3
4
5
f. If operating a power tool in a damp location is
unavoidable, use a Residual Current Device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Intended use
Your Black & Decker jigsaw has been designed for sawing
wood, plastics and metal. This tool is intended for consumer
use only.
3. Personal safety
Safety instructions
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
General power tool safety warnings
Warning! Read all safety warnings and all
!
instructions. Failure to follow all instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
c. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
6
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Do not touch the workpiece or the blade
immediately after operating the tool. They can
become very hot.
Be aware of hidden hazards, before cutting into
walls, floors or ceilings, check for the location of
wiring and pipes.
The blade will continue to move after releasing the
switch. Always switch the tool off and wait for the saw
blade to come to a complete standstill before putting the
tool down.
Warning! Contact with, or inhalation of dusts arising from
cutting applications may endanger the health of the operator
and possible bystanders. Wear a dust mask specifically
designed for protection against dust and fumes and ensure
that persons within or entering the work area are also
protected.
The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury and/or damage to property.
5. Service
h. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will make sure that the safety of the power tool is
maintained.
Safety of others
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a
person responsible for the their safety.
Additional power tool safety warnings
!
Warning! Additional safety warnings for jigsaws.
Children should be supervised to ensure that they do
not play with the appliance.
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
Keep hands away from cutting area. Never reach
underneath the work piece any reason. Do not insert
fingers or thumb into the vicinity of the reciprocating
blade and blade clamp. Do not stabilize the saw by
gripping the shoe.
Keep blades sharp. Dull or damaged blades may
cause the saw to swerve or stall under pressure. Always
use the appropriate type of saw blade for the workpiece
material and type of cut.
When cutting pipe or conduit, make sure that they
are free from water, electrical wiring, etc.
7
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition to
the trigger time.
Do not use optical tools to view the laser
beam.
This laser complies with class 2 according to EN 60825-
1:2007. Do not replace a laser diode with a different
type. If the laser is damaged, have the laser repaired
by an authorised repair agent.
Do not use the laser for any purpose other than
projecting laser lines.
Labels on tools
An exposure of the eye to the beam of a class 2 laser is
considered safe for a maximum of 0.25 seconds. Eyelid
reflexes will normally provide adequate protection. At
distances greater than 1m, the laser complies with class
1 and is therefore considered completely safe.
Never look into the laser beam directly and intentionally.
Do not use optical tools to view the laser beam.
Do not set up the tool where the laser beam can cross
any person at head height.
Warning!To reduce the risk of injury, the user
must read the instruction manual.
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Do not let children come near the laser.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1. Variable speed control knob
2. On/off switch
3. Lock-on button
Additional safety instructions for non-rechargeable
batteries
4. Blade storage compartment cover
5. Shoe plate locking lever
6. Dust extraction outlet
7. Shoe plate
8. Saw blade support roller
9. Pendulum stroke selector
Never attempt to open for any reason.
Do not store in locations where the temperature may
exceed 40°C.
When disposing of batteries, follow the instructions
given in the section "Protecting the environment".
Do not incinerate the batteries.
Under extreme conditions, battery leakage may occur.
When you notice liquid on the batteries, proceed as
follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
Additional features (ꢀg. A)
Additional features may be applicable depending upon the
product purchased. The additional features applicable to the
catalogue number purchased are shown in fig. A.
Assembly
Warning!Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and
that the saw blade has stopped. Used saw blades may be
hot.
Additional safety instructions for lasers
Read all of this manual carefully.
Fitting and removing the saw blade (ꢀg. B and C)
Warning!Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and
that the saw blade has stopped. Used saw blades may be
hot.
This product is not to be used by children
under 16.
Laser radiation.
Fitting the saw blade (ꢀg. B)
Hold the saw blade (10) as shown, with the teeth facing
forward.
Do not look into the laser beam.
Push and hold the blade clamp (11) down.
8
Insert the shank of the saw blade into the blade holder
(12) as far as it will go.
Release the blade clamp (11).
The shoe plate (7) can be set to a left or right bevel angle of
up to 45°.
Pull the shoe plate locking lever (5) outwards to unlock
the shoe plate (7) from the 0 deg position.
Pull the shoe plate (7) forward and set the required
bevel 15°, 30° and 45° indicated in the bevel angle
window.
Saw blade storage (fig. C)
Saw blades (10) can be stored in the storage compartment
(4) located on the side of the tool.
Open the cover of the saw blade storage
compartment (4) by holding the tab on the top of the
cover and pulling it outward.
The blades are retained in the compartment by a
magnetic strip. To remove a blade, press down on one
end of the blade to raise the other end, and remove.
Close the cover of the saw blade storage compartment
(4) and make sure that it is latched closed.
Push the shoe plate locking lever (5) back towards the
saw to lock the shoe plate (7).
To reset the shoe plate (7) for straight cuts:
Pull the shoe plate locking lever (5) outwards to unlock
the shoe plate (7).
Set the shoe plate (7) to an angle of 0° and push the
shoe plate backwards.
Push the shoe plate locking lever (5) back towards the
saw to lock the shoe plate (7).
Warning! Close the storage compartment door securely
before operating the saw.
Setting the pendulum stroke (fig. H)
Connecting a vacuum cleaner to the tool (fig. D)
Set the pendulum stroke selector (9) to the required
position.
An adaptor (13) is required to connect a vacuum cleaner or
dust extractor to the tool.
Position 0: metal and aluminium and sheet metal.
Position I: for laminates, hard wood, work tops.
Position II: for plywood and PVC/Plastics.
Position III: for soft wood and fast cutting.
Push the adaptor (13) into the dust extraction outlet (6).
Connect the vacuum cleaner hose (14) to the adaptor
(13).
Cut line blower (fig. E)
Variable speed control
To aid visibility when cutting, your jigsaw is equipped
with a cut line blower (15) which will keep the work area
clear of dust as you saw.
Set the variable speed control knob (1) to the required
speed range.
Use a high speed for wood, medium speed for
aluminium and PVC and low speed for metals other
than aluminium.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Switching on and off
To switch the tool on, press the on/off switch (2).
To switch the tool off, release the on/off switch (2).
For continuous operation, press the lock-on button (3)
and release the on/off switch (2).
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
To switch the tool off when in continuous operation,
press the on/off switch (2) and release it.
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Sawing
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Hold the tool firmly with both hands while cutting.
The shoe plate (7) should be held firmly against the material
being cut. This will help prevent the saw from jumping,
reduce vibration and minimise blade breakage.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
Let the blade run freely for a few seconds before starting
the cut.
Apply only a gentle pressure to the tool while performing
the cut.
Use
Adjusting the shoe plate for bevel cuts (fig. F and G)
Warning! Never use the tool when the shoe plate is loose or
removed.
9
Operating the laser (fig. I - L) (KS900EL unit only)
Installing the batteries (fig. I)
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
Detach the laser module (17) from the jigsaw by removing
the screw (16) and pulling the laser module forward. Insert
two new 1.5 Volt AAA alkaline batteries, making sure to
match the (+) and (-) terminals correctly. Re-attach the laser
module (17).
Use a saw blade suitable for sawing metal.
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich.
Spread a film of oil along the intended line of cut.
Adjusting the laser side-to-side (fig. J)
Note: The laser is intended as a cutting aid and does not
guarantee a precise cut.
Maintenance
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! Do not adjust the laser with the jigsaw plugged in.
Use the laser adjustment screw (18) to align the laser
line with the saw blade if needed.
Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Never let any liquid get inside the tool and never
immerse any part of the tool into liquid.
The laser visibility (power) will be reduced if the jigsaw is
overheated. The laser may not be visible when the saw is
overloaded for a prolonged period of time. The laser visibility
will gradually return to normal when the tool cools down even
when the tool is unplugged.
Warning! Do not leave the overheated laser switched ON.
Make sure that the switch is in the OFF position and remove
the batteries to remove power from the laser.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Using the laser (fig. K - L)
Connect the brown lead to the live terminal in the new
plug.
Connect the blue lead to the neutral terminal.
The laser projects the line of cut (21) on to the surface of the
workpiece.
To switch the laser on, press the button (19).
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
To switch the laser off, press the button (19) again.
Viewing from directly above the jigsaw, the line of cut (21)
can be easily followed. Should this view be restricted for any
reason, the laser can be used as an alternative cutting guide.
Protecting the environment
Use a pencil to mark the cutting line (20).
Position the jigsaw over the line (20).
Switch on the laser.
Separate collection. This product must not be
disposed of with normal household waste.
Hints for optimum use
Sawing laminates
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
When cutting laminates, splintering may occur which can
damage the presentation surface. The most common saw
blades cut on the upward stroke, therefore if the shoe plate
is sitting on the presentation surface either use a saw blade
that cuts on the downward stroke or:
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-
use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Use a fine-tooth saw blade.
Saw from the back surface of the workpiece.
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw
through this sandwich.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
10
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf.
EC declaration of conformity
MACHINERY DIRECTIVE
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
KS900E, KS900EL
Black & Decker declares that these products described
under "technical data" are in compliance with:
2006/42/EC, EN60745-1, EN60745-2-11
Batteries
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of Black
& Decker.
At the end of their useful life, discard batteries with
due care for our environment:
Do not short-circuit the battery terminals.
Do not dispose of the battery(s) in a fire as this may
result in a risk of personal injury or an explosion.
Run the battery down completely, then remove it from
the tool.
Batteries are recyclable. Place the battery(s) in a
suitable packaging to ensure that the terminals cannot
be short-circuited. Take them to any authorised repair
agent or a local recycling station.
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe,
210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
14-02-2011
Technical data
KS900E TYPE 1
KS900EL TYPE 1
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement
is in addition to and in no way prejudices your statutory
rights. The guarantee is valid within the territories of the
Member States of the European Union and the European
Free Trade Area.
Voltage
Vac 230
W 600
Rated input
No-load speed
Max. depth of cut
Wood
min-1 800-3000
mm 85
mm 5
Steel
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker
guarantees to replace defective parts, repair products
subjected to fair wear and tear or replace such products to
make sure of the minimum inconvenience to the customer
unless:
Aluminium
Weight
(with laser)
mm 15
kg 2.36
kg 2.66
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 87 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 98 dB(A), uncertainty (K) 3 dB(A)
The product has been used for trade, professional or
hire purposes.
The product has been subjected to misuse or neglect.
The product has sustained damage through foreign
objects, substances or accidents.
Vibration total values (triax vector sum)
according to EN 60745:
Cutting wood (ah CW) 10.5 m/s2, uncertainty (K) 1.5 m/s2
Cutting metal (ah CM ) 14.5 m/s2, uncertainty (K) 1.5 m/s2
,
11
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service
staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
register your new Black & Decker product and to be kept up
to date on new products and special offers. Further
information on the Black & Decker brand and our range of
12
13
14
ENGLISH
Do not forget to register your product!
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
90561196 REV 1
S/L-02/2011
|