SIR-ALP10T
ALPINE COMPATIBLE
SIRIUS SATELLITE RADIO PLUS TRAFFIC TUNER
Installation Guide
Table of Contents
Package Contents ............................................................................................................... 3
Warnings and Cautions........................................................................................................ 4
Installation ............................................................................................................................ 6
Mounting the SIR-ALP10T Tuner .......................................................................................... 6
Installing theAntenna ........................................................................................................... 6
OptimumAntenna Mounting Locations ................................................................................. 7
Wiring and Cable Connections............................................................................................. 8
System Connection Examples ........................................................................................... 10
Activating Your SIRIUS Subscriptions ................................................................................. 15
Traffic Information Setup .................................................................................................... 17
Basic Operation ................................................................................................................. 19
Audio Headunit Messages .................................................................................................. 21
Navigation System Messages ............................................................................................ 21
Specifications .................................................................................................................... 22
12 Month Limited Warranty................................................................................................. 23
Package Contents
C
A
D
DATA
E
B
F
A
SIR-ALP10T Tuner
B
C
D
E
F
Magnetic MiniAntenna
Antenna Cable Cover/Tail
Alcohol Swab
G
H
Power Harness With In-Line Fuse
2.5-Meter Ai-NET Cable
3.5-Meter Data Cable
4 Mounting Screws
G
H
SIR-ALP10T InstallationGuide
3
WARNING
FCC Warning: This equipment may
generate or use radio frequency energy.
Changes or modifications to this equipment
may cause harmful interference unless the
modifications are expressly approved in this
User Guide. The user could lose the
authority to operate this equipment if an
unauthorized change or modification is
made.
This symbol means important
instructions. Failure to heed them can
result in serious injury or death.
DO NOT OPERATE ANY FUNCTION
THAT TAKES YOUR ATTENTION AWAY
FROM SAFELY DRIVING YOUR
VEHICLE.
Any function that requires your prolonged
attention should only be performed after
coming to a complete stop. Always stop the
vehicle in a safe location before performing
these functions. Failure to do so may result
in an accident.
Note: This equipment has been tested and
found to comply with Part 15 of the FCC
Rules. These rules are designed to provide
reasonable protection against harmful
interference. This equipment may cause
harmful interference to radio
communications if it is not installed and
used in accordance with these instructions.
However, there is no guarantee that
DO NOT OPEN, DISASSEMBLE OR
ALTER THE UNIT INANY WAY. Doing so
may result in fire, electric shock or product
damage.
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one of more of the following measures:
DO NOT INSERTANY OBJECTS INTO
THE UNIT. Doing so may result in fire,
electric shock or product damage.
USE THE CORRECTAMPERE RATING
WHEN REPLACING FUSE. Failure to do
so may result in fire, electric shock or
product damage.
• Relocate the receiving antenna.
MAKE THE CORRECT CONNECTIONS.
Failure to make proper connections may
result in fire or product damage.
• Consult the dealer or an experienced
technician for help.
DO NOT SPLICE INTOAELECTRICAL
CABLES. Never cut away cable insulation
to supply power to other equipment. Doing
so will exceed the current carrying capacity
of the wire and result in fire or electric
shock.
DO NOT INSTALL IN LOCATIONS THAT
MIGHT HINDER VEHICLE OPERATION.
Doing so may obstruct vision or hamper
movement which can result in a serious
accident.
DO NOT INSTALLTHE UNITTO HIGH
LEVELS OF HUMIDITY, MOISTURE OR
DUST. Doing so can result in electric shock
or product failure.
SIR-ALP10T Installation Guide
4
CAUTION
of the hole.
This symbol means important
instructions. Failure to heed them can
result in injury or material property
damage.
USE THE SPECIFIEDACCESSORY
PARTSAND INSTALLTHE PRODUCT
SECURELY. Be sure to use only the
specified accessory parts. Use of non-
specified parts may damage this unit
internally or may not securely install the unit
in place. This may cause parts to become
loose, resulting in hazards or product
failure.
HALT USE IMMEDIATELY IFAPROBLEM
APPEARS. Failure to do so may cause
personal injury or damage to the product.
Return the unit to your authorized retailer or
nearest service center for repairing.
INSTALLTHE WIRING SO THAT IT IS NOT
CRIMPED OR PINCHED BY SCREWS OR
SHARP METAL EDGES. Route the cables
away from moving parts or sharp pointed
edges. This will prevent crimping and
damage to the wiring. If the wiring must
pass through a metal hole, be sure to use a
rubber grommet to prevent the wire’s
USE CAUTION IF YOU NEED TO
DISCONNECT THE BATTERY TERMINAL.
Please consult the vehicle’s owner’s
manual or a service technician prior to
removing the battery positive or ground
connection, as it may cause damage to the
vehicle’s electrical system or require
reprogramming of the vehicle’s computer-
controlled devices.
insulation from being cut by the metal edge
SIR-ALP10T InstallationGuide
5
Installation
It is recommended that prior to starting the
installation, you read completely this
installation manual and follow the guidelines
listed below:
Installing the Antenna
The antenna includes a plastic cable cover/
tail which covers the exposed antenna
cable and keeps it attached securely to
vehicle roof. The tail also helps position the
antenna the proper distance from the rear
window, sunroof or rear hatch.
Consider the mounting location carefully.
You should make sure that you avoid the
following:
• Any location where the tuner is
exposed to moisture.
To attach the cover/tail:
1. Once you have determined the proper
mounting location (see the next
section), clean the area with the
supplied alcohol swab.
• Any location where the tuner is
exposed to extreme heat.
• Any location that would interfere with
moving parts on the vehicle or interfere
with driving.
2. Connect the antenna cover/tail to the
antenna cable, making sure that the
strain-relief on the antenna seats into
the cover/tail groove. Route the cable
through the wire channel in the cover/
tail.
Mounting the SIR-ALP10T Tuner
Be sure that you find a location that is flat
and has clearance above the tuner to
prevent any damage, as well as allow for
ventilation.
Antenna
(Underside)
Do not install the tuner under the carpet or
in a small enclosed area without proper
ventilation. Doing so can result in damage
to the tuner or the vehicle. Use the supplied
screws to securely fasten the unit.
Adhesive Strips
Cable
Cover/Tail
Antenna Cable
3. Remove the protective tape from the
adhesive and carefully position the
antenna with cover/tail and apply
pressure to secure it to the vehicle.
D
A
T
A
Antenna
Cable Cover/Tail
Caution:
If you are attaching the tuner directly to the
vehicle’s chassis, be sure that you check to
make sure the area behind the tuner is free
from moving parts, fuel or brake lines, wire
harnesses or any other items which may
get damaged by drilling a mounting hole or
from the screws.
Vehicle
SIR-ALP10T Installation Guide
6
Optimum Antenna Mounting Locations
The optimum location to mount the antenna
is on the roof of the vehicle. It is important to
avoid any obstruction that will block the
satellite signal, such as a roof rack. For
convertible vehicles, install the antenna on
the trunk lid as shown.
Sedan/Coupe
SUV/Mini-Van
• Place the antenna on a metal surface
of your vehicle at least 12" x 12", and at
least 6" from a window. (Use the
antenna cover/tail as a guide for the
proper distance from the rear window.)
• The antenna’s magnet will secure it to
the metal surface. The adhesive that is
attached to the antenna cover/tail will
secure the cable to the vehicle. Before
routing the antenna cable, confirm that
the antenna is mounted in a suitable
location.
Truck
Convertible (only)
• Route the cable from the antenna to the
vehicle’s interior by tucking it
underneath the rubber molding around
the rear window, if possible.
• Route the cable from the lowest point
of the rear window into the trunk. Take
advantage of any existing cable
channels or wiring conduits.
Caution:
• Do not pull the wire across sharp
edges that could damage it.
• For SUVs, minivans and five-door
vehicles, bring the cable into the
vehicle under the rubber molding of the
tailgate, and continue under the interior
trim.
• Keep the wire away from areas where it
could become tangled in the driver’s
and passenger’s feet.
• Keep the antenna wire away from
extreme heat, such as exhaust systems.
• From the trunk, carefully route the
cable to the location of the
• Avoid placing the cable near any
moving parts.
SIR-ALP10T and plug the SMB
connector into the tuner.
SIR-ALP10T InstallationGuide
7
Wiring and Cable Connections
Antenna Input
Connect the right-angle SMB connector
from the antenna. Push firmly to attach.
A
Ai-NET Output Connector
Use the supplied Ai-NET cable to connect
to theAlpine Headunit orAudio Processor –
See “System Connection Examples” for
more specific details.
Ai-NET Input Connector
Connect to optionalAlpine audio equipment
like CD Changers - See “System
Connection Examples” for more specific
details.
Power Harness Connector
After the wiring connections are complete,
plug the wiring harness into the connector.
Make sure to insert firmly to lock the
connector in place.
DATA
B
C
D
E
1
3
2
4
A
B
C
D
E
Antenna Input (SMB)
Ai-NET Output Connector (BLACK)
Ai-NET Input Connector (GRAY)
DATA Connector (BLACK)
Power Connector
1
ACC (Ignition Switched)
- Used in standalone navigation system
applications (no audio headunit)
2
Battery (+)
3 Ground (-)
4 No Connection
SIR-ALP10T Installation Guide
8
Right-angle
Antenna (21’ cable)
SMB Connector
Mount on Roof of Vehicle
Note: Connect the RED (ACC/IGN) wire
ONLY when using the SIR-ALP10T
without an Alpine headunit.
DATA
Ignition
Switch
Red (Pin 1) – ACC, Connect to
Ignition Switched Circuit
Yellow (Pin 2) – Connect to
Battery Positive (+)
Black (Pin 3) – Connect to Chassis
Ground (–)
3.5-meter Data Cable
(Connect to Alpine NVE-N872A)
2.5-meter Ai-NET Cable
(Connect to Alpine SAT Ready
Headunit or Signal Processor)
Note: It is important to follow the Input/Output configuration of the Ai-NET system. The
directionality is in reference to the Audio Path.
Gray Ai-NET connectors are Audio Input
Dark Blue Ai-NET Connectors are Audio Output. (Exception is the connector on an Alpine
Headunit – it can be either Input or Output depending on the position of the Ai-NET switch
on the bottom of the unit.
SIR-ALP10T InstallationGuide
9
System Connection Examples
System 1: Alpine Navigation System and SIR-ALP10T
DA
T
A
EX-2
DISPLAY
Alpine Monitor System
(TME-M770 or TME-M710)
(REAR VIEW)
Alpine Navigation System (NVE-N872A)
(FRONT VIEW)
Note: For this system configuration, be sure to connect the RED wire on the SIR-ALP10T to a
fused ACC or IGN line.
SIR-ALP10T Installation Guide
10
System 2: Alpine Headunit, Alpine Navigation System, and SIR-ALP10T
Alpine SAT Ready Headunit (Ai-NET CD Player or Mobile
Multimedia Station)
Special Note
Ai-NET
BOTTOM
COVER
DA
T
A
EQ
NORM
DIV
Ai-NET Switch Set to NORM~ Default Setting.
(FRONT VIEW)
(REAR VIEW)
Alpine Navigation System (NVE-N872A)
DISPLAY
EX-2
Alpine Monitor Headunit
Alpine Monitor System
(TME-M770 or TME-M710)
Note: For this system configuration, DO NOT connect the RED (ACC/IGN) line on the SIR-ALP10T.
SIR-ALP10T InstallationGuide
11
System Connection Examples (Continued)
System 3: Alpine Headunit, Alpine Navigation System,
CD Changer or IPOD Interface, and SIR-ALP10T
Alpine SAT Ready Headunit (Ai-NET CD Player or Mobile
Multimedia Station)
Special Note
Ai-NET
BOTTOM
COVER
DA
T
A
EQ
NORM
DIV
Ai-NET Switch Set to NORM~ Default Setting.
Alpine CD Changer (CHA-S634) / Alpine iPOD interface (KCA-420i)
Alpine Navigation System (NVE-N872A)
DISPLAY
(FRONT VIEW)
EX-2
(REAR VIEW)
Alpine Monitor Headunit
Alpine Monitor System
(TME-M770 or TME-M710)
Note: For this system configuration, DO NOT connect the RED (ACC/IGN) line on the SIR-ALP10T.
SIR-ALP10T Installation Guide
12
System 4: Alpine Multimedia Headunit, Alpine Navigation System,
CD-Changer or IPOD Interface, and SIR-ALP10T
DA
T
A
Alpine Multimedia Station Headunit
(IVA-D300, IVA-D310, IVA-D901)
Alpine CD Changer (CHA-S634)/Alpine iPOD interface (KCA-420i)
Hideway Headunit Tuner Module
Special Note
Bottom of
Alpine Navigation System (NVE-N872A)
(FRONT VIEW)
(REAR VIEW)
Tuner Module
Ai-NET
EQ
NORM
DIV
DISPLAY
EX-2
Ai-NET Switch Set to NORM ~ Defaut Setting
Note: For this system configuration, DO NOT connect the RED (ACC/IGN) line on the SIR-ALP10T.
SIR-ALP10T InstallationGuide
13
System Connection Examples (Continued)
System 5:Alpine Multimedia Headunit, Alpine Navigation System,
CD-Changer or IPOD Interface, Audio Processor, and SIR-ALP10T
DA
T
A
Alpine Multimedia Station Headunit (IVA-D300, IVA-D310, IVA-D901)
Special Note
Bottom of
Tuner Module
Headunit Input
Changer Input
Ai-NET
Hideway Headunit Tuner Module
EQ
NORM
DIV
Ai-NET Switch Set to EQ/DIV
Alpine Audio Processor
(PXA-H710, PXA-H700)
(FRONT VIEW)
(REAR VIEW)
Alpine Navigation System (NVE-N872A)
DISPLAY
EX-2
Alpine CD Changer (CHA-S634)/Alpine iPOD interface (KCA-420i)
Note: For this system configuration, DO NOT connect the RED (ACC/IGN) line on the SIR-ALP10T.
SIR-ALP10T Installation Guide
14
Activating Your SIRIUS Subscriptions
channel update is completed.
You must activate the SIR-ALP10T before
you can start to receive the SIRIUS Satellite
Radio service and the SIRIUS Traffic
service. Each is a separate service, and
each needs to be activated individually.
NOTE: Don’t push any buttons or
perform any operations until
updating has been completed. Once
updated, and the SIRIUS channels are
being received, the display will change
to Channel 184, the SIRIUS Satellite
Radio’s Preview Channel. At this time
you should also be able to hear the
audio from the Preview Channel.
In order to activate your radio and traffic
subscriptions, you will need the two SIRIUS
IDs (SIDs) – one for the SIRIUS Satellite
Radio service and one for the SIRIUS Traffic
service – which uniquely identify your SIR-
ALP10T tuner. The SIDs may be found on
sticker located on the bottom of the SIR-
ALP10T packaging or on the bottom of the
unit itself.
4. Use the UP/DN buttons to select
channel “255” on the display.
5. Once tuned to channel 255, the
headunit will display “SIRIUS” in the
Category Name Field, “RADIO ID” in the
Channel Field, and theAudio SID in the
Artist and Song fields of the display.
Note: You may have to press the TITLE
button on theAlpine headunit to show
the Audio SID. Be sure that the headunit
is set toAuto Scroll the text. If not, you
may only see the first eight characters
of the SID. (See yourAlpine headunit
owners manual for more information.)
The label will have printed on it two 12-digit
SID numbers. The first will be the Data SID
for the SIRIUS Traffic service, for example,
“Data SID: 123456789012”. The second is
theAudio SID for the SIRIUS Radio service,
for example, “Audio SID: 987654321098”.
Note: It is possible to activate only the
audio or the traffic service, just use the
appropriate SID. When you have located
both SIDs, write them down in the space
provided on page 22 of this manual.
6. Copy the Audio SID to the space
provided on page 22 of this manual.
Obtaining the Audio SID from the
Alpine Headunit
If you do not have access to the SID
stickers on the packaging or on the product,
you can obtain the Audio SID using the
following method.
Obtaining the Data SID from the
Alpine NVE-N872A Navigation
System
1. Turn on theAlpine navigation system
and monitor/display.
1. Make sure that the SIR-ALP10T is
properly connected, and that the
antenna is oriented to receive the
SIRIUS satellite signal.
2. The navigation system will display a
disclaimer notice. Select I ACCEPT to
proceed.
3. When the map screen is displayed,
2. Press and release the POWER/
SOURCE button on the audio headunit
to select SIRIUS as the source. (Each
press of the button will change to a
different audio source.)
touch the
right corner of the display screen.
menu icon in the upper
3. The display may read “UPDATING” or
“CALL 888-539-SIRIUS TO
SUBSCRIBE” until the SIR-ALP10T
SIR-ALP10T InstallationGuide
15
6. The next Setup screen will display the
Data SID near the bottom of the screen
where it says Sirius ID. Copy the Data
SID to the space provided on page 22
of this manual.
4. When the Nav Menu screen is
displayed, touch the Setup button, or
select it by tilting the joystick to highlight
it and press the ENTER button.
Activating the SIRIUS Audio and/or
Data Services
1. Be sure that yourAlpine headunit and
Navigation systems are turned on and
that you have the SID information
available.
2. Call SIRIUS toll-free at 1-888-539-
SIRIUS (1-888-539-7474) to activate
your subscriptions.
5. When the Setup screen is displayed,
touch the Traffic Information selection,
or select it by tilting the joystick to
highlight it and press the ENTER
button. Note: If the Traffic Information
selection is grayed out and cannot be
selected, this indicates that the SIR-
ALP10T is not connected, or connected
incorrectly. Check to be sure you have
correctly installed the SIR-ALP10T
according to the instructions in this
manual.
3. During the activation process, be sure
to tell the operator that have a receiver
on which you want to activate both a
SIRIUS Radio service subscription and
a SIRIUS Traffic service subscription.
Provide the operator with both theAudio
SID and the Data SID.
Once the subscription process is
completed, your audio and/or navigation
system is ready to use. Refer to the Alpine
headunit and/or navigation system owners
manuals for operation instructions.
If you have subscribed to the SIRIUS Traffic
service, proceed to the next section to
continue with the traffic information setup.
SIR-ALP10T Installation Guide
16
Traffic Information Setup
The traffic information setup controls the
way the traffic and navigation information is
displayed. To review and/or change these
parameters:
1. Turn on theAlpine navigation system
and monitor/display.
2. The navigation system will display a
disclaimer notice. Select I ACCEPT to
proceed.
6. The next Setup screen will display the
system status and the traffic setup
parameters.
3. When the map screen is displayed,
touch the
menu icon in the upper
right corner of the display screen.
The following sub-sections explain each of
the traffic information setup parameters.
4. When the Nav Menu screen is
displayed, touch the Setup button, or
select it by tilting the joystick to highlight
it and press the ENTER button.
System Status
System Status indicates the strength of the
SIRIUS data signal being received:
(Very Strong Signal)
(Strong Signal)
(Weak Signal)
(No Signal)
Traffic Icons
When the system receives traffic incident
information, you can choose whether to
display the traffic incident information as
icons on the map screen. Traffic incident
icons are displayed when the map scale is
set between 1/32 mile (50 m) and 5 miles
(10 km).
5. When the Setup screen is displayed,
touch the Traffic Information selection,
or select it by tilting the joystick to
highlight it and press the ENTER
button.
SIR-ALP10T InstallationGuide
17
it by tilting the joystick to highlight it and
press the ENTER button.
Selecting the Default button will choose to
display all traffic incident icons.
Traffic Speed Flow
When the system receives information
about traffic flow (congestion), you can
choose whether to display the traffic flow
information on the map screen.
To change the Traffic Icon setting, touch
Traffic Icons, or select it by tilting the
joystick to highlight your selection and press
the ENTER button.
Traffic flow information is displayed when
the map scale is set between 1/32 mile (50
m) and 5 miles (10 km).
Show: The selected traffic incident icons
are displayed on the map screen. If Show is
selected, you may also choose the types of
traffic incidents you want to be displayed.
Hide: No traffic incident icons are displayed
on the map screen.
To change the Traffic Speed Flow setting,
touch Traffic Speed Flow, or select it by
tilting the joystick to highlight your selection
and press the ENTER button.
Show: Traffic flow information is displayed
on the map screen.
If Show is selected, to change the types of
traffic incident icons which are displayed:
Hide: No traffic flow information is displayed
on the map screen.
1. Touch Edit, or select it by tilting the
joystick to highlight it and press the
ENTER button.
Traffic speed flow information is viewable on
the map only for those roads for which this
information is provided by the SIRIUS Traffic
service. Contact SIRIUS for updated
information on traffic flow coverage for your
area.
2. From the list, select (or de-select) the
types of traffic icons. Traffic incident
icon types with a checkmark next to
them will be displayed on the map.
Touch the icon type, or select (or de-
select) by tilting the joystick to highlight
the selection and press the ENTER
button.
Detour Based On
When you select Detour in the Traffic
Incident List screen, or press the Detour
button on the remote control, the system
will allow you to detour your route based
upon the setting you have chosen, traffic or
distance.
3. Selecting ALL will choose to display all
traffic incident icons.
4. When complete, touch Done, or select
SIR-ALP10T Installation Guide
18
Traffic: The system will provide a detour by
considering traffic congestion reported
along the route within 30 miles ahead of the
vehicle. This option should be chosen if you
plan to use the detour feature to avoid traffic
congestion.
Distance: the system will provide a detour
by considering the distance selected by the
user.
To change the Detour Based On setting,
touch Detour Based On, or select it by
tilting the joystick to highlight your selection
and press the ENTER button.
Basic Operation
2. When the Nav Menu screen is
displayed, touch the Information button,
or select it by tilting the joystick to
highlight it and press the ENTER
button.
The SIR-ALP10T SIRIUS Satellite Radio
Plus Traffic Tuner is compatible with most
Alpine satellite ready headunits from 2001
and up. The satellite traffic data is
compatible with the NVE-N872A Navigation
System. Consult theAlpine or SIRIUS
Customer Support Departments for more
information about compatibility.
Traffic Incident List
If you have subscribed to the SIRIUS traffic
service, you can display the Traffic Incident
List screen in order to confirm traffic
information enroute to a destination, or on
roads in the vicinity of the vehicle:
3. When the Info screen is displayed,
touch the Traffic Incident List selection,
or select it by tilting the joystick to
highlight it and press the ENTER
button.
1. When the map screen is displayed,
touch the
menu icon in the upper
right corner of the display screen.
SIR-ALP10T InstallationGuide
19
4. The Traffic Incident List screen is
displayed and provides a list of traffic
incident information in the vicinity of the
vehicle.
must be selected in the traffic setup for
this feature to work.
To begin calculating a detour, touch
Detour, or select it by tilting the joystick
to highlight it and press the ENTER
button. To not plan a detour, touch the
button, or select it by tilting the
joystick to highlight it and press the
ENTER button.
There are several options available to you
from this screen, which are described in the
following sections:
Traffic Incident
Touching a specific traffic incident from
the list (or selecting it by tilting the
joystick to highlight it and pressing the
ENTER button) will display details
about the traffic incident. Note that it is
possible for the detailed information to
be identical to the summary
Legend Button
Touching the Legend button, or tilting
the joystick to highlight the selection
and pressing the ENTER button,
displays a list of the icons associated
with each incident, and defines the
meaning of each icon.
information.
Crosshairs Icon
Icon
Legend
Accident
Touching the crosshairs icon next to a
traffic incident entry (or selecting it by
tilting the joystick to highlight it and
pressing the ENTER button) will display
a map of the area surrounding the
selected traffic incident.
Blockage
Construction / Roadworks
Danger
Detour Button
Touching the Detour button, or tilting the
joystick to highlight the selection and
pressing the ENTER button, will cause
the system to analyze the traffic data
within 30 miles of the vehicle’s position.
If traffic congestion is found, a message
is displayed informing you of the
distance to the congestion and the
anticipated delay if the congestion is not
detoured. Note that the Detour Based
on Traffic option (described previously)
Debris
Disabled Vehicle
Information
Sports Event
Traffic Jam
Weather
SIR-ALP10T Installation Guide
20
Viewing Traffic Speed and Flow Icon
Information
Icon
Speed
When you have set the system to display
traffic speed and flow icons on the map
display (discussed previously), the icons
are displayed in several shapes and colors
to indicate traffic speed.
Red Square
0-10 mph 0-20 km/h
Yellow Diamond 10-45 mph 20-90 km/h
Green Dot 45+ mph 90+ km/h
Traffic incident icons and detailed
information is available for all reported
incidents.
Audio Headunit Messages
These messages vary by headunit model. Consult yourAlpine headunit owners manual for
more information.
LOADING - Indicates that the SIR-ALP10T is acquiring audio and/or program information.
UPDATING or CALL 1-888-CALL SIRIUS TO ACTIVATE - This message appears when
the SIR-ALP10T is receiving a subscription update or during a channel or category update.
NO SIGNAL or NO SIGNAL or ACQUIRING - Will be displayed when there is a weak or
no antenna signal present.
ANTENNA or ANTENNA ERROR - Will be displayed if the antenna is damaged or
disconnected.
Navigation System Messages
CHECK ANTENNA - The antenna is not connected to the SIR-ALP10T. Check the antenna
cable to be sure it is securely attached to the unit.
UPDATING CHANNELS - This message appears when the SIR-ALP10T is receiving
channel mapping updates.
SIR-ALP10T InstallationGuide
21
Specifications
Operational Frequencies
Satellite .............................................................................2322.293/2330.207 MHz
Terrestrial .......................................................................................... 2326.250MHz
Power Requirements ......................................................................... 8-16 Volts DC
Fuse Type .......................................................................................... 1-AMP (ATC)
Chassis Size (without Mounting Tabs) ........................ 4-1/8” x 5” x 1-3/8” (WxHxD)
105mm x 126mm x 35mm (WxHxD)
Chassis Size (with Mounting Tabs) ............................. 4-7/8” x 5” x 1-3/8” (WxHxD)
127mm x 126mm x 35mm (WxHxD)
Antenna Type.................................................................................... Mini-Magnetic
Antenna Cable Length........................................................ 21’ (single micro-cable)
Connector Type ......................................................................... SMB (Right-angle)
Audio Interface ............................................... 2Ai-NET Connectors (Input/Output)
Audio Output .................................................................................... 850mV (Fixed)
Weight .................................................................................... 0.528 kg. (1.16 lbs.)
Included Cables ........................................................2.5 MeterAi-NET (Male/Male)
3.5 Meter Data Cable (Male/Male)
Note: Design and specifications are subject to change without notice.
Please write down your SIRIUS IDs in the space provided below:
SIRIUSRadio Service SID:
SIRIUS Traffic Service SID:
SIRIUS Customer Service: 1-888-539-7474
SIR-ALP10T Installation Guide
22
12 MONTH LIMITED WARRANTY
Sirius Satellite Radio warrants to the original retail purchaser of this product that should
this product or any part thereof, under normal use and conditions, be proven defective
in material or workmanship within 12 months from the date of original purchase, such
defect(s) will be repaired or replaced with new or reconditioned product (at the Company’s
option) without charge for parts and repair labor. To obtain repair or replacement within
the terms of this Warranty, the product is to be delivered with proof of warranty coverage
(e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the location
shown below under WARRANTY RETURN.
This Warranty does not extend to the elimination of externally generated static or noise,
to correction of antenna problems, to costs incurred for installation, removal or
reinstallation of the product, or to damage to tapes, compact discs, speakers,
accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the
Company, has suffered or been damaged through alteration, improper installation,
mishandling, misuse, neglect, accident, or by removal or defacement of the factory
serial number/bar code label(s). THE EXTENTOFTHE COMPANY’S LIABILITYUNDER
THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED
ABOVE AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE
PURCHASE PRICE PAID BYPURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY,
SHALLBELIMITEDTOTHEDURATIONOFTHISWRITTENWARRANTY. ANYACTION
FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED
WARRANTYOF MERCHANTABILITYMUSTBE BROUGHTWITHINAPERIOD OF 48
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE
COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER. No person or representative is authorized to assume for the Company
any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above limitations or
exclusions may not apply to you. This Warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
WARRANTY RETURN: To obtain repair or replacement within the terms of this Warranty, please
return product to an authorized Directed Electronics Dealer or call (800) 869-5590; proof of purchase
and description of defect are required. Products to be returned to an approved warranty station must
be shipped freight prepaid.
SIR-ALP10T Warranty card (Sept. 2005)
SIR-ALP10T InstallationGuide
23
SIRIUS Satellite Radio
1221 Avenue of the Americas
New York, NY 10020
(888) 539-7474
SIR-ALP10T Manual (101805a)
© 2005 SIRIUS Satellite Radio Inc.
® “SIRIUS” and the SIRIUS dog logo are registered trademarks of Sirius Satellite Radio Inc.
|