Dell Vostro 3267/3268
Owner's Manual
Regulatory Model: D13S
Regulatory Type: D13S002
Contents
1 Working on your computer.............................................................................................................................6
Turning off your computer — Windows 10..............................................................................................................7
2 Removing and installing components.............................................................................................................8
Recommended tools..........................................................................................................................................................8
Removing the cooling shroud.....................................................................................................................................9
Installing the expansion card......................................................................................................................................11
Hard drive...........................................................................................................................................................................11
Removing the hard drive assembly...........................................................................................................................11
Removing the hard drive from the hard drive bracket...........................................................................................11
WLAN card........................................................................................................................................................................15
Installing the WLAN card...........................................................................................................................................15
Heat sink............................................................................................................................................................................16
Removing the power supply unit (PSU)..................................................................................................................17
Contents
3
Coin cell battery...............................................................................................................................................................20
System board....................................................................................................................................................................21
Installing the system board.......................................................................................................................................23
3 Technology and components.......................................................................................................................26
Processors........................................................................................................................................................................26
Intel HD Graphics drivers..........................................................................................................................................30
Identifying the display adapter.................................................................................................................................30
Downloading drivers..................................................................................................................................................30
Adjusting brightness in Windows 10.........................................................................................................................31
Entering BIOS setup..................................................................................................................................................32
USB features....................................................................................................................................................................32
Compatibility...............................................................................................................................................................34
Verifying system memory ........................................................................................................................................35
4
Contents
5 System Setup overview...............................................................................................................................44
System Configuration screen options.....................................................................................................................45
Video screen options.................................................................................................................................................46
Performance screen options....................................................................................................................................49
Power Management screen options.......................................................................................................................50
Maintenance screen options.....................................................................................................................................51
System Log screen options......................................................................................................................................52
SupportAssist System Resolution screen options.................................................................................................52
ProcessorSystem informationMemoryVideoAudioCommunicationExpansion busDrivesCardsExternal
specifications....................................................................................................................................................................53
Contents
5
1
Working on your computer
Safety instructions
Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety.
Unless otherwise noted, each procedure included in this document assumes that the following conditions exist:
•
•
You have read the safety information that shipped with your computer.
A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse order.
WARNING: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface, such as a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its
edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a
cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Before working inside your computer
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
1
2
3
Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from
the network device.
4
5
6
7
Disconnect all network cables from the computer.
Disconnect your computer and all attached devices from their electrical outlets.
Press and hold the power button while the computer is unplugged to ground the system board.
Remove the cover.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface,
such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to
dissipate static electricity, which could harm internal components.
6
Working on your computer
Turning off your computer
Turning off your computer — Windows 10
CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.
1
Click or tap
Click or tap
.
2
and then click or tap Shut down.
NOTE: Ensure that the computer and all attached devices are turned off. If your computer and attached devices did
not automatically turn off when you shut down your operating system, press and hold the power button for about 6
seconds to turn them off.
After working inside your computer
After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your
computer.
1
Replace the cover.
CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer.
2
3
4
5
Connect any telephone or network cables to your computer.
Connect your computer and all attached devices to their electrical outlets.
Turn on your computer.
If required, verify that the computer works correctly by running Dell Diagnostics.
Working on your computer
7
2
Removing and installing components
This section provides detailed information on how to remove or install the components from your computer.
Recommended tools
The procedures in this document require the following tools:
•
•
•
•
Small flat blade screwdriver
Phillips # 1 screwdriver
Small plastic scribe
Hex screwdriver
Cover
Removing the cover
1
2
Follow the steps to remove the cover:
a
b
c
Remove the 6-32xL6.35 screws that secure the cover to the computer [1].
Slide the computer cover towards the back of the computer [2].
Lift and remove the cover from the computer [3].
Installing the cover
1
Slide the cover from the back of the computer, until the latches snap-in.
2
Tighten the 6-32xL6.35 screws to secure the cover.
8
Removing and installing components
3
Follow the procedures in After Working Inside Your Computer
Front Bezel
Removing the front bezel
1
2
3
Follow the steps to remove the front bezel:
a
Lift the tabs [1], and pull the front bezel [2].
b
Lift the front bezel to remove it from the computer [3].
Installing the front bezel
1
Hold the bezel and ensure that the hooks on the tabs snap into the notches on the computer.
Rotate the front bezel toward the front of the computer.
Press the front bezel until the tabs snap in.
2
3
4
5
Cooling shroud
Removing the cooling shroud
NOTE: Cooling shroud is not a mandatory removal but recommended for easier access to the cables.
1
Remove the cover
2
3
Follow the steps to remove the heat sink fan cover:
a
b
Pry the plastic notches that secure the fan cover in an outward direction [1].
Remove the fan cover from the heat sink assembly [2].
Removing and installing components
9
Installing the cooling shroud
1
Align the tabs on the cooling shroud with the securing slots on the computer.
Lower the cooling shroud into the chassis until it is firmly seated.
2
3
4
Expansion card
Removing the expansion card
1
2
3
Perform the following steps to remove the expansion card:
a
Pull the metal tab to release the expansion card [1].
b
Push the tab forward [2], and remove the expansion card from the slot on the computer [3].
10
Removing and installing components
Installing the expansion card
1
Insert the expansion card on the slot.
2
3
4
5
Push the card- retention latch to secure the expansion card.
Push the metal tab until it snaps in place.
Install the cover
Hard drive
Removing the hard drive assembly
1
2
Remove the:
a
b
c
3
4
Disconnect the power and the data cables from the hard drive.
NOTE: For easy access to the power and the data cables, it is recommended to remove the cooling shroud.
Follow the steps to remove the hard drive assembly:
a
b
Remove the 6-32xL3.6 screws that secure the hard drive to the drive bay.
Press the blue tab, and slide the hard drive from the hard drive bay.
Removing the hard drive from the hard drive bracket
1
2
Remove:
a
b
c
Removing and installing components
11
d
3
Follow the steps to remove hard drive bracket:
a
b
Remove the screw that secures the hard drive to the bracket.
Slide and remove the hard drive from the bracket.
Installing the hard drive into the hard drive bracket
1
Slide the hard drive and tighten the screws to secure the hard drive to the bracket.
2
Install:
a
b
c
d
3
Installing the hard drive assembly
1
Slide the hard drive assembly into the drive bay.
Tighten the 6-32xL3.6 screws to secure the hard-drive assembly to the computer.
Connect the data and power cables to the hard drive.
Install:
2
3
4
a
b
c
5
Optical drive
Removing the optical drive
1
2
Remove the:
a
b
c
d
3
Follow the steps to release the optical drive:
a
b
c
Remove the 6-32xL3.6 screw that secures the optical drive to the drive bay [1].
Press the blue tab to loosen the optical drive [2].
Slide the optical drive bracket from the computer [3].
12
Removing and installing components
4
Follow the steps to remove the optical drive:
a
Disconnect the power and the data cables from the optical drive [1].
NOTE: For easy access to the power and the data cables, it is recommended to remove the cooling shroud.
b
Slide the optical drive [2] and lift it up to remove it from the chassis [3].
Removing the optical drive bracket
1
2
Remove the:
a
b
c
d
e
3
Follow the steps to remove the bracket from the optical drive.
Remove the M2L2(04) screws that secure the bracket to the optical drive.
a
Removing and installing components
13
b
Slide the optical drive from the bracket.
NOTE: Remove the optical-drive bracket only if you are replacing with a new optical drive. Otherwise, if optical drive
removal is only a pre-requisite to remove other components, then ignore Step 5 and Step 6
Installing the optical drive bracket
1
Slide the optical drive into the drive bay until it snaps.
Tighten the M2L2(04) screw to secure the optical drive to the bracket.
Install the:
2
3
a
b
c
d
e
4
Installing the optical drive
1
Insert the optical drive into the slot until it clicks into place.
Tighten the 6-32xL3.6 screw to secure the drive to the chassis.
Connect the data and power cables to the optical drive.
Install the:
2
3
4
a
b
c
d
5
14
Removing and installing components
WLAN card
Removing the WLAN card
1
2
Remove the:
a
b
c
d
e
3
Perform the following steps to remove the WLAN card from the computer:
a
b
c
Remove the M2L3.5 screw to release the plastic tab that secures the WLAN card to the computer [1, 2].
Disconnect the WLAN cables from the connectors on the WLAN card [3].
Remove the WLAN card from its connector on the system board [4].
Installing the WLAN card
1
Insert the WLAN card to the connector on the system board.
Connect the WLAN cables to the connectors on the WLAN card.
Place the plastic tab and tighten the M2L3.5 screw to secure the WLAN card to the system board.
Install:
2
3
4
a
Removing and installing components
15
b
c
d
e
5
Heat sink
Removing the heat sink assembly
1
2
Remove the:
a
b
c
d
e
3
Follow the steps to remove the heat sink assembly:
a
b
c
Disconnect the heat sink assembly cable from the system board [1].
Remove the screws to loosen the processor fan and the heat sink [2].
Lift the heat sink and remove it from the chassis [3].
Installing the heat sink assembly
1
Place the heat sink assembly in the slot by aligning with the screw holders.
Tighten the screws to secure the heat sink assembly to the system board.
Connect the heat sink assembly cable to the system board.
Install:
2
3
4
a
b
c
d
e
16
Removing and installing components
5
Memory module
Removing the memory module
1
2
3
To remove the front memory module:
a
b
Pull the clips securing the memory module until the memory module pops up.
Remove the memory module from the system board.
Installing the memory module
1
Insert the memory module into the memory module socket until the clips secure the memory module.
2
3
Power supply unit
Removing the power supply unit (PSU)
1
2
Remove the:
a
b
c
d
e
3
Perform the following steps to remove the power supply unit (PSU) from the computer:
a
b
Disconnect the PSU cables from the connectors on the system board [1, 2].
Unroute the PSU cables from the holder [3,4].
Removing and installing components
17
4
Perform the following steps to remove the PSU:
a
b
c
Remove the 6-32xL6.35 screws that secure the PSU [1].
Press the blue release tab to release the PSU [2].
Slide and remove the PSU from the computer [3].
Installing the power supply unit (PSU)
1
Slide the PSU towards the back of the computer until it snaps into place.
Tighten the 6-32xL6.35 screws to secure the power supply unit to the computer.
Route the PSU cables through the placeholder.
2
3
4
5
Connect the PSU cables to their connectors on the system board.
Install the:
a
b
c
d
e
18
Removing and installing components
6
System fan
Removing the system fan
1
2
Remove the:
a
b
c
d
e
3
Perform the following steps to remove the system fan from the computer:
a
b
Disconnect the system fan cable from the connector on the system board [1].
Unroute the system fan cable [2].
4
Remove the M6xL10 screws that secure the system fan to the computer chassis and remove it from the computer. [1,2]
Removing and installing components
19
Installing the system fan
1
Place the system fan on the computer.
2
3
4
Tighten the M6xL10 screws to secure the system fan to the computer.
Route and connect the system fan cable to the connector on the system board.
Install the:
a
b
c
d
e
5
Coin cell battery
Removing the coin cell battery
1
2
Remove the:
a
b
c
d
20
Removing and installing components
e
3
Perform the following steps to remove the coin cell battery:
a
b
Press the release latch away from the battery to allow the battery to pop up from the socket [1].
Lift the coin cell battery out of the computer [2].
Installing the coin cell battery
1
Place the coin cell battery in its slot on the system board.
Press until the release latch springs back into place and secures it.
Install the:
2
3
a
b
c
d
e
4
System board
Removing the system board
1
2
Remove the
a
Removing and installing components
21
b
c
d
e
f
g
h
i
j
k
l
3
Disconnect the cables from the system board:
4
Follow the steps to release the I/O panel:
a
b
c
Remove the 6-32xL6.35 screw that secures the I/O panel to the chassis [1].
Press the tab to release the I/O panel from the chassis [2].
Pull the I/O panel to release the I/O panel.
22
Removing and installing components
5
Follow the steps to remove the system board:
a
b
Remove the 6-32xL6.35 screws that secure system board to the chassis [1].
Lift the system board from the chassis.
Installing the system board
1
Insert the system board and ensure that ports are aligned to the holes on the back panel.
2
Tighten the 6-32xL6.35 screws to secure the system board.
Removing and installing components
23
3
4
5
6
Push the I/O panel to its original position until it snaps in.
Tighten the 6-32xL6.35 screw to secure the I/O panel to the chassis.
Connect the cables to the system board.
Install the:
a
b
c
d
e
f
g
h
i
j
k
l
7
System board layout
1
Processor socket
PSU connector
2
4
6
8
CPU fan connector
Memory slot
3
5
7
WLAN card slot
Power button cable connector
System fan connector
Coin cell battery connector
24
Removing and installing components
9
SATA power connector
SATA2 connector
SATA1 connector
PCIex1 card slot
10
12
14
16
SATA0 connector
PSU connector
11
13
15
17
PCIex16 card slot
Clear CMOS Jumper
Clear password
Removing and installing components
25
3
Technology and components
Processors
Vostro 3267 systems are shipped with Intel 6th generation core processor technology. Vostro 3268 systems are shipped with Intel 7th
generation core processor technology.
Vostro 3267:
•
•
•
•
Intel 6th Generation Celeron G3900 (2 MB Cache, 2.80 GHz)
Intel 6th Generation Pentium G4400 (3 MB Cache, 3.30 GHz)
Intel 6th Generation Core i3-6100 (3 MB Cache, 3.70 GHz)
Intel 6th Generation Core i5-6400 (6 MB Cache, up to 3.30 GHz)
Vostro 3268:
•
•
•
•
•
Intel 7th Generation Celeron G3930 (2 MB Cache, 2.90 GHz)
Intel 7th Generation Pentium G4560 (3 MB Cache, 3.50 GHz)
Intel 7th Generation Core i3-7100 (3 MB Cache, 3.90 GHz)
Intel 7th Generation Core i5-7400 (6 MB Cache, up to 3.50 GHz)
Intel 7th Generation Core i7-7700 (8 MB Cache, up to 4.20 GHz)
NOTE: The clock speed and performance varies depending on the workload and other variables. Total cache up to 8 MB cache
depending on processor type.
Identifying processors in Windows 10
1
Tap Search the Web and Windows.
Type Device Manager.
Tap Processor.
2
3
The basic information of the processor is displayed.
Verifying the processor usage in Task Manager
1
Right click on the desktop.
2
Select Start Task Manager.
The Windows Task Manager window is displayed.
Click the Performance tab in the Windows Task Manager window.
3
26
Technology and components
Verifying the processor usage in Resource Monitor
1
Right click the desktop.
2
Select Start Task Manager.
The Windows Task Manager window is displayed.
Click the Performance tab in the Windows Task Manager window.
The processor performance details are displayed.
Click Open Resource Monitor.
3
4
Technology and components
27
Chipsets
All Desktops communicate with the CPU through the chipset. This system is shipped with the Intel 100 Series chipset.
Downloading the chipset driver
1
Turn on the computer.
2
3
Go to Dell.com/support.
Click Product Support, enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the autodetect feature or manually browse for your computer model.
Click Drivers and Downloads.
4
5
6
7
8
9
Select the operating system installed in your computer.
Scroll down the page, expand Chipset, and select your chipset driver.
Click Download File to download the latest version of the chipset driver for your computer.
After the download is complete, navigate to the folder where you saved the driver file.
Double-click the chipset driver file icon and follow the instructions on the screen.
Identifying the chipset in Device Manager on Windows 10
1
Click All Settings
on the Windows 10 Charms Bar.
2
3
From the Control Panel, select Device Manager.
Expand System Devices and search for the chipset.
28
Technology and components
Intel HD Graphics
This computer is shipped with the Intel HD Graphics graphics chipset.
Intel HD Graphics drivers
Verify if the Intel HD Graphics drivers are already installed in the computer.
Table 2. Intel HD Graphics drivers
Before installation
After installation
Display options
Identifying the display adapter
1
Start the Search Charm and select Settings.
2
3
Type Device Managerin the search box and tap Device Manager from the left pane.
Expand Display adapters.
The display adapters are displayed.
Downloading drivers
1
Turn on the computer.
2
3
Go to Dell.com/support.
Click Product Support, enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto detect feature or manually browse for your computer model.
Click Drivers and Downloads.
4
5
6
7
8
9
Select the operating system installed on your computer.
Scroll down the page and select the graphic driver to install.
Click Download File to download the graphic driver for your computer.
After the download is complete, navigate to the folder where you saved the graphic driver file.
Double-click the graphic driver file icon and follow the instructions on the screen.
Changing the screen resolution
1
Right click on the desktop and select Display Settings.
2
3
Tap or click Advanced display settings.
Select the required resolution from the drop-down list and tap Apply.
30
Technology and components
Adjusting brightness in Windows 10
To enable or disable automatic screen brightness adjustment:
1
Right click All Settings
→ System → Display.
2
Use the Adjust my screen brightness automatically slider to enable or disable automatic-brightness adjustment.
NOTE: You can also use the Brightness level slider to adjust the brightness manually.
Connecting to external display devices
Follow these steps to connect your computer to an external display device:
1
Ensure that the projector is turned on and plug the projector cable into a video port on your computer.
Press the Windows logo+P key.
2
3
Select one of the following modes:
•
•
•
•
PC screen only
Duplicate
Extend
Second Screen only
NOTE: For more information, see the document that shipped with your display device.
Hard drive options
This computer supports HDD.
Identifying the hard drive in Windows 10
1
Click All Settings
on the Windows 10 Charms Bar.
2
Click Control Panel, select Device Manager , and expand Disk drives.
The hard drive is listed under Disk drives.
Technology and components
31
Entering BIOS setup
1
Turn on or restart your laptop.
2
When the Dell logo appears, perform one of the following actions to enter the BIOS setup program:
•
With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot selection menu, tap F12.
Hard drive is listed under the System Information under the General group.
USB features
The Universal Serial Bus, or well known as USB was introduced to the PC world in 1996 which dramatically simplified the connection
between host computer and peripheral devices such as mice and keyboards, external hard drive or optical devices, Bluetooth and many
more peripheral devices in the market.
Let's take a quick look on the USB evolution referencing to the table below.
Table 3. USB evolution
Type
Data Transfer Rate
4.8 Gbps
Category
Introduction Year
USB 3.0
USB 2.0
USB 1.1
USB 1.0
Super Speed
High Speed
Full Speed
Low Speed
2010
2000
1998
1996
480 Mbps
12 Mbps
1.5 Mbps
USB 3.0 (SuperSpeed USB)
For years, the USB 2.0 has been firmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and
yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0 finally has the
answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.0 features are as follows:
•
•
•
•
•
•
Higher transfer rates (up to 4.8 Gbps)
Increased maximum bus power and increased device current draw to better accommodate power-hungry devices
New power management features
Full-duplex data transfers and support for new transfer types
Backward USB 2.0 compatibility
New connectors and cable
The topics below cover some of the most commonly asked questions regarding USB 3.0.
32
Technology and components
Speed
Currently, there are 3 speed modes defined by the latest USB 3.0 specification. They are Super-Speed, Hi-Speed and Full-Speed. The new
SuperSpeed mode has a transfer rate of 4.8Gbps. While the specification retains Hi-Speed, and Full-Speed USB mode, commonly known
as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to maintain backward
compatibility.
USB 3.0 achieves the much higher performance by the technical changes below:
•
•
An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).
USB 2.0 previously had four wires (power, ground, and a pair for differential data); USB 3.0 adds four more for two pairs of differential
signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.
•
USB 3.0 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold increase in
theoretical bandwidth.
With today's ever increasing demands placed on data transfers with high-definition video content, terabyte storage devices, high
megapixel count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the
480Mbps theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum.
Similarly, USB 3.0 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with overheads. At
this speed, USB 3.0 is a 10x improvement over USB 2.0.
Applications
USB 3.0 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB video was
barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine that with
5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps throughput.
Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will find its way into some
products that previously weren't USB territory, like external RAID storage systems.
Listed below are some of the available SuperSpeed USB 3.0 products:
•
•
External Desktop USB 3.0 Hard Drives
Portable USB 3.0 Hard Drives
Technology and components
33
•
•
•
•
•
•
•
•
USB 3.0 Drive Docks & Adapters
USB 3.0 Flash Drives & Readers
USB 3.0 Solid-state Drives
USB 3.0 RAIDs
Optical Media Drives
Multimedia Devices
Networking
USB 3.0 Adapter Cards & Hubs
Compatibility
The good news is that USB 3.0 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all, while USB 3.0
specifies new physical connections and thus new cables to take advantage of the higher speed capability of the new protocol, the
connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as before. Five new
connections to carry receive and transmitted data independently are present on USB 3.0 cables and only come into contact when
connected to a proper SuperSpeed USB connection.
Windows 8 will be bringing native support for USB 3.0 controllers. This is in contrast to previous versions of Windows, which continue to
require separate drivers for USB 3.0 controllers.
Microsoft announced that Windows 7 would have USB 3.0 support, perhaps not on its immediate release, but in a subsequent Service
Pack or update. It is not out of the question to think that following a successful release of USB 3.0 support in Windows 7, SuperSpeed
support would trickle down to Vista. Microsoft has confirmed this by stating that most of their partners share the opinion that Vista should
also support USB 3.0.
Super-Speed support for Windows XP is unknown at this point. Given that XP is a seven-year-old operating system, the likelihood of this
happening is remote.
HDMI 1.4
This topic explains the HDMI 1.4 and its features along with the advantages.
HDMI (High-Definition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an
interface between any compatible digital audio/video source, such as a set-top box, DVD player, or A/V receiver and a compatible digital
audio and/or video monitor, such as a digital TV (DTV). The intended applications for HDMI are set-top boxes, TVs, and DVD players. The
primary advantage is cable reduction and content protection provisions. HDMI supports standard, enhanced, or high-definition video, plus
multichannel digital audio on a single cable.
NOTE: The HDMI 1.4 will provide 5.1 channel audio support.
HDMI 1.4 Features
•
HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled
devices without a separate Ethernet cable
•
Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio
system, eliminating the need for a separate audio cable
•
•
3D - Defines input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications
Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings
based on content type
•
•
•
Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics.
HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p
Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique demands
of the motoring environment while delivering true HD quality
34
Technology and components
Advantages of HDMI
•
Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.
•
Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a
simple, cost-effective manner
•
•
Audio HDMI supports multiple audio formats, from standard stereo to multichannel surround sound
HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables
currently used in A/V systems
•
HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality
Memory features
In this computer, the memory (RAM) is a part of the system board.
•
•
This computer supports 2133 MHz DDR4 for Vostro-3267 system.
This computer supports DDR4 2133 MHz / 2400 MHzf or Vostro-3268 system.
NOTE: If this product is purchased with Intel 6th Gen CPUs or 7th Gen Celeron dual core CPU, the maximum MHz this product
can achieve is 2133, though the memory material used is 2400 MHz.
Verifying system memory
Windows 10
1
Clickthe Windows button and select All Settings
> System .
2
Under System, click About.
Verifying system memory in setup
1
Turn on or restart your computer..
2
Perform one of the following actions after the Dell logo is displayed:
•
With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot selection menu, tap F12.
3
On the left pane, select Settings > General > System Information,
The memory information is displayed on the right pane.
DDR4
DDR4 (double data rate fourth generation) memory is a higher-speed successor to the DDR2 and DDR3 technologies and allows up to 512
GB in capacity, compared to the DDR3's maximum of 128 GB per DIMM. DDR4 synchronous dynamic random-access memory is keyed
differently from both SDRAM and DDR to prevent the user from installing the wrong type of memory into the system.
DDR4 needs 20 percent less or just 1.2 volts, compared to DDR3 which requires 1.5 volts of electrical power to operate. DDR4 also
supports a new, deep power-down mode that allows the host device to go into standby without needing to refresh its memory. Deep
power-down mode is expected to reduce standby power consumption by 40 to 50 percent.
Technology and components
35
Key Specifications
The table below shows the specifications comparison between DDR3 vs. DDR4:
Table 4. DDR3 vs DDR4
Feature/Option
Chip Densities
Data rates
DDR3
DDR4
DDR 4 Advantages
512 Mb-8 Gb
800 Mb/s-2133 Mb/s
1.5 V
4 Gb-16 Gb
1600 Mb/s-3200 Mb/s
1.2 V
Larger DIMM capacities
Migration to higher speed I/O
Voltage
Reduced memory power
demand
Low voltage standard
Internal banks
Yes (DDR3L at 1.35V)
8
Anticipated at 1.05V
16
Memory Power Reductions
Higher data rates
Bank groups (BG)
0
4
Faster burst accesses
VREF inputs
2 —DQs and CMD/ADDR
300 Mhz-800 Mhz
10MHz – 125MHz (optional)
AL+CL
1 — CMD/ADDR
667Mhz-1.6Ghz
Undefined to 125MHz
AL+CL
VREFDQ Now Internal
Higher data rates
tCK — DLL Enabled
tCK — DLL Disabled
Read Latency
DLL-off now fully supported
Expanded values
Write Latency
AL+CWL
AL+CWL
Expanded values
DQ Driver (ALT)
DQ Bus
40&Omega
48&Omega
Optimal for PtP Applications
Less I/O Noise and Power
Support for higher data rates
Ease of use
SSTL15
POD12
RTT Values (in Ω)
RTT not allowed
ODT Modes
120,60,40,30,20
READ Bursts
240,120,80,60,48,40,34
Disables during READ Bursts
Nominal, Dynamic,Park
Nominal, Dynamic
Add’l Control Mode; OTF Value
Change
ODT Control
ODT Signaling Required
ODT Signaling Not Required
Ease of ODT Control; Allows
Non-ODT Routing, PtP Apps
Multi-Purpose Register
DIMM Types
Four Registers – 1 Defined, 3
RFU
Four Registers – 3 Defined, 1
RFU
Provides Additional Specialty
Readout
RDIMM, LRDIMM, UDIMM,
SODIMM
RDIMM, LRDIMM, UDIMM,
SODIMM
DIMM Pins
RAS
240 (R, LR, U); 204 (SODIMM) 288 (R, LR, U); 260 (SODIMM)
ECC
CRC, Parity, Addressability,
GDM
More RAS features; improved
data integrity
DDR4 Details
There are subtle differences between DDR3 and DDR4 memory modules, as listed below.
Key notch difference
36
Technology and components
The key notch on a DDR4 module is in a different location from the key notch on a DDR3 module. Both notches are on the insertion edge
but the notch location on the DDR4 is slightly different, to prevent the module from being installed into an incompatible board or platform.
Figure 1. Notch difference
Increased thickness
DDR4 modules are slightly thicker than DDR3, to accommodate more signal layers.
Figure 2. Thickness difference
Curved edge
DDR4 modules feature a curved edge to help with insertion and alleviate stress on the PCB during memory installation.
Figure 3. Curved edge
Troubleshooting
Memory errors on the system display the new ON-FLASH-FLASH or ON-FLASH-ON failure code. If all memory fails, the LCD does not
turn on. Troubleshoot for possible memory failure by trying known good memory modules in the memory connectors on the bottom of the
system or under the keyboard, as in some portable systems.
Testing memory using ePSA
1
Turn on or restart your computer.
2
Perform one of the following actions after the Dell logo is displayed:
•
With keyboard — Press F2.
The PreBoot System Assessment (PSA) starts on your computer.
Technology and components
37
NOTE: If you wait too long and the operating system logo appears, continue to wait until you see the desktop. Turn off
the computer and try again.
Realtek HD audio drivers
Verify if the Realtek audio drivers are already installed in the computer.
Table 5. Realtek HD audio drivers
Before installation
After installation
38
Technology and components
4
Troubleshooting your computer
You can troubleshoot your computer using indicators like diagnostic lights, beep codes, and error messages during the operation of the
computer.
Diagnostics
The computer POST (Power On Self Test) ensures that it meets the basic computer requirements and the hardware is working
appropriately before the boot process begins. If the computer passes the POST, the computer continues to start in a normal mode.
However, if the computer fails the POST, the computer emits a series of LED codes during the start-up. The system LED is integrated on
the Power button.
The following table shows different light patterns and what they indicate.
Table 6. Diagnostics
Number of LED flashes
2 amber
Beep code
Problem description
2
No memory or RAM detected
Memory or RAM failure
CMOS battery failure
4 amber
4
5 amber
5
3 amber, 4 white
3 amber, 3 white
3,4
3,3
Recovery image invalid
Recovery image not found
Diagnostic error messages
Table 7. Diagnostic error messages
Error messages
Description
AUXILIARY DEVICE FAILURE
The touchpad or external mouse may be faulty. For an external
mouse, check the cable connection. Enable the Pointing Device
option in the System Setup program.
BAD COMMAND OR FILE NAME
Ensure that you have spelled the command correctly, put spaces in
the proper place, and used the correct path name.
CACHE DISABLED DUE TO FAILURE
CD DRIVE CONTROLLER FAILURE
The primary cache internal to the microprocessor has failed.
The optical drive does not respond to commands from the
computer.
DATA ERROR
The hard drive cannot read the data.
DECREASING AVAILABLE MEMORY
One or more memory modules may be faulty or improperly seated.
Reinstall the memory modules or, if necessary, replace them.
DISK C: FAILED INITIALIZATION
The hard drive failed initialization. Run the hard drive tests in Dell
Diagnostics.
Troubleshooting your computer
39
Error messages
Description
DRIVE NOT READY
The operation requires a hard drive in the bay before it can
continue. Install a hard drive in the hard drive bay.
ERROR READING PCMCIA CARD
The computer cannot identify the ExpressCard. Reinsert the card
or try another card.
EXTENDED MEMORY SIZE HAS CHANGED
The amount of memory recorded in non-volatile memory (NVRAM)
does not match the memory module installed in the computer.
Restart the computer. If the error appears again, Contact Dell
THE FILE BEING COPIED IS TOO LARGE FOR THE
DESTINATION DRIVE
The file that you are trying to copy is too large to fit on the disk, or
the disk is full. Try copying the file to a different disk or use a larger
capacity disk.
A FILENAME CANNOT CONTAIN ANY OF THE FOLLOWING
CHARACTERS: \ / : * ? " < > | -
Do not use these characters in filenames.
GATE A20 FAILURE
A memory module may be loose. Reinstall the memory module or, if
necessary, replace it.
GENERAL FAILURE
The operating system is unable to carry out the command. The
message is usually followed by specific information. For example,
Printer out of paper. Take the appropriate
action.
HARD-DISK DRIVE CONFIGURATION ERROR
HARD-DISK DRIVE CONTROLLER FAILURE 0
The computer cannot identify the drive type. Shut down the
computer, remove the hard drive, and boot the computer from an
optical drive. Then, shut down the computer, reinstall the hard
drive, and restart the computer. Run the Hard Disk Drive tests in
Dell Diagnostics.
The hard drive does not respond to commands from the computer.
Shut down the computer, remove the hard drive, and boot the
computer from an optical drive. Then, shut down the computer,
reinstall the hard drive, and restart the computer. If the problem
persists, try another drive. Run the Hard Disk Drive tests in Dell
Diagnostics.
HARD-DISK DRIVE FAILURE
The hard drive does not respond to commands from the computer.
Shut down the computer, remove the hard drive, and boot the
computer from an optical drive. Then, shut down the computer,
reinstall the hard drive, and restart the computer. If the problem
persists, try another drive. Run the Hard Disk Drive tests in Dell
Diagnostics.
HARD-DISK DRIVE READ FAILURE
INSERT BOOTABLE MEDIA
The hard drive may be defective. Shut down the computer, remove
the hard drive, and boot the computer from an optical. Then, shut
down the computer, reinstall the hard drive, and restart the
computer. If the problem persists, try another drive. Run the Hard
Disk Drive tests in Dell Diagnostics.
The operating system is trying to boot to non-bootable media, such
as an optical drive. Insert bootable media.
INVALID CONFIGURATION INFORMATION-PLEASE RUN
SYSTEM SETUP PROGRAM
The system configuration information does not match the hardware
configuration. The message is most likely to occur after a memory
module is installed. Correct the appropriate options in the system
setup program.
KEYBOARD CLOCK LINE FAILURE
For external keyboards, check the cable connection. Run the
Keyboard Controller test in Dell Diagnostics.
40
Troubleshooting your computer
Error messages
Description
KEYBOARD CONTROLLER FAILURE
For external keyboards, check the cable connection. Restart the
computer, and avoid touching the keyboard or the mouse during
the boot routine. Run the Keyboard Controller test in Dell
Diagnostics.
KEYBOARD DATA LINE FAILURE
KEYBOARD STUCK KEY FAILURE
For external keyboards, check the cable connection. Run the
Keyboard Controller test in Dell Diagnostics.
For external keyboards or keypads, check the cable connection.
Restart the computer, and avoid touching the keyboard or keys
during the boot routine. Run the Stuck Key test in Dell
Diagnostics.
LICENSED CONTENT IS NOT ACCESSIBLE IN
MEDIADIRECT
Dell MediaDirect cannot verify the Digital Rights Management
(DRM) restrictions on the file, so the file cannot be played.
MEMORY ADDRESS LINE FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated. Reinstall the
memory module or, if necessary, replace it.
MEMORY ALLOCATION ERROR
The software you are attempting to run is conflicting with the
operating system, another program, or a utility. Shut down the
computer, wait for 30 seconds, and then restart it. Run the
program again. If the error message still appears, see the software
documentation.
MEMORY DOUBLE WORD LOGIC FAILURE AT ADDRESS,
READ VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated. Reinstall the
memory module or, if necessary, replace it.
MEMORY ODD/EVEN LOGIC FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated. Reinstall the
memory module or, if necessary, replace it.
MEMORY WRITE/READ FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated. Reinstall the
memory module or, if necessary, replace it.
NO BOOT DEVICE AVAILABLE
The computer cannot find the hard drive. If the hard drive is your
boot device, ensure that the drive is installed, properly seated, and
partitioned as a boot device.
NO BOOT SECTOR ON HARD DRIVE
NO TIMER TICK INTERRUPT
A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics.
NOT ENOUGH MEMORY OR RESOURCES. EXIT SOME
PROGRAMS AND TRY AGAIN
You have too many programs open. Close all windows and open the
program that you want to use.
OPERATING SYSTEM NOT FOUND
Reinstall the operating system. If the problem persists, Contact
Dell.
OPTIONAL ROM BAD CHECKSUM
SECTOR NOT FOUND
The operating system cannot locate a sector on the hard drive. You
may have a defective sector or corrupted File Allocation Table
(FAT) on the hard drive. Run the Windows error-checking utility to
check the file structure on the hard drive. See Windows Help and
Support for instructions (click Start > Help and Support). If a large
number of sectors are defective, back up the data (if possible), and
then format the hard drive.
SEEK ERROR
The operating system cannot find a specific track on the hard drive.
Troubleshooting your computer
41
Error messages
Description
SHUTDOWN FAILURE
A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics. If the message reappears,
TIME-OF-DAY CLOCK LOST POWER
TIME-OF-DAY CLOCK STOPPED
System configuration settings are corrupted. Connect your
computer to an electrical outlet to charge the battery. If the
problem persists, try to restore the data by entering the System
Setup program, then immediately exit the program. If the message
The reserve battery that supports the system configuration
settings may require recharging. Connect your computer to an
electrical outlet to charge the battery. If the problem persists,
TIME-OF-DAY NOT SET-PLEASE RUN THE SYSTEM SETUP
PROGRAM
The time or date stored in the system setup program does not
match the system clock. Correct the settings for the Date and
Time options.
TIMER CHIP COUNTER 2 FAILED
A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics.
UNEXPECTED INTERRUPT IN PROTECTED MODE
The keyboard controller may be malfunctioning, or a memory
module may be loose. Run the System Memory tests and the
X:\ IS NOT ACCESSIBLE. THE DEVICE IS NOT READY
Insert a disk into the drive and try again.
System error messages
Table 8. System error messages
System message
Description
Alert! Previous attempts at booting this system
have failed at checkpoint [nnnn]. For help in
resolving this problem, please note this
The computer failed to complete the boot routine three
consecutive times for the same error.
checkpoint and contact Dell Technical Support
CMOS checksum error
CPU fan failure
RTC is reset, BIOS Setup default has been loaded.
CPU fan has failed.
System fan failure
Hard-disk drive failure
Keyboard failure
System fan has failed.
Possible hard disk drive failure during POST.
Keyboard failure or loose cable. If reseating the cable does not solve
the problem, replace the keyboard.
No boot device available
No bootable partition on hard disk drive, the hard disk drive cable is
loose, or no bootable device exists.
•
If the hard drive is your boot device, ensure that the cables are
connected and that the drive is installed properly and
partitioned as a boot device.
•
Enter system setup and ensure that the boot sequence
information is correct.
No timer tick interrupt
A chip on the system board might be malfunctioning or
motherboard failure.
42
Troubleshooting your computer
System message
Description
NOTICE - Hard Drive SELF MONITORING SYSTEM has
reported that a parameter has exceeded its
normal operating range. Dell recommends that
you back up your data regularly. A parameter
out of range may or may not indicate a
potential hard drive problem
S.M.A.R.T error, possible hard disk drive failure.
Troubleshooting your computer
43
5
System Setup overview
System Setup allows you to:
•
•
•
Change the system configuration information after you add, change, or remove any hardware in your computer.
Set or change a user-selectable option such as the user password.
Read the current amount of memory or set the type of hard drive installed.
Before you use System Setup, it is recommended that you write down the System Setup screen information for future reference.
CAUTION: Unless you are an expert computer user, do not change the settings for this program. Certain changes can cause
your computer to work incorrectly.
Topics:
•
•
Accessing System Setup
1
Turn on (or restart) your computer.
2
After the white Dell logo appears, press F2 immediately.
The System Setup page is displayed.
NOTE: If you wait too long and the operating system logo appears, wait until you see the desktop. Then, shut down or
restart your computer and try again.
NOTE: After the Dell logo appears, you can also press F12 and then select BIOS setup.
System setup options
NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not appear.
General screen options
This section lists the primary hardware features of your computer.
Option
Description
System Information
•
•
•
System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership Tag, Ownership Date,
Manufacture Date, and the Express Service Code.
Memory Information: Displays Memory Installed, Memory Available, Memory Speed, Memory Channels Mode,
Memory Technology, DIMM A Size, DIMM B Size.
Processor Information: Displays Processor Type, Core Count, Processor ID, Current Clock Speed, Minimum
Clock Speed, Maximum Clock Speed, Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit
technology.
44
System Setup overview
Option
Description
•
Device Information: Displays Primary Hard Drive, SATA-0, M.2PCIe SSD-0, Dock eSATA Device, LOM MAC
Address, Video Controller, Video BIOS Version, Video Memory, Panel Type, Native Resolution, Audio
Controller, WiFi Device, WiGig Device, Cellular Device, Bluetooth Device.
Boot Sequence
Boot Sequence
Allows you to change the order in which the computer attempts to find an operating
system. The options are:
•
Windows Boot Manager
By default, all the options are checked. You can also deselect any option or change the
boot order.
Boot List Options
Allows you to change the boot list option:
•
•
Legacy
UEFI
Advanced Boot
Options
This option allows you the legacy option ROMs to load. By default, the Enable Legacy Option ROMs is disabled.
Date/Time
Allows you to change the date and time.
System Configuration screen options
Option
Description
Integrated NIC
Allows you to configure the integrated network controller. The options are:
•
•
•
Disabled
Enabled
Enabled w/PXE: This option is enabled by default.
SATA Operation
Allows you to configure the internal SATA hard-drive controller. The options are:
•
•
Disabled
AHCI
: This option is enabled by default.
Drives
Allows you to configure the SATA drives on board. All drives are enabled by default. The options are:
•
•
•
SATA-0
SATA-1
SATA-2
SMART Reporting This field controls whether hard drive errors for integrated drives are reported during system startup. This
technology is part of the SMART (Self-Monitoring Analysis and Reporting Technology) specification. This option is
disabled by default.
•
Enable SMART Reporting
USB Configuration This field configures the integrated USB controller. If Boot Support is enabled, the system is allowed to boot any
type of USB Mass Storage Devices (HDD, memory key, floppy).
System Setup overview
45
Option
Description
If USB port is enabled, device attached to this port is enabled and available for OS.
If USB port is disabled, the OS cannot see any device attached to this port.
•
•
•
Enable Boot Support
Enable Front USB Ports
Enable Rear USB Ports
NOTE: USB keyboard and mouse always work in the BIOS setup irrespective of these settings.
Front USB
This field field enables or disables the rear USB configuration
Configuration
•
•
•
•
Rear Port 1(Bottom Left): This option is enabled by default.
Rear Port 2 (Bottom Right): This option is enabled by default.
Rear Port 1 (Top Left): This option is enabled by default.
Rear Port 2 (Top Right): This option is enabled by default.
Rear USB
This field field enables or disables the front USB configuration
Configuration
•
•
Front Port 1(Left): This option is enabled by default.
Front Port 2 (Right): This option is enabled by default.
Audio
This field enables or disables the integrated audio controller. By default, the Enable Audio option is selected. The
options are:
•
Enable Microphone: This option is enabled by default.
Miscellaneous
Devices
Allows you to enable or disable the following devices:
•
•
Enable Camera
Enabled Secure Digital (SD) Card
NOTE: All devices are enabled by default.
Video screen options
Option
Description
Primary Display
This option option determines which video controller becomes the primary display when multiple controllers are
available in the system
•
•
Auto: This option is enabled by default.
Intel HD Graphics: This option is enabled by default.
Security screen options
Option
Description
Admin Password
Allows you to set, change, or delete the administrator (admin) password.
46
System Setup overview
Option
Description
NOTE: You must set the admin password before you set the system or hard drive password. Deleting
the admin password automatically deletes the system password and the hard drive password.
NOTE: Successful password changes take effect immediately.
Default setting: Not set
System Password
Allows you to set, change, or delete the system password.
NOTE: Successful password changes take effect immediately.
Default setting: Not set
Internal HDD-0
Password
Allows you to set, change, or delete the password on the system's internal hard-disk drive.
NOTE: Successful password changes take effect immediately.
Default Setting: Not set
Strong Password
Allows you to enforce the option to always set strong passwords.
Default Setting: Enable Strong Password is not selected.
NOTE: If Strong Password is enabled, the Admin and System passwords must contain at least one
uppercase character, one lowercase character and be at least 8 characters long.
Password
Allows you to determine the minimum and maximum length of the Administrator and System passwords.
Configuration
Password Bypass
Allows you to enable or disable the permission to bypass the System and the Internal HDD password, when they
are set. The options are:
•
•
Disabled
Reboot bypass
Default setting: Disabled
Password Change
Allows you to enable the disable permission to the System and Hard Drive passwords when the admin password is
set.
Default setting: Allow Non-Admin Password Changes is selected.
UEFI Capsule
Firmware Update
This option controls whether the system allows the BIOS updates through UEFI capsule update packages. This
option is disabled by default.
Non-Admin Setup
Changes
Allows you to determine whether changes to the setup options are allowed when an Administrator Password is
set. If disabled the setup options are locked by the admin password.
TPM 2.0 Security
Allows you to enable the Trusted Platform Module (TPM) during POST. The options are:
•
•
•
•
•
•
•
•
TPM On (enabled by default)
Clear
PPI Bypass for Enabled Commands
PPI Bypass for Disabled Commands
Attestation Enable (enabled by default)
Key Storage Enable (enabled by default)
SHA-256 (enabled by default)
Disabled
System Setup overview
47
Option
Description
•
Enabled (enabled by default)
•
Optional hardware TPM 2.0
NOTE: To upgrade or downgrade TPM1.2/2.0, download the TPM wrapper tool (software).
Computrace
Allows you to activate or disable the optional Computrace software The options are:
•
•
•
Deactivate
Disable
Activate
NOTE: The Activate and Disable options will permanently activate or disable the feature and no further
changes are allowed
Default setting: Deactivate
CPU XD Support
Allows you to enable the Execute Disable mode of the processor.
Enable CPU XD Support (default)
Admin Setup
Lockout
Allows you to prevent users from entering the setup when an Administrator password is set.
Default Setting: Enable Admin Setup Lockout is not selected.
Secure Boot screen options
Option
Description
Secure Boot Enable This option enables or disables the Secure Boot feature.
•
•
Disabled
Enabled
Default setting: Enabled.
Expert Key
Allows you to manipulate the security key databases only if the system is in Custom Mode. The Enable Custom
Management
Mode option is disabled by default. The options are:
•
•
•
•
PK
KEK
db
dbx
If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx appear. The options are:
•
•
•
•
•
•
Save to File—Saves the key to a user-selected file.
Replace from File—Replaces the current key with a key from a user-selected file.
Append from File—Adds a key to the current database from a user-selected file
Delete—Deletes the selected key
Reset All Keys—Resets to default setting
Delete All Keys—Deletes all the keys
NOTE: If you disable the Custom Mode, all the changes made are erased and the keys restore to
default settings.
48
System Setup overview
Intel Software Guard Extensions screen options
Option
Description
Intel SGX Enable
This field specifies you to provide a secured environment for running code/storing sensitive information in the
context of the main OS. The options are:
•
•
Disabled
Enabled
Default setting: Disabled
Enclave Memory
Size
This option sets SGX Enclave Reserve Memory Size. The options are:
•
•
•
32 MB
64 MB
128 MB
Performance screen options
Option
Description
Multi Core Support This field specifies whether the process has one or all cores enabled. The performance of some applications
improve with the additional cores. This option is enabled by default. Allows you to enable or disable multi-core
support for the processor. The installed processor supports two cores. If you enable Multi Core Support, two
cores are enabled. If you disable Multi Core Support, one core is enabled.
•
•
•
•
All (enabled by default)
1
2
3
Intel SpeedStep
C-States Control
Allows you to enable or disable the Intel SpeedStep feature.
Enable Intel SpeedStep
•
Default setting: The option is enabled.
Allows you to enable or disable the additional processor sleep states.
•
C states
Default setting: The option is enabled.
Limited CPUID
Value
This field limits the maximum value the processor standard CPUID function supports.
•
Enable CPUID Limit
Allows you to enable or disable the Intel TurboBoost mode of the processor.
Enable Intel TurboBoost
Intel TurboBoost
•
System Setup overview
49
Option
Description
Default Setting: The option is enabled.
Power Management screen options
Option
Description
AC Behavior
Allows you to enable or disable the computer from turning on automatically when an AC adapter is connected.
•
•
•
Power Off (default)
Power On
Last Power State
Auto On Time
Allows you to set the time at which the computer must turn on automatically. The options are:
•
•
•
•
Disabled
Every Day
Weekdays
Select Days
Default setting: Disabled
Deep Sleep Control Allows you to aggressive the system is at conserving power while Shut down (S5) or in Hybernate (S4) mode.
•
•
•
Disabled (default)
Enabled in S5 only
Enabled in S4 and S5
USB Wake Support Allows you to enable USB devices to wake the system from Standby.
NOTE: This feature is only functional when the AC power adapter is connected. If the AC power
adapter is removed during Standby, the system setup removes power from all the USB ports to
conserve battery power.
•
Enable USB Wake Support
Default setting: The option is disabled.
Wake on LAN/
WLAN
Allows you to enable or disable the feature that powers on the computer from the Off state when triggered by a
LAN signal.
•
•
•
•
•
Disabled: This option is enabled by default.
LAN Only
WLAN Only
LAN or WLAN
LAN with PXE Boot
Block Sleep
This option lets you block entering to sleep (S3 state) in operating system environment.
Block Sleep (S3 state)
Default setting: This option is disabled
50
System Setup overview
Option
Description
Intel Ready Mode
Allows you to replace sleep S3 to put your PC in an always aware state that allows the user to interact with it even
while the PC is asleep
•
Eanble Intel Ready Mode: The option is disabled.
POST Behavior screen options
Option
Description
Numlock LED
This option option specifies whether the NumLock LED should be on when the system boots.
•
Enable Numlock LED: The option is enabled.
This option option specifies whether the keyboard related errors are reported when it boots.
Enables Keyboard Error Detection: The option is disabled.
Allows you to speed up the boot process by bypassing some of the compatibility steps. The options are:
Keyboard Errors
Fastboot
•
•
•
•
Minimal(default)
Thorough
Auto
Virtualization support screen options
Option
Description
Virtualization
Allows you to enable or disable the Intel Virtualization Technology.
Enable Intel Virtualization Technology (default).
VT for Direct I/O
Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware capabilities provided
by Intel® Virtualization technology for direct I/O.
Enable VT for Direct I/O - enabled by default.
Maintenance screen options
Option
Description
Service Tag
Asset Tag
Displays the Service Tag of your computer.
Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default.
This field controls the SERR message mechanism. Some graphic card required the SERR message.
SERR Messages
•
Enable SERR Messages (default)
BIOS Downgrade
This field controls flashing of the system firmware to pervious revisions.
Allows BIOS Downgrade (Enabled by default)
System Setup overview
51
Option
Description
Data Wipe
BIOS Recovery
This field enables user to erase data from all internal storage device.
Allows you to recover from certain corrupted BIOS conditions from a recover file on the user primary hard drive or
an external USB key. Enabled by default.
System Log screen options
Option
Description
BIOS Events
Allows you to view and clear the System Setup (BIOS) POST events.
SupportAssist System Resolution screen options
Option
Description
Auto OS Recovery Allows you to control the automatic boot flow for SupportAssist System. Options are:
Threshold
•
•
•
•
Off
1
2 (Enabled by default)
3
SupportAssist OS
Recovery
Allows you to recover the SupportAssist OS Recovery (Disabled by default)
52
System Setup overview
6
Specifications
NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For
more information about the configuration of your computer, go to Help and Support in your Windows operating system and
select the option to view information about your computer.
Processor
Feature
Specification
Type
For Vostro 3267:
•
•
•
•
Intel 6th Generation Celeron G3900
Intel 6th Generation Pentium G4400
Intel 6th Generation Core i3-6100
Intel 6th Generation Core i5-6400
For Vostro 3268:
•
•
•
•
•
Intel 7th Generation Celeron G3930
Intel 7th Generation Pentium G4560
Intel 7th Generation Core i3-7100
Intel 7th Generation Core i5-7400
Intel 7th Generation Core i7-7700
System information
Feature
Chipset
Intel H110
Memory
Feature
Specification
Memory module
connector
Two DDR4 U-DIMM slots
Memory module
capacity
2 GB, 4 GB, and 8 GB
Type
2133 MHz for Vostro 3267 system
2400 MHz for Vostro 3268 systems
NOTE: If this product is purchased with Intel 6th Gen CPUs or 7th Gen Celeron dual core CPU, the
maximum MHz this product can achieve is 2133, though the memory material used is 2400 MHz.
Minimum memory
2 GB
Specifications
53
Feature
Specification
NOTE: Depending on the operating system installed, the requirement of the minimum memory might
vary.
Maximum memory
16 GB
NOTE: Each UDIMM slot supports a maximum of 8 GB memory.
Video
Feature
Specification
Integrated Controller Intel HD graphics
Integrated video
memory
Shared system memory
Discrete video
PCI express x16 graphics card
NVIDIA GT 710 LP(Low Profile) with 2 GB memory DDR3
•
Audio
Feature
Specification
Type
Integrated 5.1 high-definition audio
Communication
Feature
Specification
Type
•
•
•
Dell Wireless Combo Card DW1707 and DW1810ac, and Intel 3165ac
10/100/1000 Gigabit Ethernet
Bluetooth v4.0 +LE
Expansion bus
Feature
Specification
SATA
6 Gbps for hard drive; 1.5 Gbps for optical drive
USB 2.0
USB 3.0
480 Mbps
5 Gbps
Drives
Feature
Specification
Externally Accessible One
— 5.25–inch optical
drive bays
54
Specifications
Feature
Specification
Internally Accessible One 3.5–inch or Two 2.5-inch drive bays
— 3.5–inch/2.5–
inch drive bays
Cards
Feature
Specification
PCIe
•
•
one PCIe x16 full height card
one PCIe x1 full height card
M2 Slot
One M.2 card slot for Wi-Fi and Bluetooth combo card
External connectors
Feature
Specification
Audio — Back panel Three
Audio — Front
Panel
One headset connector
Network
One RJ-45 connector
USB — Back panel Four USB 2.0 connectors
USB — Front Panel Two USB 3.0 connectors
Video
•
•
one 15-hole VGA connector
one 19-pin HDMI connector
Memory-card reader One
Control Lights And Diagnostic Lights
Feature
Specification
Power button light
•
•
White light—solid white light indicates power-on state; blinking white light indicates sleep/stand-by state of
the computer.
Amber light—solid amber light indicates boot failure - System Power Error; blinking amber light indicates boot
failure - System Power OK.
Drive activity light
White light—blinking white light indicates that the computer is reading data from, or writing data to the hard drive.
Power
Feature
Specification
Coin-cell battery
Input voltage
Input frequency
3 V CR2032 lithium coin-cell
100 VAC — 240 VAC
50 Hz–60 Hz
Specifications
55
Feature
Specification
3 A
Input current
Output current
3.34 A / 4.62 A
Maximum heat
dissipation
NOTE: Heat dissipation is calculated by using the power supply wattage rating.
Physical Dimensions of Chassis
Feature
Height
Width
Specification
293.1 mm (11.54 inches)
92.60 mm (3.65 inches)
314.5 mm (12.38 inches)
Depth
Weight—Minimum 4.40 kg (9.71 pounds)
Environmental specifications
Feature
Specification
Temperature —
Operating
10 °C to 35 °C (50 °F to 95 °F)
Temperature —
Storage
–40 °C to 65 °C (–40 °F to 149 °F)
Relative humidity
20 % to 80 % (non-condensing)
Altitude —
Operating
–15.20 m to 5000 m (–50 ft to 10,000 ft)
Altitude — Storage –15.20 m to 10668 m (–50 ft to 35,000 ft)
Airborne
G1 as defined by ISA-S71.04–1985
contaminant level
56
Specifications
7
Contacting Dell
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip,
bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services
may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
1
Go to Dell.com/support.
2
3
4
Select your support category.
Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
Select the appropriate service or support link based on your need.
Contacting Dell
57
|
Samsung Avmkc035ea User Manual
Precisionaire Flanders Pb100 0507 User Manual
Omega Vehicle Security Drn Acc User Manual
MAKITA LS1019L 02 User Manual
LG 55UH5J User Manual
HITACHI 55HDM71 User Manual
D LINK DES 810 User Manual
DELL SP2208WFP User Manual
Cuisine Yogurt Maker User Manual
BLACK DECKER KS900EL User Manual