Preface
Congratulations on your choice of the Victor 1280-7 electronic calculator. Careful
design, quality materials, and advanced research and production facilities have given you
a calculator that with proper care will provide years of trouble-free service.
Table of Contents
Preparation
1 - 2
2
2
3
4
General Maintenance
How to Feed the Paper
Replacing the Ribbon
Keyboard Layout
Key and Slide Switch Features
Display Symbols
4 - 10
10
Reset Button
10
Using the Wireless Data Relay
Resetting the Wireless USB Connection
Specifications
11
12
13
Application Examples
Warranty
14 - 23
24
Preparation
BEFORE USING THE PRINTER FOR THE FIRST TIME:
Remove the tape holding the ink ribbon in place.
1. Remove the tape holding the printer cover in place.
2. Dispose of the tape.
3. Lift the printer cover up and then off.
4. Remove and dispose of the tape holding the ribbon in place.
(Fig. 1)
(Fig. 2)
Replacing the Ribbon
Your calculator is shipped with a 2-color ribbon already in place. You do not need to
install or change it before you begin using the calculator. When you have been using
your calculator for some time, however, the print will gradually become faint, indicating
that you should change the ribbon. To change the ribbon, follow these steps.
1.
Remove the paper roll, tearing the paper at the rear of the calculator. Use the
Paper Advance (↑) key to feed the remaining paper tape through the printer.
Then remove the printer cover.
2.
3.
Remove the old ribbon by pulling it upward. (Fig 6 shows the printer without
a ribbon.)
Install the ribbon spool with the black edge up. Victor recommends the Victor
7010 (Fig. 5).
4.
5.
Place the spool with the greater amount of ribbon on the left post.
Next unwind the ribbon as it is placed along the outside of the guides and in
front of the print wheel. (Fig. 7)
6.
Rotate the spools to take up any slack. Replace the printer cover and the
paper tape.
(Replace with the Victor #7010 Ink Ribbon)
(Fig. 5)
(Fig. 6)
(Fig. 7)
Keyboard Layout
This section describes the mode switches, data entry keys, and operating keys provided
on your calculator.
Key and Slide Switch Features
OFF ON
OFF The power is OFF.
ON The power is ON.
P NP PC
P
Print Mode: The printer is activated as long as the calculator is turned on.
NP
Non Print Mode: The printer is activated only when the paper feed key or the
non-add / date key (#/S) is pressed. This is also called the display only mode.
PC
PC Mode: In this mode the calculator will send the information entered to a
computer just as it would to the paper in a printer. The number entered will
appear in the first column and the operation performed will appear in the second
column. This is also called the Paperless Tape Mode.
• The Wireless Data Relay device must be installed into the computer’s USB
port when using any of the three PC Modes.
Wireless Data Relay (Fig. 9)
▲ 5/4 ▼
▲
Round Up Mode: The ▲ setting causes an answer to a calculation to
automatically round up.
5/4
Split Rounding Mode: This setting causes automatic round off. If the first digit
of the answer beyond the decimal setting is 0 to 4, the value is rounded down.
Otherwise the value is rounded up.
▼
Round Down Mode: Causes calculations to automatically round down.
(Truncate)
Σ • GT
Σ
Sigma Mode: When the slide switch is in the Sigma position, the results of
multiplication or division calculations completed by the = or % keys are
automatically added to the accumulator. The accumulated answer can be recalled
by pressing the T key.
•
The calculator is in neither Sigma mode nor Grand Total mode.
GT
Grand Total Mode: Any total created with the T key is automatically
accumulated to memory. The accumulated Grand Total can be recalled by
pressing the MT key.
A 0 2 3 F Kpad
A
Monetary Add Mode: In this setting, amounts entered are assumed to be
monetary. The calculator automatically supplies a decimal point to the left of the
last two digits entered.
0 2 3 Fixed Digit Mode: These settings specify the number of digits to the right of the
decimal point that are shown in the result.
F
Floating Decimal Point Mode: This setting specifies that all digits of the result
are shown, up to a maximum of 12. If the result exceeds these capacities, excess
digits to the right of the decimal point are dropped. No rounding takes place.
Kpad Keypad Mode: In this mode, the calculator acts as a keypad for the operator’s
computer. As numbers keys are pressed the entry is instantly sent to the
computer’s display. The T (Total) key acts as an Enter key and the Memory keys
act as Arrow keys to move cell to cell in a spreadsheet.
• The Wireless Data Relay device must be installed into the computer’s USB
port when using any of the three PC Modes.
Key Functions
0 – 9, 00, . Numeric Keys: The calculator uses the conventional 10 – key indexing
keyboard, and includes the double zero and decimal point keys. Whole numbers are
entered exactly as they are written.
Paper Feed Key: Used to advance the paper.
Right Shift Key: Used to delete the right most character of a live entry.
Percent Key: Completes percent calculations when Multiplication or Division
keys are used.
Division Key: The Division key performs division, automatic constant division,
and intermediate sequential operations. It establishes the next amount as a
constant divisor. Each divisor entry is retained as a constant until the X, ÷, or
Clear (C/CE) keys are depressed.
Equal Key: Press the equal key to get the result for a multiplication or division
equation.
Format Key: The Equals key is also used as the Format Key when programming
the Date. The operator may choose to change the way the date is displayed
(MM/DD/YYYY, DD/MM/YYYY, OR YYYY/ MM/DD) by pressing this key
while in the Date setting mode.
Multiplication Key: The Multiplication key performs multiplication, automatic
constant multiplication, and intermediate sequential operations. It establishes the
amount as a constant multiplicand.
AM/PM Key: The Multiplication key is also used in the Time setting mode to
switch from AM to PM or vice versa.
Time / Date Key: Used to display the Time or Date. Press once to see the Date
and press a 2nd time to see the Time. To change either the Date or the Time, press
the IC / SET key while displaying the Date or the Time.
Change Sign Key: Inverts the sign of the displayed number at key entry.
12 / 24 Key: The change sign key is also used to toggle between the 12
(AM/PM) or 24 hour clock mode.
IC Key: Prints the current Item count.
SET Key: Used to set the Date and Time. Press and hold until the Date starts to
flash on the display (Approximately 3 seconds). Enter the correct Date and press
the Set key again to set the Time.
Clear / Clear Entry Key: Clears a live entry by pressing the key once. Press
twice to clear the accumulator or pending calculation. The Clear key does not
clear the Memory. To clear the memory, press the MT key.
Minus Key: Subtracts an amount from the accumulator. To subtract the same
amount more than one time (repeat subtraction), enter that amount once and
depress the Minus key as many times as necessary. If this key is depressed
immediately after the (%) key, it works as a percent minus key.
Plus Key: Adds an amount to the accumulator. To add the same amount more
than one time (repeat addition), enter that amount once and depress the Plus key
as many times as necessary. If this key is depressed immediately after the (%)
key, it works as a percent add key.
Send To PC Key: This key is used to send the information in the calculator’s
display to the cursor of a personal computer. The information is sent exactly as it
is displayed on the calculator.
• The Wireless Data Relay device must be installed into the computer’s USB
port when using any of the three PC Modes.
Wireless Data Relay (Fig. 10)
Non Add Key: Will print a live entry as an identifier or as an invoice number
without adding the number to the accumulator. The number will appear on the
left hand side of the tape with the “#” sign.
Subtotal Key: Prints a subtotal, but does not clear the accumulator.
Total Key: Prints and clears the accumulator. This key will also print the total of
multiplication and division calculations when the slide switch is in the Sigma
mode (Σ).
Enter: When the calculator is in the Kpad mode, the T/Enter key acts as an Enter
key on a computer keyboard.
Memory + Key: Adds an amount to Memory. If there is a live calculation
pending, the Memory Plus key will complete the calculation and accumulate the
amount.
→ Key: Acts as an arrow key on a computer keyboard to move the cursor to the
right while the calculator is in the Kpad mode.
Memory – Key: Subtracts an amount from Memory. If there is a live calculation
pending, the Memory Minus key will complete the calculation and subtract the
amount from Memory.
← Key: Acts as an arrow key on a computer keyboard to move the cursor to the
left while the calculator is in the Kpad mode.
Memory Subtotal Key: Displays a subtotal of the memory contents. If the
calculator is in the Print mode, this subtotal will also print. Memory Subtotal
does not clear the contents of Memory.
↓ Key: Acts as an arrow key on a computer keyboard to move the cursor down
while the calculator is in the Kpad mode.
Memory Total Key: Prints and clears the total in Memory.
↑ Key: Acts as an arrow key on a computer keyboard to move the cursor up while
the calculator is in the Kpad mode.
Cost Sell Margin Keys
Cost, Sell, Margin keys are used for calculating cost, selling price, and profit
margin. Enter the value of any two variables to calculate the third. (Example:
Enter the cost of an item and press the Cost key. Next enter the selling price of an
item and press the Sell key. The Margin % will appear on the display and the
paper tape.)
Rate and Tax Keys
Tax 1 and Tax 2 keys are used to calculate an amount of tax using the preset tax
rate. Use the “+” key for calculating an amount including TAX, and the “-“ key
for calculating an amount excluding TAX.
To set TAX 1, press and hold the RATE key until the display flashes. Enter the
TAX Rate and then press TAX 1. TAX 1 is now set. To set TAX 2, follow the
same steps substituting TAX 2 for TAX 1.
Display Symbols
M
E
-
A number has stored into memory.
Error or over flow of capacity.
The displayed value is negative.
RESET Button
Electromagnetic interference or electrostatic discharge may cause the display to
malfunction or the contents of the Memory to be lost or altered. Should this occur, use
the tip of a ball point pen or a paper clip to press the RESET button at the back of the
calculator.
After resetting the calculator set the calendar, clock, and tax rate again.
Using the Wireless Data Relay Device
The Victor 1280-7 has three different modes of operation when connected via the USB
device.
1. SEND TO PC MODE – Press this key to send the contents of the display to
the connected PC.
Example: User needs the total of the calculation 100 + 200 + 300 sent to
the computer. Enter 100 + 200 + 300 T into the calculator. Next press the
SEND TO PC key and the answer (600) will be sent to the computer.
2. KPAD MODE – In this mode, the calculator acts as a keypad for the
operator’s computer. As number keys are pressed the entry is instantly sent to
the computer’s display. The T (Total) key acts as an Enter key and the
Memory keys act as Arrow keys to move cell to cell in a spreadsheet.
3. PC / PAPERLESS TAPE MODE – In this mode the calculator will send the
information entered to a computer just as it would to the paper in a printer.
The number entered will appear in the first column and the operation
performed will appear in the second column.
(Fig. 9)
• The Wireless Data Relay device must be installed when using any of the three
PC Modes.
Wireless Data Relay (Fig. 10)
*Note: The Victor 1280-7 Wireless Calculator will not work with Apple
computers.
Resetting the Wireless USB Connection
There may be a need to occasionally repair or reset the connection between the calculator
and the USB device. Symptoms that can cause the connection to be lost include periods
of non-use, interference from another device, or connecting the USB device to a different
computer. If the connection is lost, please follow these instructions to re-connect the
calculator to the USB device:
1. Start your computer and your spreadsheet program such as Microsoft Excel.
2. Push the power switch to “ON” on your calculator.
3. Push to the right-most slide switch to “Kpad” on your calculator.
4. Plug the Victor 1280-7 Wireless USB receiver into a USB port on the computer.
5. Wait until your computer recognizes the USB device. A pop-up box may appear
in the lower right corner of your display. This should take no more than 30
seconds.
6. Press the blue “RATE” key and hold for about 2 seconds. The calculator display
will show “--------------“ until the Wireless USB receiver is connected.
7. Once the connection is complete, the calculator display will show “– PC –“
8. Select a cell in your spreadsheet (position your cursor in the spreadsheet).
9. Test the connection by pressing the number “3” on your calculator and pressing
“ENTER” (the “T” key)
If the above steps do not result in a connection try this alternative method:
2. Press the blue “RATE” key and hold for about 2 seconds. The calculator display
will show “--------------“.
3. Plug the Victor 1280-7 Wireless USB receiver into a USB port on the computer.
4. Wait until your computer recognizes the USB device. A pop-up box may appear
in the lower right corner of your display. This should take no more than 30
seconds.
5. Once the connection is complete, the calculator display will show “– PC –“
6. Select a cell in your spreadsheet (position your cursor in the spreadsheet).
7. Test the connection by pressing the number “3” on your calculator and pressing
“ENTER” (the “T” key)
If the alternative method does not result in a connection, you may see “ERROR” on the
display. Turn the machine off and on again and repeat the above procedures. If a
connection is still not made, please call 1-800-628-2420 for assistance.
• The Wireless Data Relay device must be installed when using any of the three
PC Modes.
Wireless Data Relay (Fig. 8)
If your Wireless Data Relay is lost or damaged and a new Relay is purchased from
Victor, these steps will need to be completed the first time the Relay is used.
Specifications
Display
12 Digit, Fluorescent
Printing Speed
Printing Paper
4.6 Lines / Second
Width 2.25”, Diameter 3.15” Max
Width 57mm, Diamter 80mm Max
120V / 60 Hz (USA, CANADA)
0°C ~ 40°C (32°F ~ 104°F)
Power Sources
Ambient Temperature
Power Consumption
Dimension
120V / 0.16A / 19.2W
12.75” (L) X 8.75” (W) X 3.25 “ (H)
323 mm (L) X 220 mm (W) X 80 mm (H)
VICTOR 7010 (Twin Spool, C Wound Ribbon)
2 – Color (Negative numbers in red)
3.0 lbs. (1655 g)
Ink Ribbon
Printing Color
Weight
|