CP100
CP100
Com m ercial Series
Two-Way Radio User Guide
Talking and Receiving............... 15
Signal Strength Indicator/
Table of Contents
Product Safety and RF Exposure
Compliance...............................i
Introduction...................................1
FCC Licensing Information..........3
Getting Started..............................5
Installing the Swivel Belt
Channel Busy........................ 15
Talk Range............................... 15
Keypad Lock............................. 16
Hands-Free Use/VOX .............. 16
With Compatible VOX
Accessories........................... 16
Without Accessories................. 17
Setting VOX Sensitivity ............ 17
Monitoring a Channel ............... 18
Scanning (15 ch models only).. 18
Programming Features.............. 20
Entering Programming Mode ...20
Programming a Channel
Holster ....................................5
Installing the Nickel-Metal
Hydride Battery .......................6
Charging the CP100 Radio ........7
Turning Your Radio On or Off.....8
Adjusting the Volume..................8
Using the Radio ..........................8
Understanding the Display........10
Battery and Charging Options ..11
NiMH Battery.............................11
Alkaline Batteries ......................11
Charging with the Drop-in
(15 ch models only)............... 21
Programming the Frequency.... 21
Programming the Interference
Eliminator Code..................... 22
Assigning Channels to Presets
(15 Ch Models Only) ............. 22
Programming the Scramble
Feature.................................. 23
Programming Bandwidth (when
FCC allowable)...................... 23
Charging Tray (NNTN4019)...12
Reading the Battery Meter........13
Battery Life................................13
CP100 Factory Defaults .............14
1
Programming the Available Channel
(15 Ch Models Only)............. 24
Programming Call Tones ........ 24
Programming Microphone
Gain ...................................... 25
Editing the Scan List
(15 Ch Models Only)............. 26
Cloning..................................... 26
Advanced Features ................... 28
Troubleshooting ....................... 30
Use and Care.............................. 33
Frequencies and Bandwidths... 34
Verifying the SP21 Radio
Frequency and Code
Setting................................... 40
Motorola Limited Warranty....... 41
Software Copyright Notice ....... 47
Patent Notice ........................... 47
Export Law Assurances ........... 48
Replacement Parts .................... 49
2
Product Safety and RF Exposure Compliance
Before using this product, read the operating instructions for safe
usage contained in the Product Safety and RF Exposure booklet
enclosed with your radio.
!
C a u t i o n
ATTENTION!
This radio is restricted to occupational use only to satisfy FCC RF energy
exposure requirements. Before using this product, read the RF energy awareness
information and operating instructions in the Product Safety and RF Exposure
booklet enclosed with your radio (Motorola Publication part number 68P81095C98)
to ensure compliance with RF energy exposure limits.
For a list of Motorola-approved antennas, batteries, and other accessories, visit the
index.shtml.
i
Introduction
Thank you for purchasing a Motorola CP100 Radio. Your radio is a product of
Motorola’s 70 plus years of experience as a world leader in the designing and
manufacturing of communications equipment. The CP100 radios provide cost-
effective communications for businesses such as retail stores, restaurants, schools,
construction sites, manufacturing, property and hotel management and more.
Motorola two-way radios are the perfect communications solution for all of today’s
fast-paced industries.
Note: Please read this manual carefully to ensure you know how to properly
operate the radio before use.
Package Contents
•
•
•
•
•
•
•
•
Radio
Swivel Belt Holster
NiMH Battery
10-Hour Charger
User's Guide
Accessory Brochure
Warranty Card
Drop-In Charging Tray (not included with all models)
1
For a copy of a large-print version of this guide, or for product-related questions,
please contact:
1-800-927-2744 in the USA/Canada
1-888-390-6456 on your TTY (Text Telephone)
2
FCC Licensing Information
CP100 two-way radios operate on radio frequencies that are regulated by the
Federal Communications Commission (FCC). In order to transmit on these
frequencies, you are required to have a license issued by the FCC.
Application is made available on FCC Form 601 and Schedules D, H, and
Remittance Form 159.
To obtain these FCC forms please request document 000601 which includes all
forms and instructions. If you wish to have the document faxed, mailed or have
questions, please use the following contact information.
Mailed
call the FCC forms
hotline at:
Questions
regarding FCC license
contact the FCC at:
Faxed
contact the Fax-On-
Demand system at:
1-800-418-FORM
1-800-418-3676
1-888-CALL-FCC
1-888-225-5322
1-202-418-0177
Before filling out your application, you must decide which frequency(ies) you can
operate on. See Frequencies and Bandwidths.
For questions on determining your radio frequency, please call Motorola Product
Services at: 1-800-927-2744.
FCC
3
Changes or modifications not expressly approved by Motorola may void the user’s
authority granted by the FCC to operate this radio and should not be made. To
comply with FCC requirements, transmitter adjustments should be made only by or
under the supervision of a person certified as technically qualified to perform
transmitter maintenance and repairs in the private land mobile and fixed services as
certified by an organization representative of the user of those services.
Replacement of any transmitter component (crystal, semiconductor, etc.) not
authorized by the FCC equipment authorization for this radio could violate FCC
rules.
Note: Use of this radio outside the country where it was intended to be distributed
is subject to government regulations and may be prohibited.
FCC
4
Getting Started
This User’s Guide covers several CP100 models, and may detail some features your
radio does not have. Your model number is shown on the inside of the radio and can
been seen by removing the battery.
Installing the Swivel Belt Holster
1. Slide the bottom of radio into the holster until it snaps into
place.
2. To remove, push the tab above the battery door and pull the
radio from holster.
Note: In case of loss, please contact your point-of-sale or call
1-800-422-4210 to request replacement part number
CP100
NNTN4106.
NNTN4106 Swivel
Belt Holster
5
Installing the Nickel-Metal Hydride Battery
Your radio is powered by an NiMH
battery, which provides up to 15 hours*
of usage. Before you install the battery,
mark the date in the "INSTALL DATE"
section with a permanent marker. As in
vehicles, all rechargable batteries lose
capacity over time.
Ribbed
Latch
1. Push and hold down the ribbed
latch on the bottom of the radio
toward the contacts, then slide and
lift the battery door off.
2. With the Motorola logo side up, and
the charge contacts facing the
bottom of the radio, insert the top of
the battery into the radio.
1
3. Push the battery up and into the
2
battery compartment to fit tightly
into place.
4. Slide and snap the battery door into
place.
*Based upon 5% transmit/ 5% receive/
90% standby (standard duty cycle).
6
Charging the CP100 Radio
Charge the NiMH battery for 16 hours before using
it for the first time. It will only need up to eight hours
of charging thereafter.
Light
1. Make sure the radio is off.
2. Lift the accessory cover and plug the charger
(NNTN4077) into the lower jack.
3. Plug the charger into a power outlet. The light
on the charger glows during charging.
Note: For optimum battery life, do not charge the
battery for prolonged periods after it is fully
charged. Charging the battery over the
weekend is acceptable.
CP100
If the radio is on while charging, additional
time is required to charge the battery.
Use only the charger supplied with the
radio, or other CP100 power accessories.
See “Battery and Charging Options” on
page 11.
7
Turning Your Radio On or Off
Turn Pclockwise for On or counterclockwise for Off.
The radio chirps and the display briefly shows all features and display
segments of your CP100 radio.
k
188
218
Then the radio displays the current channel (larger number in the
center) and the frequency assigned to that channel (on right).
The interference eliminator code displays briefly. Then the current
channel remains displayed.
The transmit light on the front left of the radio flashes every three
seconds when the radio is on.
Frequency
Code
c
Adjusting the Volume
You can set the volume by turning P.
Note: Do not hold the radio too close to your ear when adjusting the
volume or if it is at a high setting.
Using the Radio
1. Press and hold Qto check for channel activity. If you hear static, the channel is
clear to use. Do not transmit if someone is speaking on the channel. Press Q
again to stop monitoring the channel.
2. Press and hold Mand speak into the microphone. To maximize clarity, hold the
radio two-to-three inches away from your mouth.
Note: The transmit light on the front left of the radio lights red when transmitting.
8
3. Release Mand listen for messages.
Basic Operation
Indicator Light
Use Pto:
Turn power on/off
Adjust radio volume
Use Bto:
Transmit call tone
Use Accessory Jack
for:
Radio plug-in charging
Audio accessories
Use Mto:
Talk
Exit a menu
CP100
Use Jto:
Use \to:
Lock the keypad
Scroll through available menus
Monitor the frequency
Turn scan on/off*
Use [and ]to:
Change channels*
Change menu settings
Use T/ Sto:
*Access presets
Microphone
Speaker
*
15 channel models only
9
Understanding the Display
Scan
(15-Ch. Models Only)
Keypad Lock
Scramble
Battery Meter
(2-Watt Models Only)
Signal Strength
Programming
Mode
Frequency and Interference
Eliminator Code
1
Frequency Indicator
VOX/Microphone Gain
Channel
10
Battery and Charging Options
You have several battery and charging options on your CP100 Two-Way Radio.
NiMH Battery
See “Installing the Nickel-Metal Hydride Battery” on page 6.
Alkaline Batteries
Your radio can also use 4 AA batteries; alkaline cells provide up to 24
hours* of radio use.
1. Push the ribbed latch on the bottom of the radio away from the
CP100
battery door.
2. Slide and lift the battery door off.
3. Place the AA batteries matching the markings in the compartment.
4. Slide and snap the battery door into place.
5. Press \until A or nflashes.
6. Press [or ]to select A for alkaline batteries, or nfor
rechargeable AA cells.
Note: This menu does not appear if the Motorola NiMH Battery is in
use.
*Please refer to the diagram and Battery Life on page 13.
A
11
Charging with the Drop-in Charging Tray
(NNTN4019)
(Not included with all models)
1. Place the drop-in charging tray on a flat
surface.
10-Hour charger
Drop-in
charging tray
2. Insert the plug of the 10-hour charger
into the jack of the drop-in charging tray.
3. Plug the charger into a power outlet.
Insert the battery or radio into the tray with
the Motorola logo or radio front facing the
front of the charger and the contacts facing
down.
Note: To extend battery life, do not
overcharge. Charging the battery
over the weekend is acceptable.
If the radio is on while charging, it
will take longer to fully charge.
Use only the charger supplied with the radio, or other CP100 radio power
accessories.
You can charge only one radio or battery at a time.
Tips: The radio can remain in the holster while charging.
12
Reading the Battery Meter
The battery meter located in the upper left corner of display indicates how much
battery power you have remaining.
Battery Type
3 Bars
2 Bars
1 Bar
Flashing
d
b
c
m
NiMH
100%-85%
85%-25%
75%-40%
25%-10%
40%-10%
Final 10%
Final 10%
AA Alkaline 100%-75%
Battery Life
Watts
NiMH
Alkaline
2
1
13 Hours
15 Hours
22 Hours
24 Hours
13
CP100 Factory Defaults
Your CP100 radio is programmed at the factory. If you need to change settings, refer
to Programming Features on page 20 and frequency list starting on page 34.
To restore your radio to factory default programming, turn the radio on while holding
the
and \for three seconds.
M
14
Talking and Receiving
Signal Strength Indicator/Channel Busy
The radio displays w when activity is on the frequency, and the
transmit light flashes at a faster rate of once per second.
6
When receiving, the display will show w and a signal strength from
1 (weakest) through 6 (strongest). This can help determine when a
radio is moving out of range.
1
Note: Obstacles that block the signal path may affect the strength of the incoming
signal.
Talk Range
Industrial
Multi-Level
Outdoor
Inside steel/concrete
industrial buildings
Inside multi-level
buildings
Flat ground with no
obstructions
Model
UHF 2W
UHF 1W
VHF 2W
VHF 1W
Up to 250,000 Sq. Ft.
Up to 200,000 Sq. Ft.
Up to 180,000 Sq. Ft.
Up to 150,000 Sq. Ft.
Up to 20 Floors
Up to 15 Floors
Up to 10 Floors
Up to 8 Floors
Up to 6 Miles
Up to 5 Miles
Up to 6 Miles
Up to 5 Miles
15
Keypad Lock
1. To maintain settings and lock keypad, press and hold \for three seconds.
2. To unlock, press and hold \for three seconds.
Hands-Free Use/VOX
Motorola CP100 radios can operate hands-free (VOX) when used with compatible
VOX accessories. A short delay occurs between when you start talking and the radio
transmits.
With Compatible VOX Accessories
1. Turn radio off.
2. Open accessory cover.
3. Insert plug of audio accessory firmly into accessory jack.
4. Turn radio on. Radio displays: g. If flashing and for
initial use, please refer to "Setting Vox Sensitivity" on
CP100
page 20.
5. Lower radio volume BEFORE placing accessory near ear.
6. To transmit, speak into accessory microphone and to
receive, stop talking.
7. You can disable VOX operation by pressing
removing the audio accessory.
or
M
Note: To order accessories, call 1 (800) 422-4210, or contact your point of
purchase.
16
Without Accessories
You can operate a CP100 15 channel radio hands-free without a VOX accessory.
1. Enable VOX by pressing Mwhile turning the radio on. gdisplays.
2. You can disable VOX operation temporarily by pressing
, gwill flash.
M
3. A short press of Mwill re-enable VOX.
4. To disable VOX, turn radio off then back on.
Setting
VOX Sensitivity
You can adjust the sensitivity of your radio’s accessory or microphone during VOX
operation (15 ch models only) to suit different operating environments. These menus
appear only if the VOX feature is in use, which is indicated by g.
1. Press
until gappears. The radio also displays which VOX sensitivity you are
\
setting:
H= External VOX (with audio accessory)
H
I = Internal VOX (without accessory; 15 ch models only)
2. Press
or
[ ]
to select the sensitivity level.
3
0= Off (VOX with accessories only, default settings)
1= Low sensitivity
2= Medium sensitivity
External VOX
3= High sensitivity
17
Monitoring a Channel
Check for channel activity.
1. Press and hold
. You will hear static if the channel is clear
Q
and w0will display.
2. Press
again to release.
Q
Scanning (15 ch models only)
You can scan up to 15 channels and frequencies. When the radio detects activity, it
stops scanning and locks in on the active channel. This allows you to talk and listen
to the person transmitting without changing channels.
1. To start scanning, briefly press
. Your radio displays hand begins to scroll
J
through channels. When the radio detects channel activity, it stops on that
channel and displays the signal strength indicator and the channel. You can talk
to the person(s) transmitting without having to switch channels by pressing
.
If
M
you press
while the radio is scanning, the radio transmits on the channel you
M
selected before you activated scan.
2. To stop scanning, briefly press
.
J
If no transmission occurs within five seconds, scanning resumes.
To scan a channel without interference eliminator codes, change the code for your set
channel to 0 before you press and release
.
J
Note: When you press
, you hear all traffic, but may not be able to transmit back
J
because the other person(s) may be using codes.
18
Scan Advancement / Nuisance Delete
Scan has several temporary features to make it easier to use.
Scan Advancement allows you to “skip” a busy channel to check for other activity.
•
Press ]to begin scanning again, but only temporarily.
Nuisance delete allows you to temporarily remove a channel from your scan list, it
will return the next time you use the scan feature.
•
Press and hold [to temporarily remove a channel from the scan list.
19
Programming Features
You can change the following features by entering the programming mode (k).
To talk with someone on your two-way radios, these settings must match:
•
•
•
•
•
Channel (15 ch models only)
Frequency
Interference Eliminator Code
Scramble code
Bandwidth (for optimal clarity)
You can also use kto set the following:
•
•
•
•
Call tones
Microphone Gain
Scan List (15 ch models only)
Available channels (15 ch models only)
Note: You cannot enter kwhile a VOX accessory is plugged into the radio.
Entering Programming Mode
You must enter Programming Mode to change your communication settings.
1. Press and hold
for three seconds while turning on your
M
J
radio. The radio beeps and displays k.
1
20
Programming a Channel (15 ch models only)
Each channel has its own Frequency, Interference Eliminator Code, Scramble Code,
and Bandwidth Settings.
Program each channel separately.
1. Select the channel that you will be programming.
2. The channel number flashes. land code displays
alternately.
6
3. Press [or ]to select the desired channel.
4. Press and hold Mto exit k, or press
to continue.
\
Programming the Frequency
Sets the frequency that your radio will use. As you are matching your
CP100 radio to existing SP21 radios, enter Programming Mode as
necessary, refer to page 20.
1. Press \to display l. The frequency flashes.
2. Press
or
[ ]
to select the desired frequency (See
“Frequencies and Bandwidths” beginning on page 34).
3. Press and hold Mto exit k, or press to continue.
\
21
Programming the Interference Eliminator Code
The Interference Eliminator Code helps minimize interference by
providing you with code combinations, which filter out static, noise,
and unwanted messages.
1. Enter Programming Mode as necessary, refer to “Entering
Programming Mode” on page 20.
Interference
Eliminator
Code
01075
2. Press \until the Interference Eliminator Code display number
begins to flash.
3. Press
or
to select the desired Code (See “Interference Eliminator Codes”
[ ]
beginning on page 37).
4. Press and hold Mto exit k, or press
to continue.
\
Assigning Channels to Presets (15 ch models only)
Presets allow you to easily switch to more frequently-used channels.
1. Enter Programming Mode as necessary, refer to “Entering Programming Mode”
on page 20.
2. Press
or
[ ]
to select the desired channel.
3. Press and hold Tor Sto assign that channel to a preset, radio beeps to
confirm. All of the channel settings are assigned to that preset button.
4. Press and hold Mto exit k, or press
to continue.
\
22
Programming the Scramble Feature
(2-watt models only)
The scramble feature garbles the transmission for anyone listening without
the same scramble setting. It does not guarantee confidentiality, but it increases
privacy. The scramble feature is set individually for each channel.
1. Enter Programming Mode as necessary, refer to “Entering Programming Mode”
on page 20.
2. Press \until edisplays.
3. Press
or
to select
1
,
2, or 3. Factory default is set to Off: 0.
[ ]
0
e
When you exit k, edisplays.
4. Press and hold Mto exit k.
Programming Bandwidth (when FCC allowable)
Some frequencies have selectable channel spacing, which must
match other radios for optimal radio quality. Bandwidth settings are
programmed for each channel.
1. Enter Programming Mode as necessary, refer to “Entering
Programming Mode” on page 20.
C
K
2. Press \until Kdisplays.
3. If D/Cflashes, press
or to select D(25.0 kHz) or C(12.5 kHz)
[ ]
bandwidth. (See “Frequencies and Bandwidths” beginning on page 37). If D/C
does not flash, then you cannot select the bandwidth for this frequency.
23
4. Press and hold Mto exit k.
Note: Spirit GT radios operate at 12.5 kHz. SP21 radios may operate at 25.0 kHz or
12.5 kHz bandwidth if selectable. If you have questions on radio use, call 1-
800-927-2744.
Programming the Available Channel (15 ch models only)
For applications requiring fewer channels, you can reduce the number of available
channels from 15. Older CP100 radios may not have this feature. Call 1-800-927-
2744 for more information.
1. Enter Programming Mode as necessary, refer to “Entering Programming Mode”
on page 20.
2. Press \until CH appears.
3. Press
or
[ ]
to select the number of channels you want available.
4. Press and hold Mto exit k.
Note: Programming settings for channels made unavailable are retained by the
radio.
Programming Call Tones
Your radio can transmit call tones to other radios in your group so
you can alert them that you are about to talk. The default is set to 0
(off) or you may choose 1, 2, or 3to choose a distinctive call tone.
1. Enter Programming Mode as necessary, refer to “Entering
Programming Mode” on page 20.
E
2. Press
until Edisplays.
\
24
3. Press
or
[ ]
to hear and select the call tone you want.
Note: The default is set to 0(off) or you may choose 1, 2, or 3to choose a
distinctive call tone.
4. Press and hold Mto exit k.
Once enabled, press
to transmit the call tone to others.
B
Programming Microphone Gain
The sensitivity of your radio’s microphone can be adjusted to suit different users or
operating environments.
1. Enter Programming Mode as necessary, refer to “Entering Programming Mode”
on page 23.
2. Press
3. Press
until gand ?(Gain) display.
[ ]
\
or
to select the sensitivity level.
?
3= High sensitivity, for quiet environments
2= Medium sensitivity, the default setting
1= Low sensitivity, for loud environments
4. Press and hold Mto exit k.
3
25
Editing the Scan List (15 ch models only)
To avoid hearing transmissions from unnecessary channels while scanning and to
decrease scan time, you can edit the scan list to skip unneeded channels.
1. Enter Programming Mode as necessary, refer to “Entering Programming Mode”
on page 20.
2. Press \until hdisplays and the channel and Yor nflashes.
3. Press [or ]to increase or decrease the channel.
4. Press
to display either:
J
Yto include the channel
nto exclude the channel
5. Press and hold Mto exit k.
Cloning
You can duplicate CP100 radio settings from one radio to another by using the
optional accessory NNTN4028 Multi-Unit Charger (MUC). Please refer to the MUC
User's Guide included with this accessory.
1. To enter the Programming Mode on the source radio, press and hold Qfor
M
three seconds while turning on your radio. The radio beeps and displays k.
2. Place the source radio in one of the front pockets of the MUC.
26
3. Turn on the target radio and place it directly behind the source
radio in the MUC.
4. Press and hold Qon the source radio. The source radio enters
Cloning Mode and transmits its settings to the target radio. Either
Wfor pass or Nfor fail appears on the source radio and the target
radio displays all icons if cloning was successful.
Source radio
Target radio
5. Turn the target radio off and back on again to use.
6. To clone additional radios, repeat steps 3 and 5.
7. Exit kon the source radio by holding down M.
Note: You can clone only one radio at a time.
k
188
218
The MUC does not need to be plugged in for Cloning feature to work.
Radios must be of the same band; UHF or VHF. Also, multi-channel models
can clone to single-channel radios, but only the first channel is cloned.
27
Advanced Features
You can set the following features by pressing and holding additional button(s) while
you turn on your radio.
Press this Key
While Turning
On the Radio
Default
Setting
To Do This
Turn Keypad Tones on/off
On
[
]
You can disable keypad beeps for silent menu
operation.
Turn End-of-Transmission Tone on/off
When enabled, your two-way radio transmits a tone
when you finish transmitting. It’s like saying “Roger”
or “Over.”
Note: If Keypad Tones are off, you will not hear the
end-of-transmission tone but it is
transmitted (if enabled).
Off
28
Press this Key
While Turning
On the Radio
Default
Setting
To Do This
Turn Battery Save on/off
Decreases attack time, which is the brief period of
time between when the radio receives a
transmission on its frequency and broadcasts
audio. Turning Battery Save off decreases battery
life by approximately 20%.
On
M Q [
Toggle Phase Shift
Changes your phase shift for optimal
communication with other Motorola radios.
180°
---
M B
180° CP100 (factory default),
Spirit M-Series, and Radius SP21
240° Spirit HP and Radius SP50
Restore Factory Defaults
Returns your radio to its original factory settings to
verify proper operation. Refer to page 14 for factory
default settings.
M \
29
Troubleshooting
Symptom
Try This:
Recharge or replace battery (NTN8971). Reposition or replace
alkaline batteries. For Nickel-Metal Hydride batteries, “Installing
the Nickel-Metal Hydride Battery” on page 6 or “Battery and
Charging Options” on page 11.
No Power
Make sure Mis completely pressed while transmitting.
Recharge, replace and/or reposition batteries.
Verify the transmit light is illuminated while speaking.
Message not
transmitted
Hearing other
noises or
conversation on
a channel
Frequency or Interference Eliminator Code may be in use,
change on all radios if possible. See “Programming the
Interference Eliminator Code” on page 22.
Scramble Code is On (2-watt models only), and/or setting does
not match other radios’ settings. See “Programming the
Scramble Feature” on page 23.
Poor Audio
Quality
Bandwidth of radios does not match. See “Programming
Bandwidth (when FCC allowable)” on page 23.
30
Symptom
Try This:
Steel and/or concrete structures, heavy foliage, buildings or
vehicles decrease range. Check for clear line of sight to improve
transmission. See “Talk Range” on page 15.
Limited talk
range
Wearing radio close to body such as in a pocket or on a belt
decreases range. Change location of radio.
Confirm radios have the same Channel, Frequency, Interference
Eliminator Code and Scramble Code settings, depending upon
model. See “Programming Features” on page 20.
Recharge, replace and/or reposition batteries.
Message not
received
Move to another location. Obstructions and operating indoors, or
in vehicles may decrease range.
Verify that the radio is not in Scan mode. See “Scanning (15 ch
models only)” on page 18.
Radios are too close, they must be at least five feet apart.
Radios are too far apart or obstacles are interfering with
transmission.
Heavy static or
interference
Keypad locked Unlock by holding \for three seconds.
31
Symptom
Try This:
Recharge or replace battery or batteries. Extreme operating
temperatures affect battery life. See “Battery Life” on page 13.
Low batteries
Reinsert radio/battery.
Charger light
does not come
on
Clean battery/charger contacts.
Verify that the charging pin is inserted correctly.
AA cells installed in radio, remove and replace with NiMH battery.
Low battery
meter reading
although new
batteries are
installed
Verify that the radio is set to the correct battery type (Single-cell
batteries only). See “Alkaline Batteries” on page 11.
Feature not set and on. See “Hands-Free Use/VOX” on page 16.
Cannot activate
VOX
Sensitivity set to 0. See “Setting VOX Sensitivity” on page 17.
Cannot enter
Unplug any audio accessories and retry.
k
mode
32
Use and Care
Use a soft damp cloth
to clean the exterior.
Do not immerse
in water.
Do not use alcohol or
cleaning solutions.
If the radio is submerged in water...
Turn radio off and
remove batteries.
Do not use radio until
completely dry.
Dry with soft cloth.
33
Frequencies and Bandwidths
The charts on the next few pages provide frequency information. These charts are
useful when using Motorola CP100 two-way radios with other business radios.
Frequency Display Number is identical to SP21 and Spirit GT frequency position
(where applicable).
VHF Frequencies
Display Frequency
Display Frequency
Number
(MHz)
Bandwidth
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
Number
16
(MHz)
Bandwidth
12.5/25.0
25.0
1
151.6250
151.9550
154.5700
154.6000
151.6550
151.6850
151.7150
151.7750
151.8050
151.8350
151.8950
151.9250
154.4900
154.5150
154.5400
158.4000
151.7000
151.7600
151.5125
151.8200
151.8800
151.9400
151.5125
151.7450
152.8650
152.7000
154.5275
2
3
4
5
6
7
8
9
17
18
19
*20
*21
*22
23
24
25
25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
25.0
25.0
25.0
25.0
25.0
10
11
12
13
14
15
26
27
*Note: Due to FCC regulations,
these frequencies transmit
at only 1 watt.
34
UHF Frequencies
Display
Display
Number
Frequency
(MHz)
Frequency
(MHz)
Bandwidth
Number
Bandwidth
1
2
464.5000
464.5500
467.7625
467.8125
467.8500
467.8750
467.9000
467.9250
462.5750
462.6250
462.6750
464.3250
464.8250
469.2625
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
12.5/25.0
15
16
17
18
19
20
21
22
23
24
25
26
27
28
469.5000
469.5500
462.7625
462.7875
462.8125
462.8375
462.8625
462.8875
462.9125
464.4875
461.0375
461.0625
461.0875
461.1125
12.5/25.0
12.5/25.0
12.5
3
4
12.5
5
12.5
6
12.5
7
12.5
8
12.5
9
12.5
10
11
12
13
14
12.5
12.5
12.5
12.5
12.5
35
UHF Frequencies (Continued)
Display
Number
Frequency
Display
Number
Frequency
(MHz)
(MHz)
Bandwidth
Bandwidth
29
30
31
32
33
34
35
36
37
38
39
40
41
42
461.1375
461.1625
461.1825
461.2125
461.2375
461.2625
461.2875
461.3125
461.3375
461.3625
462.7625
462.7875
462.8125
462.8375
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
43
44
45
46
47
48
49
50
51
52
53
54
55
56
462.8625
462.8875
462.9125
464.4875
464.5125
464.5375
464.5625
466.0375
466.0625
466.0875
466.1125
466.1375
466.1625
466.1875
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
36
Interference Eliminator Codes
Display Code
Display Code
Display Code
Number
(Hz)
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
Number
(Hz)
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
162.2
Number
(Hz)
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
1
2
14
27
15
28
3
16
29
4
17
30
5
18
31
6
19
32
7
20
33
8
21
34
9
22
35
10
11
12
13
23
36
24
37
25
38
26
Carrier Squelch (0) disables interference eliminator codes.
37
Digital Interference Eliminator Codes
Display
Number
Digital
Code
Display
Number
Digital
Code
Display
Number
Digital
Code
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
023
025
026
031
032
043
047
051
054
065
071
072
073
074
114
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
115
116
125
131
132
134
143
152
155
156
162
165
172
174
205
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
223
226
243
244
245
251
261
263
265
271
306
311
315
331
343
38
Digital Interference Eliminator Codes (Continued)
Display
Number
Digital
Code
Display
Number
Digital
Code
Display
Number
Digital
Code
84
85
86
87
88
89
90
91
92
93
94
95
96
346
351
364
365
371
411
412
413
423
431
432
445
464
97
465
466
503
506
516
532
546
565
606
612
624
627
631
110
111
112
113
114
115
116
117
118
119
120
121
632
654
662
664
703
712
723
731
732
734
743
754
98
99
100
101
102
103
104
105
106
107
108
109
39
Verifying the SP21 Frequency and Code Setting
The CP100 Two-Way radio replaces the SP21 radio. The factory default settings for
both radios are identical. However, existing radios may have been programmed to
different settings. To program your CP100 radio to talk with an SP21 radio, verify or
change your SP21 frequency and code settings as follows.
1. Press and hold
while you turn on the radio to enter programming mode.
M
The radio announces current frequency for that channel. For example: “frequency one.”
2. If desired, press to scroll through the frequencies.
M
The radio announces each frequency as you scroll. For example: “two...three...”
3. Release when you reach the desired frequency.
M
4. Press Qto select and save the frequency setting.
The radio announces current code setting. For example: “code two nine”
5. Press
to scroll through the codes.
M
The radio announces each code as you scroll. For example: “three zero...three one”
6. Release when you reach the desired code.
M
7. Press Qto select and save the code setting.
40
Motorola Limited Warranty
Personal Communications Products Purchased in the United States and
Canada
I. What this Warranty Covers
•
•
•
Products. Defects in materials and workmanship in wireless cellular telephones, pagers,
and/or two-way radios, and certain accessories that are sold with them, such as the
battery, battery charger and holster manufactured and/or sold by Motorola (Products).
Batteries. Defects in materials and workmanship in batteries that are manufactured by
Motorola and/or sold with Products are covered by this warranty only if the fully-charged
capacity falls below 80% of rated capacity or they leak.
Software. Physical defects in the media that tangibly embodies each copy of any software
supplied with the Products.
II. What the Period of Coverage Is
From the date the Products are purchased by the first end-user:
•
Products. The warranty is for one year. Exception: The warranty for Spirit GT series and
Talkabout series two-way radio accessories is for 90 days.
•
•
Software. The warranty is for 90 days.
Repairs / Replacements. The warranty is for the balance of the original warranty or for 90
days from the date you receive it, whichever is longer.
III. Who Is Covered
This warranty extends to the first end-user purchaser, only.
41
IV. What We Will Do to Correct Warranty Problems
At no charge to you, we have the option to repair or replace the Products or software
that do not conform to the warranty, or to refund the Products’ purchase price. We
may use functionally equivalent reconditioned/refurbished/pre-owned or new
Products or parts. No software updates are provided.
V. How to Get Warranty Service
Please call:
USA/Canada
Product Services 1-800-927-2744
Two-Way
TTY
1-800-353-2729
1-888-390-6456
(Text Telephone)
You will receive instructions on how to ship the Products to Motorola. You must ship
the Products to us with freight, duties and insurance prepaid. Along with the Products
you must include: (a) a copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of your service
provider (if this Product requires subscription service); (d) the name and location of
the installation facility (if applicable) and, most importantly; (e) your address and
telephone number. If requested, you must also return all detachable parts such as
antennas, batteries and chargers. RETAIN YOUR ORIGINAL PROOF OF
PURCHASE.
We will ship repaired or replacement Products at our expense for the freight and
insurance, but at your expense for any duties. If additional information is needed,
please contact us at the telephone number listed above.
42
VI. What this Warranty Does Not Cover
•
Products that are operated in combination with ancillary or peripheral equipment or
software not furnished by Motorola for use with the Products (“ancillary equipment”), or
any damage to the Products or ancillary equipment as a result of such use. Among other
things, “ancillary equipment” includes batteries, chargers, adaptors, and power supplies
not manufactured or supplied by Motorola. Any of these voids the warranty.
Someone other than Motorola (or its authorized service centers) tests, adjusts, installs,
maintains, alters, modifies or services the Products in any way. Any of these voids the
warranty.
Rechargeable batteries that: (a) are charged by other than the Motorola-approved battery
charger specified for charging such batteries; (b) have any broken seals or show evidence
of tampering; (c) are used in equipment other than the Product for which they are
specified; or (d) are charged and stored at temperatures greater than 60 degrees
centigrade. Any of these voids the warranty.
•
•
•
•
Products that have: (a) serial numbers or date tags that have been removed, altered or
obliterated; (b) board serial numbers that do not match each other, or board serial
numbers that do not match the housing; or (c) nonconforming or non-Motorola housings
or parts. Any of these voids the warranty.
Defects or damage that result from: (a) use of the Products in a manner that is not normal
or customary; (b) improper operation or misuse; (c) accident or neglect such as dropping
the Products onto hard surfaces; (d) contact with water, rain, extreme humidity or heavy
perspiration; (e) contact with sand, dirt or the like; or (f) contact with extreme heat, or spills
of food or liquid.
•
•
Physical damage to the surface of the Products, including scratches, cracks or other
damage to a display screen, lens or other externally exposed parts.
Failure of Products that is due primarily to any communication service or signal you may
subscribe to or use with the Products.
Coil cords that are stretched or that have any broken modular tabs.
Products that are leased.
•
•
43
Flat-rate repair rates may apply to Products not covered by this warranty. To obtain
information about Products needing repairs that are not covered by this warranty,
please call the telephone number previously listed. We will provide information on
repair availability, rates, methods of payment, where to send the Products, etc.
VII. Some Other Limitations
This is Motorola’s complete warranty for the Products, and states your exclusive
remedies. This warranty is given in lieu of all other express warranties. Implied
warranties, including without limitation, the implied warranties of merchantability and
fitness for a particular purpose, are given only if specifically required by applicable
law. Otherwise, they are specifically excluded.
No warranty is made as to coverage, availability, or grade of service provided by the
Products, whether through a service provider or otherwise.
No warranty is made that the software will meet your requirements or will work in
combination with any hardware or applications software products provided by third
parties, that the operation of the software products will be uninterrupted or error free,
or that all defects in the software products will be corrected.
In no event shall Motorola be liable, whether in contract or tort (including negligence)
for damages in excess of the purchase price of the Product, or for any indirect,
incidental, special or consequential damages of any kind, or loss of revenue or
profits, loss of business, loss of information or data, or other financial loss arising out
of or in connection with the ability or inability to use the Products, to the full extent
these damages may be disclaimed by law.
44
VIII. Patent and Software Provisions
At Motorola’s expense, we will defend you, and pay costs and damages that may be
finally awarded against you, to the extent that a lawsuit is based on a claim that the
Products directly infringe a United States patent. Our obligation is conditioned on: (a)
you notifying us promptly in writing when you receive notice of the claim; (b) you
giving us sole control of the defense of the suit and all negotiations for its settlement
or compromise; and (c) should the Products become, or in Motorola's opinion be
likely to become, the subject of a claim of infringement of a United States patent, you
permit us, at our option and expense, either to: procure for you the right to continue
using the Products; replace or modify them so that they become non-infringing; or
grant you a credit for such Products, as depreciated, and accept their return. The
depreciation will be an equal amount per year over the lifetime of the Products, as
established by Motorola.
Motorola will have no liability to you with respect to any claim of patent infringement
that is based upon the combination of the Products or parts furnished under this
limited warranty with ancillary equipment, as defined in VI., above.
This is Motorola’s entire liability with respect to infringement of patents by the
Products.
Laws in the United States and other countries preserve for Motorola and other third
party software providers certain exclusive rights for copyrighted software, such as the
exclusive rights to reproduce in copies and distribute copies of such software. The
software may be copied into, used in and redistributed with only those Products that
are associated with such software. No other use, including without limitation,
disassembly or reverse engineering of such software or exercise of exclusive rights
in such software is permitted.
45
IX. State Law and Other Jurisdiction Rights
Some states and other jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or limitation on the length of an implied
warranty, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights,
which vary from jurisdiction to jurisdiction.
To obtain information on Motorola Personal Communications Products, including
warranty service, accessories and optional Extended Warranties on selected
Products, please call:
Product Services 1-800-927-2744 All Products
1-800-461-4575
46
Software Copyright Notice
The Motorola products described in this manual may include copyrighted Motorola
and third party software stored in semiconductor memories or other media. Laws in
the United States and other countries preserve for Motorola and third party software
providers certain exclusive rights for copyrighted software, such as the exclusive
rights to distribute or reproduce the copyrighted software. Accordingly, any
copyrighted software contained in the Motorola products may not be modified,
reverse-engineered, distributed, or reproduced in any manner to the extent allowed
by law. Furthermore, the purchase of the Motorola products shall not be deemed to
grant either directly or by implication, estoppel, or otherwise, any license under the
copyrights, patents, or patent applications of Motorola or any third party software
provider, except for the normal, non-exclusive, royalty-free license to use that arises
by operation of law in the sale of a product.
Patent Notice
This product is covered by one or more of the following United States patents.
5896277 5894292 5864752 5699006 5742484 D408396 D399821 D387758
D389158 5894592 5893027 5789098 5734975 5861850 D395882 D383745
D389827 D389139 5929825 5926514 5953640 6071640 D413022 D416252
D416893 D433001
47
Export Law Assurances
This product is controlled under the export regulations of the United States of
America and Canada. The Governments of the United States of America and
Canada may restrict the exportation or re-exportation of this product to certain
destinations. For further information contact the U.S. Department of Commerce or
the Canadian Department of Foreign Affairs and International Trade.
Replacement of any transmitter component (crystal, semiconductor, etc.) not
authorized by the FCC equipment authorization for this radio could violate FCC rules.
More specifically, changes or modifications not expressly approved by Motorola may
void the user’s authority granted by the FCC to operate this radio and should not be
made. To comply with FCC requirements, transmitter adjustments should be made
only by or under the supervision of a person certified as technically qualified to
perform transmitter maintenance and repairs in the private land mobile and fixed
services as certified by an organization representative of the user of those services.
Replacement of any transmitter component (crystal, semiconductor, etc.) not
authorized by the FCC equipment authorization for this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be distributed
is subject to government regulations and may be prohibited
48
Replacement Parts
The following items can be purchased if necessary by contacting the Customer Care
and Services Division at 800-422-4210.
Part Number Description
NNTN4105
NNTN4106
3685739D01
6804112599
Battery Cover
Swivel Belt Holster
Volume Knob
CP100 User Guide
49
A
Plug-in..........................................7
Charging .............................................7
Cloning .............................................26
Code
Audio accessories ............................16
Adjust volume.................................8, 9
Advanced features ...........................28
Alkaline batteries ..............................11
Interference eliminator ...............22
D
B
Diagram
Bandwidth.........................................23
Basic operations.................................9
Battery
Function .......................................9
Drop-in charger.................................12
Alkaline.......................................11
Install ...................................11
Charge
Alkaline................................12
NiMH....................................12
Meter..........................................13
E
End-of-transmission tone..................28
External VOX..............................16, 32
F
FCC licensing information...................3
Frequency
C
Setting........................................21
Call display .......................................24
Channel
Functions ............................................9
H
Activity........................................18
Hands-free use ...........................16, 32
Charger
Drop-in .......................................12
Multi-unit.....................................26
50
I
O
Install
Obstacles .........................................15
Operating radio...................................9
Alkaline batteries .......................11
NiMH battery................................6
Interference eliminator code.............22
Internal VOX...............................16, 32
Introduction ........................................1
P
Plug
Audio..........................................16
Plug-in charger...................................7
Product-related questions ..................2
Product Safety..................................... i
Programming mode..........................20
K
Keypad tones ...................................28
L
Licensing information
R
Radio
FCC .............................................3
Clean .........................................33
Diagram .......................................9
Display.......................................13
Functions and settings.................9
Off................................................8
On................................................8
Operating.....................................9
Out of range.........................15, 31
Range
M
Meter
Battery .......................................10
Microphone gain.........................28, 25
Monitor signal strength...............10, 15
Talking .......................................15
Replacement Parts...........................49
51
RF Exposure........................................i
U
Use and care ....................................33
User guide
S
Safety information................................i
Scan .................................................18
Scan list............................................26
Sensitivity ...................................17, 25
Setting
Battery type................................11
Call tone.....................................24
Channel......................................21
Scramble code ...........................23
VOX sensitivity level.............17, 25
Signal strength indicator...................15
Large-print....................................2
V
VOX
External......................................16
Internal .......................................17
Sensitivity level...........................17
W
Warranty ..........................................41
Website
Accesories.....................................i
T
Talk range.........................................15
52
CP100 Programming Quick Reference
Function
Appearance
Qfor 3 sec. and turn on radio. k displays.
Press & hold
M
*Channel
Use
[or
]
for1 through 15.
2
Press
change, press
\
until l displays. To
or
Frequency
[
]
.
*depending upon model
*depending upon model
Interference
Eliminator
Code
Appears after l shows. Set
for each channel.
*Scramble
Code
Press \ until e displays. Must
e
be set to same code for all radios.
1
Press \ until K displays. Press
or
to select D (25.0 kHz)
[
]
or C (12.5 kHz).
Bandwidth
C
K
Note: If bandwidth is not flashing,
it is not selectable on the
chosen frequency.
CP100 Programming Quick Reference
Radio On
Visual
\as needed, then
[or
]
Press \ until CH displays.
*Available
Channels
Press
available channels.
or
to select number of
15 CH
[
]
Choose1, 2, 3, or
0 = Off (default).
Call Tone
E
Choose:
1 Low Sensitivity
2 Medium Sensitivity
3 High Sensitivity
Microphone
Gain
?
Press
or
to select channel,
[
]
*Scan List
then choose Y (yes) to include or
n (no) to exclude by pressing
Y
.
J
*depending upon model
• Extend Your Productivity
Provides a cost-effective solution
to onsite communication needs.
Designed for heavy duty,
everyday industrial use. Well
suited for construction,
manufacturing, security, property
management, retail, and more.
• Rugged MOTOROLA Quality
Shock/drop/temperature tested
to meet Motorola's high
standards.
• Weather/Dust Resistant
Designed to meet IP-54 rating
• Designed to meet Military
Specs
810 C, D, E & F
• Dependable Indoor/Outdoor
Coverage
• Simple and Easy to
Operate
• Business Exclusive
Frequencies
Allows one-to-one or group
communication at the push
of a button.
Frequencies set aside
exclusively for business-only
use. FCC License is required.
• 38 PL Codes, 83 Digital PL Codes
• Cost Efficient
No monthly fees to pay and • Hands-Free Mode (VOX)
no service contracts.
Compatible with Motorola
SP21 radios and audio
accessories.
Advanced voice activation (VOX)
lets you talk hands-free;
15-Channel models do not
require accessories.
• Voice Compression
Technology
• Cloning Capability
Helps provide better sound at
longer distances.
• 1-Year Limited Warranty
For details, please call:
1-800-927-2744
ecifica
Will provide a communication
range* of up to 250,000 sq. ft.
or 20 floors and up to 6 miles.
*Range will vary based on
terrain and conditions and
model selected.
Radio Specification Chart
Transmit Power
Receiver Sensitivity
Audio Output
Receiver Technology
NiMH Battery Life
tion Ch
2 Watts
-120 dBm for 12 dB SINAD
90 dB SPL
Direct Conversion
Approximately 13 hrs 2W
• Accessories for CP100 Radio
Brochure included - Convenient audio, power and charging accessories are available from your
point-of-sale
MOTOROLA, The Stylized M logo, and Radius are registered in the US Patent & Trademark Office. All other product or
service names are the property of their respective owners. © Motorola, Inc. 2002, 2003. All rights reserved. Printed in the
U.S.A.
Motorola CP100 Radio
WARNING CHOKING HAZARD
SMALL PARTS
Not for children under 3 years.
This product is not intended to be used
as a toy or plaything.
FCC
*6804112J99*
6804112J99-A
Proof of Purchase
License Required
|
