Dell SP2208W™FP Flat Panel Monitor User's Guide
About Your Monitor
Solving Problems
Setting Up the Monitor
Appendix
Operating the Monitor
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
© 2007 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, PowerEdge, PowerVault, PowerApp, and Dell OpenManage are trademarks of Dell
Inc; Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation; Adobe is a trademark of Adobe Systems Incorporated, which may be registered in
certain jurisdictions. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product
meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Model SP2208WFP
August 2007 Rev. A00
Front View
Front panel controls
1
2
3
4
5
6
VGA LED
DVI LED
HDMI LED
Video input select
OSD menu / select button
Brightness & Contrast / Down (-) button
7
8
Auto-Adjust / Up (+) button
Power button (with power light indicator)
9
Webcam
MIC
10
Back View
Back view
Back view with monitor stand
1
VESA mounting holes (100mm) (Behind
attached base plate)
Use to mount the monitor.
2
3
4
5
6
7
Barcode serial number label
Security lock slot
Refer to this label if you need to contact Dell for technical support.
Use a security lock with the slot to help secure your monitor.
Attach the optional Dell Soundbar.
Dell Soundbar mounting brackets
Regulatory rating label
Stand removal button
List the regulatory approvals.
Press to release the stand.
Cable management hole
Help organize cables by placing them through the hole.
Side View
USB connectors (downstream)
Left side
Right side
NOTE: To use the USB connectors on your monitor, connect the USB cable to your computer and the USB upstream connector to your monitor.
Bottom View
Bottom view
Bottom view with monitor stand
1
2
Power connector
Insert the power cable.
Dell Soundbar power Connect the power cord for the Soundbar (optional).
connector
3
Audio out connector Connect the Audio cable for the Soundbar (optional).
to the soundbar
4
5
6
7
HDMI connector
DVI connector
VGA connector
Connect your computer HDMI cable.
Connect your computer DVI cable.
Connect your computer VGA cable.
USB upstream
connector
Connect the USB cable that came with your monitor to the monitor and the
computer. Once this cable is connected you can use the USB connectors on the
side and bottom of the monitor.
8
USB connector
Connect your USB devices.
Monitor Specifications
The following sections give you information about the various power management modes and pin assignments for various connectors for your monitor.
Power Management Modes
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use.
referred to as Power Save Mode*. If the computer detects input from keyboard, mouse, or other input devices, the monitor automatically resumes functioning. The
following table shows the power consumption and signaling of this automatic power saving feature:
VESA Modes
Horizontal Sync
Vertical Sync
Video
Power Indicator
Power Consumption
Normal operation (with Dell
Soundbar and USB active)
Normal operation
Active
Active
Active
Blue
75 W (maximum)
Active
Inactive
-
Active
Inactive
-
Active
Blue
Amber
Off
40 W (typical)
Less than 2 W
Less than 1 W
Active-off mode
Switch off
Blanked
-
The OSD will only function in the normal operation mode. When the menu or plus buttons are pressed in Active-off mode, one of the following messages will be di
Analog Input In Power Save Mode. Press Computer Power Button or Any Key on Keyboard or Move Mouse
OR
Digital Input In Power Save Mode. Press Computer Power Button or Any Key on Keyboard or Move Mouse
Activate the computer and the monitor to gain access to the OSD.
NOTE: This monitor is ENERGY STAR®-compliant as well as TCO '99 power management compatible.
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.
Pin Assignments
15-pin D-Sub connector
The following table shows pin assignments in the D-Sub connector:
Pin Number Monitor Side of the 15-pin Side Signal Cable
1
2
Video-Red
Video-Green
3
Video-Blue
GND
4
5
Self-Test
GND-R
GND-G
GND-B
DDC +5V
GND
6
7
8
9
10
11
12
13
GND
DDC data
H-sync
14
15
V-sync
DDC clock
24-pin Digital-only DVI Connector
NOTE: Pin 1 is at the top right.
The following table shows pin assignments in the DVI connector:
Pin Signal Assignment
Pin Signal Assignment
T.M.D.S. Data 1-
10 T.M.D.S. Data 1+
Pin Signal Assignment
17 T.M.D.S. Data 0-
18 T.M.D.S. Data 0+
1
2
3
4
5
6
7
8
T.M.D.S. Data 2-
T.M.D.S. Data 2+
9
T.M.D.S. Data 2 Shield 11 T.M.D.S. Data 1 Shield 19 T.M.D.S. Data 0 Shield
No Connect
No Connect
DDC Clock
DDC Data
12 No Connect
13 No Connect
14 +5V Power
15 Self-Test
20 No Connect
21 No Connect
22 T.M.D.S. Clock Shield
23 T.M.D.S. Clock +
24 T.M.D.S. Clock -
No Connect
16 Hot Plug Detect
19-pin HDMI Connector
The following table shows pin assignments in the HDMI connector:
Pin Signal Assignment
Pin Signal Assignment
T.M.D.S. Data 0-
T.M.D.S. Data 2 Shield 10 T.M.D.S. Clock +
Pin Signal Assignment
17 DDC/CEC Ground
18 +5V Power
1
2
3
4
5
6
7
8
T.M.D.S. Data 2-
9
T.M.D.S. Data 2+
T.M.D.S. Data 1+
11 T.M.D.S. Clock Shield
12 T.M.D.S. Clock -
19 Hot Plug Detect
T.M.D.S. Data 1 Shield 13 CEC
T.M.D.S. Data 1-
T.M.D.S. Data 0+
14 Reserved(N.C. on device)
15 SCL
T.M.D.S. Data 0 Shield 16 SDA
Universal Serial Bus (USB) Interface
This monitor supports High-Speed Certified USB 2.0 interface.
Data Rate Power Consumption
High speed 480 Mbps 2.5W (Max., each port)
Full speed 12 Mbps
Low speed 1.5 Mbps
2.5W (Max., each port)
2.5W (Max., each port)
USB Upstream Connector
Pin Number
4-pin Side of the connector
1
2
3
4
DMU
VCC
DPU
GND
USB Downstream Connector
Pin Number
4-pin Side of the connector
1
2
3
4
VCC
DMD
DPD
GND
USB ports:
l
l
1 upstream - rear
4 downstream - 2 on rear; 2 on left side
NOTE: USB 2.0 capability requires 2.0-capable computer.
NOTE: The USB interface of the monitor works ONLY when monitor is powered ON (or in Power Save Mode). Switching your monitor OFF and then ON would
enumerate its USB interface; attached peripherals may take a few seconds to resume normal functionality.
Plug and Play Capability
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identificat
(EDID) using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. Most monitor installations are automatic
can select different settings, if desired.
Flat Panel Specifications
Screen type
Active matrix - TFT LCD
22 inches (22-inch viewable image
size)
Screen dimensions
Preset display area:
Horizontal
473.76 mm (18.65 inches)
296.1 mm (11.66 inches)
0.282 mm
Vertical
Pixel pitch
160° (vertical) typ, 160° (horizontal)
typ
Viewing angle
Luminance output
Dynamic contrast ratio
Faceplate coating
Backlight
300 cd/m ²(typ)
2000 to 1 (typ)
ARC-Glare (2H)
CCFL (4) edgelight system
2ms typical (Grey to Grey)
Response Time
Camera - MIC Specifications
Overview
The integrated USB camera and digital microphones allow you to take pictures, videos, and communicate with other computer users. The camera is located at the
the monitor and is fixed. However, the camera’s software--Dell Webcam Software suite, provides limited panning abilities. When the camera is on, the blue ligh
the camera turns on.
Lens
Field of view
66.5 degree +/- 5 %
Focus mode
Fixed Focus
Focus area
49cm~Infinity
Focusing distance (normal mode)
Active array size
Video frame rate
1100 mm
Image Sensor
2.0 mega-pixel
Video specification
1600 x 1200 (UXGA) - up to 10 frames per second
640 x 480 (VGA) and below - up to 30 frames per second
Image flip
Horizontally
Digital zoom
Microphone type
2x
Audio Specification
Interface
Dual Microphone
USB 2.0 high Speed
3.3 volts+- 5%
Power Supply
System Requirements
The following are the minimum system requirements for Camera - MIC feature:
l
l
l
l
l
l
Intel® Pentium® 4 or AMD® equivalent processor running at 1.8 GHz or higher (Recommended: Intel Pentium 4, 2.8 GHz with Hyper-Threading enabled)
Microsoft® Windows® XP Service Pack 2 or Windows Vista
256 MB RAM (512 MB RAM or higher recommended)
580 MB free hard disk space
Available USB 1.1 port or a USB 1.1 hub with external power supply (USB 2.0 required for maximum frame rate and resolution)
CD-ROM/DVD-ROM drive for software installation
Dell Webcam Software Suite
The Dell Webcam Software Suite includes the following applications:
· Dell Webcam Center
Dell Webcam Center makes it easy to capture photos and video. With Webcam Center, you can perform photo and video captures, or perform advanced
tasks like remote monitoring, motion detection and time lapse video capturing.
· Dell Webcam Manager
Dell Webcam Manager is a central access point for all your webcam-related applications. Locate and launch your favorite webcam applications quickly and
easily from Webcam Manager while you use your webcam.
· Dell Webcam Console
The Dell Webcam Console provides a customized set of attractive features, such as Advanced Video and Audio Effects, face tracking and parental control,
enhancing your video chatting experience.
· Live! Cam Avatar
Live! Cam Avatar lets you disguise yourself as a superstar, a furry friend, or any customized animated character while you video chat using any instant
messaging software. The avatar tracks your head movement and lip sync anything you say instantly at the same time.
· Live! Cam Avatar Creator
Live! Cam Avatar allows you to create your very own personalized avatar from digital photos you have chosen, accompanied by the advanced speech
technology which provides lip sync to your animated avatar.
Appendix
Dell™ SP2208WFP Flat Panel Monitor User's Guide
CAUTION: Safety Instructions
CAUTION: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock,
electrical hazards, and/or mechanical hazards.
For information on safety instructions, see the Product Information Guide.
FCC Notices (U.S. Only) and Other Regulatory Information
For FCC notices and other regulatory information, see the regulatory compliance website located at www.dell.com/regulatory_compliance.
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-999-3355).
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or
Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be
available in your area. To contact Dell for sales, technical support, or customer service issues:
1. Visit support.dell.com.
2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.
3. Click Contact Us on the left side of the page.
4. Select the appropriate service or support link based on your need.
5. Choose the method of contacting Dell that is convenient for you.
Your Monitor Setup Guide
To view PDF files (files with an extension of .pdf), click the document title. To save PDF files (files with an extension of .pdf) to your hard drive, right-
click the document title, click Save Target As in Microsoft®Internet Explorer or Save Link As in Netscape Navigator, and then specify a location on your
hard drive to which you want to save the files.
Your Monitor Setup Guide(.pdf ) (58MB)
NOTE: PDF files require Adobe® Acrobat® Reader®, which can be downloaded from the Adobe Website at www.adobe.com.
To view a PDF file, launch Acrobat Reader. Then click File®Open and select the PDF file.
Setting Up Your Monitor
Dell™ SP2208WFP Flat Panel Monitor
If you have a Dell™ desktop or a Dell™ portable computer with internet access
1. Go to http://support.dell.com, enter your service tag, and download the latest driver for your graphics card.
2. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1680x1050 again.
NOTE: If you are unable to set the resolution to 1680x1050, please contact Dell™ to inquire about a Graphics Adapter that supports these resolutions.
Setting Up Your Monitor
Dell™ SP2208WFP Flat Panel Monitor
If you have non Dell™ desktop, portable computer, or graphic card
1. Right-click on the desktop and click Properties.
2. Select the Settings tab.
3. Select Advanced.
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).
5. Please refer to the graphic card provider website for updated driver (for example, http://www.ATI.com OR http://www.NVIDIA.com ).
6. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1680x1050 again.
NOTE: If you are unable to set the resolution to 1680x1050, please contact the manufacturer of your computer or consider purchasing a graphics adapter
that will support the video resolution of 1680x1050.
Operating the Monitor
Dell™ SP2208WFPFlat Panel Monitor User's Guide
Using the Front Panel
Use the buttons on the front of the monitor to adjust the image settings.
Front panel Button
Description
A
Use the Input Select button to choose between three different video signals that may be connected to your monitor.
NOTE: The floating 'Dell Self-test Feature Check' dialog appears on a black background if the monitor cannot sen
signal. Use the input select button to select the desired input source (Analog, Digital or HDMI).
If the VGA/DVI cable is disconnected from the video card, the Dell Self-test Feature Check dialogue box appears.If t
cable is disconnected from the HDMI source (DVD player, setup box, or console), the monitor enters power save m
or
Video input select
or
B
The Menu button is used to open and exit the on-screen display (OSD), and exit from menus and sub-menus. See Using t
OSD Menu/Select
C
Use these buttons to adjust (decrease/increase ranges) items in the OSD menu.
Down (-) and Up (+)
D
Use this button to launch Brightness menu.
Brightness Menu
E
Use this button to activate automatic setup and adjustment. The following dialog appears on a black screen as the monit
adjusts to the current input:
Auto Adjust In Progress
Auto Adjustment
button allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment,
further tune your monitor by using the Pixel Clock (Coarse), Phase (Fine) controls in the OSD.
Auto Adjust
NOTE: Auto Adjust does not occur if you press the button while there are no active video input signals or attached c
F
Use the Power button to turn the monitor on and off.
The blue light indicates the monitor is on and fully functional. An amber light indicates power save mode.
Power button
(with power light indicator)
Using the On-Screen Display (OSD) Menu
Accessing the Menu System
NOTE: If you change the settings and then either proceed to another menu or exit the OSD menu, the monitor automatically saves those changes. The
changes are also saved if you change the settings and then wait for the OSD menu to disappear.
1.Press the Menu button to open the OSD menu and display the main menu.
Main Menu for Auto Detect Analog (VGA) Input
Main Menu for Auto Detect Digital (DVI) Input
Main Menu for A
or
or
Main Menu for Analog (VGA) Input
Main Menu for Digital (DVI) Input
Main Men
or
or
NOTE: AUTO ADJUST is only available when you are using the analog (VGA) connector.
2. Press the - and + buttons to move between the setting options. As you move from one icon to another, the option name is highlighted. See the table
below for a complete list of all the options available for the monitor.
3. Press the Menu button once to activate the highlighted option.
4. Press - and + button to select the desired parameter.
5. Press Menu to enter the slide bar and then use the - and + buttons, according to the indicators on the menu, to make your changes.
6. Press the Menu button once to return to the main menu to select another option or Press the Menu button two or three times to exit from the OSD
menu.
Icon
Menu and Submenus
Exit
Description
Select to exit the Main menu.
Brightness/ Contrast
Brightness adjusts the luminance of the backlight.
Adjust Brightness first, then adjust Contrast only if further adjustment is necessary.
Push the + button to increase luminance and push the - button to decrease luminance (min 0 ~ max 100).
Contrast adjusts the degree of difference between darkness and lightness on the monitor screen.
Push the + button to increase the contrast and push the - button to decrease the contrast (min 0 ~ max 100).
Auto Adjust
Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display se
particular setup.
Select to activate automatic setup and adjustment. The following dialog appears on a black screen as the monitor self
input:
Auto Adjust In Progress
Auto Adjustment allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can f
by using the Pixel Clock (Coarse) and Phase (Fine) controls under Image Settings.
NOTE: In most cases, Auto Adjust produces the best image for your configuration.
NOTE: When using DVI/HDMI, Auto Adjust is not available.
Positioning:Horizontal
Vertical
Positioning moves the viewing area around on the monitor screen.
When making changes to either the Horizontal or Vertical settings, no changes occur to the size of the viewing area. T
response to your selection.
When making changes to Zoom setting, you can increase or decrease the size of image. The image scale changes in r
selection.
Minimum is 0 (-) and maximum is 100 (+).
NOTE: When using DVI/HDMI source, the Horizontal and Vertical settings are not available.
The Phase, Pixel Clock, and Sharpness adjustments allow you to more closely adjust your monitor to your preference.
in the main OSD menu to access these settings.
Image settings:
Pixel Clock (Coarse)
NOTE: Pixel Clock controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, t
vertical stripes and the images is not proportional.
Phase (Fine)
Use the - and + buttons to make adjustments. (Minimum: 0 ~ Maximum: 100)
If satisfactory results are not obtained using the Phase adjustment, use Pixel Clock (Coarse) and then use Phase (fine
NOTE: This function may change the width of the display image. Use the Horizontal function of the Position menu to
image on the screen.
The Sharpness adjustment allow you to improve the sharpness of texts. There are five levels for adjustment totally. (0
The Scaling Ratio adjustment allow you to change the image scale with various default settings.
Sharpness
Scaling Ratio
NOTE: When using DVI/HDMI source, the Pixel Clock and Phase settings are not available.
NOTE: Scaling Ratio is not available if the resolution of video signal is greater than 1680x1050. However, 16:9 and Fill
video timing.
Color Settings
Color Settings adjust the color temperature.
Color Settings has the following options:
Color Management : You can choose to enable or disable this option.
Color Settings Mode : You can choose between a Graphics and a Video mode. If your computer is connected to your m
Graphics. If a DVD, STB, or VCR is connected to your monitor, choose Video.
Color Presets: You can choose different color presets for different viewing modes.
In the Graphics mode, you can choose Normal Preset, Multimedia Preset, Gaming Preset, Red Preset, Blue Prese
Normal Preset is selected to obtain the default (factory) color settings.
l
Normal Preset
Multimedia Preset
Gaming Preset
l
l
l
Select Multimedia Preset to view media applications.
Select Gaming Preset for playing games in your computer.
Select Red Preset for a reddish tint. This color setting is used for color-intensive applications (photograph image
movies, etc.).
Red Preset
Blue Preset
User Preset
l
l
Select Blue Preset for a bluish tint. This color setting is used for text based applications (spreadsheets, program
User Preset: Use the plus and minus buttons to increase or decrease each of the three colors (R, G, B) independ
increments, from 0 to 100.
NOTE: Optimized color settings such as Multimedia and Gaming presets are unavailable when you disable Color Man
Theatre Preset
Sports Preset
Nature Preset
In Video mode, you can choose Theatre, Sports or Nature Preset;
Select Theater Preset for playing a movie.
Select Sports Preset for viewing sports.
Select Nature Preset for general viewing.
You can adjust the Hue/Saturation based on the preference.
l
l
l
l
makes video image shade into greenish.
makes video image shade into purplish.
Hue
makes video image look more monochrome.
makes video image look more colorful.
Saturation
NOTE: Optimized color settings such as Theatre, Sports and Nature presets are unavailable when you disable Color
selection.
Choose the RGB option if monitor is connected to a PC or a DVD using a VGA/DVI/HDMI cable. Choose the YPbPr+ optio
to a DVD by a YPbPr cable. HDMI uses info-frame to detect input color format (if available).
Advanced Settings
Input Color
Format
Dynamic Contrast - The feature helps get a higher contrast if you choose Gaming preset, Theatre Preset, Sports Prese
brightness is not available for user adjustment in above mode.
Dynamic Contrast
Response Time
Response Time - This function improves the response time in Multimedia preset, gaming preset, sports preset and the
On-Enable the enhancement pattern for response time.
Off-Disable the enhancement pattern for response time.
Adjust the settings for the OSD, including the location, the amount of time the menu remains on-screen.
Position of the OSD:
OSD Settings:
Horizontal
Position
l
l
To adjust the horizontal position of the OSD, use the - and + buttons, and move OSD to the left and right.
Vertical Position
To adjust the vertical position of the OSD, use the - and + buttons, and move OSD down and up.
OSD Hold Time:
OSD Hold Time
OSD Lock
The OSD stays active for as long as it is in use. Adjusting the hold time, sets the length of time the OSD remains active
pressed a button. Use the - and + buttons to adjust the slider in 5 second increments, from 5 to 60 seconds.
OSD Lock:
Controls user access to adjustments. When Yes (+) is selected, no user adjustments are allowed. All buttons are locke
button.
NOTE:When the OSD is locked, pressing the menu button takes the user directly to the OSD settings menu, with OS
No (-) to unlock and allow user access to all applicable settings.
NOTE:You can also lock or unlock the OSD by pressing and holding the Menu button for 15 seconds.
Language
Select to have the OSD display in one of the five languages (English, Spanish, French, German, or Japanese).
NOTE: The change only affects the OSD. It has no effect on any software running on the computer.
Audio (optional)
You can select to have the audio on or off when the monitor is in power saving mode.
Yes — enables audio
No — disables audio (default)
NOTE: When the Dell Soundbar is not properly connected to the monitor, the audio menu is not available.
Factory Reset:
Reset the OSD menu options to the factory preset values.
Exit — Select to exit out of Reset to Factory Settings menu without resetting any OSD options.
Position settings only — Change the settings for Image Position back to original factory settings.
Color settings only — Change the Red, Green, and Blue settings back to their default factory values. The default setti
Color Management: On
Colors Settings Mode: Graphics
Color Presets: Normal Preset
All settings — Change all the user-adjustable settings including color, position, brightness, contrast and OSD hold tim
defaults. The language of the OSD does not change.
IR — This feature will help reduce minor cases of image retention.
Enable LCD Conditioning: If an image appears to be stuck on the monitor, select LCD Conditioning to help eliminate
Using the LCD Conditioning feature may take several hours. Severe cases of image retention are known as burn-in, th
feature does not remove burn-in.
NOTE: Use LCD Conditioning only when you experience a problem with image retention.
Below warning message appears when you select “Enable LCD Conditioning”:
NOTE: Press any button on the monitor to terminate LCD Conditioning at any time.
DDC/CI — Enable the DDC/CI control function.
DDC/CI (Display Data Channel/Command Interface) allows you to adjust the monitor parameters (brightness, color ba
applications on your PC.
Default is "Enable". Select Disable to disable this feature.
For best user experience and optimum performance of your monitor, keep this feature enabled.
NOTE: If user select "Disable", display Warning message box as below. Select "Yes" disable DDC/CI
and return to "Factory Reset" menu. Warning message time-out in 20 sec.
OSD Warning Messages
One of the following warning messages may appear on the screen indicating that the monitor is out of synchronization.
or
or
or
or
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. Either the signal is too high or too low for the monitor to
use. See Specifications for the Horizontal and Vertical frequency ranges addressable by this monitor. Recommended mode is 1680 X 1050 @ 60Hz.
NOTE:The floating Dell Self-test Feature Check dialog appears on-screen if the monitor cannot sense a video signal(Only for VGA/DVI), When there is no
HDMI input, the monitor will directly entry power saving mode.
or
or
Occasionally, no warning message appears, but the screen is blank. This could also indicate that the monitor is not synchronizing with the computer.
Setting the Optimal Resolution
To set the optimal resolution for the monitor:
1. Right-click on the desktop and select Properties.
2. Select the Settings tab.
3. Set the screen resolution to 1680 x 1050.
4. Click OK.
If you do not see 1680 x 1050 as an option, you may need to update your graphics driver. Depending on your computer, complete one of the following
procedures.
l
If you have a Dell desktop or portable computer:
Go to support.dell.com, enter your service tag, and download the latest driver for your graphics card.
¡
l
If you are using a non-Dell computer (portable or desktop):
¡
¡
Go to the support site for your computer and download the latest graphic drivers.
Go to your graphics card website and download the latest graphic drivers.
Using the Dell Soundbar (Optional)
The Dell Soundbar is a stereo two channel system adaptable to mount on Dell Flat Panel Displays. The Soundbar has a rotary volume and on/off control to
adjust the overall system level, a blue LED for power indication, and two audio headset jacks.
1. Power/volume control
2. Power indicator
3. Headphone connectors
Using the Tilt
With the built-in pedestal, you can tilt the monitor for the most comfortable viewing angle.
NOTE: The stand is detached and extended when the monitor is shipped from the factory.
Using the Camera
Installing the Dell Webcam Software (Microsoft® Windows® Operating Systems)
The Dell SP2208WFP webcam application media that ships with your monitor, allows you to the install the software and drivers for the integrated webcam.
To install the Dell Webcam Software:
1.
Insert the Dell SP2208WFP Webcam Resource CD into the drive.
NOTE:Ensure that the USB cable is connected between the monitor and the computer.
2.
3.
4.
The Install Shield Wizard automatically launches the setup application. Select the Language and click Next to continue.
Read Software License Agreement and click Yes to continue.
Click Browse to change Destination Folder where the software will be installed to and then click Next to continue.
Choose Full Installation than click Next and follow the instructions to complete the installation. Alternatively, choose Custom Installation to select the
components to install.
5.
6.
Click Finish to restart the computer after installation completes.
Accessing the Camera Help File
To access the camera’s help file, right-click the Dell Webcam Center icon in the notification area and click Launch Webcam Center. Click Help from the menu and
select Contents.
Manually Adjusting the Camera Settings
If you do not want the camera to use automatic settings, you can manually adjust the camera settings.
Setting the Contrast, Brightness, and Volume
To set the contrast, brightness, and volume:
1.
2.
Right-click the Dell Webcam Manager icon in the system tray located in the lower right corner of the screen. Click Launch Webcam Console.
In the Webcam Console window:
·
·
Click the Camera tab to adjust video settings, such as contrast and brightness.
Click the Effects tab to adjust audio settings, such as the volume level.
For more information about camera settings and other camera-related topics, see the camera’s Help file (see "Accessing the Camera’s Help File").
Setting the Resolution
To set the camera resolution using the Dell Webcam Center:
Right-click the Dell Webcam Manager icon in the system tray located in the lower right corner of the screen. Click Launch Webcam Center.
The Dell Webcam Center window appears.
1.
2. Click the Video Recording tab.
Select the resolution from the Video drop-down list at the lower left hand corner. The video resolution is updated immediately. The current resolution
is indicated by a check mark.
3.
4. Click the Photo Capture tab.
Select the resolution from the Photo drop-down list at the lower left hand corner. The photo resolution is updated immediately. The current
resolution is indicated by a check mark.
5.
6. Click Finish to restart the computer after installation completes.
Resetting the Camera Defaults
To reset the Camera settings using the Dell Webcam Console:
1. Right-click the Dell Webcam Manager icon in the system tray located in the lower right corner of the screen. Click Launch Webcam Console.
The Dell Webcam Console window appears.
2. Click the Camera tab on the menu bar and then click the Reset button.
You are now ready to use the Webcam. The Webcam application provides the following functions.
l
l
l
l
l
Dell Webcam Center: Dell Webcam Center makes it easy to capture photos and video with your Dell Webcam. With Webcam Center, you can perform
photo and video captures, or perform advanced tasks such as remote monitoring, motion detection, and time lapse video capturing.
Dell Webcam Manager: Dell Webcam Manager is a central access point for all your webcam-related applications. Locate and launch your favorite
webcam applications quickly and easily from Webcam Manager while you use your webcam.
Dell Webcam Console: The Dell Webcam Console provides a customized set of attractive features, such as Advanced Video and Audio Effects, face
tracking and parental control, and enhancing your video chatting experience.
Live! Cam Avatar: Live! Cam Avatar lets you disguise yourself as a superstar, a furry friend, or any customized animated character while you video chat
using any instant messaging software. The avatar tracks your head movement and lip sync anything you say instantly at the same time.
Live! Cam Avatar Creator: Live! Cam Avatar allows you to create your very own personalized avatar from digital photos you have chosen, accompanied
by the advanced speech technology which provides lip sync to your animated avatar.
Setting Up Your Monitor
Dell™ SP2208WFP Flat Panel Monitor
Important instructions to set the display resolution to 1680X1050 (Optimal)
For optimal display performance while using the Microsoft Windows?operating systems, set the display resolution to 1680 x 1050 pixels by performing the
following steps:
1. Right-click on the desktop and click Properties.
2. Select the Settings tab.
3. Move the slider-bar to the right by pressing and holding left-mouse button and adjust the screen resolution to 1680X1050.
4. Click OK.
If you do not see 1680X1050 as an option, you may need to update your graphics driver. Please choose the scenario below that best describes the
computer system you are using, and follow the provided directions:
Dell™ SP2208WFP Flat Panel Monitor
Information in this document is subject to change without notice.
© 2007 Dell Inc. All rights reserved
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, PowerEdge, PowerVault, PowerApp, and Dell OpenManage are trademarks of Dell
Inc; Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation; Adobe is a trademark of Adobe Systems Incorporated, which may be registered in
certain jurisdictions. ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product
meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
Model SP2208WFP
August 2007 Rev. A00
Setting Up the Monitor
Dell™ SP2208WFP Flat Panel Monitor User's Guide
Attaching the Stand
NOTE: The stand is detached and extended when the monitor is shipped from the factory.
Place the stand on a flat surface and follow these steps to attach the monitor stand:
1. Fit the groove on the back of the monitor to the two tabs on the upper part of the stand.
2. Lower the monitor so that the monitor mounting area snaps on to or locks on to the stand.
Connecting The Monitor
Connecting the White DVI Cable
Connecting the Blue VGA Cable
Connecting the HDMI Cable
1. Turn off your computer and disconnect the power cable.
Connect either the white DVI or the blue VGA cable to the connectors on the computer and the monitor, or connect the HDMI to external DVD-player, set-up
boxes, or consoles.
2.
Connect the USB cable that was included with your monitor to the computer and the upstream USB connector on the monitor. Once this cable is connected to
computer and the monitor, you can use the USB connectors on the monitor.
3.
4. Connect any USB devices.
5. Connect the power cables.
Turn on your monitor and computer. If you do not see an image, push the input select button and ensure the correct input source is selected. If you still do n
6.
Organizing The Cables
After attaching all necessary cables to your monitor and computer, (See Connecting Your Monitor for cable attachment,) use the cable management hole
to organize all cables as shown above.
Attaching the Soundbar
NOTICE: Do not use with any device other than Dell Soundbar.
NOTE:Soundbar Power Connector +12V DC output is for optional Soundbar only.
1. Working from the rear of the monitor, attach Soundbar by aligning the two slots with the two tabs along the bottom rear of the monitor.
2. Slide the Soundbar to the left until it snaps into place.
3. Connect the Soundbar with the DC power connector.
4. Insert the mini stereo plug from the rear of the Dell Soundbar into the computer's audio output jack.
NOTE:To playback audio from HDMI sources, insert the mini stereo plug into the audio OUT connector at the back of the monitor
Removing the Stand
NOTE: To prevent scratches on the LCD screen while removing the stand, ensure that the monitor is placed on a clean surface.
Complete the following steps to remove the stand:
1. Rotate the stand to allow access to the stand release button.
2. Press and hold the Stand release button.
3. Lift the stand up and away from the monitor .
Solving Problems
Dell™ SP2208WFP Flat Panel Monitor User's Guide
Troubleshooting the Monitor
Self-Test Feature Check
Your monitor provides a self-test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly
connected but the monitor screen remains dark, run the monitor self-test by performing the following steps:
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer. To ensure proper Self-Test operation, remove both Digital (white connector) and the Analog (blue
connector) cables from the back of computer.
3. Turn on the monitor.
The floating dialog box should appear on-screen (against a black background) if the monitor cannot sense a video signal and is working correctly.
While in self-test mode, the power LED remains blue. Also, depending upon the selected input, one of the dialogs shown below will continuously scroll
through the screen.
or
or
4. This box also appears during normal system operation if the video cable becomes disconnected or damaged.
5. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
If your monitor screen remains blank after you use the previous procedure, check your video controller and computer, because your monitor is functioning
properly.
NOTE: Self test feature check is not available for HDMI video modes.
Common Problems
The following table contains general information about common monitor problems you might encounter and the possible solutions.
COMMON
SYMPTOMS
PROBLEM
DESCRIPTION
POSSIBLE SOLUTIONS
No Video/Power
LED off
No picture,
monitor is dead.
Check connection integrity at the both ends of the video cable, verify that the monitor and computer are plugged
into a working electrical outlet, and that you have pressed the power button.
No Video/Power
LED on
No picture or no
brightness.
l
l
l
l
l
Press the input select button in the front of the monitor and ensure the correct input source is selected.
Increase brightness & contrast controls.
Perform monitor self-test feature check.
Check for bent or broken pins on the end of the video cable.
Reboot your computer and monitor.
Poor Focus
Picture is fuzzy,
blurry, or
ghosting.
l
l
l
l
l
Push Auto Adjust button.
Adjust Phase and Clock controls via OSD.
Eliminate video extension cables.
Perform monitor reset.
Lower video resolution or increase font size.
Shaky/Jittery Video Wavy picture or
fine movement.
l
l
l
l
l
Push Auto Adjust button.
Adjust Phase and Clock controls via OSD.
Perform monitor reset.
Check environmental factors.
Relocate and test in another room.
Missing Pixels
LCD screen has
spots.
l
l
Cycle power on-off.
These are pixels that are permanently off and this is a natural defect that occurs in LCD technology.
Brightness
Problems
Picture too dim or
too bright.
l
l
l
Perform monitor reset.
Push Auto Adjust button.
Adjust brightness & contrast controls.
Geometric
Distortion
Screen not
centered
correctly.
l
l
l
l
Perform monitor reset on Position Settings Only.
Push Auto Adjust button.
Adjust the centering controls.
Ensure monitor is in proper video mode.
NOTE: When using '2: DVI-D/3:HDMI', the positioning adjustments are not available.
Horizontal/Vertical Screen has one
l
l
l
l
l
Perform monitor reset.
Push Auto Adjust button.
Adjust Phase and Clock controls via OSD.
Perform monitor self-test feature check and determine if these lines are also in self-test mode.
Check for bent or broken pins.
Lines
or more lines.
NOTE: When using '2: DVI-D/3:HDMI', the Pixel Clock and Phase adjustments are not available.
Sync Problems
Screen is
scrambled or
appears torn.
l
l
l
l
l
l
Perform monitor reset.
Push Auto Adjust button.
Adjust Phase and Clock controls via OSD.
Perform monitor self-test feature check to determine if scrambled screen appears in self-test mode.
Check for bent or broken pins.
Boot up in the Safe Mode.
LCD Scratched
Screen has
scratches or
smudges.
l
l
Turn monitor off and clean the screen.
Safety Related
Issues
Visible signs of
smoke or sparks.
l
l
Do not perform any troubleshooting steps.
Monitor needs to be replaced.
Intermittent
Problems
Monitor
malfunctions on
and off.
l
l
l
l
Ensure monitor is in proper video mode.
Ensure video cable connection to computer and to the flat panel is secure.
Perform monitor reset.
Perform monitor self-test feature check to determine if the intermittent problem occurs in self-test mode.
Image Retention
(from a static
image)
Faint Shadow
from the static
image displayed
appears on the
screen.
l
l
Use the Power Management feature to turn off the monitor at all times when not in use. Alternatively, use a
dynamically changing screensaver left on the monitor for a long period of time.
In OSD Menu, under Reset to Factory Settings, select Enable LCD Conditioning. Using this option may take
several hours before the image is eliminated.
NOTE: Image Burn-in is not covered by your warranty.
Camera Problems
COMMON
SYMPTOMS
WHAT YOU
EXPERIENCE
POSSIBLE SOLUTIONS
No Power
The camera is
not working
and the LED is
off
If the monitor has no power, see Troubleshooting Your Monitor.
Verify if the camera is detected by Windows.
Reinstall the camera drives using the Dell SP2208WFP Webcam Resource CD. See Using the Camera for more information.
Camera is not The camera is
Remove and insert the USB cable.
detected
not working
and the LED is
on
Reinstall the Dell Webcam Software and drivers. See installing your Dell Webcam Software for more information.
Poor Focus
The camera
captures fuzzy
or unclear
Verify that the protective film has been removed from the camera and the camera lens is clean.
Clean the camera surface using a damp, soft lint-free cloth.
videos and
pictures
Increase the available ambient light or change the source of light.
Reset the camera defaults through the Dell Webcam Console. See Using the Camera for more information.
Ensure that the Color Depth settings in Display Properties is set to 16-bit color or higher. NOTE: Lower color depth
settings result in poor-quality images.
NOTE: The integrated webcam operates at a lower resolution than most commercially available digital cameras. Most
commercial digital cameras are 4 mega pixel or higher. The integrated webcam operates up to 2.0 mega pixel.
Poor quality
video on the
Internet
The camera
captures
grainy images
while using it
on the
Check your internet connection speed. A slow Internet connection could cause similar problems with the video. It is
recommended to use a broadband connection with good throughput.
Internet
Color Problem The images
are tinted red,
Reset the camera defaults through the Dell Webcam Console. See Using the Camera for more information.
Adjust the camera color settings through Dell Webcam Console. See Using the Camera for more information.
blue, or green
No Image
Blank screen
Increase the available ambient light, change the direction of the camera, or change the source of light.
Reset the camera defaults through the Dell Webcam Console. See Using the Camera for more information.
Adjust the contrast levels using the Dell Webcam Console. See Using the Camera for more information.
Ensure the camera is detected correctly by the Windows operating system.
Slow frame
rate in video
The capture
video is not
The video capture especially in high resolution is a resource intensive task, reduce the video recording resolution.Select No
Compression for video in the Video Recording settings.
capture mode smooth
Install the latest DirectX and the latest webcam driver.
Audio and
video is not
The captured
video and
The video capture, especially in high resolution is a resource intensive task. Reduce the video recording resolution.Select No
Compression for video in the Video Recording settings.
synchronized audio are not
synchronized
Microphone is The webcam
Speak closer to the microphone.
not working
captures video
but not sound
The integrated microphone is designed to have a wider reception area for recording. it still has its limits. Try moving closer to
the microphone or ensure that you are within the recording area for the microphone.
Check if the volume is muted. To enable sound:
1. Click Start®Control Panel®Sound and Audio Devices.
2. Click to uncheck the box next to Mute.
Set the correct audio source in Dell Webcam Center. To select the correct audio source:
1. In the Dell Webcam Center, click Tools®Audio Source Control.
2. Select Monitor Webcam (SP2208WFP) in the Audio Source drop down list
3. Adjust the Volume slider to obtain the desired audio level.
Test the microphone. Try testing the microphone using an application other than the Dell Webcam Center. To test the
microphone,
1.Click Start®Control Panel®Sound and Audio Devices.
2.Click the Voice tab.
3.Click the Test Hardware button and follow the instructions.
If the recording is successful, reset the camera defaults or reinstall the Dell Webcam Software. See Using the Camera for
more information.
Product Specific Problems
SPECIFIC SYMPTOMS
WHAT YOU EXPERIENCE
POSSIBLE SOLUTIONS
Screen image is too small
Image is centered on screen, but does not fill
entire viewing area.
l
Perform monitor reset on All Settings.
Cannot adjust the monitor with the
buttons on the front panel
OSD does not appear on the screen.
l
Turn off the monitor, unplug the power cord and then plug
back and turn on the monitor.
NOTE: When choosing DVI-D mode, the Auto Adjust function is not available.
Universal Serial Bus (USB) Specific Problems
SPECIFIC SYMPTOMS
WHAT YOU EXPERIENCE
POSSIBLE SOLUTIONS
USB interface is not working
USB peripherals are not working.
l
l
l
Check that your monitor is turned ON.
Reconnect the upstream cable to your computer.
Reconnect the USB peripherals (downstream
connector).
l
Switch off and then turn on the monitor again.
High Speed USB 2.0 interface is
slow
High Speed USB 2.0 peripherals working slowly or not at
all.
l
l
l
l
Check that your computer is USB 2.0 capable.
Verify USB 2.0 source on your computer.
Reconnect the upstream cable to your computer.
Reconnect the USB peripherals (downstream
connector).
Troubleshooting the Dell™ Soundbar
Common Symptoms
No Sound
What You Experience
Possible Solutions
No power to Soundbar - the
power indicator is off
(built-in DC power supply. i.e.
SP2208WFP )
l
Turn the Power/Volume knob on the Soundbar clockwise to the middle position; check if
the power indicator (green LED) on the front of the Soundbar is illuminated.
Ensure that the power cable from the Soundbar is plugged into the monitor.
Ensure that the monitor has power.
problem.
l
l
l
No Sound
Soundbar has power - power
indicator is on
l
l
Plug the audio line-in cable into the computer's audio out jack.
Set all volume controls to their maximum and ensure that the mute option is not
enabled.
l
l
l
l
Play some audio content on the computer (example, audio CD, or MP3).
Turn the Power/Volume knob on the Soundbar clockwise to a higher volume setting.
Clean and reseat the audio line-in plug.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
Distorted Sound
Computer's sound card is used
as the audio source
l
l
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound
card.
l
l
l
Set all Windows volume controls to their midpoints.
Decrease the volume of the audio application.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume
setting.
l
l
l
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
Avoid using an audio cable extension or audio jack converter.
l
Distorted Sound
Other audio source is used
l
l
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the audio
source.
l
l
Decrease the volume of the audio source.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume
setting.
l
Clean and reseat the audio line-in plug.
Unbalanced Sound Output
Sound from only one side of
Soundbar
l
l
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound card
or audio source.
l
l
l
l
Set all Windows audio balance controls (L-R) to their midpoints.
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
Low Volume
Volume is too low
l
l
Clear any obstructions between the Soundbar and the user.
Turn the Power/Volume knob on the Soundbar clockwise to the maximum volume
setting.
l
l
l
Set all Windows volume controls to their maximum.
Increase the volume of the audio application.
Test the Soundbar using another audio source (For example: portable CD player, MP3
player).
|