Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
OperatOr’s Manual
Two Stage Snow Thrower — 2X 524 WE, 2X 524 SWE,
2X 526 SWE, 2X 528 SWE & 2X 530 SWE
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Printed In USA
Form No. 769-09763
(May 29, 2014)
Important Safe Operation Practices
2
WARNING! This symbol points out important safety instructions which, if not followed,
could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!
CALIFORNIA PROPOSITION 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.
DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing foreign objects. Failure to observe the following safety
instructions could result in serious injury or death.
Training
Preparation
1.
Read, understand, and follow all instructions on the
Thoroughly inspect the area where the equipment is to be used.
Remove all doormats, newspapers, sleds, boards, wires and other
foreign objects, which could be tripped over or thrown by the
auger/impeller.
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
1.
Always wear safety glasses or eye shields during operation
and while performing an adjustment or repair to protect
your eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
2.
3.
Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.
Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and be trained and supervised by an
adult.
2.
Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.
4.
5.
Never allow adults to operate this machine without proper
instruction.
3.
4.
Use a grounded three-wire extension cord and receptacle
for all machines with electric start engines.
Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
Adjust auger housing height to clear gravel or crushed rock
surfaces.
5.
6.
Disengage all control levers before starting the engine.
6.
7.
Keep bystanders, pets and children at least 75 feet from the
machine while it is in operation. Stop machine if anyone
enters the area.
Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
Exercise caution to avoid slipping or falling, especially
when operating in reverse.
7.
Let engine and machine adjust to outdoor temperature
before starting to clear snow.
3
5.
Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
Safe Handling of Gasoline
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.
6.
7.
Do not operate machine while under the influence of
alcohol or drugs.
Muffler and engine become hot and can cause a burn. Do
not touch. Keep children away.
a. Use only an approved gasoline container.
8.
9.
Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
b. Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
Exercise caution when changing direction and while
operating on slopes. Do not operate on steep slopes.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is
hot or running.
10. Plan your snow-throwing pattern to avoid discharge
towards windows, walls, cars etc. Thus, avoiding possible
property damage or personal injury caused by a ricochet.
e. Allow engine to cool at least two minutes before
refueling.
11. Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
f.
Never over fill fuel tank. Fill tank to no more than ½
inch below bottom of filler neck to provide space for
fuel expansion.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
g. Replace gasoline cap and tighten securely.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
h. If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
14. Disengage power to the auger/impeller when transporting
or not in use.
i.
Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
(e.g. furnace, water heater, space heater, clothes
dryer etc.).
15. Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use care
when backing up.
j.
Allow machine to cool at least 5 minutes before
storing.
16. If the machine should start to vibrate abnormally, stop
the engine, disconnect the spark plug wire and ground it
against the engine. Inspect thoroughly for damage. Repair
any damage before starting and operating.
k. Never fill containers inside a vehicle or on a truck
or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.
17. Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments,
or inspections.
l.
If possible, remove gas-powered equipment from
the truck or trailer and refuel it on the ground. If this
is not possible, then refuel such equipment on a
trailer with a portable container, rather than from a
gasoline dispenser nozzle.
18. Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the
discharge opening. Do not unclog chute assembly while
engine is running. Shut off engine and remain behind
handles until all moving parts have stopped before
unclogging.
m. Keep the nozzle in contact with the rim of the fuel
tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
Operation
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
1.
2.
3.
4.
Do not put hands or feet near rotating parts, in the auger/
impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
20. When starting engine, pull cord slowly until resistance
is felt, then pull rapidly. Rapid retraction of starter cord
(kickback) will pull hand and arm toward engine faster than
you can let go. Broken bones, fractures, bruises or sprains
could result.
The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
21. If situations occur which are not covered in this manual, use
care and good judgment. Contact Customer Support for
assistance and the name of your nearest servicing dealer.
Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
4
Section 2 — important Safe operation practiceS
14. According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years,
or 60 hours of operation. At the end of the Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety
systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.
Clearing a Clogged Discharge Chute
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with snow
throwers. Never use your hand to clean out the discharge chute.
To clear the chute:
1.
2.
SHUT THE ENGINE OFF!
Wait 10 seconds to be sure the impeller blades have
stopped rotating.
Do not modify engine
3.
Always use a clean-out tool, not your hands.
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Maintenance & Storage
1.
Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and
adjustment sections of this manual.
Notice Regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
2.
Before cleaning, repairing, or inspecting machine
disengage all control levers and stop the engine. Wait until
the auger/impeller come to a complete stop. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting.
3.
4.
5.
Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
Spark Arrestor
WARNING! This machine is equipped with an
internal combustion engine and should not be used
on or near any unimproved forest-covered, brush
covered or grass-covered land unless the engine’s
exhaust system is equipped with a spark arrestor
meeting applicable local or state laws (if any).
Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
If a spark arrestor is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrestor for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
6.
Check control levers periodically to verify they engage
and disengage properly and adjust, if necessary. Refer
to the adjustment section in this operator’s manual for
instructions.
7.
8.
9.
Maintain or replace safety and instruction labels, as
necessary.
Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper
instructions on off-season storage.
12. Check fuel line, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
13. Do not crank engine with spark plug removed.
Section 2 — important Safe operation practiceS
5
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.
Symbol
Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to
assemble and operate
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running. There are rotating
blades inside
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running. There are rotating
blades inside
WARNING— ROTATING AUGER
Do not put hands or feet near rotating parts, in the auger/impeller housing or chute
assembly. Contact with the rotating parts can amputate hands and feet.
WARNING—THROWN OBJECTS
This machine may pick up and throw objects which can cause serious personal injury.
WARNING—GASOLINE IS FLAMMABLE
Allow the engine to cool at least two minutes before refueling.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
WARNING— ELECTRICAL SHOCK
Do not use the engine’s electric starter in the rain
WARNING— HOT SURFACE
Engine parts, especially the muffler, become extremely hot during operation. Allow engine
and muffler to cool before touching.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
6
Section 2 — important Safe operation practiceS
Assembly & Set-Up
3
Contents of Carton
•
•
•
One Snow Thrower
•
•
Two Replacement Auger Shear Pins
One Product Registration Card
•
•
One Chute Assembly
One Chute Control Rod
One Engine Operator’s Manual
One Snow Thrower Operator’s
Manual
Assembly
Remove all loose parts before assembling.
Handle Assembly
1.
2.
Place the shift lever in the Forward-6 position
Observethelowerrearareaofthesnowthrowertobesureboth
cables are aligned with roller guides before pivoting the
handle upward. Pivot the handle upward. See Figure 3-1.
Figure 3-2
Chute Assembly
1.
Removehairpinclip,wingnutandhexscrewfromchutecontrol
head and clevis pin and bow-tie cotter pin from chute
support bracket. See Figure 3-3.
Chute Control Head
Figure 3-1
NOTE: Make certain the cables are seated properly in the
roller guides. See Figure 3-2.
Chute Support
Bracket
3.
Secure the handle by tightening the plastic knob located
on both the left and right sides of the handle. Remove
and discard any rubber bands, if present. They are for
packaging purposes only.
Chute
Chute Base
Figure 3-3
7
2.
Insertchutecontrolrodintochutecontrolhead.Pushrodasfar 4.
into chute control head as possible, keeping the holes in
the rod pointing upward. See Figure 3-4.
Squeezethetriggeronthejoystickandrotatethechutebyhand
to face forward. The holes in the chute control input will be
facing up. See Figure 3-6.
Chute Control
Top View
Input
Figure 3-4
Figure 3-6
3.
Place chute onto chute base and ensure chute control rod
is positioned under the handle panel. Install hex bolt
previously removed but do not secure with wing nut at this
NOTE: The chute will not rotate without squeezing the
trigger on the joystick.
5.
Rotatethejoysticktotheoneo’clockpositionsothatthesilver
indicator arrow on the pinion gear below the control panel
faces upward. See Figure 3-7.
time. See Figure 3-5.
Figure 3-5
Figure 3-7
NOTE: The joystick will be angled slightly to the right at the
one o’clock position. See “Top View” in Figure 3-6.
8
Section 3— ASSembly & Set-Up
6.
Insert the chute control rod into the pinion gear below the
joystick. Make sure to line up the hole in the rod with the
arrow on the pinion gear. See Figure 3-8.
NOTE: The chute control rod will fit snuggly into the pinion
gear. Support the rear of the dash panel with one hand
while inserting the rod with your other hand to ensure the
rod is inserted all the way into the pinion gear.
NOTE: The hole is a reference for aligning the rod with the
indicator arrow on the pinion gear, and will be visible after
the rod has been inserted.
Figure 3-9
NOTE: The second hole is used to achieve further
engagement of the chute control rod into the pinion
gear if required. Refer to page 18 for Chute Control Rod
adjustments.
8.
9.
Finish securing chute control head to chute support
bracket with wing nut, clevis pin, and bow-tie cotter pin
removed in step 1. See Figure 3-3.
Checkthatallcablesareproperlyroutedthroughthecableguide
on top of the engine. See Figure 3-10.
Figure 3-8
NOTE: For smoothest operation, the cables should all be to
the left of the chute directional control rod.
7.
Push the chute control rod toward the control panel until the
hole in the rod lines up with the hole in the chute control
input closest to the chute control head and insert the
hairpin clip removed earlier. See Figure 3-9.
NOTE: Models with 2-Way Chute Control have only one
cable to route through the cable guide.
Figure 3-10
Section 3 — ASSembly & Set-Up
9
Chute Directional Control (If Equipped)
Chute Clean-Out Tool
1.
Remove the plastic cap (if present), flat washer and hairpin
clip from the end of the chute directional control. See
Figure 3-11.
The chute clean-out tool is fastened to the top of the auger
housing with a mounting clip and a cable tie at the factory. Cut
the cable tie before operating the snow thrower. See Figure 3-13.
A
Chute Clean-out Tool
B
Figure 3-11
Figure 3-13
2.
Insert the end of the chute directional control into the lower
bracket and secure with the flat washer and hairpin clip just
removed. If necessary, the lower bracket can be adjusted.
Refer to Chute Bracket Adjustment in the Service section.
Tire Pressure
WARNING: Under any circumstance do not exceed
manufacturer’s recommended psi. Equal tire
pressure should be maintained at all times. Excessive
pressure when seating beads may cause tire/rim
assembly to burst with force sufficient to cause
serious injury. Refer to sidewall of tire for
recommended pressure.
Set-Up
Shear Pins
A pair of replacement auger shear pins and bow tie cotter pins
are included with your snow thrower. Store them in your snow
thrower’s dash panel until needed. See Figure 3-12.
The tires are over-inflated for shipping purposes. Check the tire
pressure before operating the snow thrower. Refer to the tire side
wall for tire manufacturer’s recommended psi and deflate (or
inflate) the tires as necessary.
NOTE: Equal tire pressure is to be maintained at all times for
performance purposes.
Figure 3-12
10
Section 3— ASSembly & Set-Up
Adjustments
Auger Control
WARNING! Prior to operating your snow thrower,
Skid Shoes
carefully read and follow all instructions below.
Perform all adjustments to verify your snow thrower
is operating safely and properly.
The snow thrower skid shoes are adjusted upward at the factory
for shipping purposes. Adjust them downward, if desired, prior to
operating the snow thrower.
Check the adjustment of the auger control as follows:
CAUTION: It is not recommended that you operate
this snow thrower on gravel as it can easily pick up and
throw loose gravel, causing personal injury or damage
to the snow thrower and surrounding property.
1.
When the auger control is released and in the disengaged
“up” position, the cable should have very little slack. It
should NOT be tight.
2.
In a well-ventilated area, start the snow thrower engine.
Refer to the Engine Operator’s Manual packed with your
snow thrower.
•
•
For close snow removal on a smooth surface, raise skid
shoes higher on the auger housing.
Use a middle or lower position when the area to be cleared
is uneven, such as a gravel driveway
3.
4.
While standing in the operator’s position (behind the snow
thrower), engage the auger.
NOTE: If you choose to operate the snow thrower on a gravel
surface, keep the skid shoes in position for maximum clearance
between the ground and the shave plate.
Allow the auger to remain engaged for approximately ten
(10) seconds before releasing the auger control. Repeat this
several times.
To adjust the skid shoes:
5.
6.
With the throttle control in the FAST (rabbit) position and
the auger control in the disengaged “up” position, walk to
the front of the machine.
1.
Loosen the four hex nuts (two on each side) and carriage
bolts. Move skid shoes to desired position. See Figure 3-14.
Confirm that the auger has completely stopped rotating
and shows NO signs of motion. If the auger shows ANY
signs of rotating, immediately return to the operator’s
position and shut off the engine. Wait for ALL moving parts
to stop before re-adjusting the auger control.
7.
To readjust the control cable, loosen the upper hex screw
on the auger cable bracket. See Figure 3-15.
Figure 3-14
2.
3.
Makecertaintheentirebottomsurfaceofskidshoeisagainstthe
ground to avoid uneven wear on the skid shoes.
Retighten nuts and bolts securely.
Figure 3-15
8.
9.
Position the bracket upward to provide more slack (or
downward to increase cable tension).
Retighten the upper hex screw.
10. Repeat steps 2 through 6 above to verify proper
adjustment has been achieved.
Section 3 — ASSembly & Set-Up
11
Controls and Features
4
Drive Control
Shift Lever
4-Way Chute Directional Control/
Chute Tilt Control †
Auger Control
Headlight
Heated Grips †
Steering Trigger Control †
Chute Assembly
Clean Out
Tool
Standard Chute Directional
Control †
Augers
† If Equipped
Skid Shoe
Figure 4-1
Snow thrower controls and features are described below and
illustrated in Figure 4-1.
Skid Shoes
Position the skid shoes based on surface conditions. Adjust
upward for hard-packed snow. Adjust downward when
operating on gravel or crushed rock surfaces. See Set-Up &
Assembly section.
Shift Lever
The shift lever is located in the right side of the
handle panel and is used to determine ground
speed and direction of travel.
Augers
Forward
When engaged, the augers rotate and draw snow into the auger
housing.
There are six forward (F) speeds. Position one (1) is
the slowest and position six (6) is the fastest.
Chute Assembly
Snow drawn into the auger housing is discharged out the chute
assembly.
Reverse
There are two reverse (R) speeds. One (1) is the
slower and two (2) is the faster.
Headlight
The headlight is located on the handle panel and is automatically
turned on when the engine is started.
12
Auger Control
Heated Grips (If so Equipped)
CAUTION: It is recommended that you wear
gloves when using the heated grip. If the heated
grip become too hot, turn it off.
To activate the heated grips, move the switch found on the rear
of the dash panel into the ON position. To turn off the heated
grips, move the switch found on the rear of the dash panel to the
OFF position.
The auger control is located on the left handle. Squeeze the
control grip against the handle to engage the augers and start
snow throwing action. Release to stop.
Steering Trigger Controls (If so Equipped)
Drive Control / Auger Clutch Lock
The left and right wheel steering trigger controls are located on
the underside of the handles.
The drive control is located on the right handle. Squeeze the
control grip against the handle to engage the wheel drive.
Release to stop.
•
•
Squeeze the right control to turn right.
Squeeze the left control to turn left.
The drive control also locks the auger control so that you can
operate the chute directional control without interrupting
the snow throwing process. If the auger control is engaged
simultaneously with the drive control, the operator can release
the auger control (on the left handle) and the augers will remain
engaged. Release both controls to stop the augers and wheel
drive.
CAUTION: Operate the snow thrower in open
areas until you are familiar with these controls.
Note: Always release the drive control before changing speeds.
Failure to do so will result in increased wear on your machine’s
drive system.
Section 4 — controlS and FeatureS
13
4-Way Chute Directional Control (If so Equipped)
Chute Clean-Out Tool
WARNING! Never use your hands to clear a
clogged chute assembly. Shut off engine and remain
behind handles until all moving parts have stopped
before unclogging.
The chute clean-out tool is conveniently fastened to the rear of
the auger housing with a mounting clip. Should snow and ice
become lodged in the chute assembly during operation, proceed
as follows to safely clean the chute assembly and chute opening:
1.
2.
Release both the Auger Control and the Drive Control.
Stop the engine. Refer to the Engine Operator’s Manual.
Remove the key.
3.
4.
Remove the clean-out tool from the clip which secures it to
the rear of the auger housing.
Use the shovel-shaped end of the clean-out tool to
dislodge and scoop any snow and ice which has formed in
and near the chute assembly.
The chute directional control is located on the left side of the
dash panel.
•
To change the direction in which snow is thrown, squeeze
the button on the joy-stick and pivot the joy-stick to the
right or to the left.
5.
Refasten the clean-out tool to the mounting clip on the
rear of the auger housing, reinsert the key and start the
snow thrower’s engine.
•
To change the angle/distance which snow is thrown, pivot
the joy-stick forward or backward.
While standing in the operator’s position (behind the snow
thrower), engage the auger control for a few seconds to clear any
remaining snow and ice from the chute assembly.
Chute Directional Control/Chute Tilt Control
(If so Equipped)
CHUTE DIRECTIONAL CONTROL
DISCHARGE
RIGHT
DISCHARGE
LEFT
CHUTE TILT
DOWN
CHUTE TILT
UP
The chute directional control is located on left side of the snow
thrower. The chute tilt control is located on the left side of the
dash panel.
•
To change the direction in which snow is thrown, rotate
chute directional control.
•
To change the angle/distance which snow is thrown, pivot
the joy-stick forward or backward.
14
Section 4 — controlS and FeatureS
Operation
5
Starting and Stopping the Engine
Refer to the Engine Operator’s Manual packed with your snow
thrower for instructions on starting and stopping the engine.
Replacing Shear Pins
The augers are secured to the spiral shaft with shear pins and
cotter pins. If the auger should strike a foreign object or ice jam,
the snow thrower is designed so that the pins may shear. If the
augers will not turn, check to see if the pins have sheared. See
Figure 5-2.
To Engage Drive
1.
With the throttle control in the Fast (rabbit) position, move
shift lever into one of the six forward (F) positions or two
reverse (R) positions. Select a speed appropriate for the
snow conditions and a pace you’re comfortable with.
2.
Squeeze the drive control against the handle the snow
thrower will move. Release it and drive motion will stop.
To Engage Augers
To engage the augers and start throwing snow, squeeze the
auger control against the left handle. Release to stop the augers.
To Steer (If so Equipped)
With the drive control engaged, squeeze the right steering
trigger control to turn right. Squeeze the left steering trigger
control to turn left.
CAUTION: Operate the snow thrower in open
areas and at slow speeds until you are familiar with
the drive control and comfortable operating the
steering controls.
Engage Heated Grips (If so Equipped)
Figure 5-2
CAUTION: NEVER replace the auger shear pins
with anything other than OEM Part No.738-04124A
replacement shear pins. Any damage to the auger
gearbox or other components as a result of failing to
do so will NOT be covered by your snow thrower’s
warranty.
CAUTION: It is recommended that you wear
gloves when using the heated grip. If the heated
grip become too hot, turn it off.
To activate the heated grips, move the switch found on the rear
of the dash panel into the ON position. See Figure 5-1.
WARNING! Always turn off the snow thrower’s
engine and remove the key prior to replacing shear
pins.
Figure 5-1
15
Maintenance & Adjustments
6
Maintenance
Lubrication
Engine
Wheels
Refer to the Engine Operator’s Manual.
At least once a season, remove both wheels. Clean and coat the
axles with a multipurpose automotive grease before reinstalling
wheels.
Tire Pressure
Refer to Assembly and Set-up section for information regarding
tire pressure.
Auger Shaft
At least once a season, remove the shear pins from the auger
shaft. Spray lubricant inside the shaft and around the spacers and
the flange bearings found at either end of the shaft.
See Figure 6-2.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the snow
thrower are subject to wear. They should be checked periodically
and replaced when necessary.
NOTE: The skid shoes on this machine have two wear edges.
When one side wears out, they can be rotated 180° to use the
other edge
To remove skid shoes:
1.
Remove the four carriage bolts and hex flange nuts which
secure them to the snow thrower.
2.
Reassemble new skid shoes with the four carriage bolts
(two on each side) and hex flange nuts. Refer to Figure 6-1.
Figure 6-2
Gear Shaft
The gear (hex) shaft should be lubricated at least once a season
or after every twenty-five (25) hours of operation.
1.
2.
Allow the engine to run until it is out of fuel.
Carefully pivot the snow thrower up and forward so that it
rests on the auger housing.
NOTE: Augers not shown for clarity.
3.
Remove the frame cover from the underside of the snow
thrower by removing the self-tapping screws which secure
it. Refer to Figure 6-3.
Figure 6-1
To remove shave plate:
1.
Remove the carriage bolts and hex nuts which attach it to
the snow thrower housing.
2.
Reassemble new shave plate, making sure heads of carriage
bolts are to the inside of housing. Tighten securely.
16
Figure 6-3
Figure 6-5
4.
Apply a light coating of Bostik Regular Grade Never-Seez®
to the hex shaft. See Figure 6-4.
3.
4.
Pivot the bracket downward to take up slack in the cable.
Retighten the hex nut.
Auger Control
Refer to the Assembly and Set-up section for instructions on
adjusting the auger control cable.
Skid Shoes
Refer to the Assembly and Set-up section for instructions on
adjusting the skid shoes.
Drive Control
When the drive control is released and in the disengaged “up”
position, the cable should have very little slack. It should NOT be
tight.
NOTE: If excessive slack is present in the drive cable or if the snow
thrower’s drive is disengaging intermittently during operation,
the cable may be in need of adjustment.
Check the adjustment of the drive control as follows:
1.
With the drive control released, push the snow thrower
gently forward. The unit should roll freely.
2.
Engage the drive control and gently attempt to push the
snow thrower forward. The wheels should not turn. The
unit should not roll freely.
Figure 6-4
NOTE: When lubricating the hex shaft, be careful not to get
any oil on the aluminum drive plate or the rubber friction
wheel. Doing so will hinder the snow thrower’s drive
system. Wipe off any excess or spilled oil.
3.
With the drive control released, move the shift lever back
and forth between the R2 position and the F6 position
several times. There should be no resistance in the shift
lever.
Adjustments
If any of the above tests failed, the drive cable is in need of
adjustment. Proceed as follows:
Shift Cable
If the full range of speeds (forward and reverse) cannot be
achieved, adjust the shift cable as follows:
1.
Shut off the engine as instructed in the separate engine
manual.
1.
2.
Place the shift lever in the fastest forward speed position.
Loosen the hex nut on the shift cable index bracket. See
Figure 6-5.
Section 6 — Maintenance & adjuStMentS
17
2.
Loosen the lower hex screw on the drive cable bracket. See
Figure 6-6.
Chute Control Rod
To adjust the chute control rod, proceed as follows:
1.
2.
Remove the hairpin clip from the hole closest to the chute
assembly on the chute rotation assembly.
Pull out the chute control rod until the hole in it lines up
with the second hole in the chute rotation assembly. See
Figure 6-8.
Figure 6-6
3.
Position the bracket upward to provide more slack (or
downward to increase cable tension).
4.
5.
Retighten the upper hex screw.
Check the adjustment of the drive control as described
above to verify proper adjustment has been achieved.
Figure 6-8
3.
Reinsert the hairpin clip through this hole and the chute
control rod. See Figure 6-8.
Chute Bracket Adjustment (If so Equipped)
If the spiral at the bottom of the chute directional control is not
fully engaging with the chute assembly, the chute bracket can be
adjusted. To do so:
Off-Season Storage
If the snow thrower will not be used for 30 days or longer, follow
the storage instructions below.
1.
Loosen the two nuts which secure the chute bracket and
reposition it slightly. See Figure 6-7.
1.
2.
3.
Lubricate the machine as instructed earlier in this section.
Store in a clean, dry area.
If storing the snow thrower in an unventilated area,
rustproof the machine using a light oil or silicone to coat
the snow thrower.
4.
Clean the exterior of the engine and the snow thrower.
NOTE: Refer to the Engine Operator’s Manual for information on
storing your engine.
Figure 6-7
2.
Retighten the nuts.
18
Section 6 — Maintenance & adjuStMentS
Service
7
3.
Loosen and remove the two bolts and flat washers securing
the belt guide. See Figure 7-2. Remove belt guide.
Belt Replacement
Auger Belt
To remove and replace your snow thrower’s auger belt, proceed
as follows:
1.
Allow the engine to run until it is out of fuel. Do not
attempt to pour fuel from the engine.
2.
Remove the plastic belt cover on the front of the engine by
removing the two self-tapping screws. See Figure 7-1.
Figure 7-2
4.
Roll the auger belt off the engine pulley. See Figure 7-3.
Figure 7-1
Figure 7-3
19
5.
6.
Carefully pivot the snow thrower up and forward so that it
rests on the auger housing.
8.
Remove the belt from around the auger pulley, and slip the
belt between the support bracket and the auger pulley.
See Figure 7-6.
Remove the frame cover from the underside of the snow
thrower by removing the self-tapping screws which secure
it. See Figure 7-4.
NOTE: Engaging the auger control will ease removal and
reinstallation of the belt.
Figure 7-4
Figure 7-6
7.
Loosen and remove the shoulder bolt which acts as a belt
keeper. See Figure 7-5.
9.
Replace the auger belt by following instructions in reverse
order.
NOTE: Do not forget to reinstall the shoulder bolt and
reconnect the spring to the frame after installing a
replacement auger belt.
10. After replacing the auger belt, perform the Auger Control
test on page 11 of the Assembly and Set-Up section.
Figure 7-5
20
Section 7 — Service
Drive Belt
Friction Wheel Removal
NOTE: Special tools are required and several components must
be removed in order to replace the snow thrower’s drive belt. See
your authorized service dealer to have the drive belt replaced or
phone Customer Support as instructed on page 2 for assistance.
(524 WE)
If the snow thrower fails to drive with the drive control engaged,
and performing the drive control cable adjustment fails to
correct the problem, the friction wheel may need to be replaced.
Follow the instructions below. Examine the friction wheel for
signs of wear or cracking and replace if necessary:
Friction Wheel Inspection
(524 SWE, 526 SWE, 528 SWE & 530 SWE)
If the snow thrower fails to drive with the drive control engaged,
and performing the drive control cable adjustment fails to
correct the problem, the friction wheel may need to be replaced.
1.
Allow the engine to run until it is out of fuel. Do not
attempt to pour fuel from the engine.
2.
3.
Place the shift lever in first Forward (F1) position.
Carefully pivot the snow thrower up and forward so that it
rests on the auger housing.
NOTE: Special tools are required and several components must
be removed in order to replace the snow thrower’s friction wheel
rubber. See your authorized service dealer to have the friction
wheel rubber replaced or phone Customer Support as instructed
on page 2 for assistance.
4.
Remove the frame cover from the underside of the snow
thrower by removing the self-tapping screws which secure
it. Remove the right-hand wheel by removing the screw
and bell washer which secure it to the axle. See Figure 7-7.
To inspect the friction wheel, proceed as follows:
1.
2.
3.
Allow the engine to run until it is out of fuel. Do not
attempt to pour fuel from the engine.
Carefully pivot the snow thrower up and forward so that it
rests on the auger housing.
Remove the frame cover from the underside of the snow
thrower by removing four self-tapping screws which secure
it. See Figure 7-4.
4.
Examine the friction wheel for signs of wear or cracking.
Figure 7-7
Section 7 — Service
21
5.
Carefully remove the hex nut which secures the hex shaft
to the snow thrower frame and lightly tap the shaft’s end to
dislodge the ball bearing from the right side of the frame.
See Figure 7-8.
7.
Follow the previous steps in reverse order to reassemble
components.
8.
Perform the Drive Control test on page 18 in the
Maintenance and Adjustments section.
NOTE: Be careful not to damage the threads on the shaft.
If you’re disassembling the friction wheel and replacing only the
rubber ring, proceed as follows:
NOTE: Not all friction wheels are serviceable. If this is the case,
simply replace the friction wheel assembly.
1.
Remove the four screws which secure the friction wheel’s
side plates together. See Figure 7-10.
Figure 7-8
6.
Carefully position the hex shaft downward and to the left
before carefully sliding the friction wheel assembly off the
shaft. See Figure 7-9.
Figure 7-10
2.
3.
Remove the rubber ring from between the plates.
Reassemble the side plates with a new rubber ring.
NOTE: When reassembling the friction wheel assembly,
make sure that the rubber ring is centered and seated
properly between the side plates. Tighten each screw
only one rotation before turning the wheel clockwise
and proceeding with the next screw. Repeat this process
several times to ensure the plates are secured with equal
force (between 6 ft-lbs and 9 ft-lbs).
NOTE: Make sure the shift lever pin is in place in the
bearing housing. See Figure 7-8 inset.
4.
5.
Slide the friction wheel assembly back onto the hex shaft
and follow the steps above in reverse order to reassemble
components.
After replacing the friction wheel, perform the Drive
Control test on page 18 in the Maintenance and
Adjustments section.
Figure 7-9
NOTE: If you’re replacing the friction wheel assembly as a
whole, discard the worn part and slide the new part onto
the hex shaft.
22
Section 7 — Service
Troubleshooting
8
Problem
Cause
Remedy
Engine fails to start
1. Choke not in CHOKE position.
2. Spark plug wire disconnected.
3. Fuel tank empty or stale fuel.
4. Engine not primed.
1. Move choke to CHOKE position.
2. Connect wire to spark plug.
3. Fill tank with clean, fresh gasoline.
4. Prime engine as instructed in the Engine
Operator’s Manual.
5. Faulty spark plug.
5. Clean, adjust gap, or replace.
6. Insert key fully into the switch.
6. Key not in ignition on engine.
7. Extension cord not connected.
7. Connect one end of the extension cord to the
electric starter outlet and the other end to a
three-prong 120-volt, grounded, AC outlet.
Engine running erratically/
inconsistent RPM (hunting
or surging)
1. Engine running on CHOKE.
2. Stale fuel.
1. Move choke lever to RUN position.
2. Fill tank with clean, fresh gasoline.
3. Drain fuel tank. Refill with fresh fuel.
4. Contact an authorized Service Center.
5. Contact an authorized Service Center.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
5. Engine over-governed
Engine overheats
Excessive vibration
1. Carburetor not adjusted properly.
1. Loose parts or damaged auger.
1. Contact an authorized Service Center.
1. Stop engine immediately and disconnect spark
plug wire. Tighten all bolts and nuts. If vibration
continues, have unit serviced by an authorized
Service Center.
Loss of power
1. Spark plug wire loose.
1. Connect and tighten spark plug wire.
2. Gas cap vent hole plugged.
2. Remove ice and snow from gas cap. Be certain
vent hole is clear.
Unit fails to propel itself
1. Drive control cable in need of adjustment.
1. Adjust drive control cable. Refer to Maintenance
& Adjustments section.
2. Drive belt loose or damaged.
3. Friction wheel worn.
2. Contact an authorized Service Center.
3. Replace friction wheel. Refer to Service section.
Unit fails to discharge snow
1. Chute assembly clogged.
1. Stop engine immediately and disconnect spark
plug wire. Clean chute assembly and inside of
auger housing with clean-out tool or a stick.
2. Foreign object lodged in auger.
2. Stop engine immediately and disconnect spark
plug wire. Remove object from auger with clean-
out tool or a stick.
3. Auger control cable in need of
adjustment.
3. Refer to Auger Control Test.
4. Auger belt loose or damaged.
5. Shear pin(s) sheared.
4. Refer to Maintenance & Adjustments section.
5. Replace with new shear pin(s).
Chute fails to easily rotate
180 degrees
1. Chute assembled incorrectly.
1. Unassemble chute control and reassemble as
directed in the Assembly section.
23
Replacement Parts
9
Component
Part Number and Description
954-04050A
954-04260
954-04195A
954-04201A
Auger Drive Belt (2X 524 WE, 2X 524 SWE, & 2X 526 SWE)
Wheel Drive Belt (2X 524 WE, 2X 524 SWE, & 2X 526 SWE)
Auger Drive Belt (2X 528 SWE & 2X 530 SWE)
Wheel Drive Belt (2X 528 SWE & 2X 530 SWE)
684-04153C
935-04054
Friction Wheel Assembly
Friction Wheel Rubber (all models)
925-1629
Lamp, 12V
738-04124A
714-04040
Shear Pin, 1.50
Bow-tie Cotter Pin
731-06931
931-2643
Skid Shoe, Deluxe
Chute Clean-out Tool
790-00120
790-00121
790-00148
790-00118
790-00145
790-00119
790-00146
Shave Plate (2X 524 WE & 2X 524 SWE)
Shave Plate (2X 526 SWE)
Stainless Steel Shave Plate (2X 526 SWE)
Shave Plate (2X 528 SWE)
Stainless Steel Shave Plate (2X 528 SWE)
Shave Plate (2X 530 SWE)
Stainless Steel Shave Plate (2X 530 SWE)
951-10630
951-10292
Key
Spark Plug
Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number
24
Attachments & Accessories
10
The following attachments and accessories are available for your Cub Cadet snow thrower. See your Cub Cadet dealer or the retailer
from which you purchased your snow thrower for information regarding price and availability.
Model Number
Description
929-0071A
753-05762A
Extension Cord, 110V
Heated Grips*
OEM-390-679
490-241-0032
490-241-0013
490-241-0038
490-290-0010
490-241-0028
490-241-0029
490-900-0062
490-240-0011
490-850-0008
490-000-0028
490-325-0020
490-325-0022
490-850-0013
490-850-0014
22208
Drift Cutter Kit
Snow Cab
Snow Thrower Auger and Chute Maintenance Kit
Roller Skid Shoes
Snow Thrower Cover
Snow Thrower Tire Chains (16” x 4.8” Tires)
Snow Thrower Tire Chains (16” x 6.5” Tires)
Non-Stick Spray
Fuel Test Swabs
Siphon Pump
Carburetor and Choke Cleaner
32 oz. Tire and Tube Sealant
16 oz. Tire and Tube Sealant
Tire/Tube Foot Pump
Deluxe Tire Plug Kit
8 oz. Fuel Stabilizer
22216
32 oz. Fuel Stabilizer
*Compatible on models equipped with a split alternator.
25
26
27
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY FOR SNOW THROWERS, LOG SPLITTERS
CHIPPER-SHREDDERS, CHIPPER-SHREDDER VACUUMS AND JET SWEEPS
The limited warranty set forth below is given by Cub Cadet LLC
with respect to new merchandise purchased and used in the United
States, its possessions and territories, and by MTD Products Limited
with respect to new merchandise purchased and used in Canada
and/or its territories and possessions.
a.
Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments,
deck adjustments, and normal deterioration of the exterior
finish due to use or exposure.
b.
c.
Log splitter pumps, valves, and cylinders have a separate one
year warranty.
This warranty is in addition to any applicable emissions warranty
provided with your product.
Cub Cadet does not extend any warranty for products sold
or exported outside of the United States and/or Canada, and
their respective possessions and territories, except those
sold through Cub Cadet’s authorized channels of export
distribution.
For non-commercial use: Cub Cadet warrants this product
(excluding Normal Wear Parts and the Auger Gearbox, as described
below) against defects in material and workmanship for a period of
three (3) years from the date of original retail purchase or lease.
For commercial uses and applications: Cub Cadet warrants this
product (excluding Normal Wear Parts and the Auger Gearbox, as
described below) against defects in material and workmanship for
a period of one (1) year from the date of original retail purchase or
lease.
d.
e.
Replacement parts that are not genuine Cub Cadet parts.
Service completed by someone other than an authorized
service dealer.
f.
Transportation charges and service calls.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose, applies
after the applicable period of express written warranty above
as to the parts as identified. No other express warranty,
whether written or oral, except as mentioned above, given by
any person or entity, including a dealer or retailer, with respect
to any product, shall bind Cub Cadet. During the period of the
warranty, the exclusive remedy is repair or replacement of the
product as set forth above.
“Cub Cadet” will, at its option, repair or replace, free of charge, any
part found to be defective in materials or workmanship. This limited
warranty shall only apply if this product has been operated and
maintained in accordance with the Operator’s Manual furnished
with the product, and has not been subject to misuse, abuse,
neglect, accident, improper maintenance, alteration, vandalism,
theft, fire, water, or damage because of other peril or natural
disaster. Damage resulting from the installation or use of any part,
accessory or attachment not approved by Cub Cadet for use with
the product(s) covered by this manual will void your warranty as to
any resulting damage.
The provisions as set forth in this warranty provide the sole
and exclusive remedy arising from the sale. Cub Cadet shall
not be liable for incidental or consequential loss or damage
including, without limitation, expenses incurred for substitute
or replacement lawn care services or for rental expenses to
temporarily replace a warranted product.
Normal Wear Parts are warranted to be free from defects in material
and workmanship for a period of thirty (30) days from the date of
purchase. Normal wear parts include, but are not limited to items
such as: belts, skid shoes, shave plates, blades, debris collection
bags, wheels and tires.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts, so the above exclusions or limitations may not apply
to you.
Auger Gearbox — Cub Cadet warrants the auger gearbox (on three-
stage snow thrower models only) against defects in material and
workmanship for a period of five (5) years, commencing on the date
of the snow thrower’s original purchase.
In no event shall recovery of any kind be greater than the amount
of the purchase price of the product sold. Alteration of safety
features of the product shall void this warranty. You assume the
risk and liability for loss, damage, or injury to you and your property
and/or to others and their property arising out of the misuse or
inability to use the product.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service dealer.
To locate the dealer in your area:
In the U.S.A.
To locate the dealer in your area, check your Yellow Pages, or
contact Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-
0019, or call 1-877-282-8684, or log on to our Web site at www.
cubcadet.com.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased as a
gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have
other rights that vary in different jurisdictions.
In Canada
Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call
IMPORTANT: Owner must present Original Proof of Purchase to
This limited warranty does not provide coverage in the following
cases:
obtain warranty coverage.
Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-877-282-8684
MTD Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
GDOC-100160 REV. C
|