bicycle workstand
150 lb. capacity
Model 95365
asseMbly and operation instructions
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
to preVent serious injury, read and understand
all warnings and instructions before use.
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
for technical questions or replacement parts, please call 1-800-444-3353.
unpacking
When unpacking, check to make sure that the item is intact and undamaged. If any
parts are missing or broken (see parts list/assembly diagram), please call Harbor Freight
Tools at the number shown on the cover of this manual as soon as possible.
asseMbly instructions
note: For additional information regarding the parts listed in the following pages, refer to
the Assembly Diagram on page 6 of this manual.
The Bicycle Workstand can be easily assembled by taking the following steps. The Work-
stand will stand on its own and will hold up to 150 Lbs, evenly distributed.
1.
Set one Leg Assembly A (9) and Leg Assembly B (11) on each side of the Post (2)
so that the holes line up with the holes at the bottom of the Post (2). Through the
lowest hole, insert Screw (8) and thread on Nut (12)-see Figure 1. Through the next
hole up, insert the Screw (8) from the opposite direction and thread on Nut (12)-see
Assembly Diagram. Attach Leg Covers (10) to the end of each leg (not shown in
Figure 1).
Post (2)
Leg Cover (10)
Nut (12)
Screw (8)
Screw (8)
Nut (12)
Leg Assy A
(9)
Leg Assy B (11)
Figure 1
2.
Slide the Bottom Support Assembly Brace (7) down over the Post (2) until it is at
the adjustment holes. Set the Bottom Support Assembly Holder (4) and the Bottom
Support Assembly Brace (7) so that they line up on each side of the desired hole.
Thread the Handle Wheel (13) into the Bottom Support Assembly Brace (7). Slide
Washer (5) onto the threaded end of the Handle Wheel (13) and thread on Nut (6)
to secure it in place-see Figure 2.
SKU 95365
for technical questions, please call 1-800-444-3353.
Page 3
Bottom Support
Assembly Brace (7)
Bottom Support
Assembly Holder (4)
Nut (6)
Handle Wheel (13)
Washer (5)
Figure 2
3.
Attach the Top Support Assembly (15) to the top two holes on the Post (2). Secure
in place using two Screws (3)-see Figure 3.
Top Support
Assembly (15)
Screw (3)
Figure 3
operation instructions
1.
2.
Position the Workstandin a location where it will not be an obstruction to passersby.
Place it on a smooth, flat and level surface capable of supporting the Workstand
and the weight of the bicycle and components.
The Bottom Support Assembly Holder is adjustable. Set the Bottom Support As-
sembly Holder (4) to the desired height. With the bicycle upside down, set the top
tube (flat horizontal tube nearest the seat) of the bicycle onto the Bottom Support
Assembly Holder (4). Rest the bottom of the bicycle in the Top Support Assembly
(15).
inspection, Maintenance, and cleaning
1.
before eacH use, inspect the general condition of the tool. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts, and any
other condition that may affect its safe operation. do not use damaged equip-
ment.
SKU 95365
for technical questions, please call 1-800-444-3353.
Page 4
parts list
part
description
Q’ty part
description
Leg Assembly A
Leg Cover
Q’ty
1
2
3
4
5
6
7
Cover
Post
4
1
2
1
6
3
1
9
2
1
2
2
1
1
1
10
11
12
13
14
15
Screw
Leg Assembly B
Nut
Bottom Support Assy Holder
Washer
Handle Wheel
Nut
Nut
Bottom Support Assy Brace
Top Support
Assembly
please read tHe following carefully
THe MANUFACTUReR AND/OR DISTRIBUTOR HAS PROvIDeD THe PARTS LIST AND ASSeM-
BLY DIAgRAM IN THIS MANUAL AS A ReFeReNCe TOOL ONLY. NeITHeR THe MANUFACTUReR
OR DISTRIBUTOR MAKeS ANY RePReSeNTATION OR WARRANTY OF ANY KIND TO THe BUYeR
THAT He OR SHe IS qUALIFIeD TO MAKe ANY RePAIRS TO THe PRODUCT, OR THAT He OR
SHe IS qUALIFIeD TO RePLACe ANY PARTS OF THe PRODUCT. IN FACT, THe MANUFACTUReR
AND/OR DISTRIBUTOR eXPReSSLY STATeS THAT ALL RePAIRS AND PARTS RePLACeMeNTS
SHOULD Be UNDeRTAKeN BY CeRTIFIeD AND LICeNSeD TeCHNICIANS, AND NOT BY THe
BUYeR. THe BUYeR ASSUMeS ALL RISK AND LIABILITY ARISINg OUT OF HIS OR HeR RePAIRS
TO THe ORIgINAL PRODUCT OR RePLACeMeNT PARTS THeReTO, OR ARISINg OUT OF HIS
SKU 95365
for technical questions, please call 1-800-444-3353.
Page 5
asseMbly diagraM
SKU 95365
for technical questions, please call 1-800-444-3353.
Page 6
|