of the product serial number.
[ ]
Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST9500620SS.
Refer to the values below for the values of bytes 16 through 26 of your particular model:
ST9500621SS
ST9500622SS
ST91000640SS
ST91000641SS
ST91000642SS
53 54 39 35 30 30 36 32 31 53 53
53 54 39 35 30 30 36 32 32 53 53
53 54 39 31 30 30 30 36 34 30 53 53
53 54 39 31 30 30 30 36 34 31 53 53
53 54 39 31 30 30 30 36 34 32 53 53
12.3.2
Mode Sense data
The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The
drive maintains four sets of mode parameters:
1. Default values
Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the
drive’s PCB. These default values can be changed only by downloading a complete set of new firmware
into the flash E-PROM. An initiator can request and receive from the drive a list of default values and use
those in a Mode Select command to set up new current and saved values, where the values are change-
able.
2. Saved values
Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that
are allowed to be changed can be changed by this method. Parameters in the saved values list that are not
changeable by the Mode Select command get their values from default values storage.
58
Constellation.2 SAS Product Manual, Rev. H
When power is applied to the drive, it takes saved values from the media and stores them as current val-
ues in volatile memory. It is not possible to change the current values (or the saved values) with a Mode
Select command before the drive achieves operating speed and is “ready.” An attempt to do so results in a
“Check Condition” status.
On drives requiring unique saved values, the required unique saved values are stored into the saved val-
ues storage location on the media prior to shipping the drive. Some drives may have unique firmware with
unique default values also.
On standard OEM drives, the saved values are taken from the default values list and stored into the saved
values storage location on the media prior to shipping.
3. Current values
Current values are volatile values being used by the drive to control its operation. A Mode Select command
can be used to change the values identified as changeable values. Originally, current values are installed
from saved or default values after a power on reset, hard reset, or Bus Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which of the current values
and saved values can be changed by a Mode Select command. A one (1) indicates the value can be
changed. A zero (0) indicates the value is not changeable. For example, in Table 10, refer to Mode page
81, in the row entitled “CHG.” These are hex numbers representing the changeable values for Mode page
81. Note in columns 5 and 6 (bytes 04 and 05), there is 00h which indicates that in bytes 04 and 05 none of
the bits are changeable. Note also that bytes 06, 07, 09, 10, and 11 are not changeable, because those
fields are all zeros. In byte 02, hex value FF equates to the binary pattern 11111111. If there is a zero in any
bit position in the field, it means that bit is not changeable. Since all of the bits in byte 02 are ones, all of
these bits are changeable.
The changeable values list can only be changed by downloading new firmware into the flash E-PROM.
Note. Because there are often several different versions of drive control firmware in the total population of
drives in the field, the Mode Sense values given in the following tables may not exactly match those
of some drives.
The following tables list the values of the data bytes returned by the drive in response to the Mode Sense com-
mand pages for SCSI implementation (see the SAS Interface Manual).
DEF = Default value. Standard OEM drives are shipped configured this way.
CHG = Changeable bits; indicates if default value is changeable.
Constellation.2 SAS Product Manual, Rev. H
59
Table 9:
Mode Sense data changeable and default values for 1TB model drives
MODE DATA HEADER:
01 9a 00 10 01 00 00 10
BLOCK DESCRIPTOR:
00 00 00 00 74 70 6d b0 00 00 00 00 00 00 02 00
MODE PAGES:
DEF 81 0a c0 14 ff 00 00 00 05 00 ff ff
CHG 81 0a ff ff 00 00 00 00 ff 00 ff ff
DEF 82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00
CHG 82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00
DEF 83 16 bb d0 00 00 00 00 03 80 04 c4 02 00 00 01 00 ba 00 24 40 00 00 00
CHG 83 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 84 16 02 89 38 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1c 20 00 00
CHG 84 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 87 0a 00 14 ff 00 00 00 00 00 ff ff
CHG 87 0a 0f ff 00 00 00 00 00 00 ff ff
DEF 88 12 14 00 ff ff 00 00 ff ff ff ff 80 20 00 00 00 00 00 00
CHG 88 12 a5 00 00 00 ff ff ff ff 00 00 20 00 00 00 00 00 00 00
DEF 8a 0a 02 00 00 80 00 00 00 00 7f ff
CHG 8a 0a 07 f6 00 00 00 00 00 00 00 00
DEF 18 06 06 00 00 00 00 00
CHG 18 06 00 00 00 00 00 00
DEF 99 0e 06 00 07 d0 00 00 00 00 00 00 00 00 00 00
CHG 99 0e 50 00 ff ff ff ff ff ff 00 00 00 00 00 00
DEF 9a 26 01 07 00 00 00 0a 00 00 8c a0 00 00 17 70 00 00 46 50 00 00 46 50 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHG 9a 26 01 0f ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 9c 0a 10 00 00 00 00 00 00 00 00 01
CHG 9c 0a 9d 0f ff ff ff ff ff ff ff ff
DEF 80 06 00 80 0f 00 00 00
CHG 80 06 b7 c0 8f 00 00 00
60
Constellation.2 SAS Product Manual, Rev. H
Table 10: Mode Sense data changeable and default values for 500GB model drives
MODE DATA HEADER:
01 9a 00 10 01 00 00 10
BLOCK DESCRIPTOR:
00 00 00 00 3a 38 60 30 00 00 00 00 00 00 02 00
MODE PAGES:
DEF 81 0a c0 14 ff 00 00 00 05 00 ff ff
CHG 81 0a ff ff 00 00 00 00 ff 00 ff ff
DEF 82 0e 00 00 00 00 00 00 00 00 01 3a 00 00 00 00
CHG 82 0e 00 00 00 00 00 00 00 00 ff ff 00 00 00 00
DEF 83 16 bb d0 00 00 00 00 03 80 04 c4 02 00 00 01 00 a8 00 24 40 00 00 00
CHG 83 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 84 16 02 89 38 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1c 20 00 00
CHG 84 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 87 0a 00 14 ff 00 00 00 00 00 ff ff
CHG 87 0a 0f ff 00 00 00 00 00 00 ff ff
DEF 88 12 14 00 ff ff 00 00 ff ff ff ff 80 20 00 00 00 00 00 00
CHG 88 12 a5 00 00 00 ff ff ff ff 00 00 20 00 00 00 00 00 00 00
DEF 8a 0a 02 00 00 80 00 00 00 00 7f ff
CHG 8a 0a 07 f6 00 00 00 00 00 00 00 00
DEF 18 06 06 00 00 00 00 00
CHG 18 06 00 00 00 00 00 00
DEF 99 0e 06 00 07 d0 00 00 00 00 00 00 00 00 00 00
CHG 99 0e 50 00 ff ff ff ff ff ff 00 00 00 00 00 00
DEF 9a 26 01 07 00 00 00 0a 00 00 8c a0 00 00 17 70 00 00 46 50 00 00 46 50 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
CHG 9a 26 01 0f ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF 9c 0a 10 00 00 00 00 00 00 00 00 01
CHG 9c 0a 9d 0f ff ff ff ff ff ff ff ff
DEF 80 06 00 80 0f 00 00 00
CHG 80 06 b7 c0 8f 00 00 00
Constellation.2 SAS Product Manual, Rev. H
61
12.4
Miscellaneous operating features and conditions
supported. An “N” in the support column indicates the feature or condition is not supported.
Table 11: Miscellaneous features
Supported
Feature or condition
N
N
N
Y
N
Y
Y
Y
Y
N
Y
Automatic contingent allegiance
Asynchronous event notification
Synchronized (locked) spindle operation
Segmented caching
Zero latency read
Queue tagging (up to 128 queue tags supported)
Deferred error handling
Parameter rounding (controlled by Round bit in Mode Select page 0)
Reporting actual retry count in Extended Sense bytes 15, 16, and 17
Adaptive caching
SMP = 1 in Mode Select command needed to save RPL and rotational offset bytes
Table 12: Miscellaneous status
Supported
Status
Y
Y
Y
Y
Y
Y
Y
Y
N
N
Good
Check condition
Condition met/good
Busy
Intermediate/good
Intermediate/condition met/good
Reservation conflict
Task set full
ACA active
ACA active, faulted initiator
62
Constellation.2 SAS Product Manual, Rev. H
12.4.1
SAS physical interface
SAS connector.
Details of the physical, electrical, and logical characteristics are provided within this section. The operational
aspects of Seagate’s SAS drives are provided in the SAS Interface Manual.
Figure 13. Physical interface
Constellation.2 SAS Product Manual, Rev. H
63
0.80 (6X)
5.92
7.62
4.65
0.52 0.08 x 45
2.00 (3X)
0.45 0.03 (7X)
0.10 M E
5.08
42.73 REF.
41.13 0.15
0.20B
0.30 0.05 (2X)
C
A
B
1.10
4.00 0.08
0.15D
C OF DATUM D
L
R0.30 0.08 (4X)
A
0.30 0.05 (4X)
B
C
SEE Detail1
B
33.43 0.05
15.875
15.875
1.27 (14X)
1.27 (6X)
0.84 0.05 (22X)
5.08
0.15B
4.90 0.08
0.35MIN
P15
S1
P1
S7
C OF DATUM B
L
Figure 14. SAS device plug dimensions
64
Constellation.2 SAS Product Manual, Rev. H
Detail A
6.10
S14
S8
0.30 0.05 x 45 (5X)
2.25 0.05
0.40 0.05 X 45 (3X)
4.85 0.05
0.10B
CORING ALLOWED
IN THIS AREA.
E
4.40 0.15
R0.30 0.08
45
C
SEE Detail 2
1.95 0.08
A
0.35 0.05
SECTION C - C
3.90 0.15
SECTION A - A
CONTACT SURFACE FLUSH
TO DATUM A 0.03
0.08 0.05
65
1.90 0.08
1.23 0.05
0.08 0.05
30
Detail 2
2.40 0.08
0.10 A
SECTION B - B
D
Figure 15. SAS device plug dimensions (detail)
Constellation.2 SAS Product Manual, Rev. H
65
12.4.2
Physical characteristics
This section defines physical interface connector.
12.4.3
Connector requirements
Contact your preferred connector manufacturer for mating part information. Part numbers for SAS connectors
will be provided in a future revision of this publication when production parts are available from major connec-
tor manufacturers.
12.4.4
Electrical description
SAS drives use the device connector for:
• DC power
• SAS interface
• Activity LED
This connector is designed to either plug directly into a backpanel or accept cables.
12.4.5
Pin descriptions
This section provides a pin-out of the SAS device and a description of the functions provided by the pins.
Table 13: SAS pin descriptions
Pin
S1
Signal name
Port A Ground
+Port A_in
Signal type
Pin
P1*
P2*
P3
Signal name
NC (reserved 3.3Volts)
NC (reserved 3.3Volts)
NC (reserved 3.3Volts)
Ground
Signal type
S2*
S3*
S4
Diff. input pair
-Port A_in
Port A Ground
-Port A_out
+Port A_out
Port A Ground
Port B Ground
+Port B_in
P4
S5*
S6*
S7
Diff output pair
P5
Ground
P6
Ground
P7
5 Volts charge
5 Volts
S8
P8*
P9*
P10
P11*
P12
P13
P14*
P15*
S9*
S10*
S11
S12*
S13*
S14
Diff. input pair
Diff output pair
5 Volts
-Port B_in
Ground
Port A Ground
-Port B_out
+Port B_out
Port B Ground
Ready LED
Ground
Open collector out
12 Volts charge
12 Volts
12 Volts
* - Short pin to support hot plugging
NC - No connection in the drive.
66
Constellation.2 SAS Product Manual, Rev. H
12.4.6
SAS transmitters and receivers
pling to eliminate ground shift noise.
01
TX
T
X
l
T
T
M
100
100
01
Figure 16. SAS transmitters and receivers
12.4.7
Power
The drive receives power (+5 volts and +12 volts) through the SAS device connector.
Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power
supply is through the common ground pins. The supply current and return current must be distributed as
evenly as possible among the pins.
Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power sup-
ply is through the common ground pins. The supply current and return current must be distributed as evenly as
possible among the pins.
Current to the drive through the long power pins may be limited by the system to reduce inrush current to the
drive during hot plugging.
12.5
Signal characteristics
for signal type and signal name information.
12.5.1
Ready LED Out
Table 14: Ready LED Out conditions
Normal command activity
LED status
0
1
Ready LED Meaning bit mode page 19h
Spun down and no activity
Off
On
On
Off
Off
On
Off
On
Spun down and activity (command executing)
Spun up and no activity
Spun up and activity (command executing)
Spinning up or down
Blinks steadily
(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)
Format in progress, each cylinder change
Toggles on/off
Constellation.2 SAS Product Manual, Rev. H
67
The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the
proper +3.3 volt supply through an appropriate current limiting resistor. The LED and the current limiting resis-
tor are external to the drive. See Table 15 for the output characteristics of the LED drive signals.
Table 15: LED drive signal
State
Test condition
Output voltage
LED off, high
LED on, low
0 V ≤ VOH ≤ 3.6 V
-100 μA < I < 100 μA
OH
I
= 15 mA
0 ≤ VOL ≤ 0.225 V
OL
12.5.2
Differential signals
The drive SAS differential signals comply with the intra-enclosure (internal connector) requirements of the SAS
standard.
Table 16 defines the general interface characteristics.
Table 16: General interface characteristics
Characteristic
Units
Mbaud
ps
1.5Gb/s
1500
666.6
100
3.0Gb/s
3000
333.3
100
6.0Gb/s
6000
166.6
100
Bit rate (nominal)
Unit interval (UI)(nominal)
Impedance (nominal, differential )
Transmitter transients, maximum
Receiver transients, maximum
ohm
V
1.2
1.2
1.2
V
1.2
1.2
1.2
12.6
SAS-2 Specification Compliance
Seagate SAS-2 drives are entirely compatible with the latest SAS-2 Specification (T10/1760-D) Revision 16.
The most important characteristic of the SAS-2 drive at 6Gb/s is that the receiver is capable of adapting the
equalizer to optimize the receive margins. The SAS-2 drive has two types of equalizers:
1. A Decision Feedback Equalizer (DFE) which utilizes the standard SAS-2 training pattern transmitted dur-
ing the SNW-3 training gap. The DFE circuit can derive an optimal equalization characteristic to compen-
sate for many of the receive losses in the system.
2. A Feed Forward Equalizer (FFE) optimized to provide balanced receive margins over a range of channels
bounded by the best and worst case channels as defined by the relevant ANSI standard.
12.7
Additional information
Please contact your Seagate representative for SAS electrical details, if required.
For more information about the Phy, Link, Transport, and Applications layers of the SAS interface, refer to the
Seagate SAS Interface Manual, part number 100293071.
For more information about the SCSI commands used by Seagate SAS drives, refer to the Seagate SCSI
Commands Reference Manual, part number 100293068.
68
Constellation.2 SAS Product Manual, Rev. H
C
Index
capacity
Numerics
12 volt
pins 67
unformatted 11
CBC 41
condensation 33
connector
illustrated 66
requirements 66
cooling 50
CRC
A
acoustics 36
actuator 9
error 16
C-Tick 4
illustrated 50
altitude 34
ambient 33
ANSI documents
D
SCSI 6
DAR 46
auto write and read reallocation
programmable 8
data block size
data heads
read/write 11
data rate
internal 11
requirements 23
decrypt 41
defects 44
DEK 41
B
backpanel 66
BandMasterX 41
BMS 46
BSMI 4
buffer
data 8
space 13
Constellation.2 SAS Product Manual, Rev. H
69
description 7
DFE 68
G
gradient 33
grounding 51
dimensions 38
drive 36
H
heads
E
humidity 33
electrical
specifications 22
Electromagnetic compliance for the European Union
environment 50
I
Idle1 22
environmental
Idle2 22
limits 33
Idle3 22
requirements 15
EraseMaster 41
installation 49
guide 6
interface
error
management 44
rates 15
errors 44
errors 16
illustrated 63
physical 63
requirements 52
interleave
F
features 8
minimum 12
IRAW 47
interface 52
FFE 68
FIPS 39
firmware 8
corruption 57
J
function
jumpers 49
K
KCC 4
70
Constellation.2 SAS Product Manual, Rev. H
L
latency
temperature 33
LockOnReset 42
O
options 10
orientation 34
M
maintenance 15
P
packaged 35
passwords 41
miscellaneous feature support
PCBA 51
performance characteristics
detailed 11
general 12
miscellaneous status support
Busy 62
power 67
Good 62
dissipation 29
Intermediate/good 62
sequencing 26
PowerChoice 22
Mode sense
mounting 51
PowerCycle 42
holes 51
orientations 49
Q
N
noise
audible 3
Constellation.2 SAS Product Manual, Rev. H
71
shipping 21
shock 34
SID 41
R
receivers 67
reference
signal
characteristics 67
standards 3
Standby1 22
Standby2 22
surface stiffness
switches 49
synchronized spindle
operation 62
documents 6
reliability 9
specifications 15
resonance 34
RNG 42
RoHS 5
S
T
safety 3
SAS
interface 66
SCSI interface
seek error
TCG 41
limits 33
defined 16
rate 15
seek time
non-operating 33
regulation 3
See also cooling
terminators 49
transmitters 67
Self-Monitoring Analysis and Reporting Technology
shielding 3
72
Constellation.2 SAS Product Manual, Rev. H
74
Constellation.2 SAS Product Manual, Rev. H
Seagate Technology LLC
AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000
ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888
EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00
Publication Number: 100620418, Rev. H
April 2012
|